| Age | Commit message (Collapse) | Author |
|---|
|
Add a board level property to the virt board which will
enable EL2 on the CPU if the user asks for it. The
default is not to provide EL2. If EL2 is enabled then
we will use SMC as our PSCI conduit, and report the
virtualization support in the GICv3 device tree node
and the ACPI tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-19-git-send-email-peter.maydell@linaro.org
|
|
Enable the ARM_FEATURE_EL2 bit on Cortex-A52 and
Cortex-A57, since this is all now sufficiently implemented
to work with the GICv3. We provide the usual CPU property
to disable it for backwards compatibility with the older
virt boards.
In this commit, we disable the EL2 feature on the
virt and ZynpMP boards, so there is no overall effect.
Another commit will expose a board-level property to
allow the user to enable EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-18-git-send-email-peter.maydell@linaro.org
|
|
The PSCI spec states that a CPU_ON call should cause the new
CPU to be started in the highest implemented Non-secure
exception level. We were incorrectly starting it at the
exception level of the caller, which happens to be correct
if EL2 is not implemented. Implement the correct logic
as described in the PSCI 1.0 spec section 6.4:
* if EL2 exists and SCR_EL3.HCE is set: start in EL2
* otherwise start in EL1
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Message-id: 1483977924-14522-17-git-send-email-peter.maydell@linaro.org
|
|
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-16-git-send-email-peter.maydell@linaro.org
[PMM: look at vms->psci_conduit rather than vms->virt
to decide whether to use HVC or SMC, and report no
PSCI support at all for the 'PSCI disabled' case]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
If we are giving the guest a CPU with EL2, it is likely to
want to use the HVC instruction itself, for instance for
providing PSCI to inner guest VMs. This makes using HVC
as the PSCI conduit for the outer QEMU a bad idea. We will
want to use SMC instead is this case: this makes sense
because QEMU's PSCI implementation is effectively an
emulation of functionality provided by EL3 firmware.
Add code to support selecting the PSCI conduit to use,
rather than hardcoding use of HVC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1483977924-14522-15-git-send-email-peter.maydell@linaro.org
|
|
Implement the architecturally required traps from NS EL1
to EL2 for the CPU interface registers. These fall into
several different groups:
* group-0-only registers all trap if ICH_HRC_EL2.TALL0 is set
(exactly the registers covered by gicv3_fiq_access())
* group-1-only registers all trap if ICH_HRC_EL2.TALL1 is set
(exactly the registers covered by gicv3_irq_access())
* DIR traps if ICH_HCR_EL2.TC or ICH_HCR_EL2.TDIR are set
* PMR, RPR, CTLR trap if ICH_HCR_EL2.TC is set
* SGI0R, SGI1R, ASGI1R trap if ICH_HCR_EL2.TC is set or
if HCR_EL2.IMO or HCR_EL2.FMO are set
We split DIR and the SGI registers out into their own access
functions, leaving the existing gicv3_irqfiq_access() just
handling PMR, RPR and CTLR.
This commit doesn't implement support for trapping on
HSTR_EL2.T12 for the 32-bit registers, as we don't implement
any of those per-coprocessor trap bits currently and
probably will want to do those in some more centralized way.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-14-git-send-email-peter.maydell@linaro.org
|
|
Implement the function which signals virtual interrupts to the
CPU as appropriate following CPU interface state changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-13-git-send-email-peter.maydell@linaro.org
|
|
Implement the two remaining ICV_ registers: EOIR and IAR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-12-git-send-email-peter.maydell@linaro.org
|
|
Implement the the ICV_ registers HPPIR, DIR and RPR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-11-git-send-email-peter.maydell@linaro.org
|
|
If the HCR_EL2.IMO or FMO bits are set, accesses to ICC_
system registers are redirected to be accesses to ICV_
registers (the guest-visible interface to the virtual
interrupt controller). Implement this behaviour for the
ICV_ registers which are simple accessors to the underlying
register state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-10-git-send-email-peter.maydell@linaro.org
|
|
The GICv3 virtualization interface includes system registers
accessible only to the hypervisor which form the control
interface for interrupt virtualization. Implement these
registers.
The function gicv3_cpuif_virt_update() which determines
whether it needs to signal vIRQ, vFIQ or a maintenance
interrupt is introduced here as a stub function -- its
implementation will be added in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-9-git-send-email-peter.maydell@linaro.org
|
|
As the first step in adding support for the virtualization
extensions to the GICv3 emulation:
* add the necessary data fields to the state structures
* add the fields to the migration state, as a subsection
which is only present if virtualization is enabled
The use of a subsection means we retain migration
compatibility as EL2 is not enabled on any CPUs currently.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-8-git-send-email-peter.maydell@linaro.org
|
|
Add defines to gicv3_internal.h for fields in the ICH_*
system registers which form the GIC virtualization control
interface.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-7-git-send-email-peter.maydell@linaro.org
|
|
Add fields to the ARMCPU structure to allow CPU classes to
specify the configurable aspects of their GIC CPU interface.
