aboutsummaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/net
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/net')
-rw-r--r--Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt29
-rw-r--r--Documentation/devicetree/bindings/net/calxeda-xgmac.txt18
-rw-r--r--Documentation/devicetree/bindings/net/can/c_can.txt49
-rw-r--r--Documentation/devicetree/bindings/net/can/cc770.txt53
-rw-r--r--Documentation/devicetree/bindings/net/can/fsl-flexcan.txt27
-rw-r--r--Documentation/devicetree/bindings/net/can/grcan.txt28
-rw-r--r--Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt53
-rw-r--r--Documentation/devicetree/bindings/net/can/sja1000.txt53
-rw-r--r--Documentation/devicetree/bindings/net/cavium-mdio.txt27
-rw-r--r--Documentation/devicetree/bindings/net/cavium-mix.txt39
-rw-r--r--Documentation/devicetree/bindings/net/cavium-pip.txt98
-rw-r--r--Documentation/devicetree/bindings/net/cdns-emac.txt23
-rw-r--r--Documentation/devicetree/bindings/net/cpsw.txt89
-rw-r--r--Documentation/devicetree/bindings/net/davinci-mdio.txt33
-rw-r--r--Documentation/devicetree/bindings/net/davinci_emac.txt41
-rw-r--r--Documentation/devicetree/bindings/net/fsl-fec.txt28
-rw-r--r--Documentation/devicetree/bindings/net/fsl-tsec-phy.txt130
-rw-r--r--Documentation/devicetree/bindings/net/lpc-eth.txt24
-rw-r--r--Documentation/devicetree/bindings/net/macb.txt25
-rw-r--r--Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt23
-rw-r--r--Documentation/devicetree/bindings/net/marvell-orion-mdio.txt35
-rw-r--r--Documentation/devicetree/bindings/net/mdio-gpio.txt26
-rw-r--r--Documentation/devicetree/bindings/net/mdio-mux-gpio.txt127
-rw-r--r--Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt75
-rw-r--r--Documentation/devicetree/bindings/net/mdio-mux.txt136
-rw-r--r--Documentation/devicetree/bindings/net/phy.txt35
-rw-r--r--Documentation/devicetree/bindings/net/smsc-lan91c111.txt10
-rw-r--r--Documentation/devicetree/bindings/net/smsc911x.txt38
-rw-r--r--Documentation/devicetree/bindings/net/stmmac.txt29
29 files changed, 1401 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt
new file mode 100644
index 00000000..7c86d5e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt
@@ -0,0 +1,29 @@
+The Broadcom BCM87XX devices are a family of 10G Ethernet PHYs. They
+have these bindings in addition to the standard PHY bindings.
+
+Compatible: Should contain "broadcom,bcm8706" or "broadcom,bcm8727" and
+ "ethernet-phy-ieee802.3-c45"
+
+Optional Properties:
+
+- broadcom,c45-reg-init : one of more sets of 4 cells. The first cell
+ is the MDIO Manageable Device (MMD) address, the second a register
+ address within the MMD, the third cell contains a mask to be ANDed
+ with the existing register value, and the fourth cell is ORed with
+ he result to yield the new register value. If the third cell has a
+ value of zero, no read of the existing value is performed.
+
+Example:
+
+ ethernet-phy@5 {
+ reg = <5>;
+ compatible = "broadcom,bcm8706", "ethernet-phy-ieee802.3-c45";
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ /*
+ * Set PMD Digital Control Register for
+ * GPIO[1] Tx/Rx
+ * GPIO[0] R64 Sync Acquired
+ */
+ broadcom,c45-reg-init = <1 0xc808 0xff8f 0x70>;
+ };
diff --git a/Documentation/devicetree/bindings/net/calxeda-xgmac.txt b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt
new file mode 100644
index 00000000..c8ae996b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt
@@ -0,0 +1,18 @@
+* Calxeda Highbank 10Gb XGMAC Ethernet
+
+Required properties:
+- compatible : Should be "calxeda,hb-xgmac"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt.
+ The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt.
+
+Optional properties:
+- dma-coherent : Present if dma operations are coherent
+
+Example:
+
+ethernet@fff50000 {
+ compatible = "calxeda,hb-xgmac";
+ reg = <0xfff50000 0x1000>;
+ interrupts = <0 77 4 0 78 4 0 79 4>;
+};
diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt
new file mode 100644
index 00000000..8f1ae812
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/c_can.txt
@@ -0,0 +1,49 @@
+Bosch C_CAN/D_CAN controller Device Tree Bindings
+-------------------------------------------------
+
+Required properties:
+- compatible : Should be "bosch,c_can" for C_CAN controllers and
+ "bosch,d_can" for D_CAN controllers.
