ARM: dts: add support to DB600ctracking-qcomlt-apq8064-dt

This patch adds support to DB600c P1 board, which is subjected to
change.

Here is the list of things tested on this board and know issues.

Tested:
-------------------

1> UART: Only DEBUG uart has been tested.

2> 2 USB ports on the board are tested with USB stick.

3> PCIE  and ETHERNET, Tested with Wired Ethernet on board.

4>  LEDs: Heart beat LED seems to work fine.

5> eMMC: tested with rootfs.

6> HDMI: Tested with FB console.

Hardware issues:
-------------------

1> I2C: 2 instances of GSBIs are wired up with 2 I2C instances on each
of them. which seems to be a issue because each gsbi has only one I2C
instance.

2> SATA: There seems to be issue with both andriod and Linux kernels to
detect few types of disks, this issue needs more understanding by
looking a sata eye-diagram

NOT Tested:
-------------------
1> SPI@

2> All the LEDS

3> SD CARD: SD card on linux seems to not work, Am debugging this issue,
it could a software issue.

4> WLAN: Not tested as its subjected to change.

5> AUDIO: Not tested, will test digital audio in next week. Analog audio
has dependency on Sagar's Slim Bus Patches.

6> Debian Desktop: There seems to be a issue with Splash screen enabled
bootloaders. When we try to bringup the display it goes blue, however
same software works fine on IFC6410. Am guessing that this could be
issue due to clks handover from bootloader to linux w.r.t display.

7> SAW Regulators: Looks like there is an issue if we attempt to enable
SAW regualtors, I have not spend much time to look at this issue, but I
will start debugging this very soon.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

