| Age | Commit message (Collapse) | Author |
|---|
|
Introduce an alternate mode of operation where dm-integrity uses a
bitmap instead of a journal. If a bit in the bitmap is 1, the
corresponding region's data and integrity tags are not synchronized - if
the machine crashes, the unsynchronized regions will be recalculated.
The bitmap mode is faster than the journal mode, because we don't have
to write the data twice, but it is also less reliable, because if data
corruption happens when the machine crashes, it may not be detected.
Benchmark results for an SSD connected to a SATA300 port, when doing
large linear writes with dd:
buffered I/O:
raw device throughput - 245MB/s
dm-integrity with journaling - 120MB/s
dm-integrity with bitmap - 238MB/s
direct I/O with 1MB block size:
raw device throughput - 248MB/s
dm-integrity with journaling - 123MB/s
dm-integrity with bitmap - 223MB/s
For more info see dm-integrity in Documentation/device-mapper/
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Update documentation with the "meta_device" parameter and flags.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Add the dm-dust target, which simulates the behavior of bad sectors
at arbitrary locations, and the ability to enable the emulation of
the read failures at an arbitrary time.
This target behaves similarly to a linear target. At a given time,
the user can send a message to the target to start failing read
requests on specific blocks. When the failure behavior is enabled,
reads of blocks configured "bad" will fail with EIO.
Writes of blocks configured "bad" will result in the following:
1. Remove the block from the "bad block list".
2. Successfully complete the write.
After this point, the block will successfully contain the written
data, and will service reads and writes normally. This emulates the
behavior of a "remapped sector" on a hard disk drive.
dm-dust provides logging of which blocks have been added or removed
to the "bad block list", as well as logging when a block has been
removed from the bad block list. These messages can be used
alongside the messages from the driver using a dm-dust device to
analyze the driver's behavior when a read fails at a given time.
(This logging can be reduced via a "quiet" mode, if desired.)
NOTE: If the block size is larger than 512 bytes, only the first sector
of each "dust block" is detected. Placing a limiting layer above a dust
target, to limit the minimum I/O size to the dust block size, will
ensure proper emulation of the given large block size.
Signed-off-by: Bryan Gurney <bgurney@redhat.com>
Co-developed-by: Joe Shimkus <jshimkus@redhat.com>
Co-developed-by: John Dorminy <jdorminy@redhat.com>
Co-developed-by: John Pittman <jpittman@redhat.com>
Co-developed-by: Thomas Jaskiewicz <tjaskiew@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes from the last few weeks. Most of them are
smaller tweaks and fixes to DT and hardware descriptions for boards.
Some of the more significant ones are:
- eMMC and RGMII stability tweaks for rk3288
- DDC fixes for Rock PI 4
- Audio fixes for two TI am335x eval boards
- D_CAN clock fix for am335x
- Compilation fixes for clang
- !HOTPLUG_CPU compilation fix for one of the new platforms this
release (milbeaut)
- A revert of a gpio fix for nomadik that instead was fixed in the
gpio subsystem
- Whitespace fix for the DT JSON schema (no tabs allowed)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
ARM: milbeaut: fix build with !CONFIG_HOTPLUG_CPU
ARM: iop: don't use using 64-bit DMA masks
ARM: orion: don't use using 64-bit DMA masks
Revert "ARM: dts: nomadik: Fix polarity of SPI CS"
dt-bindings: cpu: Fix JSON schema
arm/mach-at91/pm : fix possible object reference leak
ARM: dts: at91: Fix typo in ISC_D0 on PC9
ARM: dts: Fix dcan clkctrl clock for am3
reset: meson-audio-arb: Fix missing .owner setting of reset_controller_dev
dt-bindings: reset: meson-g12a: Add missing USB2 PHY resets
ARM: dts: rockchip: Remove #address/#size-cells from rk3288-veyron gpio-keys
ARM: dts: rockchip: Remove #address/#size-cells from rk3288 mipi_dsi
ARM: dts: rockchip: Fix gpu opp node names for rk3288
ARM: dts: am335x-evmsk: Correct the regulators for the audio codec
ARM: dts: am335x-evm: Correct the regulators for the audio codec
ARM: OMAP2+: add missing of_node_put after of_device_is_available
ARM: OMAP1: ams-delta: Fix broken GPIO ID allocation
arm64: dts: stratix10: add the sysmgr-syscon property from the gmac's
arm64: dts: rockchip: fix rk3328 sdmmc0 write errors
arm64: dts: rockchip: fix rk3328 rgmii high tx error rate
...
|
|
Commit fd73403a4862 ("dt-bindings: arm: Add SMP enable-method for
Milbeaut") added support for a new cpu enable-method, but did so using
tabulations to ident. This is however invalid in the syntax, and resulted
in a failure when trying to use that schemas for validation.
Use spaces instead of tabs to indent to fix this.
Fixes: fd73403a4862 ("dt-bindings: arm: Add SMP enable-method for Milbeaut")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The output of the PSI files show a bunch of numbers with no unit. The
psi.txt documentation file also does not indicate what units are used.