+- reg : physical base address and size of the C_CAN/D_CAN
+ registers map
+- interrupts : property with a value describing the interrupt
+ number
+
+Optional properties:
+- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the
+ instance number
+
+Note: "ti,hwmods" field is used to fetch the base address and irq
+resources from TI, omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Example:
+
+Step1: SoC common .dtsi file
+
+ dcan1: d_can@481d0000 {
+ compatible = "bosch,d_can";
+ reg = <0x481d0000 0x2000>;
+ interrupts = <55>;
+ interrupt-parent = <&intc>;
+ status = "disabled";
+ };
+
+(or)
+
+ dcan1: d_can@481d0000 {
+ compatible = "bosch,d_can";
+ ti,hwmods = "d_can1";
+ reg = <0x481d0000 0x2000>;
+ interrupts = <55>;
+ interrupt-parent = <&intc>;
+ status = "disabled";
+ };
+
+Step 2: board specific .dts file
+
+ &dcan1 {
+ status = "okay";
+ };
diff --git a/Documentation/devicetree/bindings/net/can/cc770.txt b/Documentation/devicetree/bindings/net/can/cc770.txt
new file mode 100644
index 00000000..77027bf6
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/cc770.txt
@@ -0,0 +1,53 @@
+Memory mapped Bosch CC770 and Intel AN82527 CAN controller
+
+Note: The CC770 is a CAN controller from Bosch, which is 100%
+compatible with the old AN82527 from Intel, but with "bugs" being fixed.
+
+Required properties:
+
+- compatible : should be "bosch,cc770" for the CC770 and "intc,82527"
+ for the AN82527.
+
+- reg : should specify the chip select, address offset and size required
+ to map the registers of the controller. The size is usually 0x80.
+
+- interrupts : property with a value describing the interrupt source
+ (number and sensitivity) required for the controller.
+
+Optional properties:
+
+- bosch,external-clock-frequency : frequency of the external oscillator
+ clock in Hz. Note that the internal clock frequency used by the
+ controller is half of that value. If not specified, a default
+ value of 16000000 (16 MHz) is used.
+
+- bosch,clock-out-frequency : slock frequency in Hz on the CLKOUT pin.
+ If not specified or if the specified value is 0, the CLKOUT pin
+ will be disabled.
+
+- bosch,slew-rate : slew rate of the CLKOUT signal. If not specified,
+ a resonable value will be calculated.
+
+- bosch,disconnect-rx0-input : see data sheet.
+
+- bosch,disconnect-rx1-input : see data sheet.
+
+- bosch,disconnect-tx1-output : see data sheet.
+
+- bosch,polarity-dominant : see data sheet.
+
+- bosch,divide-memory-clock : see data sheet.
+
+- bosch,iso-low-speed-mux : see data sheet.
+
+For further information, please have a look to the CC770 or AN82527.
+
+Examples:
+
+can@3,100 {
+ compatible = "bosch,cc770";
+ reg = <3 0x100 0x80>;
+ interrupts = <2 0>;
+ interrupt-parent = <&mpic>;
+ bosch,external-clock-frequency = <16000000>;
+};
diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
new file mode 100644
index 00000000..8ff324ea
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
@@ -0,0 +1,27 @@
+Flexcan CAN controller on Freescale's ARM and PowerPC system-on-a-chip (SOC).
+
+Required properties:
+
+- compatible : Should be "fsl,<processor>-flexcan"
+
+ An implementation should also claim any of the following compatibles
+ that it is fully backwards compatible with:
+
+ - fsl,p1010-flexcan
+
+- reg : Offset and length of the register set for this device
+- interrupts : Interrupt tuple for this device
+
+Optional properties:
+
+- clock-frequency : The oscillator frequency driving the flexcan device
+
+Example:
+
+ can@1c000 {
+ compatible = "fsl,p1010-flexcan";
+ reg = <0x1c000 0x1000>;
+ interrupts = <48 0x2>;
+ interrupt-parent = <&mpic>;
+ clock-frequency = <200000000>; // filled in by bootloader
+ };
diff --git a/Documentation/devicetree/bindings/net/can/grcan.txt b/Documentation/devicetree/bindings/net/can/grcan.txt
new file mode 100644
index 00000000..34ef3498
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/grcan.txt
@@ -0,0 +1,28 @@
+Aeroflex Gaisler GRCAN and GRHCAN CAN controllers.
+
+The GRCAN and CRHCAN CAN controllers are available in the GRLIB VHDL IP core
+library.
+
+Note: These properties are built from the AMBA plug&play in a Leon SPARC system
+(the ordinary environment for GRCAN and GRHCAN). There are no dts files for
+sparc.
+
+Required properties:
+
+- name : Should be "GAISLER_GRCAN", "01_03d", "GAISLER_GRHCAN" or "01_034"
+
+- reg : Address and length of the register set for the device
+
+- freq : Frequency of the external oscillator clock in Hz (the frequency of
+ the amba bus in the ordinary case)
+
+- interrupts : Interrupt number for this device
+
+Optional properties:
+
+- systemid : If not present or if the value of the least significant 16 bits
+ of this 32-bit property is smaller than GRCAN_TXBUG_SAFE_GRLIB_VERSION
+ a bug workaround is activated.
+
+For further information look in the documentation for the GLIB IP core library:
+http://www.gaisler.com/products/grlib/grip.pdf
diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt
new file mode 100644
index 00000000..2fa4fcd3
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt
@@ -0,0 +1,53 @@
+CAN Device Tree Bindings
+------------------------
+
+(c) 2006-2009 Secret Lab Technologies Ltd
+Grant Likely <grant.likely@secretlab.ca>
+
+fsl,mpc5200-mscan nodes
+-----------------------
+In addition to the required compatible-, reg- and interrupt-properties, you can
+also specify which clock source shall be used for the controller:
+
+- fsl,mscan-clock-source : a string describing the clock source. Valid values
+ are: "ip" for ip bus clock
+ "ref" for reference clock (XTAL)
+ "ref" is default in case this property is not
+ present.
