diff options
Diffstat (limited to 'drivers/net/atl1/atl1_hw.c')
| -rw-r--r-- | drivers/net/atl1/atl1_hw.c | 718 |
1 files changed, 718 insertions, 0 deletions
diff --git a/drivers/net/atl1/atl1_hw.c b/drivers/net/atl1/atl1_hw.c new file mode 100644 index 000000000000..08b2d785469d --- /dev/null +++ b/drivers/net/atl1/atl1_hw.c @@ -0,0 +1,718 @@ +/* + * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved. + * Copyright(c) 2006 Chris Snook <csnook@redhat.com> + * Copyright(c) 2006 Jay Cliburn <jcliburn@gmail.com> + * + * Derived from Intel e1000 driver + * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 + * Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#include <linux/types.h> +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/if_vlan.h> +#include <linux/etherdevice.h> +#include <linux/crc32.h> +#include <asm/byteorder.h> + +#include "atl1.h" + +/* + * Reset the transmit and receive units; mask and clear all interrupts. + * hw - Struct containing variables accessed by shared code + * return : ATL1_SUCCESS or idle status (if error) + */ +s32 atl1_reset_hw(struct atl1_hw *hw) +{ + u32 icr; + int i; + + /* + * Clear Interrupt mask to stop board from generating + * interrupts & Clear any pending interrupt events + */ + /* + * iowrite32(0, hw->hw_addr + REG_IMR); + * iowrite32(0xffffffff, hw->hw_addr + REG_ISR); + */ + + /* + * Issue Soft Reset to the MAC. This will reset the chip's + * transmit, receive, DMA. It will not effect + * the current PCI configuration. The global reset bit is self- + * clearing, and should clear within a microsecond. + */ + iowrite32(MASTER_CTRL_SOFT_RST, hw->hw_addr + REG_MASTER_CTRL); + ioread32(hw->hw_addr + REG_MASTER_CTRL); + + iowrite16(1, hw->hw_addr + REG_GPHY_ENABLE); + ioread16(hw->hw_addr + REG_GPHY_ENABLE); + + msleep(1); /* delay about 1ms */ + + /* Wait at least 10ms for All module to be Idle */ + for (i = 0; i < 10; i++) { + icr = ioread32(hw->hw_addr + REG_IDLE_STATUS); + if (!icr) + break; + msleep(1); /* delay 1 ms */ + cpu_relax(); /* FIXME: is this still the right way to do this? */ + } + + if (icr) { + printk (KERN_DEBUG "icr = %x\n", icr); + return icr; + } + + return ATL1_SUCCESS; +} + +/* function about EEPROM + * + * check_eeprom_exist + * return 0 if eeprom exist + */ +static int atl1_check_eeprom_exist(struct atl1_hw *hw) +{ + u32 value; + value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL); + if (value & SPI_FLASH_CTRL_EN_VPD) { + value &= ~SPI_FLASH_CTRL_EN_VPD; + iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL); + } + + value = ioread16(hw->hw_addr + REG_PCIE_CAP_LIST); + return ((value & 0xFF00) == 0x6C00) ? 0 : 1; +} + +static bool atl1_read_eeprom(struct atl1_hw *hw, u32 offset, u32 *p_value) +{ + int i; + u32 control; + + if (offset & 3) + return false; /* address do not align */ + + iowrite32(0, hw->hw_addr + REG_VPD_DATA); + control = (offset & VPD_CAP_VPD_ADDR_MASK) << VPD_CAP_VPD_ADDR_SHIFT; + iowrite32(control, hw->hw_addr + REG_VPD_CAP); + ioread32(hw->hw_addr + REG_VPD_CAP); + + for (i = 0; i < 10; i++) { + msleep(2); + control = ioread32(hw->hw_addr + REG_VPD_CAP); + if (control & VPD_CAP_VPD_FLAG) + break; + } + if (control & VPD_CAP_VPD_FLAG) { + *p_value = ioread32(hw->hw_addr + REG_VPD_DATA); + return true; + } + return false; /* timeout */ +} + +/* + * Reads the value from a PHY register + * hw - Struct containing variables accessed by shared code + * reg_addr - address of the PHY register to read + */ +s32 atl1_read_phy_reg(struct atl1_hw *hw, u16 reg_addr, u16 *phy_data) +{ + u32 val; + int i; + + val = ((u32) (reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT | + MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW | MDIO_CLK_25_4 << + MDIO_CLK_SEL_SHIFT; + iowrite32(val, hw->hw_addr + REG_MDIO_CTRL); + ioread32(hw->hw_addr + REG_MDIO_CTRL); + + for (i = 0; i < MDIO_WAIT_TIMES; i++) { + udelay(2); + val = ioread32(hw->hw_addr + REG_MDIO_CTRL); + if (!(val & (MDIO_START | MDIO_BUSY))) + break; + } + if (!(val & (MDIO_START | MDIO_BUSY))) { + *phy_data = (u16) val; + return ATL1_SUCCESS; + } + return ATL1_ERR_PHY; +} + +#define CUSTOM_SPI_CS_SETUP 2 +#define CUSTOM_SPI_CLK_HI 2 +#define CUSTOM_SPI_CLK_LO 2 +#define CUSTOM_SPI_CS_HOLD 2 +#define CUSTOM_SPI_CS_HI 3 + +static bool atl1_spi_read(struct atl1_hw *hw, u32 addr, u32 *buf) +{ + int i; + u32 value; + + iowrite32(0, hw->hw_addr + REG_SPI_DATA); + iowrite32(addr, hw->hw_addr + REG_SPI_ADDR); + + value = SPI_FLASH_CTRL_WAIT_READY | + (CUSTOM_SPI_CS_SETUP & SPI_FLASH_CTRL_CS_SETUP_MASK) << + SPI_FLASH_CTRL_CS_SETUP_SHIFT | (CUSTOM_SPI_CLK_HI & + SPI_FLASH_CTRL_CLK_HI_MASK) << + SPI_FLASH_CTRL_CLK_HI_SHIFT | (CUSTOM_SPI_CLK_LO & + SPI_FLASH_CTRL_CLK_LO_MASK) << + SPI_FLASH_CTRL_CLK_LO_SHIFT | (CUSTOM_SPI_CS_HOLD & + SPI_FLASH_CTRL_CS_HOLD_MASK) << + SPI_FLASH_CTRL_CS_HOLD_SHIFT | (CUSTOM_SPI_CS_HI & + SPI_FLASH_CTRL_CS_HI_MASK) << + SPI_FLASH_CTRL_CS_HI_SHIFT | (1 & SPI_FLASH_CTRL_INS_MASK) << + SPI_FLASH_CTRL_INS_SHIFT; + + iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL); + + value |= SPI_FLASH_CTRL_START; + iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL); + ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL); + + for (i = 0; i < 10; i++) { + msleep(1); /* 1ms */ + value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL); + if (!(value & SPI_FLASH_CTRL_START)) + break; + } + + if (value & SPI_FLASH_CTRL_START) + return false; + + *buf = ioread32(hw->hw_addr + REG_SPI_DATA); + + return true; +} + +/* + * get_permanent_address + * return 0 if get valid mac address, + */ +static int atl1_get_permanent_address(struct atl1_hw *hw) +{ + u32 addr[2]; + u32 i, control; + u16 reg; + u8 eth_addr[ETH_ALEN]; + bool key_valid; + + if (is_valid_ether_addr(hw->perm_mac_addr)) + return 0; + + /* init */ + addr[0] = addr[1] = 0; + + if (!atl1_check_eeprom_exist(hw)) { /* eeprom exist */ + reg = 0; + key_valid = false; + /* Read out all EEPROM content */ + i = 0; + while (1) { + if (atl1_read_eeprom(hw, i + 0x100, &control)) { + if (key_valid) { + if (reg == REG_MAC_STA_ADDR) + addr[0] = control; + else if (reg == (REG_MAC_STA_ADDR + 4)) + addr[1] = control; + key_valid = false; + } else if ((control & 0xff) == 0x5A) { + key_valid = true; + reg = (u16) (control >> 16); + } else + break; /* assume data end while encount an invalid KEYWORD */ + } else + break; /* read error */ + i += 4; + } + +/* + * The following 2 lines are the Attansic