aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/arm/configs/kirkwood_defconfig20
-rw-r--r--arch/arm/mach-kirkwood/Kconfig6
-rw-r--r--arch/arm/mach-kirkwood/Makefile1
-rw-r--r--arch/arm/mach-kirkwood/common.c40
-rw-r--r--arch/arm/mach-kirkwood/common.h2
-rw-r--r--arch/arm/mach-kirkwood/include/mach/kirkwood.h1
-rw-r--r--arch/arm/mach-kirkwood/mpp.h4
-rw-r--r--arch/arm/mach-kirkwood/ts219-setup.c220
-rw-r--r--arch/arm/mach-orion5x/ts78xx-fpga.h10
-rw-r--r--arch/arm/mach-orion5x/ts78xx-setup.c7
-rw-r--r--arch/arm/tools/mach-types10
-rw-r--r--drivers/rtc/rtc-mv.c11
12 files changed, 321 insertions, 11 deletions
diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
index 9ed4e1b8667..c367ae44012 100644
--- a/arch/arm/configs/kirkwood_defconfig
+++ b/arch/arm/configs/kirkwood_defconfig
@@ -180,6 +180,7 @@ CONFIG_MACH_DB88F6281_BP=y
CONFIG_MACH_RD88F6192_NAS=y
CONFIG_MACH_RD88F6281=y
CONFIG_MACH_SHEEVAPLUG=y
+CONFIG_MACH_TS219=y
CONFIG_PLAT_ORION=y
#
@@ -852,13 +853,20 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
+CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
-# CONFIG_INPUT_KEYBOARD is not set
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_KEYBOARD_GPIO=y
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
@@ -868,7 +876,11 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
#
# Hardware I/O ports
#
-# CONFIG_SERIO is not set
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SERIO_PCIPS2 is not set
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
@@ -1271,7 +1283,7 @@ CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
-# CONFIG_RTC_DRV_S35390A is not set
+CONFIG_RTC_DRV_S35390A=y
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 532443622a1..b5421cccd7e 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -26,6 +26,12 @@ config MACH_SHEEVAPLUG
Say 'Y' here if you want your kernel to support the
Marvell SheevaPlug Reference Board.
+config MACH_TS219
+ bool "QNAP TS-119 and TS-219 Turbo NAS"
+ help
+ Say 'Y' here if you want your kernel to support the
+ QNAP TS-119 and TS-219 Turbo NAS devices.
+
endmenu
endif
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index de81b4b5bd3..8f03c9b9bdd 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_MACH_DB88F6281_BP) += db88f6281-bp-setup.o
obj-$(CONFIG_MACH_RD88F6192_NAS) += rd88f6192-nas-setup.o
obj-$(CONFIG_MACH_RD88F6281) += rd88f6281-setup.o
obj-$(CONFIG_MACH_SHEEVAPLUG) += sheevaplug-setup.o
+obj-$(CONFIG_MACH_TS219) += ts219-setup.o
diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c
index 9f012551794..19b03f62c3f 100644
--- a/arch/arm/mach-kirkwood/common.c
+++ b/arch/arm/mach-kirkwood/common.c
@@ -14,6 +14,7 @@
#include <linux/serial_8250.h>
#include <linux/mbus.h>
#include <linux/mv643xx_eth.h>
+#include <linux/mv643xx_i2c.h>
#include <linux/ata_platform.h>
#include <linux/spi/orion_spi.h>
#include <net/dsa.h>
@@ -371,6 +372,45 @@ void __init kirkwood_spi_init()