+
+fsl,mpc5121-mscan nodes
+-----------------------
+In addition to the required compatible-, reg- and interrupt-properties, you can
+also specify which clock source and divider shall be used for the controller:
+
+- fsl,mscan-clock-source : a string describing the clock source. Valid values
+ are: "ip" for ip bus clock
+ "ref" for reference clock
+ "sys" for system clock
+ If this property is not present, an optimal CAN
+ clock source and frequency based on the system
+ clock will be selected. If this is not possible,
+ the reference clock will be used.
+
+- fsl,mscan-clock-divider: for the reference and system clock, an additional
+ clock divider can be specified. By default, a
+ value of 1 is used.
+
+Note that the MPC5121 Rev. 1 processor is not supported.
+
+Examples:
+ can@1300 {
+ compatible = "fsl,mpc5121-mscan";
+ interrupts = <12 0x8>;
+ interrupt-parent = <&ipic>;
+ reg = <0x1300 0x80>;
+ };
+
+ can@1380 {
+ compatible = "fsl,mpc5121-mscan";
+ interrupts = <13 0x8>;
+ interrupt-parent = <&ipic>;
+ reg = <0x1380 0x80>;
+ fsl,mscan-clock-source = "ref";
+ fsl,mscan-clock-divider = <3>;
+ };
diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt
new file mode 100644
index 00000000..c2dbcec0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/sja1000.txt
@@ -0,0 +1,53 @@
+Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
+
+Required properties:
+
+- compatible : should be "nxp,sja1000".
+
+- reg : should specify the chip select, address offset and size required
+ to map the registers of the SJA1000. The size is usually 0x80.
+
+- interrupts: property with a value describing the interrupt source
+ (number and sensitivity) required for the SJA1000.
+
+Optional properties:
+
+- nxp,external-clock-frequency : Frequency of the external oscillator
+ clock in Hz. Note that the internal clock frequency used by the
+ SJA1000 is half of that value. If not specified, a default value
+ of 16000000 (16 MHz) is used.
+
+- nxp,tx-output-mode : operation mode of the TX output control logic:
+ <0x0> : bi-phase output mode
+ <0x1> : normal output mode (default)
+ <0x2> : test output mode
+ <0x3> : clock output mode
+
+- nxp,tx-output-config : TX output pin configuration:
+ <0x01> : TX0 invert
+ <0x02> : TX0 pull-down (default)
+ <0x04> : TX0 pull-up
+ <0x06> : TX0 push-pull
+ <0x08> : TX1 invert
+ <0x10> : TX1 pull-down
+ <0x20> : TX1 pull-up
+ <0x30> : TX1 push-pull
+
+- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin.
+ If not specified or if the specified value is 0, the CLKOUT pin
+ will be disabled.
+
+- nxp,no-comparator-bypass : Allows to disable the CAN input comperator.
+
+For further information, please have a look to the SJA1000 data sheet.
+
+Examples:
+
+can@3,100 {
+ compatible = "nxp,sja1000";
+ reg = <3 0x100 0x80>;
+ interrupts = <2 0>;
+ interrupt-parent = <&mpic>;
+ nxp,external-clock-frequency = <16000000>;
+};
+
diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt
new file mode 100644
index 00000000..04cb7491
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt
@@ -0,0 +1,27 @@
+* System Management Interface (SMI) / MDIO
+
+Properties:
+- compatible: "cavium,octeon-3860-mdio"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the MDIO bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>. MDIO addresses have no size component.
+
+Typically an MDIO bus might have several children.
+
+Example:
+ mdio@1180000001800 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00001800 0x0 0x40>;
+
+ ethernet-phy@0 {
+ ...
+ reg = <0>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt
new file mode 100644
index 00000000..5da628db
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-mix.txt
@@ -0,0 +1,39 @@
+* MIX Ethernet controller.
+
+Properties:
+- compatible: "cavium,octeon-5750-mix"
+
+ Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX
+ devices.
+
+- reg: The base addresses of four separate register banks. The first
+ bank contains the MIX registers. The second bank the corresponding
+ AGL registers. The third bank are the AGL registers shared by all
+ MIX devices present. The fourth bank is the AGL_PRT_CTL shared by
+ all MIX devices present.
+
+- cell-index: A single cell specifying which portion of the shared
+ register banks corresponds to this MIX device.
+
+- interrupts: Two interrupt specifiers. The first is the MIX
+ interrupt routing and the second the routing for the AGL interrupts.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+ if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+ ethernet@1070000100800 {
+ compatible = "cavium,octeon-5750-mix";
+ reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+ <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+ <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */
+ <0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */
+ cell-index = <1>;
+ interrupts = <1 18>, < 1 46>;
+ local-mac-address = [ 00 0f b7 10 63 54 ];
+ phy-handle = <&phy1>;
+ };
diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt
new file mode 100644
index 00000000..d4c53ba0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-pip.txt
@@ -0,0 +1,98 @@
+* PIP Ethernet nexus.
+
+The PIP Ethernet nexus can control several data packet input/output
+devices. The devices have a two level grouping scheme. There may be
+several interfaces, and each interface may have several ports. These
+ports might be an individual Ethernet PHY.
