diff options
Diffstat (limited to 'Documentation/devicetree')
280 files changed, 5094 insertions, 1032 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index f747f47922c5..69880560c0f0 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -25,6 +25,10 @@ Boards with the Amlogic Meson8b SoC shall have the following properties: Required root node property: compatible: "amlogic,meson8b"; +Boards with the Amlogic Meson8m2 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson8m2"; + Boards with the Amlogic Meson GXBaby SoC shall have the following properties: Required root node property: compatible: "amlogic,meson-gxbb"; @@ -54,6 +58,8 @@ Board compatible values (alphabetically, grouped by SoC): - "hardkernel,odroid-c1" (Meson8b) - "tronfy,mxq" (Meson8b) + - "tronsmart,mxiii-plus" (Meson8m2) + - "amlogic,p200" (Meson gxbb) - "amlogic,p201" (Meson gxbb) - "friendlyarm,nanopi-k2" (Meson gxbb) diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index 3e3efa046ac5..1e3e29a545e2 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -34,6 +34,10 @@ Raspberry Pi 3 Model B Required root node properties: compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; +Raspberry Pi 3 Model B+ +Required root node properties: +compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; + Raspberry Pi Compute Module Required root node properties: compatible = "raspberrypi,compute-module", "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,g3dsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,g3dsys.txt new file mode 100644 index 000000000000..7de43bf41fdc --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,g3dsys.txt @@ -0,0 +1,30 @@ +MediaTek g3dsys controller +============================ + +The MediaTek g3dsys controller provides various clocks and reset controller to +the GPU. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt2701-g3dsys", "syscon": + for MT2701 SoC + - "mediatek,mt7623-g3dsys", "mediatek,mt2701-g3dsys", "syscon": + for MT7623 SoC +- #clock-cells: Must be 1 +- #reset-cells: Must be 1 + +The g3dsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +g3dsys: clock-controller@13000000 { + compatible = "mediatek,mt7623-g3dsys", + "mediatek,mt2701-g3dsys", + "syscon"; + reg = <0 0x13000000 0 0x200>; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 14510b215480..bdadc3da9556 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -21,8 +21,6 @@ Required root node properties: - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. - "samsung,tm2" - for Exynos5433-based Samsung TM2 board. - "samsung,tm2e" - for Exynos5433-based Samsung TM2E board. - - "samsung,sd5v1" - for Exynos5440-based Samsung board. - - "samsung,ssdk5440" - for Exynos5440-based Samsung board. * Other companies Exynos SoC based * FriendlyARM diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index d3d1df97834f..d8cf740132c6 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -21,6 +21,8 @@ SoCs: compatible = "renesas,r8a7744" - RZ/G1E (R8A77450) compatible = "renesas,r8a7745" + - RZ/G1C (R8A77470) + compatible = "renesas,r8a77470" - R-Car M1A (R8A77781) compatible = "renesas,r8a7778" - R-Car H1 (R8A77790) @@ -45,6 +47,8 @@ SoCs: compatible = "renesas,r8a77970" - R-Car V3H (R8A77980) compatible = "renesas,r8a77980" + - R-Car E3 (R8A77990) + compatible = "renesas,r8a77990" - R-Car D3 (R8A77995) compatible = "renesas,r8a77995" @@ -67,6 +71,8 @@ Boards: compatible = "renesas,draak", "renesas,r8a77995" - Eagle (RTP0RC77970SEB0010S) compatible = "renesas,eagle", "renesas,r8a77970" + - Ebisu (RTP0RC77990SEB0010S) + compatible = "renesas,ebisu", "renesas,r8a77990" - Genmai (RTK772100BC00000BR) compatible = "renesas,genmai", "renesas,r7s72100" - GR-Peach (X28A-M01-E/F) @@ -78,6 +84,8 @@ Boards: compatible = "renesas,h3ulcb", "renesas,r8a7795" - Henninger compatible = "renesas,henninger", "renesas,r8a7791" + - iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S) + compatible = "iwave,g23s", "renesas,r8a77470" - iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D) compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745" - iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) @@ -108,7 +116,7 @@ Boards: compatible = "renesas,salvator-x", "renesas,r8a7795" - Salvator-X (RTP0RC7796SIPB0011S) compatible = "renesas,salvator-x", "renesas,r8a7796" - - Salvator-X (RTP0RC7796SIPB0011S (M3N)) + - Salvator-X (RTP0RC7796SIPB0011S (M3-N)) compatible = "renesas,salvator-x", "renesas,r8a77965" - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S) compatible = "renesas,salvator-xs", "renesas,r8a7795" @@ -124,6 +132,8 @@ Boards: compatible = "renesas,sk-rzg1m", "renesas,r8a7743" - Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD) compatible = "renesas,stout", "renesas,r8a7790" + - V3HSK (Y-ASK-RCAR-V3H-WS10) + compatible = "renesas,v3hsk", "renesas,r8a77980" - V3MSK (Y-ASK-RCAR-V3M-WS10) compatible = "renesas,v3msk", "renesas,r8a77970" - Wheat (RTP0RC7792ASKB0000JE) diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32-syscon.txt b/Documentation/devicetree/bindings/arm/stm32/stm32-syscon.txt new file mode 100644 index 000000000000..99980aee26e5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/stm32/stm32-syscon.txt @@ -0,0 +1,14 @@ +STMicroelectronics STM32 Platforms System Controller + +Properties: + - compatible : should contain two values. First value must be : + - " st,stm32mp157-syscfg " - for stm32mp157 based SoCs, + second value must be always "syscon". + - reg : offset and length of the register set. + + Example: + syscfg: syscon@50020000 { + compatible = "st,stm32mp157-syscfg", "syscon"; + reg = <0x50020000 0x400>; + }; + diff --git a/Documentation/devicetree/bindings/arm/stm32.txt b/Documentation/devicetree/bindings/arm/stm32/stm32.txt index 6808ed9ddfd5..6808ed9ddfd5 100644 --- a/Documentation/devicetree/bindings/arm/stm32.txt +++ b/Documentation/devicetree/bindings/arm/stm32/stm32.txt diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt deleted file mode 100644 index bdf1a612422b..000000000000 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt +++ /dev/null @@ -1,18 +0,0 @@ -NVIDIA Tegra30 MC(Memory Controller) - -Required properties: -- compatible : "nvidia,tegra30-mc" -- reg : Should contain 4 register ranges(address and length); see the - example below. Note that the MC registers are interleaved with the - SMMU registers, and hence must be represented as multiple ranges. -- interrupts : Should contain MC General interrupt. - -Example: - memory-controller { - compatible = "nvidia,tegra30-mc"; - reg = <0x7000f000 0x010 - 0x7000f03c 0x1b4 - 0x7000f200 0x028 - 0x7000f284 0x17c>; - interrupts = <0 77 0x04>; - }; diff --git a/Documentation/devicetree/bindings/arm/ux500/boards.txt b/Documentation/devicetree/bindings/arm/ux500/boards.txt index 7334c24625fc..0fa429534f49 100644 --- a/Documentation/devicetree/bindings/arm/ux500/boards.txt +++ b/Documentation/devicetree/bindings/arm/ux500/boards.txt @@ -26,7 +26,7 @@ interrupt-controller: see binding for interrupt-controller/arm,gic.txt timer: - see binding for arm/twd.txt + see binding for timer/arm,twd.txt clocks: see binding for clocks/ux500.txt diff --git a/Documentation/devicetree/bindings/bus/ti-sysc.txt b/Documentation/devicetree/bindings/bus/ti-sysc.txt index 2957a9ae291f..d8ed5b780ed9 100644 --- a/Documentation/devicetree/bindings/bus/ti-sysc.txt +++ b/Documentation/devicetree/bindings/bus/ti-sysc.txt @@ -79,7 +79,11 @@ Optional properties: mode as for example omap4 L4_CFG_CLKCTRL - clock-names should contain at least "fck", and optionally also "ick" - depending on the SoC and the interconnect target module + depending on the SoC and the interconnect target module, + some interconnect target modules also need additional + optional clocks that can be specified as listed in TRM + for the related CLKCTRL register bits 8 to 15 such as + "dbclk" or "clk32k" depending on their role - ti,hwmods optional TI interconnect module name to use legacy hwmod platform data diff --git a/Documentation/devicetree/bindings/clock/actions,s900-cmu.txt b/Documentation/devicetree/bindings/clock/actions,s900-cmu.txt new file mode 100644 index 000000000000..93e4fb827cd6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/actions,s900-cmu.txt @@ -0,0 +1,47 @@ +* Actions S900 Clock Management Unit (CMU) + +The Actions S900 clock management unit generates and supplies clock to various +controllers within the SoC. The clock binding described here is applicable to +S900 SoC. + +Required Properties: + +- compatible: should be "actions,s900-cmu" +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: Reference to the parent clocks ("hosc", "losc") +- #clock-cells: should be 1. + +Each clock is assigned an identifier, and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/actions,s900-cmu.h header and can be used in device +tree sources. + +External clocks: + +The hosc clock used as input for the plls is generated outside the SoC. It is +expected that it is defined using standard clock bindings as "hosc". + +Actions S900 CMU also requires one more clock: + - "losc" - internal low frequency oscillator + +Example: Clock Management Unit node: + + cmu: clock-controller@e0160000 { + compatible = "actions,s900-cmu"; + reg = <0x0 0xe0160000 0x0 0x1000>; + clocks = <&hosc>, <&losc>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes clock generated by the clock +management unit: + + uart: serial@e012a000 { + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe012a000 0x0 0x2000>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART5>; + }; diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt index 786dc39ca904..3a880528030e 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -9,6 +9,7 @@ Required Properties: - GXBB (S905) : "amlogic,meson-gxbb-aoclkc" - GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc" - GXM (S912) : "amlogic,meson-gxm-aoclkc" + - AXG (A113D, A113X) : "amlogic,meson-axg-aoclkc" followed by the common "amlogic,meson-gx-aoclkc" - #clock-cells: should be 1. diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt index e2b377ed6f91..e950599566a9 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -10,9 +10,6 @@ Required Properties: "amlogic,gxl-clkc" for GXL and GXM SoC, "amlogic,axg-clkc" for AXG SoC. -- reg: physical base address of the clock controller and length of memory - mapped region. - - #clock-cells: should be 1. Each clock is assigned an identifier and client nodes can use this identifier @@ -20,13 +17,22 @@ to specify the clock which they consume. All available clocks are defined as preprocessor macros in the dt-bindings/clock/gxbb-clkc.h header and can be used in device tree sources. +Parent node should have the following properties : +- compatible: "syscon", "simple-mfd, and "amlogic,meson-gx-hhi-sysctrl" or + "amlogic,meson-axg-hhi-sysctrl" +- reg: base address and size of the HHI system control register space. + Example: Clock controller node: - clkc: clock-controller@c883c000 { +sysctrl: system-controller@0 { + compatible = "amlogic,meson-gx-hhi-sysctrl", "syscon", "simple-mfd"; + reg = <0 0 0 0x400>; + + clkc: clock-controller { #clock-cells = <1>; compatible = "amlogic,gxbb-clkc"; - reg = <0x0 0xc883c000 0x0 0x3db>; }; +}; Example: UART controller node that consumes the clock generated by the clock controller: diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt index f8e4a93466cb..ab730ea0a560 100644 --- a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt +++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt @@ -276,36 +276,38 @@ These clock IDs are defined in: clk_ts_500_ref genpll2 2 BCM_SR_GENPLL2_TS_500_REF_CLK clk_125_nitro genpll2 3 BCM_SR_GENPLL2_125_NITRO_CLK clk_chimp genpll2 4 BCM_SR_GENPLL2_CHIMP_CLK - clk_nic_flash genpll2 5 BCM_SR_GENPLL2_NIC_FLASH + clk_nic_flash genpll2 5 BCM_SR_GENPLL2_NIC_FLASH_CLK + clk_fs genpll2 6 BCM_SR_GENPLL2_FS_CLK genpll3 crystal 0 BCM_SR_GENPLL3 clk_hsls genpll3 1 BCM_SR_GENPLL3_HSLS_CLK clk_sdio genpll3 2 BCM_SR_GENPLL3_SDIO_CLK genpll4 crystal 0 BCM_SR_GENPLL4 - ccn genpll4 1 BCM_SR_GENPLL4_CCN_CLK + clk_ccn genpll4 1 BCM_SR_GENPLL4_CCN_CLK clk_tpiu_pll genpll4 2 BCM_SR_GENPLL4_TPIU_PLL_CLK - noc_clk genpll4 3 BCM_SR_GENPLL4_NOC_CLK + clk_noc genpll4 3 BCM_SR_GENPLL4_NOC_CLK clk_chclk_fs4 genpll4 4 BCM_SR_GENPLL4_CHCLK_FS4_CLK clk_bridge_fscpu genpll4 5 BCM_SR_GENPLL4_BRIDGE_FSCPU_CLK - genpll5 crystal 0 BCM_SR_GENPLL5 - fs4_hf_clk genpll5 1 BCM_SR_GENPLL5_FS4_HF_CLK - crypto_ae_clk genpll5 2 BCM_SR_GENPLL5_CRYPTO_AE_CLK - raid_ae_clk genpll5 3 BCM_SR_GENPLL5_RAID_AE_CLK + clk_fs4_hf genpll5 1 BCM_SR_GENPLL5_FS4_HF_CLK + clk_crypto_ae genpll5 2 BCM_SR_GENPLL5_CRYPTO_AE_CLK + clk_raid_ae genpll5 3 BCM_SR_GENPLL5_RAID_AE_CLK genpll6 crystal 0 BCM_SR_GENPLL6 - 48_usb genpll6 1 BCM_SR_GENPLL6_48_USB_CLK + clk_48_usb genpll6 1 BCM_SR_GENPLL6_48_USB_CLK lcpll0 crystal 0 BCM_SR_LCPLL0 clk_sata_refp lcpll0 1 BCM_SR_LCPLL0_SATA_REFP_CLK clk_sata_refn lcpll0 2 BCM_SR_LCPLL0_SATA_REFN_CLK - clk_usb_ref lcpll0 3 BCM_SR_LCPLL0_USB_REF_CLK - sata_refpn lcpll0 3 BCM_SR_LCPLL0_SATA_REFPN_CLK + clk_sata_350 lcpll0 3 BCM_SR_LCPLL0_SATA_350_CLK + clk_sata_500 lcpll0 4 BCM_SR_LCPLL0_SATA_500_CLK lcpll1 crystal 0 BCM_SR_LCPLL1 - wan lcpll1 1 BCM_SR_LCPLL0_WAN_CLK + clk_wan lcpll1 1 BCM_SR_LCPLL1_WAN_CLK + clk_usb_ref lcpll1 2 BCM_SR_LCPLL1_USB_REF_CLK + clk_crmu_ts lcpll1 3 BCM_SR_LCPLL1_CRMU_TS_CLK lcpll_pcie crystal 0 BCM_SR_LCPLL_PCIE - pcie_phy_ref lcpll1 1 BCM_SR_LCPLL_PCIE_PHY_REF_CLK + clk_pcie_phy_ref lcpll1 1 BCM_SR_LCPLL_PCIE_PHY_REF_CLK diff --git a/Documentation/devicetree/bindings/clock/nuvoton,npcm750-clk.txt b/Documentation/devicetree/bindings/clock/nuvoton,npcm750-clk.txt new file mode 100644 index 000000000000..f82064546d11 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nuvoton,npcm750-clk.txt @@ -0,0 +1,100 @@ +* Nuvoton NPCM7XX Clock Controller + +Nuvoton Poleg BMC NPCM7XX contains an integrated clock controller, which +generates and supplies clocks to all modules within the BMC. + +External clocks: + +There are six fixed clocks that are generated outside the BMC. All clocks are of +a known fixed value that cannot be changed. clk_refclk, clk_mcbypck and +clk_sysbypck are inputs to the clock controller. +clk_rg1refck, clk_rg2refck and clk_xin are external clocks suppling the +network. They are set on the device tree, but not used by the clock module. The +network devices use them directly. +Example can be found below. + +All available clocks are defined as preprocessor macros in: +dt-bindings/clock/nuvoton,npcm7xx-clock.h +and can be reused as DT sources. + +Required Properties of clock controller: + + - compatible: "nuvoton,npcm750-clk" : for clock controller of Nuvoton + Poleg BMC NPCM750 + + - reg: physical base address of the clock controller and length of + memory mapped region. + + - #clock-cells: should be 1. + +Example: Clock controller node: + + clk: clock-controller@f0801000 { + compatible = "nuvoton,npcm750-clk"; + #clock-cells = <1>; + reg = <0xf0801000 0x1000>; + clock-names = "refclk", "sysbypck", "mcbypck"; + clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>; + }; + +Example: Required external clocks for network: + + /* external reference clock */ + clk_refclk: clk-refclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "refclk"; + }; + + /* external reference clock for cpu. float in normal operation */ + clk_sysbypck: clk-sysbypck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <800000000>; + clock-output-names = "sysbypck"; + }; + + /* external reference clock for MC. float in normal operation */ + clk_mcbypck: clk-mcbypck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <800000000>; + clock-output-names = "mcbypck"; + }; + + /* external clock signal rg1refck, supplied by the phy */ + clk_rg1refck: clk-rg1refck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + clock-output-names = "clk_rg1refck"; + }; + + /* external clock signal rg2refck, supplied by the phy */ + clk_rg2refck: clk-rg2refck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + clock-output-names = "clk_rg2refck"; + }; + + clk_xin: clk-xin { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + clock-output-names = "clk_xin"; + }; + + +Example: GMAC controller node that consumes two clocks: a generated clk by the +clock controller and a fixed clock from DT (clk_rg1refck). + + ethernet0: ethernet@f0802000 { + compatible = "snps,dwmac"; + reg = <0xf0802000 0x2000>; + interrupts = <0 14 4>; + interrupt-names = "macirq"; + clocks = <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>; + clock-names = "stmmaceth", "clk_gmac"; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 551d03be9665..664ea1fd6c76 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -17,7 +17,9 @@ Required properties : "qcom,gcc-msm8974pro-ac" "qcom,gcc-msm8994" "qcom,gcc-msm8996" + "qcom,gcc-msm8998" "qcom,gcc-mdm9615" + "qcom,gcc-sdm845" - reg : shall contain base register location and length - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt b/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt new file mode 100644 index 000000000000..3c007653da31 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt @@ -0,0 +1,22 @@ +Qualcomm Technologies, Inc. RPMh Clocks +------------------------------------------------------- + +Resource Power Manager Hardened (RPMh) manages shared resources on +some Qualcomm Technologies Inc. SoCs. It accepts clock requests from +other hardware subsystems via RSC to control clocks. + +Required properties : +- compatible : shall contain "qcom,sdm845-rpmh-clk" + +- #clock-cells : must contain 1 + +Example : + +#include <dt-bindings/clock/qcom,rpmh.h> + + &apps_rsc { + rpmhcc: clock-controller { + compatible = "qcom,sdm845-rpmh-clk"; + #clock-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,videocc.txt b/Documentation/devicetree/bindings/clock/qcom,videocc.txt new file mode 100644 index 000000000000..e7c035afa778 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,videocc.txt @@ -0,0 +1,19 @@ +Qualcomm Video Clock & Reset Controller Binding +----------------------------------------------- + +Required properties : +- compatible : shall contain "qcom,sdm845-videocc" +- reg : shall contain base register location and length +- #clock-cells : from common clock binding, shall contain 1. +- #power-domain-cells : from generic power domain binding, shall contain 1. + +Optional properties : +- #reset-cells : from common reset binding, shall contain 1. + +Example: + videocc: clock-controller@ab00000 { + compatible = "qcom,sdm845-videocc"; + reg = <0xab00000 0x10000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index 773a5226342f..db542abadb75 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -15,6 +15,7 @@ Required Properties: - compatible: Must be one of: - "renesas,r8a7743-cpg-mssr" for the r8a7743 SoC (RZ/G1M) - "renesas,r8a7745-cpg-mssr" for the r8a7745 SoC (RZ/G1E) + - "renesas,r8a77470-cpg-mssr" for the r8a77470 SoC (RZ/G1C) - "renesas,r8a7790-cpg-mssr" for the r8a7790 SoC (R-Car H2) - "renesas,r8a7791-cpg-mssr" for the r8a7791 SoC (R-Car M2-W) - "renesas,r8a7792-cpg-mssr" for the r8a7792 SoC (R-Car V2H) @@ -25,6 +26,7 @@ Required Properties: - "renesas,r8a77965-cpg-mssr" for the r8a77965 SoC (R-Car M3-N) - "renesas,r8a77970-cpg-mssr" for the r8a77970 SoC (R-Car V3M) - "renesas,r8a77980-cpg-mssr" for the r8a77980 SoC (R-Car V3H) + - "renesas,r8a77990-cpg-mssr" for the r8a77990 SoC (R-Car E3) - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3) - reg: Base address and length of the memory resource used by the CPG/MSSR @@ -33,10 +35,12 @@ Required Properties: - clocks: References to external parent clocks, one entry for each entry in clock-names - clock-names: List of external parent clock names. Valid names are: - - "extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794, - r8a7795, r8a7796, r8a77965, r8a77970, r8a77980, r8a77995) + - "extal" (r8a7743, r8a7745, r8a77470, r8a7790, r8a7791, r8a7792, + r8a7793, r8a7794, r8a7795, r8a7796, r8a77965, r8a77970, + r8a77980, r8a77990, r8a77995) - "extalr" (r8a7795, r8a7796, r8a77965, r8a77970, r8a77980) - - "usb_extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7793, r8a7794) + - "usb_extal" (r8a7743, r8a7745, r8a77470, r8a7790, r8a7791, r8a7793, + r8a7794) - #clock-cells: Must be 2 - For CPG core clocks, the two clock specifier cells must be "CPG_CORE" diff --git a/Documentation/devicetree/bindings/clock/rockchip.txt b/Documentation/devicetree/bindings/clock/rockchip.txt deleted file mode 100644 index 22f6769e5d4a..000000000000 --- a/Documentation/devicetree/bindings/clock/rockchip.txt +++ /dev/null @@ -1,77 +0,0 @@ -Device Tree Clock bindings for arch-rockchip - -This binding uses the common clock binding[1]. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt - -== Gate clocks == - -These bindings are deprecated! -Please use the soc specific CRU bindings instead. - -The gate registers form a continuos block which makes the dt node -structure a matter of taste, as either all gates can be put into -one gate clock spanning all registers or they can be divided into -the 10 individual gates containing 16 clocks each. -The code supports both approaches. - -Required properties: -- compatible : "rockchip,rk2928-gate-clk" -- reg : shall be the control register address(es) for the clock. -- #clock-cells : from common clock binding; shall be set to 1 -- clock-output-names : the corresponding gate names that the clock controls -- clocks : should contain the parent clock for each individual gate, - therefore the number of clocks elements should match the number of - clock-output-names - -Example using multiple gate clocks: - - clk_gates0: gate-clk@200000d0 { - compatible = "rockchip,rk2928-gate-clk"; - reg = <0x200000d0 0x4>; - clocks = <&dummy>, <&dummy>, - <&dummy>, <&dummy>, - <&dummy>, <&dummy>, - <&dummy>, <&dummy>, - <&dummy>, <&dummy>, - <&dummy>, <&dummy>, - <&dummy>, <&dummy>, - <&dummy>, <&dummy>; - - clock-output-names = - "gate_core_periph", "gate_cpu_gpll", - "gate_ddrphy", "gate_aclk_cpu", - "gate_hclk_cpu", "gate_pclk_cpu", - "gate_atclk_cpu", "gate_i2s0", - "gate_i2s0_frac", "gate_i2s1", - "gate_i2s1_frac", "gate_i2s2", - "gate_i2s2_frac", "gate_spdif", - "gate_spdif_frac", "gate_testclk"; - - #clock-cells = <1>; - }; - - clk_gates1: gate-clk@200000d4 { - compatible = "rockchip,rk2928-gate-clk"; - reg = <0x200000d4 0x4>; - clocks = <&xin24m>, <&xin24m>, - <&xin24m>, <&dummy>, - <&dummy>, <&xin24m>, - <&xin24m>, <&dummy>, - <&xin24m>, <&dummy>, - <&xin24m>, <&dummy>, - <&xin24m>, <&dummy>, - <&xin24m>, <&dummy>; - - clock-output-names = - "gate_timer0", "gate_timer1", - "gate_timer2", "gate_jtag", - "gate_aclk_lcdc1_src", "gate_otgphy0", - "gate_otgphy1", "gate_ddr_gpll", - "gate_uart0", "gate_frac_uart0", - "gate_uart1", "gate_frac_uart1", - "gate_uart2", "gate_frac_uart2", - "gate_uart3", "gate_frac_uart3"; - - #clock-cells = <1>; - }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt index 7364953d0d0b..45ac19bfa0a9 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -31,10 +31,10 @@ This binding uses the common clock binding[1]. Each subnode should use the binding described in [2]..[7] [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[3] Documentation/devicetree/bindings/clock/st,clkgen-mux.txt -[4] Documentation/devicetree/bindings/clock/st,clkgen-pll.txt -[7] Documentation/devicetree/bindings/clock/st,quadfs.txt -[8] Documentation/devicetree/bindings/clock/st,flexgen.txt +[3] Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt +[4] Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +[7] Documentation/devicetree/bindings/clock/st/st,quadfs.txt +[8] Documentation/devicetree/bindings/clock/st/st,flexgen.txt Required properties: diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index 460ef27b1008..47d2e902ced4 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -21,6 +21,7 @@ Required properties : - "allwinner,sun50i-a64-r-ccu" - "allwinner,sun50i-h5-ccu" - "allwinner,sun50i-h6-ccu" + - "allwinner,sun50i-h6-r-ccu" - "nextthing,gr8-ccu" - reg: Must contain the registers base address and length @@ -35,7 +36,7 @@ Required properties : For the main CCU on H6, one more clock is needed: - "iosc": the SoC's internal frequency oscillator -For the PRCM CCUs on A83T/H3/A64, two more clocks are needed: +For the PRCM CCUs on A83T/H3/A64/H6, two more clocks are needed: - "pll-periph": the SoC's peripheral PLL from the main CCU - "iosc": the SoC's internal frequency oscillator diff --git a/Documentation/devicetree/bindings/clock/ti/gate.txt b/Documentation/devicetree/bindings/clock/ti/gate.txt index 03f8fdee62a7..56d603c1f716 100644 --- a/Documentation/devicetree/bindings/clock/ti/gate.txt +++ b/Documentation/devicetree/bindings/clock/ti/gate.txt @@ -10,7 +10,7 @@ will be controlled instead and the corresponding hw-ops for that is used. [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/gate-clock.txt +[2] Documentation/devicetree/bindings/clock/gpio-gate-clock.txt [3] Documentation/devicetree/bindings/clock/ti/clockdomain.txt Required properties: diff --git a/Documentation/devicetree/bindings/clock/ti/interface.txt b/Documentation/devicetree/bindings/clock/ti/interface.txt index 3111a409fea6..3f4704040140 100644 --- a/Documentation/devicetree/bindings/clock/ti/interface.txt +++ b/Documentation/devicetree/bindings/clock/ti/interface.txt @@ -9,7 +9,7 @@ companion clock finding (match corresponding functional gate clock) and hardware autoidle enable / disable. [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/gate-clock.txt +[2] Documentation/devicetree/bindings/clock/gpio-gate-clock.txt Required properties: - compatible : shall be one of: diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-mediatek.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-mediatek.txt index d36f07e0a2bb..0551c78619de 100644 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-mediatek.txt +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-mediatek.txt @@ -8,7 +8,7 @@ Required properties: "intermediate" - A parent of "cpu" clock which is used as "intermediate" clock source (usually MAINPLL) when the original CPU PLL is under transition and not stable yet. - Please refer to Documentation/devicetree/bindings/clk/clock-bindings.txt for + Please refer to Documentation/devicetree/bindings/clock/clock-bindings.txt for generic clock consumer properties. - operating-points-v2: Please refer to Documentation/devicetree/bindings/opp/opp.txt for detail. diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt index d6d2833482c9..fc2bcbe26b1e 100644 --- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt @@ -12,7 +12,7 @@ Required properties: - clocks: Phandles for clock specified in "clock-names" property - clock-names : The name of clock used by the DFI, must be "pclk_ddr_mon"; -- operating-points-v2: Refer to Documentation/devicetree/bindings/power/opp.txt +- operating-points-v2: Refer to Documentation/devicetree/bindings/opp/opp.txt for details. - center-supply: DMC supply node. - status: Marks the node enabled/disabled. diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 0047b1394c70..2c887536258c 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -14,7 +14,13 @@ Required properties: "adi,adv7513" "adi,adv7533" -- reg: I2C slave address +- reg: I2C slave addresses + The ADV7511 internal registers are split into four pages exposed through + different I2C addresses, creating four register maps. Each map has it own + I2C address and acts as a standard slave device on the I2C bus. The main + address is mandatory, others are optional and revert to defaults if not + specified. + The ADV7511 supports a large number of input data formats that differ by their color depth, color format, clock mode, bit justification and random @@ -70,6 +76,9 @@ Optional properties: rather than generate its own timings for HDMI output. - clocks: from common clock binding: reference to the CEC clock. - clock-names: from common clock binding: must be "cec". +- reg-names : Names of maps with programmable addresses. + It can contain any map needing a non-default address. + Possible maps names are : "main", "edid", "cec", "packet" Required nodes: @@ -88,7 +97,12 @@ Example adv7511w: hdmi@39 { compatible = "adi,adv7511w"; - reg = <39>; + /* + * The EDID page will be accessible on address 0x66 on the I2C + * bus. All other maps continue to use their default addresses. + */ + reg = <0x39>, <0x66>; + reg-names = "main", "edid"; interrupt-parent = <&gpio3>; interrupts = <29 IRQ_TYPE_EDGE_FALLING>; clocks = <&cec_clock>; diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt new file mode 100644 index 000000000000..f5725bb6c61c --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt @@ -0,0 +1,133 @@ +Cadence DSI bridge +================== + +The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes. + +Required properties: +- compatible: should be set to "cdns,dsi". +- reg: physical base address and length of the controller's registers. +- interrupts: interrupt line connected to the DSI bridge. +- clocks: DSI bridge clocks. +- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk". +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy". +- #address-cells: must be set to 1. +- #size-cells: must be set to 0. + +Optional properties: +- resets: DSI reset lines. +- reset-names: can contain "dsi_p_rst". + +Required subnodes: +- ports: Ports as described in Documentation/devicetree/bindings/graph.txt. + 2 ports are available: + * port 0: this port is only needed if some of your DSI devices are + controlled through an external bus like I2C or SPI. Can have at + most 4 endpoints. The endpoint number is directly encoding the + DSI virtual channel used by this device. + * port 1: represents the DPI input. + Other ports will be added later to support the new kind of inputs. + +- one subnode per DSI device connected on the DSI bus. Each DSI device should + contain a reg property encoding its virtual channel. + +Cadence DPHY +============ + +Cadence DPHY block. + +Required properties: +- compatible: should be set to "cdns,dphy". +- reg: physical base address and length of the DPHY registers. +- clocks: DPHY reference clocks. +- clock-names: must contain "psm" and "pll_ref". +- #phy-cells: must be set to 0. + + +Example: + dphy0: dphy@fd0e0000{ + compatible = "cdns,dphy"; + reg = <0x0 0xfd0e0000 0x0 0x1000>; + clocks = <&psm_clk>, <&pll_ref_clk>; + clock-names = "psm", "pll_ref"; + #phy-cells = <0>; + }; + + dsi0: dsi@fd0c0000 { + compatible = "cdns,dsi"; + reg = <0x0 0xfd0c0000 0x0 0x1000>; + clocks = <&pclk>, <&sysclk>; + clock-names = "dsi_p_clk", "dsi_sys_clk"; + interrupts = <1>; + phys = <&dphy0>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + dsi0_dpi_input: endpoint { + remote-endpoint = <&xxx_dpi_output>; + }; + }; + }; + + panel: dsi-dev@0 { + compatible = "<vendor,panel>"; + reg = <0>; + }; + }; + +or + + dsi0: dsi@fd0c0000 { + compatible = "cdns,dsi"; + reg = <0x0 0xfd0c0000 0x0 0x1000>; + clocks = <&pclk>, <&sysclk>; + clock-names = "dsi_p_clk", "dsi_sys_clk"; + interrupts = <1>; + phys = <&dphy1>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + dsi0_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&dsi_panel_input>; + }; + }; + + port@1 { + reg = <1>; + dsi0_dpi_input: endpoint { + remote-endpoint = <&xxx_dpi_output>; + }; + }; + }; + }; + + i2c@xxx { + panel: panel@59 { + compatible = "<vendor,panel>"; + reg = <0x59>; + + port { + dsi_panel_input: endpoint { + remote-endpoint = <&dsi0_output>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index 3a72a103a18a..a41d280c3f9f 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -14,6 +14,7 @@ Required properties: - compatible : Shall contain one or more of - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX + - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX When compatible with generic versions, nodes must list the SoC-specific diff --git a/Documentation/devicetree/bindings/display/bridge/tda998x.txt b/Documentation/devicetree/bindings/display/bridge/tda998x.txt index 24cc2466185a..f5a02f61dd36 100644 --- a/Documentation/devicetree/bindings/display/bridge/tda998x.txt +++ b/Documentation/devicetree/bindings/display/bridge/tda998x.txt @@ -27,7 +27,10 @@ Optional properties: in question is used. The implementation allows one or two DAIs. If two DAIs are defined, they must be of different type. -[1] Documentation/sound/alsa/soc/DAI.txt + - nxp,calib-gpios: calibration GPIO, which must correspond with the + gpio used for the TDA998x interrupt pin. + +[1] Documentation/sound/soc/dai.rst [2] include/dt-bindings/display/tda998x.h Example: diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt new file mode 100644 index 000000000000..37f0c04d5a28 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt @@ -0,0 +1,60 @@ +Thine Electronics THC63LVD1024 LVDS decoder +------------------------------------------- + +The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS streams +to parallel data outputs. The chip supports single/dual input/output modes, +handling up to two LVDS input streams and up to two digital CMOS/TTL outputs. + +Single or dual operation mode, output data mapping and DDR output modes are +configured through input signals and the chip does not expose any control bus. + +Required properties: +- compatible: Shall be "thine,thc63lvd1024" +- vcc-supply: Power supply for TTL output, TTL CLOCKOUT signal, LVDS input, + PPL and digital circuitry + +Optional properties: +- powerdown-gpios: Power down GPIO signal, pin name "/PDWN". Active low +- oe-gpios: Output enable GPIO signal, pin name "OE". Active high + +The THC63LVD1024 video port connections are modeled according +to OF graph bindings specified by Documentation/devicetree/bindings/graph.txt + +Required video port nodes: +- port@0: First LVDS input port +- port@2: First digital CMOS/TTL parallel output + +Optional video port nodes: +- port@1: Second LVDS input port +- port@3: Second digital CMOS/TTL parallel output + +Example: +-------- + + thc63lvd1024: lvds-decoder { + compatible = "thine,thc63lvd1024"; + + vcc-supply = <®_lvds_vcc>; + powerdown-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_dec_in_0: endpoint { + remote-endpoint = <&lvds_out>; + }; + }; + + port@2{ + reg = <2>; + + lvds_dec_out_2: endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt index fc2588292a68..775193e1c641 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -19,7 +19,8 @@ Required properties: clock-names property. - clock-names: list of clock names sorted in the same order as the clocks property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x", - "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", + "aclk_xiu_decon0x", "pclk_smmu_decon0x", "aclk_smmu_decon1x", + "aclk_xiu_decon1x", "pclk_smmu_decon1x", clk_decon_vclk", "sclk_decon_eclk" - ports: contains a port which is connected to mic node. address-cells and size-cells must 1 and 0, respectively. @@ -34,10 +35,14 @@ decon: decon@13800000 { clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>, <&cmu_disp CLK_ACLK_XIU_DECON0X>, <&cmu_disp CLK_PCLK_SMMU_DECON0X>, + <&cmu_disp CLK_ACLK_SMMU_DECON1X>, + <&cmu_disp CLK_ACLK_XIU_DECON1X>, + <&cmu_disp CLK_PCLK_SMMU_DECON1X>, <&cmu_disp CLK_SCLK_DECON_VCLK>, <&cmu_disp CLK_SCLK_DECON_ECLK>; clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", - "pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk"; + "pclk_smmu_decon0x", "aclk_smmu_decon1x", "aclk_xiu_decon1x", + "pclk_smmu_decon1x", "sclk_decon_vclk", "sclk_decon_eclk"; interrupt-names = "vsync", "lcd_sys"; interrupts = <0 202 0>, <0 203 0>; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index c9cd17f99702..7c6854bd0a04 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -13,6 +13,7 @@ Required Properties: - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU + - "renesas,du-r8a77965" for R8A77965 (R-Car M3-N) compatible DU - "renesas,du-r8a77970" for R8A77970 (R-Car V3M) compatible DU - "renesas,du-r8a77995" for R8A77995 (R-Car D3) compatible DU @@ -47,20 +48,21 @@ bindings specified in Documentation/devicetree/bindings/graph.txt. The following table lists for each supported model the port number corresponding to each DU output. - Port0 Port1 Port2 Port3 + Port0 Port1 Port2 Port3 ----------------------------------------------------------------------------- - R8A7743 (RZ/G1M) DPAD 0 LVDS 0 - - - R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - - R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - - R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - - R8A7791 (R-Car M2-W) DPAD 0 LVDS 0 - - - R8A7792 (R-Car V2H) DPAD 0 DPAD 1 - - - R8A7793 (R-Car M2-N) DPAD 0 LVDS 0 - - - R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - - R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 - R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - - R8A77970 (R-Car V3M) DPAD 0 LVDS 0 - - - R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - + R8A7743 (RZ/G1M) DPAD 0 LVDS 0 - - + R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - + R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - + R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - + R8A7791 (R-Car M2-W) DPAD 0 LVDS 0 - - + R8A7792 (R-Car V2H) DPAD 0 DPAD 1 - - + R8A7793 (R-Car M2-N) DPAD 0 LVDS 0 - - + R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - + R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 + R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - + R8A77965 (R-Car M3-N) DPAD 0 HDMI 0 LVDS 0 - + R8A77970 (R-Car V3M) DPAD 0 LVDS 0 - - + R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - Example: R8A7795 (R-Car H3) ES2.0 DU diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt new file mode 100644 index 000000000000..6a6cf5de08b0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt @@ -0,0 +1,93 @@ +Allwinner A31 DSI Encoder +========================= + +The DSI pipeline consists of two separate blocks: the DSI controller +itself, and its associated D-PHY. + +DSI Encoder +----------- + +The DSI Encoder generates the DSI signal from the TCON's. + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-mipi-dsi + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the DSI encoder + * bus: the DSI interface clock + * mod: the DSI module clock + - clock-names: the clock names mentioned above + - phys: phandle to the D-PHY + - phy-names: must be "dphy" + - resets: phandle to the reset controller driving the encoder + + - ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint, usually coming from the + associated TCON. + +Any MIPI-DSI device attached to this should be described according to +the bindings defined in ../mipi-dsi-bus.txt + +D-PHY +----- + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-mipi-dphy + - reg: base address and size of memory-mapped region + - clocks: phandles to the clocks feeding the DSI encoder + * bus: the DSI interface clock + * mod: the DSI module clock + - clock-names: the clock names mentioned above + - resets: phandle to the reset controller driving the encoder + +Example: + +dsi0: dsi@1ca0000 { + compatible = "allwinner,sun6i-a31-mipi-dsi"; + reg = <0x01ca0000 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_SCLK>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + phys = <&dphy0>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "bananapi,lhr050h41", "ilitek,ili9881c"; + reg = <0>; + power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */ + reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */ + backlight = <&pwm_bl>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsi0_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_dsi0>; + }; + }; + }; +}; + +dphy0: d-phy@1ca1000 { + compatible = "allwinner,sun6i-a31-mipi-dphy"; + reg = <0x01ca1000 0x1000>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_DPHY>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/dma/k3dma.txt b/Documentation/devicetree/bindings/dma/k3dma.txt index 23f8d712c3ce..4945aeac4dc4 100644 --- a/Documentation/devicetree/bindings/dma/k3dma.txt +++ b/Documentation/devicetree/bindings/dma/k3dma.txt @@ -23,7 +23,6 @@ Controller: dma-requests = <27>; interrupts = <0 12 4>; clocks = <&pclk>; - status = "disable"; }; Client: diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 61315eaa7660..b1ba639554c0 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -29,6 +29,7 @@ Required Properties: - "renesas,dmac-r8a77965" (R-Car M3-N) - "renesas,dmac-r8a77970" (R-Car V3M) - "renesas,dmac-r8a77980" (R-Car V3H) + - "renesas,dmac-r8a77995" (R-Car D3) - reg: base address and length of the registers block for the DMAC diff --git a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt index 9dc935e24e55..482e54362d3e 100644 --- a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt @@ -12,6 +12,8 @@ Required Properties: - "renesas,r8a7795-usb-dmac" (R-Car H3) - "renesas,r8a7796-usb-dmac" (R-Car M3-W) - "renesas,r8a77965-usb-dmac" (R-Car M3-N) + - "renesas,r8a77990-usb-dmac" (R-Car E3) + - "renesas,r8a77995-usb-dmac" (R-Car D3) - reg: base address and length of the registers block for the DMAC - interrupts: interrupt specifiers for the DMAC, one for each entry in interrupt-names. diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 66026dcf53e1..3f15f6644527 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -190,7 +190,6 @@ mmc0: mmc@23000000 { power-domains = <&k2g_pds 0xb>; clocks = <&k2g_clks 0xb 1>, <&k2g_clks 0xb 2>; clock-names = "fck", "mmchsdb_fck"; - status = "disabled"; }; ------------------------------------------------------------------------------ diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt index 4a1714f96bab..5626560a6cfd 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt +++ b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt @@ -231,3 +231,38 @@ Example: <48 IRQ_TYPE_LEVEL_HIGH>; }; }; + +Stratix10 SoCFPGA ECC Manager +The Stratix10 SoC ECC Manager handles the IRQs for each peripheral +in a shared register similar to the Arria10. However, ECC requires +access to registers that can only be read from Secure Monitor with +SMC calls. Therefore the device tree is slightly different. + +Required Properties: +- compatible : Should be "altr,socfpga-s10-ecc-manager" +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. +- interrupt-controller : boolean indicator that ECC Manager is an interrupt controller +- #interrupt-cells : must be set to 2. + +Subcomponents: + +SDRAM ECC +Required Properties: +- compatible : Should be "altr,sdram-edac-s10" +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +Example: + + eccmgr { + compatible = "altr,socfpga-s10-ecc-manager"; + interrupts = <0 15 4>, <0 95 4>; + interrupt-controller; + #interrupt-cells = <2>; + + sdramedac { + compatible = "altr,sdram-edac-s10"; + interrupts = <16 4>, <48 4>; + }; + }; diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt index 7b40054be0d8..fcf6979c0b6d 100644 --- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt @@ -11,9 +11,10 @@ Required properties: * "qcom,scm-msm8660" for MSM8660 platforms * "qcom,scm-msm8690" for MSM8690 platforms * "qcom,scm-msm8996" for MSM8996 platforms + * "qcom,scm-ipq4019" for IPQ4019 platforms * "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc) - clocks: One to three clocks may be required based on compatible. - * No clock required for "qcom,scm-msm8996" + * No clock required for "qcom,scm-msm8996", "qcom,scm-ipq4019" * Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960" * Core, iface, and bus clocks required for "qcom,scm" - clock-names: Must contain "core" for the core clock, "iface" for the interface diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt new file mode 100644 index 000000000000..a8c362eb160c --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt @@ -0,0 +1,29 @@ +Lattice MachXO2 Slave SPI FPGA Manager + +Lattice MachXO2 FPGAs support a method of loading the bitstream over +'slave SPI' interface. + +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com + +Required properties: +- compatible: should contain "lattice,machxo2-slave-spi" +- reg: spi chip select of the FPGA + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@2000 { + ... + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "lattice,machxo2-slave-spi"; + spi-max-frequency = <8000000>; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt index a767259dedad..1e442450747f 100644 --- a/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt +++ b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt @@ -11,6 +11,10 @@ Optional properties: - trans-gpios = <gpio-descriptor>; : GPIO for voltage translator enable - mux-gpios = <gpio-descriptor>; : GPIO for pin multiplexing with other functions (eg, external FSI masters) + - no-gpio-delays; : Don't add extra delays between GPIO + accesses. This is useful when the HW + GPIO block is running at a low enough + frequency. Examples: diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index d2a937682836..88f228665507 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -31,10 +31,15 @@ Required properties: ti,tca9554 onnn,pca9654 exar,xra1202 + - gpio-controller: if used as gpio expander. + - #gpio-cells: if used as gpio expander. + - interrupt-controller: if to be used as interrupt expander. + - #interrupt-cells: if to be used as interrupt expander. Optional properties: - reset-gpios: GPIO specification for the RESET input. This is an active low signal to the PCA953x. + - vcc-supply: power supply regulator. Example: @@ -47,3 +52,32 @@ Example: interrupt-parent = <&gpio3>; interrupts = <23 IRQ_TYPE_LEVEL_LOW>; }; + + +Example with Interrupts: + + + gpio99: gpio@22 { + compatible = "nxp,pcal6524"; + reg = <0x22>; + interrupt-parent = <&gpio6>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; /* gpio6_161 */ + interrupt-controller; + #interrupt-cells = <2>; + vcc-supply = <&vdds_1v8_main>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "hdmi-ct-hpd", "hdmi.ls-oe", "p02", "p03", "vibra", "fault2", "p06", "p07", + "en-usb", "en-host1", "en-host2", "chg-int", "p14", "p15", "mic-int", "en-modem", + "shdn-hs-amp", "chg-status+red", "green", "blue", "en-esata", "fault1", "p26", "p27"; + }; + + ts3a227@3b { + compatible = "ti,ts3a227e"; + reg = <0x3b>; + interrupt-parent = <&gpio99>; + interrupts = <14 IRQ_TYPE_EDGE_RISING>; + ti,micbias = <0>; /* 2.1V */ + }; + diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 9474138d776e..378f1322211e 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -5,6 +5,7 @@ Required Properties: - compatible: should contain one or more of the following: - "renesas,gpio-r8a7743": for R8A7743 (RZ/G1M) compatible GPIO controller. - "renesas,gpio-r8a7745": for R8A7745 (RZ/G1E) compatible GPIO controller. + - "renesas,gpio-r8a77470": for R8A77470 (RZ/G1C) compatible GPIO controller. - "renesas,gpio-r8a7778": for R8A7778 (R-Car M1) compatible GPIO controller. - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. @@ -14,7 +15,9 @@ Required Properties: - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. - "renesas,gpio-r8a7796": for R8A7796 (R-Car M3-W) compatible GPIO controller. + - "renesas,gpio-r8a77965": for R8A77965 (R-Car M3-N) compatible GPIO controller. - "renesas,gpio-r8a77970": for R8A77970 (R-Car V3M) compatible GPIO controller. + - "renesas,gpio-r8a77990": for R8A77990 (R-Car E3) compatible GPIO controller. - "renesas,gpio-r8a77995": for R8A77995 (R-Car D3) compatible GPIO controller. - "renesas,rcar-gen1-gpio": for a generic R-Car Gen1 GPIO controller. - "renesas,rcar-gen2-gpio": for a generic R-Car Gen2 or RZ/G1 GPIO controller. diff --git a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt index 4a75da7051bd..3c1118bc67f5 100644 --- a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt @@ -26,8 +26,13 @@ controller. the second encodes the triger flags encoded as described in Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - interrupt-parent : The parent interrupt controller. -- interrupts : The interrupt to the parent controller raised when GPIOs - generate the interrupts. +- interrupts : The interrupts to the parent controller raised when GPIOs + generate the interrupts. If the controller provides one combined interrupt + for all GPIOs, specify a single interrupt. If the controller provides one + interrupt for each GPIO, provide a list of interrupts that correspond to each + of the GPIO pins. When specifying multiple interrupts, if any are unconnected, + use the interrupts-extended property to specify the interrupts and set the + interrupt controller handle for unused interrupts to 0. - snps,nr-gpios : The number of pins in the port, a single cell. - resets : Reset line for the controller. diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt index 039219df05c5..18a2cde2e5f3 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt @@ -34,7 +34,7 @@ Optional properties: - mali-supply : Phandle to regulator for the Mali device. Refer to Documentation/devicetree/bindings/regulator/regulator.txt for details. -- operating-points-v2 : Refer to Documentation/devicetree/bindings/power/opp.txt +- operating-points-v2 : Refer to Documentation/devicetree/bindings/opp/opp.txt for details. diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index c1f65d1dac1d..63cd91176a68 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -44,7 +44,7 @@ Optional properties: - memory-region: Memory region to allocate from, as defined in - Documentation/devicetree/bindi/reserved-memory/reserved-memory.txt + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt - mali-supply: Phandle to regulator for the Mali device, as defined in diff --git a/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt new file mode 100644 index 000000000000..c907aa8dd755 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt @@ -0,0 +1,28 @@ +Broadcom V3D GPU + +Only the Broadcom V3D 3.x and newer GPUs are covered by this binding. +For V3D 2.x, see brcm,bcm-vc4.txt. + +Required properties: +- compatible: Should be "brcm,7268-v3d" or "brcm,7278-v3d" +- reg: Physical base addresses and lengths of the register areas +- reg-names: Names for the register areas. The "hub", "bridge", and "core0" + register areas are always required. The "gca" register area + is required if the GCA cache controller is present. +- interrupts: The interrupt numbers. The first interrupt is for the hub, + while the following interrupts are for the cores. + See bindings/interrupt-controller/interrupts.txt + +Optional properties: +- clocks: The core clock the unit runs on + +v3d { + compatible = "brcm,7268-v3d"; + reg = <0xf1204000 0x100>, + <0xf1200000 0x4000>, + <0xf1208000 0x4000>, + <0xf1204100 0x100>; + reg-names = "bridge", "hub", "core0", "gca"; + interrupts = <0 78 4>, + <0 77 4>; +}; diff --git a/Documentation/devicetree/bindings/gpu/samsung-scaler.txt b/Documentation/devicetree/bindings/gpu/samsung-scaler.txt new file mode 100644 index 000000000000..9c3d98105dfd --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/samsung-scaler.txt @@ -0,0 +1,27 @@ +* Samsung Exynos Image Scaler + +Required properties: + - compatible : value should be one of the following: + (a) "samsung,exynos5420-scaler" for Scaler IP in Exynos5420 + (b) "samsung,exynos5433-scaler" for Scaler IP in Exynos5433 + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : Interrupt specifier for scaler interrupt, according to format + specific to interrupt parent. + + - clocks : Clock specifier for scaler clock, according to generic clock + bindings. (See Documentation/devicetree/bindings/clock/exynos*.txt) + + - clock-names : Names of clocks. For exynos scaler, it should be "mscl" + on 5420 and "pclk", "aclk" and "aclk_xiu" on 5433. + +Example: + scaler@12800000 { + compatible = "samsung,exynos5420-scaler"; + reg = <0x12800000 0x1294>; + interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_MSCL0>; + clock-names = "mscl"; + }; diff --git a/Documentation/devicetree/bindings/hwmon/gpio-fan.txt b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt index 439a7430fc68..2becdcfdc840 100644 --- a/Documentation/devicetree/bindings/hwmon/gpio-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt @@ -11,7 +11,7 @@ Optional properties: must have the RPM values in ascending order. - alarm-gpios: This pin going active indicates something is wrong with the fan, and a udev event will be fired. -- cooling-cells: If used as a cooling device, must be <2> +- #cooling-cells: If used as a cooling device, must be <2> Also see: Documentation/devicetree/bindings/thermal/thermal.txt min and max states are derived from the speed-map of the fan. diff --git a/Documentation/devicetree/bindings/hwmon/ltc2990.txt b/Documentation/devicetree/bindings/hwmon/ltc2990.txt new file mode 100644 index 000000000000..f92f54029e84 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltc2990.txt @@ -0,0 +1,36 @@ +ltc2990: Linear Technology LTC2990 power monitor + +Required properties: +- compatible: Must be "lltc,ltc2990" +- reg: I2C slave address +- lltc,meas-mode: + An array of two integers for configuring the chip measurement mode. + + The first integer defines the bits 2..0 in the control register. In all + cases the internal temperature and supply voltage are measured. In + addition the following input measurements are enabled per mode: + + 0: V1, V2, TR2 + 1: V1-V2, TR2 + 2: V1-V2, V3, V4 + 3: TR1, V3, V4 + 4: TR1, V3-V4 + 5: TR1, TR2 + 6: V1-V2, V3-V4 + 7: V1, V2, V3, V4 + + The second integer defines the bits 4..3 in the control register. This + allows a subset of the measurements to be enabled: + + 0: Internal temperature and supply voltage only + 1: TR1, V1 or V1-V2 only per mode + 2: TR2, V3 or V3-V4 only per mode + 3: All measurements per mode + +Example: + +ltc2990@4c { + compatible = "lltc,ltc2990"; + reg = <0x4c>; + lltc,meas-mode = <7 3>; /* V1, V2, V3, V4 */ +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt index 64e6e656c345..b745f3706120 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt @@ -24,7 +24,7 @@ Recommended properties : - clock-frequency : desired I2C bus clock frequency in Hz. - ti,has-pfunc: boolean; if defined, it indicates that SoC supports PFUNC registers. PFUNC registers allow to switch I2C pins to function as - GPIOs, so they can by toggled manually. + GPIOs, so they can be toggled manually. Example (enbw_cmc board): i2c@1c22000 { diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 4a7811ecd954..7ce8fae55537 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -15,6 +15,7 @@ Required properties: "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. "renesas,i2c-r8a77965" if the device is a part of a R8A77965 SoC. "renesas,i2c-r8a77970" if the device is a part of a R8A77970 SoC. + "renesas,i2c-r8a77980" if the device is a part of a R8A77980 SoC. "renesas,i2c-r8a77995" if the device is a part of a R8A77995 SoC. "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index 89b3250f049b..66ae46d3bc2f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -8,9 +8,7 @@ Required properties: (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used inside HDMIPHY block found on several samsung SoCs - (d) "samsung, exynos5440-i2c", for s3c2440-like i2c used - on EXYNOS5440 which does not need GPIO configuration. - (e) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as + (d) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as a host to SATA PHY controller on an internal bus. - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt index 1e6ee3deb4fa..d1acd5ea2737 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -7,6 +7,7 @@ Required properties: - "amlogic,meson-gxbb-saradc" for GXBB - "amlogic,meson-gxl-saradc" for GXL - "amlogic,meson-gxm-saradc" for GXM + - "amlogic,meson-axg-saradc" for AXG along with the generic "amlogic,meson-saradc" - reg: the physical base address and length of the registers - interrupts: the interrupt indicating end of sampling diff --git a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt index 7d64753df949..56373d643f76 100644 --- a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt +++ b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt @@ -49,7 +49,7 @@ Required properties: Examples: spi_controller { mcp3x0x@0 { - compatible = "mcp3002"; + compatible = "microchip,mcp3002"; reg = <0>; spi-max-frequency = <1000000>; vref-supply = <&vref_reg>; diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt index 6c49db7f8ad2..6c49db7f8ad2 100644 --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt index e8bb8243e92c..f1ead43a1a95 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -24,8 +24,11 @@ Required properties: - compatible: Should be one of: "st,stm32f4-adc-core" "st,stm32h7-adc-core" + "st,stm32mp1-adc-core" - reg: Offset and length of the ADC block register set. -- interrupts: Must contain the interrupt for ADC block. +- interrupts: One or more interrupts for ADC block. Some parts like stm32f4 + and stm32h7 share a common ADC interrupt line. stm32mp1 has two separate + interrupt lines, one for each ADC within ADC block. - clocks: Core can use up to two clocks, depending on part used: - "adc" clock: for the analog circuitry, common to all ADCs. It's required on stm32f4. @@ -53,6 +56,7 @@ Required properties: - compatible: Should be one of: "st,stm32f4-adc" "st,stm32h7-adc" + "st,stm32mp1-adc" - reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200). - clocks: Input clock private to this ADC instance. It's required only on stm32f4, that has per instance clock input for registers access. diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt index ed7520d1d051..75ba25d062e1 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt @@ -8,14 +8,16 @@ It is mainly targeted for: - PDM microphones (audio digital microphone) It features up to 8 serial digital interfaces (SPI or Manchester) and -up to 4 filters on stm32h7. +up to 4 filters on stm32h7 or 6 filters on stm32mp1. Each child node match with a filter instance. Contents of a STM32 DFSDM root node: ------------------------------------ Required properties: -- compatible: Should be "st,stm32h7-dfsdm". +- compatible: Should be one of: + "st,stm32h7-dfsdm" + "st,stm32mp1-dfsdm" - reg: Offset and length of the DFSDM block register set. - clocks: IP and serial interfaces clocking. Should be set according to rcc clock ID and "clock-names". @@ -45,6 +47,7 @@ Required properties: "st,stm32-dfsdm-adc" for sigma delta ADCs "st,stm32-dfsdm-dmic" for audio digital microphone. - reg: Specifies the DFSDM filter instance used. + Valid values are from 0 to 3 on stm32h7, 0 to 5 on stm32mp1. - interrupts: IRQ lines connected to each DFSDM filter instance. - st,adc-channels: List of single-ended channels muxed for this ADC. valid values: diff --git a/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.txt b/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.txt new file mode 100644 index 000000000000..821b61b8c542 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.txt @@ -0,0 +1,26 @@ +Current Sense Amplifier +======================= + +When an io-channel measures the output voltage from a current sense +amplifier, the interesting measurement is almost always the current +through the sense resistor, not the voltage output. This binding +describes such a current sense circuit. + +Required properties: +- compatible : "current-sense-amplifier" +- io-channels : Channel node of a voltage io-channel. +- sense-resistor-micro-ohms : The sense resistance in microohms. + +Optional properties: +- sense-gain-mult: Amplifier gain multiplier. The default is <1>. +- sense-gain-div: Amplifier gain divider. The default is <1>. + +Example: + +sysi { + compatible = "current-sense-amplifier"; + io-channels = <&tiadc 0>; + + sense-resistor-micro-ohms = <20000>; + sense-gain-mul = <50>; +}; diff --git a/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.txt b/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.txt new file mode 100644 index 000000000000..0f67108a07b6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/afe/current-sense-shunt.txt @@ -0,0 +1,41 @@ +Current Sense Shunt +=================== + +When an io-channel measures the voltage over a current sense shunt, +the interesting measurement is almost always the current through the +shunt, not the voltage over it. This binding describes such a current +sense circuit. + +Required properties: +- compatible : "current-sense-shunt" +- io-channels : Channel node of a voltage io-channel. +- shunt-resistor-micro-ohms : The shunt resistance in microohms. + +Example: +The system current is measured by measuring the voltage over a +3.3 ohms shunt resistor. + +sysi { + compatible = "current-sense-shunt"; + io-channels = <&tiadc 0>; + + /* Divide the voltage by 3300000/1000000 (or 3.3) for the current. */ + shunt-resistor-micro-ohms = <3300000>; +}; + +&i2c { + tiadc: adc@48 { + compatible = "ti,ads1015"; + reg = <0x48>; + #io-channel-cells = <1>; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { /* IN0,IN1 differential */ + reg = <0>; + ti,gain = <1>; + ti,datarate = <4>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/afe/voltage-divider.txt b/Documentation/devicetree/bindings/iio/afe/voltage-divider.txt new file mode 100644 index 000000000000..b452a8406107 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/afe/voltage-divider.txt @@ -0,0 +1,53 @@ +Voltage divider +=============== + +When an io-channel measures the midpoint of a voltage divider, the +interesting voltage is often the voltage over the full resistance +of the divider. This binding describes the voltage divider in such +a curcuit. + + Vin ----. + | + .-----. + | R | + '-----' + | + +---- Vout + | + .-----. + | Rout| + '-----' + | + GND + +Required properties: +- compatible : "voltage-divider" +- io-channels : Channel node of a voltage io-channel measuring Vout. +- output-ohms : Resistance Rout over which the output voltage is measured. + See full-ohms. +- full-ohms : Resistance R + Rout for the full divider. The io-channel + is scaled by the Rout / (R + Rout) quotient. + +Example: +The system voltage is circa 12V, but divided down with a 22/222 +voltage divider (R = 200 Ohms, Rout = 22 Ohms) and fed to an ADC. + +sysv { + compatible = "voltage-divider"; + io-channels = <&maxadc 1>; + + /* Scale the system voltage by 22/222 to fit the ADC range. */ + output-ohms = <22>; + full-ohms = <222>; /* 200 + 22 */ +}; + +&spi { + maxadc: adc@0 { + compatible = "maxim,max1027"; + reg = <0>; + #io-channel-cells = <1>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <1000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/ltc2632.txt b/Documentation/devicetree/bindings/iio/dac/ltc2632.txt index eb911e5a8ab4..e0d5fea33031 100644 --- a/Documentation/devicetree/bindings/iio/dac/ltc2632.txt +++ b/Documentation/devicetree/bindings/iio/dac/ltc2632.txt @@ -12,12 +12,26 @@ Required properties: Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt apply. In particular, "reg" and "spi-max-frequency" properties must be given. +Optional properties: + - vref-supply: Phandle to the external reference voltage supply. This should + only be set if there is an external reference voltage connected to the VREF + pin. If the property is not set the internal reference is used. + Example: + vref: regulator-vref { + compatible = "regulator-fixed"; + regulator-name = "vref-ltc2632"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + }; + spi_master { dac: ltc2632@0 { compatible = "lltc,ltc2632-l12"; reg = <0>; /* CS0 */ spi-max-frequency = <1000000>; + vref-supply = <&vref>; /* optional */ }; }; diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac5571.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac5571.txt new file mode 100644 index 000000000000..03af6b9a4d07 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac5571.txt @@ -0,0 +1,24 @@ +* Texas Instruments DAC5571 Family + +Required properties: + - compatible: Should contain + "ti,dac5571" + "ti,dac6571" + "ti,dac7571" + "ti,dac5574" + "ti,dac6574" + "ti,dac7574" + "ti,dac5573" + "ti,dac6573" + "ti,dac7573" + - reg: Should contain the DAC I2C address + +Optional properties: + - vref-supply: The regulator supply for DAC reference voltage + +Example: +dac@0 { + compatible = "ti,dac5571"; + reg = <0x4C>; + vref-supply = <&vdd_supply>; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt index 2b4514592f83..5f4777e8cc9e 100644 --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -8,10 +8,16 @@ Required properties: "invensense,mpu6500" "invensense,mpu9150" "invensense,mpu9250" + "invensense,mpu9255" "invensense,icm20608" - reg : the I2C address of the sensor - interrupt-parent : should be the phandle for the interrupt controller - - interrupts : interrupt mapping for GPIO IRQ + - interrupts: interrupt mapping for IRQ. It should be configured with flags + IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or + IRQ_TYPE_EDGE_FALLING. + + Refer to interrupt-controller/interrupts.txt for generic interrupt client node + bindings. Optional properties: - mount-matrix: an optional 3x3 mounting rotation matrix @@ -24,7 +30,7 @@ Example: compatible = "invensense,mpu6050"; reg = <0x68>; interrupt-parent = <&gpio1>; - interrupts = <18 1>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>; mount-matrix = "-0.984807753012208", /* x0 */ "0", /* y0 */ "-0.173648177666930", /* z0 */ @@ -41,7 +47,7 @@ Example: compatible = "invensense,mpu9250"; reg = <0x68>; interrupt-parent = <&gpio3>; - interrupts = <21 1>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; i2c-gate { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt index 1ff1af799c76..ef8a8566c63f 100644 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -6,6 +6,7 @@ Required properties: "st,lsm6ds3h" "st,lsm6dsl" "st,lsm6dsm" + "st,ism330dlc" - reg: i2c address of the sensor / spi cs line Optional properties: diff --git a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt index b9b621e94cd7..e6d0c2eb345c 100644 --- a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt +++ b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt @@ -1,10 +1,13 @@ -* Texas Instruments LMP91000 potentiostat +* Texas Instruments LMP91000 series of potentiostats -http://www.ti.com/lit/ds/symlink/lmp91000.pdf +LMP91000: http://www.ti.com/lit/ds/symlink/lmp91000.pdf +LMP91002: http://www.ti.com/lit/ds/symlink/lmp91002.pdf Required properties: - - compatible: should be "ti,lmp91000" + - compatible: should be one of the following: + "ti,lmp91000" + "ti,lmp91002" - reg: the I2C address of the device - io-channels: the phandle of the iio provider diff --git a/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt b/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt new file mode 100644 index 000000000000..2888d07c2ef0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt @@ -0,0 +1,43 @@ +MediaTek MT6397/MT6323 PMIC Keys Device Driver + +There are two key functions provided by MT6397/MT6323 PMIC, pwrkey +and homekey. The key functions are defined as the subnode of the function +node provided by MT6397/MT6323 PMIC that is being defined as one kind +of Muti-Function Device (MFD) + +For MT6397/MT6323 MFD bindings see: +Documentation/devicetree/bindings/mfd/mt6397.txt + +Required properties: +- compatible: "mediatek,mt6397-keys" or "mediatek,mt6323-keys" +- linux,keycodes: See Documentation/devicetree/bindings/input/keys.txt + +Optional Properties: +- wakeup-source: See Documentation/devicetree/bindings/power/wakeup-source.txt +- mediatek,long-press-mode: Long press key shutdown setting, 1 for + pwrkey only, 2 for pwrkey/homekey together, others for disabled. +- power-off-time-sec: See Documentation/devicetree/bindings/input/keys.txt + +Example: + + pmic: mt6397 { + compatible = "mediatek,mt6397"; + + ... + + mt6397keys: mt6397keys { + compatible = "mediatek,mt6397-keys"; + mediatek,long-press-mode = <1>; + power-off-time-sec = <0>; + + power { + linux,keycodes = <116>; + wakeup-source; + }; + + home { + linux,keycodes = <114>; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt index f2c30c8b725d..9afffbdf6e28 100644 --- a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt @@ -12,7 +12,7 @@ Additional documentation for F11 can be found at: http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf Optional Touch Properties: -Description in Documentation/devicetree/bindings/input/touch +Description in Documentation/devicetree/bindings/input/touchscreen - touchscreen-inverted-x - touchscreen-inverted-y - touchscreen-swapped-x-y diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt index f99fe5cdeaec..a644408b33b8 100644 --- a/Documentation/devicetree/bindings/input/rotary-encoder.txt +++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt @@ -28,7 +28,7 @@ Deprecated properties: This property is deprecated. Instead, a 'steps-per-period ' value should be used, such as "rotary-encoder,steps-per-period = <2>". -See Documentation/input/rotary-encoder.txt for more information. +See Documentation/input/devices/rotary-encoder.rst for more information. Example: diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt index a83f9a5734ca..89674ad8a097 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -9,11 +9,12 @@ number of interrupt exposed depends on the SoC. Required properties: -- compatible : must have "amlogic,meson8-gpio-intc” and either - “amlogic,meson8-gpio-intc” for meson8 SoCs (S802) or - “amlogic,meson8b-gpio-intc” for meson8b SoCs (S805) or - “amlogic,meson-gxbb-gpio-intc” for GXBB SoCs (S905) or - “amlogic,meson-gxl-gpio-intc” for GXL SoCs (S905X, S912) +- compatible : must have "amlogic,meson8-gpio-intc" and either + "amlogic,meson8-gpio-intc" for meson8 SoCs (S802) or + "amlogic,meson8b-gpio-intc" for meson8b SoCs (S805) or + "amlogic,meson-gxbb-gpio-intc" for GXBB SoCs (S905) or + "amlogic,meson-gxl-gpio-intc" for GXL SoCs (S905X, S912) + "amlogic,meson-axg-gpio-intc" for AXG SoCs (A113D, A113X) - interrupt-parent : a phandle to the GIC the interrupts are routed to. Usually this is provided at the root level of the device tree as it is common to most of the SoC. diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 0a57f2f4167d..3ea78c4ef887 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -57,6 +57,20 @@ Optional occupied by the redistributors. Required if more than one such region is present. +- msi-controller: Boolean property. Identifies the node as an MSI + controller. Only present if the Message Based Interrupt + functionnality is being exposed by the HW, and the mbi-ranges + property present. + +- mbi-ranges: A list of pairs <intid span>, where "intid" is the first + SPI of a range that can be used an MBI, and "span" the size of that + range. Multiple ranges can be provided. Requires "msi-controller" to + be set. + +- mbi-alias: Address property. Base address of an alias of the GICD + region containing only the {SET,CLR}SPI registers to be used if + isolation is required, and if supported by the HW. + Sub-nodes: PPI affinity can be expressed as a single "ppi-partitions" node, @@ -99,6 +113,9 @@ Examples: <0x0 0x2c020000 0 0x2000>; // GICV interrupts = <1 9 4>; + msi-controller; + mbi-ranges = <256 128>; + gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt index edf03f09244b..136bd612bd83 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt @@ -5,11 +5,14 @@ Required properties: - compatible: Should be: "st,stm32-exti" "st,stm32h7-exti" + "st,stm32mp1-exti" - reg: Specifies base physical address and size of the registers - interrupt-controller: Indentifies the node as an interrupt controller - #interrupt-cells: Specifies the number of cells to encode an interrupt specifier, shall be 2 - interrupts: interrupts references to primary interrupt controller + (only needed for exti controller with multiple exti under + same parent interrupt: st,stm32-exti and st,stm32h7-exti") Example: diff --git a/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt b/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt new file mode 100644 index 000000000000..3538a214fff1 --- /dev/null +++ b/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt @@ -0,0 +1,39 @@ +* Nuvoton NPCM7xx KCS (Keyboard Controller Style) IPMI interface + +The Nuvoton SOCs (NPCM7xx) are commonly used as BMCs +(Baseboard Management Controllers) and the KCS interface can be +used to perform in-band IPMI communication with their host. + +Required properties: +- compatible : should be one of + "nuvoton,npcm750-kcs-bmc" +- interrupts : interrupt generated by the controller +- kcs_chan : The KCS channel number in the controller + +Example: + + lpc_kcs: lpc_kcs@f0007000 { + compatible = "nuvoton,npcm750-lpc-kcs", "simple-mfd", "syscon"; + reg = <0xf0007000 0x40>; + reg-io-width = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xf0007000 0x40>; + + kcs1: kcs1@0 { + compatible = "nuvoton,npcm750-kcs-bmc"; + reg = <0x0 0x40>; + interrupts = <0 9 4>; + kcs_chan = <1>; + status = "disabled"; + }; + + kcs2: kcs2@0 { + compatible = "nuvoton,npcm750-kcs-bmc"; + reg = <0x0 0x40>; + interrupts = <0 9 4>; + kcs_chan = <2>; + status = "disabled"; + }; + };