/*****************************************************************************
+ * I2C
+ ****************************************************************************/
+static struct mv64xxx_i2c_pdata kirkwood_i2c_pdata = {
+ .freq_m = 8, /* assumes 166 MHz TCLK */
+ .freq_n = 3,
+ .timeout = 1000, /* Default timeout of 1 second */
+};
+
+static struct resource kirkwood_i2c_resources[] = {
+ {
+ .name = "i2c",
+ .start = I2C_PHYS_BASE,
+ .end = I2C_PHYS_BASE + 0x1f,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .name = "i2c",
+ .start = IRQ_KIRKWOOD_TWSI,
+ .end = IRQ_KIRKWOOD_TWSI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device kirkwood_i2c = {
+ .name = MV64XXX_I2C_CTLR_NAME,
+ .id = 0,
+ .num_resources = ARRAY_SIZE(kirkwood_i2c_resources),
+ .resource = kirkwood_i2c_resources,
+ .dev = {
+ .platform_data = &kirkwood_i2c_pdata,
+ },
+};
+
+void __init kirkwood_i2c_init(void)
+{
+ platform_device_register(&kirkwood_i2c);
+}
+
+
+/*****************************************************************************
* UART0
****************************************************************************/
static struct plat_serial8250_port kirkwood_uart0_data[] = {
diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
index 9e5282684d5..6ee88406f38 100644
--- a/arch/arm/mach-kirkwood/common.h
+++ b/arch/arm/mach-kirkwood/common.h
@@ -37,9 +37,11 @@ void kirkwood_pcie_init(void);
void kirkwood_sata_init(struct mv_sata_platform_data *sata_data);
void kirkwood_sdio_init(struct mvsdio_platform_data *mvsdio_data);
void kirkwood_spi_init(void);
+void kirkwood_i2c_init(void);
void kirkwood_uart0_init(void);
void kirkwood_uart1_init(void);
+extern int kirkwood_tclk;
extern struct sys_timer kirkwood_timer;
diff --git a/arch/arm/mach-kirkwood/include/mach/kirkwood.h b/arch/arm/mach-kirkwood/include/mach/kirkwood.h
index d3db30fe763..38c98685359 100644
--- a/arch/arm/mach-kirkwood/include/mach/kirkwood.h
+++ b/arch/arm/mach-kirkwood/include/mach/kirkwood.h
@@ -93,6 +93,7 @@
#define DEVICE_ID (DEV_BUS_VIRT_BASE | 0x0034)
#define RTC_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x0300)
#define SPI_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x0600)
+#define I2C_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x1000)
#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000)
#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000)
#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100)
diff --git a/arch/arm/mach-kirkwood/mpp.h b/arch/arm/mach-kirkwood/mpp.h
index 45cccb74310..e021a80c2ca 100644
--- a/arch/arm/mach-kirkwood/mpp.h
+++ b/arch/arm/mach-kirkwood/mpp.h
@@ -90,13 +90,13 @@
#define MPP10_GPO MPP( 10, 0x0, 0, 1, 1, 1, 1, 1 )
#define MPP10_SPI_SCK MPP( 10, 0x2, 0, 1, 1, 1, 1, 1 )
-#define MPP10_UArt0_TXD MPP( 10, 0X3, 0, 1, 1, 1, 1, 1 )
+#define MPP10_UART0_TXD MPP( 10, 0X3, 0, 1, 1, 1, 1, 1 )
#define MPP10_SATA1_ACTn MPP( 10, 0x5, 0, 1, 0, 0, 1, 1 )
#define MPP10_PTP_TRIG_GEN MPP( 10, 0xc, 0, 1, 1, 1, 1, 1 )
