diff --git a/drivers/tty/rocket.c b/drivers/tty/rocket.c
index 82d35c5..354564e 100644
--- a/drivers/tty/rocket.c
+++ b/drivers/tty/rocket.c
@@ -150,12 +150,14 @@
 	AIOP_INTR_BIT_3
 };
 
+#ifdef CONFIG_PCI
 static Word_t upci_aiop_intr_bits[AIOP_CTL_SIZE] = {
 	UPCI_AIOP_INTR_BIT_0,
 	UPCI_AIOP_INTR_BIT_1,
 	UPCI_AIOP_INTR_BIT_2,
 	UPCI_AIOP_INTR_BIT_3
 };
+#endif
 
 static Byte_t RData[RDATASIZE] = {
 	0x00, 0x09, 0xf6, 0x82,
@@ -227,7 +229,6 @@
 static int __init init_ISA(int i);
 static void rp_wait_until_sent(struct tty_struct *tty, int timeout);
 static void rp_flush_buffer(struct tty_struct *tty);
-static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model);
 static unsigned char GetLineNumber(int ctrl, int aiop, int ch);
 static unsigned char SetLineNumber(int ctrl, int aiop, int ch);
 static void rp_start(struct tty_struct *tty);
@@ -241,11 +242,6 @@
 static void sModemReset(CONTROLLER_T * CtlP, int chan, int on);
 static void sPCIModemReset(CONTROLLER_T * CtlP, int chan, int on);
 static int sWriteTxPrioByte(CHANNEL_T * ChP, Byte_t Data);
-static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
-			      ByteIO_t * AiopIOList, int AiopIOListSize,
-			      WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
-			      int PeriodicOnly, int altChanRingIndicator,
-			      int UPCIRingInd);
 static int sInitController(CONTROLLER_T * CtlP, int CtlNum, ByteIO_t MudbacIO,
 			   ByteIO_t * AiopIOList, int AiopIOListSize,
 			   int IRQNum, Byte_t Frequency, int PeriodicOnly);
@@ -1775,6 +1771,145 @@
 };
 MODULE_DEVICE_TABLE(pci, rocket_pci_ids);
 
+/*  Resets the speaker controller on RocketModem II and III devices */
+static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model)
+{
+	ByteIO_t addr;
+
+	/* RocketModem II speaker control is at the 8th port location of offset 0x40 */
+	if ((model == MODEL_RP4M) || (model == MODEL_RP6M)) {
+		addr = CtlP->AiopIO[0] + 0x4F;
+		sOutB(addr, 0);
+	}
+
+	/* RocketModem III speaker control is at the 1st port location of offset 0x80 */
+	if ((model == MODEL_UPCI_RM3_8PORT)
+	    || (model == MODEL_UPCI_RM3_4PORT)) {
+		addr = CtlP->AiopIO[0] + 0x88;
+		sOutB(addr, 0);
+	}
+}
+
+/***************************************************************************
+Function: sPCIInitController
+Purpose:  Initialization of controller global registers and controller
+          structure.
+Call:     sPCIInitController(CtlP,CtlNum,AiopIOList,AiopIOListSize,
+                          IRQNum,Frequency,PeriodicOnly)
+          CONTROLLER_T *CtlP; Ptr to controller structure
+          int CtlNum; Controller number
+          ByteIO_t *AiopIOList; List of I/O addresses for each AIOP.
+             This list must be in the order the AIOPs will be found on the
+             controller.  Once an AIOP in the list is not found, it is
+             assumed that there are no more AIOPs on the controller.
+          int AiopIOListSize; Number of addresses in AiopIOList
+          int IRQNum; Interrupt Request number.  Can be any of the following:
+                         0: Disable global interrupts
+                         3: IRQ 3
+                         4: IRQ 4
+                         5: IRQ 5
+                         9: IRQ 9
+                         10: IRQ 10
+                         11: IRQ 11
+                         12: IRQ 12
+                         15: IRQ 15
+          Byte_t Frequency: A flag identifying the frequency
+                   of the periodic interrupt, can be any one of the following:
+                      FREQ_DIS - periodic interrupt disabled
+                      FREQ_137HZ - 137 Hertz
+                      FREQ_69HZ - 69 Hertz
+                      FREQ_34HZ - 34 Hertz
+                      FREQ_17HZ - 17 Hertz
+                      FREQ_9HZ - 9 Hertz
+                      FREQ_4HZ - 4 Hertz
+                   If IRQNum is set to 0 the Frequency parameter is
+                   overidden, it is forced to a value of FREQ_DIS.
+          int PeriodicOnly: 1 if all interrupts except the periodic
+                               interrupt are to be blocked.
+                            0 is both the periodic interrupt and
+                               other channel interrupts are allowed.
+                            If IRQNum is set to 0 the PeriodicOnly parameter is
+                               overidden, it is forced to a value of 0.
