diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/wireless')
18 files changed, 1445 insertions, 297 deletions
diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml b/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml new file mode 100644 index 000000000000..c11f23b20c4c --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM4329 family fullmac wireless SDIO devices + +maintainers: + - Arend van Spriel <arend@broadcom.com> + +description: + The Broadcom Single chip MAC part for the BCM4329 family and + later Cypress chips in the same family named CYW4373 and similar. + These chips also have a Bluetooth portion described in a separate + binding. + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,bcm43143-fmac + - brcm,bcm4341b0-fmac + - brcm,bcm4341b4-fmac + - brcm,bcm4341b5-fmac + - brcm,bcm4329-fmac + - brcm,bcm4330-fmac + - brcm,bcm4334-fmac + - brcm,bcm43340-fmac + - brcm,bcm4335-fmac + - brcm,bcm43362-fmac + - brcm,bcm4339-fmac + - brcm,bcm43430a0-fmac + - brcm,bcm43430a1-fmac + - brcm,bcm43455-fmac + - brcm,bcm43456-fmac + - brcm,bcm4354-fmac + - brcm,bcm4356-fmac + - brcm,bcm4359-fmac + - cypress,cyw4373-fmac + - cypress,cyw43012-fmac + - const: brcm,bcm4329-fmac + - const: brcm,bcm4329-fmac + + reg: + description: SDIO function number for the device, for most cases + this will be 1. + + interrupts: + maxItems: 1 + description: Out-of-band (OOB) IRQ line for waking up the host + in response to WLAN activity. This corresponds to the HOST_WAKE + line into the chip. + + interrupt-names: + description: Name for the OOB IRQ, this must be set to "host-wake". + const: host-wake + + brcm,drive-strength: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Drive strength used for the SDIO pins on the device in mA. + minimum: 0 + maximum: 32 + + reset-gpios: + maxItems: 1 + description: A GPIO line connected to the WL_RST line, if present + this shall be flagged as active low. + + brcm,ccode-map: + $ref: /schemas/types.yaml#/definitions/string-array + description: Multiple strings for translating ISO3166 country code to + brcmfmac firmware country code and revision. + items: + pattern: '^[A-Z][A-Z]-[A-Z][0-9A-Z]-[0-9]+$' + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + mmc@80118000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80118000 0x1000>; + clocks = <&clk 0>, <&clk 1>; + clock-names = "mclk", "apb_pclk"; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + bus-width = <4>; + non-removable; + vmmc-supply = <&wl_bt_reg>; + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; + reg = <1>; + interrupt-parent = <&gpio>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "host-wake"; + reset-gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + brcm,ccode-map = "JP-JP-78", "US-Q2-86"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt deleted file mode 100644 index cffb2d6876e3..000000000000 --- a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt +++ /dev/null @@ -1,38 +0,0 @@ -Broadcom BCM43xx Fullmac wireless SDIO devices - -This node provides properties for controlling the Broadcom wireless device. The -node is expected to be specified as a child node to the SDIO controller that -connects the device to the system. - -Required properties: - - - compatible : Should be "brcm,bcm4329-fmac". - -Optional properties: - - brcm,drive-strength : drive strength used for SDIO pins on device in mA - (default = 6). - - interrupts : specifies attributes for the out-of-band interrupt (host-wake). - When not specified the device will use in-band SDIO interrupts. - - interrupt-names : name of the out-of-band interrupt, which must be set - to "host-wake". - -Example: - -mmc3: mmc@1c12000 { - #address-cells = <1>; - #size-cells = <0>; - - pinctrl-names = "default"; - pinctrl-0 = <&mmc3_pins_a>; - vmmc-supply = <®_vmmc3>; - bus-width = <4>; - non-removable; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - interrupt-parent = <&pio>; - interrupts = <10 8>; /* PH10 / EINT10 */ - interrupt-names = "host-wake"; - }; -}; diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt deleted file mode 100644 index 6830c4786f8a..000000000000 --- a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt +++ /dev/null @@ -1,30 +0,0 @@ -Espressif ESP8089 wireless SDIO devices - -This node provides properties for controlling the ESP8089 wireless device. -The node is expected to be specified as a child node to the SDIO controller -that connects the device to the system. - -Required properties: - - - compatible : Should be "esp,esp8089". - -Optional properties: - - esp,crystal-26M-en: Integer value for the crystal_26M_en firmware parameter - -Example: - -&mmc1 { - #address-cells = <1>; - #size-cells = <0>; - - vmmc-supply = <®_dldo1>; - mmc-pwrseq = <&wifi_pwrseq>; - bus-width = <4>; - non-removable; - - esp8089: sdio_wifi@1 { - compatible = "esp,esp8089"; - reg = <1>; - esp,crystal-26M-en = <2>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.yaml b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.yaml new file mode 100644 index 000000000000..284ef45add99 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/esp,esp8089.