| Age | Commit message (Collapse) | Author |
|---|
|
Add PM and runtime PM support to STM32 DFSDM drivers:
- stm32-dfsdm-core: manage clocks.
- stm32-dfsdm-adc: restore channels configuration upon resume. Also stop
restart everything in case of buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The sample frequency is driven using the oversampling ratio depending
on the SPI bus frequency.
Currently, oversampling ratio is computed by an entire division:
- spi_freq / sample_freq. This may result in inaccurate value.
Using DIV_ROUND_CLOSEST improves resulting sample frequency, which is
useful for audio that requests fixed rates (such as: 8, 16 or 32 kHz).
BTW, introduce new routine to re-factor sample frequency setting, and
move frequency accuracy message from warning to debug level.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch adds support for Maxim MAX31856 thermocouple
temperature sensor support.
More information can be found in:
https://www.maximintegrated.com/en/ds/MAX31856.pdf
NOTE: Driver support only Comparator Mode.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace diff_{m1,m2} with div_{m1,m2} since they are dividers and not a
differential settings.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add of_match_table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The VCNL4040 is almost identical to the VCNL4200 as far as register
layout goes but just need to check a different ID register location.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add an of_match table for devicetree probing.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The VCNL4200 datasheet says that word read and writes should be used
to access the registers.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Tested-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Claim direct mode to ensure no buffer mode is in use for:
- single conversion
- sample rate setting (must be set when filter isn't enabled).
- oversampling ratio (must be set when filter isn't enabled).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
DFSDM conversions can be launched continuously, or using various
triggers:
- by software
- hardware triggers (e.g. like in stm32-adc: TIM, LPTIM, EXTI)
- synchronously with DFSDM filter 0. e.g. for filters 1, 2
Launching conversions can be done using two methods:
a - injected:
- scan mode can be used to convert several channels each time a
trigger occurs.
- When not is scan mode, channels are converted in sequence, one upon
each trigger.
b - regular:
- supports software triggers or synchronous with filter 0
- single or continuous conversions
This patch finalizes DFSDM operating modes using IIO buffer modes:
- INDIO_BUFFER_SOFTWARE: regular continuous conversions (no trigger)
but limited to 1 channel. Users must set sampling frequency in this case.
For filters > 1, conversions can be started synchronously with filter 0.
- INDIO_BUFFER_TRIGGERED: triggered conversions uses injected mode for
launching conversions. DFSDM can use hardware triggers (e.g. STM32 timer
or lptimer), so add INDIO_HARDWARE_TRIGGERED to supported modes.
- INDIO_DIRECT_MODE: Only support DMA-based buffer modes. In case no DMA is
available, only support single conversions.
From userland perspective, to summarize various use cases:
1 - single conversion on any filter:
$ cd iio:deviceX
$ cat in_voltageY_raw
This uses regular a conversion (not continuous)
2 - Using sampling frequency without trigger (single channel, buffer)
$ cd iio:deviceX
$ echo 100 > sampling_frequency
$ echo "" > trigger/current_trigger
$ echo 1 > scan_elements/in_voltageY_en
$ echo 1 > buffer/enable
This uses regular conversion in continuous mode (Frequency is achieved
by tuning filter parameters)
3 - sync mode with filter 0: other filters can be converted when using
"st,filter0-sync" dt property. The conversions will get started at the
same time as filter 0. So for any filters > 1:
$ cd iio:deviceX
$ echo 100 > sampling_frequency
$ echo "" > trigger/current_trigger
$ echo 1 > scan_elements/in_voltageY_en
$ echo 1 > buffer/enable
Then start filter 0 as in 2 above.
4 - Using a hardware trigger (with one channel):
- check trigger, configure it:
$ cat /sys/bus/iio/devices/trigger1/name
tim6_trgo
$ echo 100 > /sys/bus/iio/devices/trigger1/sampling_frequency
- go to any filter:
$ echo 1 > scan_elements/in_voltageY_en
$ echo tim6_trgo > trigger/current_trigger
$ echo 1 > buffer/enable
This uses injected conversion as it uses a hardware trigger (without scan)
5 - Using a hardware trigger (with 2+ channel):
Same as in 4/ above, but enable two or more channels in scan_elements.
This uses injected conversion as it uses a hardware trigger (with scan mode)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In order to support multiple channels in buffer mode, add support for scan
mode. This is precursor patch to ease support of triggered buffer mode.
Currently, only audio uses buffer mode: Regular continuous conversions
with a single channel (per filter).
DFSDM hardware supports scan mode (only) with injected conversions.
Conversions can be launched by software (JSWSTART), trigger or
synchronously with filter 0 (e.g. JSYNC). Continuous conversion mode isn't
available for injected.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Optionally enable IIO hw consumer, when provided (e.g. for DFSDM_IIO type).
This is precursor patch to introduce buffer modes.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move DMA slave configuration to start routine: depending on regular or
injected mode is in use, DMA needs to read resp. RDATAR or JDATAR.
