serial: unify serial bindings into a single dir

Move all bindings in bindings/tty/serial into bindings/serial so we only
have one place dir with serial/uart related bindings in it.

Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

12 files changed, 325 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/serial/arc-uart.txt b/Documentation/devicetree/bindings/serial/arc-uart.txt
new file mode 100644
index 000000000000..5cae2eb686f8
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/arc-uart.txt
@@ -0,0 +1,26 @@
+* Synopsys ARC UART : Non standard UART used in some of the ARC FPGA boards
+
+Required properties:
+- compatible		: "snps,arc-uart"
+- reg			: offset and length of the register set for the device.
+- interrupts		: device interrupt
+- clock-frequency	: the input clock frequency for the UART
+- current-speed		: baud rate for UART
+
+e.g.
+
+arcuart0: serial@c0fc1000 {
+	compatible = "snps,arc-uart";
+	reg = <0xc0fc1000 0x100>;
+	interrupts = <5>;
+	clock-frequency = <80000000>;
+	current-speed = <115200>;
+	status = "okay";
+};
+
+Note: Each port should have an alias correctly numbered in "aliases" node.
+
+e.g.
+aliases {
+	serial0 = &arcuart0;
+};
diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt
new file mode 100644
index 000000000000..2191dcb9f1da
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt
@@ -0,0 +1,43 @@
+* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART)
+
+Required properties:
+- compatible: Should be "atmel,<chip>-usart"
+  The compatible <chip> indicated will be the first SoC to support an
+  additional mode or an USART new feature.
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt
+
+Optional properties:
+- atmel,use-dma-rx: use of PDC or DMA for receiving data
+- atmel,use-dma-tx: use of PDC or DMA for transmitting data
+- add dma bindings for dma transfer:
+	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+		memory peripheral interface and USART DMA channel ID, FIFO configuration.
+		Refer to dma.txt and atmel-dma.txt for details.
+	- dma-names: "rx" for RX channel, "tx" for TX channel.
+
+<chip> compatible description:
+- at91rm9200:  legacy USART support
+- at91sam9260: generic USART implementation for SAM9 SoCs
+
+Example:
+- use PDC:
+	usart0: serial@fff8c000 {
+		compatible = "atmel,at91sam9260-usart";
+		reg = <0xfff8c000 0x4000>;
+		interrupts = <7>;
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+	};
+
+- use DMA:
+	usart0: serial@f001c000 {
+		compatible = "atmel,at91sam9260-usart";
+		reg = <0xf001c000 0x100>;
+		interrupts = <12 4 5>;
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		dmas = <&dma0 2 0x3>,
+		       <&dma0 2 0x204>;
+		dma-names = "tx", "rx";
+	};
diff --git a/Documentation/devicetree/bindings/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt
new file mode 100644
index 000000000000..8e080b893b49
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/efm32-uart.txt
@@ -0,0 +1,20 @@
+* Energymicro efm32 UART
+
+Required properties:
+- compatible : Should be "efm32,uart"
+- reg : Address and length of the register set
+- interrupts : Should contain uart interrupt
+
+Optional properties:
+- location : Decides the location of the USART I/O pins.
+  Allowed range : [0 .. 5]
+  Default: 0
+
+Example:
+
+uart@0x4000c400 {
+	compatible = "efm32,uart";
+	reg = <0x4000c400 0x400>;
+	interrupts = <15>;
+	location = <0>;
+};
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
new file mode 100644
index 000000000000..35ae1fb3537f
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
@@ -0,0 +1,29 @@
+* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
+
+Required properties:
+- compatible : Should be "fsl,<soc>-uart"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain uart interrupt
+
+Optional properties:
+- fsl,uart-has-rtscts : Indicate the uart has rts and cts
+- fsl,irda-mode : Indicate the uart supports irda mode
+- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
+                  is DCE mode by default.
+
+Note: Each uart controller should have an alias correctly numbered
+in "aliases" node.
+
+Example:
+
+aliases {
+	serial0 = &uart1;
+};
+
+uart1: serial@73fbc000 {
+	compatible = "fsl,imx51-uart", "fsl,imx21-uart";
+	reg = <0x73fbc000 0x4000>;