+
+
+Properties for the PIP nexus:
+- compatible: "cavium,octeon-3860-pip"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the PIP's register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP interfaces which is a child the PIP nexus:
+- compatible: "cavium,octeon-3860-pip-interface"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The interface number.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP port which is a child the PIP interface:
+- compatible: "cavium,octeon-3860-pip-port"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The port number within the interface group.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+ if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+
+ pip@11800a0000000 {
+ compatible = "cavium,octeon-3860-pip";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+ interface@0 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 60 ];
+ phy-handle = <&phy2>;
+ };
+ ethernet@1 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x1>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 61 ];
+ phy-handle = <&phy3>;
+ };
+ ethernet@2 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x2>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 62 ];
+ phy-handle = <&phy4>;
+ };
+ ethernet@3 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x3>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 63 ];
+ phy-handle = <&phy5>;
+ };
+ };
+
+ interface@1 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 64 ];
+ phy-handle = <&phy6>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt
new file mode 100644
index 00000000..09055c24
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cdns-emac.txt
@@ -0,0 +1,23 @@
+* Cadence EMAC Ethernet controller
+
+Required properties:
+- compatible: Should be "cdns,[<chip>-]{emac}"
+ Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
+ or the generic form: "cdns,emac".
+- reg: Address and length of the register set for the device
+- interrupts: Should contain macb interrupt
+- phy-mode: String, operation mode of the PHY interface.
+ Supported values are: "mii", "rmii".
+
+Optional properties:
+- local-mac-address: 6 bytes, mac address
+
+Examples:
+
+ macb0: ethernet@fffc4000 {
+ compatible = "cdns,at91rm9200-emac";
+ reg = <0xfffc4000 0x4000>;
+ interrupts = <21>;
+ phy-mode = "rmii";
+ local-mac-address = [3a 0e 03 04 05 06];
+ };
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
new file mode 100644
index 00000000..ecfdf756
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -0,0 +1,89 @@
+TI SoC Ethernet Switch Controller Device Tree Bindings
+------------------------------------------------------
+
+Required properties:
+- compatible : Should be "ti,cpsw"
+- reg : physical base address and size of the cpsw
+ registers map
+- interrupts : property with a value describing the interrupt
+ number
+- interrupt-parent : The parent interrupt controller
+- cpdma_channels : Specifies number of channels in CPDMA
+- ale_entries : Specifies No of entries ALE can hold
+- bd_ram_size : Specifies internal descriptor RAM size
+- rx_descs : Specifies number of Rx descriptors
+- mac_control : Specifies Default MAC control register content
+ for the specific platform
+- slaves : Specifies number for slaves
+- cpts_active_slave : Specifies the slave to use for time stamping
+- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds
+- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds
+- phy_id : Specifies slave phy id
+- mac-address : Specifies slave MAC address
+
+Optional properties:
+- ti,hwmods : Must be "cpgmac0"
+- no_bd_ram : Must be 0 or 1
+- dual_emac : Specifies Switch to act as Dual EMAC
+- dual_emac_res_vlan : Specifies VID to be used to segregate the ports
+
+Note: "ti,hwmods" field is used to fetch the base address and irq
+resources from TI, omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Examples:
+
+ mac: ethernet@4A100000 {
+ compatible = "ti,cpsw";
+ reg = <0x4A100000 0x1000>;
+ interrupts = <55 0x4>;
+ interrupt-parent = <&intc>;
+ cpdma_channels = <8>;
+ ale_entries = <1024>;
+ bd_ram_size = <0x2000>;
+ no_bd_ram = <0>;
+ rx_descs = <64>;
+ mac_control = <0x20>;
+ slaves = <2>;
+ cpts_active_slave = <0>;
+ cpts_clock_mult = <0x80000000>;
+ cpts_clock_shift = <29>;
+ cpsw_emac0: slave@0 {
+ phy_id = <&davinci_mdio>, <0>;
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+ cpsw_emac1: slave@1 {
+ phy_id = <&davinci_mdio>, <1>;
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+ };
+
+(or)
+ mac: ethernet@4A100000 {
+ compatible = "ti,cpsw";
+ ti,hwmods = "cpgmac0";
+ cpdma_channels = <8>;
+ ale_entries = <1024>;
+ bd_ram_size = <0x2000>;
+ no_bd_ram = <0>;
+ rx_descs = <64>;
+ mac_control = <0x20>;
+ slaves = <2>;
+ cpts_active_slave = <0>;
+ cpts_clock_mult = <0x80000000>;
+ cpts_clock_shift = <29>;
+ cpsw_emac0: slave@0 {
+ phy_id = <&davinci_mdio>, <0>;
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+ cpsw_emac1: slave@1 {
+ phy_id = <&davinci_mdio>, <1>;
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
new file mode 100644
index 00000000..72efaaf7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
@@ -0,0 +1,33 @@
+TI SoC Davinci MDIO Controller Device Tree Bindings
+---------------------------------------------------
+
+Required properties:
+- compatible : Should be "ti,davinci_mdio"
+- reg : physical base address and size of the davinci mdio
+ registers map
+- bus_freq : Mdio Bus frequency
+
+Optional properties:
+- ti,hwmods : Must be "davinci_mdio"
+
+Note: "ti,hwmods" field is used to fetch the base address and irq
+resources from TI, omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Examples:
+
+ mdio: davinci_mdio@4A101000 {
+ compatible = "ti,cpsw";
+ reg = <0x4A101000 0x1000>;
+ bus_freq = <1000000>;
+ };
+
+(or)
+
+ mdio: davinci_mdio@4A101000 {
+ compatible = "ti,cpsw";
+ ti,hwmods = "davinci_mdio";
+ bus_freq = <1000000>;
+ };
diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt
new file mode 100644
index 00000000..48b259e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/davinci_emac.txt
@@ -0,0 +1,41 @@
+* Texas Instruments Davinci EMAC
+
+This file provides information, what the device node
+for the davinci_emac interface contains.
