diff options
Diffstat (limited to 'Documentation/sound/alsa/ALSA-Configuration.txt')
| -rw-r--r-- | Documentation/sound/alsa/ALSA-Configuration.txt | 2322 |
1 files changed, 2322 insertions, 0 deletions
diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt new file mode 100644 index 00000000..ce6581c8 --- /dev/null +++ b/Documentation/sound/alsa/ALSA-Configuration.txt @@ -0,0 +1,2322 @@ + + Advanced Linux Sound Architecture - Driver + ========================================== + Configuration guide + + +Kernel Configuration +==================== + +To enable ALSA support you need at least to build the kernel with +primary sound card support (CONFIG_SOUND). Since ALSA can emulate OSS, +you don't have to choose any of the OSS modules. + +Enable "OSS API emulation" (CONFIG_SND_OSSEMUL) and both OSS mixer and +PCM supports if you want to run OSS applications with ALSA. + +If you want to support the WaveTable functionality on cards such as +SB Live! then you need to enable "Sequencer support" +(CONFIG_SND_SEQUENCER). + +To make ALSA debug messages more verbose, enable the "Verbose printk" +and "Debug" options. To check for memory leaks, turn on "Debug memory" +too. "Debug detection" will add checks for the detection of cards. + +Please note that all the ALSA ISA drivers support the Linux isapnp API +(if the card supports ISA PnP). You don't need to configure the cards +using isapnptools. + + +Creating ALSA devices +===================== + +This depends on your distribution, but normally you use the /dev/MAKEDEV +script to create the necessary device nodes. On some systems you use a +script named 'snddevices'. + + +Module parameters +================= + +The user can load modules with options. If the module supports more than +one card and you have more than one card of the same type then you can +specify multiple values for the option separated by commas. + +Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. + + Module snd + ---------- + + The core ALSA module. It is used by all ALSA card drivers. + It takes the following options which have global effects. + + major - major number for sound driver + - Default: 116 + cards_limit + - limiting card index for auto-loading (1-8) + - Default: 1 + - For auto-loading more than one card, specify this + option together with snd-card-X aliases. + slots - Reserve the slot index for the given driver. + This option takes multiple strings. + See "Module Autoloading Support" section for details. + debug - Specifies the debug message level + (0 = disable debug prints, 1 = normal debug messages, + 2 = verbose debug messages) + This option appears only when CONFIG_SND_DEBUG=y. + This option can be dynamically changed via sysfs + /sys/modules/snd/parameters/debug file. + + Module snd-pcm-oss + ------------------ + + The PCM OSS emulation module. + This module takes options which change the mapping of devices. + + dsp_map - PCM device number maps assigned to the 1st OSS device. + - Default: 0 + adsp_map - PCM device number maps assigned to the 2st OSS device. + - Default: 1 + nonblock_open + - Don't block opening busy PCM devices. Default: 1 + + For example, when dsp_map=2, /dev/dsp will be mapped to PCM #2 of + the card #0. Similarly, when adsp_map=0, /dev/adsp will be mapped + to PCM #0 of the card #0. + For changing the second or later card, specify the option with + commas, such like "dsp_map=0,1". + + nonblock_open option is used to change the behavior of the PCM + regarding opening the device. When this option is non-zero, + opening a busy OSS PCM device won't be blocked but return + immediately with EAGAIN (just like O_NONBLOCK flag). + + Module snd-rawmidi + ------------------ + + This module takes options which change the mapping of devices. + similar to those of the snd-pcm-oss module. + + midi_map - MIDI device number maps assigned to the 1st OSS device. + - Default: 0 + amidi_map - MIDI device number maps assigned to the 2st OSS device. + - Default: 1 + + Common parameters for top sound card modules + -------------------------------------------- + + Each of top level sound card module takes the following options. + + index - index (slot #) of sound card + - Values: 0 through 31 or negative + - If nonnegative, assign that index number + - if negative, interpret as a bitmask of permissible + indices; the first free permitted index is assigned + - Default: -1 + id - card ID (identifier or name) + - Can be up to 15 characters long + - Default: the card type + - A directory by this name is created under /proc/asound/ + containing information about the card + - This ID can be used instead of the index number in + identifying the card + enable - enable card + - Default: enabled, for PCI and ISA PnP cards + + Module snd-adlib + ---------------- + + Module for AdLib FM cards. + + port - port # for OPL chip + + This module supports multiple cards. It does not support autoprobe, so + the port must be specified. For actual AdLib FM cards it will be 0x388. + Note that this card does not have PCM support and no mixer; only FM + synthesis. + + Make sure you have "sbiload" from the alsa-tools package available and, + after loading the module, find out the assigned ALSA sequencer port + number through "sbiload -l". Example output: + + Port Client name Port name + 64:0 OPL2 FM synth OPL2 FM Port + + Load the std.sb and drums.sb patches also supplied by sbiload: + + sbiload -p 64:0 std.sb drums.sb + + If you use this driver to drive an OPL3, you can use std.o3 and drums.o3 + instead. To have the card produce sound, use aplaymidi from alsa-utils: + + aplaymidi -p 64:0 foo.mid + + Module snd-ad1816a + ------------------ + + Module for sound cards based on Analog Devices AD1816A/AD1815 ISA chips. + + clockfreq - Clock frequency for AD1816A chip (default = 0, 33000Hz) + + This module supports multiple cards, autoprobe and PnP. + + Module snd-ad1848 + ----------------- + + Module for sound cards based on AD1848/AD1847/CS4248 ISA chips. + + port - port # for AD1848 chip + irq - IRQ # for AD1848 chip + dma1 - DMA # for AD1848 chip (0,1,3) + + This module supports multiple cards. It does not support autoprobe + thus main port must be specified!!! Other ports are optional. + + The power-management is supported. + + Module snd-ad1889 + ----------------- + + Module for Analog Devices AD1889 chips. + + ac97_quirk - AC'97 workaround for strange hardware + See the description of intel8x0 module for details. + + This module supports multiple cards. + + Module snd-ali5451 + ------------------ + + Module for ALi M5451 PCI chip. + + pcm_channels - Number of hardware channels assigned for PCM + spdif - Support SPDIF I/O + - Default: disabled + + This module supports one chip and autoprobe. + + The power-management is supported. + + Module snd-als100 + ----------------- + + Module for sound cards based on Avance Logic ALS100/ALS120 ISA chips. + + This module supports multiple cards, autoprobe and PnP. + + The power-management is supported. + + Module snd-als300 + ----------------- + + Module for Avance Logic ALS300 and ALS300+ + + This module supports multiple cards. + + The power-management is supported. + + Module snd-als4000 + ------------------ + + Module for sound cards based on Avance Logic ALS4000 PCI chip. + + joystick_port - port # for legacy joystick support. + 0 = disabled (default), 1 = auto-detect + + This module supports multiple cards, autoprobe and PnP. + + The power-management is supported. + + Module snd-asihpi + ----------------- + + Module for AudioScience ASI soundcards + + enable_hpi_hwdep - enable HPI hwdep for AudioScience soundcard + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-atiixp + ----------------- + + Module for ATI IXP 150/200/250/400 AC97 controllers. + + ac97_clock - AC'97 clock (default = 48000) + ac97_quirk - AC'97 workaround for strange hardware + See "AC97 Quirk Option" section below. + ac97_codec - Workaround to specify which AC'97 codec + instead of probing. If this works for you + file a bug with your `lspci -vn` output. + -2 -- Force probing. + -1 -- Default behavior. + 0-2 -- Use the specified codec. + spdif_aclink - S/PDIF transfer over AC-link (default = 1) + + This module supports one card and autoprobe. + + ATI IXP has two different methods to control SPDIF output. One is + over AC-link and another is over the "direct" SPDIF output. The + implementation depends on the motherboard, and you'll need to + choose the correct one via spdif_aclink module option. + + The power-management is supported. + + Module snd-atiixp-modem + ----------------------- + + Module for ATI IXP 150/200/250 AC97 modem controllers. + + This module supports one card and autoprobe. + + Note: The default index value of this module is -2, i.e. the first + slot is excluded. + + The power-management is supported. + + Module snd-au8810, snd-au8820, snd-au8830 + ----------------------------------------- + + Module for Aureal Vortex, Vortex2 and Advantage device. + + pcifix - Control PCI workarounds + 0 = Disable all workarounds + 1 = Force the PCI latency of the Aureal card to 0xff + 2 = Force the Extend PCI#2 Internal Master for Efficient + Handling of Dummy Requests on the VIA KT133 AGP Bridge + 3 = Force both settings + 255 = Autodetect what is required (default) + + This module supports all ADB PCM channels, ac97 mixer, SPDIF, hardware + EQ, mpu401, gameport. A3D and wavetable support are still in development. + Development and reverse engineering work is being coordinated at + http://savannah.nongnu.org/projects/openvortex/ + SPDIF output has a copy of the AC97 codec output, unless you use the + "spdif" pcm device, which allows raw data passthru. + The hardware EQ hardware and SPDIF is only present in the Vortex2 and + Advantage. + + Note: Some ALSA mixer applications don't handle the SPDIF sample rate + control correctly. If you have problems regarding this, try + another ALSA compliant mixer (alsamixer works). + + Module snd-azt1605 + ------------------ + + Module for Aztech Sound Galaxy soundcards based on the Aztech AZT1605 + chipset. + + port - port # for BASE (0x220,0x240,0x260,0x280) + wss_port - port # for WSS (0x530,0x604,0xe80,0xf40) + irq - IRQ # for WSS (7,9,10,11) + dma1 - DMA # for WSS playback (0,1,3) + dma2 - DMA # for WSS capture (0,1), -1 = disabled (default) + mpu_port - port # for MPU-401 UART (0x300,0x330), -1 = disabled (default) + mpu_irq - IRQ # for MPU-401 UART (3,5,7,9), -1 = disabled (default) + fm_port - port # for OPL3 (0x388), -1 = disabled (default) + + This module supports multiple cards. It does not support autoprobe: port, + wss_port, irq and dma1 have to be specified. The other values are + optional. + + "port" needs to match the BASE ADDRESS jumper on the card (0x220 or 0x240) + or the value stored in the card's EEPROM for cards that have an EEPROM and + their "CONFIG MODE" jumper set to "EEPROM SETTING". The other values can + be chosen freely from the options enumerated above. + + If dma2 is specified and different from dma1, the card will operate in + full-duplex mode. When dma1=3, only dma2=0 is valid and the only way to + enable capture since only channels 0 and 1 are available for capture. + + Generic settings are "port=0x220 wss_port=0x530 irq=10 dma1=1 dma2=0 + mpu_port=0x330 mpu_irq=9 fm_port=0x388". + + Whatever IRQ and DMA channels you pick, be sure to reserve them for + legacy ISA in your BIOS. + + Module snd-azt2316 + ------------------ + + Module for Aztech Sound Galaxy soundcards based on the Aztech AZT2316 + chipset. + + port - port # for BASE (0x220,0x240,0x260,0x280) + wss_port - port # for WSS (0x530,0x604,0xe80,0xf40) + irq - IRQ # for WSS (7,9,10,11) + dma1 - DMA # for WSS playback (0,1,3) + dma2 - DMA # for WSS capture (0,1), -1 = disabled (default) + mpu_port - port # for MPU-401 UART (0x300,0x330), -1 = disabled (default) + mpu_irq - IRQ # for MPU-401 UART (5,7,9,10), -1 = disabled (default) + fm_port - port # for OPL3 (0x388), -1 = disabled (default) + + This module supports multiple cards. It does not support autoprobe: port, + wss_port, irq and dma1 have to be specified. The other values are + optional. + + "port" needs to match the BASE ADDRESS jumper on the card (0x220 or 0x240) + or the value stored in the card's EEPROM for cards that have an EEPROM and + their "CONFIG MODE" jumper set to "EEPROM SETTING". The other values can + be chosen freely from the options enumerated above. + + If dma2 is specified and different from dma1, the card will operate in + full-duplex mode. When dma1=3, only dma2=0 is valid and the only way to + enable capture since only channels 0 and 1 are available for capture. + + Generic settings are "port=0x220 wss_port=0x530 irq=10 dma1=1 dma2=0 + mpu_port=0x330 mpu_irq=9 fm_port=0x388". + + Whatever IRQ and DMA channels you pick, be sure to reserve them for + legacy ISA in your BIOS. + + Module snd-aw2 + -------------- + + Module for Audiowerk2 sound card + + This module supports multiple cards. + + Module snd-azt2320 + ------------------ + + Module for sound cards based on Aztech System AZT2320 ISA chip (PnP only). + + This module supports multiple cards, PnP and autoprobe. + + The power-management is supported. + + Module snd-azt3328 + ------------------ + + Module for sound cards based on Aztech AZF3328 PCI chip. + + joystick - Enable joystick (default off) + + This module supports multiple cards. + + Module snd-bt87x + ---------------- + + Module for video cards based on Bt87x chips. + + digital_rate - Override the default digital rate (Hz) + load_all - Load the driver even if the card model isn't known + + This module supports multiple cards. + + Note: The default index value of this module is -2, i.e. the first + slot is excluded. + + Module snd-ca0106 + ----------------- + + Module for Creative Audigy LS and SB Live 24bit + + This module supports multiple cards. + + + Module snd-cmi8330 + ------------------ + + Module for sound cards based on C-Media CMI8330 ISA chips. + + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + wssport - port # for CMI8330 chip (WSS) + wssirq - IRQ # for CMI8330 chip (WSS) + wssdma - first DMA # for CMI8330 chip (WSS) + sbport - port # for CMI8330 chip (SB16) + sbirq - IRQ # for CMI8330 chip (SB16) + sbdma8 - 8bit DMA # for CMI8330 chip (SB16) + sbdma16 - 16bit DMA # for CMI8330 chip (SB16) + fmport - (optional) OPL3 I/O port + mpuport - (optional) MPU401 I/O port + mpuirq - (optional) MPU401 irq # + + This module supports multiple cards and autoprobe. + + The power-management is supported. + + Module snd-cmipci + ----------------- + + Module for C-Media CMI8338/8738/8768/8770 PCI sound cards. + + mpu_port - port address of MIDI interface (8338 only): + 0x300,0x310,0x320,0x330 = legacy port, + 0 = disable (default) + fm_port - port address of OPL-3 FM synthesizer (8x38 only): + 0x388 = legacy port, + 1 = integrated PCI port (default on 8738), + 0 = disable + soft_ac3 - Software-conversion of raw SPDIF packets (model 033 only) + (default = 1) + joystick_port - Joystick port address (0 = disable, 1 = auto-detect) + + This module supports autoprobe and multiple cards. + + The power-management is supported. + + Module snd-cs4231 + ----------------- + + Module for sound cards based on CS4231 ISA chips. + + port - port # for CS4231 chip + mpu_port - port # for MPU-401 UART (optional), -1 = disable + irq - IRQ # for CS4231 chip + mpu_irq - IRQ # for MPU-401 UART + dma1 - first DMA # for CS4231 chip + dma2 - second DMA # for CS4231 chip + + This module supports multiple cards. This module does not support autoprobe + thus main port must be specified!!! Other ports are optional. + + The power-management is supported. + + Module snd-cs4236 + ----------------- + + Module for sound cards based on CS4232/CS4232A, + CS4235/CS4236/CS4236B/CS4237B/ + CS4238B/CS4239 ISA chips. + + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - port # for CS4236 chip (PnP setup - 0x534) + cport - control port # for CS4236 chip (PnP setup - 0x120,0x210,0xf00) + mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable + fm_port - FM port # for CS4236 chip (PnP setup - 0x388), -1 = disable + irq - IRQ # for CS4236 chip (5,7,9,11,12,15) + mpu_irq - IRQ # for MPU-401 UART (9,11,12,15) + dma1 - first DMA # for CS4236 chip (0,1,3) + dma2 - second DMA # for CS4236 chip (0,1,3), -1 = disable + + This module supports multiple cards. This module does not support autoprobe + (if ISA PnP is not used) thus main port and control port must be + specified!!! Other ports are optional. + + The power-management is supported. + + This module is aliased as snd-cs4232 since it provides the old + snd-cs4232 functionality, too. + + Module snd-cs4281 + ----------------- + + Module for Cirrus Logic CS4281 soundchip. + + dual_codec - Secondary codec ID (0 = disable, default) + + This module supports multiple cards. + + The power-management is supported. + + Module snd-cs46xx + ----------------- + + Module for PCI sound cards based on CS4610/CS4612/CS4614/CS4615/CS4622/ + CS4624/CS4630/CS4280 PCI chips. + + external_amp - Force to enable external amplifier. + thinkpad - Force to enable Thinkpad's CLKRUN control. + mmap_valid - Support OSS mmap mode (default = 0). + + This module supports multiple cards and autoprobe. + Usually external amp and CLKRUN controls are detected automatically + from PCI sub vendor/device ids. If they don't work, give the options + above explicitly. + + The power-management is supported. + + Module snd-cs5530 + _________________ + + Module for Cyrix/NatSemi Geode 5530 chip. + + Module snd-cs5535audio + ---------------------- + + Module for multifunction CS5535 companion PCI device + + The power-management is supported. + + Module snd-ctxfi + ---------------- + + Module for Creative Sound Blaster X-Fi boards (20k1 / 20k2 chips) + * Creative Sound Blaster X-Fi Titanium Fatal1ty Champion Series + * Creative Sound Blaster X-Fi Titanium Fatal1ty Professional Series + * Creative Sound Blaster X-Fi Titanium Professional Audio + * Creative Sound Blaster X-Fi Titanium + * Creative Sound Blaster X-Fi Elite Pro + * Creative Sound Blaster X-Fi Platinum + * Creative Sound Blaster X-Fi Fatal1ty + * Creative Sound Blaster X-Fi XtremeGamer + * Creative Sound Blaster X-Fi XtremeMusic + + reference_rate - reference sample rate, 44100 or 48000 (default) + multiple - multiple to ref. sample rate, 1 or 2 (default) + subsystem - override the PCI SSID for probing; the value + consists of SSVID << 16 | SSDID. The default is + zero, which means no override. + + This module supports multiple cards. + + Module snd-darla20 + ------------------ + + Module for Echoaudio Darla20 + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-darla24 + ------------------ + + Module for Echoaudio Darla24 + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-dt019x + ----------------- + + Module for Diamond Technologies DT-019X / Avance Logic ALS-007 (PnP + only) + + This module supports multiple cards. This module is enabled only with + ISA PnP support. + + The power-management is supported. + + Module