aboutsummaryrefslogtreecommitdiff
path: root/drivers/tty/serial/m32r_sio_reg.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/m32r_sio_reg.h')
-rw-r--r--drivers/tty/serial/m32r_sio_reg.h152
1 files changed, 152 insertions, 0 deletions
diff --git a/drivers/tty/serial/m32r_sio_reg.h b/drivers/tty/serial/m32r_sio_reg.h
new file mode 100644
index 00000000000..4671473793e
--- /dev/null
+++ b/drivers/tty/serial/m32r_sio_reg.h
@@ -0,0 +1,152 @@
+/*
+ * m32r_sio_reg.h
+ *
+ * Copyright (C) 1992, 1994 by Theodore Ts'o.
+ * Copyright (C) 2004 Hirokazu Takata <takata at linux-m32r.org>
+ *
+ * Redistribution of this file is permitted under the terms of the GNU
+ * Public License (GPL)
+ *
+ * These are the UART port assignments, expressed as offsets from the base
+ * register. These assignments should hold for any serial port based on
+ * a 8250, 16450, or 16550(A).
+ */
+
+#ifndef _M32R_SIO_REG_H
+#define _M32R_SIO_REG_H
+
+
+#ifdef CONFIG_SERIAL_M32R_PLDSIO
+
+#define SIOCR 0x000
+#define SIOMOD0 0x002
+#define SIOMOD1 0x004
+#define SIOSTS 0x006
+#define SIOTRCR 0x008
+#define SIOBAUR 0x00a
+// #define SIORBAUR 0x018
+#define SIOTXB 0x00c
+#define SIORXB 0x00e
+
+#define UART_RX ((unsigned long) PLD_ESIO0RXB)
+ /* In: Receive buffer (DLAB=0) */
+#define UART_TX ((unsigned long) PLD_ESIO0TXB)
+ /* Out: Transmit buffer (DLAB=0) */
+#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
+#define UART_TRG 0 /* (LCR=BF) FCTR bit 7 selects Rx or Tx
+ * In: Fifo count
+ * Out: Fifo custom trigger levels
+ * XR16C85x only */
+
+#define UART_DLM 0 /* Out: Divisor Latch High (DLAB=1) */
+#define UART_IER ((unsigned long) PLD_ESIO0INTCR)
+ /* Out: Interrupt Enable Register */
+#define UART_FCTR 0 /* (LCR=BF) Feature Control Register
+ * XR16C85x only */
+
+#define UART_IIR 0 /* In: Interrupt ID Register */
+#define UART_FCR 0 /* Out: FIFO Control Register */
+#define UART_EFR 0 /* I/O: Extended Features Register */
+ /* (DLAB=1, 16C660 only) */
+
+#define UART_LCR 0 /* Out: Line Control Register */
+#define UART_MCR 0 /* Out: Modem Control Register */
+#define UART_LSR ((unsigned long) PLD_ESIO0STS)
+ /* In: Line Status Register */
+#define UART_MSR 0 /* In: Modem Status Register */
+#define UART_SCR 0 /* I/O: Scratch Register */
+#define UART_EMSR 0 /* (LCR=BF) Extended Mode Select Register
+ * FCTR bit 6 selects SCR or EMSR
+ * XR16c85x only */
+
+#else /* not CONFIG_SERIAL_M32R_PLDSIO */
+
+#define SIOCR 0x000
+#define SIOMOD0 0x004
+#define SIOMOD1 0x008
+#define SIOSTS 0x00c
+#define SIOTRCR 0x010
+#define SIOBAUR 0x014
+#define SIORBAUR 0x018
+#define SIOTXB 0x01c
+#define SIORXB 0x020
+
+#define UART_RX M32R_SIO0_RXB_PORTL /* In: Receive buffer (DLAB=0) */
+#define UART_TX M32R_SIO0_TXB_PORTL /* Out: Transmit buffer (DLAB=0) */
+#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
+#define UART_TRG 0 /* (LCR=BF) FCTR bit 7 selects Rx or Tx
+ * In: Fifo count
+ * Out: Fifo custom trigger levels
+ * XR16C85x only */
+
+#define UART_DLM 0 /* Out: Divisor Latch High (DLAB=1) */
+#define UART_IER M32R_SIO0_TRCR_PORTL /* Out: Interrupt Enable Register */
+#define UART_FCTR 0 /* (LCR=BF) Feature Control Register
+ * XR16C85x only */
+
+#define UART_IIR 0 /* In: Interrupt ID Register */
+#define UART_FCR 0 /* Out: FIFO Control Register */
+#define UART_EFR 0 /* I/O: Extended Features Register */
+ /* (DLAB=1, 16C660 only) */
+
+#define UART_LCR 0 /* Out: Line Control Register */
+#define UART_MCR 0 /* Out: Modem Control Register */
+#define UART_LSR M32R_SIO0_STS_PORTL /* In: Line Status Register */
+#define UART_MSR 0 /* In: Modem Status Register */
+#define UART_SCR 0 /* I/O: Scratch Register */
+#define UART_EMSR 0 /* (LCR=BF) Extended Mode Select Register
+ * FCTR bit 6 selects SCR or EMSR
+ * XR16c85x only */
+
+#endif /* CONFIG_SERIAL_M32R_PLDSIO */
+
+#define UART_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
+
+/*
+ * These are the definitions for the Line Control Register
+ *
+ * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
+ * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
+ */
+#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
+#define UART_LCR_SBC 0x40 /* Set break control */
+#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
+#define UART_LCR_EPAR 0x10 /* Even parity select */
+#define UART_LCR_PARITY 0x08 /* Parity Enable */
+#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
+#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
+#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
+#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
+#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
+
+/*
+ * These are the definitions for the Line Status Register
+ */
+#define UART_LSR_TEMT 0x02 /* Transmitter empty */
+#define UART_LSR_THRE 0x01 /* Transmit-hold-register empty */
+#define UART_LSR_BI 0x00 /* Break interrupt indicator */
+#define UART_LSR_FE 0x80 /* Frame error indicator */
+#define UART_LSR_PE 0x40 /* Parity error indicator */
+#define UART_LSR_OE 0x20 /* Overrun error indicator */
+#define UART_LSR_DR 0x04 /* Receiver data ready */
+
+/*
+ * These are the definitions for the Interrupt Identification Register
+ */
+#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
+#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
+
+#define UART_IIR_MSI 0x00 /* Modem status interrupt */
+#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
+#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
+#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
+
+/*
+ * These are the definitions for the Interrupt Enable Register
+ */
+#define UART_IER_MSI 0x00 /* Enable Modem status interrupt */
+#define UART_IER_RLSI 0x08 /* Enable receiver line status interrupt */
+#define UART_IER_THRI 0x03 /* Enable Transmitter holding register int. */
+#define UART_IER_RDI 0x04 /* Enable receiver data interrupt */
+
+#endif /* _M32R_SIO_REG_H */