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Espressif ESP8089 Device Tree Bindings + +maintainers: + - Hans de Goede <hdegoede@redhat.com> + +properties: + compatible: + const: esp,esp8089 + + reg: + maxItems: 1 + + esp,crystal-26M-en: + $ref: /schemas/types.yaml#/definitions/uint32 + description: > + Value for the crystal_26M_en firmware parameter + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + mmc { + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "esp,esp8089"; + reg = <1>; + esp,crystal-26M-en = <2>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/net/wireless/ieee80211.txt b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt deleted file mode 100644 index f6442b1397f5..000000000000 --- a/Documentation/devicetree/bindings/net/wireless/ieee80211.txt +++ /dev/null @@ -1,24 +0,0 @@ -Common IEEE 802.11 properties - -This provides documentation of common properties that are valid for all wireless -devices. - -Optional properties: - - ieee80211-freq-limit : list of supported frequency ranges in KHz. This can be - used for devices that in a given config support less channels than - normally. It may happen chipset supports a wide wireless band but it is - limited to some part of it due to used antennas or power amplifier. - An example case for this can be tri-band wireless router with two - identical chipsets used for two different 5 GHz subbands. Using them - incorrectly could not work or decrease performance noticeably. - -Example: - -pcie@0,0 { - reg = <0x0000 0 0 0 0>; - wifi@0,0 { - reg = <0x0000 0 0 0 0>; - ieee80211-freq-limit = <2402000 2482000>, - <5170000 5250000>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/wireless/ieee80211.yaml b/Documentation/devicetree/bindings/net/wireless/ieee80211.yaml new file mode 100644 index 000000000000..d58e1571df9b --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ieee80211.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved. + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/ieee80211.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common IEEE 802.11 Binding + +maintainers: + - Lorenzo Bianconi <lorenzo@kernel.org> + +description: | + This provides documentation of common properties that are valid for + all wireless devices + +properties: + ieee80211-freq-limit: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + minItems: 2 + maxItems: 2 + description: + List of supported frequency ranges in KHz. This can be used for devices + that in a given config support less channels than normally. It may happen + chipset supports a wide wireless band but it is limited to some part of + it due to used antennas or power amplifier. An example case for this + can be tri-band wireless router with two identical chipsets used for two + different 5 GHz subbands. Using them incorrectly could not work or + decrease performance noticeably + +additionalProperties: true + +examples: + - | + pcie0 { + #address-cells = <3>; + #size-cells = <2>; + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <2402000 2482000>, + <5170000 5250000>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt deleted file mode 100644 index 7e675dafc256..000000000000 --- a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt +++ /dev/null @@ -1,52 +0,0 @@ -* MediaTek mt76xx devices - -This node provides properties for configuring the MediaTek mt76xx wireless -device. The node is expected to be specified as a child node of the PCI -controller to which the wireless chip is connected. - -Alternatively, it can specify the wireless part of the MT7628/MT7688 SoC. -For SoC, use the compatible string "mediatek,mt7628-wmac" and the following -properties: - -- reg: Address and length of the register set for the device. -- interrupts: Main device interrupt - -Optional properties: - -- ieee80211-freq-limit: See ieee80211.txt -- mediatek,mtd-eeprom: Specify a MTD partition + offset containing EEPROM data - -The MAC address can as well be set with corresponding optional properties -defined in net/ethernet.txt. - -Optional nodes: -- led: Properties for a connected LED - Optional properties: - - led-sources: See Documentation/devicetree/bindings/leds/common.txt - -&pcie { - pcie0 { - wifi@0,0 { - compatible = "mediatek,mt76"; - reg = <0x0000 0 0 0 0>; - ieee80211-freq-limit = <5000000 6000000>; - mediatek,mtd-eeprom = <&factory 0x8000>; - - led { - led-sources = <2>; - }; - }; - }; -}; - -MT7628 example: - -wmac: wmac@10300000 { - compatible = "mediatek,mt7628-wmac"; - reg = <0x10300000 0x100000>; - - interrupt-parent = <&cpuintc>; - interrupts = <6>; - - mediatek,mtd-eeprom = <&factory 0x0000>; -}; diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml new file mode 100644 index 000000000000..5a12dc32288a --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml @@ -0,0 +1,273 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved. + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/mediatek,mt76.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek mt76 wireless devices Generic Binding + +maintainers: + - Felix Fietkau <nbd@nbd.name> + - Lorenzo Bianconi <lorenzo@kernel.org> + - Ryder Lee <ryder.lee@mediatek.com> + +description: | + This node provides properties for configuring the MediaTek mt76xx + wireless device. The node is expected to be specified as a child + node of the PCI controller to which the wireless chip is connected. + Alternatively, it can specify the wireless part of the MT7628/MT7688 + or MT7622/MT7986 SoC. + +allOf: + - $ref: ieee80211.yaml# + +properties: + compatible: + enum: + - mediatek,mt76 + - mediatek,mt7628-wmac + - mediatek,mt7622-wmac + - mediatek,mt7986-wmac + + reg: + minItems: 1 + maxItems: 3 + description: + MT7986 should contain 3 regions consys, dcm, and sku, in this order. + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + memory-region: + maxItems: 1 + + resets: + maxItems: 1 + description: + Specify the consys reset for mt7986. + + reset-names: + const: consys + + mediatek,infracfg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the infrastructure bus fabric syscon node. + This property is MT7622 specific + + ieee80211-freq-limit: true + + mediatek,eeprom-data: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + EEPROM data embedded as array. + + mediatek,mtd-eeprom: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to MTD partition + - description: offset containing EEPROM data + description: + Phandle to a MTD partition + offset containing EEPROM data + + big-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: + Specify if the radio eeprom partition is written in big-endian + + mediatek,eeprom-merge-otp: + type: boolean + description: + Merge EEPROM data with OTP data. Can be used on boards where the flash + calibration data is generic and specific calibration data should be + pulled from the OTP ROM + + mediatek,disable-radar-background: + type: boolean + description: + Disable/enable radar/CAC