One can only find out by looking at the source code. The units are
percentage for the averages and useconds for the total. Make the
information easier to find by documenting the units in psi.txt.
Link: http://lkml.kernel.org/r/20190402193810.3450-1-longman@redhat.com
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For very short input data (0 - 1 bytes), lzo-rle was not behaving
correctly. Fix this behaviour and update documentation accordingly.
For zero-length input, lzo v0 outputs an end-of-stream marker only,
which was misinterpreted by lzo-rle as a bitstream version number.
Ensure bitstream versions > 0 require a minimum stream length of 5.
Also fixes a bug in handling the tail for very short inputs when a
bitstream version is present.
Link: http://lkml.kernel.org/r/20190326165857.34613-1-dave.rodgman@arm.com
Signed-off-by: Dave Rodgman <dave.rodgman@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
1) Several hash table refcount fixes in batman-adv, from Sven
Eckelmann.
2) Use after free in bpf_evict_inode(), from Daniel Borkmann.
3) Fix mdio bus registration in ixgbe, from Ivan Vecera.
4) Unbounded loop in __skb_try_recv_datagram(), from Paolo Abeni.
5) ila rhashtable corruption fix from Herbert Xu.
6) Don't allow upper-devices to be added to vrf devices, from Sabrina
Dubroca.
7) Add qmi_wwan device ID for Olicard 600, from Bjørn Mork.
8) Don't leave skb->next poisoned in __netif_receive_skb_list_ptype,
from Alexander Lobakin.
9) Missing IDR checks in mlx5 driver, from Aditya Pakki.
10) Fix false connection termination in ktls, from Jakub Kicinski.
11) Work around some ASPM issues with r8169 by disabling rx interrupt
coalescing on certain chips. From Heiner Kallweit.
12) Properly use per-cpu qstat values on NOLOCK qdiscs, from Paolo
Abeni.
13) Fully initialize sockaddr_in structures in SCTP, from Xin Long.
14) Various BPF flow dissector fixes from Stanislav Fomichev.
15) Divide by zero in act_sample, from Davide Caratti.
16) Fix bridging multicast regression introduced by rhashtable
conversion, from Nikolay Aleksandrov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
ibmvnic: Fix completion structure initialization
ipv6: sit: reset ip header pointer in ipip6_rcv
net: bridge: always clear mcast matching struct on reports and leaves
libcxgb: fix incorrect ppmax calculation
vlan: conditional inclusion of FCoE hooks to match netdevice.h and bnx2x
sch_cake: Make sure we can write the IP header before changing DSCP bits
sch_cake: Use tc_skb_protocol() helper for getting packet protocol
tcp: Ensure DCTCP reacts to losses
net/sched: act_sample: fix divide by zero in the traffic path
net: thunderx: fix NULL pointer dereference in nicvf_open/nicvf_stop
net: hns: Fix sparse: some warnings in HNS drivers
net: hns: Fix WARNING when remove HNS driver with SMMU enabled
net: hns: fix ICMP6 neighbor solicitation messages discard problem
net: hns: Fix probabilistic memory overwrite when HNS driver initialized
net: hns: Use NAPI_POLL_WEIGHT for hns driver
net: hns: fix KASAN: use-after-free in hns_nic_net_xmit_hw()
flow_dissector: rst'ify documentation
ipv6: Fix dangling pointer when ipv6 fragment
net-gro: Fix GRO flush when receiving a GSO packet.
flow_dissector: document BPF flow dissector environment
...
|
|
Rename bpf_flow_dissector.txt to bpf_flow_dissector.rst and fix
formatting. Also, link it from the Documentation/networking/index.rst.
Tested with 'make htmldocs' to make sure it looks reasonable.
Fixes: ae82899bbe92 ("flow_dissector: document BPF flow dissector environment")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Short doc on what BPF flow dissector should expect in the input
__sk_buff and flow_keys.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Couple of minor hwmon fixes"
* tag 'hwmon-for-v5.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
dt-bindings: hwmon: (adc128d818) Specify ti,mode property size
hwmon: (ntc_thermistor) Fix temperature type reporting
hwmon: (occ) Fix power sensor indexing
hwmon: (w83773g) Select REGMAP_I2C to fix build error
|
|
Pull KVM fixes from Paolo Bonzini:
"A collection of x86 and ARM bugfixes, and some improvements to
documentation.
On top of this, a cleanup of kvm_para.h headers, which were exported
by some architectures even though they not support KVM at all. This is
responsible for all the Kbuild changes in the diffstat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
Documentation: kvm: clarify KVM_SET_USER_MEMORY_REGION
KVM: doc: Document the life cycle of a VM and its resources
KVM: selftests: complete IO before migrating guest state
KVM: selftests: disable stack protector for all KVM tests
KVM: selftests: explicitly disable PIE for tests
KVM: selftests: assert on exit reason in CR4/cpuid sync test
KVM: x86: update %rip after emulating IO
x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
kvm: don't redefine flags as something else
kvm: mmu: Used range based flushing in slot_handle_level_range
KVM: export <linux/kvm_para.h> and <asm/kvm_para.h> iif KVM is supported
KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
kvm: nVMX: Add a vmentry check for HOST_SYSENTER_ESP and HOST_SYSENTER_EIP fields
KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
KVM: Reject device ioctls from processes other than the VM's creator
KVM: doc: Fix incorrect word ordering regarding supported use of APIs
KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 5.1-rc3.