originals. Saving for posterity. + * *(u32 *) & eth_addr[2] = LONGSWAP(addr[0]); + * *(u16 *) & eth_addr[0] = SHORTSWAP(*(u16 *) & addr[1]); + */ + *(u32 *) & eth_addr[2] = swab32(addr[0]); + *(u16 *) & eth_addr[0] = swab16(*(u16 *) & addr[1]); + + if (is_valid_ether_addr(eth_addr)) { + memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN); + return 0; + } + return 1; + } + + /* see if SPI FLAGS exist ? */ + addr[0] = addr[1] = 0; + reg = 0; + key_valid = false; + i = 0; + while (1) { + if (atl1_spi_read(hw, i + 0x1f000, &control)) { + if (key_valid) { + if (reg == REG_MAC_STA_ADDR) + addr[0] = control; + else if (reg == (REG_MAC_STA_ADDR + 4)) + addr[1] = control; + key_valid = false; + } else if ((control & 0xff) == 0x5A) { + key_valid = true; + reg = (u16) (control >> 16); + } else + break; /* data end */ + } else + break; /* read error */ + i += 4; + } + +/* + * The following 2 lines are the Attansic originals. Saving for posterity. + * *(u32 *) & eth_addr[2] = LONGSWAP(addr[0]); + * *(u16 *) & eth_addr[0] = SHORTSWAP(*(u16 *) & addr[1]); + */ + *(u32 *) & eth_addr[2] = swab32(addr[0]); + *(u16 *) & eth_addr[0] = swab16(*(u16 *) & addr[1]); + if (is_valid_ether_addr(eth_addr)) { + memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN); + return 0; + } + return 1; +} + +/* + * Reads the adapter's MAC address from the EEPROM + * hw - Struct containing variables accessed by shared code + */ +s32 atl1_read_mac_addr(struct atl1_hw *hw) +{ + u16 i; + + if (atl1_get_permanent_address(hw)) + random_ether_addr(hw->perm_mac_addr); + + for (i = 0; i < ETH_ALEN; i++) + hw->mac_addr[i] = hw->perm_mac_addr[i]; + return ATL1_SUCCESS; +} + +/* + * Hashes an address to determine its location in the multicast table + * hw - Struct containing variables accessed by shared code + * mc_addr - the multicast address to hash + * + * atl1_hash_mc_addr + * purpose + * set hash value for a multicast address + * hash calcu processing : + * 1. calcu 32bit CRC for multicast address + * 2. reverse crc with MSB to LSB + */ +u32 atl1_hash_mc_addr(struct atl1_hw *hw, u8 *mc_addr) +{ + u32 crc32, value = 0; + int i; + + crc32 = ether_crc_le(6, mc_addr); + crc32 = ~crc32; + for (i = 0; i < 32; i++) + value |= (((crc32 >> i) & 1) << (31 - i)); + + return value; +} + +/* + * Sets the bit in the multicast table corresponding to the hash value. + * hw - Struct containing variables accessed by shared code + * hash_value - Multicast address hash value + */ +void atl1_hash_set(struct atl1_hw *hw, u32 hash_value) +{ + u32 hash_bit, hash_reg; + u32 mta; + + /* + * The HASH Table is a register array of 2 32-bit registers. + * It is treated like an array of 64 bits. We want to set + * bit BitArray[hash_value]. So we figure out what register + * the bit is in, read it, OR in the new bit, then write + * back the new value. The register is determined by the + * upper 7 bits of the hash value and the bit within that + * register are determined by the lower 5 bits of the value. + */ + hash_reg = (hash_value >> 31) & 0x1; + hash_bit = (hash_value >> 26) & 0x1F; + mta = ioread32((hw + REG_RX_HASH_TABLE) + (hash_reg << 2)); + mta |= (1 << hash_bit); + iowrite32(mta, (hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2)); +} + +/* + * Writes