In particular, the virtualization support allows different
values for number of list registers, priority bits and
preemption bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-6-git-send-email-peter.maydell@linaro.org
|
|
Wire the new VIRQ, VFIQ and maintenance interrupt lines from the
GIC to each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-5-git-send-email-peter.maydell@linaro.org
|
|
The GICv3 support for virtualization includes an outbound
maintenance interrupt signal which is asserted when the
CPU interface wants to signal to the hypervisor that it
needs attention. Expose this as an outbound GPIO line from
the CPU object which can be wired up as a physical interrupt
line by the board code (as we do already for the CPU timers).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-4-git-send-email-peter.maydell@linaro.org
|
|
Augment the GIC's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
We never use these, but it's helpful to keep the v2-and-earlier
GIC's external interface in line with that of the GICv3 to
avoid board code having to add extra code conditional on which
version of the GIC is in use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-3-git-send-email-peter.maydell@linaro.org
|
|
Augment the GICv3's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-2-git-send-email-peter.maydell@linaro.org
|
|
Linux for arm64 v4.10 and later will complain if the ECAM config space is
not reserved in the ACPI namespace:
acpi PNP0A08:00: [Firmware Bug]: ECAM area [mem 0x3f000000-0x3fffffff] not reserved in ACPI namespace
The rationale is that OSes that don't consume the MCFG table should still
be able to infer that the PCI config space MMIO region is occupied.
So update the ACPI table generation routine to add this reservation.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1484328738-21149-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Using -cpu cortex-a9 (or any other unsupported CPU) with the virt
board will cause QEMU to segmentation fault. This bug was introduced
in commit 9ac4ef77, which incorrectly added a NULL terminator when
converting the VirtBoardInfo array into a simple array of strings
defining the valid CPUs. The cpuname_valid() loop already has
a termination condition based on ARRAY_SIZE, so the NULL is
spurious and causes the strcmp() to segfault if we reach it.
Delete the NULL.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1484619334-10488-1-git-send-email-zhaoshenglong@huawei.com
[PMM: expanded commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Create a ROM region, using the default size of the mapping window for
the CE0 FMC flash module, and fill it with the flash content.
This is a little hacky but until we can boot from a MMIO region, it
seems difficult to do anything else.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The Aspeed SMC controllers have a mode (Command mode) in which
accesses to the flash content are no different than doing MMIOs. The
controller generates all the necessary commands to load (or store)
data in memory.
So add a couple of tests doing direct reads and writes on the AHB bus.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-10-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Let's make sure when each test is run that the flash object is in an
initial state and did not keep configuration from the previous tests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1483979087-32663-9-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The Aspeed SMC controllers have a mode (Command mode) in which
accesses to the flash content are no different than doing MMIOs. The
controller generates all the necessary commands to load (or store)
data in memory.
However, accesses are restricted to the segment window assigned the
the flash module by the controller. This window is defined by the
Segment Address Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-8-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The SPI controller of the AST2400 SoC has less registers. So we can
adjust the size of the memory region holding the registers depending
on the controller type. We can also remove the guest_error logging
which is useless as the range of the region is strict enough.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1483979087-32663-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This is getting difficult to read. Also add a 'has_dma' field for each
controller type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-6-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
On the AST2500 SoC, the FMC controller flash type is fixed to SPI for
CE0 and CE1 and 4BYTE mode is autodetected for CE0.
On the AST2400 SoC, the FMC controller flash type and 4BYTE mode are
strapped with register SCU70. We use the default settings from the
palmetto-bmc machine for now.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Change the routines prototype to use a 'AspeedSMCFlash *' instead of
'AspeedSMCState *'. The result will help in making future changes
clearer.
Also change aspeed_smc_update_cs() which uselessly loops on all slave
devices to update their status.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Instead, we can simply set the irq level when unselecting the slave
devices. This change prepares ground for a subsequent cleanup of the
aspeed_smc_update_cs() routine which uselessly loops on all slaves to
update their status.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1483979087-32663-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This is useless as reset will be called later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Message-id: 1483979087-32663-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The DBGVCR_EL2 system register is needed to run a 32-bit
EL1 guest under a Linux EL2 64-bit hypervisor. Its only
purpose is to provide AArch64 with access to the state of
the DBGVCR AArch32 register. Since we only have a dummy
DBGVCR, implement a corresponding dummy DBGVCR32_EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
|
|
To run a VM in 32-bit EL1 our AArch32 interrupt handling code
needs to be able to cope with VIRQ and VFIQ exceptions.