+Return:   int: Number of AIOPs on the controller, or CTLID_NULL if controller
+               initialization failed.
+
+Comments:
+          If periodic interrupts are to be disabled but AIOP interrupts
+          are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
+
+          If interrupts are to be completely disabled set IRQNum to 0.
+
+          Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
+          invalid combination.
+
+          This function performs initialization of global interrupt modes,
+          but it does not actually enable global interrupts.  To enable
+          and disable global interrupts use functions sEnGlobalInt() and
+          sDisGlobalInt().  Enabling of global interrupts is normally not
+          done until all other initializations are complete.
+
+          Even if interrupts are globally enabled, they must also be
+          individually enabled for each channel that is to generate
+          interrupts.
+
+Warnings: No range checking on any of the parameters is done.
+
+          No context switches are allowed while executing this function.
+
+          After this function all AIOPs on the controller are disabled,
+          they can be enabled with sEnAiop().
+*/
+static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
+			      ByteIO_t * AiopIOList, int AiopIOListSize,
+			      WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
+			      int PeriodicOnly, int altChanRingIndicator,
+			      int UPCIRingInd)
+{
+	int i;
+	ByteIO_t io;
+
+	CtlP->AltChanRingIndicator = altChanRingIndicator;
+	CtlP->UPCIRingInd = UPCIRingInd;
+	CtlP->CtlNum = CtlNum;
+	CtlP->CtlID = CTLID_0001;	/* controller release 1 */
+	CtlP->BusType = isPCI;	/* controller release 1 */
+
+	if (ConfigIO) {
+		CtlP->isUPCI = 1;
+		CtlP->PCIIO = ConfigIO + _PCI_9030_INT_CTRL;
+		CtlP->PCIIO2 = ConfigIO + _PCI_9030_GPIO_CTRL;
+		CtlP->AiopIntrBits = upci_aiop_intr_bits;
+	} else {
+		CtlP->isUPCI = 0;
+		CtlP->PCIIO =
+		    (WordIO_t) ((ByteIO_t) AiopIOList[0] + _PCI_INT_FUNC);
+		CtlP->AiopIntrBits = aiop_intr_bits;
+	}
+
+	sPCIControllerEOI(CtlP);	/* clear EOI if warm init */
+	/* Init AIOPs */
+	CtlP->NumAiop = 0;
+	for (i = 0; i < AiopIOListSize; i++) {
+		io = AiopIOList[i];
+		CtlP->AiopIO[i] = (WordIO_t) io;
+		CtlP->AiopIntChanIO[i] = io + _INT_CHAN;
+
+		CtlP->AiopID[i] = sReadAiopID(io);	/* read AIOP ID */
+		if (CtlP->AiopID[i] == AIOPID_NULL)	/* if AIOP does not exist */
+			break;	/* done looking for AIOPs */
+
+		CtlP->AiopNumChan[i] = sReadAiopNumChan((WordIO_t) io);	/* num channels in AIOP */
+		sOutW((WordIO_t) io + _INDX_ADDR, _CLK_PRE);	/* clock prescaler */
+		sOutB(io + _INDX_DATA, sClockPrescale);
+		CtlP->NumAiop++;	/* bump count of AIOPs */
+	}
+
+	if (CtlP->NumAiop == 0)
+		return (-1);
+	else
+		return (CtlP->NumAiop);
+}
+
 /*
  *  Called when a PCI card is found.  Retrieves and stores model information,
  *  init's aiopic and serial port hardware.
@@ -2519,147 +2654,6 @@
 		return (CtlP->NumAiop);
 }
 
-#ifdef CONFIG_PCI
-/***************************************************************************
-Function: sPCIInitController
-Purpose:  Initialization of controller global registers and controller
-          structure.
-Call:     sPCIInitController(CtlP,CtlNum,AiopIOList,AiopIOListSize,
-                          IRQNum,Frequency,PeriodicOnly)
-          CONTROLLER_T *CtlP; Ptr to controller structure
-          int CtlNum; Controller number
-          ByteIO_t *AiopIOList; List of I/O addresses for each AIOP.
-             This list must be in the order the AIOPs will be found on the
-             controller.  Once an AIOP in the list is not found, it is
-             assumed that there are no more AIOPs on the controller.
-          int AiopIOListSize; Number of addresses in AiopIOList
-          int IRQNum; Interrupt Request number.  Can be any of the following:
-                         0: Disable global interrupts
-                         3: IRQ 3
-                         4: IRQ 4
-                         5: IRQ 5
-                         9: IRQ 9
-                         10: IRQ 10
-                         11: IRQ 11
-                         12: IRQ 12
-                         15: IRQ 15
-          Byte_t Frequency: A flag identifying the frequency
-                   of the periodic interrupt, can be any one of the following:
-                      FREQ_DIS - periodic interrupt disabled
-                      FREQ_137HZ - 137 Hertz
-                      FREQ_69HZ - 69 Hertz
-                      FREQ_34HZ - 34 Hertz
-                      FREQ_17HZ - 17 Hertz
-                      FREQ_9HZ - 9 Hertz
-                      FREQ_4HZ - 4 Hertz
-                   If IRQNum is set to 0 the Frequency parameter is
-                   overidden, it is forced to a value of FREQ_DIS.