snd-dummy + ---------------- + + Module for the dummy sound card. This "card" doesn't do any output + or input, but you may use this module for any application which + requires a sound card (like RealPlayer). + + pcm_devs - Number of PCM devices assigned to each card + (default = 1, up to 4) + pcm_substreams - Number of PCM substreams assigned to each PCM + (default = 8, up to 128) + hrtimer - Use hrtimer (=1, default) or system timer (=0) + fake_buffer - Fake buffer allocations (default = 1) + + When multiple PCM devices are created, snd-dummy gives different + behavior to each PCM device: + 0 = interleaved with mmap support + 1 = non-interleaved with mmap support + 2 = interleaved without mmap + 3 = non-interleaved without mmap + + As default, snd-dummy drivers doesn't allocate the real buffers + but either ignores read/write or mmap a single dummy page to all + buffer pages, in order to save the resouces. If your apps need + the read/ written buffer data to be consistent, pass fake_buffer=0 + option. + + The power-management is supported. + + Module snd-echo3g + ----------------- + + Module for Echoaudio 3G cards (Gina3G/Layla3G) + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-emu10k1 + ------------------ + + Module for EMU10K1/EMU10k2 based PCI sound cards. + * Sound Blaster Live! + * Sound Blaster PCI 512 + * Emu APS (partially supported) + * Sound Blaster Audigy + + extin - bitmap of available external inputs for FX8010 (see bellow) + extout - bitmap of available external outputs for FX8010 (see bellow) + seq_ports - allocated sequencer ports (4 by default) + max_synth_voices - limit of voices used for wavetable (64 by default) + max_buffer_size - specifies the maximum size of wavetable/pcm buffers + given in MB unit. Default value is 128. + enable_ir - enable IR + + This module supports multiple cards and autoprobe. + + Input & Output configurations [extin/extout] + * Creative Card wo/Digital out [0x0003/0x1f03] + * Creative Card w/Digital out [0x0003/0x1f0f] + * Creative Card w/Digital CD in [0x000f/0x1f0f] + * Creative Card wo/Digital out + LiveDrive [0x3fc3/0x1fc3] + * Creative Card w/Digital out + LiveDrive [0x3fc3/0x1fcf] + * Creative Card w/Digital CD in + LiveDrive [0x3fcf/0x1fcf] + * Creative Card wo/Digital out + Digital I/O 2 [0x0fc3/0x1f0f] + * Creative Card w/Digital out + Digital I/O 2 [0x0fc3/0x1f0f] + * Creative Card w/Digital CD in + Digital I/O 2 [0x0fcf/0x1f0f] + * Creative Card 5.1/w Digital out + LiveDrive [0x3fc3/0x1fff] + * Creative Card 5.1 (c) 2003 [0x3fc3/0x7cff] + * Creative Card all ins and outs [0x3fff/0x7fff] + + The power-management is supported. + + Module snd-emu10k1x + ------------------- + + Module for Creative Emu10k1X (SB Live Dell OEM version) + + This module supports multiple cards. + + Module snd-ens1370 + ------------------ + + Module for Ensoniq AudioPCI ES1370 PCI sound cards. + * SoundBlaster PCI 64 + * SoundBlaster PCI 128 + + joystick - Enable joystick (default off) + + This module supports multiple cards and autoprobe. + + The power-management is supported. + + Module snd-ens1371 + ------------------ + + Module for Ensoniq AudioPCI ES1371 PCI sound cards. + * SoundBlaster PCI 64 + * SoundBlaster PCI 128 + * SoundBlaster Vibra PCI + + joystick_port - port # for joystick (0x200,0x208,0x210,0x218), + 0 = disable (default), 1 = auto-detect + + This module supports multiple cards and autoprobe. + + The power-management is supported. + + Module snd-es1688 + ----------------- + + Module for ESS AudioDrive ES-1688 and ES-688 sound cards. + + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default) + mpu_irq - IRQ # for MPU-401 port (5,7,9,10) + fm_port - port # for OPL3 (option; share the same port as default) + + with isapnp=0, the following additional options are available: + port - port # for ES-1688 chip (0x220,0x240,0x260) + irq - IRQ # for ES-1688 chip (5,7,9,10) + dma8 - DMA # for ES-1688 chip (0,1,3) + + This module supports multiple cards and autoprobe (without MPU-401 port) + and PnP with the ES968 chip. + + Module snd-es18xx + ----------------- + + Module for ESS AudioDrive ES-18xx sound cards. + + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - port # for ES-18xx chip (0x220,0x240,0x260) + mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default) + fm_port - port # for FM (optional, not used) + irq - IRQ # for ES-18xx chip (5,7,9,10) + dma1 - first DMA # for ES-18xx chip (0,1,3) + dma2 - first DMA # for ES-18xx chip (0,1,3) + + This module supports multiple cards, ISA PnP and autoprobe (without MPU-401 + port if native ISA PnP routines are not used). + When dma2 is equal with dma1, the driver works as half-duplex. + + The power-management is supported. + + Module snd-es1938 + ----------------- + + Module for sound cards based on ESS Solo-1 (ES1938,ES1946) chips. + + This module supports multiple cards and autoprobe. + + The power-management is supported. + + Module snd-es1968 + ----------------- + + Module for sound cards based on ESS Maestro-1/2/2E (ES1968/ES1978) chips. + + total_bufsize - total buffer size in kB (1-4096kB) + pcm_substreams_p - playback channels (1-8, default=2) + pcm_substreams_c - capture channels (1-8, default=0) + clock - clock (0 = auto-detection) + use_pm - support the power-management (0 = off, 1 = on, + 2 = auto (default)) + enable_mpu - enable MPU401 (0 = off, 1 = on, 2 = auto (default)) + joystick - enable joystick (default off) + + This module supports multiple cards and autoprobe. + + The power-management is supported. + + Module snd-fm801 + ---------------- + + Module for ForteMedia FM801 based PCI sound cards. + + tea575x_tuner - Enable TEA575x tuner + - 1 = MediaForte 256-PCS + - 2 = MediaForte 256-PCPR + - 3 = MediaForte 64-PCR + - High 16-bits are video (radio) device number + 1 + - example: 0x10002 (MediaForte 256-PCPR, device 1) + + This module supports multiple cards and autoprobe. + + The power-management is supported. + + Module snd-gina20 + ----------------- + + Module for Echoaudio Gina20 + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-gina24 + ----------------- + + Module for Echoaudio Gina24 + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-gusclassic + --------------------- + + Module for Gravis UltraSound Classic sound card. + + port - port # for GF1 chip (0x220,0x230,0x240,0x250,0x260) + irq - IRQ # for GF1 chip (3,5,9,11,12,15) + dma1 - DMA # for GF1 chip (1,3,5,6,7) + dma2 - DMA # for GF1 chip (1,3,5,6,7,-1=disable) + joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V) + voices - GF1 voices limit (14-32) + pcm_voices - reserved PCM voices + + This module supports multiple cards and autoprobe. + + Module snd-gusextreme + --------------------- + + Module for Gravis UltraSound Extreme (Synergy ViperMax) sound card. + + port - port # for ES-1688 chip (0x220,0x230,0x240,0x250,0x260) + gf1_port - port # for GF1 chip (0x210,0x220,0x230,0x240,0x250,0x260,0x270) + mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable + irq - IRQ # for ES-1688 chip (5,7,9,10) + gf1_irq - IRQ # for GF1 chip (3,5,9,11,12,15) + mpu_irq - IRQ # for MPU-401 port (5,7,9,10) + dma8 - DMA # for ES-1688 chip (0,1,3) + dma1 - DMA # for GF1 chip (1,3,5,6,7) + joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V) + voices - GF1 voices limit (14-32) + pcm_voices - reserved PCM voices + + This module supports multiple cards and autoprobe (without MPU-401 port). + + Module snd-gusmax + ----------------- + + Module for Gravis UltraSound MAX sound card. + + port - port # for GF1 chip (0x220,0x230,0x240,0x250,0x260) + irq - IRQ # for GF1 chip (3,5,9,11,12,15) + dma1 - DMA # for GF1 chip (1,3,5,6,7) + dma2 - DMA # for GF1 chip (1,3,5,6,7,-1=disable) + joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V) + voices - GF1 voices limit (14-32) + pcm_voices - reserved PCM voices + + This module supports multiple cards and autoprobe. + + Module snd-hda-intel + -------------------- + + Module for Intel HD Audio (ICH6, ICH6M, ESB2, ICH7, ICH8, ICH9, ICH10, + PCH, SCH), + ATI SB450, SB600, R600, RS600, RS690, RS780, RV610, RV620, + RV630, RV635, RV670, RV770, + VIA VT8251/VT8237A, + SIS966, ULI M5461 + + [Multiple options for each card instance] + model - force the model name + position_fix - Fix DMA pointer + -1 = system default: choose appropriate one per controller + hardware + 0 = auto: falls back to LPIB when POSBUF doesn't work + 1 = use LPIB + 2 = POSBUF: use position buffer + 3 = VIACOMBO: VIA-specific workaround for capture + 4 = COMBO: use LPIB for playback, auto for capture stream + probe_mask - Bitmask to probe codecs (default = -1, meaning all slots) + When the bit 8 (0x100) is set, the lower 8 bits are used + as the "fixed" codec slots; i.e. the driver probes the + slots regardless what hardware reports back + probe_only - Only probing and no codec initialization (default=off); + Useful to check the initial codec status for debugging + bdl_pos_adj - Specifies the DMA IRQ timing delay in samples. + Passing -1 will make the driver to choose the appropriate + value based on the controller chip. + patch - Specifies the early "patch" files to modify the HD-audio + setup before initializing the codecs. This option is + available only when CONFIG_SND_HDA_PATCH_LOADER=y is set. + See HD-Audio.txt for details. + beep_mode - Selects the beep registration mode (0=off, 1=on); default + value is set via CONFIG_SND_HDA_INPUT_BEEP_MODE kconfig. + + [Single (global) options] + single_cmd - Use single immediate commands to communicate with + codecs (for debugging only) + enable_msi - Enable Message Signaled Interrupt (MSI) (default = off) + power_save - Automatic power-saving timeout (in second, 0 = + disable) + power_save_controller - Support runtime D3 of HD-audio controller + (-1 = on for supported chip (default), false = off, + true = force to on even for unsupported hardware) + align_buffer_size - Force rounding of buffer/period sizes to multiples + of 128 bytes. This is more efficient in terms of memory + access but isn't required by the HDA spec and prevents + users from specifying exact period/buffer sizes. + (default = on) + snoop - Enable/disable snooping (default = on) + + This module supports multiple cards and autoprobe. + + See Documentation/sound/alsa/HD-Audio.txt for more details about + HD-audio driver. + + Each codec may have a model table for different configurations. + If your machine isn't listed there, the default (usually minimal) + configuration is set up. You can pass "model=<name>" option to + specify a certain model in such a case. There are different + models depending on the codec chip. The list of available models + is found in HD-Audio-Models.txt + + The model name "genric" is treated as a special case. When this + model is given, the driver uses the generic codec parser without + "codec-patch". It's sometimes good for testing and debugging. + + If the default configuration doesn't work and one of the above + matches with your device, report it together with alsa-info.sh + output (with --no-upload option) to kernel bugzilla or alsa-devel + ML (see the section "Links and Addresses"). + + power_save and power_save_controller options are for power-saving + mode. See powersave.txt for details. + + Note 2: If you get click noises on output, try the module option + position_fix=1 or 2. position_fix=1 will use the SD_LPIB + register value without FIFO size correction as the current + DMA pointer. position_fix=2 will make the driver to use + the position buffer instead of reading SD_LPIB register. + (Usually SD_LPIB register is more accurate than the + position buffer.) + + position_fix=3 is specific to VIA devices. The position + of the capture stream is checked from both LPIB and POSBUF + values. position_fix=4 is a combination mode, using LPIB + for playback and POSBUF for capture. + + NB: If you get many "azx_get_response timeout" messages at + loading, it's likely a problem of interrupts (e.g. ACPI irq + routing). Try to boot with options like "pci=noacpi". Also, you + can try "single_cmd=1" module option. This will switch the + communication method between HDA controller and codecs to the + single immediate commands instead of CORB/RIRB. Basically, the + single command mode is provided only for BIOS, and you won't get + unsolicited events, too. But, at least, this works independently + from the irq. Remember this is a last resort, and should be + avoided as much as possible... + + MORE NOTES ON "azx_get_response timeout" PROBLEMS: + On some hardwares, you may need to add a proper probe_mask option + to avoid the "azx_get_response timeout" problem above, instead. + This occurs when the access to non-existing or non-working codec slot + (likely a modem one) causes a stall of the communication via HD-audio + bus. You can see which codec slots are probed by enabling + CONFIG_SND_DEBUG_VERBOSE, or simply from the file name of the codec + proc files. Then limit the slots to probe by probe_mask option. + For example, probe_mask=1 means to probe only the first slot, and + probe_mask=4 means only the third slot. + + The power-management is supported. + + Module snd-hdsp + --------------- + + Module for RME Hammerfall DSP audio interface(s) + + This module supports multiple cards. + + Note: The firmware data can be automatically loaded via hotplug + when CONFIG_FW_LOADER is set. Otherwise, you need to load + the firmware via hdsploader utility included in alsa-tools + package. + The firmware data is found in alsa-firmware package. + + Note: snd-page-alloc module does the job which snd-hammerfall-mem + module did formerly. It will allocate the buffers in advance + when any HDSP cards are found. To make the buffer + allocation sure, load snd-page-alloc module in the early + stage of boot sequence. See "Early Buffer Allocation" + section. + + Module snd-hdspm + ---------------- + + Module for RME HDSP MADI board. + + precise_ptr - Enable precise pointer, or disable. + line_outs_monitor - Send playback streams to analog outs by default. + enable_monitor - Enable Analog Out on Channel 63/64 by default. + + See hdspm.txt for details. + + Module snd-ice1712 + ------------------ + + Module for Envy24 (ICE1712) based PCI sound cards. + * MidiMan M Audio Delta 1010 + * MidiMan M Audio Delta 1010LT + * MidiMan M Audio Delta DiO 2496 + * MidiMan M Audio Delta 66 + * MidiMan M Audio Delta 44 + * MidiMan M Audio Delta 410 + * MidiMan M Audio Audiophile 2496 + * TerraTec EWS 88MT + * TerraTec EWS 88D + * TerraTec EWX 24/96 + * TerraTec DMX 6Fire + * TerraTec Phase 88 + * Hoontech SoundTrack DSP 24 + * Hoontech SoundTrack DSP 24 Value + * Hoontech SoundTrack DSP 24 Media 7.1 + * Event Electronics, EZ8 + * Digigram VX442 + * Lionstracs, Mediastaton + * Terrasoniq TS 88 + + model - Use the given board model, one of the following: + delta1010, dio2496, delta66, delta44, audiophile, delta410, + delta1010lt, vx442, ewx2496, ews88mt, ews88mt_new, ews88d, + dmx6fire, dsp24, dsp24_value, dsp24_71, ez8, + phase88, mediastation + omni - Omni I/O support for MidiMan M-Audio Delta44/66 + cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transceiver) + in msec resolution, default value is 500 (0.5 sec) + + This module supports multiple cards and autoprobe. Note: The consumer part + is not used with all Envy24 based cards (for example in the MidiMan Delta + serie). + + Note: The supported board is detected by reading EEPROM or PCI + SSID (if EEPROM isn't available). You can override the + model by passing "model" module option in case that the + driver isn't configured properly or you want to try another + type for testing. + + Module snd-ice1724 + ------------------ + + Module for Envy24HT (VT/ICE1724), Envy24PT (VT1720) based PCI sound cards. + * MidiMan M Audio Revolution 5.1 + * MidiMan M Audio Revolution 7.1 + * MidiMan M Audio Audiophile 192 + * AMP Ltd AUDIO2000 + * TerraTec Aureon 5.1 Sky + * TerraTec Aureon 7.1 Space + * TerraTec Aureon 7.1 Universe + * TerraTec Phase 22 + * TerraTec Phase 28 + * AudioTrak Prodigy 7.1 + * AudioTrak Prodigy 7.1 LT + * AudioTrak Prodigy 7.1 XT + * AudioTrak Prodigy 7.1 HIFI + * AudioTrak Prodigy 7.1 HD2 + * AudioTrak Prodigy 192 + * Pontis MS300 + * Albatron K8X800 Pro II + * Chaintech ZNF3-150 + * Chaintech ZNF3-250 + * Chaintech 9CJS + * Chaintech AV-710 + * Shuttle SN25P + * Onkyo SE-90PCI + * Onkyo SE-200PCI + * ESI Juli@ + * ESI Maya44 + * Hercules Fortissimo IV + * EGO-SYS WaveTerminal 192M + + model - Use the given board model, one of the following: + revo51, revo71, amp2000, prodigy71, prodigy71lt, + prodigy71xt, prodigy71hifi, prodigyhd2, prodigy192, + juli, aureon51, aureon71, universe, ap192, k8x800, + phase22, phase28, ms300, av710, se200pci, se90pci, + fortissimo4, sn25p, WT192M, maya44 + + This module supports multiple cards and autoprobe. + + Note: The supported board is detected by reading EEPROM or PCI + SSID (if EEPROM isn't available). You can override the + model by passing "model" module option in case that the + driver isn't configured properly or you want to try another + type for testing. + + Module snd-indigo + ----------------- + + Module for Echoaudio Indigo + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-indigodj + ------------------- + + Module for Echoaudio Indigo DJ + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-indigoio + ------------------- + + Module for Echoaudio Indigo IO + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-intel8x0 + ------------------- + + Module for AC'97 motherboards from Intel and compatibles. + * Intel i810/810E, i815, i820, i830, i84x, MX440 + ICH5, ICH6, ICH7, 6300ESB, ESB2 + * SiS 7012 (SiS 735) + * NVidia NForce, NForce2, NForce3, MCP04, CK804 + CK8, CK8S, MCP501 + * AMD AMD768, AMD8111 + * ALi m5455 + + ac97_clock - AC'97 codec clock base (0 = auto-detect) + ac97_quirk - AC'97 workaround for strange hardware + See "AC97 Quirk Option" section below. + buggy_irq - Enable workaround for buggy interrupts on some + motherboards (default yes on nForce chips, + otherwise off) + buggy_semaphore - Enable workaround for hardwares with buggy + semaphores (e.g. on some ASUS laptops) + (default off) + spdif_aclink - Use S/PDIF over AC-link instead of direct connection + from the controller chip + (0 = off, 1 = on, -1 = default) + + This module supports one chip and autoprobe. + + Note: the latest driver supports auto-detection of chip clock. + if you still encounter too fast playback, specify the clock + explicitly via the module option "ac97_clock=41194". + + Joystick/MIDI ports are not supported by this driver. If your + motherboard has these devices, use the ns558 or snd-mpu401 + modules, respectively. + + The power-management is supported. + + Module snd-intel8x0m + -------------------- + + Module for Intel ICH (i8x0) chipset MC97 modems. + * Intel i810/810E, i815, i820, i830, i84x, MX440 + ICH5, ICH6, ICH7 + * SiS 7013 (SiS 735) + * NVidia NForce, NForce2, NForce2s, NForce3 + * AMD AMD8111 + * ALi m5455 + + ac97_clock - AC'97 codec clock base (0 = auto-detect) + + This module supports one