i2c: mxs: Set I2C timing registers for mxs-i2c

This patch configures the I2C bus timing registers according
to information passed via DT. Currently, 100kHz and 400kHz
modes are supported.

The TIMING2 register value is wrong in the documentation for
i.MX28! This was found and fixed by:
  Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

1 files changed, 66 insertions, 0 deletions

diff --git a/drivers/i2c/busses/i2c-mxs.c b/drivers/i2c/busses/i2c-mxs.c
index 02ce1faeeeef..088c5c1ed17d 100644
--- a/drivers/i2c/busses/i2c-mxs.c
+++ b/drivers/i2c/busses/i2c-mxs.c
@@ -46,6 +46,10 @@
 #define MXS_I2C_CTRL0_DIRECTION			0x00010000
 #define MXS_I2C_CTRL0_XFER_COUNT(v)		((v) & 0x0000FFFF)
 
+#define MXS_I2C_TIMING0		(0x10)
+#define MXS_I2C_TIMING1		(0x20)
+#define MXS_I2C_TIMING2		(0x30)
+
 #define MXS_I2C_CTRL1		(0x40)
 #define MXS_I2C_CTRL1_SET	(0x44)
 #define MXS_I2C_CTRL1_CLR	(0x48)
@@ -97,6 +101,35 @@
 #define MXS_CMD_I2C_READ	(MXS_I2C_CTRL0_SEND_NAK_ON_LAST | \
 				 MXS_I2C_CTRL0_MASTER_MODE)
 
+struct mxs_i2c_speed_config {
+	uint32_t	timing0;
+	uint32_t	timing1;
+	uint32_t	timing2;
+};
+
+/*
+ * Timing values for the default 24MHz clock supplied into the i2c block.
+ *
+ * The bus can operate at 95kHz or at 400kHz with the following timing
+ * register configurations. The 100kHz mode isn't present because it's
+ * values are not stated in the i.MX233/i.MX28 datasheet. The 95kHz mode
+ * shall be close enough replacement. Therefore when the bus is configured
+ * for 100kHz operation, 95kHz timing settings are actually loaded.
+ *
+ * For details, see i.MX233 [25.4.2 - 25.4.4] and i.MX28 [27.5.2 - 27.5.4].
+ */
+static const struct mxs_i2c_speed_config mxs_i2c_95kHz_config = {
+	.timing0	= 0x00780030,
+	.timing1	= 0x00800030,
+	.timing2	= 0x00300030,
+};
+
+static const struct mxs_i2c_speed_config mxs_i2c_400kHz_config = {
+	.timing0	= 0x000f0007,
+	.timing1	= 0x001f000f,
+	.timing2	= 0x00300030,
+};
+
 /**
  * struct mxs_i2c_dev - per device, private MXS-I2C data
  *
@@ -112,11 +145,17 @@ struct mxs_i2c_dev {
 	struct completion cmd_complete;
 	u32 cmd_err;
 	struct i2c_adapter adapter;
+	const struct mxs_i2c_speed_config *speed;
 };
 
 static void mxs_i2c_reset(struct mxs_i2c_dev *i2c)
 {
 	stmp_reset_block(i2c->regs);
+
+	writel(i2c->speed->timing0, i2c->regs + MXS_I2C_TIMING0);
+	writel(i2c->speed->timing1, i2c->regs + MXS_I2C_TIMING1);
+	writel(i2c->speed->timing2, i2c->regs + MXS_I2C_TIMING2);
+
 	writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_SET);
 	writel(MXS_I2C_QUEUECTRL_PIO_QUEUE_MODE,
 			i2c->regs + MXS_I2C_QUEUECTRL_SET);
@@ -319,6 +358,28 @@ static const struct i2c_algorithm mxs_i2c_algo = {
 	.functionality = mxs_i2c_func,
 };
 
+static int mxs_i2c_get_ofdata(struct mxs_i2c_dev *i2c)
+{
+	uint32_t speed;
+	struct device *dev = i2c->dev;
+	struct device_node *node = dev->of_node;
+	int ret;
+
+	if (!node)
+		return -EINVAL;
+
+	i2c->speed = &mxs_i2c_95kHz_config;
+	ret = of_property_read_u32(node, "clock-frequency", &speed);
+	if (ret)
+		dev_warn(dev, "No I2C speed selected, using 100kHz\n");
+	else if (speed == 400000)
+		i2c->speed = &mxs_i2c_400kHz_config;
+	else if (speed != 100000)
+		dev_warn(dev, "Unsupported I2C speed selected, using 100kHz\n");
+
+	return 0;
+}
+
 static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -358,6 +419,11 @@ static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 		return err;
 
 	i2c->dev = dev;
+
+	err = mxs_i2c_get_ofdata(i2c);
+	if (err)
+		return err;
+
 	platform_set_drvdata(pdev, i2c);
 
 	/* Do reset to enforce correct startup after pinmuxing */