This is precursor patch to introduce injected mode (used for scan).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move DMA enable (e.g. set RDMAEN bit) away from start_conv() that is used
for both buffer and single conversions. Thus, single conv rely on
interrupt, not dma.
Note: take care to prepare all DMA stuff and set RDMAEN before starting
filter (can be set only when DFEN=0).
This is precursor patch to ease support of triggered buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
DFSDM regular continuous mode usage depends on current mode (not DMA):
- for single conversion, RCONT doesn't need to be set.
- for buffer mode, RCONT has to be set (e.g. INDIO_BUFFER_SOFTWARE
used by audio currently).
This is related to filter configuration, move it to relevant routine.
This is precursor patch to ease support of triggered buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Current ckout divider may be set to a value that makes ckout to exceed
spi-max-frequency. Rather use lower value (e.g. round up divider when
ckout isn't accurate).
Also when the SPI clock isn't accurate, 'spi_master_freq' is filled in
with expected frequency. Use computed value instead to be more accurate:
- e.g. source clock / (CKOUTDIV + 1)
Enforce checks on the divider: ckoutdiv range can be from 1-255 to provide
divider of 2-256.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
- Fix CHECK Macro argument 'wordsize' may be better as '(wordsize)' to avoid precedence issues
Slightly modified by Jonathan to take into account the staging graduation
and a copy and paste version of the same item on the following line.
Signed-off-by: Vladimir Petrigo <vladimir.petrigo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Final part of the re-organization. Move the `adis16400.h` into
`adis16400.c` since it no longer needs to be shared among other files.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change does a simple 1-to-1 rename of the adis16400_core.c file. Now
that the `adis16400_buffer.c` file was removed, everything can be moved
into a single driver file.
But first, this rename.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change has been done separately, so that it's easier to visualize the
changed logic in the adis_scan_update() function.
Most of the function in this `adis16400_update_scan_mode()` that deals with
burst-mode will be re-used in the ADIS16480, but with different parameters.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Some variants in the ADIS16400 family support burst mode. This mechanism is
implemented in the `adis16400_buffer.c` file.
Some variants in ADIS16480 are also adding burst mode, which is
functionally similar to ADIS16400, but with different parameters. To get
there, a `adis_burst` struct is added to parametrize certain bits of the
SPI communication to setup: the register that triggers burst-mode, and the
extra-data-length that needs be accounted for when building the bust-length
buffer.
The trigger handler cannot be made generic, since it's very specific to
each ADIS164XX family.
A future enhancement of this `adis_burst` mode will be the possibility to
enable/disable burst-mode. For the ADIS16400 family it's hard-coded to on
by default. But for ADIS16480 there will be a need to disable this.
When that will be implemented, both ADIS16400 & ADIS16480 will have the
burst-mode enable-able/disable-able.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The trigger handler for the ADIS16400 is very different from the generic
one in the ADIS library. Keeping it in a separate file won't make much
sense once the update_scan_mode function will be made more generic and
moved into the ADIS library.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add I2CXL-MaxSonar ultrasonic distance sensors of types mb1202, mb1212,
mb1222, mb1232, mb1242, mb7040, mb7137 using an i2c interface
Implemented functionality:
- reading the distance via in_distance_raw
- buffered mode with trigger
- make use of interrupt to announce completion of ranging
Add mb1232 driver to Kconfig and Makefile
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
devm_regmap_init_i2c may fail and return NULL. The fix returns
the error when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move ad7780 ADC driver out of staging and into the mainline.
The ad7780 is a sigma-delta analog to digital converter. This driver provides
reading voltage values and status bits from both the ad778x and ad717x series.
Its interface also allows writing on the FILTER and GAIN GPIO pins on the
ad778x.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Co-developed-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Until now this driver only exposed the raw value of the channels. With
this patch, the scale value is also exposed.
It depends of a regulator supply, and unlike most of the other driver, do
not having this regulator won't prevent to use the driver. The reason for
it is to allow to continue to use this driver with an old device tree. If
there is no regulator supply then the scale won't be exposed.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
A few headers is useless: remove them.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Sort the headers in alphabetic order in order to ease the maintenance for
this part.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support to STM LSM6DSOX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsox.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
A return statement is indented one level too deeply; clean this
up by removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management. Also fix MODULE_LICENSE for cros_ec_accel_legacy to match
the SPDX and boiler plate license.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Document cros_ec_sensors_read_lpc, adding an additional note to explain
that this is the safe function for reading the EC data.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The cros_ec sensors drivers do not call any sysfs functions
or use any sysfs defines, and thus do not need to include
linux/sysfs.h. Also, some cros_ec drivers include linux/delay.h
and is not used.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
[remove linux/delay.h]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The BMP280/BME280 calibration data should also go into the
entropy pool, like we do for BMP180.
This just adds the temperature and pressure calibration, the
humidity calibration seems like too much annoying calls to
add.
Cc: Tomasz Duszynski <tduszyns@gmail.com>
Cc: Stefan Tatschner <stefan.tatschner@gmail.com>
Cc: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Inertial sensor data collection and processing can be controlled by
configuring one of the DIOx lines as an external clock input. This
option is available for all devices supported by this driver. However,
only adis1649x devices support different modes for the external clock.