+
+Required properties:
+- compatible: "ti,davinci-dm6467-emac";
+- reg: Offset and length of the register set for the device
+- ti,davinci-ctrl-reg-offset: offset to control register
+- ti,davinci-ctrl-mod-reg-offset: offset to control module register
+- ti,davinci-ctrl-ram-offset: offset to control module ram
+- ti,davinci-ctrl-ram-size: size of control module ram
+- ti,davinci-rmii-en: use RMII
+- ti,davinci-no-bd-ram: has the emac controller BD RAM
+- phy-handle: Contains a phandle to an Ethernet PHY.
+ if not, davinci_emac driver defaults to 100/FULL
+- interrupts: interrupt mapping for the davinci emac interrupts sources:
+ 4 sources: <Receive Threshold Interrupt
+ Receive Interrupt
+ Transmit Interrupt
+ Miscellaneous Interrupt>
+
+Optional properties:
+- local-mac-address : 6 bytes, mac address
+
+Example (enbw_cmc board):
+ eth0: emac@1e20000 {
+ compatible = "ti,davinci-dm6467-emac";
+ reg = <0x220000 0x4000>;
+ ti,davinci-ctrl-reg-offset = <0x3000>;
+ ti,davinci-ctrl-mod-reg-offset = <0x2000>;
+ ti,davinci-ctrl-ram-offset = <0>;
+ ti,davinci-ctrl-ram-size = <0x2000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <33
+ 34
+ 35
+ 36
+ >;
+ interrupt-parent = <&intc>;
+ };
diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt
new file mode 100644
index 00000000..d5363922
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/fsl-fec.txt
@@ -0,0 +1,28 @@
+* Freescale Fast Ethernet Controller (FEC)
+
+Required properties:
+- compatible : Should be "fsl,<soc>-fec"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain fec interrupt
+- phy-mode : String, operation mode of the PHY interface.
+ Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii",
+ "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii".
+
+Optional properties:
+- local-mac-address : 6 bytes, mac address
+- phy-reset-gpios : Should specify the gpio for phy reset
+- phy-reset-duration : Reset duration in milliseconds. Should present
+ only if property "phy-reset-gpios" is available. Missing the property
+ will have the duration be 1 millisecond. Numbers greater than 1000 are
+ invalid and 1 millisecond will be used instead.
+
+Example:
+
+ethernet@83fec000 {
+ compatible = "fsl,imx51-fec", "fsl,imx27-fec";
+ reg = <0x83fec000 0x4000>;
+ interrupts = <87>;
+ phy-mode = "mii";
+ phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
+ local-mac-address = [00 04 9F 01 1B B9];
+};
diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
new file mode 100644
index 00000000..2c6be037
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
@@ -0,0 +1,130 @@
+* MDIO IO device
+
+The MDIO is a bus to which the PHY devices are connected. For each
+device that exists on this bus, a child node should be created. See
+the definition of the PHY node in booting-without-of.txt for an example
+of how to define a PHY.
+
+Required properties:
+ - reg : Offset and length of the register set for the device
+ - compatible : Should define the compatible device type for the
+ mdio. Currently, this is most likely to be "fsl,gianfar-mdio"
+
+Example:
+
+ mdio@24520 {
+ reg = <24520 20>;
+ compatible = "fsl,gianfar-mdio";
+
+ ethernet-phy@0 {
+ ......
+ };
+ };
+
+* TBI Internal MDIO bus
+
+As of this writing, every tsec is associated with an internal TBI PHY.
+This PHY is accessed through the local MDIO bus. These buses are defined
+similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi".
+The TBI PHYs underneath them are similar to normal PHYs, but the reg property
+is considered instructive, rather than descriptive. The reg property should
+be chosen so it doesn't interfere with other PHYs on the bus.
+
+* Gianfar-compatible ethernet nodes
+
+Properties:
+
+ - device_type : Should be "network"
+ - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
+ - compatible : Should be "gianfar"
+ - reg : Offset and length of the register set for the device
+ - local-mac-address : List of bytes representing the ethernet address of
+ this controller
+ - interrupts : For FEC devices, the first interrupt is the device's
+ interrupt. For TSEC and eTSEC devices, the first interrupt is
+ transmit, the second is receive, and the third is error.
+ - phy-handle : The phandle for the PHY connected to this ethernet
+ controller.
+ - fixed-link : <a b c d e> where a is emulated phy id - choose any,
+ but unique to the all specified fixed-links, b is duplex - 0 half,
+ 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
+ pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
+ - phy-connection-type : a string naming the controller/PHY interface type,
+ i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
+ "tbi", or "rtbi". This property is only really needed if the connection
+ is of type "rgmii-id", as all other connection types are detected by
+ hardware.
