diff options
| author | Fathi Boudra <fathi.boudra@linaro.org> | 2013-04-28 09:33:08 +0300 |
|---|---|---|
| committer | Fathi Boudra <fathi.boudra@linaro.org> | 2013-04-28 09:33:08 +0300 |
| commit | 3b4bd47f8f4ed3aaf7c81c9b5d2d37ad79fadf4a (patch) | |
| tree | b9996006addfd7ae70a39672b76843b49aebc189 /Documentation/devicetree/bindings/powerpc | |
Imported Upstream version 3.9.0HEADupstream/3.9.0upstreammaster
Diffstat (limited to 'Documentation/devicetree/bindings/powerpc')
45 files changed, 3575 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt b/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt new file mode 100644 index 00000000..ee459806 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt @@ -0,0 +1,52 @@ +PPC4xx Clock Power Management (CPM) node + +Required properties: + - compatible : compatible list, currently only "ibm,cpm" + - dcr-access-method : "native" + - dcr-reg : < DCR register range > + +Optional properties: + - er-offset : All 4xx SoCs with a CPM controller have + one of two different order for the CPM + registers. Some have the CPM registers + in the following order (ER,FR,SR). The + others have them in the following order + (SR,ER,FR). For the second case set + er-offset = <1>. + - unused-units : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set to turn off unused + devices. + - idle-doze : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set to turn off unused + devices. This is usually just CPM[CPU]. + - standby : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set on standby and + restored on resume. + - suspend : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set on suspend (mem) and + restored on resume. Note, for standby + and suspend the corresponding bits can + be different or the same. Usually for + standby only class 2 and 3 units are set. + However, the interface does not care. + If they are the same, the additional + power saving will be seeing if support + is available to put the DDR in self + refresh mode and any additional power + saving techniques for the specific SoC. + +Example: + CPM0: cpm { + compatible = "ibm,cpm"; + dcr-access-method = "native"; + dcr-reg = <0x160 0x003>; + er-offset = <0>; + unused-units = <0x00000100>; + idle-doze = <0x02000000>; + standby = <0xfeff0000>; + suspend = <0xfeff791d>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt new file mode 100644 index 00000000..2161334a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt @@ -0,0 +1,148 @@ + 4xx/Axon EMAC ethernet nodes + + The EMAC ethernet controller in IBM and AMCC 4xx chips, and also + the Axon bridge. To operate this needs to interact with a ths + special McMAL DMA controller, and sometimes an RGMII or ZMII + interface. In addition to the nodes and properties described + below, the node for the OPB bus on which the EMAC sits must have a + correct clock-frequency property. + + i) The EMAC node itself + + Required properties: + - device_type : "network" + + - compatible : compatible list, contains 2 entries, first is + "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, + 405gp, Axon) and second is either "ibm,emac" or + "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", + "ibm,emac4" + - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + - reg : <registers mapping> + - local-mac-address : 6 bytes, MAC address + - mal-device : phandle of the associated McMAL node + - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated + with this EMAC + - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated + with this EMAC + - cell-index : 1 cell, hardware index of the EMAC cell on a given + ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on + each Axon chip) + - max-frame-size : 1 cell, maximum frame size supported in bytes + - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048 + - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048. + - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate + thresholds). + For Axon, 0x00000010 + - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) + in bytes. + For Axon, 0x00000100 (I think ...) + - phy-mode : string, mode of operations of the PHY interface. + Supported values are: "mii", "rmii", "smii", "rgmii", + "tbi", "gmii", rtbi", "sgmii". + For Axon on CAB, it is "rgmii" + - mdio-device : 1 cell, required iff using shared MDIO registers + (440EP). phandle of the EMAC to use to drive the + MDIO lines for the PHY used by this EMAC. + - zmii-device : 1 cell, required iff connected to a ZMII. phandle of + the ZMII device node + - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII + channel or 0xffffffff if ZMII is only used for MDIO. + - rgmii-device : 1 cell, required iff connected to an RGMII. phandle + of the RGMII device node. + For Axon: phandle of plb5/plb4/opb/rgmii + - rgmii-channel : 1 cell, required iff connected to an RGMII. Which + RGMII channel is used by this EMAC. + Fox Axon: present, whatever value is appropriate for each + EMAC, that is the content of the current (bogus) "phy-port" + property. + + Optional properties: + - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, + a search is performed. + - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY + for, used if phy-address is absent. bit 0x00000001 is + MDIO address 0. + For Axon it can be absent, though my current driver + doesn't handle phy-address yet so for now, keep + 0x00ffffff in it. + - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + rx-fifo-size). For Axon, either absent or 2048. + - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + tx-fifo-size). For Axon, either absent or 2048. + - tah-device : 1 cell, optional. If connected to a TAH engine for + offload, phandle of the TAH device node. + - tah-channel : 1 cell, optional. If appropriate, channel used on the + TAH engine. + + Example: + + EMAC0: ethernet@40000800 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1c 4 1d 4>; + reg = <40000800 70>; + local-mac-address = [00 04 AC E3 1B 1E]; + mal-device = <&MAL0>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <0>; + }; + + ii) McMAL node + + Required properties: + - device_type : "dma-controller" + - compatible : compatible list, containing 2 entries, first is + "ibm,mcmal-CHIP" where CHIP is the host ASIC (like + emac) and the second is either "ibm,mcmal" or + "ibm,mcmal2". + For Axon, "ibm,mcmal-axon","ibm,mcmal2" + - interrupts : <interrupt mapping for the MAL interrupts sources: + 5 sources: tx_eob, rx_eob, serr, txde, rxde>. + For Axon: This is _different_ from the current + firmware. We use the "delayed" interrupts for txeob + and rxeob. Thus we end up with mapping those 5 MPIC + interrupts, all level positive sensitive: 10, 11, 32, + 33, 34 (in decimal) + - dcr-reg : < DCR registers range > + - dcr-parent : if needed for dcr-reg + - num-tx-chans : 1 cell, number of Tx channels + - num-rx-chans : 1 cell, number of Rx channels + + iii) ZMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,zmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,zmii". + For Axon, there is no ZMII node. + - reg : <registers mapping> + + iv) RGMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,rgmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,rgmii". + For Axon, "ibm,rgmii-axon","ibm,rgmii" + - reg : <registers mapping> + - revision : as provided by the RGMII new version register if + available. + For Axon: 0x0000012a + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt b/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt new file mode 100644 index 00000000..869f0b5f --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt @@ -0,0 +1,39 @@ +AMCC NDFC (NanD Flash Controller) + +Required properties: +- compatible : "ibm,ndfc". +- reg : should specify chip select and size used for the chip (0x2000). + +Optional properties: +- ccr : NDFC config and control register value (default 0). +- bank-settings : NDFC bank configuration register value (default 0). + +Notes: +- partition(s) - follows the OF MTD standard for partitions + +Example: + +ndfc@1,0 { + compatible = "ibm,ndfc"; + reg = <0x00000001 0x00000000 0x00002000>; + ccr = <0x00001000>; + bank-settings = <0x80002222>; + #address-cells = <1>; + #size-cells = <1>; + + nand { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x00000000 0x00200000>; + }; + partition@200000 { + label = "root"; + reg = <0x00200000 0x03E00000>; + }; + }; +}; + + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt b/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt new file mode 100644 index 00000000..515ebcf1 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt @@ -0,0 +1,93 @@ +PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator) + +Device nodes needed for operation of the ppc440spe-adma driver +are specified hereby. These are I2O/DMA, DMA and XOR nodes +for DMA engines and Memory Queue Module node. The latter is used +by ADMA driver for configuration of RAID-6 H/W capabilities of +the PPC440SPe. In addition to the nodes and properties described +below, the ranges property of PLB node must specify ranges for +DMA devices. + + i) The I2O node + + Required properties: + + - compatible : "ibm,i2o-440spe"; + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + + Example: + + I2O: i2o@400100000 { + compatible = "ibm,i2o-440spe"; + reg = <0x00000004 0x00100000 0x100>; + dcr-reg = <0x060 0x020>; + }; + + + ii) The DMA node + + Required properties: + + - compatible : "ibm,dma-440spe"; + - cell-index : 1 cell, hardware index of the DMA engine + (typically 0x0 and 0x1 for DMA0 and DMA1) + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + - interrupts : <interrupt mapping for DMA0/1 interrupts sources: + 2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0) + and DMA Error IRQ (on UIC1). The latter is common + for both DMA engines>. + - interrupt-parent : needed for interrupt mapping + + Example: + + DMA0: dma0@400100100 { + compatible = "ibm,dma-440spe"; + cell-index = <0>; + reg = <0x00000004 0x00100100 0x100>; + dcr-reg = <0x060 0x020>; + interrupt-parent = <&DMA0>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = < + 0 &UIC0 0x14 4 + 1 &UIC1 0x16 4>; + }; + + + iii) XOR Accelerator node + + Required properties: + + - compatible : "amcc,xor-accelerator"; + - reg : <registers mapping> + - interrupts : <interrupt mapping for XOR interrupt source> + - interrupt-parent : for interrupt mapping + + Example: + + xor-accel@400200000 { + compatible = "amcc,xor-accelerator"; + reg = <0x00000004 0x00200000 0x400>; + interrupt-parent = <&UIC1>; + interrupts = <0x1f 4>; + }; + + + iv) Memory Queue Module node + + Required properties: + + - compatible : "ibm,mq-440spe"; + - dcr-reg : <DCR registers range> + + Example: + + MQ0: mq { + compatible = "ibm,mq-440spe"; + dcr-reg = <0x040 0x020>; + }; + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt new file mode 100644 index 00000000..d7217260 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt @@ -0,0 +1,18 @@ +Reboot property to control system reboot on PPC4xx systems: + +By setting "reset_type" to one of the following values, the default +software reset mechanism may be overidden. Here the possible values of +"reset_type": + + 1 - PPC4xx core reset + 2 - PPC4xx chip reset + 3 - PPC4xx system reset (default) + +Example: + + cpu@0 { + device_type = "cpu"; + model = "PowerPC,440SPe"; + ... + reset-type = <2>; /* Use chip-reset */ + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/powerpc/fsl/board.txt new file mode 100644 index 00000000..380914e9 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/board.txt @@ -0,0 +1,69 @@ +Freescale Reference Board Bindings + +This document describes device tree bindings for various devices that +exist on some Freescale reference boards. + +* Board Control and Status (BCSR) + +Required properties: + + - compatible : Should be "fsl,<board>-bcsr" + - reg : Offset and length of the register set for the device + +Example: + + bcsr@f8000000 { + compatible = "fsl,mpc8360mds-bcsr"; + reg = <f8000000 8000>; + }; + +* Freescale on-board FPGA + +This is the memory-mapped registers for on board FPGA. + +Required properities: +- compatible: should be a board-specific string followed by a string + indicating the type of FPGA. Example: + "fsl,<board>-fpga", "fsl,fpga-pixis" +- reg: should contain the address and the length of the FPGA register set. +- interrupt-parent: should specify phandle for the interrupt controller. +- interrupts: should specify event (wakeup) IRQ. + +Example (P1022DS): + + board-control@3,0 { + compatible = "fsl,p1022ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + interrupt-parent = <&mpic>; + interrupts = <8 8 0 0>; + }; + +* Freescale BCSR GPIO banks + +Some BCSR registers act as simple GPIO controllers, each such +register can be represented by the gpio-controller node. + +Required properities: +- compatible : Should be "fsl,<board>-bcsr-gpio". +- reg : Should contain the address and the length of the GPIO bank + register. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the port as GPIO controller. + +Example: + + bcsr@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8360mds-bcsr"; + reg = <1 0 0x8000>; + ranges = <0 1 0 0x8000>; + + bcsr13: gpio-controller@d { + #gpio-cells = <2>; + compatible = "fsl,mpc8360mds-bcsr-gpio"; + reg = <0xd 1>; + gpio-controller; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt b/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt new file mode 100644 index 00000000..781955f5 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt @@ -0,0 +1,20 @@ +* Freescale PQ3 and QorIQ based Cache SRAM + +Freescale's mpc85xx and some QorIQ platforms provide an +option of configuring a part of (or full) cache memory +as SRAM. This cache SRAM representation in the device +tree should be done as under:- + +Required properties: + +- compatible : should be "fsl,p2020-cache-sram" +- fsl,cache-sram-ctlr-handle : points to the L2 controller +- reg : offset and length of the cache-sram. + +Example: + +cache-sram@fff00000 { + fsl,cache-sram-ctlr-handle = <&L2>; + reg = <0 0xfff00000 0 0x10000>; + compatible = "fsl,p2020-cache-sram"; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt new file mode 100644 index 00000000..160c7524 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt @@ -0,0 +1,67 @@ +* Freescale Communications Processor Module + +NOTE: This is an interim binding, and will likely change slightly, +as more devices are supported. The QE bindings especially are +incomplete. + +* Root CPM node + +Properties: +- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". +- reg : A 48-byte region beginning with CPCR. + +Example: + cpm@119c0 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; + reg = <119c0 30>; + } + +* Properties common to multiple CPM/QE devices + +- fsl,cpm-command : This value is ORed with the opcode and command flag + to specify the device on which a CPM command operates. + +- fsl,cpm-brg : Indicates which baud rate generator the device + is associated with. If absent, an unused BRG + should be dynamically allocated. If zero, the + device uses an external clock rather than a BRG. + +- reg : Unless otherwise specified, the first resource represents the + scc/fcc/ucc registers, and the second represents the device's + parameter RAM region (if it has one). + +* Multi-User RAM (MURAM) + +The multi-user/dual-ported RAM is expressed as a bus under the CPM node. + +Ranges must be set up subject to the following restrictions: + +- Children's reg nodes must be offsets from the start of all muram, even + if the user-data area does not begin at zero. +- If multiple range entries are used, the difference between the parent + address and the child address must be the same in all, so that a single + mapping can cover them all while maintaining the ability to determine + CPM-side offsets with pointer subtraction. It is recommended that + multiple range entries not be used. +- A child address of zero must be translatable, even if no reg resources + contain it. + +A child "data" node must exist, compatible with "fsl,cpm-muram-data", to +indicate the portion of muram that is usable by the OS for arbitrary +purposes. The data node may have an arbitrary number of reg resources, +all of which contribute to the allocatable muram pool. + +Example, based on mpc8272: + muram@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 10000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0 2000 9800 800>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt new file mode 100644 index 00000000..4c7d45ea --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt @@ -0,0 +1,21 @@ +* Baud Rate Generators + +Currently defined compatibles: +fsl,cpm-brg +fsl,cpm1-brg +fsl,cpm2-brg + +Properties: +- reg : There may be an arbitrary number of reg resources; BRG + numbers are assigned to these in order. +- clock-frequency : Specifies the base frequency driving + the BRG. + +Example: + brg@119f0 { + compatible = "fsl,mpc8272-brg", + "fsl,cpm2-brg", + "fsl,cpm-brg"; + reg = <119f0 10 115f0 10>; + clock-frequency = <d#25000000>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt new file mode 100644 index 00000000..87bc6048 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt @@ -0,0 +1,41 @@ +* I2C + +The I2C controller is expressed as a bus under the CPM node. + +Properties: +- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" +- reg : On CPM2 devices, the second resource doesn't specify the I2C + Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM + (typically 0x8afc 0x2). +- #address-cells : Should be one. The cell is the i2c device address with + the r/w bit set to zero. +- #size-cells : Should be zero. +- clock-frequency : Can be used to set the i2c clock frequency. If + unspecified, a default frequency of 60kHz is being used. +The following two properties are deprecated. They are only used by legacy +i2c drivers to find the bus to probe: +- linux,i2c-index : Can be used to hard code an i2c bus number. By default, + the bus number is dynamically assigned by the i2c core. +- linux,i2c-class : Can be used to override the i2c class. The class is used + by legacy i2c device drivers to find a bus in a specific context like + system management, video or sound. By default, I2C_CLASS_HWMON (1) is + being used. The definition of the classes can be found in + include/i2c/i2c.h + +Example, based on mpc823: + + i2c@860 { + compatible = "fsl,mpc823-i2c", + "fsl,cpm1-i2c"; + reg = <0x860 0x20 0x3c80 0x30>; + interrupts = <16>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-command = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt new file mode 100644 index 00000000..8e3ee168 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt @@ -0,0 +1,18 @@ +* Interrupt Controllers + +Currently defined compatibles: +- fsl,cpm1-pic + - only one interrupt cell +- fsl,pq1-pic +- fsl,cpm2-pic + - second interrupt cell is level/sense: + - 2 is falling edge + - 8 is active low + +Example: + interrupt-controller@10c00 { + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + compatible = "mpc8272-pic", "fsl,cpm2-pic"; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt new file mode 100644 index 00000000..74bfda4b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt @@ -0,0 +1,15 @@ +* USB (Universal Serial Bus Controller) + +Properties: +- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" + +Example: + usb@11bc0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,cpm2-usb"; + reg = <11b60 18 8b00 100>; + interrupts = <b 8>; + interrupt-parent = <&PIC>; + fsl,cpm-command = <2e600000>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt new file mode 100644 index 00000000..349f79fd --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt @@ -0,0 +1,38 @@ +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +On CPM1 devices, all ports are using slightly different register layouts. +Ports A, C and D are 16bit ports and Ports B and E are 32bit ports. + +On CPM2 devices, all ports are 32bit ports and use a common register layout. + +Required properties: +- compatible : "fsl,cpm1-pario-bank-a", "fsl,cpm1-pario-bank-b", + "fsl,cpm1-pario-bank-c", "fsl,cpm1-pario-bank-d", + "fsl,cpm1-pario-bank-e", "fsl,cpm2-pario-bank" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the port as GPIO controller. + +Example of three SOC GPIO banks defined as gpio-controller nodes: + + CPM1_PIO_A: gpio-controller@950 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-a"; + reg = <0x950 0x10>; + gpio-controller; + }; + + CPM1_PIO_B: gpio-controller@ab8 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-b"; + reg = <0xab8 0x10>; + gpio-controller; + }; + + CPM1_PIO_E: gpio-controller@ac8 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-e"; + reg = <0xac8 0x18>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt new file mode 100644 index 00000000..0e426944 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt @@ -0,0 +1,45 @@ +* Network + +Currently defined compatibles: +- fsl,cpm1-scc-enet +- fsl,cpm2-scc-enet +- fsl,cpm1-fec-enet +- fsl,cpm2-fcc-enet (third resource is GFEMR) +- fsl,qe-enet + +Example: + + ethernet@11300 { + device_type = "network"; + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <11300 20 8400 100 11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY0>; + fsl,cpm-command = <12000300>; + }; + +* MDIO + +Currently defined compatibles: +fsl,pq1-fec-mdio (reg is same as first resource of FEC device) +fsl,cpm2-mdio-bitbang (reg is port C registers) + +Properties for fsl,cpm2-mdio-bitbang: +fsl,mdio-pin : pin of port C controlling mdio data +fsl,mdc-pin : pin of port C controlling mdio clock + +Example: + mdio@10d40 { + device_type = "mdio"; + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <10d40 14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt new file mode 100644 index 00000000..4f893026 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt @@ -0,0 +1,115 @@ +* Freescale QUICC Engine module (QE) +This represents qe module that is installed on PowerQUICC II Pro. + +NOTE: This is an interim binding; it should be updated to fit +in with the CPM binding later in this document. + +Basically, it is a bus of devices, that could act more or less +as a complete entity (UCC, USB etc ). All of them should be siblings on +the "root" qe node, using the common properties from there. +The description below applies to the qe of MPC8360 and +more nodes and properties would be extended in the future. + +i) Root QE device + +Required properties: +- compatible : should be "fsl,qe"; +- model : precise model of the QE, Can be "QE", "CPM", or "CPM2" +- reg : offset and length of the device registers. +- bus-frequency : the clock frequency for QUICC Engine. +- fsl,qe-num-riscs: define how many RISC engines the QE has. +- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the + threads. + +Optional properties: +- fsl,firmware-phandle: + Usage: required only if there is no fsl,qe-firmware child node + Value type: <phandle> + Definition: Points to a firmware node (see "QE Firmware Node" below) + that contains the firmware that should be uploaded for this QE. + The compatible property for the firmware node should say, + "fsl,qe-firmware". + +Recommended properties +- brg-frequency : the internal clock source frequency for baud-rate + generators in Hz. + +Example: + qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,qe"; + ranges = <0 e0100000 00100000>; + reg = <e0100000 480>; + brg-frequency = <0>; + bus-frequency = <179A7B00>; + } + +* Multi-User RAM (MURAM) + +Required properties: +- compatible : should be "fsl,qe-muram", "fsl,cpm-muram". +- mode : the could be "host" or "slave". +- ranges : Should be defined as specified in 1) to describe the + translation of MURAM addresses. +- data-only : sub-node which defines the address area under MURAM + bus that can be allocated as data/parameter + +Example: + + muram@10000 { + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0 c000>; + }; + }; + +* QE Firmware Node + +This node defines a firmware binary that is embedded in the device tree, for +the purpose of passing the firmware from bootloader to the kernel, or from +the hypervisor to the guest. + +The firmware node itself contains the firmware binary contents, a compatible +property, and any firmware-specific properties. The node should be placed +inside a QE node that needs it. Doing so eliminates the need for a +fsl,firmware-phandle property. Other QE nodes that need the same firmware +should define an fsl,firmware-phandle property that points to the firmware node +in the first QE node. + +The fsl,firmware property can be specified in the DTS (possibly using incbin) +or can be inserted by the boot loader at boot time. + +Required properties: + - compatible + Usage: required + Value type: <string> + Definition: A standard property. Specify a string that indicates what + kind of firmware it is. For QE, this should be "fsl,qe-firmware". + + - fsl,firmware + Usage: required + Value type: <prop-encoded-array>, encoded as an array of bytes + Definition: A standard property. This property contains the firmware + binary "blob". + +Example: + qe1@e0080000 { + compatible = "fsl,qe"; + qe_firmware:qe-firmware { + compatible = "fsl,qe-firmware"; + fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...]; + }; + ... + }; + + qe2@e0090000 { + compatible = "fsl,qe"; + fsl,firmware-phandle = <&qe_firmware>; + ... + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt new file mode 100644 index 00000000..249db3a1 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt @@ -0,0 +1,24 @@ +* Uploaded QE firmware + + If a new firmware has been uploaded to the QE (usually by the + boot loader), then a 'firmware' child node should be added to the QE + node. This node provides information on the uploaded firmware that + device drivers may need. + + Required properties: + - id: The string name of the firmware. This is taken from the 'id' + member of the qe_firmware structure of the uploaded firmware. + Device drivers can search this string to determine if the + firmware they want is already present. + - extended-modes: The Extended Modes bitfield, taken from the + firmware binary. It is a 64-bit number represented + as an array of two 32-bit numbers. + - virtual-traps: The virtual traps, taken from the firmware binary. + It is an array of 8 32-bit numbers. + +Example: + firmware { + id = "Soft-UART"; + extended-modes = <0 0>; + virtual-traps = <0 0 0 0 0 0 0 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt new file mode 100644 index 00000000..60984260 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt @@ -0,0 +1,51 @@ +* Parallel I/O Ports + +This node configures Parallel I/O ports for CPUs with