card and autoprobe. + + Note: The default index value of this module is -2, i.e. the first + slot is excluded. + + The power-management is supported. + + Module snd-interwave + -------------------- + + Module for Gravis UltraSound PnP, Dynasonic 3-D/Pro, STB Sound Rage 32 + and other sound cards based on AMD InterWave (tm) chip. + + joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V) + midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default) + pcm_voices - reserved PCM voices for the synthesizer (default 2) + effect - 1 = InterWave effects enable (default 0); + requires 8 voices + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260) + irq - IRQ # for InterWave chip (3,5,9,11,12,15) + dma1 - DMA # for InterWave chip (0,1,3,5,6,7) + dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable) + + This module supports multiple cards, autoprobe and ISA PnP. + + Module snd-interwave-stb + ------------------------ + + Module for UltraSound 32-Pro (sound card from STB used by Compaq) + and other sound cards based on AMD InterWave (tm) chip with TEA6330T + circuit for extended control of bass, treble and master volume. + + joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V) + midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default) + pcm_voices - reserved PCM voices for the synthesizer (default 2) + effect - 1 = InterWave effects enable (default 0); + requires 8 voices + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260) + port_tc - tone control (i2c bus) port # for TEA6330T chip (0x350,0x360,0x370,0x380) + irq - IRQ # for InterWave chip (3,5,9,11,12,15) + dma1 - DMA # for InterWave chip (0,1,3,5,6,7) + dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable) + + This module supports multiple cards, autoprobe and ISA PnP. + + Module snd-jazz16 + ------------------- + + Module for Media Vision Jazz16 chipset. The chipset consists of 3 chips: + MVD1216 + MVA416 + MVA514. + + port - port # for SB DSP chip (0x210,0x220,0x230,0x240,0x250,0x260) + irq - IRQ # for SB DSP chip (3,5,7,9,10,15) + dma8 - DMA # for SB DSP chip (1,3) + dma16 - DMA # for SB DSP chip (5,7) + mpu_port - MPU-401 port # (0x300,0x310,0x320,0x330) + mpu_irq - MPU-401 irq # (2,3,5,7) + + This module supports multiple cards. + + Module snd-korg1212 + ------------------- + + Module for Korg 1212 IO PCI card + + This module supports multiple cards. + + Module snd-layla20 + ------------------ + + Module for Echoaudio Layla20 + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-layla24 + ------------------ + + Module for Echoaudio Layla24 + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-lola + --------------- + + Module for Digigram Lola PCI-e boards + + This module supports multiple cards. + + Module snd-lx6464es + ------------------- + + Module for Digigram LX6464ES boards + + This module supports multiple cards. + + Module snd-maestro3 + ------------------- + + Module for Allegro/Maestro3 chips + + external_amp - enable external amp (enabled by default) + amp_gpio - GPIO pin number for external amp (0-15) or + -1 for default pin (8 for allegro, 1 for + others) + + This module supports autoprobe and multiple chips. + + Note: the binding of amplifier is dependent on hardware. + If there is no sound even though all channels are unmuted, try to + specify other gpio connection via amp_gpio option. + For example, a Panasonic notebook might need "amp_gpio=0x0d" + option. + + The power-management is supported. + + Module snd-mia + --------------- + + Module for Echoaudio Mia + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-miro + --------------- + + Module for Miro soundcards: miroSOUND PCM 1 pro, + miroSOUND PCM 12, + miroSOUND PCM 20 Radio. + + port - Port # (0x530,0x604,0xe80,0xf40) + irq - IRQ # (5,7,9,10,11) + dma1 - 1st dma # (0,1,3) + dma2 - 2nd dma # (0,1) + mpu_port - MPU-401 port # (0x300,0x310,0x320,0x330) + mpu_irq - MPU-401 irq # (5,7,9,10) + fm_port - FM Port # (0x388) + wss - enable WSS mode + ide - enable onboard ide support + + Module snd-mixart + ----------------- + + Module for Digigram miXart8 sound cards. + + This module supports multiple cards. + Note: One miXart8 board will be represented as 4 alsa cards. + See MIXART.txt for details. + + When the driver is compiled as a module and the hotplug firmware + is supported, the firmware data is loaded via hotplug automatically. + Install the necessary firmware files in alsa-firmware package. + When no hotplug fw loader is available, you need to load the + firmware via mixartloader utility in alsa-tools package. + + Module snd-mona + --------------- + + Module for Echoaudio Mona + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + + Module snd-mpu401 + ----------------- + + Module for MPU-401 UART devices. + + port - port number or -1 (disable) + irq - IRQ number or -1 (disable) + pnp - PnP detection - 0 = disable, 1 = enable (default) + + This module supports multiple devices and PnP. + + Module snd-msnd-classic + ----------------------- + + Module for Turtle Beach MultiSound Classic, Tahiti or Monterey + soundcards. + + io - Port # for msnd-classic card + irq - IRQ # for msnd-classic card + mem - Memory address (0xb0000, 0xc8000, 0xd0000, 0xd8000, + 0xe0000 or 0xe8000) + write_ndelay - enable write ndelay (default = 1) + calibrate_signal - calibrate signal (default = 0) + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + digital - Digital daughterboard present (default = 0) + cfg - Config port (0x250, 0x260 or 0x270) default = PnP + reset - Reset all devices + mpu_io - MPU401 I/O port + mpu_irq - MPU401 irq# + ide_io0 - IDE port #0 + ide_io1 - IDE port #1 + ide_irq - IDE irq# + joystick_io - Joystick I/O port + + The driver requires firmware files "turtlebeach/msndinit.bin" and + "turtlebeach/msndperm.bin" in the proper firmware directory. + + See Documentation/sound/oss/MultiSound for important information + about this driver. Note that it has been discontinued, but the + Voyetra Turtle Beach knowledge base entry for it is still available + at + http://www.turtlebeach.com + + Module snd-msnd-pinnacle + ------------------------ + + Module for Turtle Beach MultiSound Pinnacle/Fiji soundcards. + + io - Port # for pinnacle/fiji card + irq - IRQ # for pinnalce/fiji card + mem - Memory address (0xb0000, 0xc8000, 0xd0000, 0xd8000, + 0xe0000 or 0xe8000) + write_ndelay - enable write ndelay (default = 1) + calibrate_signal - calibrate signal (default = 0) + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + The driver requires firmware files "turtlebeach/pndspini.bin" and + "turtlebeach/pndsperm.bin" in the proper firmware directory. + + Module snd-mtpav + ---------------- + + Module for MOTU MidiTimePiece AV multiport MIDI (on the parallel + port). + + port - I/O port # for MTPAV (0x378,0x278, default=0x378) + irq - IRQ # for MTPAV (7,5, default=7) + hwports - number of supported hardware ports, default=8. + + Module supports only 1 card. This module has no enable option. + + Module snd-mts64 + ---------------- + + Module for Ego Systems (ESI) Miditerminal 4140 + + This module supports multiple devices. + Requires parport (CONFIG_PARPORT). + + Module snd-nm256 + ---------------- + + Module for NeoMagic NM256AV/ZX chips + + playback_bufsize - max playback frame size in kB (4-128kB) + capture_bufsize - max capture frame size in kB (4-128kB) + force_ac97 - 0 or 1 (disabled by default) + buffer_top - specify buffer top address + use_cache - 0 or 1 (disabled by default) + vaio_hack - alias buffer_top=0x25a800 + reset_workaround - enable AC97 RESET workaround for some laptops + reset_workaround2 - enable extended AC97 RESET workaround for some + other laptops + + This module supports one chip and autoprobe. + + The power-management is supported. + + Note: on some notebooks the buffer address cannot be detected + automatically, or causes hang-up during initialization. + In such a case, specify the buffer top address explicitly via + the buffer_top option. + For example, + Sony F250: buffer_top=0x25a800 + Sony F270: buffer_top=0x272800 + The driver supports only ac97 codec. It's possible to force + to initialize/use ac97 although it's not detected. In such a + case, use force_ac97=1 option - but *NO* guarantee whether it + works! + + Note: The NM256 chip can be linked internally with non-AC97 + codecs. This driver supports only the AC97 codec, and won't work + with machines with other (most likely CS423x or OPL3SAx) chips, + even though the device is detected in lspci. In such a case, try + other drivers, e.g. snd-cs4232 or snd-opl3sa2. Some has ISA-PnP + but some doesn't have ISA PnP. You'll need to specify isapnp=0 + and proper hardware parameters in the case without ISA PnP. + + Note: some laptops need a workaround for AC97 RESET. For the + known hardware like Dell Latitude LS and Sony PCG-F305, this + workaround is enabled automatically. For other laptops with a + hard freeze, you can try reset_workaround=1 option. + + Note: Dell Latitude CSx laptops have another problem regarding + AC97 RESET. On these laptops, reset_workaround2 option is + turned on as default. This option is worth to try if the + previous reset_workaround option doesn't help. + + Note: This driver is really crappy. It's a porting from the + OSS driver, which is a result of black-magic reverse engineering. + The detection of codec will fail if the driver is loaded *after* + X-server as described above. You might be able to force to load + the module, but it may result in hang-up. Hence, make sure that + you load