+ - fsl,magic-packet : If present, indicates that the hardware supports
+ waking up via magic packet.
+ - bd-stash : If present, indicates that the hardware supports stashing
+ buffer descriptors in the L2.
+ - rx-stash-len : Denotes the number of bytes of a received buffer to stash
+ in the L2.
+ - rx-stash-idx : Denotes the index of the first byte from the received
+ buffer to stash in the L2.
+
+Example:
+ ethernet@24000 {
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 E0 0C 00 73 00 ];
+ interrupts = <29 2 30 2 34 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy0>
+ };
+
+* Gianfar PTP clock nodes
+
+General Properties:
+
+ - compatible Should be "fsl,etsec-ptp"
+ - reg Offset and length of the register set for the device
+ - interrupts There should be at least two interrupts. Some devices
+ have as many as four PTP related interrupts.
+
+Clock Properties:
+
+ - fsl,tclk-period Timer reference clock period in nanoseconds.
+ - fsl,tmr-prsc Prescaler, divides the output clock.
+ - fsl,tmr-add Frequency compensation value.
+ - fsl,tmr-fiper1 Fixed interval period pulse generator.
+ - fsl,tmr-fiper2 Fixed interval period pulse generator.
+ - fsl,max-adj Maximum frequency adjustment in parts per billion.
+
+ These properties set the operational parameters for the PTP
+ clock. You must choose these carefully for the clock to work right.
+ Here is how to figure good values:
+
+ TimerOsc = system clock MHz
+ tclk_period = desired clock period nanoseconds
+ NominalFreq = 1000 / tclk_period MHz
+ FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0)
+ tmr_add = ceil(2^32 / FreqDivRatio)
+ OutputClock = NominalFreq / tmr_prsc MHz
+ PulseWidth = 1 / OutputClock microseconds
+ FiperFreq1 = desired frequency in Hz
+ FiperDiv1 = 1000000 * OutputClock / FiperFreq1
+ tmr_fiper1 = tmr_prsc * tclk_period * FiperDiv1 - tclk_period
+ max_adj = 1000000000 * (FreqDivRatio - 1.0) - 1
+
+ The calculation for tmr_fiper2 is the same as for tmr_fiper1. The
+ driver expects that tmr_fiper1 will be correctly set to produce a 1
+ Pulse Per Second (PPS) signal, since this will be offered to the PPS
+ subsystem to synchronize the Linux clock.
+
+Example:
+
+ ptp_clock@24E00 {
+ compatible = "fsl,etsec-ptp";
+ reg = <0x24E00 0xB0>;
+ interrupts = <12 0x8 13 0x8>;
+ interrupt-parent = < &ipic >;
+ fsl,tclk-period = <10>;
+ fsl,tmr-prsc = <100>;
+ fsl,tmr-add = <0x999999A4>;
+ fsl,tmr-fiper1 = <0x3B9AC9F6>;
+ fsl,tmr-fiper2 = <0x00018696>;
+ fsl,max-adj = <659999998>;
+ };
diff --git a/Documentation/devicetree/bindings/net/lpc-eth.txt b/Documentation/devicetree/bindings/net/lpc-eth.txt
new file mode 100644
index 00000000..585021ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/lpc-eth.txt
@@ -0,0 +1,24 @@
+* NXP LPC32xx SoC Ethernet Controller
+
+Required properties:
+- compatible: Should be "nxp,lpc-eth"
+- reg: Address and length of the register set for the device
+- interrupts: Should contain ethernet controller interrupt
+
+Optional properties:
+- phy-mode: String, operation mode of the PHY interface.
+ Supported values are: "mii", "rmii" (default)
+- use-iram: Use LPC32xx internal SRAM (IRAM) for DMA buffering
+- local-mac-address : 6 bytes, mac address
+
+Example:
+
+ mac: ethernet@31060000 {
+ compatible = "nxp,lpc-eth";
+ reg = <0x31060000 0x1000>;
+ interrupt-parent = <&mic>;
+ interrupts = <29 0>;
+
+ phy-mode = "rmii";
+ use-iram;
+ };
diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt
new file mode 100644
index 00000000..44afa0e5
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/macb.txt
@@ -0,0 +1,25 @@
+* Cadence MACB/GEM Ethernet controller
+
+Required properties:
+- compatible: Should be "cdns,[<chip>-]{macb|gem}"
+ Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
+ Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
+ Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on
+ the Cadence GEM, or the generic form: "cdns,gem".
+- reg: Address and length of the register set for the device
+- interrupts: Should contain macb interrupt
+- phy-mode: String, operation mode of the PHY interface.
+ Supported values are: "mii", "rmii", "gmii", "rgmii".
+
+Optional properties:
+- local-mac-address: 6 bytes, mac address
+
+Examples:
+
+ macb0: ethernet@fffc4000 {
+ compatible = "cdns,at32ap7000-macb";
+ reg = <0xfffc4000 0x4000>;
+ interrupts = <21>;
+ phy-mode = "rmii";
+ local-mac-address = [3a 0e 03 04 05 06];
+ };
diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
new file mode 100644
index 00000000..859a6fa7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
@@ -0,0 +1,23 @@
+* Marvell Armada 370 / Armada XP Ethernet Controller (NETA)
+
+Required properties:
+- compatible: should be "marvell,armada-370-neta".