detection running on a dedicated offchannel + chain available on some hw. + Background radar/CAC detection allows to avoid the CAC downtime + switching on a different channel during CAC detection on the selected + radar channel. + + led: + type: object + $ref: /schemas/leds/common.yaml# + additionalProperties: false + properties: + led-sources: + maxItems: 1 + + power-limits: + type: object + additionalProperties: false + patternProperties: + "^r[0-9]+": + type: object + additionalProperties: false + properties: + regdomain: + $ref: /schemas/types.yaml#/definitions/string + description: + Regdomain refers to a legal regulatory region. Different + countries define different levels of allowable transmitter + power, time that a channel can be occupied, and different + available channels + enum: + - FCC + - ETSI + - JP + + patternProperties: + "^txpower-[256]g$": + type: object + additionalProperties: false + patternProperties: + "^b[0-9]+$": + type: object + additionalProperties: false + properties: + channels: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: + Pairs of first and last channel number of the selected + band + + rates-cck: + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 4 + maxItems: 4 + description: + 4 half-dBm per-rate power limit values + + rates-ofdm: + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 8 + maxItems: 8 + description: + 8 half-dBm per-rate power limit values + + rates-mcs: + $ref: /schemas/types.yaml#/definitions/uint8-matrix + description: + Sets of per-rate power limit values for 802.11n/802.11ac + rates for multiple channel bandwidth settings. + Each set starts with the number of channel bandwidth + settings for which the rate set applies, followed by + either 8 or 10 power limit values. The order of the + channel bandwidth settings is 20, 40, 80 and 160 MHz. + maxItems: 4 + items: + minItems: 9 + maxItems: 11 + + rates-ru: + $ref: /schemas/types.yaml#/definitions/uint8-matrix + description: + Sets of per-rate power limit values for 802.11ax rates + for multiple channel bandwidth or resource unit settings. + Each set starts with the number of channel bandwidth or + resource unit settings for which the rate set applies, + followed by 12 power limit values. The order of the + channel resource unit settings is RU26, RU52, RU106, + RU242/SU20, RU484/SU40, RU996/SU80 and RU2x996/SU160. + items: + minItems: 13 + maxItems: 13 + + txs-delta: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + Half-dBm power delta for different numbers of antennas + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + pcie0 { + #address-cells = <3>; + #size-cells = <2>; + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <5000000 6000000>; + mediatek,mtd-eeprom = <&factory 0x8000>; + big-endian; + + led { + led-sources = <2>; + }; + + power-limits { + r0 { + regdomain = "FCC"; + txpower-5g { + b0 { + channels = <36 48>; + rates-ofdm = /bits/ 8 <23 23 23 23 23 23 23 23>; + rates-mcs = /bits/ 8 <1 23 23 23 23 23 23 23 23 23 23>, + /bits/ 8 <3 22 22 22 22 22 22 22 22 22 22>; + rates-ru = /bits/ 8 <3 22 22 22 22 22 22 22 22 22 22 22 22>, + /bits/ 8 <4 20 20 20 20 20 20 20 20 20 20 20 20>; + }; + b1 { + channels = <100 181>; + rates-ofdm = /bits/ 8 <14 14 14 14 14 14 14 14>; + rates-mcs = /bits/ 8 <4 14 14 14 14 14 14 14 14 14 14>; + txs-delta = <12 9 6>; + rates-ru = /bits/ 8 <7 14 14 14 14 14 14 14 14 14 14 14 14>; + }; + }; + }; + }; + }; + }; + + - | + wifi@10300000 { + compatible = "mediatek,mt7628-wmac"; + reg = <0x10300000 0x100000>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + mediatek,mtd-eeprom = <&factory 0x0>; + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + wifi@18000000 { + compatible = "mediatek,mt7622-wmac"; + reg = <0x10300000 0x100000>; + interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_LOW>; + + mediatek,infracfg = <&infracfg>; + + power-domains = <&scpsys 3>; + }; + + - | + wifi@18000000 { + compatible = "mediatek,mt7986-wmac"; + resets = <&watchdog 23>; + reset-names = "consys"; + reg = <0x18000000 0x1000000>, + <0x10003000 0x1000>, + <0x11d10000 0x1000>; + interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>; + memory-region = <&wmcpu_emi>; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml new file mode 100644 index 000000000000..60de78f1bc7b --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml @@ -0,0 +1,94 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip WILC wireless devicetree bindings + +maintainers: + - Adham Abozaeid <adham.abozaeid@microchip.com> + - Ajay Singh <ajay.kathat@microchip.com> + +description: + The wilc1000 chips can be connected via SPI or SDIO. This document + describes the binding to connect wilc devices. + +properties: + compatible: + const: microchip,wilc1000 + + reg: true + + spi-max-frequency: true + + interrupts: + maxItems: 1 + + clocks: + description: phandle to the clock connected on rtc clock line. + maxItems: 1 + + clock-names: + const: rtc + + enable-gpios: + maxItems: 1 + description: Used by wilc1000-spi to determine the GPIO line + connected to the ENABLE line. If specified, reset-gpios + must be specified as well as otherwise the driver cannot + ensure the timing required between asserting ENABLE + and deasserting RESET. This should be declared as an + active-high signal. + + reset-gpios: + maxItems: 1 + description: Used by wilc1000-spi to determine the GPIO line + connected to the RESET line. This should be declared as an + active-low signal. + +required: + - compatible + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + wifi@0 { + compatible = "microchip,wilc1000"; + spi-max-frequency = <48000000>; + reg = <0>; + interrupt-parent = <&pioC>; + interrupts = <27 0>; + clocks = <&pck1>; + clock-names = "rtc"; + enable-gpios = <&pioA 5 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pioA 6 GPIO_ACTIVE_LOW>; + }; + }; + + - | + mmc { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>; + non-removable; + vmmc-supply = <&vcc_mmc1_reg>; + vqmmc-supply = <&vcc_3v3_reg>; + bus-width = <4>; + wifi@0 { + compatible = "microchip,wilc1000"; + reg = <0>; + interrupt-parent = <&pioC>; + interrupts = <27 0>; + clocks = <&pck1>; + clock-names = "rtc"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt deleted file mode 100644 index aaaeeb5f935b..000000000000 --- a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt +++ /dev/null @@ -1,48 +0,0 @@ -* Qualcomm Atheros ath9k wireless devices - -This node provides properties for configuring the ath9k wireless device. The -node is expected to be specified as a child node of the PCI controller to -which the wireless chip is connected. - -Required properties: -- compatible: For PCI and PCIe devices this should be an identifier following - the format as defined in "PCI Bus Binding to Open Firmware" - Revision 2.1. One of the possible formats is "pciVVVV,DDDD" - where VVVV is the PCI vendor ID and DDDD is PCI device ID. - Typically QCA's PCI vendor ID 168c is used while the PCI device - ID depends on the chipset - see the following (possibly - incomplete) list: - - 0023 for AR5416 - - 0024 for AR5418 - - 0027 for AR9160 - - 0029 for AR9220 and AR9223 - - 002a for AR9280 and AR9283 - - 002b for AR9285 - - 002c for AR2427 - - 002d for AR9227 - - 002e for AR9287 - - 0030 for AR9380, AR9381 and AR9382 - - 0032 for AR9485 - - 0033 for AR9580 and AR9590 - - 0034 for AR9462 - - 0036 for AR9565 - - 0037 for AR9485 -- reg: Address and length of the register set for the device. - -Optional properties: -- qca,no-eeprom: Indicates that there is no physical EEPROM connected to the - ath9k wireless chip (in this case the calibration / - EEPROM data will be loaded from userspace using the - kernel firmware loader). - -The MAC address will be determined using the optional properties defined in -net/ethernet.txt. - -In this example, the node is defined as child node of the PCI controller: -&pci0 { - wifi@168c,002d { - compatible = "pci168c,002d"; - reg = <0x7000 0 0 0 0x1000>; - qca,no-eeprom; - }; -}; diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml new file mode 100644 index 000000000000..8cd0adbf7021 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/qca,ath9k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros ath9k wireless devices Generic Binding + +maintainers: + - Kalle Valo <kvalo@codeaurora.org> + +description: | + This node provides properties for configuring the ath9k wireless device. + The node is expected to be specified as a child node of the PCI controller + to which the wireless chip is connected. + +allOf: + - $ref: ieee80211.yaml# + +properties: + compatible: + enum: + - pci168c,0023 # AR5416 + - pci168c,0024 # AR5418 + - pci168c,0027 # AR9160 + - pci168c,0029 # AR9220 and AR9223 + - pci168c,002a # AR9280 and AR9283 + - pci168c,002b # AR9285 + - pci168c,002c # AR2427 - 802.11n bonded out + - pci168c,002d # AR9227 + - pci168c,002e # AR9287 + - pci168c,0030 # AR9380, AR9381 and AR9382 + - pci168c,0032 # AR9485 + - pci168c,0033 # AR9580 and AR9590 + - pci168c,0034 # AR9462 + - pci168c,0036 # AR9565 + - pci168c,0037 # AR1111 and AR9485 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + ieee80211-freq-limit: true + + qca,no-eeprom: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates that there is no physical EEPROM connected + + nvmem-cells: + items: + - description: Reference to an nvmem node for the MAC address + - description: Reference to an nvmem node for calibration data + + nvmem-cell-names: + items: + - const: mac-address + - const: calibration + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + pcie0 { + #address-cells = <3>; + #size-cells = <2>; + wifi@0,0 { + compatible = "pci168c,002d"; + reg = <0 0 0 0 0>; + interrupts = <3>; + qca,no-eeprom; + }; + }; + - | + pci0 { + #address-cells = <3>; + #size-cells = <2>; + wifi@0,11 { + compatible = "pci168c,0029"; + reg = <0x8800 0 0 0 0>; + nvmem-cells = <&macaddr_art_c>, <&cal_art_1000>; + nvmem-cell-names = "mac-address", "calibration"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index ae661e65354e..b61c2d5a0ff7 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -50,7 +50,7 @@ Optional properties: entry in clock-names. - clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref", "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and - "cxo_ref_clk_pin" for "qcom,wcn3990-wifi" + "cxo_ref_clk_pin" and optionally "qdss" for "qcom,wcn3990-wifi" compatible target. - qcom,msi_addr: MSI interrupt address. - qcom,msi_base: Base value to add before writing MSI data into @@ -65,7 +65,8 @@ Optional properties: the length can vary between hw versions. - <supply-name>-supply: handle to the regulator device tree node optional "supply-name" are "vdd-0.8-cx-mx", - "vdd-1.8-xo", "vdd-1.3-rfa" and "vdd-3.3-ch0". + "vdd-1.8-xo", "vdd-1.3-rfa", "vdd-3.3-ch0", + and "vdd-3.3-ch1". - memory-region: Usage: optional Value type: <phandle> @@ -81,6 +82,31 @@ Optional properties: Definition: Name of external front end module used. Some valid FEM names for example: "microsemi-lx5586", "sky85703-11" and "sky85803" etc. +- qcom,snoc-host-cap-8bit-quirk: + Usage: Optional + Value type: <empty> + Definition: Quirk specifying that the firmware expects the 8bit version + of the host capability QMI request +- qcom,xo-cal-data: xo cal offset to be configured in xo trim register. + +- qcom,msa-fixed-perm: Boolean context flag to disable SCM call for statically + mapped msa region. + +- qcom,coexist-support : should contain eithr "0" or "1" to indicate coex + support by the hardware. +- qcom,coexist-gpio-pin : gpio pin number information to support coex + which will be used by wifi firmware. + +* Subnodes +The ath10k wifi node can contain one optional firmware subnode. +Firmware subnode is needed when the platform does not have TustZone. +The firmware subnode must have: + +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + Example (to supply PCI based wifi block details): @@ -150,6 +176,8 @@ wifi0: wifi@a000000 { qcom,msi_addr = <0x0b006040>; qcom,msi_base = <0x40>; qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; + qcom,coexist-support = <1>; + qcom,coexist-gpio-pin = <0x33>; }; Example (to supply wcn3990 SoC wifi block details): @@ -177,6 +205,11 @@ wifi@18000000 { vdd-1.8-xo-supply = <&vreg_l7a_1p8>; vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + vdd-3.3-ch1-supply = <&vreg_l26a_3p3>; memory-region = <&wifi_msa_mem>; iommus = <&apps_smmu 0x0040 0x1>; + qcom,msa-fixed-perm; + wifi-firmware { + iommus = <&apps_iommu 0xc22 0x1>; + }; }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml new file mode 100644 index 000000000000..8c01fdba134b --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml @@ -0,0 +1,454 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved. + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/qcom,ath11k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies ath11k wireless devices Generic Binding + +maintainers: + - Kalle Valo <kvalo@codeaurora.org> + +description: | + These are dt entries for Qualcomm Technologies, Inc. IEEE 802.11ax + devices, for example like AHB based IPQ8074. + +properties: + compatible: + enum: + - qcom,ipq8074-wifi + - qcom,ipq6018-wifi + - qcom,wcn6750-wifi + + reg: + maxItems: 1 + + interrupts: + minItems: 32 + maxItems: 52 + + interrupt-names: + maxItems: 52 + + qcom,rproc: + $ref: /schemas/types.yaml#/definitions/phandle + description: + DT entry of q6v5-wcss remoteproc driver. + Phandle to a node that can contain the following properties + * compatible + * reg + * reg-names + + qcom,ath11k-calibration-variant: + $ref: /schemas/types.yaml#/definitions/string + description: + string to uniquely identify variant of the calibration data in the + board-2.bin for designs with colliding bus and device specific ids + + memory-region: + minItems: 1 + maxItems: 2 + description: + phandle to a node describing reserved memory (System RAM memory) + used by ath11k firmware (see bindings/reserved-memory/reserved-memory.txt) + + iommus: + minItems: 1 + maxItems: 2 + + wifi-firmware: + type: object + description: | + WCN6750 wifi node can contain one optional firmware subnode. + Firmware subnode is needed when the platform does not have Trustzone. + required: + - iommus + +required: + - compatible + - reg + - interrupts + - qcom,rproc + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq8074-wifi + - qcom,ipq6018-wifi + then: + properties: + interrupts: + items: + - description: misc-pulse1 interrupt events + - description: misc-latch interrupt events + - description: sw exception interrupt events + - description: watchdog interrupt events + - description: interrupt event for ring CE0 + - description: interrupt event for ring CE1 + - description: interrupt event for ring CE2 + - description: interrupt event for ring CE3 + - description: interrupt event for ring CE4 + - description: interrupt event for ring CE5 + - description: interrupt event for ring CE6 + - description: interrupt event for ring CE7 + - description: interrupt event for ring CE8 + - description: interrupt event for ring CE9 + - description: interrupt event for ring CE10 + - description: interrupt event for ring CE11 + - description: interrupt event for ring host2wbm-desc-feed + - description: interrupt event for ring host2reo-re-injection + - description: interrupt event for ring host2reo-command + - description: interrupt event for ring host2rxdma-monitor-ring3 + - description: interrupt event for ring host2rxdma-monitor-ring2 + - description: interrupt event for ring host2rxdma-monitor-ring1 + - description: interrupt event for ring reo2ost-exception + - description: interrupt event for ring wbm2host-rx-release + - description: interrupt event for ring reo2host-status + - description: interrupt event for ring reo2host-destination-ring4 + - description: interrupt event for ring reo2host-destination-ring3 + - description: interrupt event for ring reo2host-destination-ring2 + - description: interrupt event for ring reo2host-destination-ring1 + - description: interrupt event for ring rxdma2host-monitor-destination-mac3 + - description: interrupt event for ring rxdma2host-monitor-destination-mac2 + - description: interrupt event for ring rxdma2host-monitor-destination-mac1 + - description: interrupt event for ring ppdu-end-interrupts-mac3 + - description: interrupt event for ring ppdu-end-interrupts-mac2 + - description: interrupt event for ring ppdu-end-interrupts-mac1 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac3 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac2 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac1 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac3 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac2 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac1 + - description: interrupt event for ring rxdma2host-destination-ring-mac3 + - description: interrupt event for ring rxdma2host-destination-ring-mac2 + - description: interrupt event for ring rxdma2host-destination-ring-mac1 + - description: interrupt event for ring host2tcl-input-ring4 + - description: interrupt event for ring host2tcl-input-ring3 + - description: interrupt event for ring host2tcl-input-ring2 + - description: interrupt event for ring host2tcl-input-ring1 + - description: interrupt event for ring wbm2host-tx-completions-ring3 + - description: interrupt event for ring wbm2host-tx-completions-ring2 + - description: interrupt event for ring wbm2host-tx-completions-ring1 + - description: interrupt event for ring tcl2host-status-ring + interrupt-names: + items: + - const: misc-pulse1 + - const: misc-latch + - const: sw-exception + - const: watchdog + - const: ce0 + - const: ce1 + - const: ce2 + - const: ce3 + - const: ce4 + - const: ce5 + - const: ce6 + - const: ce7 + - const: ce8 + - const: ce9 + - const: ce10 + - const: ce11 + - const: host2wbm-desc-feed + - const: host2reo-re-injection + - const: host2reo-command + - const: host2rxdma-monitor-ring3 + - const: host2rxdma-monitor-ring2 + - const: host2rxdma-monitor-ring1 + - const: reo2ost-exception + - const: wbm2host-rx-release + - const: reo2host-status + - const: reo2host-destination-ring4 + - const: reo2host-destination-ring3 + - const: reo2host-destination-ring2 + - const: reo2host-destination-ring1 + - const: rxdma2host-monitor-destination-mac3 + - const: rxdma2host-monitor-destination-mac2 + - const: rxdma2host-monitor-destination-mac1 + - const: ppdu-end-interrupts-mac3 + - const: ppdu-end-interrupts-mac2 + - const: ppdu-end-interrupts-mac1 + - const: rxdma2host-monitor-status-ring-mac3 + - const: rxdma2host-monitor-status-ring-mac2 + - const: rxdma2host-monitor-status-ring-mac1 + - const: host2rxdma-host-buf-ring-mac3 + - const: host2rxdma-host-buf-ring-mac2 + - const: host2rxdma-host-buf-ring-mac1 + - const: rxdma2host-destination-ring-mac3 + - const: rxdma2host-destination-ring-mac2 + - const: rxdma2host-destination-ring-mac1 + - const: host2tcl-input-ring4 + - const: host2tcl-input-ring3 + - const: host2tcl-input-ring2 + - const: host2tcl-input-ring1 + - const: wbm2host-tx-completions-ring3 + - const: wbm2host-tx-completions-ring2 + - const: wbm2host-tx-completions-ring1 + - const: tcl2host-status-ring + + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq8074-wifi + - qcom,ipq6018-wifi + then: + required: + - interrupt-names + + - if: + properties: + compatible: + contains: + enum: + - qcom,wcn6750-wifi + then: + properties: + interrupts: + items: + - description: interrupt event for ring CE1 + - description: interrupt event for ring CE2 + - description: interrupt event for ring CE3 + - description: interrupt event for ring CE4 + - description: interrupt event for ring CE5 + - description: interrupt event for ring CE6 + - description: interrupt event for ring CE7 + - description: interrupt event for ring CE8 + - description: interrupt event for ring CE9 + - description: interrupt event for ring CE10 + - description: interrupt event for ring DP1 + - description: interrupt event for ring DP2 + - description: interrupt event for ring DP3 + - description: interrupt event for ring DP4 + - description: interrupt event for ring DP5 + - description: interrupt event for ring DP6 + - description: interrupt event for ring DP7 + - description: interrupt event for ring DP8 + - description: interrupt event for ring DP9 + - description: interrupt event for ring DP10 + - description: interrupt event for ring DP11 + - description: interrupt event for ring DP12 + - description: interrupt event for ring DP13 + - description: interrupt event for ring DP14 + - description: interrupt event for ring DP15 + - description: interrupt event for ring DP16 + - description: interrupt event for ring DP17 + - description: interrupt event for ring DP18 + - description: interrupt event for ring DP19 + - description: interrupt event for ring DP20 + - description: interrupt event for ring DP21 + - description: interrupt event for ring DP22 + +examples: + - | + + q6v5_wcss: q6v5_wcss@CD00000 { + compatible = "qcom,ipq8074-wcss-pil"; + reg = <0xCD00000 0x4040>, + <0x4AB000 0x20>; + reg-names = "qdsp6", + "rmb"; + }; + + wifi0: wifi@c000000 { + compatible = "qcom,ipq8074-wifi"; + reg = <0xc000000 0x2000000>; + interrupts = <0 320 1>, + <0 319 1>, + <0 318 1>, + <0 317 1>, + <0 316 1>, + <0 315 1>, + <0 314 1>, + <0 311 1>, + <0 310 1>, + <0 411 1>, + <0 410 1>, + <0 40 1>, + <0 39 1>, + <0 302 1>, + <0 301 1>, + <0 37 1>, + <0 36 1>, + <0 296 1>, + <0 295 1>, + <0 294 1>, + <0 293 1>, + <0 292 1>, + <0 291 1>, + <0 290 1>, + <0 289 1>, + <0 288 1>, + <0 239 1>, + <0 236 1>, + <0 235 1>, + <0 234 1>, + <0 233 1>, + <0 232 1>, + <0 231 1>, + <0 230 1>, + <0 229 1>, + <0 228 1>, + <0 224 1>, + <0 223 1>, + <0 203 1>, + <0 183 1>, + <0 180 1>, + <0 179 1>, + <0 178 1>, + <0 177 1>, + <0 176 1>, + <0 163 1>, + <0 162 1>, + <0 160 1>, + <0 159 1>, + <0 158 1>, + <0 157 1>, + <0 156 1>; + interrupt-names = "misc-pulse1", + "misc-latch", + "sw-exception", + "watchdog", + "ce0", + "ce1", + "ce2", + "ce3", + "ce4", + "ce5", + "ce6", + "ce7", + "ce8", + "ce9", + "ce10", + "ce11", + "host2wbm-desc-feed", + "host2reo-re-injection", + "host2reo-command", + "host2rxdma-monitor-ring3", + "host2rxdma-monitor-ring2", + "host2rxdma-monitor-ring1", + "reo2ost-exception", + "wbm2host-rx-release", + "reo2host-status", + "reo2host-destination-ring4", + "reo2host-destination-ring3", + "reo2host-destination-ring2", + "reo2host-destination-ring1", + "rxdma2host-monitor-destination-mac3", + "rxdma2host-monitor-destination-mac2", + "rxdma2host-monitor-destination-mac1", + "ppdu-end-interrupts-mac3", + "ppdu-end-interrupts-mac2", + "ppdu-end-interrupts-mac1", + "rxdma2host-monitor-status-ring-mac3", + "rxdma2host-monitor-status-ring-mac2", + "rxdma2host-monitor-status-ring-mac1", + "host2rxdma-host-buf-ring-mac3", + "host2rxdma-host-buf-ring-mac2", + "host2rxdma-host-buf-ring-mac1", + "rxdma2host-destination-ring-mac3", + "rxdma2host-destination-ring-mac2", + "rxdma2host-destination-ring-mac1", + "host2tcl-input-ring4", + "host2tcl-input-ring3", + "host2tcl-input-ring2", + "host2tcl-input-ring1", + "wbm2host-tx-completions-ring3", + "wbm2host-tx-completions-ring2", + "wbm2host-tx-completions-ring1", + "tcl2host-status-ring"; + qcom,rproc = <&q6v5_wcss>; + }; + + - | + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + + qcn9074_0: qcn9074_0@51100000 { + no-map; + reg = <0x0 0x51100000 0x0 0x03500000>; + }; + }; + + pci { + pcie0 { + #size-cells = <2>; + #address-cells = <3>; + + wifi_0: wifi@0 { + reg = <0 0 0 0 0>; + memory-region = <&qcn9074_0>; + }; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + + wlan_ce_mem: memory@4cd000 { + no-map; + reg = <0x0 0x004cd000 0x0 0x1000>; + }; + + wlan_fw_mem: memory@80c00000 { + no-map; + reg = <0x0 0x80c00000 0x0 0xc00000>; + }; + }; + + wifi: wifi@17a10040 { + compatible = "qcom,wcn6750-wifi"; + reg = <0x17a10040 0x0>; + iommus = <&apps_smmu 0x1c00 0x1>; + interrupts = <GIC_SPI 768 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 769 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 770 