-          int PeriodicOnly: 1 if all interrupts except the periodic
-                               interrupt are to be blocked.
-                            0 is both the periodic interrupt and
-                               other channel interrupts are allowed.
-                            If IRQNum is set to 0 the PeriodicOnly parameter is
-                               overidden, it is forced to a value of 0.
-Return:   int: Number of AIOPs on the controller, or CTLID_NULL if controller
-               initialization failed.
-
-Comments:
-          If periodic interrupts are to be disabled but AIOP interrupts
-          are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
-
-          If interrupts are to be completely disabled set IRQNum to 0.
-
-          Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
-          invalid combination.
-
-          This function performs initialization of global interrupt modes,
-          but it does not actually enable global interrupts.  To enable
-          and disable global interrupts use functions sEnGlobalInt() and
-          sDisGlobalInt().  Enabling of global interrupts is normally not
-          done until all other initializations are complete.
-
-          Even if interrupts are globally enabled, they must also be
-          individually enabled for each channel that is to generate
-          interrupts.
-
-Warnings: No range checking on any of the parameters is done.
-
-          No context switches are allowed while executing this function.
-
-          After this function all AIOPs on the controller are disabled,
-          they can be enabled with sEnAiop().
-*/
-static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
-			      ByteIO_t * AiopIOList, int AiopIOListSize,
-			      WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
-			      int PeriodicOnly, int altChanRingIndicator,
-			      int UPCIRingInd)
-{
-	int i;
-	ByteIO_t io;
-
-	CtlP->AltChanRingIndicator = altChanRingIndicator;
-	CtlP->UPCIRingInd = UPCIRingInd;
-	CtlP->CtlNum = CtlNum;
-	CtlP->CtlID = CTLID_0001;	/* controller release 1 */
-	CtlP->BusType = isPCI;	/* controller release 1 */
-
-	if (ConfigIO) {
-		CtlP->isUPCI = 1;
-		CtlP->PCIIO = ConfigIO + _PCI_9030_INT_CTRL;
-		CtlP->PCIIO2 = ConfigIO + _PCI_9030_GPIO_CTRL;
-		CtlP->AiopIntrBits = upci_aiop_intr_bits;
-	} else {
-		CtlP->isUPCI = 0;
-		CtlP->PCIIO =
-		    (WordIO_t) ((ByteIO_t) AiopIOList[0] + _PCI_INT_FUNC);
-		CtlP->AiopIntrBits = aiop_intr_bits;
-	}
-
-	sPCIControllerEOI(CtlP);	/* clear EOI if warm init */
-	/* Init AIOPs */
-	CtlP->NumAiop = 0;
-	for (i = 0; i < AiopIOListSize; i++) {
-		io = AiopIOList[i];
-		CtlP->AiopIO[i] = (WordIO_t) io;
-		CtlP->AiopIntChanIO[i] = io + _INT_CHAN;
-
-		CtlP->AiopID[i] = sReadAiopID(io);	/* read AIOP ID */
-		if (CtlP->AiopID[i] == AIOPID_NULL)	/* if AIOP does not exist */
-			break;	/* done looking for AIOPs */
-
-		CtlP->AiopNumChan[i] = sReadAiopNumChan((WordIO_t) io);	/* num channels in AIOP */
-		sOutW((WordIO_t) io + _INDX_ADDR, _CLK_PRE);	/* clock prescaler */
-		sOutB(io + _INDX_DATA, sClockPrescale);
-		CtlP->NumAiop++;	/* bump count of AIOPs */
-	}
-
-	if (CtlP->NumAiop == 0)
-		return (-1);
-	else
-		return (CtlP->NumAiop);
-}
-
-/*  Resets the speaker controller on RocketModem II and III devices */
-static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model)
-{
-	ByteIO_t addr;
-
-	/* RocketModem II speaker control is at the 8th port location of offset 0x40 */
-	if ((model == MODEL_RP4M) || (model == MODEL_RP6M)) {
-		addr = CtlP->AiopIO[0] + 0x4F;
-		sOutB(addr, 0);
-	}
-
-	/* RocketModem III speaker control is at the 1st port location of offset 0x80 */
-	if ((model == MODEL_UPCI_RM3_8PORT)
-	    || (model == MODEL_UPCI_RM3_4PORT)) {
-		addr = CtlP->AiopIO[0] + 0x88;
-		sOutB(addr, 0);
-	}
-}
-#endif
-
 /***************************************************************************
 Function: sReadAiopID
 Purpose:  Read the AIOP idenfication number directly from an AIOP.