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt index 764db86d441a..310810906613 100644 --- a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt +++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt @@ -17,6 +17,10 @@ Optional properties: "pwms" property (see PWM binding[0]) - enable-gpios: contains a single GPIO specifier for the GPIO which enables and disables the backlight (see GPIO binding[1]) + - post-pwm-on-delay-ms: Delay in ms between setting an initial (non-zero) PWM + and enabling the backlight using GPIO. + - pwm-off-delay-ms: Delay in ms between disabling the backlight using GPIO + and setting PWM value to 0. [0]: Documentation/devicetree/bindings/pwm/pwm.txt [1]: Documentation/devicetree/bindings/gpio/gpio.txt @@ -32,4 +36,6 @@ Example: power-supply = <&vdd_bl_reg>; enable-gpios = <&gpio 58 0>; + post-pwm-on-delay-ms = <10>; + pwm-off-delay-ms = <10>; }; diff --git a/Documentation/devicetree/bindings/leds/backlight/zii,rave-sp-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/zii,rave-sp-backlight.txt new file mode 100644 index 000000000000..ff5c92138650 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/zii,rave-sp-backlight.txt @@ -0,0 +1,23 @@ +Zodiac Inflight Innovations RAVE Supervisory Processor Backlight Bindings + +RAVE SP backlight device is a "MFD cell" device corresponding to +backlight functionality of RAVE Supervisory Processor. It is expected +that its Device Tree node is specified as a child of the node +corresponding to the parent RAVE SP device (as documented in +Documentation/devicetree/bindings/mfd/zii,rave-sp.txt) + +Required properties: + +- compatible: Should be "zii,rave-sp-backlight" + +Example: + + rave-sp { + compatible = "zii,rave-sp-rdu1"; + current-speed = <38400>; + + backlight { + compatible = "zii,rave-sp-backlight"; + }; + } + diff --git a/Documentation/devicetree/bindings/leds/leds-cr0014114.txt b/Documentation/devicetree/bindings/leds/leds-cr0014114.txt new file mode 100644 index 000000000000..4255b19ad25c --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-cr0014114.txt @@ -0,0 +1,54 @@ +Crane Merchandising System - cr0014114 LED driver +------------------------------------------------- + +This LED Board is widely used in vending machines produced +by Crane Merchandising Systems. + +Required properties: +- compatible: "crane,cr0014114" + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. In particular, "reg" and "spi-max-frequency" properties must be given. + +LED sub-node properties: +- label : + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + +Example +------- + +led-controller@0 { + compatible = "crane,cr0014114"; + reg = <0>; + spi-max-frequency = <50000>; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + label = "red:coin"; + }; + led@1 { + reg = <1>; + label = "green:coin"; + }; + led@2 { + reg = <2>; + label = "blue:coin"; + }; + led@3 { + reg = <3>; + label = "red:bill"; + }; + led@4 { + reg = <4>; + label = "green:bill"; + }; + led@5 { + reg = <5>; + label = "blue:bill"; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/leds/leds-lm3601x.txt b/Documentation/devicetree/bindings/leds/leds-lm3601x.txt new file mode 100644 index 000000000000..a88b2c41e75b --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm3601x.txt @@ -0,0 +1,45 @@ +* Texas Instruments - lm3601x Single-LED Flash Driver + +The LM3601X are ultra-small LED flash drivers that +provide a high level of adjustability. + +Required properties: + - compatible : Can be one of the following + "ti,lm36010" + "ti,lm36011" + - reg : I2C slave address + - #address-cells : 1 + - #size-cells : 0 + +Required child properties: + - reg : 0 - Indicates a IR mode + 1 - Indicates a Torch (white LED) mode + +Required properties for flash LED child nodes: + See Documentation/devicetree/bindings/leds/common.txt + - flash-max-microamp : Range from 11mA - 1.5A + - flash-max-timeout-us : Range from 40ms - 1600ms + - led-max-microamp : Range from 2.4mA - 376mA + +Optional child properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + +Example: +led-controller@64 { + compatible = "ti,lm36010"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x64>; + + led@0 { + reg = <1>; + label = "white:torch"; + led-max-microamp = <376000>; + flash-max-microamp = <1500000>; + flash-max-timeout-us = <1600000>; + }; +} + +For more product information please see the links below: +http://www.ti.com/product/LM36010 +http://www.ti.com/product/LM36011 diff --git a/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt b/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt new file mode 100644 index 000000000000..dddf84f9c7ea --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt @@ -0,0 +1,41 @@ +LEDs connected to Spreadtrum SC27XX PMIC breathing light controller + +The SC27xx breathing light controller supports to 3 outputs: +red LED, green LED and blue LED. Each LED can work at normal +PWM mode or breath light mode. + +Required properties: +- compatible: Should be "sprd,sc2731-bltc". +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- reg: Specify the controller address. + +Required child properties: +- reg: Port this LED is connected to. + +Optional child properties: +- label: See Documentation/devicetree/bindings/leds/common.txt. + +Examples: + +led-controller@200 { + compatible = "sprd,sc2731-bltc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x200>; + + led@0 { + label = "red"; + reg = <0x0>; + }; + + led@1 { + label = "green"; + reg = <0x1>; + }; + + led@2 { + label = "blue"; + reg = <0x2>; + }; +}; diff --git a/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt b/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt index 16964f0c1773..6e8a9ab0fdae 100644 --- a/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt +++ b/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt @@ -10,6 +10,8 @@ platforms. Definition: must be one of: "qcom,msm8916-apcs-kpss-global", "qcom,msm8996-apcs-hmss-global" + "qcom,msm8998-apcs-hmss-global" + "qcom,sdm845-apss-shared" - reg: Usage: required diff --git a/Documentation/devicetree/bindings/mailbox/stm32-ipcc.txt b/Documentation/devicetree/bindings/mailbox/stm32-ipcc.txt new file mode 100644 index 000000000000..1d2b7fee7b85 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/stm32-ipcc.txt @@ -0,0 +1,47 @@ +* STMicroelectronics STM32 IPCC (Inter-Processor Communication Controller) + +The IPCC block provides a non blocking signaling mechanism to post and +retrieve messages in an atomic way between two processors. +It provides the signaling for N bidirectionnal channels. The number of channels +(N) can be read from a dedicated register. + +Required properties: +- compatible: Must be "st,stm32mp1-ipcc" +- reg: Register address range (base address and length) +- st,proc-id: Processor id using the mailbox (0 or 1) +- clocks: Input clock +- interrupt-names: List of names for the interrupts described by the interrupt + property. Must contain the following entries: + - "rx" + - "tx" + - "wakeup" +- interrupts: Interrupt specifiers for "rx channel occupied", "tx channel + free" and "system wakeup". +- #mbox-cells: Number of cells required for the mailbox specifier. Must be 1. + The data contained in the mbox specifier of the "mboxes" + property in the client node is the mailbox channel index. + +Optional properties: +- wakeup-source: Flag to indicate whether this device can wake up the system + + + +Example: + ipcc: mailbox@4c001000 { + compatible = "st,stm32mp1-ipcc"; + #mbox-cells = <1>; + reg = <0x4c001000 0x400>; + st,proc-id = <0>; + interrupts-extended = <&intc GIC_SPI 100 IRQ_TYPE_NONE>, + <&intc GIC_SPI 101 IRQ_TYPE_NONE>, + <&aiec 62 1>; + interrupt-names = "rx", "tx", "wakeup"; + clocks = <&rcc_clk IPCC>; + wakeup-source; + } + +Client: + mbox_test { + ... + mboxes = <&ipcc 0>, <&ipcc 1>; + }; diff --git a/Documentation/devicetree/bindings/marvell.txt b/Documentation/devicetree/bindings/marvell.txt deleted file mode 100644 index 7f722316458a..000000000000 --- a/Documentation/devicetree/bindings/marvell.txt +++ /dev/null @@ -1,516 +0,0 @@ -Marvell Discovery mv64[345]6x System Controller chips -=========================================================== - -The Marvell mv64[345]60 series of system controller chips contain -many of the peripherals needed to implement a complete computer -system. In this section, we define device tree nodes to describe -the system controller chip itself and each of the peripherals -which it contains. Compatible string values for each node are -prefixed with the string "marvell,", for Marvell Technology Group Ltd. - -1) The /system-controller node - - This node is used to represent the system-controller and must be - present when the system uses a system controller chip. The top-level - system-controller node contains information that is global to all - devices within the system controller chip. The node name begins - with "system-controller" followed by the unit address, which is - the base address of the memory-mapped register set for the system - controller chip. - - Required properties: - - - ranges : Describes the translation of system controller addresses - for memory mapped registers. - - clock-frequency: Contains the main clock frequency for the system - controller chip. - - reg : This property defines the address and size of the - memory-mapped registers contained within the system controller - chip. The address specified in the "reg" property should match - the unit address of the system-controller node. - - #address-cells : Address representation for system controller - devices. This field represents the number of cells needed to - represent the address of the memory-mapped registers of devices - within the system controller chip. - - #size-cells : Size representation for the memory-mapped - registers within the system controller chip. - - #interrupt-cells : Defines the width of cells used to represent - interrupts. - - Optional properties: - - - model : The specific model of the system controller chip. Such - as, "mv64360", "mv64460", or "mv64560". - - compatible : A string identifying the compatibility identifiers - of the system controller chip. - - The system-controller node contains child nodes for each system - controller device that the platform uses. Nodes should not be created - for devices which exist on the system controller chip but are not used - - Example Marvell Discovery mv64360 system-controller node: - - system-controller@f1000000 { /* Marvell Discovery mv64360 */ - #address-cells = <1>; - #size-cells = <1>; - model = "mv64360"; /* Default */ - compatible = "marvell,mv64360"; - clock-frequency = <133333333>; - reg = <0xf1000000 0x10000>; - virtual-reg = <0xf1000000>; - ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */ - 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */ - 0xa0000000 0xa0000000 0x4000000 /* User FLASH */ - 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */ - 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */ - - [ child node definitions... ] - } - -2) Child nodes of /system-controller - - a) Marvell Discovery MDIO bus - - The MDIO is a bus to which the PHY devices are connected. For each - device that exists on this bus, a child node should be created. See - the definition of the PHY node below for an example of how to define - a PHY. - - Required properties: - - #address-cells : Should be <1> - - #size-cells : Should be <0> - - compatible : Should be "marvell,mv64360-mdio" - - Example: - - mdio { - #address-cells = <1>; - #size-cells = <0>; - compatible = "marvell,mv64360-mdio"; - - ethernet-phy@0 { - ...... - }; - }; - - - b) Marvell Discovery ethernet controller - - The Discover ethernet controller is described with two levels - of nodes. The first level describes an ethernet silicon block - and the second level describes up to 3 ethernet nodes within - that block. The reason for the multiple levels is that the - registers for the node are interleaved within a single set - of registers. The "ethernet-block" level describes the - shared register set, and the "ethernet" nodes describe ethernet - port-specific properties. - - Ethernet block node - - Required properties: - - #address-cells : <1> - - #size-cells : <0> - - compatible : "marvell,mv64360-eth-block" - - reg : Offset and length of the register set for this block - - Optional properties: - - clocks : Phandle to the clock control device and gate bit - - Example Discovery Ethernet block node: - ethernet-block@2000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "marvell,mv64360-eth-block"; - reg = <0x2000 0x2000>; - ethernet@0 { - ....... - }; - }; - - Ethernet port node - - Required properties: - - compatible : Should be "marvell,mv64360-eth". - - reg : Should be <0>, <1>, or <2>, according to which registers - within the silicon block the device uses. - - interrupts : <a> where a is the interrupt number for the port. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - phy : the phandle for the PHY connected to this ethernet - controller. - - local-mac-address : 6 bytes, MAC address - - Example Discovery Ethernet port node: - ethernet@0 { - compatible = "marvell,mv64360-eth"; - reg = <0>; - interrupts = <32>; - interrupt-parent = <&PIC>; - phy = <&PHY0>; - local-mac-address = [ 00 00 00 00 00 00 ]; - }; - - - - c) Marvell Discovery PHY nodes - - Required properties: - - interrupts : <a> where a is the interrupt number for this phy. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - reg : The ID number for the phy, usually a small integer - - Example Discovery PHY node: - ethernet-phy@1 { - compatible = "broadcom,bcm5421"; - interrupts = <76>; /* GPP 12 */ - interrupt-parent = <&PIC>; - reg = <1>; - }; - - - d) Marvell Discovery SDMA nodes - - Represent DMA hardware associated with the MPSC (multiprotocol - serial controllers). - - Required properties: - - compatible : "marvell,mv64360-sdma" - - reg : Offset and length of the register set for this device - - interrupts : <a> where a is the interrupt number for the DMA - device. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery SDMA node: - sdma@4000 { - compatible = "marvell,mv64360-sdma"; - reg = <0x4000 0xc18>; - virtual-reg = <0xf1004000>; - interrupts = <36>; - interrupt-parent = <&PIC>; - }; - - - e) Marvell Discovery BRG nodes - - Represent baud rate generator hardware associated with the MPSC - (multiprotocol serial controllers). - - Required properties: - - compatible : "marvell,mv64360-brg" - - reg : Offset and length of the register set for this device - - clock-src : A value from 0 to 15 which selects the clock - source for the baud rate generator. This value corresponds - to the CLKS value in the BRGx configuration register. See - the mv64x60 User's Manual. - - clock-frequence : The frequency (in Hz) of the baud rate - generator's input clock. - - current-speed : The current speed setting (presumably by - firmware) of the baud rate generator. - - Example Discovery BRG node: - brg@b200 { - compatible = "marvell,mv64360-brg"; - reg = <0xb200 0x8>; - clock-src = <8>; - clock-frequency = <133333333>; - current-speed = <9600>; - }; - - - f) Marvell Discovery CUNIT nodes - - Represent the Serial Communications Unit device hardware. - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery CUNIT node: - cunit@f200 { - reg = <0xf200 0x200>; - }; - - - g) Marvell Discovery MPSCROUTING nodes - - Represent the Discovery's MPSC routing hardware - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery CUNIT node: - mpscrouting@b500 { - reg = <0xb400 0xc>; - }; - - - h) Marvell Discovery MPSCINTR nodes - - Represent the Discovery's MPSC DMA interrupt hardware registers - (SDMA cause and mask registers). - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery MPSCINTR node: - mpsintr@b800 { - reg = <0xb800 0x100>; - }; - - - i) Marvell Discovery MPSC nodes - - Represent the Discovery's MPSC (Multiprotocol Serial Controller) - serial port. - - Required properties: - - compatible : "marvell,mv64360-mpsc" - - reg : Offset and length of the register set for this device - - sdma : the phandle for the SDMA node used by this port - - brg : the phandle for the BRG node used by this port - - cunit : the phandle for the CUNIT node used by this port - - mpscrouting : the phandle for the MPSCROUTING node used by this port - - mpscintr : the phandle for the MPSCINTR node used by this port - - cell-index : the hardware index of this cell in the MPSC core - - max_idle : value needed for MPSC CHR3 (Maximum Frame Length) - register - - interrupts : <a> where a is the interrupt number for the MPSC. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery MPSCINTR node: - mpsc@8000 { - compatible = "marvell,mv64360-mpsc"; - reg = <0x8000 0x38>; - virtual-reg = <0xf1008000>; - sdma = <&SDMA0>; - brg = <&BRG0>; - cunit = <&CUNIT>; - mpscrouting = <&MPSCROUTING>; - mpscintr = <&MPSCINTR>; - cell-index = <0>; - max_idle = <40>; - interrupts = <40>; - interrupt-parent = <&PIC>; - }; - - - j) Marvell Discovery Watch Dog Timer nodes - - Represent the Discovery's watchdog timer hardware - - Required properties: - - compatible : "marvell,mv64360-wdt" - - reg : Offset and length of the register set for this device - - Example Discovery Watch Dog Timer node: - wdt@b410 { - compatible = "marvell,mv64360-wdt"; - reg = <0xb410 0x8>; - }; - - - k) Marvell Discovery I2C nodes - - Represent the Discovery's I2C hardware - - Required properties: - - device_type : "i2c" - - compatible : "marvell,mv64360-i2c" - - reg : Offset and length of the register set for this device - - interrupts : <a> where a is the interrupt number for the I2C. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery I2C node: - compatible = "marvell,mv64360-i2c"; - reg = <0xc000 0x20>; - virtual-reg = <0xf100c000>; - interrupts = <37>; - interrupt-parent = <&PIC>; - }; - - - l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes - - Represent the Discovery's PIC hardware - - Required properties: - - #interrupt-cells : <1> - - #address-cells : <0> - - compatible : "marvell,mv64360-pic" - - reg : Offset and length of the register set for this device - - interrupt-controller - - Example Discovery PIC node: - pic { - #interrupt-cells = <1>; - #address-cells = <0>; - compatible = "marvell,mv64360-pic"; - reg = <0x0 0x88>; - interrupt-controller; - }; - - - m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes - - Represent the Discovery's MPP hardware - - Required properties: - - compatible : "marvell,mv64360-mpp" - - reg : Offset and length of the register set for this device - - Example Discovery MPP node: - mpp@f000 { - compatible = "marvell,mv64360-mpp"; - reg = <0xf000 0x10>; - }; - - - n) Marvell Discovery GPP (General Purpose Pins) nodes - - Represent the Discovery's GPP hardware - - Required properties: - - compatible : "marvell,mv64360-gpp" - - reg : Offset and length of the register set for this device - - Example Discovery GPP node: - gpp@f000 { - compatible = "marvell,mv64360-gpp"; - reg = <0xf100 0x20>; - }; - - - o) Marvell Discovery PCI host bridge node - - Represents the Discovery's PCI host bridge device. The properties - for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE - 1275-1994. A typical value for the compatible property is - "marvell,mv64360-pci". - - Example Discovery PCI host bridge node - pci@80000000 { - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - device_type = "pci"; - compatible = "marvell,mv64360-pci"; - reg = <0xcf8 0x8>; - ranges = <0x01000000 0x0 0x0 - 0x88000000 0x0 0x01000000 - 0x02000000 0x0 0x80000000 - 0x80000000 0x0 0x08000000>; - bus-range = <0 255>; - clock-frequency = <66000000>; - interrupt-parent = <&PIC>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = < - /* IDSEL 0x0a */ - 0x5000 0 0 1 &PIC 80 - 0x5000 0 0 2 &PIC 81 - 0x5000 0 0 3 &PIC 91 - 0x5000 0 0 4 &PIC 93 - - /* IDSEL 0x0b */ - 0x5800 0 0 1 &PIC 91 - 0x5800 0 0 2 &PIC 93 - 0x5800 0 0 3 &PIC 80 - 0x5800 0 0 4 &PIC 81 - - /* IDSEL 0x0c */ - 0x6000 0 0 1 &PIC 91 - 0x6000 0 0 2 &PIC 93 - 0x6000 0 0 3 &PIC 80 - 0x6000 0 0 4 &PIC 81 - - /* IDSEL 0x0d */ - 0x6800 0 0 1 &PIC 93 - 0x6800 0 0 2 &PIC 80 - 0x6800 0 0 3 &PIC 81 - 0x6800 0 0 4 &PIC 91 - >; - }; - - - p) Marvell Discovery CPU Error nodes - - Represent the Discovery's CPU error handler device. - - Required properties: - - compatible : "marvell,mv64360-cpu-error" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery CPU Error node: - cpu-error@70 { - compatible = "marvell,mv64360-cpu-error"; - reg = <0x70 0x10 0x128 0x28>; - interrupts = <3>; - interrupt-parent = <&PIC>; - }; - - - q) Marvell Discovery SRAM Controller nodes - - Represent the Discovery's SRAM controller device. - - Required properties: - - compatible : "marvell,mv64360-sram-ctrl" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery SRAM Controller node: - sram-ctrl@380 { - compatible = "marvell,mv64360-sram-ctrl"; - reg = <0x380 0x80>; - interrupts = <13>; - interrupt-parent = <&PIC>; - }; - - - r) Marvell Discovery PCI Error Handler nodes - - Represent the Discovery's PCI error handler device. - - Required properties: - - compatible : "marvell,mv64360-pci-error" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery PCI Error Handler node: - pci-error@1d40 { - compatible = "marvell,mv64360-pci-error"; - reg = <0x1d40 0x40 0xc28 0x4>; - interrupts = <12>; - interrupt-parent = <&PIC>; - }; - - - s) Marvell Discovery Memory Controller nodes - - Represent the Discovery's memory controller device. - - Required properties: - - compatible : "marvell,mv64360-mem-ctrl" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery Memory Controller node: - mem-ctrl@1400 { - compatible = "marvell,mv64360-mem-ctrl"; - reg = <0x1400 0x60>; - interrupts = <17>; - interrupt-parent = <&PIC>; - }; - - diff --git a/Documentation/devicetree/bindings/media/cdns,csi2rx.txt b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt new file mode 100644 index 000000000000..6b02a0657ad9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt @@ -0,0 +1,100 @@ +Cadence MIPI-CSI2 RX controller +=============================== + +The Cadence MIPI-CSI2 RX controller is a CSI-2 bridge supporting up to 4 CSI +lanes in input, and 4 different pixel streams in output. + +Required properties: + - compatible: must be set to "cdns,csi2rx" and an SoC-specific compatible + - reg: base address and size of the memory mapped region + - clocks: phandles to the clocks driving the controller + - clock-names: must contain: + * sys_clk: main clock + * p_clk: register bank clock + * pixel_if[0-3]_clk: pixel stream output clock, one for each stream + implemented in hardware, between 0 and 3 + +Optional properties: + - phys: phandle to the external D-PHY, phy-names must be provided + - phy-names: must contain "dphy", if the implementation uses an + external D-PHY + +Required subnodes: + - ports: A ports node with one port child node per device input and output + port, in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port nodes are numbered as follows: + + Port Description + ----------------------------- + 0 CSI-2 input + 1 Stream 0 output + 2 Stream 1 output + 3 Stream 2 output + 4 Stream 3 output + + The stream output port nodes are optional if they are not + connected to anything at the hardware level or implemented + in the design.Since there is only one endpoint per port, + the endpoints are not numbered. + + +Example: + +csi2rx: csi-bridge@0d060000 { + compatible = "cdns,csi2rx"; + reg = <0x0d060000 0x1000>; + clocks = <&byteclock>, <&byteclock> + <&coreclock>, <&coreclock>, + <&coreclock>, <&coreclock>; + clock-names = "sys_clk", "p_clk", + "pixel_if0_clk", "pixel_if1_clk", + "pixel_if2_clk", "pixel_if3_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi2rx_in_sensor: endpoint { + remote-endpoint = <&sensor_out_csi2rx>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + + csi2rx_out_grabber0: endpoint { + remote-endpoint = <&grabber0_in_csi2rx>; + }; + }; + + port@2 { + reg = <2>; + + csi2rx_out_grabber1: endpoint { + remote-endpoint = <&grabber1_in_csi2rx>; + }; + }; + + port@3 { + reg = <3>; + + csi2rx_out_grabber2: endpoint { + remote-endpoint = <&grabber2_in_csi2rx>; + }; + }; + + port@4 { + reg = <4>; + + csi2rx_out_grabber3: endpoint { + remote-endpoint = <&grabber3_in_csi2rx>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/cdns,csi2tx.txt b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt new file mode 100644 index 000000000000..459c6e332f52 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt @@ -0,0 +1,98 @@ +Cadence MIPI-CSI2 TX controller +=============================== + +The Cadence MIPI-CSI2 TX controller is a CSI-2 bridge supporting up to +4 CSI lanes in output, and up to 4 different pixel streams in input. + +Required properties: + - compatible: must be set to "cdns,csi2tx" + - reg: base address and size of the memory mapped region + - clocks: phandles to the clocks driving the controller + - clock-names: must contain: + * esc_clk: escape mode clock + * p_clk: register bank clock + * pixel_if[0-3]_clk: pixel stream output clock, one for each stream + implemented in hardware, between 0 and 3 + +Optional properties + - phys: phandle to the D-PHY. If it is set, phy-names need to be set + - phy-names: must contain "dphy" + +Required subnodes: + - ports: A ports node with one port child node per device input and output + port, in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port nodes are numbered as follows. + + Port Description + ----------------------------- + 0 CSI-2 output + 1 Stream 0 input + 2 Stream 1 input + 3 Stream 2 input + 4 Stream 3 input + + The stream input port nodes are optional if they are not + connected to anything at the hardware level or implemented + in the design. Since there is only one endpoint per port, + the endpoints are not numbered. + +Example: + +csi2tx: csi-bridge@0d0e1000 { + compatible = "cdns,csi2tx"; + reg = <0x0d0e1000 0x1000>; + clocks = <&byteclock>, <&byteclock>, + <&coreclock>, <&coreclock>, + <&coreclock>, <&coreclock>; + clock-names = "p_clk", "esc_clk", + "pixel_if0_clk", "pixel_if1_clk", + "pixel_if2_clk", "pixel_if3_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi2tx_out: endpoint { + remote-endpoint = <&remote_in>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + + csi2tx_in_stream0: endpoint { + remote-endpoint = <&stream0_out>; + }; + }; + + port@2 { + reg = <2>; + + csi2tx_in_stream1: endpoint { + remote-endpoint = <&stream1_out>; + }; + }; + + port@3 { + reg = <3>; + + csi2tx_in_stream2: endpoint { + remote-endpoint = <&stream2_out>; + }; + }; + + port@4 { + reg = <4>; + + csi2tx_in_stream3: endpoint { + remote-endpoint = <&stream3_out>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7251.txt b/Documentation/devicetree/bindings/media/i2c/ov7251.txt new file mode 100644 index 000000000000..8281151f7493 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov7251.txt @@ -0,0 +1,52 @@ +* Omnivision 1/7.5-Inch B&W VGA CMOS Digital Image Sensor + +The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor +with an active array size of 640H x 480V. It is programmable through a serial +I2C interface. + +Required Properties: +- compatible: Value should be "ovti,ov7251". +- clocks: Reference to the xclk clock. +- clock-names: Should be "xclk". +- clock-frequency: Frequency of the xclk clock. +- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds + to the hardware pin XSHUTDOWN which is physically active low. +- vdddo-supply: Chip digital IO regulator. +- vdda-supply: Chip analog regulator. +- vddd-supply: Chip digital core regulator. + +The device node shall contain one 'port' child node with a single 'endpoint' +subnode for its digital output video port, in accordance with the video +interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + &i2c1 { + ... + + ov7251: camera-sensor@60 { + compatible = "ovti,ov7251"; + reg = <0x60>; + + enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_bw_default>; + + clocks = <&clks 200>; + clock-names = "xclk"; + clock-frequency = <24000000>; + + vdddo-supply = <&camera_dovdd_1v8>; + vdda-supply = <&camera_avdd_2v8>; + vddd-supply = <&camera_dvdd_1v2>; + + port { + ov7251_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0>; + remote-endpoint = <&csi0_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov772x.txt b/Documentation/devicetree/bindings/media/i2c/ov772x.txt new file mode 100644 index 000000000000..0b3ede5b8e6a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov772x.txt @@ -0,0 +1,40 @@ +* Omnivision OV7720/OV7725 CMOS sensor + +The Omnivision OV7720/OV7725 sensor supports multiple resolutions output, +such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can +support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats. + +Required Properties: +- compatible: shall be one of + "ovti,ov7720" + "ovti,ov7725" +- clocks: reference to the xclk input clock. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the RSTB pin which is + active low, if any. +- powerdown-gpios: reference to the GPIO connected to the PWDN pin which is + active high, if any. + +The device node shall contain one 'port' child node with one child 'endpoint' +subnode for its digital output video port, in accordance with the video +interface bindings defined in Documentation/devicetree/bindings/media/ +video-interfaces.txt. + +Example: + +&i2c0 { + ov772x: camera@21 { + compatible = "ovti,ov7725"; + reg = <0x21>; + reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>; + clocks = <&xclk>; + + port { + ov772x_0: endpoint { + remote-endpoint = <&vcap1_in0>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt new file mode 100644 index 000000000000..4a3181a3dd7e --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt @@ -0,0 +1,19 @@ +* Panasonic AMG88xx + +The Panasonic family of AMG88xx Grid-Eye sensors allow recording +8x8 10Hz video which consists of thermal datapoints + +Required Properties: + - compatible : Must be "panasonic,amg88xx" + - reg : i2c address of the device + +Example: + + i2c0@1c22000 { + ... + amg88xx@69 { + compatible = "panasonic,amg88xx"; + reg = <0x69>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 1ce7ff9449c5..a19517e1c669 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -2,20 +2,28 @@ Renesas R-Car Video Input driver (rcar_vin) ------------------------------------------- The rcar_vin device provides video input capabilities for the Renesas R-Car -family of devices. The current blocks are always slaves and suppot one input -channel which can be either RGB, YUYV or BT656. +family of devices. + +Each VIN instance has a single parallel input that supports RGB and YUV video, +with both external synchronization and BT.656 synchronization for the latter. +Depending on the instance the VIN input is connected to external SoC pins, or +on Gen3 platforms to a CSI-2 receiver. - compatible: Must be one or more of the following - - "renesas,vin-r8a7795" for the R8A7795 device - - "renesas,vin-r8a7794" for the R8A7794 device - - "renesas,vin-r8a7793" for the R8A7793 device - - "renesas,vin-r8a7792" for the R8A7792 device - - "renesas,vin-r8a7791" for the R8A7791 device - - "renesas,vin-r8a7790" for the R8A7790 device - - "renesas,vin-r8a7779" for the R8A7779 device + - "renesas,vin-r8a7743" for the R8A7743 device + - "renesas,vin-r8a7745" for the R8A7745 device - "renesas,vin-r8a7778" for the R8A7778 device - - "renesas,rcar-gen2-vin" for a generic R-Car Gen2 compatible device. - - "renesas,rcar-gen3-vin" for a generic R-Car Gen3 compatible device. + - "renesas,vin-r8a7779" for the R8A7779 device + - "renesas,vin-r8a7790" for the R8A7790 device + - "renesas,vin-r8a7791" for the R8A7791 device + - "renesas,vin-r8a7792" for the R8A7792 device + - "renesas,vin-r8a7793" for the R8A7793 device + - "renesas,vin-r8a7794" for the R8A7794 device + - "renesas,vin-r8a7795" for the R8A7795 device + - "renesas,vin-r8a7796" for the R8A7796 device + - "renesas,vin-r8a77970" for the R8A77970 device + - "renesas,rcar-gen2-vin" for a generic R-Car Gen2 or RZ/G1 compatible + device. When compatible with the generic version nodes must list the SoC-specific version corresponding to the platform first @@ -28,21 +36,38 @@ channel which can be either RGB, YUYV or BT656. Additionally, an alias named vinX will need to be created to specify which video input device this is. -The per-board settings: +The per-board settings Gen2 platforms: - port sub-node describing a single endpoint connected to the vin as described in video-interfaces.txt[1]. Only the first one will be considered as each vin interface has one input port. - These settings are used to work out video input format and widths - into the system. +The per-board settings Gen3 platforms: +Gen3 platforms can support both a single connected parallel input source +from external SoC pins (port0) and/or multiple parallel input sources +from local SoC CSI-2 receivers (port1) depending on SoC. -Device node example -------------------- +- renesas,id - ID number of the VIN, VINx in the documentation. +- ports + - port 0 - sub-node describing a single endpoint connected to the VIN + from external SoC pins described in video-interfaces.txt[1]. + Describing more then one endpoint in port 0 is invalid. Only VIN + instances that are connected to external pins should have port 0. + - port 1 - sub-nodes describing one or more endpoints connected to + the VIN from local SoC CSI-2 receivers. The endpoint numbers must + use the following schema. - aliases { - vin0 = &vin0; - }; + - Endpoint 0 - sub-node describing the endpoint connected to CSI20 + - Endpoint 1 - sub-node describing the endpoint connected to CSI21 + - Endpoint 2 - sub-node describing the endpoint connected to CSI40 + - Endpoint 3 - sub-node describing the endpoint connected to CSI41 + +Device node example for Gen2 platforms +-------------------------------------- + + aliases { + vin0 = &vin0; + }; vin0: vin@e6ef0000 { compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin"; @@ -52,8 +77,8 @@ Device node example status = "disabled"; }; -Board setup example (vin1 composite video input) ------------------------------------------------- +Board setup example for Gen2 platforms (vin1 composite video input) +------------------------------------------------------------------- &i2c2 { status = "okay"; @@ -92,6 +117,77 @@ Board setup example (vin1 composite video input) }; }; +Device node example for Gen3 platforms +-------------------------------------- + + vin0: video@e6ef0000 { + compatible = "renesas,vin-r8a7795"; + reg = <0 0xe6ef0000 0 0x1000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 811>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 811>; + renesas,id = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin0csi20: endpoint@0 { + reg = <0>; + remote-endpoint= <&csi20vin0>; + }; + vin0csi21: endpoint@1 { + reg = <1>; + remote-endpoint= <&csi21vin0>; + }; + vin0csi40: endpoint@2 { + reg = <2>; + remote-endpoint= <&csi40vin0>; + }; + }; + }; + }; + csi20: csi2@fea80000 { + compatible = "renesas,r8a7795-csi2"; + reg = <0 0xfea80000 0 0x10000>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 714>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 714>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + csi20_in: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&adv7482_txb>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + csi20vin0: endpoint@0 { + reg = <0>; + remote-endpoint = <&vin0csi20>; + }; + }; + }; + }; [1] video-interfaces.txt common video media interface diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt index 3fc66dfb192c..8a7a616e9019 100644 --- a/Documentation/devicetree/bindings/media/renesas,ceu.txt +++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt @@ -2,14 +2,15 @@ Renesas Capture Engine Unit (CEU) ---------------------------------------------- The Capture Engine Unit is the image capture interface found in the Renesas -SH Mobile and RZ SoCs. +SH Mobile, R-Mobile and RZ SoCs. The interface supports a single parallel input with data bus width of 8 or 16 bits. Required properties: -- compatible: Shall be "renesas,r7s72100-ceu" for CEU units found in RZ/A1H - and RZ/A1M SoCs. +- compatible: Shall be one of the following values: + "renesas,r7s72100-ceu" for CEU units found in RZ/A1H and RZ/A1M SoCs + "renesas,r8a7740-ceu" for CEU units found in R-Mobile A1 R8A7740 SoCs - reg: Registers address base and size. - interrupts: The interrupt specifier. diff --git a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt new file mode 100644 index 000000000000..2d385b65b275 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt @@ -0,0 +1,101 @@ +Renesas R-Car MIPI CSI-2 +------------------------ + +The R-Car CSI-2 receiver device provides MIPI CSI-2 capabilities for the +Renesas R-Car family of devices. It is used in conjunction with the +R-Car VIN module, which provides the video capture capabilities. + +Mandatory properties +-------------------- + - compatible: Must be one or more of the following + - "renesas,r8a7795-csi2" for the R8A7795 device. + - "renesas,r8a7796-csi2" for the R8A7796 device. + - "renesas,r8a77965-csi2" for the R8A77965 device. + - "renesas,r8a77970-csi2" for the R8A77970 device. + + - reg: the register base and size