this module *before* X if you encounter this kind of + problem. + + Module snd-opl3sa2 + ------------------ + + Module for Yamaha OPL3-SA2/SA3 sound cards. + + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - control port # for OPL3-SA chip (0x370) + sb_port - SB port # for OPL3-SA chip (0x220,0x240) + wss_port - WSS port # for OPL3-SA chip (0x530,0xe80,0xf40,0x604) + midi_port - port # for MPU-401 UART (0x300,0x330), -1 = disable + fm_port - FM port # for OPL3-SA chip (0x388), -1 = disable + irq - IRQ # for OPL3-SA chip (5,7,9,10) + dma1 - first DMA # for Yamaha OPL3-SA chip (0,1,3) + dma2 - second DMA # for Yamaha OPL3-SA chip (0,1,3), -1 = disable + + This module supports multiple cards and ISA PnP. It does not support + autoprobe (if ISA PnP is not used) thus all ports must be specified!!! + + The power-management is supported. + + Module snd-opti92x-ad1848 + ------------------------- + + Module for sound cards based on OPTi 82c92x and Analog Devices AD1848 chips. + Module works with OAK Mozart cards as well. + + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - port # for WSS chip (0x530,0xe80,0xf40,0x604) + mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330) + fm_port - port # for OPL3 device (0x388) + irq - IRQ # for WSS chip (5,7,9,10,11) + mpu_irq - IRQ # for MPU-401 UART (5,7,9,10) + dma1 - first DMA # for WSS chip (0,1,3) + + This module supports only one card, autoprobe and PnP. + + Module snd-opti92x-cs4231 + ------------------------- + + Module for sound cards based on OPTi 82c92x and Crystal CS4231 chips. + + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - port # for WSS chip (0x530,0xe80,0xf40,0x604) + mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330) + fm_port - port # for OPL3 device (0x388) + irq - IRQ # for WSS chip (5,7,9,10,11) + mpu_irq - IRQ # for MPU-401 UART (5,7,9,10) + dma1 - first DMA # for WSS chip (0,1,3) + dma2 - second DMA # for WSS chip (0,1,3) + + This module supports only one card, autoprobe and PnP. + + Module snd-opti93x + ------------------ + + Module for sound cards based on OPTi 82c93x chips. + + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - port # for WSS chip (0x530,0xe80,0xf40,0x604) + mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330) + fm_port - port # for OPL3 device (0x388) + irq - IRQ # for WSS chip (5,7,9,10,11) + mpu_irq - IRQ # for MPU-401 UART (5,7,9,10) + dma1 - first DMA # for WSS chip (0,1,3) + dma2 - second DMA # for WSS chip (0,1,3) + + This module supports only one card, autoprobe and PnP. + + Module snd-oxygen + ----------------- + + Module for sound cards based on the C-Media CMI8786/8787/8788 chip: + * Asound A-8788 + * Asus Xonar DG/DGX + * AuzenTech X-Meridian + * AuzenTech X-Meridian 2G + * Bgears b-Enspirer + * Club3D Theatron DTS + * HT-Omega Claro (plus) + * HT-Omega Claro halo (XT) + * Kuroutoshikou CMI8787-HG2PCI + * Razer Barracuda AC-1 + * Sondigo Inferno + * TempoTec HiFier Fantasia + * TempoTec HiFier Serenade + + This module supports autoprobe and multiple cards. + + Module snd-pcsp + ----------------- + + Module for internal PC-Speaker. + + nopcm - Disable PC-Speaker PCM sound. Only beeps remain. + nforce_wa - enable NForce chipset workaround. Expect bad sound. + + This module supports system beeps, some kind of PCM playback and + even a few mixer controls. + + Module snd-pcxhr + ---------------- + + Module for Digigram PCXHR boards + + This module supports multiple cards. + + Module snd-portman2x4 + --------------------- + + Module for Midiman Portman 2x4 parallel port MIDI interface + + This module supports multiple cards. + + Module snd-powermac (on ppc only) + --------------------------------- + + Module for PowerMac, iMac and iBook on-board soundchips + + enable_beep - enable beep using PCM (enabled as default) + + Module supports autoprobe a chip. + + Note: the driver may have problems regarding endianness. + + The power-management is supported. + + Module snd-pxa2xx-ac97 (on arm only) + ------------------------------------ + + Module for AC97 driver for the Intel PXA2xx chip + + For ARM architecture only. + + The power-management is supported. + + Module snd-riptide + ------------------ + + Module for Conexant Riptide chip + + joystick_port - Joystick port # (default: 0x200) + mpu_port - MPU401 port # (default: 0x330) + opl3_port - OPL3 port # (default: 0x388) + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + You need to install the firmware file "riptide.hex" to the standard + firmware path (e.g. /lib/firmware). + + Module snd-rme32 + ---------------- + + Module for RME Digi32, Digi32 Pro and Digi32/8 (Sek'd Prodif32, + Prodif96 and Prodif Gold) sound cards. + + This module supports multiple cards. + + Module snd-rme96 + ---------------- + + Module for RME Digi96, Digi96/8 and Digi96/8 PRO/PAD/PST sound cards. + + This module supports multiple cards. + + Module snd-rme9652 + ------------------ + + Module for RME Digi9652 (Hammerfall, Hammerfall-Light) sound cards. + + precise_ptr - Enable precise pointer (doesn't work reliably). + (default = 0) + + This module supports multiple cards. + + Note: snd-page-alloc module does the job which snd-hammerfall-mem + module did formerly. It will allocate the buffers in advance + when any RME9652 cards are found. To make the buffer + allocation sure, load snd-page-alloc module in the early + stage of boot sequence. See "Early Buffer Allocation" + section. + + Module snd-sa11xx-uda1341 (on arm only) + --------------------------------------- + + Module for Philips UDA1341TS on Compaq iPAQ H3600 sound card. + + Module supports only one card. + Module has no enable and index options. + + The power-management is supported. + + Module snd-sb8 + -------------- + + Module for 8-bit SoundBlaster cards: SoundBlaster 1.0, + SoundBlaster 2.0, + SoundBlaster Pro + + port - port # for SB DSP chip (0x220,0x240,0x260) + irq - IRQ # for SB DSP chip (5,7,9,10) + dma8 - DMA # for SB DSP chip (1,3) + + This module supports multiple cards and autoprobe. + + The power-management is supported. + + Module snd-sb16 and snd-sbawe + ----------------------------- + + Module for 16-bit SoundBlaster cards: SoundBlaster 16 (PnP), + SoundBlaster AWE 32 (PnP), + SoundBlaster AWE 64 PnP + + mic_agc - Mic Auto-Gain-Control - 0 = disable, 1 = enable (default) + csp - ASP/CSP chip support - 0 = disable (default), 1 = enable + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + port - port # for SB DSP 4.x chip (0x220,0x240,0x260) + mpu_port - port # for MPU-401 UART (0x300,0x330), -1 = disable + awe_port - base port # for EMU8000 synthesizer (0x620,0x640,0x660) + (snd-sbawe module only) + irq - IRQ # for SB DSP 4.x chip (5,7,9,10) + dma8 - 8-bit DMA # for SB DSP 4.x chip (0,1,3) + dma16 - 16-bit DMA # for SB DSP 4.x chip (5,6,7) + + This module supports multiple cards, autoprobe and ISA PnP. + + Note: To use Vibra16X cards in 16-bit half duplex mode, you must + disable 16bit DMA with dma16 = -1 module parameter. + Also, all Sound Blaster 16 type cards can operate in 16-bit + half duplex mode through 8-bit DMA channel by disabling their + 16-bit DMA channel. + + The power-management is supported. + + Module snd-sc6000 + ----------------- + + Module for Gallant SC-6000 soundcard and later models: SC-6600 + and SC-7000. + + port - Port # (0x220 or 0x240) + mss_port - MSS Port # (0x530 or 0xe80) + irq - IRQ # (5,7,9,10,11) + mpu_irq - MPU-401 IRQ # (5,7,9,10) ,0 - no MPU-401 irq + dma - DMA # (1,3,0) + joystick - Enable gameport - 0 = disable (default), 1 = enable + + This module supports multiple cards. + + This card is also known as Audio Excel DSP 16 or Zoltrix AV302. + + Module snd-sscape + ----------------- + + Module for ENSONIQ SoundScape cards. + + port - Port # (PnP setup) + wss_port - WSS Port # (PnP setup) + irq - IRQ # (PnP setup) + mpu_irq - MPU-401 IRQ # (PnP setup) + dma - DMA # (PnP setup) + dma2 - 2nd DMA # (PnP setup, -1 to disable) + joystick - Enable gameport - 0 = disable (default), 1 = enable + + This module supports multiple cards. + + The driver requires the firmware loader support on kernel. + + Module snd-sun-amd7930 (on sparc only) + -------------------------------------- + + Module for AMD7930 sound chips found on Sparcs. + + This module supports multiple cards. + + Module snd-sun-cs4231 (on sparc only) + ------------------------------------- + + Module for CS4231 sound chips found on Sparcs. + + This module supports multiple cards. + + Module snd-sun-dbri (on sparc only) + ----------------------------------- + + Module for DBRI sound chips found on Sparcs. + + This module supports multiple cards. + + Module snd-wavefront + -------------------- + + Module for Turtle Beach Maui, Tropez and Tropez+ sound cards. + + use_cs4232_midi - Use CS4232 MPU-401 interface + (inaccessibly located inside your computer) + isapnp - ISA PnP detection - 0 = disable, 1 = enable (default) + + with isapnp=0, the following options are available: + + cs4232_pcm_port - Port # for CS4232 PCM interface. + cs4232_pcm_irq - IRQ # for CS4232 PCM interface (5,7,9,11,12,15). + cs4232_mpu_port - Port # for CS4232 MPU-401 interface. + cs4232_mpu_irq - IRQ # for CS4232 MPU-401 interface (9,11,12,15). + ics2115_port - Port # for ICS2115 + ics2115_irq - IRQ # for ICS2115 + fm_port - FM OPL-3 Port # + dma1 - DMA1 # for CS4232 PCM interface. + dma2 - DMA2 # for CS4232 PCM interface. + + The below are options for wavefront_synth features: + wf_raw - Assume that we need to boot the OS (default:no) + If yes, then during driver loading, the state of the board is + ignored, and we reset the board and load the firmware anyway. + fx_raw - Assume that the FX process needs help (default:yes) + If false, we'll leave the FX processor in whatever state it is + when the driver is loaded. The default is to download the + microprogram and associated coefficients to set it up for + "default" operation, whatever that means. + debug_default - Debug parameters for card initialization + wait_usecs - How long to wait without sleeping, usecs + (default:150) + This magic number seems to give pretty optimal throughput + based on my limited experimentation. + If you want to play around with it and find a better value, be + my guest. Remember, the idea is to get a number that causes us + to just busy wait for as many WaveFront commands as possible, + without coming up with a number so large that we hog the whole + CPU. + Specifically, with this number, out of about 134,000 status + waits, only about 250 result in a sleep. + sleep_interval - How long to sleep when waiting for reply + (default: 100) + sleep_tries - How many times to try sleeping during a wait + (default: 50) + ospath - Pathname to processed ICS2115 OS firmware + (default:wavefront.os) + The path name of the ISC2115 OS firmware. In the recent + version, it's handled via firmware loader framework, so it + must be installed in the proper path, typically, + /lib/firmware. + reset_time - How long to wait for a reset to take effect + (default:2) + ramcheck_time - How many seconds to wait for the RAM test + (default:20) + osrun_time - How many seconds to wait for the ICS2115 OS + (default:10) + + This module supports multiple cards and ISA PnP. + + Note: the firmware file "wavefront.os" was located in the earlier + version in /etc. Now it's loaded via firmware loader, and + must be in the proper firmware path, such as /lib/firmware. + Copy (or symlink) the file appropriately if you get an error + regarding firmware downloading after upgrading the kernel. + + Module snd-sonicvibes + --------------------- + + Module for S3 SonicVibes PCI sound cards. + * PINE Schubert 32 PCI + + reverb - Reverb Enable - 1 = enable, 0 = disable (default) + - SoundCard must have onboard SRAM for this. + mge - Mic Gain Enable - 1 = enable, 0 = disable (default) + + This module supports multiple cards and autoprobe. + + Module snd-serial-u16550 + ------------------------ + + Module for UART16550A serial MIDI ports. + + port - port # for UART16550A chip + irq - IRQ # for UART16550A chip, -1 = poll mode + speed - speed in bauds (9600,19200,38400,57600,115200) + 38400 = default + base - base for divisor in bauds (57600,115200,230400,460800) + 115200 = default + outs - number of MIDI ports in a serial port (1-4) + 1 = default + adaptor - Type of adaptor. + 0 = Soundcanvas, 1 = MS-124T, 2 = MS-124W S/A, + 3 = MS-124W M/B, 4 = Generic + + This module supports multiple cards. This module does not support autoprobe + thus the main port must be specified!!! Other options are optional. + + Module snd-trident + ------------------ + + Module for Trident 4DWave DX/NX sound cards. + * Best Union Miss Melody 4DWave PCI + * HIS 4DWave PCI + * Warpspeed ONSpeed 4DWave PCI + * AzTech PCI 64-Q3D + * Addonics SV 750 + * CHIC True Sound 4Dwave + * Shark Predator4D-PCI + * Jaton SonicWave 4D + * SiS SI7018 PCI Audio + * Hoontech SoundTrack Digital 4DWave NX + + pcm_channels - max channels (voices) reserved for PCM + wavetable_size - max wavetable size in kB (4-?kb) + + This module supports multiple cards and autoprobe. + + The power-management is supported. + + Module snd-ua101 + ---------------- + + Module for the Edirol UA-101/UA-1000 audio/MIDI interfaces. + + This module supports multiple devices, autoprobe and hotplugging. + + Module snd-usb-audio + -------------------- + + Module for USB audio and USB MIDI devices. + + vid - Vendor ID for the device (optional) + pid - Product ID for the device (optional) + nrpacks - Max. number of packets per URB (default: 8) + device_setup - Device specific magic number (optional) + - Influence depends on the device + - Default: 0x0000 + ignore_ctl_error - Ignore any USB-controller regarding mixer + interface (default: no) + + This module supports multiple devices, autoprobe and hotplugging. + + NB: nrpacks parameter can be modified dynamically via sysfs. + Don't put the value over 20. Changing via sysfs has no sanity + check. + NB: ignore_ctl_error=1 may help when you get an error at accessing + the mixer element such as URB error -22. This happens on some + buggy USB device or the controller. + + Module snd-usb-caiaq + -------------------- + + Module for caiaq UB audio interfaces, + * Native Instruments RigKontrol2 + * Native Instruments Kore Controller + * Native Instruments Audio Kontrol 1 + * Native Instruments Audio 8 DJ + + This module supports multiple devices, autoprobe and hotplugging. + + Module snd-usb-usx2y + -------------------- + + Module for Tascam USB US-122, US-224 and US-428 devices. + + This module supports multiple devices, autoprobe and hotplugging. + + Note: you need to load the firmware via usx2yloader utility included + in alsa-tools and alsa-firmware packages. + + Module snd-via82xx + ------------------ + + Module for AC'97 motherboards based on VIA 82C686A/686B, 8233, + 8233A, 8233C, 8235, 8237 (south) bridge. + + mpu_port - 0x300,0x310,0x320,0x330, otherwise obtain BIOS setup + [VIA686A/686B only] + joystick - Enable joystick (default off) [VIA686A/686B only] + ac97_clock - AC'97 codec clock base (default 48000Hz) + dxs_support - support DXS channels, + 0 = auto (default), 1 = enable, 2 = disable, + 3 = 48k only, 4 = no VRA, 5 = enable any sample + rate and different sample rates on different + channels + [VIA8233/C, 8235, 8237 only] + ac97_quirk - AC'97 workaround for strange hardware + See "AC97 Quirk Option" section below. + + This module supports one chip and autoprobe. + + Note: on some SMP motherboards like MSI 694D the interrupts might + not be generated properly. In such a case, please try to + set the SMP (or MPS) version on BIOS to 1.1 instead of + default value 1.4. Then the interrupt number will be + assigned under 15. You might also upgrade your BIOS. + + Note: VIA8233/5/7 (not VIA8233A) can support DXS (direct sound) + channels as the first PCM. On these channels, up to 4 + streams can be played at the same time, and the controller + can perform sample rate conversion with separate rates for + each channel. + As default (dxs_support = 0), 48k fixed rate is chosen + except for the known devices since the output is often + noisy except for 48k on some mother boards due to the + bug of BIOS. + Please try once dxs_support=5 and if it works on other + sample rates (e.g. 44.1kHz of mp3 playback), please let us + know the PCI subsystem vendor/device id's (output of + "lspci -nv"). + If dxs_support=5 does not work, try dxs_support=4; if it + doesn't work too, try dxs_support=1. (dxs_support=1 is + usually for old motherboards. The correct implemented + board should work with 4 or 5.) If it still doesn't + work and the default setting is ok, dxs_support=3 is the + right choice. If the default setting doesn't work at all, + try dxs_support=2 to disable the DXS channels. + In any cases, please let us know the result and the + subsystem vendor/device ids. See "Links and Addresses" + below. + + Note: for the MPU401 on VIA823x, use snd-mpu401 driver + additionally. The mpu_port option is for VIA686 chips only. + + The power-management is supported. + + Module snd-via82xx-modem + ------------------------ + + Module for VIA82xx AC97 modem + + ac97_clock - AC'97 codec clock base (default 48000Hz) + + This module supports one card and autoprobe. + + Note: The default index value of this module is -2, i.e. the first + slot is excluded. + + The power-management is supported. + + Module snd-virmidi + ------------------ + + Module for virtual rawmidi devices. + This module creates virtual rawmidi devices which communicate + to the corresponding ALSA sequencer ports. + + midi_devs - MIDI devices # (1-4, default=4) + + This module supports multiple cards. + + Module snd-virtuoso + ------------------- + + Module for sound cards based on the Asus AV66/AV100/AV200 chips, + i.e., Xonar D1, DX, D2, D2X, DS, Essence ST (Deluxe), Essence STX, + HDAV1.3 (Deluxe), and HDAV1.3 Slim. + + This module supports autoprobe and multiple cards. + + Module snd-vx222 + ---------------- + + Module for Digigram VX-Pocket VX222, V222 v2 and Mic cards. + + mic - Enable Microphone on V222 Mic (NYI) + ibl - Capture IBL size. (default = 0, minimum size) + + This module supports multiple cards. + + When the driver is compiled as a module and the hotplug firmware + is supported, the firmware data is loaded via hotplug automatically. + Install the necessary firmware files in alsa-firmware package. + When no hotplug fw loader is available, you need to load the + firmware via vxloader utility in alsa-tools package. To invoke + vxloader automatically, add the following to /etc/modprobe.d/alsa.conf + + install snd-vx222 /sbin/modprobe --first-time -i snd-vx222 && /usr/bin/vxloader + + (for 2.2/2.4 kernels, add "post-install /usr/bin/vxloader" to + /etc/modules.conf, instead.) + IBL size defines the interrupts period for PCM. The smaller size + gives smaller latency but leads to more CPU consumption, too. + The size is usually aligned to 126. As default (=0), the smallest + size is chosen. The possible IBL values can be found in + /proc/asound/cardX/vx-status