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device
+- phy: A phandle to a phy node defining the PHY address (as the reg
+ property, a single integer).
+- phy-mode: The interface between the SoC and the PHY (a string that
+ of_get_phy_mode() can understand)
+- clocks: a pointer to the reference clock for this device.
+
+Example:
+
+ethernet@d0070000 {
+ compatible = "marvell,armada-370-neta";
+ reg = <0xd0070000 0x2500>;
+ interrupts = <8>;
+ clocks = <&gate_clk 4>;
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt
new file mode 100644
index 00000000..34e7aafa
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt
@@ -0,0 +1,35 @@
+* Marvell MDIO Ethernet Controller interface
+
+The Ethernet controllers of the Marvel Kirkwood, Dove, Orion5x,
+MV78xx0, Armada 370 and Armada XP have an identical unit that provides
+an interface with the MDIO bus. This driver handles this MDIO
+interface.
+
+Required properties:
+- compatible: "marvell,orion-mdio"
+- reg: address and length of the SMI register
+
+The child nodes of the MDIO driver are the individual PHY devices
+connected to this MDIO bus. They must have a "reg" property given the
+PHY address on the MDIO bus.
+
+Example at the SoC level:
+
+mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0xd0072004 0x4>;
+};
+
+And at the board level:
+
+mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+}
diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt
new file mode 100644
index 00000000..c79bab02
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt
@@ -0,0 +1,26 @@
+MDIO on GPIOs
+
+Currently defined compatibles:
+- virtual,gpio-mdio
+
+MDC and MDIO lines connected to GPIO controllers are listed in the
+gpios property as described in section VIII.1 in the following order:
+
+MDC, MDIO.
+
+Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases"
+node.
+
+Example:
+
+aliases {
+ mdio-gpio0 = <&mdio0>;
+};
+
+mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qe_pio_a 11
+ &qe_pio_c 6>;
+};
diff --git a/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt
new file mode 100644
index 00000000..79384113
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt
@@ -0,0 +1,127 @@
+Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
+
+This is a special case of a MDIO bus multiplexer. One or more GPIO
+lines are used to control which child bus is connected.
+
+Required properties in addition to the generic multiplexer properties:
+
+- compatible : mdio-mux-gpio.
+- gpios : GPIO specifiers for each GPIO line. One or more must be specified.
+
+
+Example :
+
+ /* The parent MDIO bus. */
+ smi1: mdio@1180000001900 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00001900 0x0 0x40>;
+ };
+
+ /*
+ An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
+ pair of GPIO lines. Child busses 2 and 3 populated with 4
+ PHYs each.
+ */
+ mdio-mux {
+ compatible = "mdio-mux-gpio";
+ gpios = <&gpio1 3 0>, <&gpio1 4 0>;
+ mdio-parent-bus = <&smi1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy11: ethernet-phy@1 {
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ phy12: ethernet-phy@2 {
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ phy13: ethernet-phy@3 {
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ phy14: ethernet-phy@4 {
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ };
+
+ mdio@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy21: ethernet-phy@1 {
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy22: ethernet-phy@2 {
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy23: ethernet-phy@3 {
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy24: ethernet-phy@4 {
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
new file mode 100644
index 00000000..8516929c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
@@ -0,0 +1,75 @@
+Properties for an MDIO bus multiplexer controlled by a memory-mapped device
+
+This is a special case of a MDIO bus multiplexer. A memory-mapped device,
+like an FPGA, is used to control which child bus is connected. The mdio-mux
+node must be a child of the memory-mapped device. The driver currently only
+supports devices with eight-bit registers.
+
+Required properties in addition to the generic multiplexer properties:
+
+- compatible : string, must contain "mdio-mux-mmioreg"
+
+- reg : integer, contains the offset of the register that controls the bus
+ multiplexer. The size field in the 'reg' property is the size of
+ register, and must therefore be 1.
+
+- mux-mask : integer, contains an eight-bit mask that specifies which
+ bits in the register control the actual bus multiplexer. The
+ 'reg' property of each child mdio-mux node must be constrained by
+ this mask.
+
+Example:
+
+The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes.
+For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus.
+A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on
+BRDCFG1 that control the actual mux.
+
+ /* The FPGA node */
+ fpga: board-control@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis";
+ reg = <3 0 0x30>;
+ ranges = <0 3 0 0x30>;
+
+ mdio-mux-emi2 {
+ compatible = "mdio-mux-mmioreg", "mdio-mux";
+ mdio-parent-bus = <&xmdio0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <9 1>; // BRDCFG1
+ mux-mask = <0x6>; // EMI2
+
+ emi2_slot1: mdio@0 { // Slot 1 XAUI (FM2)
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy_xgmii_slot1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <4>;
+ };
+ };
+
+ emi2_slot2: mdio@2 { // Slot 2 XAUI (FM1)
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy_xgmii_slot2: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0>;
+ };
+ };
+ };
+ };
+
+ /* The parent MDIO bus. */
+ xmdio0: mdio@f1000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,fman-xmdio";
+ reg = <0xf1000 0x1000>;
+ interrupts = <100 1 0 0>;
+ };
diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt
new file mode 100644
index 00000000..f65606f8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio-mux.txt
@@ -0,0 +1,136 @@
+Common MDIO bus multiplexer/switch properties.