a value to a PHY register + * hw - Struct containing variables accessed by shared code + * reg_addr - address of the PHY register to write + * data - data to write to the PHY + */ +s32 atl1_write_phy_reg(struct atl1_hw *hw, u32 reg_addr, u16 phy_data) +{ + int i; + u32 val; + + val = ((u32) (phy_data & MDIO_DATA_MASK)) << MDIO_DATA_SHIFT | + (reg_addr & MDIO_REG_ADDR_MASK) << MDIO_REG_ADDR_SHIFT | + MDIO_SUP_PREAMBLE | + MDIO_START | MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT; + iowrite32(val, hw->hw_addr + REG_MDIO_CTRL); + ioread32(hw->hw_addr + REG_MDIO_CTRL); + + for (i = 0; i < MDIO_WAIT_TIMES; i++) { + udelay(2); + val = ioread32(hw->hw_addr + REG_MDIO_CTRL); + if (!(val & (MDIO_START | MDIO_BUSY))) + break; + } + + if (!(val & (MDIO_START | MDIO_BUSY))) + return ATL1_SUCCESS; + + return ATL1_ERR_PHY; +} + +/* + * Make L001's PHY out of Power Saving State (bug) + * hw - Struct containing variables accessed by shared code + * when power on, L001's PHY always on Power saving State + * (Gigabit Link forbidden) + */ +static s32 atl1_phy_leave_power_saving(struct atl1_hw *hw) +{ + s32 ret; + ret = atl1_write_phy_reg(hw, 29, 0x0029); + if (ret) + return ret; + return atl1_write_phy_reg(hw, 30, 0); +} + +/* + *TODO: do something or get rid of this + */ +s32 atl1_phy_enter_power_saving(struct atl1_hw *hw) +{ +/* s32 ret_val; + * u16 phy_data; + */ + +/* + ret_val = atl1_write_phy_reg(hw, ...); + ret_val = atl1_write_phy_reg(hw, ...); + .... +*/ + return ATL1_SUCCESS; +} + +/* + * Resets the PHY and make all config validate + * hw - Struct containing variables accessed by shared code + * + * Sets bit 15 and 12 of the MII Control regiser (for F001 bug) + */ +static s32 atl1_phy_reset(struct atl1_hw *hw) +{ + s32 ret_val; + u16 phy_data; + + if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR || + hw->media_type == MEDIA_TYPE_1000M_FULL) + phy_data = MII_CR_RESET | MII_CR_AUTO_NEG_EN; + else { + switch (hw->media_type) { + case MEDIA_TYPE_100M_FULL: + phy_data = + MII_CR_FULL_DUPLEX | MII_CR_SPEED_100 | + MII_CR_RESET; + break; + case MEDIA_TYPE_100M_HALF: + phy_data = MII_CR_SPEED_100 | MII_CR_RESET; + break; + case MEDIA_TYPE_10M_FULL: + phy_data = + MII_CR_FULL_DUPLEX | MII_CR_SPEED_10 | MII_CR_RESET; + break; + default: /* MEDIA_TYPE_10M_HALF: */ + phy_data = MII_CR_SPEED_10 | MII_CR_RESET; + break; + } + } + + ret_val = atl1_write_phy_reg(hw, MII_BMCR, phy_data); + if (ret_val) { + u32 val; + int i; + /* pcie serdes link may be down! */ + printk(KERN_DEBUG "%s: autoneg caused pcie phy link down\n", + atl1_driver_name); + + for (i = 0; i < 25; i++) { + msleep(1); + val = ioread32(hw->hw_addr + REG_MDIO_CTRL); + if (!(val & (MDIO_START | MDIO_BUSY))) + break; + } + + if ((val & (MDIO_START | MDIO_BUSY)) != 0) { + printk(KERN_WARNING + "%s: pcie link down at least for 25ms\n", + atl1_driver_name); + return ret_val; + } + } + return ATL1_SUCCESS; +} + +/* + * Configures PHY autoneg and flow control advertisement settings + * hw - Struct containing variables accessed by shared code + */ +s32 atl1_phy_setup_autoneg_adv(struct atl1_hw *hw) +{ + s32 ret_val; + s16 mii_autoneg_adv_reg; + s16 mii_1000t_ctrl_reg; + + /* Read the MII Auto-Neg Advertisement Register (Address 4). */ + mii_autoneg_adv_reg = MII_AR_DEFAULT_CAP_MASK; + + /* Read the MII 1000Base-T Control Register (Address 9). */ + mii_1000t_ctrl_reg = MII_AT001_CR_1000T_DEFAULT_CAP_MASK; + + /* + * First we clear all the 10/100 mb speed bits in the Auto-Neg + * Advertisement Register (Address 4) and the 1000 mb speed bits in + * the 1000Base-T Control Register (Address 9). + */ + mii_autoneg_adv_reg &= ~MII_AR_SPEED_MASK; + mii_1000t_ctrl_reg &= ~MII_AT001_CR_1000T_SPEED_MASK; + + /* + * Need to parse media_type and set up + * the appropriate PHY registers. + */ + switch (hw->media_type) { + case MEDIA_TYPE_AUTO_SENSOR: + mii_autoneg_adv_reg |= (MII_AR_10T_HD_CAPS | + MII_AR_10T_FD_CAPS | + MII_AR_100TX_HD_CAPS | + MII_AR_100TX_FD_CAPS); + mii_1000t_ctrl_reg |= MII_AT001_CR_1000T_FD_CAPS; + break; + + case MEDIA_TYPE_1000M_FULL: + mii_1000t_ctrl_reg |= MII_AT001_CR_1000T_FD_CAPS; + break; + + case MEDIA_TYPE_100M_FULL: + mii_autoneg_adv_reg |= MII_AR_100TX_FD_CAPS; + break; + + case MEDIA_TYPE_100M_HALF: + mii_autoneg_adv_reg |= MII_AR_100TX_HD_CAPS; + break; + + case MEDIA_TYPE_10M_FULL: + mii_autoneg_adv_reg |= MII_AR_10T_FD_CAPS; + break; + + default: + mii_autoneg_adv_reg |= MII_AR_10T_HD_CAPS; + break; + } + + /* flow control fixed to enable all */ + mii_autoneg_adv_reg |= (MII_AR_ASM_DIR | MII_AR_PAUSE); + + hw->mii_autoneg_adv_reg = mii_autoneg_adv_reg; + hw->mii_1000t_ctrl_reg = mii_1000t_ctrl_reg; + + ret_val = atl1_write_phy_reg(hw, MII_ADVERTISE, mii_autoneg_adv_reg); + if (ret_val) + return ret_val; + + ret_val = atl1_write_phy_reg(hw, MII_AT001_CR, mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; + + return ATL1_SUCCESS; +} + +/* + * Configures link settings. + * hw - Struct containing variables accessed by shared code + * Assumes the hardware has previously been reset and the + * transmitter and receiver are not enabled. + */ +static s32 atl1_setup_link(struct atl1_hw *hw) +{ + s32 ret_val; + + /* + * Options: + * PHY will advertise value(s) parsed from + * autoneg_advertised and fc + * no matter what autoneg is , We will not wait link result. + */ + ret_val = atl1_phy_setup_autoneg_adv(hw); + if (ret_val) { + printk(KERN_DEBUG "%s: error setting up autonegotiation\n", + atl1_driver_name); + return ret_val; + } + /* SW.Reset , En-Auto-Neg if needed */ + ret_val = atl1_phy_reset(hw); + if (ret_val) { + printk(KERN_DEBUG "%s: error resetting the phy\n", + atl1_driver_name); + return ret_val; + } + hw->phy_configured = true; + return ret_val; +} + +static struct atl1_spi_flash_dev flash_table[] = { +/* MFR_NAME WRSR READ PRGM WREN WRDI RDSR RDID SECTOR_ERASE CHIP_ERASE */ + {"Atmel", 0x00, 0x03, 0x02, 0x06, 0x04, 0x05, 0x15, 0x52, 0x62}, + {"SST", 0x01, 0x03, 0x02, 0x06, 0x04, 0x05, 0x90, 0x20, 0x60}, + {"ST", 0x01, 0x03, 0x02, 0x06, 0x04, 0x05, 0xAB, 0xD8, 0xC7}, +}; + +static void atl1_init_flash_opcode(struct atl1_hw *hw) +{ + if (hw->flash_vendor >= sizeof(flash_table) / sizeof(flash_table[0])) + hw->flash_vendor = 0; /* ATMEL */ + + /* Init OP table */ + iowrite8(flash_table[hw->flash_vendor].cmd_program, + hw->hw_addr + REG_SPI_FLASH_OP_PROGRAM); + iowrite8(flash_table[hw->flash_vendor].cmd_sector_erase, + hw->hw_addr + REG_SPI_FLASH_OP_SC_ERASE); + iowrite8(flash_table[hw->flash_vendor].cmd_chip_erase, + hw->hw_addr + REG_SPI_FLASH_OP_CHIP_ERASE); + iowrite8(flash_table[hw->flash_vendor].cmd_rdid, + hw->hw_addr + REG_SPI_FLASH_OP_RDID); + iowrite8(flash_table[hw->flash_vendor].cmd_wren, + hw->hw_addr + REG_SPI_FLASH_OP_WREN); + iowrite8(flash_table[hw->flash_vendor].cmd_rdsr, + hw->hw_addr + REG_SPI_FLASH_OP_RDSR); + iowrite8(flash_table[hw->flash_vendor].cmd_wrsr, + hw->hw_addr + REG_SPI_FLASH_OP_WRSR); + iowrite8(flash_table[hw->flash_vendor].cmd_read, + hw->hw_addr + REG_SPI_FLASH_OP_READ); +} + +/* + * Performs basic configuration of the adapter. + * hw - Struct containing variables accessed by shared code + * Assumes that the controller has previously been reset and is in a + * post-reset uninitialized state. Initializes multicast table, + * and Calls routines to setup link + * Leaves the transmit and receive units disabled and uninitialized. + */ +s32 atl1_init_hw(struct atl1_hw *hw) +{ + u32 ret_val = 0; + + /* Zero out the Multicast HASH table */ + iowrite32(0, hw->hw_addr + REG_RX_HASH_TABLE); + /* clear the old settings from the multicast hash table */ + iowrite32(0, (hw->hw_addr + REG_RX_HASH_TABLE) + (1 << 2)); + + atl1_init_flash_opcode(hw); + + if (!hw->phy_configured) { + /* enable GPHY LinkChange Interrrupt */ + ret_val = atl1_write_phy_reg(hw, 18, 0xC00); + if (ret_val) + return ret_val; + /* make PHY out of power-saving state */ + ret_val = atl1_phy_leave_power_saving(hw); + if (ret_val) + return ret_val; + /* Call a subroutine to configure the link */ + ret_val = atl1_setup_link(hw); + } + return ret_val; +} + +/* + * Detects the current speed and duplex settings of the hardware. + * hw - Struct containing variables accessed by shared code + * speed - Speed of the connection + * duplex - Duplex setting of the connection + */ +s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 *speed, u16 *duplex) +{ + s32 ret_val; + u16 phy_data; + + /* ; --- Read PHY Specific Status Register (17) */ + ret_val = atl1_read_phy_reg(hw, MII_AT001_PSSR, &phy_data); + if (ret_val) + return ret_val; + + if (!(phy_data & MII_AT001_PSSR_SPD_DPLX_RESOLVED)) + return ATL1_ERR_PHY_RES; + + switch (phy_data & MII_AT001_PSSR_SPEED) { + case MII_AT001_PSSR_1000MBS: + *speed = SPEED_1000; + break; + case MII_AT001_PSSR_100MBS: + *speed = SPEED_100; + break; + case MII_AT001_PSSR_10MBS: + *speed = SPEED_10; + break; + default: + printk(KERN_DEBUG "%s: error getting speed\n", + atl1_driver_name); + return ATL1_ERR_PHY_SPEED; + break; + } + if (phy_data & MII_AT001_PSSR_DPLX) + *duplex = FULL_DUPLEX; + else + *duplex = HALF_DUPLEX; + + return ATL1_SUCCESS; +} + +void atl1_set_mac_addr(struct atl1_hw *hw) +{ + u32 value; + /* + * 00-0B-6A-F6-00-DC + * 0: 6AF600DC 1: 000B + * low dword + */ + value = (((u32) hw->mac_addr[2]) << 24) | + (((u32) hw->mac_addr[3]) << 16) | + (((u32) hw->mac_addr[4]) << 8) | (((u32) hw->mac_addr[5])); + iowrite32(value, hw->hw_addr + REG_MAC_STA_ADDR); + /* high dword */ + value = (((u32) hw->mac_addr[0]) << 8) | (((u32) hw->mac_addr[1])); + iowrite32(value, (hw->hw_addr + REG_MAC_STA_ADDR) + (1 << 2)); +} |