proc file. + + The power-management is supported. + + Module snd-vxpocket + ------------------- + + Module for Digigram VX-Pocket VX2 and 440 PCMCIA cards. + + ibl - Capture IBL size. (default = 0, minimum size) + + This module supports multiple cards. The module is compiled only when + PCMCIA is supported on kernel. + + With the older 2.6.x kernel, to activate the driver via the card + manager, you'll need to set up /etc/pcmcia/vxpocket.conf. See the + sound/pcmcia/vx/vxpocket.c. 2.6.13 or later kernel requires no + longer require a config file. + + When the driver is compiled as a module and the hotplug firmware + is supported, the firmware data is loaded via hotplug automatically. + Install the necessary firmware files in alsa-firmware package. + When no hotplug fw loader is available, you need to load the + firmware via vxloader utility in alsa-tools package. + + About capture IBL, see the description of snd-vx222 module. + + Note: snd-vxp440 driver is merged to snd-vxpocket driver since + ALSA 1.0.10. + + The power-management is supported. + + Module snd-ymfpci + ----------------- + + Module for Yamaha PCI chips (YMF72x, YMF74x & YMF75x). + + mpu_port - 0x300,0x330,0x332,0x334, 0 (disable) by default, + 1 (auto-detect for YMF744/754 only) + fm_port - 0x388,0x398,0x3a0,0x3a8, 0 (disable) by default + 1 (auto-detect for YMF744/754 only) + joystick_port - 0x201,0x202,0x204,0x205, 0 (disable) by default, + 1 (auto-detect) + rear_switch - enable shared rear/line-in switch (bool) + + This module supports autoprobe and multiple chips. + + The power-management is supported. + + Module snd-pdaudiocf + -------------------- + + Module for Sound Core PDAudioCF sound card. + + The power-management is supported. + + +AC97 Quirk Option +================= + +The ac97_quirk option is used to enable/override the workaround for +specific devices on drivers for on-board AC'97 controllers like +snd-intel8x0. Some hardware have swapped output pins between Master +and Headphone, or Surround (thanks to confusion of AC'97 +specifications from version to version :-) + +The driver provides the auto-detection of known problematic devices, +but some might be unknown or wrongly detected. In such a case, pass +the proper value with this option. + +The following strings are accepted: + - default Don't override the default setting + - none Disable the quirk + - hp_only Bind Master and Headphone controls as a single control + - swap_hp Swap headphone and master controls + - swap_surround Swap master and surround controls + - ad_sharing For AD1985, turn on OMS bit and use headphone + - alc_jack For ALC65x, turn on the jack sense mode + - inv_eapd Inverted EAPD implementation + - mute_led Bind EAPD bit for turning on/off mute LED + +For backward compatibility, the corresponding integer value -1, 0, +... are accepted, too. + +For example, if "Master" volume control has no effect on your device +but only "Headphone" does, pass ac97_quirk=hp_only module option. + + +Configuring Non-ISAPNP Cards +============================ + +When the kernel is configured with ISA-PnP support, the modules +supporting the isapnp cards will have module options "isapnp". +If this option is set, *only* the ISA-PnP devices will be probed. +For probing the non ISA-PnP cards, you have to pass "isapnp=0" option +together with the proper i/o and irq configuration. + +When the kernel is configured without ISA-PnP support, isapnp option +will be not built in. + + +Module Autoloading Support +========================== + +The ALSA drivers can be loaded automatically on demand by defining +module aliases. The string 'snd-card-%1' is requested for ALSA native +devices where %i is sound card number from zero to seven. + +To auto-load an ALSA driver for OSS services, define the string +'sound-slot-%i' where %i means the slot number for OSS, which +corresponds to the card index of ALSA. Usually, define this +as the same card module. + +An example configuration for a single emu10k1 card is like below: +----- /etc/modprobe.d/alsa.conf +alias snd-card-0 snd-emu10k1 +alias sound-slot-0 snd-emu10k1 +----- /etc/modprobe.d/alsa.conf + +The available number of auto-loaded sound cards depends on the module +option "cards_limit" of snd module. As default it's set to 1. +To enable the auto-loading of multiple cards, specify the number of +sound cards in that option. + +When multiple cards are available, it'd better to specify the index +number for each card via module option, too, so that the order of +cards is kept consistent. + +An example configuration for two sound cards is like below: + +----- /etc/modprobe.d/alsa.conf +# ALSA portion +options snd cards_limit=2 +alias snd-card-0 snd-interwave +alias snd-card-1 snd-ens1371 +options snd-interwave index=0 +options snd-ens1371 index=1 +# OSS/Free portion +alias sound-slot-0 snd-interwave +alias sound-slot-1 snd-ens1371 +----- /etc/modprobe.d/alsa.conf + +In this example, the interwave card is always loaded as the first card +(index 0) and ens1371 as the second (index 1). + +Alternative (and new) way to fixate the slot assignment is to use +"slots" option of snd module. In the case above, specify like the +following: + +options snd slots=snd-interwave,snd-ens1371 + +Then, the first slot (#0) is reserved for snd-interwave driver, and +the second (#1) for snd-ens1371. You can omit index option in each +driver if slots option is used (although you can still have them at +the same time as long as they don't conflict). + +The slots option is especially useful for avoiding the possible +hot-plugging and the resultant slot conflict. For example, in the +case above again, the first two slots are already reserved. If any +other driver (e.g. snd-usb-audio) is loaded before snd-interwave or +snd-ens1371, it will be assigned to the third or later slot. + +When a module name is given with '!', the slot will be given for any +modules but that name. For example, "slots=!snd-pcsp" will reserve +the first slot for any modules but snd-pcsp. + + +ALSA PCM devices to OSS devices mapping +======================================= + +/dev/snd/pcmC0D0[c|p] -> /dev/audio0 (/dev/audio) -> minor 4 +/dev/snd/pcmC0D0[c|p] -> /dev/dsp0 (/dev/dsp) -> minor 3 +/dev/snd/pcmC0D1[c|p] -> /dev/adsp0 (/dev/adsp) -> minor 12 +/dev/snd/pcmC1D0[c|p] -> /dev/audio1 -> minor 4+16 = 20 +/dev/snd/pcmC1D0[c|p] -> /dev/dsp1 -> minor 3+16 = 19 +/dev/snd/pcmC1D1[c|p] -> /dev/adsp1 -> minor 12+16 = 28 +/dev/snd/pcmC2D0[c|p] -> /dev/audio2 -> minor 4+32 = 36 +/dev/snd/pcmC2D0[c|p] -> /dev/dsp2 -> minor 3+32 = 39 +/dev/snd/pcmC2D1[c|p] -> /dev/adsp2 -> minor 12+32 = 44 + +The first number from /dev/snd/pcmC{X}D{Y}[c|p] expression means +sound card number and second means device number. The ALSA devices +have either 'c' or 'p' suffix indicating the direction, capture and +playback, respectively. + +Please note that the device mapping above may be varied via the module +options of snd-pcm-oss module. + + +Proc interfaces (/proc/asound) +============================== + +/proc/asound/card#/pcm#[cp]/oss +------------------------------- + String "erase" - erase all additional information about OSS applications + String "<app_name> <fragments> <fragment_size> [<options>]" + + <app_name> - name of application with (higher priority) or without path + <fragments> - number of fragments or zero if auto + <fragment_size> - size of fragment in bytes or zero if auto + <options> - optional parameters + - disable the application tries to open a pcm device for + this channel but does not want to use it. + (Cause a bug or mmap needs) + It's good for Quake etc... + - direct don't use plugins + - block force block mode (rvplayer) + - non-block force non-block mode + - whole-frag write only whole fragments (optimization affecting + playback only) + - no-silence do not fill silence ahead to avoid clicks + - buggy-ptr Returns the whitespace blocks in GETOPTR ioctl + instead of filled blocks + + Example: echo "x11amp 128 16384" > /proc/asound/card0/pcm0p/oss + echo "squake 0 0 disable" > /proc/asound/card0/pcm0c/oss + echo "rvplayer 0 0 block" > /proc/asound/card0/pcm0p/oss + + +Early Buffer Allocation +======================= + +Some drivers (e.g. hdsp) require the large contiguous buffers, and +sometimes it's too late to find such spaces when the driver module is +actually loaded due to memory fragmentation. You can pre-allocate the +PCM buffers by loading snd-page-alloc module and write commands to its +proc file in prior, for example, in the early boot stage like +/etc/init.d/*.local scripts. + +Reading the proc file /proc/drivers/snd-page-alloc shows the current +usage of page allocation. In writing, you can send the following +commands to the snd-page-alloc driver: + + - add VENDOR DEVICE MASK SIZE BUFFERS + + VENDOR and DEVICE are PCI vendor and device IDs. They take + integer numbers (0x prefix is needed for the hex). + MASK is the PCI DMA mask. Pass 0 if not restricted. + SIZE is the size of each buffer to allocate. You can pass + k and m suffix for KB and MB. The max number is 16MB. + BUFFERS is the number of buffers to allocate. It must be greater + than 0. The max number is 4. + + - erase + + This will erase the all pre-allocated buffers which are not in + use. + + +Links and Addresses +=================== + + ALSA project homepage + http://www.alsa-project.org + + Kernel Bugzilla + http://bugzilla.kernel.org/ + + ALSA Developers ML + mailto:alsa-devel@alsa-project.org + + alsa-info.sh script + http://www.alsa-project.org/alsa-info.sh |