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 771 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 772 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 773 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 774 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 775 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 776 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 777 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 778 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 779 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 780 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 781 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 782 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 783 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 784 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 785 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 786 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 787 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 788 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 789 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 790 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 791 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 792 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 793 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 794 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 795 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 796 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 797 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 798 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 799 IRQ_TYPE_EDGE_RISING>; + qcom,rproc = <&remoteproc_wpss>; + memory-region = <&wlan_fw_mem>, <&wlan_ce_mem>; + wifi-firmware { + iommus = <&apps_smmu 0x1c02 0x1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml new file mode 100644 index 000000000000..76199a67d628 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml @@ -0,0 +1,138 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020, Silicon Laboratories, Inc. +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silicon Labs WFxxx devicetree bindings + +maintainers: + - Jérôme Pouiller <jerome.pouiller@silabs.com> + +description: > + Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device + from the WFxxx series is the WF200 described here: + https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf + + The WF200 can be connected via SPI or via SDIO. + + For SDIO: + + Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is + sufficient for the SDIO devices). + + It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without + it, you may encounter issues during reboot. The mmc-pwrseq should be + compatible with mmc-pwrseq-simple. Please consult + Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml for more + information. + + For SPI: + + In add of the properties below, please consult + Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI + related properties. + +properties: + compatible: + items: + - enum: + - prt,prtt1c-wfm200 # Protonic PRTT1C Board + - silabs,brd4001a # WGM160P Evaluation Board + - silabs,brd8022a # WF200 Evaluation Board + - silabs,brd8023a # WFM200 Evaluation Board + - const: silabs,wf200 # Chip alone without antenna + + reg: + description: + When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is + the chip select address of the device as defined in the SPI devices + bindings. + maxItems: 1 + + spi-max-frequency: true + + interrupts: + description: The interrupt line. Should be IRQ_TYPE_EDGE_RISING. When SPI is + used, this property is required. When SDIO is used, the "in-band" + interrupt provided by the SDIO bus is used unless an interrupt is defined + in the Device Tree. + maxItems: 1 + + reset-gpios: + description: (SPI only) Phandle of gpio that will be used to reset chip + during probe. Without this property, you may encounter issues with warm + boot. + + For SDIO, the reset gpio should declared using a mmc-pwrseq. + maxItems: 1 + + wakeup-gpios: + description: Phandle of gpio that will be used to wake-up chip. Without this + property, driver will disable most of power saving features. + maxItems: 1 + + silabs,antenna-config-file: + $ref: /schemas/types.yaml#/definitions/string + description: Use an alternative file for antenna configuration (aka + "Platform Data Set" in Silabs jargon). Default depends of "compatible" + string. For "silabs,wf200", the default is 'wf200.pds'. + + local-mac-address: true + + mac-address: true + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + wifi@0 { + compatible = "silabs,brd8022a", "silabs,wf200"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_irq &wfx_gpios>; + reg = <0>; + interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>; + wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + spi-max-frequency = <42000000>; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + wfx_pwrseq: wfx_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_reset>; + reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + mmc { + mmc-pwrseq = <&wfx_pwrseq>; + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "silabs,brd8022a", "silabs,wf200"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_wakeup>; + reg = <1>; + wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt index bb2fcde6f7ff..88fd28d15eac 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt @@ -9,11 +9,12 @@ Required properties: - spi-max-frequency : Maximum SPI clocking speed of device in Hz - interrupts : Should contain interrupt line - vio-supply : phandle to regulator providing VIO -- ti,power-gpio : GPIO connected to chip's PMEN pin Optional properties: - ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which provides configuration data (calibration, MAC, ...) +- ti,power-gpio : GPIO connected to chip's PMEN pin if operated in + SPI mode - Please consult Documentation/devicetree/bindings/spi/spi-bus.txt for optional SPI connection related properties, @@ -35,3 +36,29 @@ Examples: ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */ }; }; + +&mmc3 { + vmmc-supply = <&wlan_en>; + + bus-width = <4>; + non-removable; + ti,non-removable; + cap-power-off-card; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins>; + + #address-cells = <1>; + #size-cells = <0>; + + wlan: wifi@1 { + compatible = "ti,wl1251"; + + reg = <1>; + + interrupt-parent = <&gpio1>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_21 */ + + ti,wl1251-has-eeprom; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt deleted file mode 100644 index cb5c9e1569ca..000000000000 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt +++ /dev/null @@ -1,57 +0,0 @@ -* Texas Instruments wl12xx/wl18xx wireless lan controller - -The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This -document describes the binding for the SPI connected chip. - -Required properties: -- compatible : Should be one of the following: - * "ti,wl1271" - * "ti,wl1273" - * "ti,wl1281" - * "ti,wl1283" - * "ti,wl1801" - * "ti,wl1805" - * "ti,wl1807" - * "ti,wl1831" - * "ti,wl1835" - * "ti,wl1837" -- reg : Chip select address of device -- spi-max-frequency : Maximum SPI clocking speed of device in Hz -- interrupts : Should contain parameters for 1 interrupt line. -- vwlan-supply : Point the node of the regulator that powers/enable the - wl12xx/wl18xx chip - -Optional properties: -- ref-clock-frequency : Reference clock frequency (should be set for wl12xx) -- clock-xtal : boolean, clock is generated from XTAL - -- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt - for optional SPI connection related properties, - -Examples: - -For wl12xx family: -&spi1 { - wlcore: wlcore@1 { - compatible = "ti,wl1271"; - reg = <1>; - spi-max-frequency = <48000000>; - interrupt-parent = <&gpio3>; - interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; - vwlan-supply = <&vwlan_fixed>; - clock-xtal; - ref-clock-frequency = <38400000>; - }; -}; - -For wl18xx family: -&spi0 { - wlcore: wlcore@0 { - compatible = "ti,wl1835"; - reg = <0>; - spi-max-frequency = <48000000>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_EDGE_RISING>; - vwlan-supply = <&vwlan_fixed>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt deleted file mode 100644 index 9306c4dadd46..000000000000 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt +++ /dev/null @@ -1,45 +0,0 @@ -TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices - -This node provides properties for controlling the wilink wireless device. The -node is expected to be specified as a child node to the SDIO controller that -connects the device to the system. - -Required properties: - - compatible: should be one of the following: - * "ti,wl1271" - * "ti,wl1273" - * "ti,wl1281" - * "ti,wl1283" - * "ti,wl1285" - * "ti,wl1801" - * "ti,wl1805" - * "ti,wl1807" - * "ti,wl1831" - * "ti,wl1835" - * "ti,wl1837" - - interrupts : specifies attributes for the out-of-band interrupt. - -Optional properties: - - ref-clock-frequency : ref clock frequency in Hz - - tcxo-clock-frequency : tcxo clock frequency in Hz - -Note: the *-clock-frequency properties assume internal clocks. In case of external -clock, new bindings (for parsing the clock nodes) have to be added. - -Example: - -&mmc3 { - vmmc-supply = <&wlan_en_reg>; - bus-width = <4>; - cap-power-off-card; - keep-power-in-suspend; - - #address-cells = <1>; - #size-cells = <0>; - wlcore: wlcore@2 { - compatible = "ti,wl1835"; - reg = <2>; - interrupt-parent = <&gpio0>; - interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml new file mode 100644 index 000000000000..d68bb2ec1f7e --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml @@ -0,0 +1,136 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/ti,wlcore.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments Wilink 6/7/8 (wl12xx/wl18xx) Wireless LAN Controller + +maintainers: + - Tony Lindgren <tony@atomide.com> + +description: + The wl12xx/wl18xx chips can be connected via SPI or via SDIO. + Note that the *-clock-frequency properties assume internal clocks. In case + of external clocks, new bindings (for parsing the clock nodes) have to be + added. + +properties: + compatible: + enum: + - ti,wl1271 + - ti,wl1273 + - ti,wl1281 + - ti,wl1283 + - ti,wl1285 + - ti,wl1801 + - ti,wl1805 + - ti,wl1807 + - ti,wl1831 + - ti,wl1835 + - ti,wl1837 + + reg: + maxItems: 1 + description: + This is required when connected via SPI, and optional when connected via + SDIO. + + spi-max-frequency: true + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + items: + - const: irq + - const: wakeup + + vwlan-supply: + description: + Points to the node of the regulator that powers/enable the wl12xx/wl18xx + chip. This is required when connected via SPI. + + + ref-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Reference clock frequency. + + tcxo-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: TCXO clock frequency. + + clock-xtal: + $ref: /schemas/types.yaml#/definitions/flag + description: Indicates that the clock is generated from XTAL. + +required: + - compatible + - interrupts + +if: + properties: + compatible: + contains: + enum: + - ti,wl1271 + - ti,wl1273 + - ti,wl1281 + - ti,wl1283 +then: + required: + - ref-clock-frequency + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + // For wl12xx family: + spi1 { + #address-cells = <1>; + #size-cells = <0>; + + wlcore1: wlcore@1 { + compatible = "ti,wl1271"; + reg = <1>; + spi-max-frequency = <48000000>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; + vwlan-supply = <&vwlan_fixed>; + clock-xtal; + ref-clock-frequency = <38400000>; + }; + }; + + // For wl18xx family: + spi2 { + #address-cells = <1>; + #size-cells = <0>; + + wlcore2: wlcore@0 { + compatible = "ti,wl1835"; + reg = <0>; + spi-max-frequency = <48000000>; + interrupts = <27 IRQ_TYPE_EDGE_RISING>; + vwlan-supply = <&vwlan_fixed>; + }; + }; + + // SDIO example: + mmc3 { + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + + wlcore3: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; + }; |