for the device registers + - interrupts: the interrupt for the device + - clocks: reference to the parent clock + +The device node shall contain two 'port' child nodes according to the +bindings defined in Documentation/devicetree/bindings/media/ +video-interfaces.txt. port@0 shall connect to the CSI-2 source. port@1 +shall connect to all the R-Car VIN modules that have a hardware +connection to the CSI-2 receiver. + +- port@0- Video source (mandatory) + - endpoint@0 - sub-node describing the endpoint that is the video source + +- port@1 - VIN instances (optional) + - One endpoint sub-node for every R-Car VIN instance which is connected + to the R-Car CSI-2 receiver. + +Example: + + csi20: csi2@fea80000 { + compatible = "renesas,r8a7796-csi2"; + reg = <0 0xfea80000 0 0x10000>; + interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 714>; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 714>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + + csi20_in: endpoint@0 { + reg = <0>; + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&adv7482_txb>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + csi20vin0: endpoint@0 { + reg = <0>; + remote-endpoint = <&vin0csi20>; + }; + csi20vin1: endpoint@1 { + reg = <1>; + remote-endpoint = <&vin1csi20>; + }; + csi20vin2: endpoint@2 { + reg = <2>; + remote-endpoint = <&vin2csi20>; + }; + csi20vin3: endpoint@3 { + reg = <3>; + remote-endpoint = <&vin3csi20>; + }; + csi20vin4: endpoint@4 { + reg = <4>; + remote-endpoint = <&vin4csi20>; + }; + csi20vin5: endpoint@5 { + reg = <5>; + remote-endpoint = <&vin5csi20>; + }; + csi20vin6: endpoint@6 { + reg = <6>; + remote-endpoint = <&vin6csi20>; + }; + csi20vin7: endpoint@7 { + reg = <7>; + remote-endpoint = <&vin7csi20>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt index c7888d6f6408..880d4d70c9fd 100644 --- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt @@ -28,7 +28,7 @@ See: Documentation/devicetree/bindings/clock/clock-bindings.txt - pinctrl-names : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num) must be defined for each tsin child node. - pinctrl-0 : phandle referencing pin configuration for this tsin configuration -See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt +See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt Required properties (tsin (child) node): diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.txt index f9632bacbd04..7d60a50a4fa1 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.txt @@ -6,11 +6,21 @@ Required properties: example below. Note that the MC registers are interleaved with the GART registers, and hence must be represented as multiple ranges. - interrupts : Should contain MC General interrupt. +- #reset-cells : Should be 1. This cell represents memory client module ID. + The assignments may be found in header file <dt-bindings/memory/tegra20-mc.h> + or in the TRM documentation. Example: - memory-controller@7000f000 { + mc: memory-controller@7000f000 { compatible = "nvidia,tegra20-mc"; reg = <0x7000f000 0x024 0x7000f03c 0x3c4>; interrupts = <0 77 0x04>; + #reset-cells = <1>; + }; + + video-codec@6001a000 { + compatible = "nvidia,tegra20-vde"; + ... + resets = <&mc TEGRA20_MC_RESET_VDE>; }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt index 14968b048cd3..a878b5908a4d 100644 --- a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt @@ -12,6 +12,9 @@ Required properties: - clock-names: Must include the following entries: - mc: the module's clock input - interrupts: The interrupt outputs from the controller. +- #reset-cells : Should be 1. This cell represents memory client module ID. + The assignments may be found in header file <dt-bindings/memory/tegra30-mc.h> + or in the TRM documentation. Required properties for Tegra30, Tegra114, Tegra124, Tegra132 and Tegra210: - #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines @@ -72,12 +75,14 @@ Example SoC include file: interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; + #reset-cells = <1>; }; sdhci@700b0000 { compatible = "nvidia,tegra124-sdhci"; ... iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; + resets = <&mc TEGRA124_MC_RESET_SDMMC1>; }; }; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index bdd017686ea5..a014afb07902 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -50,7 +50,7 @@ Required properties: Optional properties: - - wlf,reset : GPIO specifier for the GPIO controlling /RESET + - reset-gpios : GPIO specifier for the GPIO controlling /RESET - clocks: Should reference the clocks supplied on MCLK1 and MCLK2 - clock-names: Should contains two strings: @@ -70,6 +70,10 @@ Optional properties: Documentation/devicetree/bindings/regulator/regulator.txt (wm5102, wm5110, wm8280, wm8997, wm8998, wm1814) +Deprecated properties: + + - wlf,reset : GPIO specifier for the GPIO controlling /RESET + Also see child specific device properties: Regulator - ../regulator/arizona-regulator.txt Extcon - ../extcon/extcon-arizona.txt diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt index 0b2a6099aa20..5297b2210704 100644 --- a/Documentation/devicetree/bindings/mfd/as3722.txt +++ b/Documentation/devicetree/bindings/mfd/as3722.txt @@ -46,7 +46,7 @@ is required: Following properties are require if pin control setting is required at boot. - pinctrl-names: A pinctrl state named "default" be defined, using the - bindings in pinctrl/pinctrl-binding.txt. + bindings in pinctrl/pinctrl-bindings.txt. - pinctrl[0...n]: Properties to contain the phandle that refer to different nodes of pin control settings. These nodes represents the pin control setting of state 0 to state n. Each of these diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index 9455503b0299..d1762f3b30af 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -43,7 +43,7 @@ Optional properties: regulator to drive the OTG VBus, rather then as an input pin which signals whether the board is driving OTG VBus or not. - (axp221 / axp223 / axp813 only) + (axp221 / axp223 / axp803/ axp813 only) - x-powers,master-mode: Boolean (axp806 only). Set this when the PMIC is wired for master mode. The default is slave mode. @@ -132,6 +132,7 @@ FLDO2 : LDO : fldoin-supply : shared supply LDO_IO0 : LDO : ips-supply : GPIO 0 LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator AXP806 regulators, type, and corresponding input supply names: diff --git a/Documentation/devicetree/bindings/mfd/bd9571mwv.txt b/Documentation/devicetree/bindings/mfd/bd9571mwv.txt index 9ab216a851d5..25d1f697eb25 100644 --- a/Documentation/devicetree/bindings/mfd/bd9571mwv.txt +++ b/Documentation/devicetree/bindings/mfd/bd9571mwv.txt @@ -25,6 +25,25 @@ Required properties: Each child node is defined using the standard binding for regulators. +Optional properties: + - rohm,ddr-backup-power : Value to use for DDR-Backup Power (default 0). + This is a bitmask that specifies which DDR power + rails need to be kept powered when backup mode is + entered, for system suspend: + - bit 0: DDR0 + - bit 1: DDR1 + - bit 2: DDR0C + - bit 3: DDR1C + These bits match the KEEPON_DDR* bits in the + documentation for the "BKUP Mode Cnt" register. + - rohm,rstbmode-level: The RSTB signal is configured for level mode, to + accommodate a toggle power switch (the RSTBMODE pin is + strapped low). + - rohm,rstbmode-pulse: The RSTB signal is configured for pulse mode, to + accommodate a momentary power switch (the RSTBMODE pin + is strapped high). + The two properties above are mutually exclusive. + Example: pmic: pmic@30 { @@ -36,6 +55,8 @@ Example: #interrupt-cells = <2>; gpio-controller; #gpio-cells = <2>; + rohm,ddr-backup-power = <0xf>; + rohm,rstbmode-pulse; regulators { dvfs: dvfs { diff --git a/Documentation/devicetree/bindings/mfd/da9063.txt b/Documentation/devicetree/bindings/mfd/da9063.txt index 05b21bcb8543..443e68286957 100644 --- a/Documentation/devicetree/bindings/mfd/da9063.txt +++ b/Documentation/devicetree/bindings/mfd/da9063.txt @@ -1,4 +1,4 @@ -* Dialog DA9063 Power Management Integrated Circuit (PMIC) +* Dialog DA9063/DA9063L Power Management Integrated Circuit (PMIC) DA9093 consists of a large and varied group of sub-devices (I2C Only): @@ -6,14 +6,14 @@ Device Supply Names Description ------ ------------ ----------- da9063-regulator : : LDOs & BUCKs da9063-onkey : : On Key -da9063-rtc : : Real-Time Clock +da9063-rtc : : Real-Time Clock (DA9063 only) da9063-watchdog : : Watchdog ====== Required properties: -- compatible : Should be "dlg,da9063" +- compatible : Should be "dlg,da9063" or "dlg,da9063l" - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be modified to match the chip's OTP settings). - interrupt-parent : Specifies the reference to the interrupt controller for @@ -23,8 +23,8 @@ Required properties: Sub-nodes: -- regulators : This node defines the settings for the LDOs and BUCKs. The - DA9063 regulators are bound using their names listed below: +- regulators : This node defines the settings for the LDOs and BUCKs. + The DA9063(L) regulators are bound using their names listed below: bcore1 : BUCK CORE1 bcore2 : BUCK CORE2 @@ -32,16 +32,16 @@ Sub-nodes: bmem : BUCK MEM bio : BUCK IO bperi : BUCK PERI - ldo1 : LDO_1 - ldo2 : LDO_2 + ldo1 : LDO_1 (DA9063 only) + ldo2 : LDO_2 (DA9063 only) ldo3 : LDO_3 - ldo4 : LDO_4 - ldo5 : LDO_5 - ldo6 : LDO_6 + ldo4 : LDO_4 (DA9063 only) + ldo5 : LDO_5 (DA9063 only) + ldo6 : LDO_6 (DA9063 only) ldo7 : LDO_7 ldo8 : LDO_8 ldo9 : LDO_9 - ldo10 : LDO_10 + ldo10 : LDO_10 (DA9063 only) ldo11 : LDO_11 The component follows the standard regulator framework and the bindings @@ -49,8 +49,9 @@ Sub-nodes: Documentation/devicetree/bindings/regulator/regulator.txt - rtc : This node defines settings for the Real-Time Clock associated with - the DA9063. There are currently no entries in this binding, however - compatible = "dlg,da9063-rtc" should be added if a node is created. + the DA9063 only. The RTC is not present in DA9063L. There are currently + no entries in this binding, however compatible = "dlg,da9063-rtc" should + be added if a node is created. - onkey : This node defines the OnKey settings for controlling the key functionality of the device. The node should contain the compatible property @@ -65,8 +66,9 @@ Sub-nodes: and KEY_SLEEP. - watchdog : This node defines settings for the Watchdog timer associated - with the DA9063. There are currently no entries in this binding, however - compatible = "dlg,da9063-watchdog" should be added if a node is created. + with the DA9063 and DA9063L. There are currently no entries in this + binding, however compatible = "dlg,da9063-watchdog" should be added + if a node is created. Example: diff --git a/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt b/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt index 15bc885f9df4..c639705a98ef 100644 --- a/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt +++ b/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt @@ -12,6 +12,30 @@ Required properties: - spi-max-frequency : Typically set to 3000000 - spi-cs-high : SPI chip select direction +Optional subnodes: + +The sub-functions of CPCAP get their own node with their own compatible values, +which are described in the following files: + +- ../power/supply/cpcap-battery.txt +- ../power/supply/cpcap-charger.txt +- ../regulator/cpcap-regulator.txt +- ../phy/phy-cpcap-usb.txt +- ../input/cpcap-pwrbutton.txt +- ../rtc/cpcap-rtc.txt +- ../leds/leds-cpcap.txt +- ../iio/adc/cpcap-adc.txt + +The only exception is the audio codec. Instead of a compatible value its +node must be named "audio-codec". + +Required properties for the audio-codec subnode: + +- #sound-dai-cells = <1>; + +The audio-codec provides two DAIs. The first one is connected to the +Stereo HiFi DAC and the second one is connected to the Voice DAC. + Example: &mcspi1 { @@ -26,6 +50,24 @@ Example: #size-cells = <0>; spi-max-frequency = <3000000>; spi-cs-high; + + audio-codec { + #sound-dai-cells = <1>; + + /* HiFi */ + port@0 { + endpoint { + remote-endpoint = <&cpu_dai1>; + }; + }; + + /* Voice */ + port@1 { + endpoint { + remote-endpoint = <&cpu_dai2>; + }; + }; + }; }; }; diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt index 522a3bbf1bac..0ebd08af777d 100644 --- a/Documentation/devicetree/bindings/mfd/mt6397.txt +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -7,11 +7,12 @@ MT6397/MT6323 is a multifunction device with the following sub modules: - GPIO - Clock - LED +- Keys It is interfaced to host controller using SPI interface by a proprietary hardware called PMIC wrapper or pwrap. MT6397/MT6323 MFD is a child device of pwrap. See the following for pwarp node definitions: -Documentation/devicetree/bindings/soc/pwrap.txt +Documentation/devicetree/bindings/soc/mediatek/pwrap.txt This document describes the binding for MFD device and its sub module. @@ -40,6 +41,11 @@ Optional subnodes: - compatible: "mediatek,mt6323-led" see Documentation/devicetree/bindings/leds/leds-mt6323.txt +- keys + Required properties: + - compatible: "mediatek,mt6397-keys" or "mediatek,mt6323-keys" + see Documentation/devicetree/bindings/input/mtk-pmic-keys.txt + Example: pwrap: pwrap@1000f000 { compatible = "mediatek,mt8135-pwrap"; diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt index 6ac06c1b9aec..143706222a51 100644 --- a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt @@ -29,6 +29,9 @@ Required properties: "qcom,pm8916", "qcom,pm8004", "qcom,pm8909", + "qcom,pm8998", + "qcom,pmi8998", + "qcom,pm8005", or generalized "qcom,spmi-pmic". - reg: Specifies the SPMI USID slave address for this device. For more information see: diff --git a/Documentation/devicetree/bindings/mfd/stm32-timers.txt b/Documentation/devicetree/bindings/mfd/stm32-timers.txt index 1db6e0057a63..0e900b52e895 100644 --- a/Documentation/devicetree/bindings/mfd/stm32-timers.txt +++ b/Documentation/devicetree/bindings/mfd/stm32-timers.txt @@ -19,6 +19,11 @@ Required parameters: Optional parameters: - resets: Phandle to the parent reset controller. See ../reset/st,stm32-rcc.txt +- dmas: List of phandle to dma channels that can be used for + this timer instance. There may be up to 7 dma channels. +- dma-names: List of dma names. Must match 'dmas' property. Valid + names are: "ch1", "ch2", "ch3", "ch4", "up", "trig", + "com". Optional subnodes: - pwm: See ../pwm/pwm-stm32.txt @@ -44,3 +49,18 @@ Example: reg = <0>; }; }; + +Example with all dmas: + timer@40010000 { + ... + dmas = <&dmamux1 11 0x400 0x0>, + <&dmamux1 12 0x400 0x0>, + <&dmamux1 13 0x400 0x0>, + <&dmamux1 14 0x400 0x0>, + <&dmamux1 15 0x400 0x0>, + <&dmamux1 16 0x400 0x0>, + <&dmamux1 17 0x400 0x0>; + dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig", "com"; + ... + child nodes... + }; diff --git a/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt b/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt index dd2c06540485..daa091c2e67b 100644 --- a/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt +++ b/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt @@ -8,8 +8,8 @@ Required properties: - reg: The PRCM registers range The prcm node may contain several subdevices definitions: - - see Documentation/devicetree/clk/sunxi.txt for clock devices - - see Documentation/devicetree/reset/allwinner,sunxi-clock-reset.txt for reset + - see Documentation/devicetree/bindings/clock/sunxi.txt for clock devices + - see Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt for reset controller devices diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt index a086f1e1cdd7..7f0822b4beae 100644 --- a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt @@ -61,7 +61,6 @@ Example of the RCU bindings on a xRX200 SoC: usb_phy0: usb2-phy@18 { compatible = "lantiq,xrx200-usb2-phy"; reg = <0x18 4>, <0x38 4>; - status = "disabled"; resets = <&reset1 4 4>, <&reset0 4 4>; reset-names = "phy", "ctrl"; @@ -71,7 +70,6 @@ Example of the RCU bindings on a xRX200 SoC: usb_phy1: usb2-phy@34 { compatible = "lantiq,xrx200-usb2-phy"; reg = <0x34 4>, <0x3C 4>; - status = "disabled"; resets = <&reset1 5 4>, <&reset0 4 4>; reset-names = "phy", "ctrl"; diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt index 50bf611a4d2c..13e70409e8ac 100644 --- a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -12,6 +12,7 @@ Required properties: - "amlogic,meson-gxbb-mmc" - "amlogic,meson-gxl-mmc" - "amlogic,meson-gxm-mmc" + - "amlogic,meson-axg-mmc" - clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. - clock-names: Should contain the following: "core" - Main peripheral bus clock @@ -19,6 +20,7 @@ Required properties: "clkin1" - Other parent clock of internal mux The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the clock rate requested by the MMC core. +- resets : phandle of the internal reset line Example: @@ -29,4 +31,5 @@ Example: clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; clock-names = "core", "clkin0", "clkin1"; pinctrl-0 = <&emmc_pins>; + resets = <&reset RESET_SD_EMMC_A>; }; diff --git a/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt new file mode 100644 index 000000000000..b0f0999ea1a9 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt @@ -0,0 +1,29 @@ +* Mellanox Bluefield SoC specific extensions to the Synopsys Designware + Mobile Storage Host Controller + +Read synopsys-dw-mshc.txt for more details + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Mellanox Bluefield SoC +specific extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be one of the following. + - "mellanox,bluefield-dw-mshc": for controllers with Mellanox Bluefield SoC + specific extensions. + +Example: + + /* Mellanox Bluefield SoC MMC */ + mmc@6008000 { + compatible = "mellanox,bluefield-dw-mshc"; + reg = <0x6008000 0x400>; + interrupts = <32>; + fifo-depth = <0x100>; + clock-frequency = <24000000>; + bus-width = <8>; + cap-mmc-highspeed; + }; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index a58c173b7ab9..0419a63f73a0 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -62,7 +62,7 @@ Required properties for a slot (Deprecated - Recommend to use one slot per host) rest of the gpios (depending on the bus-width property) are the data lines in no particular order. The format of the gpio specifier depends on the gpio controller. -(Deprecated - Refer to Documentation/devicetree/binding/pinctrl/samsung-pinctrl.txt) +(Deprecated - Refer to Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt) Example: diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt new file mode 100644 index 000000000000..7cd8c432d7c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/jz4740.txt @@ -0,0 +1,38 @@ +* Ingenic JZ47xx MMC controllers + +This file documents the device tree properties used for the MMC controller in +Ingenic JZ4740/JZ4780 SoCs. These are in addition to the core MMC properties +described in mmc.txt. + +Required properties: +- compatible: Should be one of the following: + - "ingenic,jz4740-mmc" for the JZ4740 + - "ingenic,jz4780-mmc" for the JZ4780 +- reg: Should contain the MMC controller registers location and length. +- interrupts: Should contain the interrupt specifier of the MMC controller. +- clocks: Clock for the MMC controller. + +Optional properties: +- dmas: List of DMA specifiers with the controller specific format + as described in the generic DMA client binding. A tx and rx + specifier is required. +- dma-names: RX and TX DMA request names. + Should be "rx" and "tx", in that order. + +For additional details on DMA client bindings see ../dma/dma.txt. + +Example: + +mmc0: mmc@13450000 { + compatible = "ingenic,jz4780-mmc"; + reg = <0x13450000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <37>; + + clocks = <&cgu JZ4780_CLK_MSC0>; + clock-names = "mmc"; + + dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>, <&dma JZ4780_DMA_MSC0_TX 0xffffffff>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt index 3149297b3933..f064528effed 100644 --- a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt +++ b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt @@ -12,7 +12,7 @@ Required properties: See: Documentation/devicetree/bindings/clock/clock-bindings.txt - pinctrl-names: A pinctrl state names "default" must be defined. - pinctrl-0: Phandle referencing pin configuration of the SDHCI controller. - See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt Example: diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 467cd7b147ce..f5a0923b34ca 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -19,6 +19,8 @@ Optional properties: - wp-gpios: Specify GPIOs for write protection, see gpio binding - cd-inverted: when present, polarity on the CD line is inverted. See the note below for the case, when a GPIO is used for the CD line +- cd-debounce-delay-ms: Set delay time before detecting card after card insert interrupt. + It's only valid when cd-gpios is present. - wp-inverted: when present, polarity on the WP line is inverted. See the note below for the case, when a GPIO is used for the WP line - disable-wp: When set no physical WP line is present. This property should @@ -56,6 +58,10 @@ Optional properties: - fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type. The value <n> is the driver type as specified in the eMMC specification (table 206 in spec version 5.1). +- post-power-on-delay-ms : It was invented for MMC pwrseq-simple which could + be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay + waiting for I/O signalling and card power supply to be stable, regardless of + whether pwrseq-simple is used. Default to 10ms if no available. *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt index 51775a372c06..393848c2138e 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt @@ -4,7 +4,14 @@ Refer to mmc.txt for standard MMC bindings. Required properties: - compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers + Should be "ti,k2g-sdhci" for K2G - ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1 + (Not required for K2G). +- pinctrl-names: Should be subset of "default", "hs", "sdr12", "sdr25", "sdr50", + "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104", + "ddr_1_8v-rev11", "ddr_1_8v" or "ddr_3_3v", "hs200_1_8v-rev11", + "hs200_1_8v", +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt Example: mmc1: mmc@4809c000 { diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 6b3d40ca395e..ccf82b4ee838 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -20,7 +20,7 @@ Required properties: - pinctrl-names: A pinctrl state names "default" must be defined. - pinctrl-0: Phandle referencing pin configuration of the sd/emmc controller. - See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - reg: This must provide the host controller base address and it can also contain the FlashSS Top register for TX/RX delay used by the driver diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 2d5287eeed95..839f469f4525 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -26,6 +26,8 @@ Required properties: "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC + "renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC + "renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC "renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller @@ -67,7 +69,6 @@ Example: R8A7790 (R-Car H2) SDHI controller nodes max-frequency = <195000000>; power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; resets = <&cpg 314>; - status = "disabled"; }; sdhi1: sd@ee120000 { @@ -81,7 +82,6 @@ Example: R8A7790 (R-Car H2) SDHI controller nodes max-frequency = <195000000>; power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; resets = <&cpg 313>; - status = "disabled"; }; sdhi2: sd@ee140000 { @@ -95,7 +95,6 @@ Example: R8A7790 (R-Car H2) SDHI controller nodes max-frequency = <97500000>; power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; resets = <&cpg 312>; - status = "disabled"; }; sdhi3: sd@ee160000 { @@ -109,5 +108,4 @@ Example: R8A7790 (R-Car H2) SDHI controller nodes max-frequency = <97500000>; power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; resets = <&cpg 311>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index b289ef3c1b7e..393588385c6e 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -47,6 +47,11 @@ Optional properties: partitions written from Linux with this feature turned on may not be accessible by the BootROM code. + - nand-ecc-strength: integer representing the number of bits to correct + per ECC step. Needs to be a multiple of 2. + - nand-ecc-step-size: integer representing the number of data bytes + that are covered by a single ECC step. The driver + supports 512 and 1024. The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt b/Documentation/devicetree/bindings/mtd/ibm,ndfc.txt index 869f0b5f16e8..869f0b5f16e8 100644 --- a/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt +++ b/Documentation/devicetree/bindings/mtd/ibm,ndfc.txt diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt index 1c88526dedfc..4d3ec5e4ff8a 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -20,7 +20,6 @@ Required NFI properties: - interrupts: Interrupts of NFI. - clocks: NFI required clocks. - clock-names: NFI clocks internal name. -- status: Disabled default. Then set "okay" by platform. - ecc-engine: Required ECC Engine node. - #address-cells: NAND chip index, should be 1. - #size-cells: Should be 0. @@ -34,7 +33,6 @@ Example: clocks = <&pericfg CLK_PERI_NFI>, <&pericfg CLK_PERI_NFI_PAD>; clock-names = "nfi_clk", "pad_clk"; - status = "disabled"; ecc-engine = <&bch>; #address-cells = <1>; #size-cells = <0>; @@ -50,14 +48,19 @@ Optional: - nand-on-flash-bbt: Store BBT on NAND Flash. - nand-ecc-mode: the NAND ecc mode (check driver for supported modes) - nand-ecc-step-size: Number of data bytes covered by a single ECC step. - valid values: 512 and 1024. + valid values: + 512 and 1024 on mt2701 and mt2712. + 512 only on mt7622. 1024 is recommended for large page NANDs. - nand-ecc-strength: Number of bits to correct per ECC step. - The valid values that the controller supports are: 4, 6, - 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44, - 48, 52, 56, 60. + The valid values that each controller supports: + mt2701: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, + 32, 36, 40, 44, 48, 52, 56, 60. + mt2712: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, + 32, 36, 40, 44, 48, 52, 56, 60, 68, 72, 80. + mt7622: 4, 6, 8, 10, 12, 14, 16. The strength should be calculated as follows: - E = (S - F) * 8 / 14 + E = (S - F) * 8 / B S = O / (P / Q) E : nand-ecc-strength. S : spare size per sector. @@ -66,6 +69,15 @@ Optional: O : oob size. P : page size. Q : nand-ecc-step-size. + B : number of parity bits needed to correct + 1 bitflip. + According to MTK NAND controller design, + this number depends on max ecc step size + that MTK NAND controller supports. + If max ecc step size supported is 1024, + then it should be always 14. And if max + ecc step size is 512, then it should be + always 13. If the result does not match any one of the listed choices above, please select the smaller valid value from the list. @@ -152,7 +164,6 @@ Required BCH properties: - interrupts: Interrupts of ECC. - clocks: ECC required clocks. - clock-names: ECC clocks internal name. -- status: Disabled default. Then set "okay" by platform. Example: @@ -162,5 +173,4 @@ Example: interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>; clocks = <&pericfg CLK_PERI_NFI_ECC>; clock-names = "nfiecc_clk"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index 36f3b769a626..a8f382642ba9 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -14,7 +14,7 @@ method is used for a given flash device. To describe the method there should be a subnode of the flash device that is named 'partitions'. It must have a 'compatible' property, which is used to identify the method to use. -We currently only document a binding for fixed layouts. +Available bindings are listed in the "partitions" subdirectory. Fixed Partitions diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.txt b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.txt new file mode 100644 index 000000000000..1d61a029395e --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.txt @@ -0,0 +1,42 @@ +Broadcom BCM47xx Partitions +=========================== + +Broadcom is one of hardware manufacturers providing SoCs (BCM47xx) used in +home routers. Their BCM947xx boards using CFE bootloader have several partitions +without any on-flash partition table. On some devices their sizes and/or +meanings can also vary so fixed partitioning can't be used. + +Discovering partitions on these devices is possible thanks to having a special +header and/or magic signature at the beginning of each of them. They are also +block aligned which is important for determinig a size. + +Most of partitions use ASCII text based magic for determining a type. More +complex partitions (like TRX with its HDR0 magic) may include extra header +containing some details, including a length. + +A list of supported partitions includes: +1) Bootloader with Broadcom's CFE (Common Firmware Environment) +2) NVRAM with configuration/calibration data +3) Device manufacturer's data with some default values (e.g. SSIDs) +4) TRX firmware container which can hold up to 4 subpartitions +5) Backup TRX firmware used after failed upgrade + +As mentioned earlier, role of some partitions may depend on extra configuration. +For example both: main firmware and backup firmware use the same TRX format with +the same header. To distinguish currently used firmware a CFE's environment +variable "bootpartition" is used. + + +Devices using Broadcom partitions described above should should have flash node +with a subnode named "partitions" using following properties: + +Required properties: +- compatible : (required) must be "brcm,bcm947xx-cfe-partitions" + +Example: + +flash@0 { + partitions { + compatible = "brcm,bcm947xx-cfe-partitions"; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index 0734f03bf3d3..dcd5a5d80dc0 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -22,8 +22,6 @@ Optional properties: - reset : phandle + reset specifier pair - reset-names : must contain "ahb" - allwinner,rb : shall contain the native Ready/Busy ids. - or -- rb-gpios : shall contain the gpios used as R/B pins. - nand-ecc-mode : one of the supported ECC modes ("hw", "soft", "soft_bch" or "none") diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 8acf51a4dfa8..47a6a7fe0b86 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -10,6 +10,7 @@ Required properties: "brcm,bcm53128" "brcm,bcm5365" "brcm,bcm5395" + "brcm,bcm5389" "brcm,bcm5397" "brcm,bcm5398" diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index cfe8f64eca4f..3ceeb8de1196 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -82,8 +82,6 @@ linked into one DSA cluster. switch0: switch0@0 { compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 0>; @@ -135,8 +133,6 @@ linked into one DSA cluster. switch1: switch1@0 { compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 1>; @@ -204,8 +200,6 @@ linked into one DSA cluster. switch2: switch2@0 { compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; reg = <0>; dsa,member = <0 2>; diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index fd23904ac68e..a700943218ca 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -6,7 +6,7 @@ Required properties: - compatible: For external switch chips, compatible string must be exactly one of: "microchip,ksz9477" -See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. Examples: diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt index a9bc27b93ee3..aa3527f71fdc 100644 --- a/Documentation/devicetree/bindings/net/dsa/mt7530.txt +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -31,7 +31,7 @@ Required properties for the child nodes within ports container: - phy-mode: String, must be either "trgmii" or "rgmii" for port labeled "cpu". -See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required, optional properties and how the integrated switch subnodes must be specified. diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt index 9c67ee4890d7..bbcb255c3150 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -2,7 +2,10 @@ Required properties: -- compatible: should be "qca,qca8337" +- compatible: should be one of: + "qca,qca8334" + "qca,qca8337" + - #size-cells: must be 0 - #address-cells: must be 1 @@ -14,6 +17,20 @@ port and PHY id, each subnode describing a port needs to have a valid phandle referencing the internal PHY connected to it. The CPU port of this switch is always port 0. +A CPU port node has the following optional node: + +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + +For QCA8K the 'fixed-link' sub-node supports only the following properties: + +- 'speed' (integer, mandatory), to indicate the link speed. Accepted + values are 10, 100 and 1000 +- 'full-duplex' (boolean, optional), to indicate that full duplex is + used. When absent, half duplex is assumed. + Example: @@ -53,6 +70,10 @@ Example: label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; + fixed-link { + speed = 1000; + full-duplex; + }; }; port@1 { diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt index 3d6d5fa0c4d5..cfe724398a12 100644 --- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt @@ -7,6 +7,7 @@ Required properties: - compatible: must be one of the following string: "allwinner,sun8i-a83t-emac" "allwinner,sun8i-h3-emac" + "allwinner,sun8i-r40-gmac" "allwinner,sun8i-v3s-emac" "allwinner,sun50i-a64-emac" - reg: address and length of the register for the device. @@ -20,18 +21,18 @@ Required properties: - phy-handle: See ethernet.txt - #address-cells: shall be 1 - #size-cells: shall be 0 -- syscon: A phandle to the syscon of the SoC with one of the following - compatible string: - - allwinner,sun8i-h3-system-controller - - allwinner,sun8i-v3s-system-controller - - allwinner,sun50i-a64-system-controller - - allwinner,sun8i-a83t-system-controller +- syscon: A phandle to the device containing the EMAC or GMAC clock register Optional properties: -- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0) -- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0) -Both delay properties need to be a multiple of 100. They control the delay for -external PHY. +- allwinner,tx-delay-ps: TX clock delay chain value in ps. + Range is 0-700. Default is 0. + Unavailable for allwinner,sun8i-r40-gmac +- allwinner,rx-delay-ps: RX clock delay chain value in ps. + Range is 0-3100. Default is 0. + Range is 0-700 for allwinner,sun8i-r40-gmac +Both delay properties need to be a multiple of 100. They control the +clock delay for external RGMII PHY. They do not apply to the internal +PHY or external non-RGMII PHYs. Optional properties for the following compatibles: - "allwinner,sun8i-h3-emac", diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index 79bf352e659c..047bdf7bdd2f 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -86,70 +86,4 @@ Example: * Gianfar PTP clock nodes -General Properties: - - - compatible Should be "fsl,etsec-ptp" - - reg Offset and length of the register set for the device - - interrupts There should be at least two interrupts. Some devices - have as many as four PTP related interrupts. - -Clock Properties: - - - fsl,cksel Timer reference clock source. - - fsl,tclk-period Timer reference clock period in nanoseconds. - - fsl,tmr-prsc Prescaler, divides the output clock. - - fsl,tmr-add Frequency compensation value. - - fsl,tmr-fiper1 Fixed interval period pulse generator. - - fsl,tmr-fiper2 Fixed interval period pulse generator. - - fsl,max-adj Maximum frequency adjustment in parts per billion. - - These properties set the operational parameters for the PTP - clock. You must choose these carefully for the clock to work right. - Here is how to figure good values: - - TimerOsc = selected reference clock MHz - tclk_period = desired clock period nanoseconds - NominalFreq = 1000 / tclk_period MHz - FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0) - tmr_add = ceil(2^32 / FreqDivRatio) - OutputClock = NominalFreq / tmr_prsc MHz - PulseWidth = 1 / OutputClock microseconds - FiperFreq1 = desired frequency in Hz - FiperDiv1 = 1000000 * OutputClock / FiperFreq1 - tmr_fiper1 = tmr_prsc * tclk_period * FiperDiv1 - tclk_period - max_adj = 1000000000 * (FreqDivRatio - 1.0) - 1 - - The calculation for tmr_fiper2 is the same as for tmr_fiper1. The - driver expects that tmr_fiper1 will be correctly set to produce a 1 - Pulse Per Second (PPS) signal, since this will be offered to the PPS - subsystem to synchronize the Linux clock. - - Reference clock source is determined by the value, which is holded - in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the - value, which will be directly written in those bits, that is why, - according