Sync mode is supported by all devices. In this mode, the output data
rate is equal with the clock frequency divided by DEC_RATE + 1. This
mode of calculation is similar with the case when the internal clock is
used.
Pulse Per Second (PPS) Mode, is only supported by adis1649x devices. In
this mode, the output data rate is equal to the product of the external
clock frequency and the scale factor in the SYNC_SCALE register.
This patch uses the "clock-names" property to enable the external clock
in one of the two supported modes: "sync" or "pps". This property is
optional. If it is not specified, the internal clock is used.
This patch also offers the option to select the DIOx line to be used as
an external clock input via the custom "adi,ext-clk-pin" property. If this
field is left empty, DIO2 is assigned as default external clock input pin.
Each DIOx pin supports only one function at a time (data ready line
selection or external clock input).
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
indio_dev->mlock is intended to protect state transitions in
the core. It's scope is tightly defined. For device specific
uses such as those made here, we should define a local lock
allowing the scope of the lock to be defined near to what it
is protecting.
These mlock changes can be non obvious, but given we don't do
anything other than direct for DACs, these ones are easy to do.
If anyone wants to help with this particular effort it would
be most welcome!
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Formatting of Kconfig files doesn't look so pretty, so just
take damp cloth and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
When building with -Wsometimes-uninitialized, Clang warns:
drivers/iio/adc/stmpe-adc.c:204:13: warning: variable 'data' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
Clang can't tell that data will never be used uninitialized because the
two if statements take care of all cases. Remove the first if statement
and make it the else branch of the second one so that it is apparent to
Clang that all cases are covered.
Link: https://github.com/ClangBuiltLinux/linux/issues/387
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: NIck Desaulniers <ndesaulniers@google.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
When building with -Wsometimes-uninitialized, Clang warns:
drivers/iio/common/ssp_sensors/ssp_iio.c:95:6: warning: variable
'calculated_time' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
While it isn't wrong, this will never be a problem because
iio_push_to_buffers_with_timestamp only uses calculated_time
on the same condition that it is assigned (when scan_timestamp
is not zero). While iio_push_to_buffers_with_timestamp is marked
as inline, Clang does inlining in the optimization stage, which
happens after the semantic analysis phase (plus inline is merely
a hint to the compiler).
Fix this by just zero initializing calculated_time.
Link: https://github.com/ClangBuiltLinux/linux/issues/394
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This driver's probe() uses a mix of devm_ and non-devm_ functions. This
means that the remove order will not be the exact opposite of the probe
order.
Remove order:
1. remove() executes:
iio_device_unregister
iio_triggered_buffer_cleanup
iio_trigger_unregister
(A)
2. core frees devm resources in reverse order:
free_irq
iio_trigger_free
iio_device_free
In (A) the trigger has been unregistered, but the irq handler is still
registered and active, so the trigger may still be touched via
interrupt -> as3935_event_work. This is a potential use-after-unregister.
Given that the delayed work is never canceled explicitly, it may run even
after iio_device_free. This is a potential use-after-free.
Solution: convert all probe functions to their devm_ equivalents.
Add a devm callback, called by the core on remove right after irq_free,
which explicitly cancels the delayed work. This will guarantee that all
resources are freed in the correct order.
As an added bonus, some boilerplate code can be removed.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Change dev_err message on line 215 in order to inform that
tia-gain-ohm is not defined and an external resistor is not
specified.
Signed-off-by: Anderson Reis <andersonreisrosa@gmail.com>
Signed-off-by: Lucas Oshiro <lucasseikioshiro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Invert if statement arms in line 214, in order to make the code cleaner,
solve these checkpatch.pl CHECKs:
- lmp9100.c:214: CHECK: braces {} should be used on all arms of this statement
- lmp9100.c:216: CHECK: Unbalanced braces around else statement
Signed-off-by: Lucas Oshiro <lucasseikioshiro@gmail.com>
Signed-off-by: Anderson Reis <andersonreisrosa@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Break the line 258 in order fit the line width on 80 characters. Remove
the blank line 279, as the line before is also a blank line. Solve these
checkpath.el WARNING and CHECK:
- lmp91000.c:258: WARNING: line over 80 characters
- lmp91000.c:279: CHECK: Please don't use multiple blank lines
Signed-off-by: Lucas Oshiro <lucasseikioshiro@gmail.com>
Signed-off-by: Anderson Reis <andersonreisrosa@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove unnecessary parentheses on line 116.
Signed-off-by: Lucas Oshiro <lucasseikioshiro@gmail.com>
Signed-off-by: Anderson Reis <andersonreisrosa@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ADS79XX has GPIO pins that can be used. Add support for the GPIO
pins using the GPIO chip framework.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
devm_iio_trigger_alloc may fail and return NULL. The fix returns
ENOMEM when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Update the module author to the current email address
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Update the module author to the current email address.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add device tree support for kxcjk-1013 accelerometer sensors.
Signed-off-by: Robert Yang <decatf@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add the SAR ADC driver for the Amlogic Meson-G12A SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
