Patch by Robert Schwebel, 13 May 2004:

Add 'imgextract' command: extract one part of a multi file image.

1 files changed, 15 insertions, 8 deletions

diff --git a/doc/README.mpc85xxads b/doc/README.mpc85xxads
index 4c1686faa..c49b2a896 100644
--- a/doc/README.mpc85xxads
+++ b/doc/README.mpc85xxads
@@ -5,10 +5,12 @@ Created 10/15/03
 -----------------------------------------
 
 0. Toolchain
-The Binutils in current ELDK toolchain will not support MPC85xx chip. You need
-use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
+The Binutils in ELDK toolchain 3.0 or earlier does not support the
+MPC85xx chip. You need use the newest binutils-2.14.tar.bz2 from
+http://ftp.gnu.org/gnu/binutils.
 
 1. SWITCH SETTINGS & JUMPERS
+
 1.1 First, make sure the board default setting is consistent with the document
     shipped with your board. Then apply the following changes:
     SW3[1-6]="all OFF"  (boot from 32bit flash, no boot sequence is used)
@@ -19,11 +21,13 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
     SW22[1-4]="OFF OFF ON OFF"
     SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
     J1 = "Enable Prog" (Make sure your flash is programmable for development)
+
 1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will
     have to change the system clock from the default 66Mhz to 33Mhz by
     setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
     double your platform clock(SW6) because the system clock is now only
-    half of its original value. 
+    half of its original value.
+
 1.3 SW6 is a very important switch, it decides your platform clock and CPU
     clock based on the on-board system clock(default 66MHz). Check the
     document along with your board for details.
@@ -35,7 +39,7 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
      between u-boot and linux kernel, you can customize it based on your
      system requirements:
 
-     0x0000_0000     0x7fff_ffff     DDR                     2G 
+     0x0000_0000     0x7fff_ffff     DDR                     2G
      0x8000_0000     0x9fff_ffff     PCI MEM                 512M
      0xc000_0000     0xdfff_ffff     Rapid IO                512M
      0xe000_0000     0xe000_ffff     CCSR                    1M
@@ -52,7 +56,9 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
 	arch/ppc/configs/mpc8540_ads_defconfig
 	arch/ppc/configs/mpc8560_ads_defconfig
 
+
 3. DEFINITIONS AND COMPILATION
+
 3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/
     configs/MPC8560ADS.h
     CONFIG_BOOKE            BOOKE(e.g. Motorola MPC85xx, IBM 440, etc)
@@ -74,7 +80,6 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
 			    if you can program the flash directly, undef this.
     Other than the above definitions, the rest in the config files are straightforward.
 
-
 3.2 Compilation
    export CROSS_COMPILE=your-cross-compile-prefix(assuming you're using BASH shell)
    cd u-boot
@@ -82,7 +87,9 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
    make MPC8560ADS_config (or make MPC8540ADS_config)
    make
 
+
 4.  Notes:
+
 4.1 When connecting with kermit, the following commands must be present.in
    your .kermrc file. These are especially important when booting as
    MPC8560, as the serial console will not work without them:
@@ -93,7 +100,6 @@ set handshake none
 set flow-control none
 robust
 
-   
 4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that
    happens, you can try the following steps to make network work:
    MPC8560ADS>tftp 1000000 pImage
@@ -103,9 +109,9 @@ robust
    >1
    >. (to quit this memory operation)
    MPC8560ADS>tftp 1000000 pImage
-4.3 If you're one of the early developers using the Rev1 8540/8560 chips, please use U-Boot 
-   1.0.0, as the newer silicon will only support Rev2 and future revisions of 8540/8560.
 
+4.3 If you're one of the early developers using the Rev1 8540/8560 chips, please use U-Boot
+   1.0.0, as the newer silicon will only support Rev2 and future revisions of 8540/8560.
 
 4.4 Reflash U-boot Image using U-boot
 
@@ -116,6 +122,7 @@ robust
 
 
 5. Screen dump:
+
 5.1 MPC8540ADS board
 U-Boot 1.0.0-pre (Oct 15 2003 - 13:40:33)