| Age | Commit message (Collapse) | Author |
|---|
|
Many OMAP2+ DTS are not using the defined constants to express
the GPIO polarity. Replace these so the DTS are easier to read.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
|
|
Replace all the pdata-quirks for setting wl12xx/wl18xx
platform data with proper DT definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4/5 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the WUGEN HW block, kernels with this patch applied
won't have any suspend-resume facility when booted with old DTs,
and old kernels with updated DTs won't even boot.
On a platform with this patch applied, the system looks like
this:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 0 0 WUGEN 37 gp_timer
19: 233799 155916 GIC 27 arch_timer
23: 0 0 WUGEN 9 l3-dbg-irq
24: 1 0 WUGEN 10 l3-app-irq
27: 282 0 WUGEN 13 omap-dma-engine
44: 0 0 4ae10000.gpio 13 DMA
294: 0 0 WUGEN 20 gpmc
297: 506 0 WUGEN 56 48070000.i2c
298: 0 0 WUGEN 57 48072000.i2c
299: 0 0 WUGEN 61 48060000.i2c
300: 0 0 WUGEN 62 4807a000.i2c
301: 8 0 WUGEN 60 4807c000.i2c
308: 2439 0 WUGEN 74 OMAP UART2
312: 362 0 WUGEN 83 mmc2
313: 502 0 WUGEN 86 mmc0
314: 13 0 WUGEN 94 mmc1
350: 0 0 PRCM pinctrl, pinctrl
406: 35155709 0 GIC 109 ehci_hcd:usb1
407: 0 0 WUGEN 7 palmas
409: 0 0 WUGEN 119 twl6040
410: 0 0 twl6040 5 twl6040_irq_ready
411: 0 0 twl6040 0 twl6040_irq_th
IPI0: 0 1 CPU wakeup interrupts
IPI1: 0 0 Timer broadcast interrupts
IPI2: 95334 902334 Rescheduling interrupts
IPI3: 0 0 Function call interrupts
IPI4: 479 648 Single function call interrupts
IPI5: 0 0 CPU stop interrupts
IPI6: 0 0 IRQ work interrupts
IPI7: 0 0 completion interrupts
Err: 0
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Currently we claim that omap4-panda and omap4-panda-es are essentially
the same, but they are not since PandaBoard-ES uses OMAP4460 and
PandaBoard uses OMAP4430.
So, split the common definition and make the model name available.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've had deeper idle states working on omaps for few years now,
but only in the legacy mode. When booted with device tree, the
wake-up events did not have a chance to work until commit
3e6cee1786a1 (pinctrl: single: Add support for wake-up interrupts)
that recently got merged. In addition to that we also needed commit
79d9701559a9 (of/irq: create interrupts-extended property) and
9ec36cafe43b (of/irq: do irq resolution in platform_get_irq) that
are now also merged.
So let's fix the wake-up events for some selected omaps so devices
booted in device tree mode won't just hang if deeper power states
are enabled, and so systems can wake up from suspend to the serial
port event.
Note that there's no longer need to specify the wake-up bit in
the pinctrl settings, the request_irq on the wake-up pin takes
care of that.
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: updated comments, added board LDP]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add DT data for OMAP4 Pandaboard. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.
Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Attach the pinctrl nodes to their respective device node:
mcbsp1, mcpdm and twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
New u-boot versions no longer set the pinmuxing for Panda's DPI output,
and the muxing has to be done in the .dts file.
Add pinmuxing for DPI and TFP410. Without these, the DVI output on Panda
does not work with recent u-boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
dtsi file
The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.
Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Commit b42b9181 (ARM: OMAP2+: Remove board-omap4panda.c)
removed legacy booting in favor of device tree based booting
for pandaboard. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.
The legacy muxing was setting pulls for GPIO 48 and 49, so let's
keep that behaviour for now to avoid further regressions for
BT and FM. Also input logic was enabled for MMC CLK line, but
I've verified that the input logic we don't need enabled for
CLK line as it's not bidirectional.
Also, we want to use non-removable instead of ti,non-removable
as the ti,non-removable also sets no_regulator_off_init which
is really not what we want as then wl12xx won't get powered
up and down which is needed for resetting it.
Note that looks like the WLAN interface fails to come up after
a warm reset, but that most likely was also happening with
the legacy booting and needs a separate fix.
Cc: Paolo Pisati <p.pisati@gmail.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
On Panda the +5V supply for DVI EDID is supplied by the
same regulator that poweres the USB Hub. Currently, the
DSS/DVI subsystem doesn't know how to manage this regulator
and so DVI EDID reads will fail if USB Hub is not enabled.
As a temporary fix we keep this regulator permanently enabled
on boot. This fixes the DVI EDID read problem.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for the USB host
pins.
HACK: The reset control need to be replaced with the proper
gpio-controlled reset driver as soon it will be merged [1].
[1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
Signed-off-by: Roger Quadros <rogerq@ti.com>
[benoit.cousson@linaro.org: Add disclaimer about the reset control
inside changelog and code]
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Update the dt property ti,audpwron-gpio to use the
gpio macro definition for GPIO_ACTIVE_HIGH.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es
are different.
A1-A3 = gpio_wk7
ES = gpio_110
There is no change to LED D2
Abstract away the pinmux and the LED definitions for the two boards into
the respective DTS files.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Use the constants defined in include/dt-bindings/interrupt-controller/
to enhance readability.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Earlier commits ensured proper muxing of pins related to proper
TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure
sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM:
OMAP4: TWL: mux sys_drm_msecure as output for PMIC).
However these only fixed legacy boot and not DT boot. For DT boot,
the default mux values need to be set properly in DT.
Special thanks to Nishanth Menon for the review and catching some
major flaws in earlier versions.
Tested on OMAP4430/Panda and OMAP4460/Panda-ES.
Cc: Nishanth Menon <nm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
[benoit.cousson@linaro.org: Slightly change the subject to align
board name with file name]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
PandaBoard, PandaBoard-A4 revisions use OMAP4430.
PandaBoard-ES version of the board uses OMAP4460.
Move the original panda dts file into a common dtsi used by all panda
variants. This allows us to introduce SoC variation for PandaBoard ES
without impacting other PandaBoard versions that are supported.
As part of this change, since OMAP4460 adds on to OMAP4430, add
omap4.dtsi to omap4460.dtsi.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