Nothing major here, just a number of potential problems fixes for
error handling paths, as well as some other minor bugfixes for
reported issues with 5.1-rc1.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix NULL pointer issue when tty_port ops is not set
Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
dt-bindings: serial: Add compatible for Mediatek MT8183
tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
tty/serial: atmel: Add is_half_duplex helper
serial: sh-sci: Fix setting SCSCR_TIE while transferring data
serial: ar933x_uart: Fix build failure with disabled console
tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup
sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()
tty: mxs-auart: fix a potential NULL pointer dereference
tty: atmel_serial: fix a potential NULL pointer dereference
serial: max310x: Fix to avoid potential NULL pointer dereference
serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2019-03-29
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Bug fix in BTF deduplication that was mishandling an equivalence
comparison, from Andrii.
2) libbpf Makefile fixes to properly link against libelf for the shared
object and to actually export AF_XDP's xsk.h header, from Björn.
3) Fix use after free in bpf inode eviction, from Daniel.
4) Fix a bug in skb creation out of cpumap redirect, from Jesper.
5) Remove an unnecessary and triggerable WARN_ONCE() in max number
of call stack frames checking in verifier, from Paul.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A new ID for the i801 driver and some Documentation fixes to make it
easier for people to find the bindings (which is also a basis for
further improvements in that area)"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: wmt: make bindings file name match the driver
i2c: sun6i-p2wi: make bindings file name match the driver
i2c: stu300: make bindings file name match the driver
i2c: mt65xx: make bindings file name match the driver
i2c: iop3xx: make bindings file name match the driver
i2c: i801: Add support for Intel Comet Lake
|
|
By default, cells in DT are 32-bit in size. The driver reads "ti,mode"
using the function of_property_read_u8() which causes the value to be
read incorrectly in little-endian architectures if the size is not
specified.
Make it explicit in the binding documentation that this prorperty must
be set as a 8-bit value.
Signed-off-by: Carlos Menin <menin@carlosaurelio.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The documentation does not mention how to delete a slot, add the
information.
Reported-by: Nathaniel McCallum <npmccallum@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The series to add memcg accounting to KVM allocations[1] states:
There are many KVM kernel memory allocations which are tied to the
life of the VM process and should be charged to the VM process's
cgroup.
While it is correct to account KVM kernel allocations to the cgroup of
the process that created the VM, it's technically incorrect to state
that the KVM kernel memory allocations are tied to the life of the VM
process. This is because the VM itself, i.e. struct kvm, is not tied to
the life of the process which created it, rather it is tied to the life
of its associated file descriptor. In other words, kvm_destroy_vm() is
not invoked until fput() decrements its associated file's refcount to
zero. A simple example is to fork() in Qemu and have the child sleep
indefinitely; kvm_destroy_vm() isn't called until Qemu closes its file
descriptor *and* the rogue child is killed.
The allocations are guaranteed to be *accounted* to the process which
created the VM, but only because KVM's per-{VM,vCPU} ioctls reject the
ioctl() with -EIO if kvm->mm != current->mm. I.e. the child can keep
the VM "alive" but can't do anything useful with its reference.
Note that because 'struct kvm' also holds a reference to the mm_struct
of its owner, the above behavior also applies to userspace allocations.
Given that mucking with a VM's file descriptor can lead to subtle and
undesirable behavior, e.g. memcg charges persisting after a VM is shut
down, explicitly document a VM's lifecycle and its impact on the VM's
resources.
Alternatively, KVM could aggressively free resources when the creating
process exits, e.g. via mmu_notifier->release(). However, mmu_notifier
isn't guaranteed to be available, and freeing resources when the creator
exits is likely to be error prone and fragile as KVM would need to
ensure that it only freed resources that are truly out of reach. In
practice, the existing behavior shouldn't be problematic as a properly
configured system will prevent a child process from being moved out of
the appropriate cgroup hierarchy, i.e. prevent hiding the process from
the OOM killer, and will prevent an unprivileged user from being able to
to hold a reference to struct kvm via another method, e.g. debugfs.
[1]https://patchwork.kernel.org/patch/10806707/
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM's API requires thats ioctls must be issued from the same process
that created the VM. In other words, userspace can play games with a
VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the
creator can do anything useful. Explicitly reject device ioctls that
are issued by a process other than the VM's creator, and update KVM's
API documentation to extend its requirements to device ioctls.
Fixes: 852b6d57dc7f ("kvm: add device control API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Per Paolo[1], instantiating multiple VMs in a single process is legal;
but this conflicts with KVM's API documentation, which states:
The only supported use is one virtual machine per process, and one
vcpu per thread.