QE support. +The node should reside in the "soc" node of the tree. For each +device that using parallel I/O ports, a child node should be created. +See the definition of the Pin configuration nodes below for more +information. + +Required properties: +- device_type : should be "par_io". +- reg : offset to the register set and its length. +- num-ports : number of Parallel I/O ports + +Example: +par_io@1400 { + reg = <1400 100>; + #address-cells = <1>; + #size-cells = <0>; + device_type = "par_io"; + num-ports = <7>; + ucc_pin@01 { + ...... + }; + +Note that "par_io" nodes are obsolete, and should not be used for +the new device trees. Instead, each Par I/O bank should be represented +via its own gpio-controller node: + +Required properties: +- #gpio-cells : should be "2". +- compatible : should be "fsl,<chip>-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank". +- reg : offset to the register set and its length. +- gpio-controller : node to identify gpio controllers. + +Example: + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt new file mode 100644 index 00000000..c5b43061 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt @@ -0,0 +1,60 @@ +* Pin configuration nodes + +Required properties: +- linux,phandle : phandle of this node; likely referenced by a QE + device. +- pio-map : array of pin configurations. Each pin is defined by 6 + integers. The six numbers are respectively: port, pin, dir, + open_drain, assignment, has_irq. + - port : port number of the pin; 0-6 represent port A-G in UM. + - pin : pin number in the port. + - dir : direction of the pin, should encode as follows: + + 0 = The pin is disabled + 1 = The pin is an output + 2 = The pin is an input + 3 = The pin is I/O + + - open_drain : indicates the pin is normal or wired-OR: + + 0 = The pin is actively driven as an output + 1 = The pin is an open-drain driver. As an output, the pin is + driven active-low, otherwise it is three-stated. + + - assignment : function number of the pin according to the Pin Assignment + tables in User Manual. Each pin can have up to 4 possible functions in + QE and two options for CPM. + - has_irq : indicates if the pin is used as source of external + interrupts. + +Example: + ucc_pin@01 { + linux,phandle = <140001>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 1 6 1 0 3 0 /* TxD4 */ + 1 7 1 0 1 0 /* TxD5 */ + 1 9 1 0 2 0 /* TxD6 */ + 1 a 1 0 2 0 /* TxD7 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 a 2 0 1 0 /* RxD1 */ + 0 b 2 0 1 0 /* RxD2 */ + 0 c 2 0 1 0 /* RxD3 */ + 0 d 2 0 1 0 /* RxD4 */ + 1 1 2 0 2 0 /* RxD5 */ + 1 0 2 0 2 0 /* RxD6 */ + 1 4 2 0 2 0 /* RxD7 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 f 2 0 1 0 /* RX_DV */ + 0 10 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0>; /* GTX125 - CLK9 */ + }; + + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt new file mode 100644 index 00000000..e47734be --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt @@ -0,0 +1,70 @@ +* UCC (Unified Communications Controllers) + +Required properties: +- device_type : should be "network", "hldc", "uart", "transparent" + "bisync", "atm", or "serial". +- compatible : could be "ucc_geth" or "fsl_atm" and so on. +- cell-index : the ucc number(1-8), corresponding to UCCx in UM. +- reg : Offset and length of the register set for the device +- interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. +- pio-handle : The phandle for the Parallel I/O port configuration. +- port-number : for UART drivers, the port number to use, between 0 and 3. + This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. + The port number is added to the minor number of the device. Unlike the + CPM UART driver, the port-number is required for the QE UART driver. +- soft-uart : for UART drivers, if specified this means the QE UART device + driver should use "Soft-UART" mode, which is needed on some SOCs that have + broken UART hardware. Soft-UART is provided via a microcode upload. +- rx-clock-name: the UCC receive clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- tx-clock-name: the UCC transmit clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +The following two properties are deprecated. rx-clock has been replaced +with rx-clock-name, and tx-clock has been replaced with tx-clock-name. +Drivers that currently use the deprecated properties should continue to +do so, in order to support older device trees, but they should be updated +to check for the new properties first. +- rx-clock : represents the UCC receive clock source. + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. +- tx-clock: represents the UCC transmit clock source; + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. + +Required properties for network device_type: +- mac-address : list of bytes representing the ethernet address. +- phy-handle : The phandle for the PHY connected to this controller. + +Recommended properties: +- phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal + Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), + "tbi", or "rtbi". + +Example: + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <2000 200>; + interrupts = <a0 0>; + interrupt-parent = <700>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = "none"; + tx-clock = "clk9"; + phy-handle = <212000>; + phy-connection-type = "gmii"; + pio-handle = <140001>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt new file mode 100644 index 00000000..9ccd5f30 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt @@ -0,0 +1,37 @@ +Freescale QUICC Engine USB Controller + +Required properties: +- compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb". +- reg : the first two cells should contain usb registers location and + length, the next two two cells should contain PRAM location and + length. +- interrupts : should contain USB interrupt. +- interrupt-parent : interrupt source phandle. +- fsl,fullspeed-clock : specifies the full speed USB clock source: + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- fsl,lowspeed-clock : specifies the low speed USB clock source: + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- hub-power-budget : USB power budget for the root hub, in mA. +- gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP, + USBRN, SPEED (optional), and POWER (optional). + +Example: + +usb@6c0 { + compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb"; + reg = <0x6c0 0x40 0x8b00 0x100>; + interrupts = <11>; + interrupt-parent = <&qeic>; + fsl,fullspeed-clock = "clk21"; + gpios = <&qe_pio_b 2 0 /* USBOE */ + &qe_pio_b 3 0 /* USBTP */ + &qe_pio_b 8 0 /* USBTN */ + &qe_pio_b 9 0 /* USBRP */ + &qe_pio_b 11 0 /* USBRN */ + &qe_pio_e 20 0 /* SPEED */ + &qe_pio_e 21 0 /* POWER */>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt new file mode 100644 index 00000000..2ea76d9d --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt @@ -0,0 +1,32 @@ +* Serial + +Currently defined compatibles: +- fsl,cpm1-smc-uart +- fsl,cpm2-smc-uart +- fsl,cpm1-scc-uart +- fsl,cpm2-scc-uart +- fsl,qe-uart + +Modem control lines connected to GPIO controllers are listed in the gpios +property as described in booting-without-of.txt, section IX.1 in the following +order: + +CTS, RTS, DCD, DSR, DTR, and RI. + +The gpios property is optional and can be left out when control lines are +not used. + +Example: + + serial@11a00 { + device_type = "serial"; + compatible = "fsl,mpc8272-scc-uart", + "fsl,cpm2-scc-uart"; + reg = <11a00 20 8000 100>; + interrupts = <28 8>; + interrupt-parent = <&PIC>; + fsl,cpm-brg = <1>; + fsl,cpm-command = <00800000>; + gpios = <&gpio_c 15 0 + &gpio_d 29 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt new file mode 100644 index 00000000..9d54eb5a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt @@ -0,0 +1,395 @@ +=================================================================== +Debug Control and Status Register (DCSR) Binding +Copyright 2011 Freescale Semiconductor Inc. + +NOTE: The bindings described in this document are preliminary and subject +to change. Some of the compatible strings that contain only generic names +may turn out to be inappropriate, or need additional properties to describe +the integration of the block with the rest of the chip. + +===================================================================== +Debug Control and Status Register Memory Map + +Description + +This node defines the base address and range for the +defined DCSR Memory Map. Child nodes will describe the individual +debug blocks defined within this memory space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr" and "simple-bus". + The DCSR space exists in the memory-mapped bus. + + - #address-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + or representing physical addresses in child nodes. + + - #size-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + or representing the size of physical addresses in + child nodes. + + - ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + range of the DCSR space. + +EXAMPLE + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + +===================================================================== +Event Processing Unit + +This node represents the region of DCSR space allocated to the EPU + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-epu" + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by the EPU. + The value of the interrupts property consists of three + interrupt specifiers. The format of the specifier is defined + by the binding document describing the node's interrupt parent. + + The EPU counters can be configured to assert the performance + monitor interrupt signal based on either counter overflow or value + match. Which counter asserted the interrupt is captured in an EPU + Counter Interrupt Status Register (EPCPUISR). + + The EPU unit can also be configured to assert either or both of + two interrupt signals based on debug event sources within the SoC. + The interrupt signals are epu_xt_int0 and epu_xt_int1. + Which event source asserted the interrupt is captured in an EPU + Interrupt Status Register (EPISR0,EPISR1). + + Interrupt numbers are lised in order (perfmon, event0, event1). + + - interrupt-parent + Usage: required + Value type: <phandle> + Definition: A single <phandle> value that points + to the interrupt parent to which the child domain + is being mapped. Value must be "&mpic" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + +======================================================================= +Nexus Port Controller + +This node represents the region of DCSR space allocated to the NPC + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-npc" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + The Nexus Port controller occupies two regions in the DCSR space + with distinct functionality. + + The first register range describes the Nexus Port Controller + control and status registers. + + The second register range describes the Nexus Port Controller + internal trace buffer. The NPC trace buffer is a small memory buffer + which stages the nexus trace data for transmission via the Aurora port + or to a DDR based trace buffer. In some configurations the NPC trace + buffer can be the only trace buffer used. + + +EXAMPLE + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + +======================================================================= +Nexus Concentrator + +This node represents the region of DCSR space allocated to the NXC + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-nxc" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; +======================================================================= +CoreNet Debug Controller + +This node represents the region of DCSR space allocated to +the CoreNet Debug controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-corenet" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + The CoreNet Debug controller occupies two regions in the DCSR space + with distinct functionality. + + The first register range describes the CoreNet Debug Controller + functionalty to perform transaction and transaction attribute matches. + + The second register range describes the CoreNet Debug Controller + functionalty to trigger event notifications and debug traces. + +EXAMPLE + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + +======================================================================= +Data Path Debug controller + +This node represents the region of DCSR space allocated to +the DPAA Debug Controller. This controller controls debug configuration +for the QMAN and FMAN blocks. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-dpaa" in addition to the + generic compatible string "fsl,dcsr-dpaa". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-dpaa@9000 { + compatible = "fsl,p4080-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + +======================================================================= +OCeaN Debug controller + +This node represents the region of DCSR space allocated to +the OCN Debug Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-ocn" in addition to the + generic compatible string "fsl,dcsr-ocn". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-ocn@11000 { + compatible = "fsl,p4080-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + +======================================================================= +DDR Controller Debug controller + +This node represents the region of DCSR space allocated to +the OCN Debug Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-ddr" + + - dev-handle + Usage: required + Definition: A phandle to associate this debug node with its + component controller. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr1>; + reg = <0x12000 0x1000>; + }; + +======================================================================= +Nexus Aurora Link Controller + +This node represents the region of DCSR space allocated to +the NAL Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-nal" in addition to the + generic compatible string "fsl,dcsr-nal". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-nal@18000 { + compatible = "fsl,p4080-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + + +======================================================================= +Run Control and Power Management + +This node represents the region of DCSR space allocated to +the RCPM Debug Controller. This functionlity is limited to the +control the debug operations of the SoC and cores. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-rcpm" in addition to the + generic compatible string "fsl,dcsr-rcpm". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-rcpm@22000 { + compatible = "fsl,p4080-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + +======================================================================= +Core Service Bridge Proxy + +This node represents the region of DCSR space allocated to +the Core Service Bridge Proxies. +There is one Core Service Bridge Proxy device for each CPU in the system. +This functionlity provides access to the debug operations of the CPU. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the cpu + of the form "fsl,dcsr-<cpu>-sb-proxy" in addition to the + generic compatible string "fsl,dcsr-cpu-sb-proxy". + + - cpu-handle + Usage: required + Definition: A phandle to associate this debug node with its cpu. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", + "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", + "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + +======================================================================= diff --git a/Documentation/devicetree/bindings/powerpc/fsl/diu.txt b/Documentation/devicetree/bindings/powerpc/fsl/diu.txt new file mode 100644 index 00000000..b66cb6d3 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/diu.txt @@ -0,0 +1,34 @@ +* Freescale Display Interface Unit + +The Freescale DIU is a LCD controller, with proper hardware, it can also +drive DVI monitors. + +Required properties: +- compatible : should be "fsl,diu" or "fsl,mpc5121-diu". +- reg : should contain at least address and length of the DIU register + set. +- interrupts : one DIU interrupt should be described here. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- edid : verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + +Example (MPC8610HPCD): + display@2c000 { + compatible = "fsl,diu"; + reg = <0x2c000 100>; + interrupts = <72 2>; + interrupt-parent = <&mpic>; + }; + +Example for MPC5121: + display@2100 { + compatible = "fsl,mpc5121-diu"; + reg = <0x2100 0x100>; + interrupts = <64 0x8>; + interrupt-parent = <&ipic>; + edid = [edid-data]; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt new file mode 100644 index 00000000..2a4b4bce --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt @@ -0,0 +1,144 @@ +* Freescale 83xx DMA Controller + +Freescale PowerPC 83xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8349, mpc8360, etc.) and the second is + "fsl,elo-dma" +- reg : <registers mapping for DMA general status reg> +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. +- cell-index : controller index. 0 for controller @ 0x8100 +- interrupts : <interrupt mapping for DMA IRQ> +- interrupt-parent : optional, if needed for interrupt mapping + + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8349, mpc8350, etc.) and the second is + "fsl,elo-dma-channel". However, see note below. + - reg : <registers mapping for channel> + - cell-index : dma channel index starts at 0. + +Optional properties: + - interrupts : <interrupt mapping for DMA channel IRQ> + (on 83xx this is expected to be identical to + the interrupts property of the parent node) + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@82a8 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; + reg = <0x82a8 4>; + ranges = <0 0x8100 0x1a4>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <0>; + reg = <0 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@80 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <1>; + reg = <0x80 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@100 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <2>; + reg = <0x100 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@180 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <3>; + reg = <0x180 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + }; + +* Freescale 85xx/86xx DMA Controller + +Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8540, mpc8540, etc.) and the second is + "fsl,eloplus-dma" +- reg : <registers mapping for DMA general status reg> +- cell-index : controller index. 0 for controller @ 0x21000, + 1 for controller @ 0xc000 +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8540, mpc8560, etc.) and the second is + "fsl,eloplus-dma-channel". However, see note below. + - cell-index : dma channel index starts at 0. + - reg : <registers mapping for channel> + - interrupts : <interrupt mapping for DMA channel IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; + reg = <0x21300 4>; + ranges = <0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <23 2>; + }; + }; + +Note on DMA channel compatible properties: The compatible property must say +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA +driver (fsldma). Any DMA channel used by fsldma cannot be used by another +DMA driver, such as the SSI sound drivers for the MPC8610. Therefore, any DMA +channel that should be used for another driver should not use +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel". For the SSI drivers, for +example, the compatible property should be "fsl,ssi-dma-channel". See ssi.txt +for more information. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt b/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt new file mode 100644 index 00000000..f514f29c --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt @@ -0,0 +1,64 @@ +===================================================================== +E500 LAW & Coherency Module Device Tree Binding +Copyright (C) 2009 Freescale Semiconductor Inc. +===================================================================== + +Local Access Window (LAW) Node + +The LAW node represents the region of CCSR space where local access +windows are configured. For ECM based devices this is the first 4k +of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some +number of local access windows as specified by fsl,num-laws. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,ecm-law" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - fsl,num-laws + Usage: required + Value type: <u32> + Definition: The value specifies the number of local access + windows for this device. + +===================================================================== + +E500 Coherency Module Node + +The E500 LAW node represents the region of CCSR space where ECM config +and error reporting registers exist, this is the second 4k (0x1000) +of CCSR space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,CHIP-ecm", "fsl,ecm" where + CHIP is the processor (mpc8572, mpc8544, etc.) + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - interrupts + Usage: required + Value type: <prop-encoded-array> + + - interrupt-parent + Usage: required + Value type: <phandle> + +===================================================================== diff --git a/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt b/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt new file mode 100644 index 00000000..9a33efde --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt @@ -0,0 +1,31 @@ +* Freescale General-purpose Timers Module + +Required properties: + - compatible : should be + "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs + "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs + "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs + - reg : should contain gtm registers location and length (0x40). + - interrupts : should contain four interrupts. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies the frequency driving the timer. + +Example: + +timer@500 { + compatible = "fsl,mpc8360-gtm", "fsl,gtm"; + reg = <0x500 0x40>; + interrupts = <90 8 78 8 84 8 72 8>; + interrupt-parent = <&ipic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; + +timer@440 { + compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; + reg = <0x440 0x40>; + interrupts = <12 13 14 15>; + interrupt-parent = <&qeic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt new file mode 100644 index 00000000..7f150b50 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt @@ -0,0 +1,36 @@ +* Global Utilities Block + +The global utilities block controls power management, I/O device +enabling, power-on-reset configuration monitoring, general-purpose +I/O signal configuration, alternate function selection for multiplexed +signals, and clock control. + +Required properties: + + - compatible : Should define the compatible device type for + global-utilities. + - reg : Offset and length of the register set for the device. + +Recommended properties: + + - fsl,has-rstcr : Indicates that the global utilities register set + contains a functioning "reset control register" (i.e. the board + is wired to reset upon setting the HRESET_REQ bit in this register). + + - fsl,liodn-bits : Indicates the number of defined bits in the LIODN + registers, for those SOCs that have a PAMU device. + +Examples: + global-utilities@e0000 { /* global utilities block */ + compatible = "fsl,mpc8548-guts"; + reg = <e0000 1000>; + fsl,has-rstcr; + }; + + guts: global-utilities@e0000 { + compatible = "fsl,qoriq-device-config-1.0"; + reg = <0xe0000 0xe00>; + fsl,has-rstcr; + #sleep-cells = <1>; + fsl,liodn-bits = <12>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt b/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt new file mode 100644 index 00000000..d5e37045 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt @@ -0,0 +1,79 @@ +Integrated Flash Controller + +Properties: +- name : Should be ifc +- compatible : should contain "fsl,ifc". The version of the integrated + flash controller can be found in the IFC_REV register at + offset zero. + +- #address-cells : Should be either two or three. The first cell is the + chipselect number, and the remaining cells are the + offset into the chipselect. +- #size-cells : Either one or two, depending on how large each chipselect + can be. +- reg : Offset and length of the register set for the device +- interrupts: IFC may have one or two interrupts. If two interrupt + specifiers are present, the first is the "common" + interrupt (CM_EVTER_STAT), and the second is the NAND + interrupt (NAND_EVTER_STAT). If there is only one, + that interrupt reports both types of event. + + +- ranges : Each range corresponds to a single chipselect, and covers + the entire access window as configured. + +Child device nodes describe the devices connected to IFC such as NOR (e.g. +cfi-flash) and NAND (fsl,ifc-nand). There might be board specific devices +like FPGAs, CPLDs, etc. + +Example: + + ifc@ffe1e000 { + compatible = "fsl,ifc", "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x0 0xffe1e000 0 0x2000>; + interrupts = <16 2 19 2>; + + /* NOR, NAND Flashes and CPLD on board */ + ranges = <0x0 0x0 0x0 0xee000000 0x02000000 + 0x1 0x0 0x0 0xffa00000 0x00010000 + 0x3 0x0 0x0 0xffb00000 0x00020000>; + + flash@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x2000000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + /* 32MB for user data */ + reg = <0x0 0x02000000>; + label = "NOR Data"; + }; + }; + + flash@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,ifc-nand"; + reg = <0x1 0x0 0x10000>; + + partition@0 { + /* This location must not be altered */ + /* 1MB for u-boot Bootloader Image */ + reg = <0x0 0x00100000>; + label = "NAND U-Boot Image"; + read-only; + }; + }; + + cpld@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p1010rdb-cpld"; + reg = <0x3 0x0 0x000001f>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt b/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt new file mode 100644 index 00000000..3300fec5 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt @@ -0,0 +1,35 @@ +* Chipselect/Local Bus + +Properties: +- name : Should be localbus +- #address-cells : Should be either two or three. The first cell is the + chipselect number, and the remaining cells are the + offset into the chipselect. +- #size-cells : Either one or two, depending on how large each chipselect + can be. +- ranges : Each range corresponds to a single chipselect, and cover + the entire access window as configured. + +Example: + localbus@f0010100 { + compatible = "fsl,mpc8272-localbus", + "fsl,pq2-localbus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <f0010100 40>; + + ranges = <0 0 fe000000 02000000 + 1 0 f4500000 00008000>; + + flash@0,0 { + compatible = "jedec-flash"; + reg = <0 0 2000000>; + bank-width = <4>; + device-width = <1>; + }; + + board-control@1,0 { + reg = <1 0 20>; + compatible = "fsl,mpc8272ads-bcsr"; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt b/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt new file mode 100644 index 00000000..4ceda9b3 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt @@ -0,0 +1,64 @@ +===================================================================== +MPX LAW & Coherency Module Device Tree Binding +Copyright (C) 2009 Freescale Semiconductor Inc. +===================================================================== + +Local Access Window (LAW) Node + +The LAW node represents the region of CCSR space where local access +windows are configured. For MCM based devices this is the first 4k +of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some +number of local access windows as specified by fsl,num-laws. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,mcm-law" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - fsl,num-laws + Usage: required + Value type: <u32> + Definition: The value specifies the number of local access + windows for this device. + +===================================================================== + +MPX Coherency Module Node + +The MPX LAW node represents the region of CCSR space where MCM config +and error reporting registers exist, this is the second 4k (0x1000) +of CCSR space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,CHIP-mcm", "fsl,mcm" where + CHIP is the processor (mpc8641, mpc8610, etc.) + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - interrupts + Usage: required + Value type: <prop-encoded-array> + + - interrupt-parent + Usage: required + Value type: <phandle> + +===================================================================== diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt b/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt new file mode 100644 index 00000000..0f766333 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt @@ -0,0 +1,17 @@ +Freescale MPC8349E-mITX-compatible Power Management Micro Controller Unit (MCU) + +Required properties: +- compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx". +- reg : should specify I2C address (0x0a). +- #gpio-cells : should be 2. +- gpio-controller : should be present. + +Example: + +mcu@0a { + #gpio-cells = <2>; + compatible = "fsl,mc9s08qg8-mpc8349emitx", + "fsl,mcu-mpc8349emitx"; + reg = <0x0a>; + gpio-controller; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt new file mode 100644 index 00000000..8832e879 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt @@ -0,0 +1,70 @@ +MPC5121 PSC Device Tree Bindings + +PSC in UART mode +---------------- + +For PSC in UART mode the needed PSC serial devices +are specified by fsl,mpc5121-psc-uart nodes in the +fsl,mpc5121-immr SoC node. Additionally the PSC FIFO +Controller node fsl,mpc5121-psc-fifo is requered there: + +fsl,mpc5121-psc-uart nodes +-------------------------- + +Required properties : + - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" + - cell-index : Index of the PSC in hardware + - reg : Offset and length of the register set for the PSC device + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Recommended properties : + - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) + - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) + + +fsl,mpc5121-psc-fifo node +------------------------- + +Required properties : + - compatible : Should be "fsl,mpc5121-psc-fifo" + - reg : Offset and length of the register set for the PSC + FIFO Controller + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + + +Example for a board using PSC0 and PSC1 devices in serial mode: + +serial@11000 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <0>; + reg = <0x11000 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +serial@11100 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <1>; + reg = <0x11100 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +pscfifo@11f00 { + compatible = "fsl,mpc5121-psc-fifo"; + reg = <0x11f00 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt new file mode 100644 index 00000000..4ccb2cd5 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt @@ -0,0 +1,198 @@ +MPC5200 Device Tree Bindings +---------------------------- + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +Naming conventions +------------------ +For mpc5200 on-chip devices, the format for each compatible value is +<chip>-<device>[-<mode>]. The OS should be able to match a device driver +to the device based solely on the compatible value. If two drivers +match on the compatible list; the 'most compatible' driver should be +selected. + +The split between the MPC5200 and the MPC5200B leaves a bit of a +conundrum. How should the compatible property be set up to provide +maximum compatibility information; but still accurately describe the +chip? For the MPC5200; the answer is easy. Most of the SoC devices +originally appeared on the MPC5200. Since they didn't exist anywhere +else; the 5200 compatible properties will contain only one item; +"fsl,mpc5200-<device>". + +The 5200B is almost the same as the 5200, but not quite. It fixes +silicon bugs and it adds a small number of enhancements. Most of the +devices either provide exactly the same interface as on the 5200. A few +devices have extra functions but still have a backwards compatible mode. +To express this information as completely as possible, 5200B device trees +should have two items in the compatible list: + compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>"; + +It is *strongly* recommended that 5200B device trees follow this convention +(instead of only listing the base mpc5200 item). + +ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec"; + ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec"; + +Modal devices, like PSCs, also append the configured function to the +end of the compatible field. ie. A PSC in i2s mode would specify +"fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s". This convention is chosen to +avoid naming conflicts with non-psc devices providing the same +function. For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe +the mpc5200 simple spi device and a PSC spi mode respectively. + +At the time of writing, exact chip may be either 'fsl,mpc5200' or +'fsl,mpc5200b'. + +The soc node +------------ +This node describes the on chip SOC peripherals. Every mpc5200 based +board will have this node, and as such there is a common naming +convention for SOC devices. + +Required properties: +name description +---- ----------- +ranges Memory range of the internal memory mapped registers. + Should be <0 [baseaddr] 0xc000> +reg Should be <[baseaddr] 0x100> +compatible mpc5200: "fsl,mpc5200-immr" + mpc5200b: "fsl,mpc5200b-immr" +system-frequency 'fsystem' frequency in Hz; XLB, IPB, USB and PCI + clocks are derived from the fsystem clock. +bus-frequency IPB bus frequency in Hz. Clock rate + used by most of the soc devices. + +soc child nodes +--------------- +Any on chip SOC devices available to Linux must appear as soc5200 child nodes. + +Note: The tables below show the value for the mpc5200. A mpc5200b device +tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form. + +Required soc5200 child nodes: +name compatible Description +---- ---------- ----------- +cdm@<addr> fsl,mpc5200-cdm Clock Distribution +interrupt-controller@<addr> fsl,mpc5200-pic need an interrupt + controller to boot +bestcomm@<addr> fsl,mpc5200-bestcomm Bestcomm DMA controller + +Recommended soc5200 child nodes; populate as needed for your board +name compatible Description +---- ---------- ----------- +timer@<addr> fsl,mpc5200-gpt General purpose timers +gpio@<addr> fsl,mpc5200-gpio MPC5200 simple gpio controller +gpio@<addr> fsl,mpc5200-gpio-wkup MPC5200 wakeup gpio controller +rtc@<addr> fsl,mpc5200-rtc Real time clock +mscan@<addr> fsl,mpc5200-mscan CAN bus controller +pci@<addr> fsl,mpc5200-pci PCI bridge +serial@<addr> fsl,mpc5200-psc-uart PSC in serial mode +i2s@<addr> fsl,mpc5200-psc-i2s PSC in i2s mode +ac97@<addr> fsl,mpc5200-psc-ac97 PSC in ac97 mode +spi@<addr> fsl,mpc5200-psc-spi PSC in spi mode +irda@<addr> fsl,mpc5200-psc-irda PSC in IrDA mode +spi@<addr> fsl,mpc5200-spi MPC5200 spi device +ethernet@<addr> fsl,mpc5200-fec MPC5200 ethernet device +ata@<addr> fsl,mpc5200-ata IDE ATA interface +i2c@<addr> fsl,mpc5200-i2c I2C controller +usb@<addr> fsl,mpc5200-ohci,ohci-be USB controller +xlb@<addr> fsl,mpc5200-xlb XLB arbitrator + +fsl,mpc5200-gpt nodes +--------------------- +On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board +design supports the internal wdt, then the device node for GPT0 should +include the empty property 'fsl,has-wdt'. Note that this does not activate +the watchdog. The timer will function as a GPT if the timer api is used, and +it will function as watchdog if the watchdog device is used. The watchdog +mode has priority over the gpt mode, i.e. if the watchdog is activated, any +gpt api call to this timer will fail with -EBUSY. + +If you add the property + fsl,wdt-on-boot = <n>; +GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. +If n>0, the watchdog is started with a timeout of n seconds. If n=0, the +configuration of the watchdog is not touched. This is useful in two cases: +- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; +- do not touch a configuration assigned by the boot loader which supervises + the boot process itself. + +The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. + +An mpc5200-gpt can be used as a single line GPIO controller. To do so, +add the following properties to the gpt node: + gpio-controller; + #gpio-cells = <2>; +When referencing the GPIO line from another node, the first cell must always +be zero and the second cell represents the gpio flags and described in the +gpio device tree binding. + +An mpc5200-gpt can be used as a single line edge sensitive interrupt +controller. To do so, add the following properties to the gpt node: + interrupt-controller; + #interrupt-cells = <1>; +When referencing the IRQ line from another node, the cell represents the +sense mode; 1 for edge rising, 2 for edge falling. + +fsl,mpc5200-psc nodes +--------------------- +The PSCs should include a cell-index which is the index of the PSC in +hardware. cell-index is used to determine which shared SoC registers to +use when setting up PSC clocking. cell-index number starts at '0'. ie: + PSC1 has 'cell-index = <0>' + PSC4 has 'cell-index = <3>' + +PSC in i2s mode: The mpc5200 and mpc5200b PSCs are not compatible when in +i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the +compatible field. + + +fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes +------------------------------------------------ +Each GPIO controller node should have the empty property gpio-controller and +#gpio-cells set to 2. First cell is the GPIO number which is interpreted +according to the bit numbers in the GPIO control registers. The second cell +is for flags which is currently unused. + +fsl,mpc5200-fec nodes +--------------------- +The FEC node can specify one of the following properties to configure +the MII link: +- fsl,7-wire-mode - An empty property that specifies the link uses 7-wire + mode instead of MII +- current-speed - Specifies that the MII should be configured for a fixed + speed. This property should contain two cells. The + first cell specifies the speed in Mbps and the second + should be '0' for half duplex and '1' for full duplex +- phy-handle - Contains a phandle to an Ethernet PHY. + +Interrupt controller (fsl,mpc5200-pic) node +------------------------------------------- +The mpc5200 pic binding splits hardware IRQ numbers into two levels. The +split reflects the layout of the PIC hardware itself, which groups +interrupts into one of three groups; CRIT, MAIN or PERP. Also, the +Bestcomm dma engine has it's own set of interrupt sources which are +cascaded off of peripheral interrupt 0, which the driver interprets as a +fourth group, SDMA. + +The interrupts property for device nodes using the mpc5200 pic consists +of three cells; <L1 L2 level> + + L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3] + L2 := interrupt number; directly mapped from the value in the + "ICTL PerStat, MainStat, CritStat Encoded Register" + level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3] + +For external IRQs, use the following interrupt property values (how to +specify external interrupts is a frequently asked question): +External interrupts: + external irq0: interrupts = <0 0 n>; + external irq1: interrupts = <1 1 n>; + external irq2: interrupts = <1 2 n>; + external irq3: interrupts = <1 3 n>; +'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) + +fsl,mpc5200-mscan nodes +----------------------- +See file can.txt in this directory. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt new file mode 100644 index 00000000..bc8ded64 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt @@ -0,0 +1,63 @@ +* FSL MPIC Message Registers + +This binding specifies what properties must be available in the device tree +representation of the message register blocks found in some FSL MPIC +implementations. + +Required properties: + + - compatible: Specifies the compatibility list for the message register + block. The type shall be <string-list> and the value shall be of the form + "fsl,mpic-v<version>-msgr", where <version> is the version number of + the MPIC containing the message registers. + + - reg: Specifies the base physical address(s) and size(s) of the + message register block's addressable register space. The type shall be + <prop-encoded-array>. + + - interrupts: Specifies a list of interrupt-specifiers which are available + for receiving interrupts. Interrupt-specifier consists of two cells: first + cell is interrupt-number and second cell is level-sense. The type shall be + <prop-encoded-array>. + +Optional properties: + + - mpic-msgr-receive-mask: Specifies what registers in the containing block + are allowed to receive interrupts. The value is a bit mask where a set + bit at bit 'n' indicates that message register 'n' can receive interrupts. + Note that "bit 'n'" is numbered from LSB for PPC hardware. The type shall + be <u32>. If not present, then all of the message registers in the block + are available. + +Aliases: + + An alias should be created for every message register block. They are not + required, though. However, a particular implementation of this binding + may require aliases to be present. Aliases are of the form + 'mpic-msgr-block<n>', where <n> is an integer specifying the block's number. + Numbers shall start at 0. + +Example: + + aliases { + mpic-msgr-block0 = &mpic_msgr_block0; + mpic-msgr-block1 = &mpic_msgr_block1; + }; + + mpic_msgr_block0: mpic-msgr-block@41400 { + compatible = "fsl,mpic-v3.1-msgr"; + reg = <0x41400 0x200>; + // Message registers 0 and 2 in this block can receive interrupts on + // sources 0xb0 and 0xb2, respectively. + interrupts = <0xb0 2 0xb2 2>; + mpic-msgr-receive-mask = <0x5>; + }; + + mpic_msgr_block1: mpic-msgr-block@42400 { + compatible = "fsl,mpic-v3.1-msgr"; + reg = <0x42400 0x200>; + // Message registers 0 and 2 in this block can receive interrupts on + // sources 0xb4 and 0xb6, respectively. + interrupts = <0xb4 2 0xb6 2>; + mpic-msgr-receive-mask = <0x5>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic-timer.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic-timer.txt new file mode 100644 index 00000000..df419581 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic-timer.txt @@ -0,0 +1,38 @@ +* Freescale MPIC timers + +Required properties: +- compatible: "fsl,mpic-global-timer" + +- reg : Contains two regions. The first is the main timer register bank + (GTCCRxx, GTBCRxx, GTVPRxx, GTDRxx). The second is the timer control + register (TCRx) for the group. + +- fsl,available-ranges: use <start count> style section to define which + timer interrupts can be used. This property is optional; without this, + all timers within the group can be used. + +- interrupts: one interrupt per timer in the group, in order, starting + with timer zero. If timer-available-ranges is present, only the + interrupts that correspond to available timers shall be present. + +Example: + /* Note that this requires #interrupt-cells to be 4 */ + timer0: timer@41100 { + compatible = "fsl,mpic-global-timer"; + reg = <0x41100 0x100 0x41300 4>; + + /* Another AMP partition is using timers 0 and 1 */ + fsl,available-ranges = <2 2>; + + interrupts = <2 0 3 0 + 3 0 3 0>; + }; + + timer1: timer@42100 { + compatible = "fsl,mpic-global-timer"; + reg = <0x42100 0x100 0x42300 4>; + interrupts = <4 0 3 0 + 5 0 3 0 + 6 0 3 0 + 7 0 3 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt new file mode 100644 index 00000000..dc574463 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt @@ -0,0 +1,231 @@ +===================================================================== +Freescale MPIC Interrupt Controller Node +Copyright (C) 2010,2011 Freescale Semiconductor Inc. +===================================================================== + +The Freescale MPIC interrupt controller is found on all PowerQUICC +and QorIQ processors and is compatible with the Open PIC. The +notable difference from Open PIC binding is the addition of 2 +additional cells in the interrupt specifier defining interrupt type +information. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Shall include "fsl,mpic". Freescale MPIC + controllers compatible with this binding have Block + Revision Registers BRR1 and BRR2 at offset 0x0 and + 0x10 in the MPIC. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical + offset and length of the device's registers within the + CCSR address space. + + - interrupt-controller + Usage: required + Value type: <empty> + Definition: Specifies that this node is an interrupt + controller + + - #interrupt-cells + Usage: required + Value type: <u32> + Definition: Shall be 2 or 4. A value of 2 means that interrupt + specifiers do not contain the interrupt-type or type-specific + information cells. + + - #address-cells + Usage: required + Value type: <u32> + Definition: Shall be 0. + + - pic-no-reset + Usage: optional + Value type: <empty> + Definition: The presence of this property specifies that the + MPIC must not be reset by the client program, and that + the boot program has initialized all interrupt source + configuration registers to a sane state-- masked or + directed at other cores. This ensures that the client + program will not receive interrupts for sources not belonging + to the client. The presence of this property also mandates + that any initialization related to interrupt sources shall + be limited to sources explicitly referenced in the device tree. + + - big-endian + Usage: optional + Value type: <empty> + If present the MPIC will be assumed to be big-endian. Some + device-trees omit this property on MPIC nodes even when the MPIC is + in fact big-endian, so certain boards override this property. + + - single-cpu-affinity + Usage: optional + Value type: <empty> + If present the MPIC will be assumed to only be able to route + non-IPI interrupts to a single CPU at a time (EG: Freescale MPIC). + + - last-interrupt-source + Usage: optional + Value type: <u32> + Some MPICs do not correctly report the number of hardware sources + in the global feature registers. If specified, this field will + override the value read from MPIC_GREG_FEATURE_LAST_SRC. + +INTERRUPT SPECIFIER DEFINITION + + Interrupt specifiers consists of 4 cells encoded as + follows: + + <1st-cell> interrupt-number + + Identifies the interrupt source. The meaning + depends on the type of interrupt. + + Note: If the interrupt-type cell is undefined + (i.e. #interrupt-cells = 2), this cell + should be interpreted the same as for + interrupt-type 0-- i.e. an external or + normal SoC device interrupt. + + <2nd-cell> level-sense information, encoded as follows: + 0 = low-to-high edge triggered + 1 = active low level-sensitive + 2 = active high level-sensitive + 3 = high-to-low edge triggered + + <3rd-cell> interrupt-type + + The following types are supported: + + 0 = external or normal SoC device interrupt + + The interrupt-number cell contains + the SoC device interrupt number. The + type-specific cell is undefined. The + interrupt-number is derived from the + MPIC a block of registers referred to as + the "Interrupt Source Configuration Registers". + Each source has 32-bytes of registers + (vector/priority and destination) in this + region. So interrupt 0 is at offset 0x0, + interrupt 1 is at offset 0x20, and so on. + + 1 = error interrupt + + The interrupt-number cell contains + the SoC device interrupt number for + the error interrupt. The type-specific + cell identifies the specific error + interrupt number. + + 2 = MPIC inter-processor interrupt (IPI) + + The interrupt-number cell identifies + the MPIC IPI number. The type-specific + cell is undefined. + + 3 = MPIC timer interrupt + + The interrupt-number cell identifies + the MPIC timer number. The type-specific + cell is undefined. + + <4th-cell> type-specific information + + The type-specific cell is encoded as follows: + + - For interrupt-type 1 (error interrupt), + the type-specific cell contains the + bit number of the error interrupt in the + Error Interrupt Summary Register. + +EXAMPLE 1 + /* + * mpic interrupt controller with 4 cells per specifier + */ + mpic: pic@40000 { + compatible = "fsl,mpic"; + interrupt-controller; + #interrupt-cells = <4>; + #address-cells = <0>; + reg = <0x40000 0x40000>; + }; + +EXAMPLE 2 + /* + * The MPC8544 I2C controller node has an internal + * interrupt number of 27. As per the reference manual + * this corresponds to interrupt source configuration + * registers at 0x5_0560. + * + * The interrupt source configuration registers begin + * at 0x5_0000. + * + * To compute the interrupt specifier interrupt number + * + * 0x560 >> 5 = 43 + * + * The interrupt source configuration registers begin + * at 0x5_0000, and so the i2c vector/priority registers + * are at 0x5_0560. + */ + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + dfsrr; + }; + + +EXAMPLE 3 + /* + * Definition of a node defining the 4 + * MPIC IPI interrupts. Note the interrupt + * type of 2. + */ + ipi@410a0 { + compatible = "fsl,mpic-ipi"; + reg = <0x40040 0x10>; + interrupts = <0 0 2 0 + 1 0 2 0 + 2 0 2 0 + 3 0 2 0>; + }; + +EXAMPLE 4 + /* + * Definition of a node defining the MPIC + * global timers. Note the interrupt + * type of 3. + */ + timer0: timer@41100 { + compatible = "fsl,mpic-global-timer"; + reg = <0x41100 0x100 0x41300 4>; + interrupts = <0 0 3 0 + 1 0 3 0 + 2 0 3 0 + 3 0 3 0>; + }; + +EXAMPLE 5 + /* + * Definition of an error interrupt (interrupt type 1). + * SoC interrupt number is 16 and the specific error + * interrupt bit in the error interrupt summary register + * is 23. + */ + memory-controller@8000 { + compatible = "fsl,p4080-memory-controller"; + reg = <0x8000 0x1000>; + interrupts = <16 2 1 23>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt new file mode 100644 index 00000000..5693877a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt @@ -0,0 +1,87 @@ +* Freescale MSI interrupt controller + +Required properties: +- compatible : compatible list, contains 2 entries, + first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, + etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on + the parent type. + +- reg : It may contain one or two regions. The first region should contain + the address and the length of the shared message interrupt register set. + The second region should contain the address of aliased MSIIR register for + platforms that have such an alias. + +- msi-available-ranges: use <start count> style section to define which + msi interrupt can be used in the 256 msi interrupts. This property is + optional, without this, all the 256 MSI interrupts can be used. + Each available range must begin and end on a multiple of 32 (i.e. + no splitting an individual MSI register or the associated PIC interrupt). + +- interrupts : each one of the interrupts here is one entry per 32 MSIs, + and routed to the host interrupt controller. the interrupts should + be set as edge sensitive. If msi-available-ranges is present, only + the interrupts that correspond to available ranges shall be present. + +- interrupt-parent: the phandle for the interrupt controller + that services interrupts for this device. for 83xx cpu, the interrupts + are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed + to MPIC. + +Optional properties: +- msi-address-64: 64-bit PCI address of the MSIIR register. The MSIIR register + is used for MSI messaging. The address of MSIIR in PCI address space is + the MSI message address. + + This property may be used in virtualized environments where the hypervisor + has created an alternate mapping for the MSIR block. See below for an + explanation. + + +Example: + msi@41600 { + compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + interrupt-parent = <&mpic>; + }; + +The Freescale hypervisor and msi-address-64 +------------------------------------------- +Normally, PCI devices have access to all of CCSR via an ATMU mapping. The +Freescale MSI driver calculates the address of MSIIR (in the MSI register +block) and sets that address as the MSI message address. + +In a virtualized environment, the hypervisor may need to create an IOMMU +mapping for MSIIR. The Freescale ePAPR hypervisor has this requirement +because of hardware limitations of the Peripheral Access Management Unit +(PAMU), which is currently the only IOMMU that the hypervisor supports. +The ATMU is programmed with the guest physical address, and the PAMU +intercepts transactions and reroutes them to the true physical address. + +In the PAMU, each PCI controller is given only one primary window. The +PAMU restricts DMA operations so that they can only occur within a window. +Because PCI devices must be able to DMA to memory, the primary window must +be used to cover all of the guest's memory space. + +PAMU primary windows can be divided into 256 subwindows, and each +subwindow can have its own address mapping ("guest physical" to "true +physical"). However, each subwindow has to have the same alignment, which +means they cannot be located at just any address. Because of these +restrictions, it is usually impossible to create a 4KB subwindow that +covers MSIIR where it's normally located. + +Therefore, the hypervisor has to create a subwindow inside the same +primary window used for memory, but mapped to the MSIR block (where MSIIR +lives). The first subwindow after the end of guest memory is used for +this. The address specified in the msi-address-64 property is the PCI +address of MSIIR. The hypervisor configures the PAMU to map that address to +the true physical address of MSIIR. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt b/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt new file mode 100644 index 00000000..1f5e329f --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt @@ -0,0 +1,140 @@ +Freescale Peripheral Management Access Unit (PAMU) Device Tree Binding + +DESCRIPTION + +The PAMU is an I/O MMU that provides device-to-memory access control and +address translation capabilities. + +Required properties: + +- compatible : <string> + First entry is a version-specific string, such as + "fsl,pamu-v1.0". The second is "fsl,pamu". +- ranges : <prop-encoded-array> + A standard property. Utilized to describe the memory mapped + I/O space utilized by the controller. The size should + be set to the total size of the register space of all + physically present PAMU controllers. For example, for + PAMU v1.0, on an SOC that has five PAMU devices, the size + is 0x5000. +- interrupts : <prop-encoded-array> + Interrupt mappings. The first tuple is the normal PAMU + interrupt, used for reporting access violations. The second + is for PAMU hardware errors, such as PAMU operation errors + and ECC errors. +- #address-cells: <u32> + A standard property. +- #size-cells : <u32> + A standard property. + +Optional properties: +- reg : <prop-encoded-array> + A standard property. It represents the CCSR registers of + all child PAMUs combined. Include it to provide support + for legacy drivers. +- interrupt-parent : <phandle> + Phandle to interrupt controller + +Child nodes: + +Each child node represents one PAMU controller. Each SOC device that is +connected to a specific PAMU device should have a "fsl,pamu-phandle" property +that links to the corresponding specific child PAMU controller. + +- reg : <prop-encoded-array> + A standard property. Specifies the physical address and + length (relative to the parent 'ranges' property) of this + PAMU controller's configuration registers. The size should + be set to the size of this PAMU controllers's register space. + For PAMU v1.0, this size is 0x1000. +- fsl,primary-cache-geometry + : <prop-encoded-array> + Two cells that specify the geometry of the primary PAMU + cache. The first is the number of cache lines, and the + second is the number of "ways". For direct-mapped caches, + specify a value of 1. +- fsl,secondary-cache-geometry + : <prop-encoded-array> + Two cells that specify the geometry of the secondary PAMU + cache. The first is the number of cache lines, and the + second is the number of "ways". For direct-mapped caches, + specify a value of 1. + +Device nodes: + +Devices that have LIODNs need to specify links to the parent PAMU controller +(the actual PAMU controller that this device is connected to) and a pointer to +the LIODN register, if applicable. + +- fsl,iommu-parent + : <phandle> + Phandle to the single, specific PAMU controller node to which + this device is connect. The PAMU topology is represented in + the device tree to assist code that dynamically determines the + best LIODN values to minimize PAMU cache thrashing. + +- fsl,liodn-reg : <prop-encoded-array> + Two cells that specify the location of the LIODN register + for this device. Required for devices that have a single + LIODN. The first cell is a phandle to a node that contains + the registers where the LIODN is to be set. The second is + the offset from the first "reg" resource of the node where + the specific LIODN register is located. + + +Example: + + iommu@20000 { + compatible = "fsl,pamu-v1.0", "fsl,pamu"; + reg = <0x20000 0x5000>; + ranges = <0 0x20000 0x5000>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = < + 24 2 0 0 + 16 2 1 30>; + + pamu0: pamu@0 { + reg = <0 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu1: pamu@1000 { + reg = <0x1000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu2: pamu@2000 { + reg = <0x2000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu3: pamu@3000 { + reg = <0x3000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu4: pamu@4000 { + reg = <0x4000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + }; + + guts: global-utilities@e0000 { + compatible = "fsl,qoriq-device-config-1.0"; + reg = <0xe0000 0xe00>; + fsl,has-rstcr; + #sleep-cells = <1>; + fsl,liodn-bits = <12>; + }; + +/include/ "qoriq-dma-0.dtsi" + dma@100300 { + fsl,iommu-parent = <&pamu0>; + fsl,liodn-reg = <&guts 0x584>; /* DMA2LIODNR */ + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt b/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt new file mode 100644 index 00000000..07256b7f --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt @@ -0,0 +1,63 @@ +* Power Management Controller + +Properties: +- compatible: "fsl,<chip>-pmc". + + "fsl,mpc8349-pmc" should be listed for any chip whose PMC is + compatible. "fsl,mpc8313-pmc" should also be listed for any chip + whose PMC is compatible, and implies deep-sleep capability. + + "fsl,mpc8548-pmc" should be listed for any chip whose PMC is + compatible. "fsl,mpc8536-pmc" should also be listed for any chip + whose PMC is compatible, and implies deep-sleep capability. + + "fsl,mpc8641d-pmc" should be listed for any chip whose PMC is + compatible; all statements below that apply to "fsl,mpc8548-pmc" also + apply to "fsl,mpc8641d-pmc". + + Compatibility does not include bit assignments in SCCR/PMCDR/DEVDISR; these + bit assignments are indicated via the sleep specifier in each device's + sleep property. + +- reg: For devices compatible with "fsl,mpc8349-pmc", the first resource + is the PMC block, and the second resource is the Clock Configuration + block. + + For devices compatible with "fsl,mpc8548-pmc", the first resource + is a 32-byte block beginning with DEVDISR. + +- interrupts: For "fsl,mpc8349-pmc"-compatible devices, the first + resource is the PMC block interrupt. + +- fsl,mpc8313-wakeup-timer: For "fsl,mpc8313-pmc"-compatible devices, + this is a phandle to an "fsl,gtm" node on which timer 4 can be used as + a wakeup source from deep sleep. + +Sleep specifiers: + + fsl,mpc8349-pmc: Sleep specifiers consist of one cell. For each bit + that is set in the cell, the corresponding bit in SCCR will be saved + and cleared on suspend, and restored on resume. This sleep controller + supports disabling and resuming devices at any time. + + fsl,mpc8536-pmc: Sleep specifiers consist of three cells, the third of + which will be ORed into PMCDR upon suspend, and cleared from PMCDR + upon resume. The first two cells are as described for fsl,mpc8578-pmc. + This sleep controller only supports disabling devices during system + sleep, or permanently. + + fsl,mpc8548-pmc: Sleep specifiers consist of one or two cells, the + first of which will be ORed into DEVDISR (and the second into + DEVDISR2, if present -- this cell should be zero or absent if the + hardware does not have DEVDISR2) upon a request for permanent device + disabling. This sleep controller does not support configuring devices + to disable during system sleep (unless supported by another compatible + match), or dynamically. + +Example: + + power@b00 { + compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc"; + reg = <0xb00 0x100 0xa00 0x100>; + interrupts = <80 8>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt new file mode 100644 index 00000000..4ad29b9a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt @@ -0,0 +1,81 @@ +* Freescale 85xx RAID Engine nodes + +RAID Engine nodes are defined to describe on-chip RAID accelerators. Each RAID +Engine should have a separate node. + +Supported chips: +P5020, P5040 + +Required properties: + +- compatible: Should contain "fsl,raideng-v1.0" as the value + This identifies RAID Engine block. 1 in 1.0 represents + major number whereas 0 represents minor number. The + version matches the hardware IP version. +- reg: offset and length of the register set for the device +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng: raideng@320000 { + compatible = "fsl,raideng-v1.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x320000 0x10000>; + ranges = <0 0x320000 0x10000>; + }; + + +There must be a sub-node for each job queue present in RAID Engine +This node must be a sub-node of the main RAID Engine node + +- compatible: Should contain "fsl,raideng-v1.0-job-queue" as the value + This identifies the job queue interface +- reg: offset and length of the register set for job queue +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + }; + + +There must be a sub-node for each job ring present in RAID Engine +This node must be a sub-node of job queue node + +- compatible: Must contain "fsl,raideng-v1.0-job-ring" as the value + This identifies job ring. Should contain either + "fsl,raideng-v1.0-hp-ring" or "fsl,raideng-v1.0-lp-ring" + depending upon whether ring has high or low priority +- reg: offset and length of the register set for job ring +- interrupts: interrupt mapping for job ring IRQ + +Optional property: + +- fsl,liodn: Specifies the LIODN to be used for Job Ring. This + property is normally set by firmware. Value + is of 12-bits which is the LIODN number for this JR. + This property is used by the IOMMU (PAMU) to distinquish + transactions from this JR and than be able to do address + translation & protection accordingly. + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + + raideng_jr0: jr@0 { + compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-hp-ring"; + reg = <0x0 0x400>; + interrupts = <139 2 0 0>; + interrupt-parent = <&mpic>; + fsl,liodn = <0x41>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt new file mode 100644 index 00000000..b9a8a2bc --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt @@ -0,0 +1,163 @@ +Message unit node: + +For SRIO controllers that implement the message unit as part of the controller +this node is required. For devices with RMAN this node should NOT exist. The +node is composed of three types of sub-nodes ("fsl-srio-msg-unit", +"fsl-srio-dbell-unit" and "fsl-srio-port-write-unit"). + +See srio.txt for more details about generic SRIO controller details. + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,srio-rmu-vX.Y", "fsl,srio-rmu". + + The version X.Y should match the general SRIO controller's IP Block + revision register's Major(X) and Minor (Y) value. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers for message units + and doorbell units. + + - fsl,liodn + Usage: optional-but-recommended (for devices with PAMU) + Value type: <prop-encoded-array> + Definition: The logical I/O device number for the PAMU (IOMMU) to be + correctly configured for SRIO accesses. The property should + not exist on devices that do not support PAMU. + + The LIODN value is associated with all RMU transactions + (msg-unit, doorbell, port-write). + +Sub-Nodes for RMU: The RMU node is composed of multiple sub-nodes that +correspond to the actual sub-controllers in the RMU. The manual for a given +SoC will detail which and how many of these sub-controllers are implemented. + +Message Unit: + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,srio-msg-unit-vX.Y", "fsl,srio-msg-unit". + + The version X.Y should match the general SRIO controller's IP Block + revision register's Major(X) and Minor (Y) value. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers for message units + and doorbell units. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this device. The + value of the interrupts property consists of one interrupt + specifier. The format of the specifier is defined by the + binding document describing the node's interrupt parent. + + A pair of IRQs are specified in this property. The first + element is associated with the transmit (TX) interrupt and the + second element is associated with the receive (RX) interrupt. + +Doorbell Unit: + + - compatible + Usage: required + Value type: <string> + Definition: Must include: + "fsl,srio-dbell-unit-vX.Y", "fsl,srio-dbell-unit" + + The version X.Y should match the general SRIO controller's IP Block + revision register's Major(X) and Minor (Y) value. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers for message units + and doorbell units. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this device. The + value of the interrupts property consists of one interrupt + specifier. The format of the specifier is defined by the + binding document describing the node's interrupt parent. + + A pair of IRQs are specified in this property. The first + element is associated with the transmit (TX) interrupt and the + second element is associated with the receive (RX) interrupt. + +Port-Write Unit: + + - compatible + Usage: required + Value type: <string> + Definition: Must include: + "fsl,srio-port-write-unit-vX.Y", "fsl,srio-port-write-unit" + + The version X.Y should match the general SRIO controller's IP Block + revision register's Major(X) and Minor (Y) value. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers for message units + and doorbell units. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this device. The + value of the interrupts property consists of one interrupt + specifier. The format of the specifier is defined by the + binding document describing the node's interrupt parent. + + A single IRQ that handles port-write conditions is + specified by this property. (Typically shared with error). + + Note: All other standard properties (see the ePAPR) are allowed + but are optional. + +Example: + rmu: rmu@d3000 { + compatible = "fsl,srio-rmu"; + reg = <0xd3000 0x400>; + ranges = <0x0 0xd3000 0x400>; + fsl,liodn = <0xc8>; + + message-unit@0 { + compatible = "fsl,srio-msg-unit"; + reg = <0x0 0x100>; + interrupts = < + 60 2 0 0 /* msg1_tx_irq */ + 61 2 0 0>;/* msg1_rx_irq */ + }; + message-unit@100 { + compatible = "fsl,srio-msg-unit"; + reg = <0x100 0x100>; + interrupts = < + 62 2 0 0 /* msg2_tx_irq */ + 63 2 0 0>;/* msg2_rx_irq */ + }; + doorbell-unit@400 { + compatible = "fsl,srio-dbell-unit"; + reg = <0x400 0x80>; + interrupts = < + 56 2 0 0 /* bell_outb_irq */ + 57 2 0 0>;/* bell_inb_irq */ + }; + port-write-unit@4e0 { + compatible = "fsl,srio-port-write-unit"; + reg = <0x4e0 0x20>; + interrupts = <16 2 1 11>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt new file mode 100644 index 00000000..07abf0f2 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt @@ -0,0 +1,103 @@ +* Freescale Serial RapidIO (SRIO) Controller + +RapidIO port node: +Properties: + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,srio" for IP blocks with IP Block + Revision Register (SRIO IPBRR1) Major ID equal to 0x01c0. + + Optionally, a compatible string of "fsl,srio-vX.Y" where X is Major + version in IP Block Revision Register and Y is Minor version. If this + compatible is provided it should be ordered before "fsl,srio". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address and + length of the SRIO configuration registers. The size should + be set to 0x11000. + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this device. The + value of the interrupts property consists of one interrupt + specifier. The format of the specifier is defined by the + binding document describing the node's interrupt parent. + + A single IRQ that handles error conditions is specified by this + property. (Typically shared with port-write). + + - fsl,srio-rmu-handle: + Usage: required if rmu node is defined + Value type: <phandle> + Definition: A single <phandle> value that points to the RMU. + (See srio-rmu.txt for more details on RMU node binding) + +Port Child Nodes: There should a port child node for each port that exists in +the controller. The ports are numbered starting at one (1) and should have +the following properties: + + - cell-index + Usage: required + Value type: <u32> + Definition: A standard property. Matches the port id. + + - ranges + Usage: required if local access windows preset + Value type: <prop-encoded-array> + Definition: A standard property. Utilized to describe the memory mapped + IO space utilized by the controller. This corresponds to the + setting of the local access windows that are targeted to this + SRIO port. + + - fsl,liodn + Usage: optional-but-recommended (for devices with PAMU) + Value type: <prop-encoded-array> + Definition: The logical I/O device number for the PAMU (IOMMU) to be + correctly configured for SRIO accesses. The property should + not exist on devices that do not support PAMU. + + For HW (ie, the P4080) that only supports a LIODN for both + memory and maintenance transactions then a single LIODN is + represented in the property for both transactions. + + For HW (ie, the P304x/P5020, etc) that supports an LIODN for + memory transactions and a unique LIODN for maintenance + transactions then a pair of LIODNs are represented in the + property. Within the pair, the first element represents the + LIODN associated with memory transactions and the second element + represents the LIODN associated with maintenance transactions + for the port. + +Note: All other standard properties (see ePAPR) are allowed but are optional. + +Example: + + rapidio: rapidio@ffe0c0000 { + #address-cells = <2>; + #size-cells = <2>; + reg = <0xf 0xfe0c0000 0 0x11000>; + compatible = "fsl,srio"; + interrupts = <16 2 1 11>; /* err_irq */ + fsl,srio-rmu-handle = <&rmu>; + ranges; + + port1 { + cell-index = <1>; + #address-cells = <2>; + #size-cells = <2>; + fsl,liodn = <34>; + ranges = <0 0 0xc 0x20000000 0 0x10000000>; + }; + + port2 { + cell-index = <2>; + #address-cells = <2>; + #size-cells = <2>; + fsl,liodn = <48>; + ranges = <0 0 0xc 0x30000000 0 0x10000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt new file mode 100644 index 00000000..5ff76c9c --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt @@ -0,0 +1,73 @@ +Freescale Synchronous Serial Interface + +The SSI is a serial device that communicates with audio codecs. It can +be programmed in AC97, I2S, left-justified, or right-justified modes. + +Required properties: +- compatible: Compatible list, contains "fsl,ssi". +- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. +- reg: Offset and length of the register set for the device. +- interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and + level information for the interrupt. This should be + encoded based on the information in section 2) + depending on the type of interrupt controller you + have. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this device. +- fsl,mode: The operating mode for the SSI interface. + "i2s-slave" - I2S mode, SSI is clock slave + "i2s-master" - I2S mode, SSI is clock master + "lj-slave" - left-justified mode, SSI is clock slave + "lj-master" - l.j. mode, SSI is clock master + "rj-slave" - right-justified mode, SSI is clock slave + "rj-master" - r.j., SSI is clock master + "ac97-slave" - AC97 mode, SSI is clock slave + "ac97-master" - AC97 mode, SSI is clock master +- fsl,playback-dma: Phandle to a node for the DMA channel to use for + playback of audio. This is typically dictated by SOC + design. See the notes below. +- fsl,capture-dma: Phandle to a node for the DMA channel to use for + capture (recording) of audio. This is typically dictated + by SOC design. See the notes below. +- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. + This number is the maximum allowed value for SFCSR[TFWM0]. +- fsl,ssi-asynchronous: + If specified, the SSI is to be programmed in asynchronous + mode. In this mode, pins SRCK, STCK, SRFS, and STFS must + all be connected to valid signals. In synchronous mode, + SRCK and SRFS are ignored. Asynchronous mode allows + playback and capture to use different sample sizes and + sample rates. Some drivers may require that SRCK and STCK + be connected together, and SRFS and STFS be connected + together. This would still allow different sample sizes, + but not different sample rates. + +Optional properties: +- codec-handle: Phandle to a 'codec' node that defines an audio + codec connected to this SSI. This node is typically + a child of an I2C or other control node. + +Child 'codec' node required properties: +- compatible: Compatible list, contains the name of the codec + +Child 'codec' node optional properties: +- clock-frequency: The frequency of the input clock, which typically comes + from an on-board dedicated oscillator. + +Notes on fsl,playback-dma and fsl,capture-dma: + +On SOCs that have an SSI, specific DMA channels are hard-wired for playback +and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for +playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for +playback and DMA channel 3 for capture. The developer can choose which +DMA controller to use, but the channels themselves are hard-wired. The +purpose of these two properties is to represent this hardware design. + +The device tree nodes for the DMA channels that are referenced by +"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with +"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. +"fsl,mpc8610-dma-channel") can remain. If these nodes are left as +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA +drivers (fsldma) will attempt to use them, and it will conflict with the +sound drivers. diff --git a/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt b/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt new file mode 100644 index 00000000..b558585b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt @@ -0,0 +1,109 @@ + +Nintendo GameCube device tree +============================= + +1) The "flipper" node + + This node represents the multi-function "Flipper" chip, which packages + many of the devices found in the Nintendo GameCube. + + Required properties: + + - compatible : Should be "nintendo,flipper" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the interrupt controller within the "Flipper" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - compatible : should be "nintendo,flipper-pic" + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.c.i) The Auxiliary RAM (ARAM) node + + Represents the non cpu-addressable ram designed mainly to store audio + related information. + The ARAM node must be placed under the DSP node. + + Required properties: + + - compatible : should be "nintendo,flipper-aram" + - reg : should contain the ARAM start (zero-based) and length + +1.d) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,flipper-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.g) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + diff --git a/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt b/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt new file mode 100644 index 00000000..36afa322 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt @@ -0,0 +1,184 @@ + +Nintendo Wii device tree +======================== + +0) The root node + + This node represents the Nintendo Wii video game console. + + Required properties: + + - model : Should be "nintendo,wii" + - compatible : Should be "nintendo,wii" + +1) The "hollywood" node + + This node represents the multi-function "Hollywood" chip, which packages + many of the devices found in the Nintendo Wii. + + Required properties: + + - compatible : Should be "nintendo,hollywood" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,hollywood-vi","nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,hollywood-pi","nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the "Flipper" interrupt controller within the "Hollywood" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,flipper-pic" + - interrupt-controller + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,hollywood-dsp","nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.d) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-si","nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,hollywood-ai","nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-exi","nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + +1.g) The Open Host Controller Interface (OHCI) nodes + + Represent the USB 1.x Open Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ohci","usb-ohci" + - reg : should contain the OHCI registers location and length + - interrupts : should contain the OHCI interrupt + +1.h) The Enhanced Host Controller Interface (EHCI) node + + Represents the USB 2.0 Enhanced Host Controller Interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ehci","usb-ehci" + - reg : should contain the EHCI registers location and length + - interrupts : should contain the EHCI interrupt + +1.i) The Secure Digital Host Controller Interface (SDHCI) nodes + + Represent the Secure Digital Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-sdhci","sdhci" + - reg : should contain the SDHCI registers location and length + - interrupts : should contain the SDHCI interrupt + +1.j) The Inter-Processor Communication (IPC) node + + Represent the Inter-Processor Communication interface. This interface + enables communications between the Broadway and the Starlet processors. + + - compatible : should be "nintendo,hollywood-ipc" + - reg : should contain the IPC registers location and length + - interrupts : should contain the IPC interrupt + +1.k) The "Hollywood" interrupt controller node + + Represents the "Hollywood" interrupt controller within the + "Hollywood" chip. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,hollywood-pic" + - reg : should contain the controller registers location and length + - interrupt-controller + - interrupts : should contain the cascade interrupt of the "flipper" pic + - interrupt-parent: should contain the phandle of the "flipper" pic + +1.l) The General Purpose I/O (GPIO) controller node + + Represents the dual access 32 GPIO controller interface. + + Required properties: + + - #gpio-cells : <2> + - compatible : should be "nintendo,hollywood-gpio" + - reg : should contain the IPC registers location and length + - gpio-controller + +1.m) The control node + + Represents the control interface used to setup several miscellaneous + settings of the "Hollywood" chip like boot memory mappings, resets, + disk interface mode, etc. + + Required properties: + + - compatible : should be "nintendo,hollywood-control" + - reg : should contain the control registers location and length + +1.n) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,hollywood-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + |