drm/i915: enable scrambling

Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.

V2: Addressed review comments from Ville:
 - Do not track scrambling status in DRM layer, track somewhere in
   driver like in intel_crtc_state.
 - Don't talk to monitor at such a low layer, set monitor scrambling
   in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
 - In comments, function names, use "sink" instead of "monitor",
   so that the implementation could be close to the language of
   HDMI spec.

V4: Addressed review comment from Maarten
 - scrambling -> hdmi_scrambling
 - high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
 - Do not modifiy the crtc_state after compute_config. Move all
   scrambling and tmds_clock_ratio calcutations to compute_config.
 - While setting scrambling for source/sink, do not check the
   conditions again, just go by the crtc_state flags. This will
   simplyfy the condition checks.

V6: Addressed review comments from Ville
 - Do not add IS_GLK check in disable/enable function, instead add it
   in compute_config, while setting state flags.
 - Remove unnecessary paranthesis.
 - Simplyfy handle_sink_scrambling function as suggested.
 - Add readout code for scrambling status in get_ddi_config and add a
   check for the same in pipe_config_compare.

V7: Addressed review comments from Ander/Ville
 - No separate function for source scrambling, make it inline
 - Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
 - Do not add platform check while setting source scrambling
 - Use pipe_config instead of crtc->config to set sink scrambling
 - To readout scrambling status, Compare with SCRAMBLING_MASK
   not any of its bits
 - Remove platform check in intel_pipe_config_compare while checking
   scrambling status

V8: Fixed mege conflict, Addressed review comments from Ander
 - Remove the desciption/comment about scrambling fom the caller, move
   it to the function
 - Move the IS_GLK check into scrambling function
 - Fix alignment

V9: Fixed review comments from Ville, Ander
 - Pass the scrambling state variables as bool input to the sink_scrambling
   function and let the disable call be unconditional.
 - Fix alignments in function calls and debug messages.
 - Add kernel doc for function intel_hdmi_handle_sink_scrambling

V10: Rebase

Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com

1 files changed, 7 insertions, 0 deletions

diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 04c8f69fcc62..11b12f412492 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -7829,7 +7829,14 @@ enum {
 #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
 #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
 #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
 #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
+#define  TRANS_DDI_HDMI_SCRAMBLING_MASK (TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE \
+					| TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ \
+					| TRANS_DDI_HDMI_SCRAMBLING)
 
 /* DisplayPort Transport Control */
 #define _DP_TP_CTL_A			0x64040