However, an earlier section in the documentation states:
Only run VM ioctls from the same process (address space) that was used
to create the VM.
and:
Only run vcpu ioctls from the same thread that was used to create the
vcpu.
This suggests that the conflicting documentation is simply an incorrect
ordering of of words, i.e. what's really meant is that a virtual machine
can't be shared across multiple processes and a vCPU can't be shared
across multiple threads.
Tweak the blurb on issuing ioctls to use a more assertive tone, and
rewrite the "supported use" sentence to reference said blurb instead of
poorly restating it in different terms.
Opportunistically add missing punctuation.
[1] https://lkml.kernel.org/r/f23265d4-528e-3bd4-011f-4d7b8f3281db@redhat.com
Fixes: 9c1b96e34717 ("KVM: Document basic API")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Improve notes on asynchronous ioctl]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The cr4_pae flag is a bit of a misnomer, its purpose is really to track
whether the guest PTE that is being shadowed is a 4-byte entry or an
8-byte entry. Prior to supporting nested EPT, the size of the gpte was
reflected purely by CR4.PAE. KVM fudged things a bit for direct sptes,
but it was mostly harmless since the size of the gpte never mattered.
Now that a spte may be tracking an indirect EPT entry, relying on
CR4.PAE is wrong and ill-named.
For direct shadow pages, force the gpte_size to '1' as they are always
8-byte entries; EPT entries can only be 8-bytes and KVM always uses
8-byte entries for NPT and its identity map (when running with EPT but
not unrestricted guest).
Likewise, nested EPT entries are always 8-bytes. Nested EPT presents a
unique scenario as the size of the entries are not dictated by CR4.PAE,
but neither is the shadow page a direct map. To handle this scenario,
set cr0_wp=1 and smap_andnot_wp=1, an otherwise impossible combination,
to denote a nested EPT shadow page. Use the information to avoid
incorrectly zapping an unsync'd indirect page in __kvm_sync_page().
Providing a consistent and accurate gpte_size fixes a bug reported by
Vitaly where fast_cr3_switch() always fails when switching from L2 to
L1 as kvm_mmu_get_page() would force role.cr4_pae=0 for direct pages,
whereas kvm_calc_mmu_role_common() would set it according to CR4.PAE.
Fixes: 7dcd575520082 ("x86/kvm/mmu: check if tdp/shadow MMU reconfiguration is needed")
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Update the mount API docs to reflect recent changes to the code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:
1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.
2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.
3) Fix documentation for some eBPF helpers, from Quentin Monnet.
4) Some UAPI bpf header sync with tools, also from Quentin Monnet.
5) Set descriptor ownership bit at the right time for jumbo frames in
stmmac driver, from Aaro Koskinen.
6) Set IFF_UP properly in tun driver, from Eric Dumazet.
7) Fix load/store doubleword instruction generation in powerpc eBPF
JIT, from Naveen N. Rao.
8) nla_nest_start() return value checks all over, from Kangjie Lu.
9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
merge window. From Marcelo Ricardo Leitner and Xin Long.
10) Fix memory corruption with large MTUs in stmmac, from Aaro
Koskinen.
11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
Dumazet.
12) Fix topology subscription cancellation in tipc, from Erik Hugne.
13) Memory leak in genetlink error path, from Yue Haibing.
14) Valid control actions properly in packet scheduler, from Davide
Caratti.
15) Even if we get EEXIST, we still need to rehash if a shrink was
delayed. From Herbert Xu.
16) Fix interrupt mask handling in interrupt handler of r8169, from
Heiner Kallweit.
17) Fix leak in ehea driver, from Wen Yang"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
dpaa2-eth: fix race condition with bql frame accounting
chelsio: use BUG() instead of BUG_ON(1)
net: devlink: skip info_get op call if it is not defined in dumpit
net: phy: bcm54xx: Encode link speed and activity into LEDs
tipc: change to check tipc_own_id to return in tipc_net_stop
net: usb: aqc111: Extend HWID table by QNAP device
net: sched: Kconfig: update reference link for PIE
net: dsa: qca8k: extend slave-bus implementations
net: dsa: qca8k: remove leftover phy accessors
dt-bindings: net: dsa: qca8k: support internal mdio-bus
dt-bindings: net: dsa: qca8k: fix example
net: phy: don't clear BMCR in genphy_soft_reset
bpf, libbpf: clarify bump in libbpf version info
bpf, libbpf: fix version info and add it to shared object
rxrpc: avoid clang -Wuninitialized warning
tipc: tipc clang warning
net: sched: fix cleanup NULL pointer exception in act_mirr
r8169: fix cable re-plugging issue
net: ethernet: ti: fix possible object reference leak
net: ibm: fix possible object reference leak
...
|
|
This adds dt-binding documentation of uart for Mediatek MT8183 SoC
Platform.
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Section 2.2.1 BTF_KIND_INT a bullet list was collapsed due to
text reflow in commit 9ab5305dbe3f ("docs/btf: reflow text to
fill up to 78 characters").
This patch correct the mistake. Also adjust next bullet list,
which is used for comparison, to get rendered the same way.
