Merge tag 'pwm/for-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm updates from Thierry Reding:
 "Not a lot going on this cycle.

  There's some more cleanup going on and new driver support that was not
  quite ready in time for v4.21-rc1, but here are a few fixes and
  improvements that are good to go.

  The Kona PWM driver can now be built on the Cygnus architecture and
  the i.MX driver gained support for hardware readback. Some small fixes
  are provided for the clks711x and lpc18xx-sct drivers.

  Finally, to round things off some drivers are switched to SPDX license
  identifiers"

* tag 'pwm/for-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  dt-bindings: pwm: rcar: Add r8a774c0 support
  pwm: imx: Add ipg clock operation
  pwm: clps711x: Switch to SPDX identifier
  pwm: clps711x: Fix period calculation
  pwm: bcm2835: Switch to SPDX identifier
  pwm: Enable Kona PWM to be built for the Cygnus architecture
  pwm: Drop legacy wrapper for changing polarity
  pwm: imx: Implement get_state() function for hardware readout
  pwm: imx: Use bitops and bitfield macros to define register values
  pwm: imx: Sort include files
  pwm: lpc18xx-sct: Don't reconfigure PWM in .request and .free

1 files changed, 0 insertions, 42 deletions

diff --git a/include/linux/pwm.h b/include/linux/pwm.h
index 56518adc31dd..d5199b507d79 100644
--- a/include/linux/pwm.h
+++ b/include/linux/pwm.h
@@ -349,42 +349,6 @@ static inline int pwm_config(struct pwm_device *pwm, int duty_ns,
 }
 
 /**
- * pwm_set_polarity() - configure the polarity of a PWM signal
- * @pwm: PWM device
- * @polarity: new polarity of the PWM signal
- *
- * Note that the polarity cannot be configured while the PWM device is
- * enabled.
- *
- * Returns: 0 on success or a negative error code on failure.
- */
-static inline int pwm_set_polarity(struct pwm_device *pwm,
-				   enum pwm_polarity polarity)
-{
-	struct pwm_state state;
-
-	if (!pwm)
-		return -EINVAL;
-
-	pwm_get_state(pwm, &state);
-	if (state.polarity == polarity)
-		return 0;
-
-	/*
-	 * Changing the polarity of a running PWM without adjusting the
-	 * dutycycle/period value is a bit risky (can introduce glitches).
-	 * Return -EBUSY in this case.
-	 * Note that this is allowed when using pwm_apply_state() because
-	 * the user specifies all the parameters.
-	 */
-	if (state.enabled)
-		return -EBUSY;
-
-	state.polarity = polarity;
-	return pwm_apply_state(pwm, &state);
-}
-
-/**
  * pwm_enable() - start a PWM output toggling
  * @pwm: PWM device
  *
@@ -483,12 +447,6 @@ static inline int pwm_capture(struct pwm_device *pwm,
 	return -EINVAL;
 }
 
-static inline int pwm_set_polarity(struct pwm_device *pwm,
-				   enum pwm_polarity polarity)
-{
-	return -ENOTSUPP;
-}
-
 static inline int pwm_enable(struct pwm_device *pwm)
 {
 	return -EINVAL;