#define MPP11_GPIO MPP( 11, 0x0, 1, 1, 1, 1, 1, 1 )
#define MPP11_SPI_MISO MPP( 11, 0x2, 1, 0, 1, 1, 1, 1 )
-#define MPP11_UArt0_RXD MPP( 11, 0x3, 1, 0, 1, 1, 1, 1 )
+#define MPP11_UART0_RXD MPP( 11, 0x3, 1, 0, 1, 1, 1, 1 )
#define MPP11_PTP_EVENT_REQ MPP( 11, 0x4, 1, 0, 1, 1, 1, 1 )
#define MPP11_PTP_TRIG_GEN MPP( 11, 0xc, 0, 1, 1, 1, 1, 1 )
#define MPP11_PTP_CLK MPP( 11, 0xd, 1, 0, 1, 1, 1, 1 )
diff --git a/arch/arm/mach-kirkwood/ts219-setup.c b/arch/arm/mach-kirkwood/ts219-setup.c
new file mode 100644
index 00000000000..dda5743cf3e
--- /dev/null
+++ b/arch/arm/mach-kirkwood/ts219-setup.c
@@ -0,0 +1,220 @@
+/*
+ *
+ * QNAP TS-119/TS-219 Turbo NAS Board Setup
+ *
+ * Copyright (C) 2009 Martin Michlmayr <tbm@cyrius.com>
+ * Copyright (C) 2008 Byron Bradley <byron.bbradley@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/orion_spi.h>
+#include <linux/i2c.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/ata_platform.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/timex.h>
+#include <linux/serial_reg.h>
+#include <linux/pci.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+#include "mpp.h"
+
+/****************************************************************************
+ * 16 MiB NOR flash. The struct mtd_partition is not in the same order as the
+ * partitions on the device because we want to keep compatability with
+ * the QNAP firmware.
+ * Layout as used by QNAP:
+ * 0x00000000-0x00080000 : "U-Boot"
+ * 0x00200000-0x00400000 : "Kernel"
+ * 0x00400000-0x00d00000 : "RootFS"
+ * 0x00d00000-0x01000000 : "RootFS2"
+ * 0x00080000-0x000c0000 : "U-Boot Config"
+ * 0x000c0000-0x00200000 : "NAS Config"
+ *
+ * We'll use "RootFS1" instead of "RootFS" to stay compatible with the layout
+ * used by the QNAP TS-109/TS-209.
+ *
+ ***************************************************************************/
+
+static struct mtd_partition qnap_ts219_partitions[] = {
+ {
+ .name = "U-Boot",
+ .size = 0x00080000,
+ .offset = 0,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "Kernel",
+ .size = 0x00200000,
+ .offset = 0x00200000,
+ }, {
+ .name = "RootFS1",
+ .size = 0x00900000,
+ .offset = 0x00400000,
+ }, {
+ .name = "RootFS2",
+ .size = 0x00300000,
+ .offset = 0x00d00000,
+ }, {
+ .name = "U-Boot Config",
+ .size = 0x00040000,
+ .offset = 0x00080000,
+ }, {
+ .name = "NAS Config",
+ .size = 0x00140000,
+ .offset = 0x000c0000,
+ },
+};
+
+static const struct flash_platform_data qnap_ts219_flash = {
+ .type = "m25p128",
+ .name = "spi_flash",
+ .parts = qnap_ts219_partitions,
+ .nr_parts = ARRAY_SIZE(qnap_ts219_partitions),
+};
+
+static struct spi_board_info __initdata qnap_ts219_spi_slave_info[] = {
+ {
+ .modalias = "m25p80",
+ .platform_data = &qnap_ts219_flash,
+ .irq = -1,
+ .max_speed_hz = 20000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ },
+};
+
+static struct i2c_board_info __initdata qnap_ts219_i2c_rtc = {
+ I2C_BOARD_INFO("s35390a", 0x30),
+};
+