+
+An MDIO bus multiplexer/switch will have several child busses that are
+numbered uniquely in a device dependent manner. The nodes for an MDIO
+bus multiplexer/switch will have one child node for each child bus.
+
+Required properties:
+- mdio-parent-bus : phandle to the parent MDIO bus.
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- Other properties specific to the multiplexer/switch hardware.
+
+Required properties for child nodes:
+- #address-cells = <1>;
+- #size-cells = <0>;
+- reg : The sub-bus number.
+
+
+Example :
+
+ /* The parent MDIO bus. */
+ smi1: mdio@1180000001900 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00001900 0x0 0x40>;
+ };
+
+ /*
+ An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
+ pair of GPIO lines. Child busses 2 and 3 populated with 4
+ PHYs each.
+ */
+ mdio-mux {
+ compatible = "mdio-mux-gpio";
+ gpios = <&gpio1 3 0>, <&gpio1 4 0>;
+ mdio-parent-bus = <&smi1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy11: ethernet-phy@1 {
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ phy12: ethernet-phy@2 {
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ phy13: ethernet-phy@3 {
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ phy14: ethernet-phy@4 {
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ };
+
+ mdio@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy21: ethernet-phy@1 {
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy22: ethernet-phy@2 {
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy23: ethernet-phy@3 {
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy24: ethernet-phy@4 {
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
new file mode 100644
index 00000000..7cd18fbf
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -0,0 +1,35 @@
+PHY nodes
+
+Required properties:
+
+ - device_type : Should be "ethernet-phy"
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - reg : The ID number for the phy, usually a small integer
+ - linux,phandle : phandle for this node; likely referenced by an
+ ethernet controller node.
+
+Optional Properties:
+
+- compatible: Compatible list, may contain
+ "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for
+ PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45
+ specifications. If neither of these are specified, the default is to
+ assume clause 22. The compatible list may also contain other
+ elements.
+
+Example:
+
+ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ linux,phandle = <2452000>;
+ interrupt-parent = <40000>;
+ interrupts = <35 1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+};
diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt
new file mode 100644
index 00000000..953049b4
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt
@@ -0,0 +1,10 @@
+SMSC LAN91c111 Ethernet mac
+
+Required properties:
+- compatible = "smsc,lan91c111";
+- reg : physical address and size of registers
+- interrupts : interrupt connection
+
+Optional properties:
+- phy-device : phandle to Ethernet phy
+- local-mac-address : Ethernet mac address to use
diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt
new file mode 100644
index 00000000..adb5b574
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/smsc911x.txt
@@ -0,0 +1,38 @@
+* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller
+
+Required properties:
+- compatible : Should be "smsc,lan<model>", "smsc,lan9115"
+- reg : Address and length of the io space for SMSC LAN
+- interrupts : Should contain SMSC LAN interrupt line
+- interrupt-parent : Should be the phandle for the interrupt controller
+ that services interrupts for this device
+- phy-mode : String, operation mode of the PHY interface.
+ Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii",
+ "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii".
+
+Optional properties:
+- reg-shift : Specify the quantity to shift the register offsets by
+- reg-io-width : Specify the size (in bytes) of the IO accesses that
+ should be performed on the device. Valid value for SMSC LAN is
+ 2 or 4. If it's omitted or invalid, the size would be 2.
+- smsc,irq-active-high : Indicates the IRQ polarity is active-high
+- smsc,irq-push-pull : Indicates the IRQ type is push-pull
+- smsc,force-internal-phy : Forces SMSC LAN controller to use
+ internal PHY
+- smsc,force-external-phy : Forces SMSC LAN controller to use
+ external PHY
+- smsc,save-mac-address : Indicates that mac address needs to be saved
+ before resetting the controller
+- local-mac-address : 6 bytes, mac address
+
+Examples:
+
+lan9220@f4000000 {
+ compatible = "smsc,lan9220", "smsc,lan9115";
+ reg = <0xf4000000 0x2000000>;
+ phy-mode = "mii";
+ interrupt-parent = <&gpio1>;
+ interrupts = <31>;
+ reg-io-width = <4>;
+ smsc,irq-push-pull;
+};
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
new file mode 100644
index 00000000..060bbf09
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -0,0 +1,29 @@
+* STMicroelectronics 10/100/1000 Ethernet driver (GMAC)
+
+Required properties:
+- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac"
+ For backwards compatibility: "st,spear600-gmac" is also supported.
+- reg: Address and length of the register set for the device
+- interrupt-parent: Should be the phandle for the interrupt controller
+ that services interrupts for this device
+- interrupts: Should contain the STMMAC interrupts
+- interrupt-names: Should contain the interrupt names "macirq"
+ "eth_wake_irq" if this interrupt is supported in the "interrupts"
+ property
+- phy-mode: String, operation mode of the PHY interface.
+ Supported values are: "mii", "rmii", "gmii", "rgmii".
+
+Optional properties:
+- mac-address: 6 bytes, mac address
+
+Examples:
+
+ gmac0: ethernet@e0800000 {
+ compatible = "st,spear600-gmac";
+ reg = <0xe0800000 0x8000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <24 23>;
+ interrupt-names = "macirq", "eth_wake_irq";
+ mac-address = [000000000000]; /* Filled in by U-Boot */
+ phy-mode = "gmii";
+ };