# SPDX-License-Identifier: GPL-2.0-only # # Freescale device configuration # config NET_VENDOR_FREESCALE bool "Freescale devices" default y depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ M523x || M527x || M5272 || M528x || M520x || M532x || \ ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \ ARCH_LAYERSCAPE || COMPILE_TEST help If you have a network (Ethernet) card belonging to this class, say Y. Note that the answer to this question doesn't directly affect the kernel: saying N will just cause the configurator to skip all the questions about Freescale devices. If you say Y, you will be asked for your specific card in the following questions. if NET_VENDOR_FREESCALE config FEC tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ ARCH_MXC || SOC_IMX28 || COMPILE_TEST) default ARCH_MXC || SOC_IMX28 if ARM select CRC32 select NET_SELFTESTS select PHYLIB imply PTP_1588_CLOCK help Say Y here if you want to use the built-in 10/100 Fast ethernet controller on some Motorola ColdFire and Freescale i.MX processors. config FEC_MPC52xx tristate "FEC MPC52xx driver" depends on PPC_MPC52xx && PPC_BESTCOMM select CRC32 select PHYLIB select PPC_BESTCOMM_FEC help This option enables support for the MPC5200's on-chip Fast Ethernet Controller If compiled as module, it will be called fec_mpc52xx. config FEC_MPC52xx_MDIO bool "FEC MPC52xx MDIO bus driver" depends on FEC_MPC52xx default y help The MPC5200's FEC can connect to the Ethernet either with an external MII PHY chip or 10 Mbps 7-wire interface (Motorola? industry standard). If your board uses an external PHY connected to FEC, enable this. If not sure, enable. If compiled as module, it will be called fec_mpc52xx_phy. source "drivers/net/ethernet/freescale/fs_enet/Kconfig" source "drivers/net/ethernet/freescale/fman/Kconfig" config FSL_PQ_MDIO tristate "Freescale PQ MDIO" select PHYLIB help This driver supports the MDIO bus used by the gianfar and UCC drivers. config FSL_XGMAC_MDIO tristate "Freescale XGMAC MDIO" select PHYLIB depends on OF select OF_MDIO help This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and on the FMan mEMAC (which supports both Clauses 22 and 45) config UCC_GETH tristate "Freescale QE Gigabit Ethernet" depends on QUICC_ENGINE && PPC32 select FSL_PQ_MDIO select PHYLIB select FIXED_PHY help This driver supports the Gigabit Ethernet mode of the QUICC Engine, which is available on some Freescale SOCs. config UGETH_TX_ON_DEMAND bool "Transmit on Demand support" depends on UCC_GETH config GIANFAR tristate "Gianfar Ethernet" depends on HAS_DMA select FSL_PQ_MDIO select PHYLIB select FIXED_PHY select CRC32 help This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, and MPC86xx family of chips, the eTSEC on LS1021A and the FEC on the 8540. source "drivers/net/ethernet/freescale/dpaa/Kconfig" source "drivers/net/ethernet/freescale/dpaa2/Kconfig" source "drivers/net/ethernet/freescale/enetc/Kconfig" endif # NET_VENDOR_FREESCALE