+static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(8),
+};
+
+static struct mv_sata_platform_data qnap_ts219_sata_data = {
+ .n_ports = 2,
+};
+
+static struct gpio_keys_button qnap_ts219_buttons[] = {
+ {
+ .code = KEY_COPY,
+ .gpio = 15,
+ .desc = "USB Copy",
+ .active_low = 1,
+ },
+ {
+ .code = KEY_RESTART,
+ .gpio = 16,
+ .desc = "Reset",
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_platform_data qnap_ts219_button_data = {
+ .buttons = qnap_ts219_buttons,
+ .nbuttons = ARRAY_SIZE(qnap_ts219_buttons),
+};
+
+static struct platform_device qnap_ts219_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &qnap_ts219_button_data,
+ }
+};
+
+static unsigned int qnap_ts219_mpp_config[] __initdata = {
+ MPP0_SPI_SCn,
+ MPP1_SPI_MOSI,
+ MPP2_SPI_SCK,
+ MPP3_SPI_MISO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP13_UART1_TXD, /* PIC controller */
+ MPP14_UART1_RXD, /* PIC controller */
+ MPP15_GPIO, /* USB Copy button */
+ MPP16_GPIO, /* Reset button */
+ MPP20_SATA1_ACTn,
+ MPP21_SATA0_ACTn,
+ MPP22_SATA1_PRESENTn,
+ MPP23_SATA0_PRESENTn,
+ 0
+};
+
+
+/*****************************************************************************
+ * QNAP TS-x19 specific power off method via UART1-attached PIC
+ ****************************************************************************/
+
+#define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2))
+
+void qnap_ts219_power_off(void)
+{
+ /* 19200 baud divisor */
+ const unsigned divisor = ((kirkwood_tclk + (8 * 19200)) / (16 * 19200));
+
+ pr_info("%s: triggering power-off...\n", __func__);
+
+ /* hijack UART1 and reset into sane state (19200,8n1) */
+ writel(0x83, UART1_REG(LCR));
+ writel(divisor & 0xff, UART1_REG(DLL));
+ writel((divisor >> 8) & 0xff, UART1_REG(DLM));
+ writel(0x03, UART1_REG(LCR));
+ writel(0x00, UART1_REG(IER));
+ writel(0x00, UART1_REG(FCR));
+ writel(0x00, UART1_REG(MCR));
+
+ /* send the power-off command 'A' to PIC */
+ writel('A', UART1_REG(TX));
+}
+
+static void __init qnap_ts219_init(void)
+{
+ /*
+ * Basic setup. Needs to be called early.
+ */
+ kirkwood_init();
+ kirkwood_mpp_conf(qnap_ts219_mpp_config);
+
+ kirkwood_uart0_init();
+ kirkwood_uart1_init(); /* A PIC controller is connected here. */
+ spi_register_board_info(qnap_ts219_spi_slave_info,
+ ARRAY_SIZE(qnap_ts219_spi_slave_info));
+ kirkwood_spi_init();
+ kirkwood_i2c_init();
+ i2c_register_board_info(0, &qnap_ts219_i2c_rtc, 1);
+ kirkwood_ge00_init(&qnap_ts219_ge00_data);
+ kirkwood_sata_init(&qnap_ts219_sata_data);
+ kirkwood_ehci_init();
+ platform_device_register(&qnap_ts219_button_device);
+
+ pm_power_off = qnap_ts219_power_off;
+
+}
+
+MACHINE_START(TS219, "QNAP TS-119/TS-219")
+ /* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
+ .phys_io = KIRKWOOD_REGS_PHYS_BASE,
+ .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+ .boot_params = 0x00000100,
+ .init_machine = qnap_ts219_init,
+ .map_io = kirkwood_map_io,
+ .init_irq = kirkwood_init_irq,
