config AMIGA bool depends on APUS default y help This option enables support for the Amiga series of computers. config ZORRO bool depends on APUS default y help This enables support for the Zorro bus in the Amiga. If you have expansion cards in your Amiga that conform to the Amiga AutoConfig(tm) specification, say Y, otherwise N. Note that even expansion cards that do not fit in the Zorro slots but fit in e.g. the CPU slot may fall in this category, so you have to say Y to let Linux use these. config ABSTRACT_CONSOLE bool depends on APUS default y config APUS_FAST_EXCEPT bool depends on APUS default y config AMIGA_PCMCIA bool "Amiga 1200/600 PCMCIA support" depends on APUS && EXPERIMENTAL help Include support in the kernel for pcmcia on Amiga 1200 and Amiga 600. If you intend to use pcmcia cards say Y; otherwise say N. config AMIGA_BUILTIN_SERIAL tristate "Amiga builtin serial support" depends on APUS help If you want to use your Amiga's built-in serial port in Linux, answer Y. To compile this driver as a module, choose M here. config GVPIOEXT tristate "GVP IO-Extender support" depends on APUS help If you want to use a GVP IO-Extender serial card in Linux, say Y. Otherwise, say N. config GVPIOEXT_LP tristate "GVP IO-Extender parallel printer support" depends on GVPIOEXT help Say Y to enable driving a printer from the parallel port on your GVP IO-Extender card, N otherwise. config GVPIOEXT_PLIP tristate "GVP IO-Extender PLIP support" depends on GVPIOEXT help Say Y to enable doing IP over the parallel port on your GVP IO-Extender card, N otherwise. config MULTIFACE_III_TTY tristate "Multiface Card III serial support" depends on APUS help If you want to use a Multiface III card's serial port in Linux, answer Y. To compile this driver as a module, choose M here. config A2232 tristate "Commodore A2232 serial support (EXPERIMENTAL)" depends on EXPERIMENTAL && APUS ---help--- This option supports the 2232 7-port serial card shipped with the Amiga 2000 and other Zorro-bus machines, dating from 1989. At a max of 19,200 bps, the ports are served by a 6551 ACIA UART chip each, plus a 8520 CIA, and a master 6502 CPU and buffer as well. The ports were connected with 8 pin DIN connectors on the card bracket, for which 8 pin to DB25 adapters were supplied. The card also had jumpers internally to toggle various pinning configurations. This driver can be built as a module; but then "generic_serial" will also be built as a module. This has to be loaded before "ser_a2232". If you want to do this, answer M here. config WHIPPET_SERIAL tristate "Hisoft Whippet PCMCIA serial support" depends on AMIGA_PCMCIA help HiSoft has a web page at , but there is no listing for the Whippet in their Amiga section. config APNE tristate "PCMCIA NE2000 support" depends on AMIGA_PCMCIA help If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, say N. To compile this driver as a module, choose M here: the module will be called apne. config SERIAL_CONSOLE bool "Support for serial port console" depends on APUS && (AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y) config HEARTBEAT bool "Use power LED as a heartbeat" depends on APUS help Use the power-on LED on your machine as a load meter. The exact behavior is platform-dependent, but normally the flash frequency is a hyperbolic function of the 5-minute load average. config PROC_HARDWARE bool "/proc/hardware support" depends on APUS source "drivers/zorro/Kconfig" config PCI_PERMEDIA bool "PCI for Permedia2" depends on !4xx && !8xx && APUS