3 files changed, 491 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4b17f35dc9a71..0901f565eb71d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -683,6 +683,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-apq8064-ifc6410.dtb \
 	qcom-apq8064-sony-xperia-yuga.dtb \
 	qcom-apq8064-asus-nexus7-flo.dtb \
+	qcom-apq8064-db600c.dtb \
 	qcom-apq8074-dragonboard.dtb \
 	qcom-apq8084-ifc6540.dtb \
 	qcom-apq8084-mtp.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-db600c-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-db600c-pins.dtsi
new file mode 100644
index 0000000000000..cb2370343c34f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-db600c-pins.dtsi
@@ -0,0 +1,70 @@
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+&tlmm_pinmux {
+	card_detect: card-detect {
+		mux {
+			pins = "gpio26";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	user_leds: user-leds {
+		mux {
+			pins = "gpio6", "gpio7", "gpio35", "gpio86";
+			function = "gpio";
+		};
+
+		conf {
+			pins = "gpio6", "gpio7", "gpio35", "gpio86";
+			function = "gpio";
+			output-low;
+		};
+	};
+
+	magneto_pins: magneto-pins {
+		mux {
+			pins = "gpio31", "gpio48";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+};
+
+&pm8921_gpio {
+
+	pcie_pins: pcie_pins {
+		pios {
+			pins = "gpio22";
+			function = "normal";
+			power-source = <PM8921_GPIO_VPH>;
+		};
+	};
+};
+&pm8921_mpps {
+
+	sataclk_pins: sataclk-pins {
+		pinconf {
+			pins = "mpp4";
+			function = "digital";
+			power-source = <PM8921_MPP_VPH>;
+		};
+	};
+	pcie_perst: pcie-perst {
+		pinconf {
+			pins = "mpp1";
+			function = "digital";
+			power-source = <PM8921_MPP_S4>;
+			output-low;
+		};
+	};
+
+	mpp_leds: mpp-leds {
+		pinconf {
+			pins = "mpp7", "mpp8";
+			function = "digital";
+			output-low;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-db600c.dts b/arch/arm/boot/dts/qcom-apq8064-db600c.dts
new file mode 100644
index 0000000000000..aacb94daaae5c
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-db600c.dts
@@ -0,0 +1,420 @@
+#include "qcom-apq8064-v2.0.dtsi"
+#include "qcom-apq8064-db600c-pins.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+
+/ {
+	model = "Qualcomm Technologies, Inc. DB600c";
+	compatible = "arrow,apq8064-db820c", "qcom,apq8064-sbc", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi1_serial;
+		i2c0 = &gsbi2_i2c;
+//		i2c1 = &gsbi3_i2c;
+		i2c2 = &gsbi4_i2c;
+		i2c3 = &gsbi7_i2c;
+		spi0 = &gsbi5_spi;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		vph: regulator-fixed@1 {
+			compatible = "regulator-fixed";
+			regulator-min-microvolt = <4500000>;
+			regulator-max-microvolt = <4500000>;
+			regulator-name = "VPH";
+			regulator-type = "voltage";
+			regulator-boot-on;
+		};
+
+		/* on board fixed 3.3v supply */
+		vcc3v3: vcc3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "VCC3V3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&hdmi_out>;
+			};
+		};
+	};
+
+	soc {
+		rpm@108000 {
+			regulators {
+				vdd_s1-supply = <&vph>;
+				vdd_s2-supply = <&vph>;
+				vdd_s3-supply = <&vph>;
+				vdd_s4-supply = <&vph>;
+				vdd_s5-supply = <&vph>;
+				vdd_s6-supply = <&vph>;
+				vdd_s7-supply = <&vph>;
+
+				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+				vdd_l3_l15_l17-supply = <&vph>;
+				vdd_l4_l14-supply = <&vph>;
+				vdd_l5_l8_l16-supply = <&vph>;
+				vdd_l6_l7-supply = <&vph>;
+				vdd_l9_l11-supply = <&vph>;
+				vdd_l10_l22-supply = <&vph>;
+				vdd_l21_l23_l29-supply = <&vph>;
+
+				vdd_l24-supply = <&pm8921_s1>;
+				vdd_l25-supply = <&pm8921_s1>;
+				vdd_l26-supply = <&pm8921_s7>;
+				vdd_l27-supply = <&pm8921_s7>;
+				vdd_l28-supply = <&pm8921_s7>;
+
+				vin_lvs1_3_6-supply = <&pm8921_s4>;
+				vin_lvs2-supply = <&pm8921_s1>;
+				vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+				s1 {
+					regulator-always-on;
+					regulator-min-microvolt = <1225000>;
+					regulator-max-microvolt = <1225000>;
+					qcom,switch-mode-frequency = <3200000>;
+					bias-pull-down;
+				};
+
+				s2 {
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+					regulator-always-on;
+				};
+
+				s3 {
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1400000>;
+					qcom,switch-mode-frequency = <4800000>;
+				};
+
+				s4 {
+					regulator-min-microvolt	= <1800000>;
+					regulator-max-microvolt	= <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+					bias-pull-down;
+					regulator-always-on;
+				};
+
+				s7 {
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <3200000>;
+				 };
+
+				l3 {
+					regulator-min-microvolt = <3050000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+
+				l4 {
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+
+				l5 {
+					regulator-min-microvolt = <2750000>;
+					regulator-max-microvolt = <3000000>;
+					bias-pull-down;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				l6 {
+					regulator-min-microvolt = <2950000>;
+					regulator-max-microvolt = <2950000>;
+					bias-pull-down;
+				};
+
+				l7 {
+					regulator-min-microvolt = <2950000>;
+					regulator-max-microvolt = <2950000>;