to reference manual, the next clock sources can be used: - - <0> - external high precision timer reference clock (TSEC_TMR_CLK - input is used for this purpose); - <1> - eTSEC system clock; - <2> - eTSEC1 transmit clock; - <3> - RTC clock input. - - When this attribute is not used, eTSEC system clock will serve as - IEEE 1588 timer reference clock. - -Example: - - ptp_clock@24e00 { - compatible = "fsl,etsec-ptp"; - reg = <0x24E00 0xB0>; - interrupts = <12 0x8 13 0x8>; - interrupt-parent = < &ipic >; - fsl,cksel = <1>; - fsl,tclk-period = <10>; - fsl,tmr-prsc = <100>; - fsl,tmr-add = <0x999999A4>; - fsl,tmr-fiper1 = <0x3B9AC9F6>; - fsl,tmr-fiper2 = <0x00018696>; - fsl,max-adj = <659999998>; - }; +Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/net/ibm,emac.txt index 44b842b6ca15..44b842b6ca15 100644 --- a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt +++ b/Documentation/devicetree/bindings/net/ibm,emac.txt diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt index 61cada22ae6c..1321bb194ed9 100644 --- a/Documentation/devicetree/bindings/net/meson-dwmac.txt +++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt @@ -11,6 +11,7 @@ Required properties on all platforms: - "amlogic,meson8b-dwmac" - "amlogic,meson8m2-dwmac" - "amlogic,meson-gxbb-dwmac" + - "amlogic,meson-axg-dwmac" Additionally "snps,dwmac" and any applicable more detailed version number described in net/stmmac.txt should be used. diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index 42a248301615..e22d8cfea687 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -57,6 +57,13 @@ KSZ9031: - txd2-skew-ps : Skew control of TX data 2 pad - txd3-skew-ps : Skew control of TX data 3 pad + - micrel,force-master: + Boolean, force phy to master mode. Only set this option if the phy + reference clock provided at CLK125_NDO pin is used as MAC reference + clock because the clock jitter in slave mode is to high (errata#2). + Attention: The link partner must be configurable as slave otherwise + no link will be established. + Examples: mdio { diff --git a/Documentation/devicetree/bindings/net/microchip,lan78xx.txt b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt new file mode 100644 index 000000000000..76786a0f6d3d --- /dev/null +++ b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt @@ -0,0 +1,54 @@ +Microchip LAN78xx Gigabit Ethernet controller + +The LAN78XX devices are usually configured by programming their OTP or with +an external EEPROM, but some platforms (e.g. Raspberry Pi 3 B+) have neither. +The Device Tree properties, if present, override the OTP and EEPROM. + +Required properties: +- compatible: Should be one of "usb424,7800", "usb424,7801" or "usb424,7850". + +Optional properties: +- local-mac-address: see ethernet.txt +- mac-address: see ethernet.txt + +Optional properties of the embedded PHY: +- microchip,led-modes: a 0..4 element vector, with each element configuring + the operating mode of an LED. Omitted LEDs are turned off. Allowed values + are defined in "include/dt-bindings/net/microchip-lan78xx.h". + +Example: + +/* Based on the configuration for a Raspberry Pi 3 B+ */ +&usb { + usb-port@1 { + compatible = "usb424,2514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + usb-port@1 { + compatible = "usb424,2514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet: ethernet@1 { + compatible = "usb424,7800"; + reg = <1>; + local-mac-address = [ 00 11 22 33 44 55 ]; + + mdio { + #address-cells = <0x1>; + #size-cells = <0x0>; + eth_phy: ethernet-phy@1 { + reg = <1>; + microchip,led-modes = < + LAN78XX_LINK_1000_ACTIVITY + LAN78XX_LINK_10_100_ACTIVITY + >; + }; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/mscc-miim.txt b/Documentation/devicetree/bindings/net/mscc-miim.txt new file mode 100644 index 000000000000..7104679cf59d --- /dev/null +++ b/Documentation/devicetree/bindings/net/mscc-miim.txt @@ -0,0 +1,26 @@ +Microsemi MII Management Controller (MIIM) / MDIO +================================================= + +Properties: +- compatible: must be "mscc,ocelot-miim" +- reg: The base address of the MDIO bus controller register bank. Optionally, a + second register bank can be defined if there is an associated reset register + for internal PHYs +- #address-cells: Must be <1>. +- #size-cells: Must be <0>. MDIO addresses have no size component. +- interrupts: interrupt specifier (refer to the interrupt binding) + +Typically an MDIO bus might have several children. + +Example: + mdio@107009c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "mscc,ocelot-miim"; + reg = <0x107009c 0x36>, <0x10700f0 0x8>; + interrupts = <14>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt new file mode 100644 index 000000000000..0a84711abece --- /dev/null +++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt @@ -0,0 +1,82 @@ +Microsemi Ocelot network Switch +=============================== + +The Microsemi Ocelot network switch can be found on Microsemi SoCs (VSC7513, +VSC7514) + +Required properties: +- compatible: Should be "mscc,vsc7514-switch" +- reg: Must contain an (offset, length) pair of the register set for each + entry in reg-names. +- reg-names: Must include the following entries: + - "sys" + - "rew" + - "qs" + - "hsio" + - "qsys" + - "ana" + - "portX" with X from 0 to the number of last port index available on that + switch +- interrupts: Should contain the switch interrupts for frame extraction and + frame injection +- interrupt-names: should contain the interrupt names: "xtr", "inj" +- ethernet-ports: A container for child nodes representing switch ports. + +The ethernet-ports container has the following properties + +Required properties: + +- #address-cells: Must be 1 +- #size-cells: Must be 0 + +Each port node must have the following mandatory properties: +- reg: Describes the port address in the switch + +Port nodes may also contain the following optional standardised +properties, described in binding documents: + +- phy-handle: Phandle to a PHY on an MDIO bus. See + Documentation/devicetree/bindings/net/ethernet.txt for details. + +Example: + + switch@1010000 { + compatible = "mscc,vsc7514-switch"; + reg = <0x1010000 0x10000>, + <0x1030000 0x10000>, + <0x1080000 0x100>, + <0x10d0000 0x10000>, + <0x11e0000 0x100>, + <0x11f0000 0x100>, + <0x1200000 0x100>, + <0x1210000 0x100>, + <0x1220000 0x100>, + <0x1230000 0x100>, + <0x1240000 0x100>, + <0x1250000 0x100>, + <0x1260000 0x100>, + <0x1270000 0x100>, + <0x1280000 0x100>, + <0x1800000 0x80000>, + <0x1880000 0x10000>; + reg-names = "sys", "rew", "qs", "hsio", "port0", + "port1", "port2", "port3", "port4", "port5", + "port6", "port7", "port8", "port9", "port10", + "qsys", "ana"; + interrupts = <21 22>; + interrupt-names = "xtr", "inj"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port0: port@0 { + reg = <0>; + phy-handle = <&phy0>; + }; + port1: port@1 { + reg = <1>; + phy-handle = <&phy1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt new file mode 100644 index 000000000000..0ea18a53cc29 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt @@ -0,0 +1,30 @@ +Qualcomm Bluetooth Chips +--------------------- + +This documents the binding structure and common properties for serial +attached Qualcomm devices. + +Serial attached Qualcomm devices shall be a child node of the host UART +device the slave device is attached to. + +Required properties: + - compatible: should contain one of the following: + * "qcom,qca6174-bt" + +Optional properties: + - enable-gpios: gpio specifier used to enable chip + - clocks: clock provided to the controller (SUSCLK_32KHZ) + +Example: + +serial@7570000 { + label = "BT-UART"; + status = "okay"; + + bluetooth { + compatible = "qcom,qca6174-bt"; + + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index 890526dbfc26..fac897d54423 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -21,6 +21,7 @@ Required properties: - "renesas,etheravb-r8a77965" for the R8A77965 SoC. - "renesas,etheravb-r8a77970" for the R8A77970 SoC. - "renesas,etheravb-r8a77980" for the R8A77980 SoC. + - "renesas,etheravb-r8a77990" for the R8A77990 SoC. - "renesas,etheravb-r8a77995" for the R8A77995 SoC. - "renesas,etheravb-rcar-gen3" as a fallback for the above R-Car Gen3 devices. diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt index 929591d52ed6..832139919f20 100644 --- a/Documentation/devicetree/bindings/net/sff,sfp.txt +++ b/Documentation/devicetree/bindings/net/sff,sfp.txt @@ -7,11 +7,11 @@ Required properties: "sff,sfp" for SFP modules "sff,sff" for soldered down SFF modules -Optional Properties: - - i2c-bus : phandle of an I2C bus controller for the SFP two wire serial interface +Optional Properties: + - mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module presence input gpio signal, active (module absent) high. Must not be present for SFF modules diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt index 5172799a7f1a..82a4cf2c145d 100644 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -14,6 +14,7 @@ Required properties: "renesas,ether-r8a7791" if the device is a part of R8A7791 SoC. "renesas,ether-r8a7793" if the device is a part of R8A7793 SoC. "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,gether-r8a77980" if the device is a part of R8A77980 SoC. "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. "renesas,rcar-gen1-ether" for a generic R-Car Gen1 device. "renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1 diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt index 96398cc2982f..fc8f01718690 100644 --- a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt @@ -13,13 +13,25 @@ Required properties: - reg: Address where registers are mapped and size of region. - interrupts: Should contain the MAC interrupt. - phy-mode: See ethernet.txt in the same directory. Allow to choose - "rgmii", "rmii", or "mii" according to the PHY. + "rgmii", "rmii", "mii", or "internal" according to the PHY. + The acceptable mode is SoC-dependent. - phy-handle: Should point to the external phy device. See ethernet.txt file in the same directory. - clocks: A phandle to the clock for the MAC. + For Pro4 SoC, that is "socionext,uniphier-pro4-ave4", + another MAC clock, GIO bus clock and PHY clock are also required. + - clock-names: Should contain + - "ether", "ether-gb", "gio", "ether-phy" for Pro4 SoC + - "ether" for others + - resets: A phandle to the reset control for the MAC. For Pro4 SoC, + GIO bus reset is also required. + - reset-names: Should contain + - "ether", "gio" for Pro4 SoC + - "ether" for others + - socionext,syscon-phy-mode: A phandle to syscon with one argument + that configures phy mode. The argument is the ID of MAC instance. Optional properties: - - resets: A phandle to the reset control for the MAC. - local-mac-address: See ethernet.txt in the same directory. Required subnode: @@ -34,8 +46,11 @@ Example: interrupts = <0 66 4>; phy-mode = "rgmii"; phy-handle = <ðphy>; + clock-names = "ether"; clocks = <&sys_clk 6>; + reset-names = "ether"; resets = <&sys_rst 6>; + socionext,syscon-phy-mode = <&soc_glue 0>; local-mac-address = [00 00 00 00 00 00]; mdio { diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.txt b/Documentation/devicetree/bindings/net/stm32-dwmac.txt index 489dbcb66c5a..1341012722aa 100644 --- a/Documentation/devicetree/bindings/net/stm32-dwmac.txt +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.txt @@ -6,14 +6,28 @@ Please see stmmac.txt for the other unchanged properties. The device node has following properties. Required properties: -- compatible: Should be "st,stm32-dwmac" to select glue, and +- compatible: For MCU family should be "st,stm32-dwmac" to select glue, and "snps,dwmac-3.50a" to select IP version. + For MPU family should be "st,stm32mp1-dwmac" to select + glue, and "snps,dwmac-4.20a" to select IP version. - clocks: Must contain a phandle for each entry in clock-names. - clock-names: Should be "stmmaceth" for the host clock. Should be "mac-clk-tx" for the MAC TX clock. Should be "mac-clk-rx" for the MAC RX clock. + For MPU family need to add also "ethstp" for power mode clock and, + "syscfg-clk" for SYSCFG clock. +- interrupt-names: Should contain a list of interrupt names corresponding to + the interrupts in the interrupts property, if available. + Should be "macirq" for the main MAC IRQ + Should be "eth_wake_irq" for the IT which wake up system - st,syscon : Should be phandle/offset pair. The phandle to the syscon node which - encompases the glue register, and the offset of the control register. + encompases the glue register, and the offset of the control register. + +Optional properties: +- clock-names: For MPU family "mac-clk-ck" for PHY without quartz +- st,int-phyclk (boolean) : valid only where PHY do not have quartz and need to be clock + by RCC + Example: ethernet@40028000 { diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 3d2a031217da..7fd4e8ce4149 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be one of the following: * "qcom,ath10k" * "qcom,ipq4019-wifi" + * "qcom,wcn3990-wifi" PCI based devices uses compatible string "qcom,ath10k" and takes calibration data along with board specific data via "qcom,ath10k-calibration-data". @@ -18,8 +19,12 @@ In general, entry "qcom,ath10k-pre-calibration-data" and "qcom,ath10k-calibration-data" conflict with each other and only one can be provided per device. +SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi". + Optional properties: - reg: Address and length of the register set for the device. +- reg-names: Must include the list of following reg names, + "membase" - resets: Must contain an entry for each entry in reset-names. See ../reset/reseti.txt for details. - reset-names: Must include the list of following reset names, @@ -49,6 +54,8 @@ Optional properties: hw versions. - qcom,ath10k-pre-calibration-data : pre calibration data as an array, the length can vary between hw versions. +- <supply-name>-supply: handle to the regulator device tree node + optional "supply-name" is "vdd-0.8-cx-mx". Example (to supply the calibration data alone): @@ -119,3 +126,27 @@ wifi0: wifi@a000000 { qcom,msi_base = <0x40>; qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; }; + +Example (to supply wcn3990 SoC wifi block details): + +wifi@18000000 { + compatible = "qcom,wcn3990-wifi"; + reg = <0x18800000 0x800000>; + reg-names = "membase"; + clocks = <&clock_gcc clk_aggre2_noc_clk>; + clock-names = "smmu_aggre2_noc_clk" + interrupts = + <0 130 0 /* CE0 */ >, + <0 131 0 /* CE1 */ >, + <0 132 0 /* CE2 */ >, + <0 133 0 /* CE3 */ >, + <0 134 0 /* CE4 */ >, + <0 135 0 /* CE5 */ >, + <0 136 0 /* CE6 */ >, + <0 137 0 /* CE7 */ >, + <0 138 0 /* CE8 */ >, + <0 139 0 /* CE9 */ >, + <0 140 0 /* CE10 */ >, + <0 141 0 /* CE11 */ >; + vdd-0.8-cx-mx-supply = <&pm8998_l5>; +}; diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt index d69543701d5d..e319fe5e205a 100644 --- a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt +++ b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be one of the following: "allwinner,sun4i-a10-sid" "allwinner,sun7i-a20-sid" + "allwinner,sun8i-a83t-sid" "allwinner,sun8i-h3-sid" "allwinner,sun50i-a64-sid" diff --git a/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt b/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt new file mode 100644 index 000000000000..0df79d9e07ec --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt @@ -0,0 +1,40 @@ +Zodiac Inflight Innovations RAVE EEPROM Bindings + +RAVE SP EEPROM device is a "MFD cell" device exposing physical EEPROM +attached to RAVE Supervisory Processor. It is expected that its Device +Tree node is specified as a child of the node corresponding to the +parent RAVE SP device (as documented in +Documentation/devicetree/bindings/mfd/zii,rave-sp.txt) + +Required properties: + +- compatible: Should be "zii,rave-sp-eeprom" + +Optional properties: + +- zii,eeprom-name: Unique EEPROM identifier describing its function in the + system. Will be used as created NVMEM deivce's name. + +Data cells: + +Data cells are child nodes of eerpom node, bindings for which are +documented in Documentation/devicetree/bindings/nvmem/nvmem.txt + +Example: + + rave-sp { + compatible = "zii,rave-sp-rdu1"; + current-speed = <38400>; + + eeprom@a4 { + compatible = "zii,rave-sp-eeprom"; + reg = <0xa4 0x4000>; + #address-cells = <1>; + #size-cells = <1>; + zii,eeprom-name = "main-eeprom"; + + wdt_timeout: wdt-timeout@81 { + reg = <0x81 2>; + }; + }; + } diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt new file mode 100644 index 000000000000..c2127b96805a --- /dev/null +++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt @@ -0,0 +1,680 @@ +Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings +=================================== + +In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996 +that have KRYO processors, the CPU ferequencies subset and voltage value +of each OPP varies based on the silicon variant in use. +Qualcomm Technologies, Inc. Process Voltage Scaling Tables +defines the voltage and frequency value based on the msm-id in SMEM +and speedbin blown in the efuse combination. +The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC +to provide the OPP framework with required information (existing HW bitmap). +This is used to determine the voltage and frequency value for each OPP of +operating-points-v2 table when it is parsed by the OPP framework. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use. + +In 'operating-points-v2' table: +- compatible: Should be + - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996. +- nvmem-cells: A phandle pointing to a nvmem-cells node representing the + efuse registers that has information about the + speedbin that is used to select the right frequency/voltage + value pair. + Please refer the for nvmem-cells + bindings Documentation/devicetree/bindings/nvmem/nvmem.txt + and also examples below. + +In every OPP node: +- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW. + Bitmap: + 0: MSM8996 V3, speedbin 0 + 1: MSM8996 V3, speedbin 1 + 2: MSM8996 V3, speedbin 2 + 3: unused + 4: MSM8996 SG, speedbin 0 + 5: MSM8996 SG, speedbin 1 + 6: MSM8996 SG, speedbin 2 + 7-31: unused + +Example 1: +--------- + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x0>; + enable-method = "psci"; + clocks = <&kryocc 0>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x1>; + enable-method = "psci"; + clocks = <&kryocc 0>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x100>; + enable-method = "psci"; + clocks = <&kryocc 1>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster1_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_1>; + L2_1: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x101>; + enable-method = "psci"; + clocks = <&kryocc 1>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster1_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_1>; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + }; + + cluster1 { + core0 { + cpu = <&CPU2>; + }; + + core1 { + cpu = <&CPU3>; + }; + }; + }; + }; + + cluster0_opp: opp_table0 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp-307200000 { + opp-hz = /bits/ 64 <307200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-422400000 { + opp-hz = /bits/ 64 <422400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-460800000 { + opp-hz = /bits/ 64 <460800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-537600000 { + opp-hz = /bits/ 64 <537600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-556800000 { + opp-hz = /bits/ 64 <556800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-614400000 { + opp-hz = /bits/ 64 <614400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-652800000 { + opp-hz = /bits/ 64 <652800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-691200000 { + opp-hz = /bits/ 64 <691200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-729600000 { + opp-hz = /bits/ 64 <729600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-768000000 { + opp-hz = /bits/ 64 <768000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-844800000 { + opp-hz = /bits/ 64 <844800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-902400000 { + opp-hz = /bits/ 64 <902400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-960000000 { + opp-hz = /bits/ 64 <960000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-979200000 { + opp-hz = /bits/ 64 <979200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1132800000 { + opp-hz = /bits/ 64 <1132800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1190400000 { + opp-hz = /bits/ 64 <1190400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1228800000 { + opp-hz = /bits/ 64 <1228800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1324800000 { + opp-hz = /bits/ 64 <1324800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x5>; + clock-latency-ns = <200000>; + }; + opp-1363200000 { + opp-hz = /bits/ 64 <1363200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x72>; + clock-latency-ns = <200000>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x5>; + clock-latency-ns = <200000>; + }; + opp-1440000000 { + opp-hz = /bits/ 64 <1440000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-1497600000 { + opp-hz = /bits/ 64 <1497600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x4>; + clock-latency-ns = <200000>; + }; + opp-1516800000 { + opp-hz = /bits/ 64 <1516800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1593600000 { + opp-hz = /bits/ 64 <1593600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x71>; + clock-latency-ns = <200000>; + }; + opp-1996800000 { + opp-hz = /bits/ 64 <1996800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x20>; + clock-latency-ns = <200000>; + }; + opp-2188800000 { + opp-hz = /bits/ 64 <2188800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + }; + + cluster1_opp: opp_table1 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp-307200000 { + opp-hz = /bits/ 64 <307200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-403200000 { + opp-hz = /bits/ 64 <403200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-460800000 { + opp-hz = /bits/ 64 <460800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-537600000 { + opp-hz = /bits/ 64 <537600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-556800000 { + opp-hz = /bits/ 64 <556800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-614400000 { + opp-hz = /bits/ 64 <614400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-652800000 { + opp-hz = /bits/ 64 <652800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-691200000 { + opp-hz = /bits/ 64 <691200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-729600000 { + opp-hz = /bits/ 64 <729600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-748800000 { + opp-hz = /bits/ 64 <748800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-806400000 { + opp-hz = /bits/ 64 <806400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-825600000 { + opp-hz = /bits/ 64 <825600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-883200000 { + opp-hz = /bits/ 64 <883200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-902400000 { + opp-hz = /bits/ 64 <902400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-940800000 { + opp-hz = /bits/ 64 <940800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-979200000 { + opp-hz = /bits/ 64 <979200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1132800000 { + opp-hz = /bits/ 64 <1132800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1190400000 { + opp-hz = /bits/ 64 <1190400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1248000000 { + opp-hz = /bits/ 64 <1248000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1324800000 { + opp-hz = /bits/ 64 <1324800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1363200000 { + opp-hz = /bits/ 64 <1363200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1440000000 { + opp-hz = /bits/ 64 <1440000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1516800000 { + opp-hz = /bits/ 64 <1516800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1555200000 { + opp-hz = /bits/ 64 <1555200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1593600000 { + opp-hz = /bits/ 64 <1593600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1632000000 { + opp-hz = /bits/ 64 <1632000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1670400000 { + opp-hz = /bits/ 64 <1670400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1708800000 { + opp-hz = /bits/ 64 <1708800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1747200000 { + opp-hz = /bits/ 64 <1747200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1785600000 { + opp-hz = /bits/ 64 <1785600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1804800000 { + opp-hz = /bits/ 64 <1804800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x6>; + clock-latency-ns = <200000>; + }; + opp-1824000000 { + opp-hz = /bits/ 64 <1824000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x71>; + clock-latency-ns = <200000>; + }; + opp-1900800000 { + opp-hz = /bits/ 64 <1900800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x74>; + clock-latency-ns = <200000>; + }; + opp-1920000000 { + opp-hz = /bits/ 64 <1920000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-1977600000 { + opp-hz = /bits/ 64 <1977600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x30>; + clock-latency-ns = <200000>; + }; + opp-1996800000 { + opp-hz = /bits/ 64 <1996800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-2054400000 { + opp-hz = /bits/ 64 <2054400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x30>; + clock-latency-ns = <200000>; + }; + opp-2073600000 { + opp-hz = /bits/ 64 <2073600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-2150400000 { + opp-hz = /bits/ 64 <2150400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x31>; + clock-latency-ns = <200000>; + }; + opp-2246400000 { + opp-hz = /bits/ 64 <2246400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + opp-2342400000 { + opp-hz = /bits/ 64 <2342400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + }; + +.... + +reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; +.... + smem_mem: smem-mem@86000000 { + reg = <0x0 0x86000000 0x0 0x200000>; + no-map; + }; +.... +}; + +smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; +}; + +soc { +.... + qfprom: qfprom@74000 { + compatible = "qcom,qfprom"; + reg = <0x00074000 0x8ff>; + #address-cells = <1>; + #size-cells = <1>; + .... + speedbin_efuse: speedbin@133 { + reg = <0x133 0x1>; + bits = <5 3>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 4e4f30288c8b..c396c4c0af92 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -82,7 +82,10 @@ This defines voltage-current-frequency combinations along with other related properties. Required properties: -- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer. +- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer. This is a + required property for all device nodes but devices like power domains. The + power domain nodes must have another (implementation dependent) property which + uniquely identifies the OPP nodes. Optional properties: - opp-microvolt: voltage in micro Volts. @@ -159,7 +162,7 @@ Optional properties: - status: Marks the node enabled/disabled. -- required-opp: This contains phandle to an OPP node in another device's OPP +- required-opps: This contains phandle to an OPP node in another device's OPP table. It may contain an array of phandles, where each phandle points to an OPP of a different device. It should not contain multiple phandles to the OPP nodes in the same OPP table. This specifies the minimum required OPP of the diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 1da7ade3183c..c124f9bc11f3 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -1,7 +1,9 @@ * Synopsys DesignWare PCIe interface Required properties: -- compatible: should contain "snps,dw-pcie" to identify the core. +- compatible: + "snps,dw-pcie" for RC mode; + "snps,dw-pcie-ep" for EP mode; - reg: Should contain the configuration address space. - reg-names: Must be "config" for the PCIe configuration space. (The old way of getting the configuration address space from "ranges" @@ -41,11 +43,11 @@ EP mode: Example configuration: - pcie: pcie@dffff000 { + pcie: pcie@dfc00000 { compatible = "snps,dw-pcie"; - reg = <0xdffff000 0x1000>, /* Controller registers */ - <0xd0000000 0x2000>; /* PCI config space */ - reg-names = "ctrlreg", "config"; + reg = <0xdfc00000 0x0001000>, /* IP registers */ + <0xd0000000 0x0002000>; /* Configuration space */ + reg-names = "dbi", "config"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; @@ -54,5 +56,15 @@ Example configuration: interrupts = <25>, <24>; #interrupt-cells = <1>; num-lanes = <1>; - num-viewport = <3>; + }; +or + pcie: pcie@dfc00000 { + compatible = "snps,dw-pcie-ep"; + reg = <0xdfc00000 0x0001000>, /* IP registers 1 */ + <0xdfc01000 0x0001000>, /* IP registers 2 */ + <0xd0000000 0x2000000>; /* Configuration space */ + reg-names = "dbi", "dbi2", "addr_space"; + num-ib-windows = <6>; + num-ob-windows = <2>; + num-lanes = <1>; }; diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index 7bf9df047a1e..0dcb87d6554f 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -3,7 +3,7 @@ HiSilicon Hip05 and Hip06 PCIe host bridge DT description HiSilicon PCIe host controller is based on the Synopsys DesignWare PCI core. It shares common functions with the PCIe DesignWare core driver and inherits common properties defined in -Documentation/devicetree/bindings/pci/designware-pci.txt. +Documentation/devicetree/bindings/pci/designware-pcie.txt. Additional properties are described here: diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt index 6e217c63123d..6bbe43818ad5 100644 --- a/Documentation/devicetree/bindings/pci/kirin-pcie.txt +++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt @@ -3,7 +3,7 @@ HiSilicon Kirin SoCs PCIe host DT description Kirin PCIe host controller is based on the Synopsys DesignWare PCI core. It shares common functions with the PCIe DesignWare core driver and inherits common properties defined in -Documentation/devicetree/bindings/pci/designware-pci.txt. +Documentation/devicetree/bindings/pci/designware-pcie.txt. Additional properties are described here: diff --git a/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt b/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt new file mode 100644 index 000000000000..65038aa642e5 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt @@ -0,0 +1,73 @@ +* Mobiveil AXI PCIe Root Port Bridge DT description + +Mobiveil's GPEX 4.0 is a PCIe Gen4 root port bridge IP. This configurable IP +has up to 8 outbound and inbound windows for the address translation. + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "mbvl,gpex40-pcie" +- reg: Should contain PCIe registers location and length + "config_axi_slave": PCIe controller registers + "csr_axi_slave" : Bridge config registers + "gpio_slave" : GPIO registers to control slot power + "apb_csr" : MSI registers + +- device_type: must be "pci" +- apio-wins : number of requested apio outbound windows + default 2 outbound windows are configured - + 1. Config window + 2. Memory window +- ppio-wins : number of requested ppio inbound windows + default 1 inbound memory window is configured. +- bus-range: PCI bus numbers covered +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- interrupt-parent : phandle to the interrupt controller that + it is attached to, it should be set to gic to point to + ARM's Generic Interrupt Controller node in system DT. +- interrupts: The interrupt line of the PCIe controller + last cell of this field is set to 4 to + denote it as IRQ_TYPE_LEVEL_HIGH type interrupt. +- interrupt-map-mask, + interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation + + +Example: +++++++++ + pcie0: pcie@a0000000 { + #address-cells = <3>; + #size-cells = <2>; + compatible = "mbvl,gpex40-pcie"; + reg = <0xa0000000 0x00001000>, + <0xb0000000 0x00010000>, + <0xff000000 0x00200000>, + <0xb0010000 0x00001000>; + reg-names = "config_axi_slave", + "csr_axi_slave", + "gpio_slave", + "apb_csr"; + device_type = "pci"; + apio-wins = <2>; + ppio-wins = <1>; + bus-range = <0x00000000 0x000000ff>; + interrupt-controller; + interrupt-parent = <&gic>; + #interrupt-cells = <1>; + interrupts = < 0 89 4 >; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 0 &pci_express 0>, + <0 0 0 1 &pci_express 1>, + <0 0 0 2 &pci_express 2>, + <0 0 0 3 &pci_express 3>; + ranges = < 0x83000000 0 0x00000000 0xa8000000 0 0x8000000>; + + }; diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt index c1e4c3d10a74..9e3fc15e1af8 100644 --- a/Documentation/devicetree/bindings/pci/pci-armada8k.txt +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -12,7 +12,10 @@ Required properties: - "ctrl" for the control register region - "config" for the config space region - interrupts: Interrupt specifier for the PCIe controler -- clocks: reference to the PCIe controller clock +- clocks: reference to the PCIe controller clocks +- clock-names: mandatory if there is a second clock, in this case the + name must be "core" for the first clock and "reg" for the second + one Example: diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index 7e05487544ed..3d4a209b0fd0 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -3,9 +3,9 @@ TI Keystone PCIe interface Keystone PCI host Controller is based on the Synopsys DesignWare PCI hardware version 3.65. It shares common functions with the PCIe DesignWare core driver and inherits common properties defined in -Documentation/devicetree/bindings/pci/designware-pci.txt +Documentation/devicetree/bindings/pci/designware-pcie.txt -Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt +Please refer to Documentation/devicetree/bindings/pci/designware-pcie.txt for the details of DesignWare DT bindings. Additional properties are described here as well as properties that are not applicable. diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 1fb614e615da..a5f7fc62d10e 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -8,6 +8,7 @@ compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a7793" for the R8A7793 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-r8a7796" for the R8A7796 SoC; + "renesas,pcie-r8a77980" for the R8A77980 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or RZ/G1 compatible device. "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. @@ -32,6 +33,11 @@ compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; and PCIe bus clocks. - clock-names: from common clock binding: should be "pcie" and "pcie_bus". +Optional properties: +- phys: from common PHY binding: PHY phandle and specifier (only make sense + for R-Car gen3 SoCs where the PCIe PHYs have their own register blocks). +- phy-names: from common PHY binding: should be "pcie". + Example: SoC-specific DT Entry: diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie-ep.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie-ep.txt new file mode 100644 index 000000000000..778467307a93 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie-ep.txt @@ -0,0 +1,62 @@ +* Rockchip AXI PCIe Endpoint Controller DT description + +Required properties: +- compatible: Should contain "rockchip,rk3399-pcie-ep" +- reg: Two register ranges as listed in the reg-names property +- reg-names: Must include the following names + - "apb-base" + - "mem-base" +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "aclk" + - "aclk-perf" + - "hclk" + - "pm" +- resets: Must contain seven entries for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following names + - "core" + - "mgmt" + - "mgmt-sticky" + - "pipe" + - "pm" + - "aclk" + - "pclk" +- pinctrl-names : The pin control state names +- pinctrl-0: The "default" pinctrl state +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include 4 entries for all 4 lanes even if some of + them won't be used for your cases. Entries are of the form "pcie-phy-N": + where N ranges from 0 to 3. + (see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt + for changing the #phy-cells of phy node to support it) +- rockchip,max-outbound-regions: Maximum number of outbound regions + +Optional Property: +- num-lanes: number of lanes to use +- max-functions: Maximum number of functions that can be configured (default 1). + +pcie0-ep: pcie@f8000000 { + compatible = "rockchip,rk3399-pcie-ep"; + #address-cells = <3>; + #size-cells = <2>; + rockchip,max-outbound-regions = <16>; + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; + clock-names = "aclk", "aclk-perf", + "hclk", "pm"; + max-functions = /bits/ 8 <8>; + num-lanes = <4>; + reg = <0x0 0xfd000000 0x0 0x1000000>, <0x0 0x80000000 0x0 0x20000>; + reg-names = "apb-base", "mem-base"; + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> , + <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe", + "pm", "pclk", "aclk"; + phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>; + phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3"; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreq>; +}; diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie-host.txt index af34c65773fd..af34c65773fd 100644 --- a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie-host.txt diff --git a/Documentation/devicetree/bindings/pci/xgene-pci.txt b/Documentation/devicetree/bindings/pci/xgene-pci.txt index 6fd2decfa66c..92490330dc1c 100644 --- a/Documentation/devicetree/bindings/pci/xgene-pci.txt +++ b/Documentation/devicetree/bindings/pci/xgene-pci.txt @@ -25,8 +25,6 @@ Optional properties: Example: -SoC-specific DT Entry: - pcie0: pcie@1f2b0000 { status = "disabled"; device_type = "pci"; @@ -50,8 +48,3 @@ SoC-specific DT Entry: clocks = <&pcie0clk 0>; }; - -Board-specific DT Entry: - &pcie0 { - status = "ok"; - }; diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt new file mode 100644 index 000000000000..e7caefa0b9c2 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt @@ -0,0 +1,109 @@ +MediaTek XS-PHY binding +-------------------------- + +The XS-PHY controller supports physical layer functionality for USB3.1 +GEN2 controller on MediaTek SoCs. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy", + soc-model is the name of SoC, such as mt3611 etc; + when using "mediatek,xsphy" compatible string, you need SoC specific + ones in addition, one of: + - "mediatek,mt3611-xsphy" + + - #address-cells, #size-cells : should use the same values as the root node + - ranges: must be present + +Optional properties (controller (parent) node): + - reg : offset and length of register shared by multiple U3 ports, + exclude port's private register, if only U2 ports provided, + shouldn't use the property. + - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate + calibrate + - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on + SoC process + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names +- clock-names : must contain + "ref": 48M reference clock for HighSpeed analog phy; and 26M + reference clock for SuperSpeedPlus analog phy, sometimes is + 24M, 25M or 27M, depended on platform. +- #phy-cells : should be 1 + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +The following optional properties are only for debug or HQA test +Optional properties (PHY_TYPE_USB2 port (child) node): +- mediatek,eye-src : u32, the value of slew rate calibrate +- mediatek,eye-vrt : u32, the selection of VRT reference voltage +- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage +- mediatek,efuse-intr : u32, the selection of Internal Resistor + +Optional properties (PHY_TYPE_USB3 port (child) node): +- mediatek,efuse-intr : u32, the selection of Internal Resistor +- mediatek,efuse-tx-imp : u32, the selection of TX Impedance +- mediatek,efuse-rx-imp : u32, the selection of RX Impedance + +Banks layout of xsphy +------------------------------------------------------------- +port offset bank +u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM +u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM +u2 port2 0x2000 MISC + ... +u31 common 0x3000 DIG_GLB + 0x3100 PHYA_GLB +u31 port0 0x3400 DIG_LN_TOP + 0x3500 DIG_LN_TX0 + 0x3600 DIG_LN_RX0 + 0x3700 DIG_LN_DAIF + 0x3800 PHYA_LN +u31 port1 0x3a00 DIG_LN_TOP + 0x3b00 DIG_LN_TX0 + 0x3c00 DIG_LN_RX0 + 0x3d00 DIG_LN_DAIF + 0x3e00 PHYA_LN + ... + +DIG_GLB & PHYA_GLB are shared by U31 ports. + +Example: + +u3phy: usb-phy@11c40000 { + compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy"; + reg = <0 0x11c43000 0 0x0200>; + mediatek,src-ref-clk-mhz = <26>; + mediatek,src-coef = <17>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + u2port0: usb-phy@11c40000 { + reg = <0 0x11c40000 0 0x0400>; + clocks = <&clk48m>; + clock-names = "ref"; + mediatek,eye-src = <4>; + #phy-cells = <1>; + }; + + u3port0: usb-phy@11c43000 { + reg = <0 0x11c43400 0 0x0500>; + clocks = <&clk26m>; + clock-names = "ref"; + mediatek,efuse-intr = <28>; + #phy-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index dcf1b8f691d5..266a1bb8bb6e 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -9,7 +9,8 @@ Required properties: "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074 "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996, - "qcom,qmp-v3-usb3-phy" for USB3 QMP V3 phy. + "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845, + "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845. - reg: offset and length of register set for PHY's common serdes block. diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt index 42c97426836e..03025d97998b 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt @@ -6,7 +6,7 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets. Required properties: - compatible: compatible list, contains "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996, - "qcom,qusb2-v2-phy" for QUSB2 V2 PHY. + "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845. - reg: offset and length of the PHY register set. - #phy-cells: must be 0. @@ -27,6 +27,27 @@ Optional properties: tuning parameter value for qusb2 phy. - qcom,tcsr-syscon: Phandle to TCSR syscon register region. + - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be + added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY + tuning parameter that may vary for different boards of same SOC. + This property is applicable to only QUSB2 v2 PHY (sdm845). + - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX + output current. + Possible range is - 15mA to 24mA (stepsize of 600 uA). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is 22.2mA for sdm845. + - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level. + Possible range is 0 to 15% (stepsize of 5%). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is 10% for sdm845. +- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX + pre-emphasis (specified using qcom,preemphasis-level) must be in + effect. Duration could be half-bit of full-bit. + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is full-bit width for sdm845. Example: hsusb_phy: phy@7411000 { diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s900-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s900-pinctrl.txt index fb87c7d74f2e..8fb5a53775e8 100644 --- a/Documentation/devicetree/bindings/pinctrl/actions,s900-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/actions,s900-pinctrl.txt @@ -8,6 +8,17 @@ Required Properties: - reg: Should contain the register base address and size of the pin controller. - clocks: phandle of the clock feeding the pin controller +- gpio-controller: Marks the device node as a GPIO controller. +- gpio-ranges: Specifies the mapping between gpio controller and + pin-controller pins. +- #gpio-cells: Should be two. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell + defines the interrupt number, the second encodes + the trigger flags described in + bindings/interrupt-controller/interrupts.txt Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the @@ -164,6 +175,11 @@ Example: compatible = "actions,s900-pinctrl"; reg = <0x0 0xe01b0000 0x0 0x1000>; clocks = <&cmu CLK_GPIO>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 146>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; uart2-default: uart2-default { pinmux { diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 64bc5c2a76da..258a4648ab81 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -28,6 +28,7 @@ Required properties: "allwinner,sun50i-a64-r-pinctrl" "allwinner,sun50i-h5-pinctrl" "allwinner,sun50i-h6-pinctrl" + "allwinner,sun50i-h6-r-pinctrl" "nextthing,gr8-pinctrl" - reg: Should contain the register physical address and length for the diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt index 2569866c692f..3fac0a061bcc 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt @@ -36,6 +36,24 @@ listed. In other words, a subnode that lists only a mux function implies no information about any pull configuration. Similarly, a subnode that lists only a pul parameter implies no information about the mux function. +The BCM2835 pin configuration and multiplexing supports the generic bindings. +For details on each properties, you can refer to ./pinctrl-bindings.txt. + +Required sub-node properties: + - pins + - function + +Optional sub-node properties: + - bias-disable + - bias-pull-up + - bias-pull-down + - output-high + - output-low + +Legacy pin configuration and multiplexing binding: +*** (Its use is deprecated, use generic multiplexing and configuration +bindings instead) + Required subnode-properties: - brcm,pins: An array of cells. Each cell contains the ID of a pin. Valid IDs are the integer GPIO IDs; 0==GPIO0, 1==GPIO1, ... 53==GPIO53. diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 2c12f9789116..54ecb8ab7788 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -3,8 +3,10 @@ Required properties for the root node: - compatible: one of "amlogic,meson8-cbus-pinctrl" "amlogic,meson8b-cbus-pinctrl" + "amlogic,meson8m2-cbus-pinctrl" "amlogic,meson8-aobus-pinctrl" "amlogic,meson8b-aobus-pinctrl" + "amlogic,meson8m2-aobus-pinctrl" "amlogic,meson-gxbb-periphs-pinctrl" "amlogic,meson-gxbb-aobus-pinctrl" "amlogic,meson-gxl-periphs-pinctrl" diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt index ad4fce3552bb..511fc234558b 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt @@ -11,9 +11,9 @@ Optional Pinmux properties: -------------------------- Following properties are required if default setting of pins are required at boot. -- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>. - pinctrl[0...n]: Properties to contain the phandle for pinctrl states per - <pinctrl-binding.txt>. + <pinctrl-bindings.txt>. The pin configurations are defined as child of the pinctrl states node. Each sub-node have following properties: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt index a5a8322a31bd..625a22e2f211 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt @@ -18,7 +18,9 @@ Required properties: removed. - #gpio-cells : Should be two. - first cell is the pin number - - second cell is used to specify flags. Flags are currently unused. + - second cell is used to specify flags as described in + 'Documentation/devicetree/bindings/gpio/gpio.txt'. Allowed values defined by + 'include/dt-bindings/gpio/gpio.h' (e.g. GPIO_ACTIVE_LOW). - gpio-controller : Marks the device node as a GPIO controller. - reg : For an address on its bus. I2C uses this a the I2C address of the chip. SPI uses this to specify the chipselect line which the chip is @@ -99,9 +101,9 @@ Optional Pinmux properties: -------------------------- Following properties are required if default setting of pins are required at boot. -- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>. - pinctrl[0...n]: Properties to contain the phandle for pinctrl states per - <pinctrl-binding.txt>. + <pinctrl-bindings.txt>. The pin configurations are defined as child of the pinctrl states node. Each sub-node have following properties: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt index f18ed99f6e14..def8fcad8941 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt @@ -9,6 +9,16 @@ Required properties for the root node: - #gpio-cells: Should be two. The first cell is the pin number and the second is the GPIO flags. +Optional properties: +- interrupt-controller : Marks the device node as an interrupt controller + +If the property interrupt-controller is defined, following property is required +- reg-names: A string describing the "reg" entries. Must contain "eint". +- interrupts : The interrupt output from the controller. +- #interrupt-cells: Should be two. +- interrupt-parent: Phandle of the interrupt parent to which the external + GPIO interrupts are forwarded to. + Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt index eee3dc260934..cbcbd31e3ce8 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt @@ -10,9 +10,9 @@ Optional Pinmux properties: -------------------------- Following properties are required if default setting of pins are required at boot. -- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>. - pinctrl[0...n]: Properties to contain the phandle for pinctrl states per - <pinctrl-binding.txt>. + <pinctrl-bindings.txt>. The pin configurations are defined as child of the pinctrl states node. Each sub-node have following properties: diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 892d8fd7b700..abd8fbcf1e62 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -15,6 +15,7 @@ Required Properties: - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. - "renesas,pfc-r8a7743": for R8A7743 (RZ/G1M) compatible pin-controller. - "renesas,pfc-r8a7745": for R8A7745 (RZ/G1E) compatible pin-controller. + - "renesas,pfc-r8a77470": for R8A77470 (RZ/G1C) compatible pin-controller. - "renesas,pfc-r8a7778": for R8A7778 (R-Car M1) compatible pin-controller. - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. @@ -27,6 +28,7 @@ Required Properties: - "renesas,pfc-r8a77965": for R8A77965 (R-Car M3-N) compatible pin-controller. - "renesas,pfc-r8a77970": for R8A77970 (R-Car V3M) compatible pin-controller. - "renesas,pfc-r8a77980": for R8A77980 (R-Car V3H) compatible pin-controller. + - "renesas,pfc-r8a77990": for R8A77990 (R-Car E3) compatible pin-controller. - "renesas,pfc-r8a77995": for R8A77995 (R-Car D3) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index a01a3b8a2363..0919db294c17 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -20,6 +20,7 @@ defined as gpio sub-nodes of the pinmux controller. Required properties for iomux controller: - compatible: should be + "rockchip,px30-pinctrl": for Rockchip PX30 "rockchip,rv1108-pinctrl": for Rockchip RV1108 "rockchip,rk2928-pinctrl": for Rockchip RK2928 "rockchip,rk3066a-pinctrl": for Rockchip RK3066a diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt index b31d6bbeee16..726ec2875223 100644 --- a/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt +++ b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt @@ -14,7 +14,7 @@ Required properties: datasheet - interrupts: Should contain one interrupt specifier for the GPC interrupt - clocks: Must contain an entry for each entry in clock-names. - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. - clock-names: Must include the following entries: - ipg diff --git a/Documentation/devicetree/bindings/power/pd-samsung.txt b/Documentation/devicetree/bindings/power/pd-samsung.txt index 549f7dee9b9d..92ef355e8f64 100644 --- a/Documentation/devicetree/bindings/power/pd-samsung.txt +++ b/Documentation/devicetree/bindings/power/pd-samsung.txt @@ -15,23 +15,13 @@ Required Properties: Optional Properties: - label: Human readable string with domain name. Will be visible in userspace to let user to distinguish between multiple domains in SoC. -- clocks: List of clock handles. The parent clocks of the input clocks to the - devices in this power domain are set to oscclk before power gating - and restored back after powering on a domain. This is required for - all domains which are powered on and off and not required for unused - domains. -- clock-names: The following clocks can be specified: - - oscclk: Oscillator clock. - - clkN: Input clocks to the devices in this power domain. These clocks - will be reparented to oscclk before switching power domain off. - Their original parent will be brought back after turning on - the domain. Maximum of 4 clocks (N = 0 to 3) are supported. - - asbN: Clocks required by asynchronous bridges (ASB) present in - the power domain. These clock should be enabled during power - domain on/off operations. - power-domains: phandle pointing to the parent power domain, for more details see Documentation/devicetree/bindings/power/power_domain.txt +Deprecated Properties: +- clocks +- clock-names + Node of a device using power domains must have a power-domains property defined with a phandle to respective power domain. @@ -47,8 +37,6 @@ Example: mfc_pd: power-domain@10044060 { compatible = "samsung,exynos4210-pd"; reg = <0x10044060 0x20>; - clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_USER_ACLK333>; - clock-names = "oscclk", "clk0"; #power-domain-cells = <0>; label = "MFC"; }; diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index f3355313c020..9b387f861aed 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -111,8 +111,8 @@ Example 3: ==PM domain consumers== Required properties: - - power-domains : A phandle and PM domain specifier as defined by bindings of - the power controller specified by phandle. + - power-domains : A list of PM domain specifiers, as defined by bindings of + the power controller that is the PM domain provider. Example: @@ -122,12 +122,21 @@ Example: power-domains = <&power 0>; }; -The node above defines a typical PM domain consumer device, which is located -inside a PM domain with index 0 of a power controller represented by a node -with the label "power". + leaky-device@12351000 { + compatible = "foo,i-leak-current"; + reg = <0x12351000 0x1000>; + power-domains = <&power 0>, <&power 1> ; + }; + +The first example above defines a typical PM domain consumer device, which is +located inside a PM domain with index 0 of a power controller represented by a +node with the label "power". +In the second example the consumer device are partitioned across two PM domains, +the first with index 0 and the second with index 1, of a power controller that +is represented by a node with the label "power. Optional properties: -- required-opp: This contains phandle to an OPP node in another device's OPP +- required-opps: This contains phandle to an OPP node in another device's OPP table. It may contain an array of phandles, where each phandle points to an OPP of a different device. It should not contain multiple phandles to the OPP nodes in the same OPP table. This specifies the minimum required OPP of the @@ -175,14 +184,14 @@ Example: compatible = "foo,i-leak-current"; reg = <0x12350000 0x1000>; power-domains = <&power 0>; - required-opp = <&domain0_opp_0>; + required-opps = <&domain0_opp_0>; }; leaky-device1@12350000 { compatible = "foo,i-leak-current"; reg = <0x12350000 0x1000>; power-domains = <&power 1>; - required-opp = <&domain1_opp_1>; + required-opps = <&domain1_opp_1>; }; [1]. Documentation/devicetree/bindings/power/domain-idle-state.txt diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index ab399e559257..180ae65be753 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -9,6 +9,7 @@ Required properties: - compatible: Must contain exactly one of the following: - "renesas,r8a7743-sysc" (RZ/G1M) - "renesas,r8a7745-sysc" (RZ/G1E) + - "renesas,r8a77470-sysc" (RZ/G1C) - "renesas,r8a7779-sysc" (R-Car H1) - "renesas,r8a7790-sysc" (R-Car H2) - "renesas,r8a7791-sysc" (R-Car M2-W) @@ -20,6 +21,7 @@ Required properties: - "renesas,r8a77965-sysc" (R-Car M3-N) - "renesas,r8a77970-sysc" (R-Car V3M) - "renesas,r8a77980-sysc" (R-Car V3H) + - "renesas,r8a77990-sysc" (R-Car E3) - "renesas,r8a77995-sysc" (R-Car D3) - reg: Address start and address range for the device. - #power-domain-cells: Must be 1. diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index 4a4766e9c254..e66fd4eab71c 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -31,6 +31,8 @@ SoC is on the same page. Required properties: - compatible: should be one of: + - "rockchip,px30-io-voltage-domain" for px30 + - "rockchip,px30-pmu-io-voltage-domain" for px30 pmu-domains - "rockchip,rk3188-io-voltage-domain" for rk3188 - "rockchip,rk3228-io-voltage-domain" for rk3228 - "rockchip,rk3288-io-voltage-domain" for rk3288 @@ -51,6 +53,19 @@ a phandle the relevant regulator. All specified supplies must be able to report their voltage. The IO Voltage Domain for any non-specified supplies will be not be touched. +Possible supplies for PX30: +- vccio6-supply: The supply connected to VCCIO6. +- vccio1-supply: The supply connected to VCCIO1. +- vccio2-supply: The supply connected to VCCIO2. +- vccio3-supply: The supply connected to VCCIO3. +- vccio4-supply: The supply connected to VCCIO4. +- vccio5-supply: The supply connected to VCCIO5. +- vccio-oscgpi-supply: The supply connected to VCCIO_OSCGPI. + +Possible supplies for PX30 pmu-domains: +- pmuio1-supply: The supply connected to PMUIO1. +- pmuio2-supply: The supply connected to PMUIO2. + Possible supplies for rk3188: - ap0-supply: The supply connected to AP0_VCC. - ap1-supply: The supply connected to AP1_VCC. diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt index 0ba1bcc7f33a..f181e46d8e07 100644 --- a/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt +++ b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt @@ -13,4 +13,4 @@ Required Properties: }; For information on battery specific node, Ref: -Documentation/devicetree/bindings/power_supply/ab8500/fg.txt +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt index ef5328371122..56636f927203 100644 --- a/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt +++ b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt @@ -13,4 +13,4 @@ ab8500_chargalg { }; For information on battery specific node, Ref: -Documentation/devicetree/bindings/power_supply/ab8500/fg.txt +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt index 6bdbb08ea9e0..24ada03e07b4 100644 --- a/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt +++ b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt @@ -22,4 +22,4 @@ Required Properties: }; For information on battery specific node, Ref: -Documentation/devicetree/bindings/power_supply/ab8500/fg.txt +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt index 615c1cb6889f..37994fdb18ca 100644 --- a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -25,6 +25,7 @@ Required properties: * "ti,bq27545" - BQ27545 * "ti,bq27421" - BQ27421 * "ti,bq27425" - BQ27425 + * "ti,bq27426" - BQ27426 * "ti,bq27441" - BQ27441 * "ti,bq27621" - BQ27621 - reg: integer, I2C address of the fuel gauge. diff --git a/Documentation/devicetree/bindings/power/wakeup-source.txt b/Documentation/devicetree/bindings/power/wakeup-source.txt index 5d254ab13ebf..cfd74659fbed 100644 --- a/Documentation/devicetree/bindings/power/wakeup-source.txt +++ b/Documentation/devicetree/bindings/power/wakeup-source.txt @@ -22,7 +22,7 @@ List of legacy properties and respective binding document 3. "has-tpo" Documentation/devicetree/bindings/rtc/rtc-opal.txt 4. "linux,wakeup" Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt Documentation/devicetree/bindings/mfd/tc3589x.txt - Documentation/devicetree/bindings/input/ads7846.txt + Documentation/devicetree/bindings/input/touchscreen/ads7846.txt 5. "linux,keypad-wakeup" Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt 6. "linux,input-wakeup" Documentation/devicetree/bindings/input/samsung-keypad.txt 7. "nvidia,wakeup-source" Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt diff --git a/Documentation/devicetree/bindings/pps/pps-gpio.txt b/Documentation/devicetree/bindings/pps/pps-gpio.txt index 0de23b793657..3683874832ae 100644 --- a/Documentation/devicetree/bindings/pps/pps-gpio.txt +++ b/Documentation/devicetree/bindings/pps/pps-gpio.txt @@ -20,5 +20,4 @@ Example: assert-falling-edge; compatible = "pps-gpio"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt new file mode 100644 index 000000000000..0f569d8e73a3 --- /dev/null +++ b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt @@ -0,0 +1,69 @@ +* Freescale QorIQ 1588 timer based PTP clock + +General Properties: + + - compatible Should be "fsl,etsec-ptp" + - reg Offset and length of the register set for the device + - interrupts There should be at least two interrupts. Some devices + have as many as four PTP related interrupts. + +Clock Properties: + + - fsl,cksel Timer reference clock source. + - fsl,tclk-period Timer reference clock period in nanoseconds. + - fsl,tmr-prsc Prescaler, divides the output clock. + - fsl,tmr-add Frequency compensation value. + - fsl,tmr-fiper1 Fixed interval period pulse generator. + - fsl,tmr-fiper2 Fixed interval period pulse generator. + - fsl,max-adj Maximum frequency adjustment in parts per billion. + + These properties set the operational parameters for the PTP + clock. You must choose these carefully for the clock to work right. + Here is how to figure good values: + + TimerOsc = selected reference clock MHz + tclk_period = desired clock period nanoseconds + NominalFreq = 1000 / tclk_period MHz + FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0) + tmr_add = ceil(2^32 / FreqDivRatio) + OutputClock = NominalFreq / tmr_prsc MHz + PulseWidth = 1 / OutputClock microseconds + FiperFreq1 = desired frequency in Hz + FiperDiv1 = 1000000 * OutputClock / FiperFreq1 + tmr_fiper1 = tmr_prsc * tclk_period * FiperDiv1 - tclk_period + max_adj = 1000000000 * (FreqDivRatio - 1.0) - 1 + + The calculation for tmr_fiper2 is the same as for tmr_fiper1. The + driver expects that tmr_fiper1 will be correctly set to produce a 1 + Pulse Per Second (PPS) signal, since this will be offered to the PPS + subsystem to synchronize the Linux clock. + + Reference clock source is determined by the value, which is holded + in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the + value, which will be directly written in those bits, that is why, + according to reference manual, the next clock sources can be used: + + <0> - external high precision timer reference clock (TSEC_TMR_CLK + input is used for this purpose); + <1> - eTSEC system clock; + <2> - eTSEC1 transmit clock; + <3> - RTC clock input. + + When this attribute is not used, eTSEC system clock will serve as + IEEE 1588 timer reference clock. + +Example: + + ptp_clock@24e00 { + compatible = "fsl,etsec-ptp"; + reg = <0x24E00 0xB0>; + interrupts = <12 0x8 13 0x8>; + interrupt-parent = < &ipic >; + fsl,cksel = <1>; + fsl,tclk-period = <10>; + fsl,tmr-prsc = <100>; + fsl,tmr-add = <0x999999A4>; + fsl,tmr-fiper1 = <0x3B9AC9F6>; + fsl,tmr-fiper2 = <0x00018696>; + fsl,max-adj = <659999998>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt index 2e53324fb720..5ccfcc82da08 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt @@ -2,7 +2,7 @@ Required properties: - compatible: Shall contain "ti,omap-dmtimer-pwm". -- ti,timers: phandle to PWM capable OMAP timer. See arm/omap/timer.txt for info +- ti,timers: phandle to PWM capable OMAP timer. See timer/ti,timer.txt for info about these timers. - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index c6dd3f5e485b..f0ada3b14d70 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -21,7 +21,7 @@ Each regulator is defined using the standard binding for regulators. Example 1: PFUZE100 - pmic: pfuze100@8 { + pfuze100: pmic@8 { compatible = "fsl,pfuze100"; reg = <0x08>; @@ -122,7 +122,7 @@ Example 1: PFUZE100 Example 2: PFUZE200 - pmic: pfuze200@8 { + pfuze200: pmic@8 { compatible = "fsl,pfuze200"; reg = <0x08>; @@ -216,7 +216,7 @@ Example 2: PFUZE200 Example 3: PFUZE3000 - pmic: pfuze3000@8 { + pfuze3000: pmic@8 { compatible = "fsl,pfuze3000"; reg = <0x08>; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 57d2c65899df..406f2e570c50 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -110,6 +110,11 @@ Qualcomm SPMI Regulators Definition: Reference to regulator supplying the input pin, as described in the data sheet. +- qcom,saw-reg: + Usage: optional + Value type: <phandle> + Description: Reference to syscon node defining the SAW registers. + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each @@ -201,6 +206,17 @@ see regulator.txt - with additional custom properties described below: 2 = 0.55 uA 3 = 0.75 uA +- qcom,saw-slave: + Usage: optional + Value type: <boo> + Description: SAW controlled gang slave. Will not be configured. + +- qcom,saw-leader: + Usage: optional + Value type: <boo> + Description: SAW controlled gang leader. Will be configured as + SAW regulator. + Example: regulators { @@ -221,3 +237,32 @@ Example: .... }; + +Example 2: + + saw3: syscon@9A10000 { + compatible = "syscon"; + reg = <0x9A10000 0x1000>; + }; + + ... + + spm-regulators { + compatible = "qcom,pm8994-regulators"; + qcom,saw-reg = <&saw3>; + s8 { + qcom,saw-slave; + }; + s9 { + qcom,saw-slave; + }; + s10 { + qcom,saw-slave; + }; + pm8994_s11_saw: s11 { + qcom,saw-leader; + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1140000>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 2babe15b618d..a7cd36877bfe 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -59,6 +59,11 @@ Optional properties: - regulator-initial-mode: initial operating mode. The set of possible operating modes depends on the capabilities of every hardware so each device binding documentation explains which values the regulator supports. +- regulator-allowed-modes: list of operating modes that software is allowed to + configure for the regulator at run-time. Elements may be specified in any + order. The set of possible operating modes depends on the capabilities of + every hardware so each device binding document explains which values the + regulator supports. - regulator-system-load: Load in uA present on regulator that is not captured by any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. @@ -68,6 +73,11 @@ Optional properties: 0: Disable active discharge. 1: Enable active discharge. Absence of this property will leave configuration to default. +- regulator-coupled-with: Regulators with which the regulator + is coupled. The linkage is 2-way - all coupled regulators should be linked + with each other. A regulator should not be coupled with its supplier. +- regulator-coupled-max-spread: Max spread between voltages of coupled regulators + in microvolts. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt new file mode 100644 index 000000000000..4edf3137d9f7 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -0,0 +1,126 @@ +ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings + +BD71837MWV is a programmable Power Management +IC (PMIC) for powering single-core, dual-core, and +quad-core SoC’s such as NXP-i.MX 8M. It is optimized +for low BOM cost and compact solution footprint. It +integrates 8 Buck regulators and 7 LDO’s to provide all +the power rails required by the SoC and the commonly +used peripherals. + +Required properties: + - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" + +List of regulators provided by this controller. BD71837 regulators node +should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at +Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +Regulator nodes should be named to BUCK_<number> and LDO_<number>. The +definition for each of these nodes is defined using the standard +binding for regulators at +Documentation/devicetree/bindings/regulator/regulator.txt. +Note that if BD71837 starts at RUN state you probably want to use +regulator-boot-on at least for BUCK6 and BUCK7 so that those are not +disabled by driver at startup. LDO5 and LDO6 are supplied by those and +if they are disabled at startup the voltage monitoring for LDO5/LDO6 will +cause PMIC to reset. + +The valid names for regulator nodes are: +BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8 +LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: +regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-ramp-delay = <1250>; + }; + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + }; + buck4: BUCK4 { + regulator-name = "buck4"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + }; + buck5: BUCK5 { + regulator-name = "buck5"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + }; + buck6: BUCK6 { + regulator-name = "buck6"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + buck7: BUCK7 { + regulator-name = "buck7"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + }; + buck8: BUCK8 { + regulator-name = "buck8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + }; + + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + }; + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + ldo4: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + }; + ldo5: LDO5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + ldo6: LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + }; + ldo7_reg: LDO7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; +}; + + diff --git a/Documentation/devicetree/bindings/regulator/sy8106a-regulator.txt b/Documentation/devicetree/bindings/regulator/sy8106a-regulator.txt new file mode 100644 index 000000000000..39a8ca73f572 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/sy8106a-regulator.txt @@ -0,0 +1,23 @@ +SY8106A Voltage regulator + +Required properties: +- compatible: Must be "silergy,sy8106a" +- reg: I2C slave address - must be <0x65> +- silergy,fixed-microvolt - the voltage when I2C regulating is disabled (set + by external resistor like a fixed voltage) + +Any property defined as part of the core regulator binding, defined in +./regulator.txt, can also be used. + +Example: + + sy8106a { + compatible = "silergy,sy8106a"; + reg = <0x65>; + regulator-name = "sy8106a-vdd"; + silergy,fixed-microvolt = <1200000>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 00d3d58a102f..d90182425450 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -11,6 +11,7 @@ on the Qualcomm Hexagon core. "qcom,msm8916-mss-pil", "qcom,msm8974-mss-pil" "qcom,msm8996-mss-pil" + "qcom,sdm845-mss-pil" - reg: Usage: required diff --git a/Documentation/devicetree/bindings/reserved-memory/qcom,cmd-db.txt b/Documentation/devicetree/bindings/reserved-memory/qcom,cmd-db.txt new file mode 100644 index 000000000000..68395530c0a5 --- /dev/null +++ b/Documentation/devicetree/bindings/reserved-memory/qcom,cmd-db.txt @@ -0,0 +1,37 @@ +Command DB +--------- + +Command DB is a database that provides a mapping between resource key and the +resource address for a system resource managed by a remote processor. The data +is stored in a shared memory region and is loaded by the remote processor. + +Some of the Qualcomm Technologies Inc SoC's have hardware accelerators for +controlling shared resources. Depending on the board configuration the shared +resource properties may change. These properties are dynamically probed by the +remote processor and made available in the shared memory. + +The bindings for Command DB is specified in the reserved-memory section in +devicetree. The devicetree representation of the command DB driver should be: + +Properties: +- compatible: + Usage: required + Value type: <string> + Definition: Should be "qcom,cmd-db" + +- reg: + Usage: required + Value type: <prop encoded array> + Definition: The register address that points to the actual location of + the Command DB in memory. + +Example: + + reserved-memory { + [...] + reserved-memory@85fe0000 { + reg = <0x0 0x85fe0000 0x0 0x20000>; + compatible = "qcom,cmd-db"; + no-map; + }; + }; diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt index 294a0dae106a..67e83b02e10b 100644 --- a/Documentation/devicetree/bindings/reset/renesas,rst.txt +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -17,6 +17,7 @@ Required properties: Examples with soctypes are: - "renesas,r8a7743-rst" (RZ/G1M) - "renesas,r8a7745-rst" (RZ/G1E) + - "renesas,r8a77470-rst" (RZ/G1C) - "renesas,r8a7778-reset-wdt" (R-Car M1A) - "renesas,r8a7779-reset-wdt" (R-Car H1) - "renesas,r8a7790-rst" (R-Car H2) @@ -29,6 +30,7 @@ Required properties: - "renesas,r8a77965-rst" (R-Car M3-N) - "renesas,r8a77970-rst" (R-Car V3M) - "renesas,r8a77980-rst" (R-Car V3H) + - "renesas,r8a77990-rst" (R-Car E3) - "renesas,r8a77995-rst" (R-Car D3) - reg: Address start and address range for the device. diff --git a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt index 627b29531a32..aaac7975f61c 100644 --- a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt @@ -14,11 +14,16 @@ Optional properties: - clocks : phandle to clock-controller plus clock-specifier pair - clock-names : "ipsec" as a clock name +Optional properties: + +- interrupts: specify the interrupt for the RNG block + Example: rng { - compatible = "brcm,bcm2835-rng"; - reg = <0x7e104000 0x10>; + compatible = "brcm,bcm2835-rng"; + reg = <0x7e104000 0x10>; + interrupts = <2 29>; }; rng@18033000 { diff --git a/Documentation/devicetree/bindings/crypto/samsung,exynos-rng4.txt b/Documentation/devicetree/bindings/rng/samsung,exynos4-rng.txt index a13fbdb4bd88..a13fbdb4bd88 100644 --- a/Documentation/devicetree/bindings/crypto/samsung,exynos-rng4.txt +++ b/Documentation/devicetree/bindings/rng/samsung,exynos4-rng.txt diff --git a/Documentation/devicetree/bindings/sparc_sun_oracle_rng.txt b/Documentation/devicetree/bindings/rng/sparc_sun_oracle_rng.txt index b0b211194c71..b0b211194c71 100644 --- a/Documentation/devicetree/bindings/sparc_sun_oracle_rng.txt +++ b/Documentation/devicetree/bindings/rng/sparc_sun_oracle_rng.txt diff --git a/Documentation/devicetree/bindings/rtc/nxp,rtc-2123.txt b/Documentation/devicetree/bindings/rtc/nxp,rtc-2123.txt index 5cbc0b145a61..811124a36d16 100644 --- a/Documentation/devicetree/bindings/rtc/nxp,rtc-2123.txt +++ b/Documentation/devicetree/bindings/rtc/nxp,rtc-2123.txt @@ -9,7 +9,7 @@ Optional properties: Example: -rtc: nxp,rtc-pcf2123@3 { +pcf2123: rtc@3 { compatible = "nxp,rtc-pcf2123" reg = <3> spi-cs-high; diff --git a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt index a66692a08ace..c920e2736991 100644 --- a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt @@ -1,23 +1,29 @@ STM32 Real Time Clock Required properties: -- compatible: can be either "st,stm32-rtc" or "st,stm32h7-rtc", depending on - the device is compatible with stm32(f4/f7) or stm32h7. +- compatible: can be one of the following: + - "st,stm32-rtc" for devices compatible with stm32(f4/f7). + - "st,stm32h7-rtc" for devices compatible with stm32h7. + - "st,stm32mp1-rtc" for devices compatible with stm32mp1. - reg: address range of rtc register set. - clocks: can use up to two clocks, depending on part used: - "rtc_ck": RTC clock source. - It is required on stm32(f4/f7) and stm32h7. - "pclk": RTC APB interface clock. It is not present on stm32(f4/f7). - It is required on stm32h7. + It is required on stm32(h7/mp1). - clock-names: must be "rtc_ck" and "pclk". - It is required only on stm32h7. + It is required on stm32(h7/mp1). - interrupt-parent: phandle for the interrupt controller. -- interrupts: rtc alarm interrupt. -- st,syscfg: phandle for pwrcfg, mandatory to disable/enable backup domain - (RTC registers) write protection. + It is required on stm32(f4/f7/h7). +- interrupts: rtc alarm interrupt. On stm32mp1, a second interrupt is required + for rtc alarm wakeup interrupt. +- st,syscfg: phandle/offset/mask triplet. The phandle to pwrcfg used to + access control register at offset, and change the dbp (Disable Backup + Protection) bit represented by the mask, mandatory to disable/enable backup + domain (RTC registers) write protection. + It is required on stm32(f4/f7/h7). -Optional properties (to override default rtc_ck parent clock): +Optional properties (to override default rtc_ck parent clock on stm32(f4/f7/h7): - assigned-clocks: reference to the rtc_ck clock entry. - assigned-clock-parents: phandle of the new parent clock of rtc_ck. @@ -31,7 +37,7 @@ Example: assigned-clock-parents = <&rcc 1 CLK_LSE>; interrupt-parent = <&exti>; interrupts = <17 1>; - st,syscfg = <&pwrcfg>; + st,syscfg = <&pwrcfg 0x00 0x100>; }; rtc: rtc@58004000 { @@ -44,5 +50,14 @@ Example: interrupt-parent = <&exti>; interrupts = <17 1>; interrupt-names = "alarm"; - st,syscfg = <&pwrcfg>; + st,syscfg = <&pwrcfg 0x00 0x100>; + }; + + rtc: rtc@5c004000 { + compatible = "st,stm32mp1-rtc"; + reg = <0x5c004000 0x400>; + clocks = <&rcc RTCAPB>, <&rcc RTC>; + clock-names = "pclk", "rtc_ck"; + interrupts-extended = <&intc GIC_SPI 3 IRQ_TYPE_NONE>, + <&exti 19 1>; }; diff --git a/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt index 7a34345d0ca3..c8dd440e9747 100644 --- a/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt +++ b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt @@ -8,7 +8,7 @@ Required properties: See: Documentation/devicetree/bindings/clock/clock-bindings.txt - pinctrl-names: A pinctrl state names "default" must be defined. - pinctrl-0: Phandle referencing pin configuration of the UART peripheral. - See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt Optional properties: - cts-gpios: CTS pin for UART diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt new file mode 100644 index 000000000000..bcc612cc7423 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt @@ -0,0 +1,84 @@ +Qualcomm APR (Asynchronous Packet Router) binding + +This binding describes the Qualcomm APR. APR is a IPC protocol for +communication between Application processor and QDSP. APR is mainly +used for audio/voice services on the QDSP. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" + +- reg + Usage: required + Value type: <u32> + Definition: Destination processor ID. + Possible values are : + 1 - APR simulator + 2 - PC + 3 - MODEM + 4 - ADSP + 5 - APPS + 6 - MODEM2 + 7 - APPS2 + += APR SERVICES +Each subnode of the APR node represents service tied to this apr. The name +of the nodes are not important. The properties of these nodes are defined +by the individual bindings for the specific service +- All APR services MUST contain the following property: + +- reg + Usage: required + Value type: <u32> + Definition: APR Service ID + Possible values are : + 3 - DSP Core Service + 4 - Audio Front End Service. + 5 - Voice Stream Manager Service. + 6 - Voice processing manager. + 7 - Audio Stream Manager Service. + 8 - Audio Device Manager Service. + 9 - Multimode voice manager. + 10 - Core voice stream. + 11 - Core voice processor. + 12 - Ultrasound stream manager. + 13 - Listen stream manager. + += EXAMPLE +The following example represents a QDSP based sound card on a MSM8996 device +which uses apr as communication between Apps and QDSP. + + apr@4 { + compatible = "qcom,apr-v2"; + reg = <APR_DOMAIN_ADSP>; + + q6core@3 { + compatible = "qcom,q6core"; + reg = <APR_SVC_ADSP_CORE>; + }; + + q6afe@4 { + compatible = "qcom,q6afe"; + reg = <APR_SVC_AFE>; + + dais { + #sound-dai-cells = <1>; + hdmi@1 { + reg = <1>; + }; + }; + }; + + q6asm@7 { + compatible = "qcom,q6asm"; + reg = <APR_SVC_ASM>; + ... + }; + + q6adm@8 { + compatible = "qcom,q6adm"; + reg = <APR_SVC_ADM>; + ... + }; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt new file mode 100644 index 000000000000..d330c73de9a2 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt @@ -0,0 +1,119 @@ +Qualcomm Technologies, Inc. GENI Serial Engine QUP Wrapper Controller + +Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper +is a programmable module for supporting a wide range of serial interfaces +like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial +Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP +Wrapper controller is modeled as a node with zero or more child nodes each +representing a serial engine. + +Required properties: +- compatible: Must be "qcom,geni-se-qup". +- reg: Must contain QUP register address and length. +- clock-names: Must contain "m-ahb" and "s-ahb". +- clocks: AHB clocks needed by the device. + +Required properties if child node exists: +- #address-cells: Must be <1> for Serial Engine Address +- #size-cells: Must be <1> for Serial Engine Address Size +- ranges: Must be present + +Properties for children: + +A GENI based QUP wrapper controller node can contain 0 or more child nodes +representing serial devices. These serial devices can be a QCOM UART, I2C +controller, SPI controller, or some combination of aforementioned devices. +Please refer below the child node definitions for the supported serial +interface protocols. + +Qualcomm Technologies Inc. GENI Serial Engine based I2C Controller + +Required properties: +- compatible: Must be "qcom,geni-i2c". +- reg: Must contain QUP register address and length. +- interrupts: Must contain I2C interrupt. +- clock-names: Must contain "se". +- clocks: Serial engine core clock needed by the device. +- #address-cells: Must be <1> for I2C device address. +- #size-cells: Must be <0> as I2C addresses have no size component. + +Optional property: +- clock-frequency: Desired I2C bus clock frequency in Hz. + When missing default to 400000Hz. + +Child nodes should conform to I2C bus binding as described in i2c.txt. + +Qualcomm Technologies Inc. GENI Serial Engine based UART Controller + +Required properties: +- compatible: Must be "qcom,geni-debug-uart". +- reg: Must contain UART register location and length. +- interrupts: Must contain UART core interrupts. +- clock-names: Must contain "se". +- clocks: Serial engine core clock needed by the device. + +Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller + +Required properties: +- compatible: Must contain "qcom,geni-spi". +- reg: Must contain SPI register location and length. +- interrupts: Must contain SPI controller interrupts. +- clock-names: Must contain "se". +- clocks: Serial engine core clock needed by the device. +- spi-max-frequency: Specifies maximum SPI clock frequency, units - Hz. +- #address-cells: Must be <1> to define a chip select address on + the SPI bus. +- #size-cells: Must be <0>. + +SPI slave nodes must be children of the SPI master node and conform to SPI bus +binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + geniqup@8c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x8c0000 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, + <&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + i2c0: i2c@a94000 { + compatible = "qcom,geni-i2c"; + reg = <0xa94000 0x4000>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "se"; + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S5_CLK>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qup_1_i2c_5_active>; + pinctrl-1 = <&qup_1_i2c_5_sleep>; + #address-cells = <1>; + #size-cells = <0>; + }; + + uart0: serial@a88000 { + compatible = "qcom,geni-debug-uart"; + reg = <0xa88000 0x7000>; + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "se"; + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qup_1_uart_3_active>; + pinctrl-1 = <&qup_1_uart_3_sleep>; + }; + + spi0: spi@a84000 { + compatible = "qcom,geni-spi"; + reg = <0xa84000 0x4000>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "se"; + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qup_1_spi_2_active>; + pinctrl-1 = <&qup_1_spi_2_sleep>; + spi-max-frequency = <19200000>; + #address-cells = <1>; + #size-cells = <0>; + }; + } diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt index a48049ccf6d0..89e1cb9212f6 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt @@ -22,6 +22,7 @@ resources. "qcom,rpm-apq8084" "qcom,rpm-msm8916" "qcom,rpm-msm8974" + "qcom,rpm-msm8998" - qcom,smd-channels: Usage: required diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt index ea1dc75ec9ea..234ae2256501 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt @@ -22,9 +22,15 @@ The edge is described by the following properties: Definition: should specify the IRQ used by the remote processor to signal this processor about communication related updates -- qcom,ipc: +- mboxes: Usage: required Value type: <prop-encoded-array> + Definition: reference to the associated doorbell in APCS, as described + in mailbox/mailbox.txt + +- qcom,ipc: + Usage: required, unless mboxes is specified + Value type: <prop-encoded-array> Definition: three entries specifying the outgoing ipc bit used for signaling the remote processor: - phandle to a syscon node representing the apcs registers diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt index 301d2a9bc1b8..5d49d0a2ff29 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -5,6 +5,10 @@ powered up/down by software based on different application scenes to save power. Required properties for power domain controller: - compatible: Should be one of the following. + "rockchip,px30-power-controller" - for PX30 SoCs. + "rockchip,rk3036-power-controller" - for RK3036 SoCs. + "rockchip,rk3128-power-controller" - for RK3128 SoCs. + "rockchip,rk3228-power-controller" - for RK3228 SoCs. "rockchip,rk3288-power-controller" - for RK3288 SoCs. "rockchip,rk3328-power-controller" - for RK3328 SoCs. "rockchip,rk3366-power-controller" - for RK3366 SoCs. @@ -17,6 +21,10 @@ Required properties for power domain controller: Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: + "include/dt-bindings/power/px30-power.h" - for PX30 type power domain. + "include/dt-bindings/power/rk3036-power.h" - for RK3036 type power domain. + "include/dt-bindings/power/rk3128-power.h" - for RK3128 type power domain. + "include/dt-bindings/power/rk3228-power.h" - for RK3228 type power domain. "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for RK3328 type power domain. "include/dt-bindings/power/rk3366-power.h" - for RK3366 type power domain. @@ -93,6 +101,10 @@ Node of a device using power domains must have a power-domains property, containing a phandle to the power device node and an index specifying which power domain to use. The index should use macros in: + "include/dt-bindings/power/px30-power.h" - for px30 type power domain. + "include/dt-bindings/power/rk3036-power.h" - for rk3036 type power domain. + "include/dt-bindings/power/rk3128-power.h" - for rk3128 type power domain. + "include/dt-bindings/power/rk3128-power.h" - for rk3228 type power domain. "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for rk3328 type power domain. "include/dt-bindings/power/rk3366-power.h" - for rk3366 type power domain. diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt index 77cd42cc5f54..b025770eeb92 100644 --- a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt @@ -17,7 +17,8 @@ pool management. Required properties: -- compatible : Must be "ti,keystone-navigator-qmss"; +- compatible : Must be "ti,keystone-navigator-qmss". + : Must be "ti,66ak2g-navss-qm" for QMSS on K2G SoC. - clocks : phandle to the reference clock for this device. - queue-range : <start number> total range of queue numbers for the device. - linkram0 : <address size> for internal link ram, where size is the total @@ -39,6 +40,12 @@ Required properties: - Descriptor memory setup region. - Queue Management/Queue Proxy region for queue Push. - Queue Management/Queue Proxy region for queue Pop. + +For QMSS on K2G SoC, following QM reg indexes are used in that order + - Queue Peek region. + - Queue configuration region. + - Queue Management/Queue Proxy region for queue Push/Pop. + - queue-pools : child node classifying the queue ranges into pools. Queue ranges are grouped into 3 type of pools: - qpend : pool of qpend(interruptible) queues diff --git a/Documentation/devicetree/bindings/sound/adi,ssm2305.txt b/Documentation/devicetree/bindings/sound/adi,ssm2305.txt new file mode 100644 index 000000000000..a9c9d83c8a30 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,ssm2305.txt @@ -0,0 +1,14 @@ +Analog Devices SSM2305 Speaker Amplifier +======================================== + +Required properties: + - compatible : "adi,ssm2305" + - shutdown-gpios : The gpio connected to the shutdown pin. + The gpio signal is ACTIVE_LOW. + +Example: + +ssm2305: analog-amplifier { + compatible = "adi,ssm2305"; + shutdown-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/sound/atmel-i2s.txt b/Documentation/devicetree/bindings/sound/atmel-i2s.txt new file mode 100644 index 000000000000..735368b8a73f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel-i2s.txt @@ -0,0 +1,47 @@ +* Atmel I2S controller + +Required properties: +- compatible: Should be "atmel,sama5d2-i2s". +- reg: Should be the physical base address of the controller and the + length of memory mapped region. +- interrupts: Should contain the interrupt for the controller. +- dmas: Should be one per channel name listed in the dma-names property, + as described in atmel-dma.txt and dma.txt files. +- dma-names: Two dmas have to be defined, "tx" and "rx". + This IP also supports one shared channel for both rx and tx; + if this mode is used, one "rx-tx" name must be used. +- clocks: Must contain an entry for each entry in clock-names. + Please refer to clock-bindings.txt. +- clock-names: Should be one of each entry matching the clocks phandles list: + - "pclk" (peripheral clock) Required. + - "gclk" (generated clock) Optional (1). + - "aclk" (Audio PLL clock) Optional (1). + - "muxclk" (I2S mux clock) Optional (1). + +Optional properties: +- pinctrl-0: Should specify pin control groups used for this controller. +- princtrl-names: Should contain only one value - "default". + + +(1) : Only the peripheral clock is required. The generated clock, the Audio + PLL clock adn the I2S mux clock are optional and should only be set + together, when Master Mode is required. + +Example: + + i2s@f8050000 { + compatible = "atmel,sama5d2-i2s"; + reg = <0xf8050000 0x300>; + interrupts = <54 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(31))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(32))>; + dma-names = "tx", "rx"; + clocks = <&i2s0_clk>, <&i2s0_gclk>, <&audio_pll_pmc>, <&i2s0muxck>; + clock-names = "pclk", "gclk", "aclk", "muxclk"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2s0_default>; + }; diff --git a/Documentation/devicetree/bindings/sound/cs42xx8.txt b/Documentation/devicetree/bindings/sound/cs42xx8.txt index f631fbca6284..8619a156d038 100644 --- a/Documentation/devicetree/bindings/sound/cs42xx8.txt +++ b/Documentation/devicetree/bindings/sound/cs42xx8.txt @@ -16,7 +16,7 @@ Required properties: Example: -codec: cs42888@48 { +cs42888: codec@48 { compatible = "cirrus,cs42888"; reg = <0x48>; clocks = <&codec_mclk 0>; diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt index f5a14115b459..1d4d9f938689 100644 --- a/Documentation/devicetree/bindings/sound/fsl,asrc.txt +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -31,14 +31,16 @@ Required properties: it. This property is optional depending on the SoC design. - - big-endian : If this property is absent, the little endian mode - will be in use as default. Otherwise, the big endian - mode will be in use for all the device registers. - - fsl,asrc-rate : Defines a mutual sample rate used by DPCM Back Ends. - fsl,asrc-width : Defines a mutual sample width used by DPCM Back Ends. +Optional properties: + + - big-endian : If this property is absent, the little endian mode + will be in use as default. Otherwise, the big endian + mode will be in use for all the device registers. + Example: asrc: asrc@2034000 { diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index cacd18bb9ba6..5b9914367610 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -42,6 +42,8 @@ Required properties: means all the settings for Receiving would be duplicated from Transmition related registers. +Optional properties: + - big-endian : If this property is absent, the native endian mode will be in use as default, or the big endian mode will be in use for all the device registers. diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt index 38cfa7573441..8b324f82a782 100644 --- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt +++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt @@ -33,6 +33,8 @@ Required properties: it. This property is optional depending on the SoC design. +Optional properties: + - big-endian : If this property is absent, the native endian mode will be in use as default, or the big endian mode will be in use for all the device registers. diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 740b467adf7d..dd9e59738e08 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -28,9 +28,6 @@ Required properties: pinctrl-names. See ../pinctrl/pinctrl-bindings.txt for details of the property values. - - big-endian : Boolean property, required if all the FTM_PWM - registers are big-endian rather than little-endian. - - lsb-first : Configures whether the LSB or the MSB is transmitted first for the fifo data. If this property is absent, the MSB is transmitted first as default, or the LSB @@ -48,6 +45,11 @@ Required properties: receive data by following their own bit clocks and frame sync clocks separately. +Optional properties: + + - big-endian : Boolean property, required if all the SAI + registers are big-endian rather than little-endian. + Optional properties (for mx6ul): - fsl,sai-mclk-direction-output: This is a boolean property. If present, diff --git a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt index e2f7f4951215..560762e0a168 100644 --- a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt +++ b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt @@ -1,7 +1,9 @@ Mediatek AFE PCM controller for mt2701 Required properties: -- compatible = "mediatek,mt2701-audio"; +- compatible: should be one of the followings. + - "mediatek,mt2701-audio" + - "mediatek,mt7622-audio" - interrupts: should contain AFE and ASYS interrupts - interrupt-names: should be "afe" and "asys" - power-domains: should define the power domain diff --git a/Documentation/devicetree/bindings/sound/mt6351.txt b/Documentation/devicetree/bindings/sound/mt6351.txt new file mode 100644 index 000000000000..7fb2cb99245e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt6351.txt @@ -0,0 +1,16 @@ +Mediatek MT6351 Audio Codec + +The communication between MT6351 and SoC is through Mediatek PMIC wrapper. +For more detail, please visit Mediatek PMIC wrapper documentation. + +Must be a child node of PMIC wrapper. + +Required properties: + +- compatible : "mediatek,mt6351-sound". + +Example: + +mt6351_snd { + compatible = "mediatek,mt6351-sound"; +}; diff --git a/Documentation/devicetree/bindings/sound/mt6797-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt6797-afe-pcm.txt new file mode 100644 index 000000000000..0ae29de15bfd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt6797-afe-pcm.txt @@ -0,0 +1,42 @@ +Mediatek AFE PCM controller for mt6797 + +Required properties: +- compatible = "mediatek,mt6797-audio"; +- reg: register location and size +- interrupts: should contain AFE interrupt +- power-domains: should define the power domain +- clocks: Must contain an entry for each entry in clock-names +- clock-names: should have these clock names: + "infra_sys_audio_clk", + "infra_sys_audio_26m", + "mtkaif_26m_clk", + "top_mux_audio", + "top_mux_aud_intbus", + "top_sys_pll3_d4", + "top_sys_pll1_d4", + "top_clk26m_clk"; + +Example: + + afe: mt6797-afe-pcm@11220000 { + compatible = "mediatek,mt6797-audio"; + reg = <0 0x11220000 0 0x1000>; + interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT6797_POWER_DOMAIN_AUDIO>; + clocks = <&infrasys CLK_INFRA_AUDIO>, + <&infrasys CLK_INFRA_AUDIO_26M>, + <&infrasys CLK_INFRA_AUDIO_26M_PAD_TOP>, + <&topckgen CLK_TOP_MUX_AUDIO>, + <&topckgen CLK_TOP_MUX_AUD_INTBUS>, + <&topckgen CLK_TOP_SYSPLL3_D4>, + <&topckgen CLK_TOP_SYSPLL1_D4>, + <&clk26m>; + clock-names = "infra_sys_audio_clk", + "infra_sys_audio_26m", + "mtkaif_26m_clk", + "top_mux_audio", + "top_mux_aud_intbus", + "top_sys_pll3_d4", + "top_sys_pll1_d4", + "top_clk26m_clk"; + }; diff --git a/Documentation/devicetree/bindings/sound/mt6797-mt6351.txt b/Documentation/devicetree/bindings/sound/mt6797-mt6351.txt new file mode 100644 index 000000000000..1d95a8840f19 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt6797-mt6351.txt @@ -0,0 +1,14 @@ +MT6797 with MT6351 CODEC + +Required properties: +- compatible: "mediatek,mt6797-mt6351-sound" +- mediatek,platform: the phandle of MT6797 ASoC platform +- mediatek,audio-codec: the phandles of MT6351 codec + +Example: + + sound { + compatible = "mediatek,mt6797-mt6351-sound"; + mediatek,audio-codec = <&mt6351_snd>; + mediatek,platform = <&afe>; + }; diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8096.txt b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt new file mode 100644 index 000000000000..aa54e49fc8a2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt @@ -0,0 +1,109 @@ +* Qualcomm Technologies APQ8096 ASoC sound card driver + +This binding describes the APQ8096 sound card, which uses qdsp for audio. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,apq8096-sndcard" + +- qcom,audio-routing: + Usage: Optional + Value type: <stringlist> + Definition: A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, MicBias + of codec and the jacks on the board: + Valid names include: + + Board Connectors: + "Headphone Left" + "Headphone Right" + "Earphone" + "Line Out1" + "Line Out2" + "Line Out3" + "Line Out4" + "Analog Mic1" + "Analog Mic2" + "Analog Mic3" + "Analog Mic4" + "Analog Mic5" + "Analog Mic6" + "Digital Mic2" + "Digital Mic3" + + Audio pins and MicBias on WCD9335 Codec: + "MIC_BIAS1 + "MIC_BIAS2" + "MIC_BIAS3" + "MIC_BIAS4" + "AMIC1" + "AMIC2" + "AMIC3" + "AMIC4" + "AMIC5" + "AMIC6" + "AMIC6" + "DMIC1" + "DMIC2" + "DMIC3" += dailinks +Each subnode of sndcard represents either a dailink, and subnodes of each +dailinks would be cpu/codec/platform dais. + +- link-name: + Usage: required + Value type: <string> + Definition: User friendly name for dai link + += CPU, PLATFORM, CODEC dais subnodes +- cpu: + Usage: required + Value type: <subnode> + Definition: cpu dai sub-node + +- codec: + Usage: Optional + Value type: <subnode> + Definition: codec dai sub-node + +- platform: + Usage: Optional + Value type: <subnode> + Definition: platform dai sub-node + +- sound-dai: + Usage: required + Value type: <phandle with arguments> + Definition: dai phandle/s and port of CPU/CODEC/PLATFORM node. + +Example: + +audio { + compatible = "qcom,apq8096-sndcard"; + qcom,model = "DB820c"; + + mm1-dai-link { + link-name = "MultiMedia1"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; + }; + }; + + hdmi-dai-link { + link-name = "HDMI Playback"; + cpu { + sound-dai = <&q6afe HDMI_RX>; + }; + + platform { + sound-dai = <&q6adm>; + }; + + codec { + sound-dai = <&hdmi 0>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6adm.txt b/Documentation/devicetree/bindings/sound/qcom,q6adm.txt new file mode 100644 index 000000000000..cb709e5dbc44 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,q6adm.txt @@ -0,0 +1,33 @@ +Qualcomm Audio Device Manager (Q6ADM) binding + +Q6ADM is one of the APR audio service on Q6DSP. +Please refer to qcom,apr.txt for details of the coommon apr service bindings +used by the apr service device. + +- but must contain the following property: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6adm-v<MAJOR-NUMBER>.<MINOR-NUMBER>". + Or "qcom,q6adm" where the version number can be queried + from DSP. + example "qcom,q6adm-v2.0" + + += ADM routing +"routing" subnode of the ADM node represents adm routing specific configuration + +- #sound-dai-cells + Usage: required + Value type: <u32> + Definition: Must be 0 + += EXAMPLE +q6adm@8 { + compatible = "qcom,q6adm"; + reg = <APR_SVC_ADM>; + q6routing: routing { + #sound-dai-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt new file mode 100644 index 000000000000..bdbf87df8c0b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt @@ -0,0 +1,172 @@ +Qualcomm Audio Front End (Q6AFE) binding + +AFE is one of the APR audio service on Q6DSP +Please refer to qcom,apr.txt for details of the common apr service bindings +used by all apr services. Must contain the following properties. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6afe-v<MAJOR-NUMBER>.<MINOR-NUMBER>" + Or "qcom,q6afe" where the version number can be queried + from DSP. + example "qcom,q6afe" + += AFE DAIs (Digial Audio Interface) +"dais" subnode of the AFE node. It represents afe dais, each afe dai is a +subnode of "dais" representing board specific dai setup. +"dais" node should have following properties followed by dai children. + +- #sound-dai-cells + Usage: required + Value type: <u32> + Definition: Must be 1 + +- #address-cells + Usage: required + Value type: <u32> + Definition: Must be 1 + +- #size-cells + Usage: required + Value type: <u32> + Definition: Must be 0 + +== AFE DAI is subnode of "dais" and represent a dai, it includes board specific +configuration of each dai. Must contain the following properties. + +- reg + Usage: required + Value type: <u32> + Definition: Must be dai id + +- qcom,sd-lines + Usage: required for mi2s interface + Value type: <prop-encoded-array> + Definition: Must be list of serial data lines used by this dai. + should be one or more of the 1-4 sd lines. + + - qcom,tdm-sync-mode: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Synchronization mode. + 0 - Short sync bit mode + 1 - Long sync mode + 2 - Short sync slot mode + + - qcom,tdm-sync-src: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Synchronization source. + 0 - External source + 1 - Internal source + + - qcom,tdm-data-out: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Data out signal to drive with other masters. + 0 - Disable + 1 - Enable + + - qcom,tdm-invert-sync: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Invert the sync. + 0 - Normal + 1 - Invert + + - qcom,tdm-data-delay: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Number of bit clock to delay data + with respect to sync edge. + 0 - 0 bit clock cycle + 1 - 1 bit clock cycle + 2 - 2 bit clock cycle + + - qcom,tdm-data-align: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Indicate how data is packed + within the slot. For example, 32 slot width in case of + sample bit width is 24. + 0 - MSB + 1 - LSB + += EXAMPLE + +q6afe@4 { + compatible = "qcom,q6afe"; + reg = <APR_SVC_AFE>; + + dais { + #sound-dai-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + hdmi@1 { + reg = <1>; + }; + + tdm@24 { + reg = <24>; + qcom,tdm-sync-mode = <1>: + qcom,tdm-sync-src = <1>; + qcom,tdm-data-out = <0>; + qcom,tdm-invert-sync = <1>; + qcom,tdm-data-delay = <1>; + qcom,tdm-data-align = <0>; + + }; + + tdm@25 { + reg = <25>; + qcom,tdm-sync-mode = <1>: + qcom,tdm-sync-src = <1>; + qcom,tdm-data-out = <0>; + qcom,tdm-invert-sync = <1>; + qcom,tdm-data-delay <1>: + qcom,tdm-data-align = <0>; + }; + + prim-mi2s-rx@16 { + reg = <16>; + qcom,sd-lines = <1 3>; + }; + + prim-mi2s-tx@17 { + reg = <17>; + qcom,sd-lines = <2>; + }; + + sec-mi2s-rx@18 { + reg = <18>; + qcom,sd-lines = <1 4>; + }; + + sec-mi2s-tx@19 { + reg = <19>; + qcom,sd-lines = <2>; + }; + + tert-mi2s-rx@20 { + reg = <20>; + qcom,sd-lines = <2 4>; + }; + + tert-mi2s-tx@21 { + reg = <21>; + qcom,sd-lines = <1>; + }; + + quat-mi2s-rx@22 { + reg = <22>; + qcom,sd-lines = <1>; + }; + + quat-mi2s-tx@23 { + reg = <23>; + qcom,sd-lines = <2>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6asm.txt b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt new file mode 100644 index 000000000000..2178eb91146f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt @@ -0,0 +1,33 @@ +Qualcomm Audio Stream Manager (Q6ASM) binding + +Q6ASM is one of the APR audio service on Q6DSP. +Please refer to qcom,apr.txt for details of the common apr service bindings +used by the apr service device. + +- but must contain the following property: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6asm-v<MAJOR-NUMBER>.<MINOR-NUMBER>". + Or "qcom,q6asm" where the version number can be queried + from DSP. + example "qcom,q6asm-v2.0" + += ASM DAIs (Digial Audio Interface) +"dais" subnode of the ASM node represents dai specific configuration + +- #sound-dai-cells + Usage: required + Value type: <u32> + Definition: Must be 1 + += EXAMPLE + +q6asm@7 { + compatible = "qcom,q6asm"; + reg = <APR_SVC_ASM>; + q6asmdai: dais { + #sound-dai-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6core.txt b/Documentation/devicetree/bindings/sound/qcom,q6core.txt new file mode 100644 index 000000000000..7f36ff8bec18 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,q6core.txt @@ -0,0 +1,21 @@ +Qualcomm ADSP Core service binding + +Q6CORE is one of the APR audio service on Q6DSP. +Please refer to qcom,apr.txt for details of the common apr service bindings +used by the apr service device. + +- but must contain the following property: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6core-v<MAJOR-NUMBER>.<MINOR-NUMBER>". + Or "qcom,q6core" where the version number can be queried + from DSP. + example "qcom,q6core-v2.0" + += EXAMPLE +q6core@3 { + compatible = "qcom,q6core"; + reg = <APR_SVC_ADSP_CORE>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt274.txt b/Documentation/devicetree/bindings/sound/rt274.txt index e9a6178c78cf..791a1bd767b9 100644 --- a/Documentation/devicetree/bindings/sound/rt274.txt +++ b/Documentation/devicetree/bindings/sound/rt274.txt @@ -26,7 +26,7 @@ Pins on the device (for linking into audio routes) for RT274: Example: -codec: rt274@1c { +rt274: codec@1c { compatible = "realtek,rt274"; reg = <0x1c>; interrupts = <7 IRQ_TYPE_EDGE_FALLING>; diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt index 4f33b0d96afe..b25ed08c7a5a 100644 --- a/Documentation/devicetree/bindings/sound/rt5514.txt +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -32,7 +32,7 @@ Pins on the device (for linking into audio routes) for I2C: Example: -codec: rt5514@57 { +rt5514: codec@57 { compatible = "realtek,rt5514"; reg = <0x57>; }; diff --git a/Documentation/devicetree/bindings/sound/rt5616.txt b/Documentation/devicetree/bindings/sound/rt5616.txt index e41085818559..540a4bf252e4 100644 --- a/Documentation/devicetree/bindings/sound/rt5616.txt +++ b/Documentation/devicetree/bindings/sound/rt5616.txt @@ -26,7 +26,7 @@ Pins on the device (for linking into audio routes) for RT5616: Example: -codec: rt5616@1b { +rt5616: codec@1b { compatible = "realtek,rt5616"; reg = <0x1b>; }; diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt index 57fe64643050..e40e4893eed8 100644 --- a/Documentation/devicetree/bindings/sound/rt5640.txt +++ b/Documentation/devicetree/bindings/sound/rt5640.txt @@ -22,6 +22,41 @@ Optional properties: - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using IN1P pin as dmic1 data pin + 2: using GPIO3 pin as dmic1 data pin + +- realtek,dmic2-data-pin + 0: dmic2 is not used + 1: using IN1N pin as dmic2 data pin + 2: using GPIO4 pin as dmic2 data pin + +- realtek,jack-detect-source + u32. Valid values: + 0: jack-detect is not used + 1: Use GPIO1 for jack-detect + 2: Use JD1_IN4P for jack-detect + 3: Use JD2_IN4N for jack-detect + 4: Use GPIO2 for jack-detect + 5: Use GPIO3 for jack-detect + 6: Use GPIO4 for jack-detect + +- realtek,jack-detect-not-inverted + bool. Normal jack-detect switches give an inverted signal, set this bool + in the rare case you've a jack-detect switch which is not inverted. + +- realtek,over-current-threshold-microamp + u32, micbias over-current detection threshold in µA, valid values are + 600, 1500 and 2000µA. + +- realtek,over-current-scale-factor + u32, micbias over-current detection scale-factor, valid values are: + 0: Scale current by 0.5 + 1: Scale current by 0.75 + 2: Scale current by 1.0 + 3: Scale current by 1.5 + Pins on the device (for linking into audio routes) for RT5639/RT5640: * DMIC1 diff --git a/Documentation/devicetree/bindings/sound/rt5645.txt b/Documentation/devicetree/bindings/sound/rt5645.txt index 7cee1f518f59..a03f9a872a71 100644 --- a/Documentation/devicetree/bindings/sound/rt5645.txt +++ b/Documentation/devicetree/bindings/sound/rt5645.txt @@ -69,4 +69,4 @@ codec: rt5650@1a { realtek,dmic-en = "true"; realtek,en-jd-func = "true"; realtek,jd-mode = <3>; -};