Fixes: 9ab5305dbe3f ("docs/btf: reflow text to fill up to 78 characters")
Link: https://www.kernel.org/doc/html/latest/bpf/btf.html#btf-kind-int
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch updates the qca8k's binding to document to the
approach for using the internal mdio-bus of the supported
qca8k switches.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the example, the phy at phy@0 is clashing with
the switch0@0 at the same address. Usually, the switches
are accessible through pseudo PHYs which in case of the
qca8k are located at 0x10 - 0x18.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree:
1) Remove a direct dependency with IPv6 introduced by the
sip_external_media feature, from Alin Nastac.
2) Fix bogus ENOENT when removing interval elements from set.
3) Set transport_header from br_netfilter to mimic the stack
behaviour, this partially fixes a checksum validation bug
from the SCTP connection tracking, from Xin Long.
4) Fix undefined reference to symbol in xt_TEE, due to missing
Kconfig dependencies, from Arnd Bergmann.
5) Check for NULL in skb_header_pointer() calls in ip6t_shr,
from Kangjie Lu.
6) Fix bogus EBUSY when removing an existing conntrack helper from
a transaction.
7) Fix module autoload of the redirect extension.
8) Remove duplicated transition in flowtable diagram in the existing
documentation.
9) Missing .release_ops call from error path in newrule() which
results module refcount leak, from Taehee Yoo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 5.1 from Marc Zyngier:
- irqsteer error handling fix
- GICv3 range coalescing fix
- stm32 coprocessor coexistence fixes
- mbigen MSI teardown fix
- non-DT secondary GIC infrastructure removed
- various cleanups (brcmstb-l2, mmp)
- new DT bindings (r8a774c0)
|
|
Document RZ/G2E (R8A774C0) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add PCI ID for Intel Comet Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
No direct transition from prerouting to forward hook, routing lookup
needs to happen first.
Fixes: 19b351f16fd9 ("netfilter: add flowtable documentation")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Provide an explanation of what is expected with respect to sending new
versions of specific patches within a patch series, as well as what
happens if an earlier patch series accidentally gets merged).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use https and link to the patch directly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix documentation markup warnings in snmp_counter.rst:
Documentation/networking/snmp_counter.rst:416: WARNING: Title underline too short.
Documentation/networking/snmp_counter.rst:684: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:693: WARNING: Title underline too short.
Documentation/networking/snmp_counter.rst:707: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:712: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:722: WARNING: Title underline too short.
Documentation/networking/snmp_counter.rst:733: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:736: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:739: WARNING: Bullet list ends without a blank line; unexpected unindent.
Fixes: 80cc49507ba48 ("net: Add part of TCP counts explanations in snmp_counters.rst")
Fixes: 8e2ea53a83dfb ("add snmp counters document")
Fixes: a6c7c7aac2de6 ("net: add document for several snmp counters")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: yupeng <yupeng0921@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- add more Build-Depends to Debian source package
- prefix header search paths with $(srctree)/
- make modpost show verbose section mismatch warnings
- avoid hard-coded CROSS_COMPILE for h8300
- fix regression for Debian make-kpkg command
- add semantic patch to detect missing put_device()
- fix some warnings of 'make deb-pkg'
- optimize NOSTDINC_FLAGS evaluation
- add warnings about redundant generic-y
- clean up Makefiles and scripts
* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: remove stale lxdialog/.gitignore
kbuild: force all architectures except um to include mandatory-y
kbuild: warn redundant generic-y
Revert "modsign: Abort modules_install when signing fails"
kbuild: Make NOSTDINC_FLAGS a simply expanded variable
kbuild: deb-pkg: avoid implicit effects
coccinelle: semantic code search for missing put_device()
kbuild: pkg: grep include/config/auto.conf instead of $KCONFIG_CONFIG
kbuild: deb-pkg: introduce is_enabled and if_enabled_echo to builddeb
kbuild: deb-pkg: add CONFIG_ prefix to kernel config options
kbuild: add workaround for Debian make-kpkg
kbuild: source include/config/auto.conf instead of ${KCONFIG_CONFIG}
unicore32: simplify linker script generation for decompressor
h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
kbuild: move archive command to scripts/Makefile.lib
modpost: always show verbose warning for section mismatch
ia64: prefix header search path with $(srctree)/
libfdt: prefix header search paths with $(srctree)/
deb-pkg: generate correct build dependencies
|
|
Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.
um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull device-dax updates from Dan Williams:
"New device-dax infrastructure to allow persistent memory and other
"reserved" / performance differentiated memories, to be assigned to
the core-mm as "System RAM".
Some users want to use persistent memory as additional volatile
memory. They are willing to cope with potential performance
differences, for example between DRAM and 3D Xpoint, and want to use
typical Linux memory management apis rather than a userspace memory
allocator layered over an mmap() of a dax file. The administration
model is to decide how much Persistent Memory (pmem) to use as System
RAM, create a device-dax-mode namespace of that size, and then assign
it to the core-mm. The rationale for device-dax is that it is a
generic memory-mapping driver that can be layered over any "special
purpose" memory, not just pmem. On subsequent boots udev rules can be
used to restore the memory assignment.
One implication of using pmem as RAM is that mlock() no longer keeps
data off persistent media. For this reason it is recommended to enable
NVDIMM Security (previously merged for 5.0) to encrypt pmem contents
at rest. We considered making this recommendation an actively enforced
requirement, but in the end decided to leave it as a distribution /
administrator policy to allow for emulation and test environments that
lack security capable NVDIMMs.
Summary:
- Replace the /sys/class/dax device model with /sys/bus/dax, and
include a compat driver so distributions can opt-in to the new ABI.
- Allow for an alternative driver for the device-dax address-range
- Introduce the 'kmem' driver to hotplug / assign a device-dax
address-range to the core-mm.
- Arrange for the device-dax target-node to be onlined so that the
newly added memory range can be uniquely referenced by numa apis"
NOTE! I'm not entirely happy with the whole "PMEM as RAM" model because
we currently have special - and very annoying rules in the kernel about
accessing PMEM only with the "MC safe" accessors, because machine checks
inside the regular repeat string copy functions can be fatal in some
(not described) circumstances.
And apparently the PMEM modules can cause that a lot more than regular
RAM. The argument is that this happens because PMEM doesn't necessarily
get scrubbed at boot like RAM does, but that is planned to be added for
the user space tooling.
Quoting Dan from another email:
"The exposure can be reduced in the volatile-RAM case by scanning for
and clearing errors before it is onlined as RAM. The userspace tooling
for that can be in place before v5.1-final. There's also runtime
notifications of errors via acpi_nfit_uc_error_notify() from
background scrubbers on the DIMM devices. With that mechanism the
kernel could proactively clear newly discovered poison in the volatile
case, but that would be additional development more suitable for v5.2.
I understand the concern, and the need to highlight this issue by
tapping the brakes on feature development, but I don't see PMEM as RAM
making the situation worse when the exposure is also there via DAX in
the PMEM case. Volatile-RAM is arguably a safer use case since it's
possible to repair pages where the persistent case needs active
application coordination"
* tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: "Hotplug" persistent memory for use like normal RAM
mm/resource: Let walk_system_ram_range() search child resources
mm/memory-hotplug: Allow memory resources to be children
mm/resource: Move HMM pr_debug() deeper into resource code
mm/resource: Return real error codes from walk failures
device-dax: Add a 'modalias' attribute to DAX 'bus' devices
device-dax: Add a 'target_node' attribute
device-dax: Auto-bind device after successful new_id
acpi/nfit, device-dax: Identify differentiated memory with a unique numa-node
device-dax: Add /sys/class/dax backwards compatibility
device-dax: Add support for a dax override driver
device-dax: Move resource pinning+mapping into the common driver
device-dax: Introduce bus + driver model
device-dax: Start defining a dax bus model
device-dax: Remove multi-resource infrastructure
device-dax: Kill dax_region base
device-dax: Kill dax_region ida
|
|
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
|
|
Pull more smb3 updates from Steve French:
"Various tracing and debugging improvements, crediting fixes, some
cleanup, and important fallocate fix (fixes three xfstests) and lock
fix.
Summary:
- Various additional dynamic tracing tracepoints
- Debugging improvements (including ability to query the server via
SMB3 fsctl from userspace tools which can help with stats and
debugging)
- One minor performance improvement (root directory inode caching)
- Crediting (SMB3 flow control) fixes
- Some cleanup (docs and to mknod)
- Important fixes: one to smb3 implementation of fallocate zero range
(which fixes three xfstests) and a POSIX lock fix"
* tag '5.1-rc-smb3' of git://git.samba.org/sfrench/cifs-2.6: (22 commits)
CIFS: fix POSIX lock leak and invalid ptr deref
SMB3: Allow SMB3 FSCTL queries to be sent to server from tools
cifs: fix incorrect handling of smb2_set_sparse() return in smb3_simple_falloc
smb2: fix typo in definition of a few error flags
CIFS: make mknod() an smb_version_op
cifs: minor documentation updates
cifs: remove unused value pointed out by Coverity
SMB3: passthru query info doesn't check for SMB3 FSCTL passthru
smb3: add dynamic tracepoints for simple fallocate and zero range
cifs: fix smb3_zero_range so it can expand the file-size when required
cifs: add SMB2_ioctl_init/free helpers to be used with compounding
smb3: Add dynamic trace points for various compounded smb3 ops
cifs: cache FILE_ALL_INFO for the shared root handle
smb3: display volume serial number for shares in /proc/fs/cifs/DebugData
cifs: simplify how we handle credits in compound_send_recv()
smb3: add dynamic tracepoint for timeout waiting for credits
smb3: display security information in /proc/fs/cifs/DebugData more accurately
cifs: add a timeout argument to wait_for_free_credits
cifs: prevent starvation in wait_for_free_credits for multi-credit requests
cifs: wait_for_free_credits() make it possible to wait for >=1 credits
...
