aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/intel/ixgbe/ixgbe_common.c')
-rw-r--r--drivers/net/ethernet/intel/ixgbe/ixgbe_common.c226
1 files changed, 220 insertions, 6 deletions
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 3f56a8080118..ce61b36b94f1 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -297,13 +297,13 @@ s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw)
/* Setup flow control */
ret_val = ixgbe_setup_fc(hw);
- if (!ret_val)
- return 0;
+ if (ret_val)
+ return ret_val;
/* Clear adapter stopped flag */
hw->adapter_stopped = false;
- return ret_val;
+ return 0;
}
/**
@@ -2164,10 +2164,11 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw)
/*
* In order to prevent Tx hangs when the internal Tx
* switch is enabled we must set the high water mark
- * to the maximum FCRTH value. This allows the Tx
- * switch to function even under heavy Rx workloads.
+ * to the Rx packet buffer size - 24KB. This allows
+ * the Tx switch to function even under heavy Rx
+ * workloads.
*/
- fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 32;
+ fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576;
}
IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth);
@@ -2476,6 +2477,9 @@ static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw)
hw_dbg(hw, "GIO Master Disable bit didn't clear - requesting resets\n");
hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
+ if (hw->mac.type >= ixgbe_mac_X550)
+ return 0;
+
/*
* Before proceeding, make sure that the PCIe block does not have
* transactions pending.
@@ -3920,3 +3924,213 @@ bool ixgbe_mng_present(struct ixgbe_hw *hw)
fwsm &= IXGBE_FWSM_MODE_MASK;
return fwsm == IXGBE_FWSM_FW_MODE_PT;
}
+
+/**
+ * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Set the link speed in the MAC and/or PHY register and restarts link.
+ */
+s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
+{
+ ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+ ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+ s32 status = 0;
+ u32 speedcnt = 0;
+ u32 i = 0;
+ bool autoneg, link_up = false;
+
+ /* Mask off requested but non-supported speeds */
+ status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg);
+ if (status)
+ return status;
+
+ speed &= link_speed;
+
+ /* Try each speed one by one, highest priority first. We do this in
+ * software because 10Gb fiber doesn't support speed autonegotiation.
+ */
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
+ speedcnt++;
+ highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+ false);
+ if (status)
+ return status;
+
+ if (link_speed == IXGBE_LINK_SPEED_10GB_FULL && link_up)
+ goto out;
+
+ /* Set the module link speed */
+ switch (hw->phy.media_type) {
+ case ixgbe_media_type_fiber:
+ hw->mac.ops.set_rate_select_speed(hw,
+ IXGBE_LINK_SPEED_10GB_FULL);
+ break;
+ case ixgbe_media_type_fiber_qsfp:
+ /* QSFP module automatically detects MAC link speed */
+ break;
+ default:
+ hw_dbg(hw, "Unexpected media type\n");
+ break;
+ }
+
+ /* Allow module to change analog characteristics (1G->10G) */
+ msleep(40);
+
+ status = hw->mac.ops.setup_mac_link(hw,
+ IXGBE_LINK_SPEED_10GB_FULL,
+ autoneg_wait_to_complete);
+ if (status)
+ return status;
+
+ /* Flap the Tx laser if it has not already been done */
+ if (hw->mac.ops.flap_tx_laser)
+ hw->mac.ops.flap_tx_laser(hw);
+
+ /* Wait for the controller to acquire link. Per IEEE 802.3ap,
+ * Section 73.10.2, we may have to wait up to 500ms if KR is
+ * attempted. 82599 uses the same timing for 10g SFI.
+ */
+ for (i = 0; i < 5; i++) {
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ status = hw->mac.ops.check_link(hw, &link_speed,
+ &link_up, false);
+ if (status)
+ return status;
+
+ if (link_up)
+ goto out;
+ }
+ }
+
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
+ speedcnt++;
+ if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
+ highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+ false);
+ if (status)
+ return status;
+
+ if (link_speed == IXGBE_LINK_SPEED_1GB_FULL && link_up)
+ goto out;
+
+ /* Set the module link speed */
+ switch (hw->phy.media_type) {
+ case ixgbe_media_type_fiber:
+ hw->mac.ops.set_rate_select_speed(hw,
+ IXGBE_LINK_SPEED_1GB_FULL);
+ break;
+ case ixgbe_media_type_fiber_qsfp:
+ /* QSFP module automatically detects link speed */
+ break;
+ default:
+ hw_dbg(hw, "Unexpected media type\n");
+ break;
+ }
+
+ /* Allow module to change analog characteristics (10G->1G) */
+ msleep(40);
+
+ status = hw->mac.ops.setup_mac_link(hw,
+ IXGBE_LINK_SPEED_1GB_FULL,
+ autoneg_wait_to_complete);
+ if (status)
+ return status;
+
+ /* Flap the Tx laser if it has not already been done */
+ if (hw->mac.ops.flap_tx_laser)
+ hw->mac.ops.flap_tx_laser(hw);
+
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+ false);
+ if (status)
+ return status;
+
+ if (link_up)
+ goto out;
+ }
+
+ /* We didn't get link. Configure back to the highest speed we tried,
+ * (if there was more than one). We call ourselves back with just the
+ * single highest speed that the user requested.
+ */
+ if (speedcnt > 1)
+ status = ixgbe_setup_mac_link_multispeed_fiber(hw,
+ highest_link_speed,
+ autoneg_wait_to_complete);
+
+out:
+ /* Set autoneg_advertised value based on input link speed */
+ hw->phy.autoneg_advertised = 0;
+
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
+
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL)
+ hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
+
+ return status;
+}
+
+/**
+ * ixgbe_set_soft_rate_select_speed - Set module link speed
+ * @hw: pointer to hardware structure
+ * @speed: link speed to set
+ *
+ * Set module link speed via the soft rate select.
+ */
+void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed)
+{
+ s32 status;
+ u8 rs, eeprom_data;
+
+ switch (speed) {
+ case IXGBE_LINK_SPEED_10GB_FULL:
+ /* one bit mask same as setting on */
+ rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
+ break;
+ case IXGBE_LINK_SPEED_1GB_FULL:
+ rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
+ break;
+ default:
+ hw_dbg(hw, "Invalid fixed module speed\n");
+ return;
+ }
+
+ /* Set RS0 */
+ status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+ IXGBE_I2C_EEPROM_DEV_ADDR2,
+ &eeprom_data);
+ if (status) {
+ hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
+ return;
+ }
+
+ eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
+
+ status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+ IXGBE_I2C_EEPROM_DEV_ADDR2,
+ eeprom_data);
+ if (status) {
+ hw_dbg(hw, "Failed to write Rx Rate Select RS0\n");
+ return;
+ }
+}
generated by cgit v1.2.3 (git 2.25.1) at 2024-04-26 07:47:35 +0000