+ .timer = &kirkwood_timer,
+MACHINE_END
diff --git a/arch/arm/mach-orion5x/ts78xx-fpga.h b/arch/arm/mach-orion5x/ts78xx-fpga.h
index 0a314ddef65..0f9cdf45895 100644
--- a/arch/arm/mach-orion5x/ts78xx-fpga.h
+++ b/arch/arm/mach-orion5x/ts78xx-fpga.h
@@ -6,8 +6,14 @@
*/
enum fpga_ids {
/* Technologic Systems */
- TS7800_REV_B2 = FPGAID(0x00b480, 0x02),
- TS7800_REV_B3 = FPGAID(0x00b480, 0x03),
+ TS7800_REV_1 = FPGAID(0x00b480, 0x01),
+ TS7800_REV_2 = FPGAID(0x00b480, 0x02),
+ TS7800_REV_3 = FPGAID(0x00b480, 0x03),
+ TS7800_REV_4 = FPGAID(0x00b480, 0x04),
+ TS7800_REV_5 = FPGAID(0x00b480, 0x05),
+
+ /* Unaffordable & Expensive */
+ UAE_DUMMY = FPGAID(0xffffff, 0x01),
};
struct fpga_device {
diff --git a/arch/arm/mach-orion5x/ts78xx-setup.c b/arch/arm/mach-orion5x/ts78xx-setup.c
index f5191ddea08..9a6b397f972 100644
--- a/arch/arm/mach-orion5x/ts78xx-setup.c
+++ b/arch/arm/mach-orion5x/ts78xx-setup.c
@@ -282,8 +282,11 @@ static void ts78xx_fpga_supports(void)
{
/* TODO: put this 'table' into ts78xx-fpga.h */
switch (ts78xx_fpga.id) {
- case TS7800_REV_B2:
- case TS7800_REV_B3:
+ case TS7800_REV_1:
+ case TS7800_REV_2:
+ case TS7800_REV_3:
+ case TS7800_REV_4:
+ case TS7800_REV_5:
ts78xx_fpga.supports.ts_rtc.present = 1;
ts78xx_fpga.supports.ts_nand.present = 1;
break;
diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types
index b4211d8b2ac..945e0d237a1 100644
--- a/arch/arm/tools/mach-types
+++ b/arch/arm/tools/mach-types
@@ -12,7 +12,7 @@
#
# http://www.arm.linux.org.uk/developer/machines/?action=new
#
-# Last update: Thu Mar 12 18:01:45 2009
+# Last update: Mon Mar 23 20:09:01 2009
#
# machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number
#
@@ -2124,3 +2124,11 @@ mx27wallace MACH_MX27WALLACE MX27WALLACE 2133
fmzwebmodul MACH_FMZWEBMODUL FMZWEBMODUL 2134
rd78x00_masa MACH_RD78X00_MASA RD78X00_MASA 2135
smallogger MACH_SMALLOGGER SMALLOGGER 2136
+ccw9p9215 MACH_CCW9P9215 CCW9P9215 2137
+dm355_leopard MACH_DM355_LEOPARD DM355_LEOPARD 2138
+ts219 MACH_TS219 TS219 2139
+tny_a9263 MACH_TNY_A9263 TNY_A9263 2140
+apollo MACH_APOLLO APOLLO 2141
+at91cap9stk MACH_AT91CAP9STK AT91CAP9STK 2142
+spc300 MACH_SPC300 SPC300 2143
+eko MACH_EKO EKO 2144
diff --git a/drivers/rtc/rtc-mv.c b/drivers/rtc/rtc-mv.c
index 45f12dcd371..e0263d2005e 100644
--- a/drivers/rtc/rtc-mv.c
+++ b/drivers/rtc/rtc-mv.c
@@ -12,6 +12,7 @@
#include <linux/bcd.h>
#include <linux/io.h>
#include <linux/platform_device.h>
+#include <linux/delay.h>
#define RTC_TIME_REG_OFFS 0
@@ -119,6 +120,16 @@ static int __init mv_rtc_probe(struct platform_device *pdev)
return -EINVAL;
}
+ /* make sure it is actually functional */
+ if (rtc_time == 0x01000000) {
+ ssleep(1);
+ rtc_time = readl(pdata->ioaddr + RTC_TIME_REG_OFFS);
+ if (rtc_time == 0x01000000) {
+ dev_err(&pdev->dev, "internal RTC not ticking\n");
+ return -ENODEV;
+ }
+ }
+
platform_set_drvdata(pdev, pdata);
pdata->rtc = rtc_device_register(pdev->name, &pdev->dev,
&mv_rtc_ops, THIS_MODULE);