|
|
Pull KVM updates from Paolo Bonzini:
"ARM:
- some cleanups
- direct physical timer assignment
- cache sanitization for 32-bit guests
s390:
- interrupt cleanup
- introduction of the Guest Information Block
- preparation for processor subfunctions in cpu models
PPC:
- bug fixes and improvements, especially related to machine checks
and protection keys
x86:
- many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations
- AVIC fixes
Generic:
- memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (147 commits)
kvm: vmx: fix formatting of a comment
KVM: doc: Document the life cycle of a VM and its resources
MAINTAINERS: Add KVM selftests to existing KVM entry
Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
KVM: PPC: Book3S: Add count cache flush parameters to kvmppc_get_cpu_char()
KVM: PPC: Fix compilation when KVM is not enabled
KVM: Minor cleanups for kvm_main.c
KVM: s390: add debug logging for cpu model subfunctions
KVM: s390: implement subfunction processor calls
arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
KVM: arm/arm64: Remove unused timer variable
KVM: PPC: Book3S: Improve KVM reference counting
KVM: PPC: Book3S HV: Fix build failure without IOMMU support
Revert "KVM: Eliminate extra function calls in kvm_get_dirty_log_protect()"
x86: kvmguest: use TSC clocksource if invariant TSC is exposed
KVM: Never start grow vCPU halt_poll_ns from value below halt_poll_ns_grow_start
KVM: Expose the initial start value in grow_halt_poll_ns() as a module parameter
KVM: grow_halt_poll_ns() should never shrink vCPU halt_poll_ns
KVM: x86/mmu: Consolidate kvm_mmu_zap_all() and kvm_mmu_zap_mmio_sptes()
KVM: x86/mmu: WARN if zapping a MMIO spte results in zapping children
...
|
|
Pull ARM updates from Russell King:
- An improvement from Ard Biesheuvel, who noted that the identity map
setup was taking a long time due to flush_cache_louis().
- Update a comment about dma_ops from Wolfram Sang.
- Remove use of "-p" with ld, where this flag has been a no-op since
2004.
- Remove the printing of the virtual memory layout, which is no longer
useful since we hide pointers.
- Correct SCU help text.
- Remove legacy TWD registration method.
- Add pgprot_device() implementation for mapping PCI sysfs resource
files.
- Initialise PFN limits earlier for kmemleak.
- Fix argument count to match macro definition (affects clang builds)
- Use unified assembler language almost everywhere for clang, and other
clang improvements (from Stefan Agner, Nathan Chancellor).
- Support security extension for noMMU and other noMMU cleanups (from
Vladimir Murzin).
- Remove unnecessary SMP bringup code (which was incorrectly copy'n'
pasted from the ARM platform implementations) and remove it from the
arch code to discourge further copys of it appearing.
- Add Cortex A9 erratum preventing kexec working on some SoCs.
- AMBA bus identification updates from Mike Leach.
- More use of raw spinlocks to avoid -RT kernel issues (from Yang Shi
and Sebastian Andrzej Siewior).
- MCPM hyp/svc mode mismatch fixes from Marek Szyprowski.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 8849/1: NOMMU: Fix encodings for PMSAv8's PRBAR4/PRLAR4
ARM: 8848/1: virt: Align GIC version check with arm64 counterpart
ARM: 8847/1: pm: fix HYP/SVC mode mismatch when MCPM is used
ARM: 8845/1: use unified assembler in c files
ARM: 8844/1: use unified assembler in assembly files
ARM: 8843/1: use unified assembler in headers
ARM: 8841/1: use unified assembler in macros
ARM: 8840/1: use a raw_spinlock_t in unwind
ARM: 8839/1: kprobe: make patch_lock a raw_spinlock_t
ARM: 8837/1: coresight: etmv4: Update ID register table to add UCI support
ARM: 8836/1: drivers: amba: Update component matching to use the CoreSight UCI values.
ARM: 8838/1: drivers: amba: Updates to component identification for driver matching.
ARM: 8833/1: Ensure that NEON code always compiles with Clang
ARM: avoid Cortex-A9 livelock on tight dmb loops
ARM: smp: remove arch-provided "pen_release"
ARM: actions: remove boot_lock and pen_release
ARM: oxnas: remove CPU hotplug implementation
ARM: qcom: remove unnecessary boot_lock
ARM: 8832/1: NOMMU: Limit visibility for CONFIG_FLASH_{MEM_BASE,SIZE}
ARM: 8831/1: NOMMU: pmsa-v8: remove unneeded semicolon
...