These behave like IRQ and FIQ except that we don't need to try
to route them to Monitor mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
|
|
n25q00 and mt25q01 devices share the same JEDEC ID. The difference
between those two devices is number of dies and one bit in extended
JEDEC bytes. This commit adds proper entry for both devices by
introduction the number of dies and and new 25q00 entries.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-4-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Modern big flash NOR devices consist of more than one die.
Some of them do not support chip erase and instead have a die
erase command that can erase one die only. This commit adds
support for defining the number of dies in the chip, and adds
support for die erase command.
The NOR flash model is not strict, so no option to
disable chip erase has been added.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-3-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Some flash chips have additional page program opcode that
takes only 4 byte address. This commit adds support
for such command in Qemu.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-2-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The imx25 chip provides 3 i2c buses, but they have all been named
"i2c", which makes it difficult to predict which bus a device will
be connected to when specified on the command line.
This patch addresses the issue by naming the buses uniquely:
i2c-bus.0 i2c-bus.1 i2c-bus.2
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Message-id: 20170105043430.3176-2-alastair@au1.ibm.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
# gpg: Signature made Mon 16 Jan 2017 13:44:46 GMT
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request:
trace: Add event "guest_cpu_exit"
trace: Fix dynamic event state on vCPU hot-unplug
trace: Lock vCPU list when initializing dynamic tracing state
trace-events: spelling fix
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
QAPI patches for 2017-01-16
# gpg: Signature made Mon 16 Jan 2017 09:26:49 GMT
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2017-01-16: (180 commits)
build-sys: add qapi doc generation targets
build-sys: add txt documentation rules
build-sys: use a generic TEXI2MAN rule
build-sys: remove dvi doc generation
build-sys: use --no-split for info
docs: add qemu logo to pdf
qapi: add qapi2texi script
qmp-events: move 'MIGRATION_PASS' doc to schema
qmp-events: move 'DUMP_COMPLETED' doc to schema
qmp-events: move 'MEM_UNPLUG_ERROR' doc to schema
qmp-events: move 'VSERPORT_CHANGE' doc to schema
qmp-events: move 'QUORUM_REPORT_BAD' doc to schema
qmp-events: move 'QUORUM_FAILURE' doc to schema
qmp-events: move 'GUEST_PANICKED' doc to schema
qmp-events: move 'BALLOON_CHANGE' doc to schema
qmp-events: move 'ACPI_DEVICE_OST' doc to schema
qmp-events: move 'MIGRATION' doc to schema
qmp-events: move 'SPICE_MIGRATE_COMPLETED' doc to schema
qmp-events: move 'SPICE_DISCONNECTED' doc to schema
qmp-events: move 'SPICE_INITIALIZED' doc to schema
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
# gpg: Signature made Mon 16 Jan 2017 13:38:52 GMT
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/block-pull-request:
async: optimize aio_bh_poll
aio: document locking
aio-win32: remove walking_handlers, protecting AioHandler list with list_lock
aio-posix: remove walking_handlers, protecting AioHandler list with list_lock
aio: tweak walking in dispatch phase
aio-posix: split aio_dispatch_handlers out of aio_dispatch
qemu-thread: optimize QemuLockCnt with futexes on Linux
aio: make ctx->list_lock a QemuLockCnt, subsuming ctx->walking_bh
qemu-thread: introduce QemuLockCnt
aio: rename bh_lock to list_lock
block: get rid of bdrv_io_unplugged_begin/end
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
'remotes/stsquad/tags/pull-tcg-common-tlb-reset-20170113-r1' into staging
This is the same as the v3 posted except a re-base and a few extra signoffs
# gpg: Signature made Fri 13 Jan 2017 14:26:46 GMT
# gpg: using RSA key 0xFBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>"
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tcg-common-tlb-reset-20170113-r1:
cputlb: drop flush_global flag from tlb_flush
cpu_common_reset: wrap TCG specific code in tcg_enabled()
qom/cpu: move tlb_flush to cpu_common_reset
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signals the hot-unplugging of a virtual (guest) CPU.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-id: 148278748597.1404.10546320797997984932.stgit@fimbulvetr.bsc.es
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
We need to disable per-vCPU events on a vCPU that is hot-unplugged to
keep the dynamic event state global counters consistent.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-id: 148278748055.1404.1570530281528619895.stgit@fimbulvetr.bsc.es
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Fixes potential corruption when a vCPU is hot-(un)plugged while
initializing the current one.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-id: 148278747515.1404.6538173443841279200.stgit@fimbulvetr.bsc.es
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20161212221759.28949-1-marcandre.lureau@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Avoid entering the slow path of qemu_lockcnt_dec_and_lock if
no bottom half has to be deleted.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170112180800.21085-11-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170112180800.21085-10-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170112180800.21085-9-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170112180800.21085-8-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Preparing for the following patch, use QLIST_FOREACH_SAFE and
modify the placement of walking_handlers increment/decrement.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170112180800.21085-7-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
This simplifies the handling of dispatch_fds.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170112180800.21085-6-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
