diff options
Diffstat (limited to 'arch/arm/boot/dts/imx51-zii-rdu1.dts')
| -rw-r--r-- | arch/arm/boot/dts/imx51-zii-rdu1.dts | 103 |
1 files changed, 96 insertions, 7 deletions
diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/imx51-zii-rdu1.dts index 5306b78de0ca..e45a15ceb94b 100644 --- a/arch/arm/boot/dts/imx51-zii-rdu1.dts +++ b/arch/arm/boot/dts/imx51-zii-rdu1.dts @@ -51,6 +51,11 @@ stdout-path = &uart1; }; + /* Will be filled by the bootloader */ + memory@90000000 { + reg = <0x90000000 0>; + }; + aliases { mdio-gpio0 = &mdio_gpio; rtc0 = &ds1341; @@ -202,8 +207,6 @@ switch@0 { compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 0>; @@ -457,7 +460,10 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_esdhc1>; bus-width = <4>; + no-1-8-v; non-removable; + no-sdio; + no-sd; status = "okay"; }; @@ -470,6 +476,17 @@ status = "okay"; }; +&gpio1 { + unused-sd3-wp-gpio { + /* + * See pinctrl_esdhc1 below for more details on this + */ + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + }; +}; + &i2c2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c2>; @@ -491,7 +508,7 @@ }; ds1341: rtc@68 { - compatible = "maxim,ds1341"; + compatible = "dallas,ds1341"; reg = <0x68>; }; @@ -518,7 +535,7 @@ }; touchscreen@20 { - compatible = "syna,rmi4_i2c"; + compatible = "syna,rmi4-i2c"; reg = <0x20>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ts>; @@ -536,8 +553,8 @@ rmi4-f11@11 { reg = <0x11>; - touch-inverted-y; - touch-swapped-x-y; + touchscreen-inverted-x; + touchscreen-swapped-x-y; syna,sensor-type = <1>; }; }; @@ -548,6 +565,10 @@ remote-endpoint = <&display_in>; }; +&pmu { + secure-reg-access; +}; + &ssi2 { status = "okay"; }; @@ -568,6 +589,52 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart3>; status = "okay"; + + rave-sp { + compatible = "zii,rave-sp-rdu1"; + current-speed = <38400>; + #address-cells = <1>; + #size-cells = <1>; + + watchdog { + compatible = "zii,rave-sp-watchdog"; + }; + + backlight { + compatible = "zii,rave-sp-backlight"; + }; + + pwrbutton { + compatible = "zii,rave-sp-pwrbutton"; + }; + + eeprom@a3 { + compatible = "zii,rave-sp-eeprom"; + reg = <0xa3 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + zii,eeprom-name = "dds-eeprom"; + }; + + eeprom@a4 { + compatible = "zii,rave-sp-eeprom"; + reg = <0xa4 0x4000>; + #address-cells = <1>; + #size-cells = <1>; + zii,eeprom-name = "main-eeprom"; + }; + + eeprom@ae { + compatible = "zii,rave-sp-eeprom"; + reg = <0xae 0x200>; + zii,eeprom-name = "switch-eeprom"; + /* + * Not all RDU1s have this functionality, so we + * rely on the bootloader to enable this + */ + status = "disabled"; + }; + }; }; &usbh1 { @@ -577,6 +644,7 @@ phy_type = "ulpi"; fsl,usbphy = <&usbh1phy>; disable-over-current; + maximum-speed = "full-speed"; vbus-supply = <®_5p0v_main>; status = "okay"; }; @@ -604,6 +672,10 @@ status = "okay"; }; +&wdog1 { + status = "disabled"; +}; + &iomuxc { pinctrl_ampgpio: ampgpiogrp { fsl,pins = < @@ -644,6 +716,23 @@ MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5 MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5 MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5 + /* + * GPIO1_1 is not directly used by eSDHC1 in + * any capacity, but earlier versions of RDU1 + * used that pin as WP GPIO for eSDHC3 and + * because of that that pad has an external + * pull-up resistor. This is problematic + * because out of reset the pad is configured + * as ALT0 which serves as SD1_WP, which, when + * pulled high by and external pull-up, will + * inhibit execution of any write request to + * attached eMMC device. + * + * To avoid this problem we configure the pad + * to ALT1/GPIO and avoid driving SD1_WP + * signal high. + */ + MX51_PAD_GPIO1_1__GPIO1_1 0x0000 >; }; @@ -754,7 +843,7 @@ pinctrl_ts: tsgrp { fsl,pins = < - MX51_PAD_CSI1_D8__GPIO3_12 0x85 + MX51_PAD_CSI1_D8__GPIO3_12 0x04 MX51_PAD_CSI1_D9__GPIO3_13 0x85 >; }; |