|
|
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"Just a couple of small fixes and cleanups:
- fix memory access if logo is bigger than the screen (Manfred
Schlaegl)
- silence fbcon logo on 'quiet' boots (Prarit Bhargava)
- use kvmalloc() for scrollback buffer in fbcon (Konstantin Khorenko)
- misc fixes (Colin Ian King, YueHaibing, Matteo Croce, Mathieu
Malaterre, Anders Roxell, Arnd Bergmann)
- misc cleanups (Rob Herring, Lubomir Rintel, Greg Kroah-Hartman,
Jani Nikula, Michal Vokáč)"
* tag 'fbdev-v5.1' of git://github.com/bzolnier/linux:
fbdev: mbx: fix a misspelled variable name
fbdev: omap2: fix warnings in dss core
video: fbdev: Fix potential NULL pointer dereference
fbcon: Silence fbcon logo on 'quiet' boots
printk: Export console_printk
ARM: dts: imx28-cfa10036: Fix the reset gpio signal polarity
video: ssd1307fb: Do not hard code active-low reset sequence
dt-bindings: display: ssd1307fb: Remove reset-active-low from examples
fbdev: fbmem: fix memory access if logo is bigger than the screen
video/fbdev: refactor video= cmdline parsing
fbdev: mbx: fix up debugfs file creation
fbdev: omap2: no need to check return value of debugfs_create functions
video: fbdev: geode: remove ifdef OLPC noise
video: offb: annotate implicit fall throughs
omapfb: fix typo
fbdev: Use of_node_name_eq for node name comparisons
fbcon: use kvmalloc() for scrollback buffer
fbdev: chipsfb: remove set but not used variable 'size'
fbdev/via: fix spelling mistake "Expandsion" -> "Expansion"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"We've continued mainly to fix bugs in this round, as f2fs has been
shipped in more devices. Especially, we've focused on stabilizing
checkpoint=disable feature, and provided some interfaces for QA.
Enhancements:
- expose FS_NOCOW_FL for pin_file
- run discard jobs at unmount time with timeout
- tune discarding thread to avoid idling which consumes power
- some checking codes to address vulnerabilities
- give random value to i_generation
- shutdown with more flags for QA
Bug fixes:
- clean up stale objects when mount is failed along with
checkpoint=disable
- fix system being stuck due to wrong count by atomic writes
- handle some corrupted disk cases
- fix a deadlock in f2fs_read_inline_dir
We've also added some minor build error fixes and clean-up patches"
* tag 'f2fs-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (53 commits)
f2fs: set pin_file under CAP_SYS_ADMIN
f2fs: fix to avoid deadlock in f2fs_read_inline_dir()
f2fs: fix to adapt small inline xattr space in __find_inline_xattr()
f2fs: fix to do sanity check with inode.i_inline_xattr_size
f2fs: give some messages for inline_xattr_size
f2fs: don't trigger read IO for beyond EOF page
f2fs: fix to add refcount once page is tagged PG_private
f2fs: remove wrong comment in f2fs_invalidate_page()
f2fs: fix to use kvfree instead of kzfree
f2fs: print more parameters in trace_f2fs_map_blocks
f2fs: trace f2fs_ioc_shutdown
f2fs: fix to avoid deadlock of atomic file operations
f2fs: fix to dirty inode for i_mode recovery
f2fs: give random value to i_generation
f2fs: no need to take page lock in readdir
f2fs: fix to update iostat correctly in IPU path
f2fs: fix encrypted page memory leak
f2fs: make fault injection covering __submit_flush_wait()
f2fs: fix to retry fill_super only if recovery failed
f2fs: silence VM_WARN_ON_ONCE in mempool_alloc
...
|
|
The series to add memcg accounting to KVM allocations[1] states:
There are many KVM kernel memory allocations which are tied to the
life of the VM process and should be charged to the VM process's
cgroup.
While it is correct to account KVM kernel allocations to the cgroup of
the process that created the VM, it's technically incorrect to state
that the KVM kernel memory allocations are tied to the life of the VM
process. This is because the VM itself, i.e. struct kvm, is not tied to
the life of the process which created it, rather it is tied to the life
of its associated file descriptor. In other words, kvm_destroy_vm() is
not invoked until fput() decrements its associated file's refcount to
zero. A simple example is to fork() in Qemu and have the child sleep
indefinitely; kvm_destroy_vm() isn't called until Qemu closes its file
descriptor *and* the rogue child is killed.
The allocations are guaranteed to be *accounted* to the process which
created the VM, but only because KVM's per-{VM,vCPU} ioctls reject the
ioctl() with -EIO if kvm->mm != current->mm. I.e. the child can keep
the VM "alive" but can't do anything useful with its reference.
Note that because 'struct kvm' also holds a reference to the mm_struct
of its owner, the above behavior also applies to userspace allocations.
Given that mucking with a VM's file descriptor can lead to subtle and
undesirable behavior, e.g. memcg charges persisting after a VM is shut
down, explicitly document a VM's lifecycle and its impact on the VM's
resources.
Alternatively, KVM could aggressively free resources when the creating
process exits, e.g. via mmu_notifier->release(). However, mmu_notifier
isn't guaranteed to be available, and freeing resources when the creator
exits is likely to be error prone and fragile as KVM would need to
ensure that it only freed resources that are truly out of reach. In
practice, the existing behavior shouldn't be problematic as a properly
configured system will prevent a child process from being moved out of
the appropriate cgroup hierarchy, i.e. prevent hiding the process from
the OOM killer, and will prevent an unprivileged user from being able to
to hold a reference to struct kvm via another method, e.g. debugfs.
[1]https://patchwork.kernel.org/patch/10806707/
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