+					bias-pull-down;
+				};
+
+				/**
+				/**
+				 * 1.8v required on LS expansion
+				 * for mezzanine boards
+				 */
+				l15 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				l23 {
+					regulator-min-microvolt = <1700000>;
+					regulator-max-microvolt = <1900000>;
+					bias-pull-down;
+				};
+
+				lvs6 {
+					bias-pull-down;
+				};
+
+				lvs7 {
+					bias-pull-down;
+				};
+			};
+		};
+
+		gsbi@12440000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_UART_W_FC>;
+			serial@12450000 {
+				label = "LS-UART1";
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsbi1_uart_4pins>;
+			};
+		};
+
+		gsbi@12480000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C>;
+			i2c@124a0000 {
+				/* On Low speed expansion and Sensors */
+				label = "LS-I2C0";
+				status = "okay";
+			};
+		};
+#if 0
+//FIXME 
+		gsbi@16200000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C>;
+			i2c@16280000 {
+			/* On Low speed expansion */
+				status = "okay";
+				label = "LS-I2C1";
+				clock-frequency = <200000>;
+				eeprom@52 {
+					compatible = "atmel,24c128";
+					reg = <0x52>;
+					pagesize = <64>;
+				};
+			};
+		};
+#endif
+
+		gsbi@16300000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C>;
+			i2c@16380000 {
+				/* On High speed expansion */
+				label = "HS-CAM-I2C3";
+				status = "okay";
+			};
+		};
+
+		gsbi@1a200000 {
+			status = "okay";
+			spi@1a280000 {
+				/* On Low speed expansion */
+				label = "LS-SPI0";
+				status = "okay";
+			};
+		};
+
+		/* DEBUG UART  */
+		gsbi@16600000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			serial@16640000 {
+				label = "LS-UART0";
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsbi7_uart_2pins>;
+
+};
+#if 0
+//FIXME 
+
+			i2c@16680000 {
+				/* On High speed expansion */
+				status = "okay";
+				label = "HS-CAM-I2C2";
+			};
+#endif
+		};
+
+		leds {
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_leds>, <&mpp_leds>;
+
+			compatible = "gpio-leds";
+
+			user-led0 {
+				label = "user0-led";
+				gpios = <&tlmm_pinmux 6 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "heartbeat";
+				default-state = "off";
+			};
+
+			user-led1 {
+				label = "user1-led";
+				gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "mmc0";
+				default-state = "off";
+			};
+
+			user-led2 {
+				label = "user2-led";
+				gpios = <&tlmm_pinmux 35 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "mmc1";
+				default-state = "off";
+			};
+
+			user-led3 {
+				label = "user3-led";
+				gpios = <&tlmm_pinmux 86 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "none";
+				default-state = "off";
+			};
+
+			wifi-led {
+				label = "WiFi-led";
+				gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+
+			bt-led {
+				label = "BT-led";
+				gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
+
+		pci@1b500000 {
+			status = "okay";
+			vdda-supply = <&pm8921_s3>;
+			vdda_phy-supply = <&pm8921_lvs6>;
+			vdda_refclk-supply = <&vcc3v3>;
+
+
+			pinctrl-0 = < &pcie_pins &pcie_perst>;
+			pinctrl-names = "default";
+			perst-gpio = <&pm8921_mpps 1 GPIO_ACTIVE_LOW>;
+			clkoe-gpio = <&pm8921_gpio 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		phy@1b400000 {
+			pinctrl-0 = < &sataclk_pins>;
+			status = "okay";
+			clkoe-gpio = <&pm8921_mpps 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata@29000000 {
+			status	= "okay";
+			target-supply	= <&pm8921_lvs7>;
+		};
+
+		usb1_phy: phy@12500000 {
+			status		= "okay";
+			vddcx-supply	= <&pm8921_s3>;
+			v3p3-supply	= <&pm8921_l3>;
+			v1p8-supply	= <&pm8921_l4>;
+		};
+
+
+		usb3_phy: phy@12520000 {
+			status		= "okay";
+			vddcx-supply	= <&pm8921_s3>;
+			v3p3-supply	= <&pm8921_l3>;
+			v1p8-supply	= <&pm8921_l23>;
+		};
+
+		usb4_phy: phy@12530000 {
+			status		= "okay";
+			vddcx-supply	= <&pm8921_s3>;
+			v3p3-supply	= <&pm8921_l3>;
+			v1p8-supply	= <&pm8921_l23>;
+		};
+
+		gadget1: gadget@12500000 {
+			status = "okay";
+		};
+
+		/* OTG */
+		usb1: usb@12500000 {
+			status = "okay";
+		};
+
+		usb3: usb@12520000 {
+			status = "okay";
+		};
+
+		usb4: usb@12530000 {
+			status = "okay";
+		};
+
+		amba {
+			/* eMMC */
+			sdcc@12400000 {
+				status = "okay";
+				vmmc-supply = <&pm8921_l5>;
+				vqmmc-supply = <&pm8921_s4>;
+			};
+
+			/* External micro SD card */
+			sdcc@12180000 {
+				status = "okay";
+				vmmc-supply = <&pm8921_l6>;
+				pinctrl-names	= "default";
+				pinctrl-0	= <&card_detect>;
+				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+			};
+		};
+
+		hdmi-tx@4a00000 {
+			status = "okay";
+			core-vdda-supply = <&pm8921_hdmi_switch>;
+			hdmi-mux-supply = <&vcc3v3>;
+
+			hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
+
+			ports {
+				port@1 {
+					endpoint {
+						remote-endpoint = <&hdmi_con>;
+					};
+				};
+			};
+		};
+
+		hdmi-phy@4a00400 {
+			status = "okay";
+			core-vdda-supply = <&pm8921_hdmi_switch>;
+		};
+
+		mdp@5100000 {
+			status = "okay";
+
+			ports {
+				port@3 {
+					endpoint {
+						remote-endpoint = <&hdmi_in>;
+					};
+				};
+			};
+		};
+	};
+};