\ No newline at end of file +}; diff --git a/Documentation/devicetree/bindings/sound/rt5651.txt b/Documentation/devicetree/bindings/sound/rt5651.txt index b85221864cec..a41199a5cd79 100644 --- a/Documentation/devicetree/bindings/sound/rt5651.txt +++ b/Documentation/devicetree/bindings/sound/rt5651.txt @@ -50,7 +50,7 @@ Pins on the device (for linking into audio routes) for RT5651: Example: -codec: rt5651@1a { +rt5651: codec@1a { compatible = "realtek,rt5651"; reg = <0x1a>; realtek,dmic-en = "true"; diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt index 497bcfc58b71..23386446c63d 100644 --- a/Documentation/devicetree/bindings/sound/rt5663.txt +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -47,7 +47,7 @@ Pins on the device (for linking into audio routes) for RT5663: Example: -codec: rt5663@12 { +rt5663: codec@12 { compatible = "realtek,rt5663"; reg = <0x12>; interrupts = <7 IRQ_TYPE_EDGE_FALLING>; diff --git a/Documentation/devicetree/bindings/sound/rt5668.txt b/Documentation/devicetree/bindings/sound/rt5668.txt new file mode 100644 index 000000000000..c88b96e7764b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5668.txt @@ -0,0 +1,50 @@ +RT5668B audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5668b" + +- reg : The I2C address of the device. + +Optional properties: + +- interrupts : The CODEC's interrupt output. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO2 pin as dmic1 data pin + 2: using GPIO5 pin as dmic1 data pin + +- realtek,dmic1-clk-pin + 0: using GPIO1 pin as dmic1 clock pin + 1: using GPIO3 pin as dmic1 clock pin + +- realtek,jd-src + 0: No JD is used + 1: using JD1 as JD source + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Pins on the device (for linking into audio routes) for RT5668B: + + * DMIC L1 + * DMIC R1 + * IN1P + * HPOL + * HPOR + +Example: + +rt5668 { + compatible = "realtek,rt5668b"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(U, 6) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_HIGH>; + realtek,dmic1-data-pin = <1>; + realtek,dmic1-clk-pin = <1>; + realtek,jd-src = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 9a36c7e2a143..0f214457476f 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -39,7 +39,7 @@ VDDIO 1.8V 2.5V 3.3V Example: -codec: sgtl5000@a { +sgtl5000: codec@a { compatible = "fsl,sgtl5000"; reg = <0x0a>; #sound-dai-cells = <0>; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index 17c13e74667d..a4c72d09cd45 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -86,6 +86,11 @@ Optional CPU/CODEC subnodes properties: in dai startup() and disabled with clk_disable_unprepare() in dai shutdown(). + If a clock is specified and a + multiplication factor is given with + mclk-fs, the clock will be set to the + calculated mclk frequency when the + stream starts. - system-clock-direction-out : specifies clock direction as 'out' on initialization. It is useful for some aCPUs with fixed clocks. diff --git a/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt b/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt index 4bda52042402..58c341300552 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt +++ b/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt @@ -18,7 +18,7 @@ Required properties: See Documentation/devicetree/bindings/dma/stm32-dma.txt. - dma-names: Identifier for each DMA request line. Must be "tx" and "rx". - pinctrl-names: should contain only value "default" - - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/pinctrl-stm32.txt + - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt Optional properties: - resets: Reference to a reset controller asserting the reset controller diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt index f301cdf0b7e6..3a3fc506e43a 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt +++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt @@ -37,7 +37,7 @@ SAI subnodes required properties: "tx": if sai sub-block is configured as playback DAI "rx": if sai sub-block is configured as capture DAI - pinctrl-names: should contain only value "default" - - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/pinctrl-stm32.txt + - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt SAI subnodes Optional properties: - st,sync: specify synchronization mode. diff --git a/Documentation/devicetree/bindings/sound/ti,tas6424.txt b/Documentation/devicetree/bindings/sound/ti,tas6424.txt index 1c4ada0eef4e..eacb54f34188 100644 --- a/Documentation/devicetree/bindings/sound/ti,tas6424.txt +++ b/Documentation/devicetree/bindings/sound/ti,tas6424.txt @@ -6,6 +6,8 @@ Required properties: - compatible: "ti,tas6424" - TAS6424 - reg: I2C slave address - sound-dai-cells: must be equal to 0 + - standby-gpios: GPIO used to shut the TAS6424 down. + - mute-gpios: GPIO used to mute all the outputs Example: diff --git a/Documentation/devicetree/bindings/sound/tscs42xx.txt b/Documentation/devicetree/bindings/sound/tscs42xx.txt index 2ac2f0996697..7eea32e9d078 100644 --- a/Documentation/devicetree/bindings/sound/tscs42xx.txt +++ b/Documentation/devicetree/bindings/sound/tscs42xx.txt @@ -8,9 +8,15 @@ Required Properties: - reg : <0x71> for analog mic <0x69> for digital mic + - clock-names: Must one of the following "mclk1", "xtal", "mclk2" + + - clocks: phandle of the clock that provides the codec sysclk + Example: wookie: codec@69 { compatible = "tempo,tscs42A2"; reg = <0x69>; + clock-names = "xtal"; + clocks = <&audio_xtal>; }; diff --git a/Documentation/devicetree/bindings/sound/tscs454.txt b/Documentation/devicetree/bindings/sound/tscs454.txt new file mode 100644 index 000000000000..3ba3e2d2c206 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tscs454.txt @@ -0,0 +1,23 @@ +TSCS454 Audio CODEC + +Required Properties: + + - compatible : "tempo,tscs454" + + - reg : <0x69> + + - clock-names: Must one of the following "xtal", "mclk1", "mclk2" + + - clocks: phandle of the clock that provides the codec sysclk + + Note: If clock is not provided then bit clock is assumed + +Example: + +redwood: codec@69 { + #sound-dai-cells = <1>; + compatible = "tempo,tscs454"; + reg = <0x69>; + clock-names = "mclk1"; + clocks = <&audio_mclk>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8510.txt b/Documentation/devicetree/bindings/sound/wm8510.txt index fa1a32b85577..e6b6cc041f89 100644 --- a/Documentation/devicetree/bindings/sound/wm8510.txt +++ b/Documentation/devicetree/bindings/sound/wm8510.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8510@1a { +wm8510: codec@1a { compatible = "wlf,wm8510"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8523.txt b/Documentation/devicetree/bindings/sound/wm8523.txt index 04746186b283..f3a6485f4b8a 100644 --- a/Documentation/devicetree/bindings/sound/wm8523.txt +++ b/Documentation/devicetree/bindings/sound/wm8523.txt @@ -10,7 +10,7 @@ Required properties: Example: -codec: wm8523@1a { +wm8523: codec@1a { compatible = "wlf,wm8523"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8524.txt b/Documentation/devicetree/bindings/sound/wm8524.txt index 0f0553563fc1..f6c0c263b135 100644 --- a/Documentation/devicetree/bindings/sound/wm8524.txt +++ b/Documentation/devicetree/bindings/sound/wm8524.txt @@ -10,7 +10,7 @@ Required properties: Example: -codec: wm8524 { +wm8524: codec { compatible = "wlf,wm8524"; wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8580.txt b/Documentation/devicetree/bindings/sound/wm8580.txt index 78fce9b14954..ff3f9f5f2111 100644 --- a/Documentation/devicetree/bindings/sound/wm8580.txt +++ b/Documentation/devicetree/bindings/sound/wm8580.txt @@ -10,7 +10,7 @@ Required properties: Example: -codec: wm8580@1a { +wm8580: codec@1a { compatible = "wlf,wm8580"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8711.txt b/Documentation/devicetree/bindings/sound/wm8711.txt index 8ed9998cd23c..c30a1387c4bf 100644 --- a/Documentation/devicetree/bindings/sound/wm8711.txt +++ b/Documentation/devicetree/bindings/sound/wm8711.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8711@1a { +wm8711: codec@1a { compatible = "wlf,wm8711"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8728.txt b/Documentation/devicetree/bindings/sound/wm8728.txt index a8b5c3668e60..a3608b4c78b9 100644 --- a/Documentation/devicetree/bindings/sound/wm8728.txt +++ b/Documentation/devicetree/bindings/sound/wm8728.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8728@1a { +wm8728: codec@1a { compatible = "wlf,wm8728"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8731.txt b/Documentation/devicetree/bindings/sound/wm8731.txt index 236690e99b87..f660d9bb0e69 100644 --- a/Documentation/devicetree/bindings/sound/wm8731.txt +++ b/Documentation/devicetree/bindings/sound/wm8731.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8731@1a { +wm8731: codec@1a { compatible = "wlf,wm8731"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8737.txt b/Documentation/devicetree/bindings/sound/wm8737.txt index 4bc2cea3b140..eda1ec6a7563 100644 --- a/Documentation/devicetree/bindings/sound/wm8737.txt +++ b/Documentation/devicetree/bindings/sound/wm8737.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8737@1a { +wm8737: codec@1a { compatible = "wlf,wm8737"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8741.txt b/Documentation/devicetree/bindings/sound/wm8741.txt index a13315408719..b69e196c741c 100644 --- a/Documentation/devicetree/bindings/sound/wm8741.txt +++ b/Documentation/devicetree/bindings/sound/wm8741.txt @@ -21,7 +21,7 @@ Optional properties: Example: -codec: wm8741@1a { +wm8741: codec@1a { compatible = "wlf,wm8741"; reg = <0x1a>; diff --git a/Documentation/devicetree/bindings/sound/wm8750.txt b/Documentation/devicetree/bindings/sound/wm8750.txt index 8db239fd5ecd..682f221f6f38 100644 --- a/Documentation/devicetree/bindings/sound/wm8750.txt +++ b/Documentation/devicetree/bindings/sound/wm8750.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8750@1a { +wm8750: codec@1a { compatible = "wlf,wm8750"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8753.txt b/Documentation/devicetree/bindings/sound/wm8753.txt index 8eee61282105..eca9e5a825a9 100644 --- a/Documentation/devicetree/bindings/sound/wm8753.txt +++ b/Documentation/devicetree/bindings/sound/wm8753.txt @@ -34,7 +34,7 @@ Pins on the device (for linking into audio routes): Example: -codec: wm8753@1a { +wm8753: codec@1a { compatible = "wlf,wm8753"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8770.txt b/Documentation/devicetree/bindings/sound/wm8770.txt index 866e00ca150b..cac762a1105d 100644 --- a/Documentation/devicetree/bindings/sound/wm8770.txt +++ b/Documentation/devicetree/bindings/sound/wm8770.txt @@ -10,7 +10,7 @@ Required properties: Example: -codec: wm8770@1 { +wm8770: codec@1 { compatible = "wlf,wm8770"; reg = <1>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8776.txt b/Documentation/devicetree/bindings/sound/wm8776.txt index 3b9ca49abc2b..01173369c3ed 100644 --- a/Documentation/devicetree/bindings/sound/wm8776.txt +++ b/Documentation/devicetree/bindings/sound/wm8776.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8776@1a { +wm8776: codec@1a { compatible = "wlf,wm8776"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8804.txt b/Documentation/devicetree/bindings/sound/wm8804.txt index 6fd124b16496..2c1641c17a91 100644 --- a/Documentation/devicetree/bindings/sound/wm8804.txt +++ b/Documentation/devicetree/bindings/sound/wm8804.txt @@ -19,7 +19,7 @@ Optional properties: Example: -codec: wm8804@1a { +wm8804: codec@1a { compatible = "wlf,wm8804"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8903.txt b/Documentation/devicetree/bindings/sound/wm8903.txt index afc51caf1137..6371c2434afe 100644 --- a/Documentation/devicetree/bindings/sound/wm8903.txt +++ b/Documentation/devicetree/bindings/sound/wm8903.txt @@ -57,7 +57,7 @@ Pins on the device (for linking into audio routes): Example: -codec: wm8903@1a { +wm8903: codec@1a { compatible = "wlf,wm8903"; reg = <0x1a>; interrupts = < 347 >; diff --git a/Documentation/devicetree/bindings/sound/wm8960.txt b/Documentation/devicetree/bindings/sound/wm8960.txt index 2deb8a3da9c5..6d29ac3750ee 100644 --- a/Documentation/devicetree/bindings/sound/wm8960.txt +++ b/Documentation/devicetree/bindings/sound/wm8960.txt @@ -23,7 +23,7 @@ Optional properties: Example: -codec: wm8960@1a { +wm8960: codec@1a { compatible = "wlf,wm8960"; reg = <0x1a>; diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt index 7f82b59ec8f9..dcfa9a3369fd 100644 --- a/Documentation/devicetree/bindings/sound/wm8962.txt +++ b/Documentation/devicetree/bindings/sound/wm8962.txt @@ -24,7 +24,7 @@ Optional properties: Example: -codec: wm8962@1a { +wm8962: codec@1a { compatible = "wlf,wm8962"; reg = <0x1a>; diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt index 68c4e8d96bed..4a9dead1b7d3 100644 --- a/Documentation/devicetree/bindings/sound/wm8994.txt +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -59,7 +59,7 @@ Optional properties: Example: -codec: wm8994@1a { +wm8994: codec@1a { compatible = "wlf,wm8994"; reg = <0x1a>; diff --git a/Documentation/devicetree/bindings/spi/spi-st-ssc.txt b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt index fe54959ec957..1bdc4709e474 100644 --- a/Documentation/devicetree/bindings/spi/spi-st-ssc.txt +++ b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt @@ -9,7 +9,7 @@ Required properties: - clocks : Must contain an entry for each name in clock-names See ../clk/* - pinctrl-names : Uses "default", can use "sleep" if provided - See ../pinctrl/pinctrl-binding.txt + See ../pinctrl/pinctrl-bindings.txt Optional properties: - cs-gpios : List of GPIO chip selects diff --git a/Documentation/devicetree/bindings/submitting-patches.txt b/Documentation/devicetree/bindings/submitting-patches.txt index 274058c583dd..de0d6090c0fd 100644 --- a/Documentation/devicetree/bindings/submitting-patches.txt +++ b/Documentation/devicetree/bindings/submitting-patches.txt @@ -6,7 +6,14 @@ I. For patch submitters 0) Normal patch submission rules from Documentation/process/submitting-patches.rst applies. - 1) The Documentation/ portion of the patch should be a separate patch. + 1) The Documentation/ and include/dt-bindings/ portion of the patch should + be a separate patch. The preferred subject prefix for binding patches is: + + "dt-bindings: <binding dir>: ..." + + The 80 characters of the subject are precious. It is recommended to not + use "Documentation" or "doc" because that is implied. All bindings are + docs. Repeating "binding" again should also be avoided. 2) Submit the entire series to the devicetree mailinglist at diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index b957acff57aa..ad648d93d961 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -12,7 +12,6 @@ "samsung,exynos5420-tmu-ext-triminfo" for TMU channels 2, 3 and 4 Exynos5420 (Must pass triminfo base and triminfo clock) "samsung,exynos5433-tmu" - "samsung,exynos5440-tmu" "samsung,exynos7-tmu" - interrupt-parent : The phandle for the interrupt controller - reg : Address range of the thermal registers. For soc's which has multiple @@ -68,18 +67,7 @@ Example 1): #thermal-sensor-cells = <0>; }; -Example 2): - - tmuctrl_0: tmuctrl@160118 { - compatible = "samsung,exynos5440-tmu"; - reg = <0x160118 0x230>, <0x160368 0x10>; - interrupts = <0 58 0>; - clocks = <&clock 21>; - clock-names = "tmu_apbif"; - #thermal-sensor-cells = <0>; - }; - -Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") +Example 2): (In case of Exynos5420 "with misplaced TRIMINFO register") tmu_cpu2: tmu@10068000 { compatible = "samsung,exynos5420-tmu-ext-triminfo"; reg = <0x10068000 0x100>, <0x1006c000 0x4>; diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt b/Documentation/devicetree/bindings/thermal/imx-thermal.txt index 379eb763073e..823e4176eef8 100644 --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt @@ -1,8 +1,13 @@ * Temperature Monitor (TEMPMON) on Freescale i.MX SoCs Required properties: -- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-tempmon" for i.MX6SX. - i.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC, +- compatible : must be one of following: + - "fsl,imx6q-tempmon" for i.MX6Q, + - "fsl,imx6sx-tempmon" for i.MX6SX, + - "fsl,imx7d-tempmon" for i.MX7S/D. +- interrupts : the interrupt output of the controller: + i.MX6Q has one IRQ which will be triggered when temperature is higher than high threshold, + i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC, when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature is higher than panic threshold, system will auto reboot by SRC module. - fsl,tempmon : phandle pointer to system controller that contains TEMPMON diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt index 0d73ea5e9c0c..41d6a443ad66 100644 --- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt @@ -12,6 +12,7 @@ Required properties: - "mediatek,mt8173-thermal" : For MT8173 family of SoCs - "mediatek,mt2701-thermal" : For MT2701 family of SoCs - "mediatek,mt2712-thermal" : For MT2712 family of SoCs + - "mediatek,mt7622-thermal" : For MT7622 SoC - reg: Address range of the thermal controller - interrupts: IRQ for the thermal controller - clocks, clock-names: Clocks needed for the thermal controller. required diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt index 292ed89d900b..06195e8f35e2 100644 --- a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt +++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt @@ -8,6 +8,7 @@ Required properties: - reg: Address range of the thermal registers - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. +- #qcom,sensors: Number of sensors in tsens block - Refer to Documentation/devicetree/bindings/nvmem/nvmem.txt to know how to specify nvmem cells diff --git a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt index fdf5caa6229b..cfa154bb0fa7 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt @@ -9,6 +9,7 @@ Required properties: Examples with soctypes are: - "renesas,r8a7795-thermal" (R-Car H3) - "renesas,r8a7796-thermal" (R-Car M3-W) + - "renesas,r8a77965-thermal" (R-Car M3-N) - reg : Address ranges of the thermal registers. Each sensor needs one address range. Sorting must be done in increasing order according to datasheet, i.e. @@ -18,7 +19,7 @@ Required properties: Optional properties: -- interrupts : interrupts routed to the TSC (3 for H3 and M3-W) +- interrupts : interrupts routed to the TSC (3 for H3, M3-W and M3-N) - power-domain : Must contain a reference to the power domain. This property is mandatory if the thermal sensor instance is part of a controllable power domain. @@ -27,9 +28,9 @@ Example: tsc: thermal@e6198000 { compatible = "renesas,r8a7795-thermal"; - reg = <0 0xe6198000 0 0x68>, - <0 0xe61a0000 0 0x5c>, - <0 0xe61a8000 0 0x5c>; + reg = <0 0xe6198000 0 0x100>, + <0 0xe61a0000 0 0x100>, + <0 0xe61a8000 0 0x100>; interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 349e635f2d87..67c563f1b4c4 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -3,7 +3,8 @@ Required properties: - compatible : "renesas,thermal-<soctype>", "renesas,rcar-gen2-thermal" (with thermal-zone) or - "renesas,rcar-thermal" (without thermal-zone) as fallback. + "renesas,rcar-thermal" (without thermal-zone) as + fallback except R-Car D3. Examples with soctypes are: - "renesas,thermal-r8a73a4" (R-Mobile APE6) - "renesas,thermal-r8a7743" (RZ/G1M) @@ -12,13 +13,15 @@ Required properties: - "renesas,thermal-r8a7791" (R-Car M2-W) - "renesas,thermal-r8a7792" (R-Car V2H) - "renesas,thermal-r8a7793" (R-Car M2-N) + - "renesas,thermal-r8a77995" (R-Car D3) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register if it has "interrupts". Option properties: -- interrupts : use interrupt +- interrupts : If present should contain 3 interrupts for + R-Car D3 or 1 interrupt otherwise. Example (non interrupt support): diff --git a/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt b/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt index 686c0b42ed3f..ceb92a95727a 100644 --- a/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt @@ -8,6 +8,7 @@ Required properties: - compatible : - "socionext,uniphier-pxs2-thermal" : For UniPhier PXs2 SoC - "socionext,uniphier-ld20-thermal" : For UniPhier LD20 SoC + - "socionext,uniphier-pxs3-thermal" : For UniPhier PXs3 SoC - interrupts : IRQ for the temperature alarm - #thermal-sensor-cells : Should be 0. See ./thermal.txt for details. diff --git a/Documentation/devicetree/bindings/nios2/timer.txt b/Documentation/devicetree/bindings/timer/altr,timer-1.0.txt index 904a5846d7ac..904a5846d7ac 100644 --- a/Documentation/devicetree/bindings/nios2/timer.txt +++ b/Documentation/devicetree/bindings/timer/altr,timer-1.0.txt diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/timer/arm,arch_timer.txt index 68301b77e854..68301b77e854 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/timer/arm,arch_timer.txt diff --git a/Documentation/devicetree/bindings/arm/armv7m_systick.txt b/Documentation/devicetree/bindings/timer/arm,armv7m-systick.txt index 7cf4a24601eb..7cf4a24601eb 100644 --- a/Documentation/devicetree/bindings/arm/armv7m_systick.txt +++ b/Documentation/devicetree/bindings/timer/arm,armv7m-systick.txt diff --git a/Documentation/devicetree/bindings/arm/global_timer.txt b/Documentation/devicetree/bindings/timer/arm,global_timer.txt index bdae3a818793..bdae3a818793 100644 --- a/Documentation/devicetree/bindings/arm/global_timer.txt +++ b/Documentation/devicetree/bindings/timer/arm,global_timer.txt diff --git a/Documentation/devicetree/bindings/arm/twd.txt b/Documentation/devicetree/bindings/timer/arm,twd.txt index 383ea19c2bf0..383ea19c2bf0 100644 --- a/Documentation/devicetree/bindings/arm/twd.txt +++ b/Documentation/devicetree/bindings/timer/arm,twd.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt b/Documentation/devicetree/bindings/timer/fsl,gtm.txt index 9a33efded4bc..9a33efded4bc 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt +++ b/Documentation/devicetree/bindings/timer/fsl,gtm.txt diff --git a/Documentation/devicetree/bindings/arm/mrvl/timer.txt b/Documentation/devicetree/bindings/timer/mrvl,mmp-timer.txt index 9a6e251462e7..9a6e251462e7 100644 --- a/Documentation/devicetree/bindings/arm/mrvl/timer.txt +++ b/Documentation/devicetree/bindings/timer/mrvl,mmp-timer.txt diff --git a/Documentation/devicetree/bindings/arm/msm/timer.txt b/Documentation/devicetree/bindings/timer/qcom,msm-timer.txt index 5e10c345548f..5e10c345548f 100644 --- a/Documentation/devicetree/bindings/arm/msm/timer.txt +++ b/Documentation/devicetree/bindings/timer/qcom,msm-timer.txt diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index d740989eb569..b40add2d9bb4 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -22,6 +22,10 @@ Required Properties: - "renesas,r8a73a4-cmt0" for the 32-bit CMT0 device included in r8a73a4. - "renesas,r8a73a4-cmt1" for the 48-bit CMT1 device included in r8a73a4. + - "renesas,r8a7743-cmt0" for the 32-bit CMT0 device included in r8a7743. + - "renesas,r8a7743-cmt1" for the 48-bit CMT1 device included in r8a7743. + - "renesas,r8a7745-cmt0" for the 32-bit CMT0 device included in r8a7745. + - "renesas,r8a7745-cmt1" for the 48-bit CMT1 device included in r8a7745. - "renesas,r8a7790-cmt0" for the 32-bit CMT0 device included in r8a7790. - "renesas,r8a7790-cmt1" for the 48-bit CMT1 device included in r8a7790. - "renesas,r8a7791-cmt0" for the 32-bit CMT0 device included in r8a7791. @@ -31,10 +35,12 @@ Required Properties: - "renesas,r8a7794-cmt0" for the 32-bit CMT0 device included in r8a7794. - "renesas,r8a7794-cmt1" for the 48-bit CMT1 device included in r8a7794. - - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2. - - "renesas,rcar-gen2-cmt1" for 48-bit CMT1 devices included in R-Car Gen2. - These are fallbacks for r8a73a4 and all the R-Car Gen2 - entries listed above. + - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2 + and RZ/G1. + - "renesas,rcar-gen2-cmt1" for 48-bit CMT1 devices included in R-Car Gen2 + and RZ/G1. + These are fallbacks for r8a73a4, R-Car Gen2 and RZ/G1 entries + listed above. - reg: base address and length of the registers block for the timer module. - interrupts: interrupt-specifier for the timer, one per channel. diff --git a/Documentation/devicetree/bindings/arm/spear-timer.txt b/Documentation/devicetree/bindings/timer/st,spear-timer.txt index c0017221cf55..c0017221cf55 100644 --- a/Documentation/devicetree/bindings/arm/spear-timer.txt +++ b/Documentation/devicetree/bindings/timer/st,spear-timer.txt diff --git a/Documentation/devicetree/bindings/c6x/timer64.txt b/Documentation/devicetree/bindings/timer/ti,c64x+timer64.txt index 95911fe70224..95911fe70224 100644 --- a/Documentation/devicetree/bindings/c6x/timer64.txt +++ b/Documentation/devicetree/bindings/timer/ti,c64x+timer64.txt diff --git a/Documentation/devicetree/bindings/arm/omap/timer.txt b/Documentation/devicetree/bindings/timer/ti,timer.txt index d02e27c764ec..d02e27c764ec 100644 --- a/Documentation/devicetree/bindings/arm/omap/timer.txt +++ b/Documentation/devicetree/bindings/timer/ti,timer.txt diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt b/Documentation/devicetree/bindings/timer/via,vt8500-timer.txt index 901c73f0d8ef..901c73f0d8ef 100644 --- a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt +++ b/Documentation/devicetree/bindings/timer/via,vt8500-timer.txt diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 0e03344e2e8b..2e9318151df7 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -76,6 +76,10 @@ Optional properties: needs to make sure it does not send more than 90% maximum_periodic_data_per_frame. The use case is multiple transactions, but less frame rate. +- mux-controls: The mux control for toggling host/device output of this + controller. It's expected that a mux state of 0 indicates device mode and a + mux state of 1 indicates host mode. +- mux-control-names: Shall be "usb_switch" if mux-controls is specified. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one @@ -102,4 +106,6 @@ Example: rx-burst-size-dword = <0x10>; extcon = <0>, <&usb_id>; phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 0dbd3083e7dd..7f13ebef06cb 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -7,6 +7,26 @@ Required properties: - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. + - clock-names: should contain "ref", "bus_early", "suspend" + - clocks: list of phandle and clock specifier pairs corresponding to + entries in the clock-names property. + +Exception for clocks: + clocks are optional if the parent node (i.e. glue-layer) is compatible to + one of the following: + "amlogic,meson-axg-dwc3" + "amlogic,meson-gxl-dwc3" + "cavium,octeon-7130-usb-uctl" + "qcom,dwc3" + "samsung,exynos5250-dwusb3" + "samsung,exynos7-dwusb3" + "sprd,sc9860-dwc3" + "st,stih407-dwc3" + "ti,am437x-dwc3" + "ti,dwc3" + "ti,keystone-dwc3" + "rockchip,rk3399-dwc3" + "xlnx,zynqmp-dwc3" Optional properties: - usb-phy : array of phandle for the PHY device. The first element @@ -15,6 +35,7 @@ Optional properties: - phys: from the *Generic PHY* bindings - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" or "usb3-phy". + - resets: a single pair of phandle and reset specifier - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index 472facfa5a71..6087dc7f209e 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -6,12 +6,6 @@ Required properties : - interrupts : Interrupt specifier Optional properties : -- fcs,max-sink-microvolt : Maximum voltage to negotiate when configured as sink -- fcs,max-sink-microamp : Maximum current to negotiate when configured as sink -- fcs,max-sink-microwatt : Maximum power to negotiate when configured as sink - If this is less then max-sink-microvolt * - max-sink-microamp then the configured current will - be clamped. - fcs,operating-sink-microwatt : Minimum amount of power accepted from a sink when negotiating diff --git a/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt new file mode 100644 index 000000000000..f4633496b122 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt @@ -0,0 +1,45 @@ +HiSilicon STB xHCI + +The device node for HiSilicon STB xHCI host controller + +Required properties: + - compatible: should be "hisilicon,hi3798cv200-xhci" + - reg: specifies physical base address and size of the registers + - interrupts : interrupt used by the controller + - clocks: a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names: must contain + "bus": for bus clock + "utmi": for utmi clock + "pipe": for pipe clock + "suspend": for suspend clock + - resets: a list of phandle and reset specifier pairs as listed in + reset-names property. + - reset-names: must contain + "soft": for soft reset + - phys: a list of phandle + phy specifier pairs + - phy-names: must contain at least one of following: + "inno": for inno phy + "combo": for combo phy + +Optional properties: + - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM + - usb3-lpm-capable: determines if platform is USB3 LPM capable + - imod-interval-ns: default interrupt moderation interval is 40000ns + +Example: + +xhci0: xchi@f98a0000 { + compatible = "hisilicon,hi3798cv200-xhci"; + reg = <0xf98a0000 0x10000>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_USB3_BUS_CLK>, + <&crg HISTB_USB3_UTMI_CLK>, + <&crg HISTB_USB3_PIPE_CLK>, + <&crg HISTB_USB3_SUSPEND_CLK>; + clock-names = "bus", "utmi", "pipe", "suspend"; + resets = <&crg 0xb0 12>; + reset-names = "soft"; + phys = <&usb2_phy1_port1 0>, <&combphy0 PHY_TYPE_USB3>; + phy-names = "inno", "combo"; +}; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index bc8a2fa5d2bf..95afdcf3c337 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -1,54 +1,95 @@ Qualcomm SuperSpeed DWC3 USB SoC controller Required properties: -- compatible: should contain "qcom,dwc3" +- compatible: Compatible list, contains + "qcom,dwc3" + "qcom,msm8996-dwc3" for msm8996 SOC. + "qcom,sdm845-dwc3" for sdm845 SOC. +- reg: Offset and length of register set for QSCRATCH wrapper +- power-domains: specifies a phandle to PM domain provider node - clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock-names -- clock-names: Should contain the following: +- clock-names: Should contain the following: "core" Master/Core clock, have to be >= 125 MHz for SS operation and >= 60MHz for HS operation + "mock_utmi" Mock utmi clock needed for ITP/SOF generation in + host mode. Its frequency should be 19.2MHz. + "sleep" Sleep clock, used for wakeup when USB3 core goes + into low power mode (U3). Optional clocks: - "iface" System bus AXI clock. Not present on all platforms - "sleep" Sleep clock, used when USB3 core goes into low - power mode (U3). + "iface" System bus AXI clock. + Not present on "qcom,msm8996-dwc3" compatible. + "cfg_noc" System Config NOC clock. + Not present on "qcom,msm8996-dwc3" compatible. +- assigned-clocks: Should be: + MOCK_UTMI_CLK + MASTER_CLK +- assigned-clock-rates: Should be: + 19.2Mhz (192000000) for MOCK_UTMI_CLK + >=125Mhz (125000000) for MASTER_CLK in SS mode + >=60Mhz (60000000) for MASTER_CLK in HS mode + +Optional properties: +- resets: Phandle to reset control that resets core and wrapper. +- interrupts: specifies interrupts from controller wrapper used + to wakeup from low power/susepnd state. Must contain + one or more entry for interrupt-names property +- interrupt-names: Must include the following entries: + - "hs_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB2 bus + - "ss_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB3 bus + - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate + interrupts for any wakeup event on DM and DP lines +- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement. + Used when dwc3 operates without SSPHY and only + HS/FS/LS modes are supported. Required child node: A child node must exist to represent the core DWC3 IP block. The name of the node is not important. The content of the node is defined in dwc3.txt. Phy documentation is provided in the following places: -Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt +Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY +Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY Example device nodes: hs_phy: phy@100f8800 { - compatible = "qcom,dwc3-hs-usb-phy"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - + compatible = "qcom,qusb2-v2-phy"; + ... }; ss_phy: phy@100f8830 { - compatible = "qcom,dwc3-ss-usb-phy"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - + compatible = "qcom,qmp-v3-usb3-phy"; + ... }; - usb3_0: usb30@0 { + usb3_0: usb30@a6f8800 { compatible = "qcom,dwc3"; + reg = <0xa6f8800 0x400>; #address-cells = <1>; #size-cells = <1>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - ranges; + interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>; + interrupt-names = "hs_phy_irq", "ss_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + clock-names = "core", "mock_utmi", "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <133000000>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + reset-names = "core_reset"; + power-domains = <&gcc USB30_PRIM_GDSC>; + qcom,select-utmi-as-pipe-clk; dwc3@10000000 { compatible = "snps,dwc3"; diff --git a/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt new file mode 100644 index 000000000000..09e847e92e5e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt @@ -0,0 +1,17 @@ +Richtek RT1711H TypeC PD Controller. + +Required properties: + - compatible : Must be "richtek,rt1711h". + - reg : Must be 0x4e, it's slave address of RT1711H. + - interrupt-parent : the phandle for the interrupt controller that + provides interrupts for this device. + - interrupts : <a b> where a is the interrupt number and b represents an + encoding of the sense and level information for the interrupt. + +Example : +rt1711h@4e { + compatible = "richtek,rt1711h"; + reg = <0x4e>; + interrupt-parent = <&gpio26>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; +}; diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt index 50a31536e975..252a05c5d976 100644 --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt @@ -16,7 +16,7 @@ A child node must exist to represent the core DWC3 IP block. The name of the node is not important. The content of the node is defined in dwc3.txt. Phy documentation is provided in the following places: -Documentation/devicetree/bindings/phy/rockchip,dwc3-usb-phy.txt +Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt Example device nodes: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index a38d8bfae19c..7cad066191ee 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -32,6 +32,7 @@ andestech Andes Technology Corporation apm Applied Micro Circuits Corporation (APM) aptina Aptina Imaging arasan Arasan Chip Systems +archermind ArcherMind Technology (Nanjing) Co., Ltd. arctic Arctic Sand aries Aries Embedded GmbH arm ARM Ltd. @@ -47,6 +48,7 @@ auvidea Auvidea GmbH avago Avago Technologies avia avia semiconductor avic Shanghai AVIC Optoelectronics Co., Ltd. +avnet Avnet, Inc. axentia Axentia Technologies AB axis Axis Communications AB bananapi BIPAI KEJI LIMITED @@ -56,6 +58,7 @@ bosch Bosch Sensortec GmbH boundary Boundary Devices Inc. brcm Broadcom Corporation buffalo Buffalo, Inc. +bticino Bticino International calxeda Calxeda capella Capella Microsystems, Inc cascoda Cascoda, Ltd. @@ -75,6 +78,7 @@ cnxt Conexant Systems, Inc. compulab CompuLab Ltd. cortina Cortina Systems, Inc. cosmic Cosmic Circuits +crane Crane Connectivity Solutions creative Creative Technology Ltd crystalfontz Crystalfontz America, Inc. cubietech Cubietech, Ltd. @@ -185,6 +189,7 @@ khadas Khadas kiebackpeter Kieback & Peter GmbH kinetic Kinetic Technologies kingnovel Kingnovel Technology Co., Ltd. +koe Kaohsiung Opto-Electronics Inc. kosagi Sutajio Ko-Usagi PTE Ltd. kyo Kyocera Corporation lacie LaCie @@ -199,11 +204,13 @@ linaro Linaro Limited linksys Belkin International, Inc. (Linksys) linux Linux-specific binding lltc Linear Technology Corporation +logicpd Logic PD, Inc. lsi LSI Corp. (LSI Logic) lwn Liebherr-Werk Nenzing GmbH macnica Macnica Americas marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products +mbvl Mobiveil Inc. mcube mCube meas Measurement Specialties mediatek MediaTek Inc. @@ -279,6 +286,7 @@ pine64 Pine64 pixcir PIXCIR MICROELECTRONICS Co., Ltd plathome Plat'Home Co., Ltd. plda PLDA +portwell Portwell Inc. poslab Poslab Technology Co., Ltd. powervr PowerVR (deprecated, use img) probox2 PROBOX2 (by W2COMP Co., Ltd.) @@ -318,6 +326,7 @@ sgx SGX Sensortech sharp Sharp Corporation shimafuji Shimafuji Electric, Inc. si-en Si-En Technology Ltd. +sifive SiFive, Inc. sigma Sigma Designs, Inc. sii Seiko Instruments, Inc. sil Silicon Image @@ -393,6 +402,7 @@ vot Vision Optical Technology Co., Ltd. wd Western Digital Corp. wetek WeTek Electronics, limited. wexler Wexler +wi2wi Wi2Wi, Inc. winbond Winbond Electronics corp. winstar Winstar Display Corp. wlf Wolfson Microelectronics diff --git a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt index cb44918f01a8..ce1cb72d5345 100644 --- a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt @@ -3,10 +3,15 @@ Ingenic Watchdog Timer (WDT) Controller for JZ4740 & JZ4780 Required properties: compatible: "ingenic,jz4740-watchdog" or "ingenic,jz4780-watchdog" reg: Register address and length for watchdog registers +clocks: phandle to the RTC clock +clock-names: should be "rtc" Example: watchdog: jz4740-watchdog@10002000 { compatible = "ingenic,jz4740-watchdog"; - reg = <0x10002000 0x100>; + reg = <0x10002000 0x10>; + + clocks = <&cgu JZ4740_CLK_RTC>; + clock-names = "rtc"; }; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index 74b2f03c1515..f24d802b8056 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -1,18 +1,27 @@ Renesas Watchdog Timer (WDT) Controller Required properties: -- compatible : Should be "renesas,<soctype>-wdt", and - "renesas,rcar-gen3-wdt" or "renesas,rza-wdt" as fallback. + - compatible : Must be "renesas,<soctype>-wdt", followed by a generic + fallback compatible string when compatible with the generic + version. Examples with soctypes are: - - "renesas,r7s72100-wdt" (RZ/A1) + - "renesas,r8a7743-wdt" (RZ/G1M) + - "renesas,r8a7745-wdt" (RZ/G1E) + - "renesas,r8a7790-wdt" (R-Car H2) + - "renesas,r8a7791-wdt" (R-Car M2-W) + - "renesas,r8a7792-wdt" (R-Car V2H) + - "renesas,r8a7793-wdt" (R-Car M2-N) + - "renesas,r8a7794-wdt" (R-Car E2) - "renesas,r8a7795-wdt" (R-Car H3) - "renesas,r8a7796-wdt" (R-Car M3-W) + - "renesas,r8a77965-wdt" (R-Car M3-N) - "renesas,r8a77970-wdt" (R-Car V3M) - "renesas,r8a77995-wdt" (R-Car D3) - - When compatible with the generic version, nodes must list the SoC-specific - version corresponding to the platform first, followed by the generic - version. + - "renesas,r7s72100-wdt" (RZ/A1) + The generic compatible string must be: + - "renesas,rza-wdt" for RZ/A + - "renesas,rcar-gen2-wdt" for R-Car Gen2 and RZ/G + - "renesas,rcar-gen3-wdt" for R-Car Gen3 - reg : Should contain WDT registers location and length - clocks : the clock feeding the watchdog timer. |