+	interrupts = <31>;
+	fsl,uart-has-rtscts;
+	fsl,dte-mode;
+};
diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
new file mode 100644
index 000000000000..6fd1dd1638dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
@@ -0,0 +1,14 @@
+* Freescale low power universal asynchronous receiver/transmitter (lpuart)
+
+Required properties:
+- compatible : Should be "fsl,<soc>-lpuart"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain uart interrupt
+
+Example:
+
+uart0: serial@40027000 {
+	       compatible = "fsl,vf610-lpuart";
+	       reg = <0x40027000 0x1000>;
+	       interrupts = <0 61 0x00>;
+       };
diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
new file mode 100644
index 000000000000..59a40f18d551
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
@@ -0,0 +1,37 @@
+* Freescale MXS Application UART (AUART)
+
+Required properties:
+- compatible : Should be "fsl,<soc>-auart". The supported SoCs include
+  imx23 and imx28.
+- reg : Address and length of the register set for the device
+- interrupts : Should contain the auart interrupt numbers
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and AUART DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: "rx" for RX channel, "tx" for TX channel.
+
+Optional properties:
+- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines,
+	it also means you enable the DMA support for this UART.
+
+Example:
+auart0: serial@8006a000 {
+	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+	reg = <0x8006a000 0x2000>;
+	interrupts = <112>;
+	dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+	dma-names = "rx", "tx";
+};
+
+Note: Each auart port should have an alias correctly numbered in "aliases"
+node.
+
+Example:
+
+aliases {
+	serial0 = &auart0;
+	serial1 = &auart1;
+	serial2 = &auart2;
+	serial3 = &auart3;
+	serial4 = &auart4;
+};
diff --git a/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt
new file mode 100644
index 000000000000..0d439dfc1aa5
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt
@@ -0,0 +1,14 @@
+* NXP LPC32xx SoC High Speed UART
+
+Required properties:
+- compatible: Should be "nxp,lpc3220-hsuart"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt
+
+Example:
+
+	uart1: serial@40014000 {
+		compatible = "nxp,lpc3220-hsuart";
+		reg = <0x40014000 0x1000>;
+		interrupts = <26 0>;
+	};
diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt
new file mode 100644
index 000000000000..1928a3e83cd0
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/of-serial.txt
@@ -0,0 +1,49 @@
+* UART (Universal Asynchronous Receiver/Transmitter)
+
+Required properties:
+- compatible : one of:
+	- "ns8250"
+	- "ns16450"
+	- "ns16550a"
+	- "ns16550"
+	- "ns16750"
+	- "ns16850"
+	- "nvidia,tegra20-uart"
+	- "nxp,lpc3220-uart"
+	- "ibm,qpace-nwp-serial"
+	- "altr,16550-FIFO32"
+	- "altr,16550-FIFO64"
+	- "altr,16550-FIFO128"
+	- "serial" if the port type is unknown.
+- reg : offset and length of the register set for the device.
+- interrupts : should contain uart interrupt.
+- clock-frequency : the input clock frequency for the UART
+	 or
+  clocks phandle to refer to the clk used as per Documentation/devicetree
+  /bindings/clock/clock-bindings.txt
+
+Optional properties:
+- current-speed : the current active speed of the UART.
+- reg-offset : offset to apply to the mapbase from the start of the registers.
+- reg-shift : quantity to shift the register offsets by.
+- reg-io-width : the size (in bytes) of the IO accesses that should be
+  performed on the device.  There are some systems that require 32-bit
+  accesses to the UART (e.g. TI davinci).
+- used-by-rtas : set to indicate that the port is in use by the OpenFirmware
+  RTAS and should not be registered.
+- no-loopback-test: set to indicate that the port does not implements loopback
+  test mode
+- fifo-size: the fifo size of the UART.
+- auto-flow-control: one way to enable automatic flow control support. The
+  driver is allowed to detect support for the capability even without this
+  property.
+
+Example:
+
+	uart@80230000 {
+		compatible = "ns8250";
+		reg = <0x80230000 0x100>;
+		clock-frequency = <3686400>;
+		interrupts = <10>;
+		reg-shift = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt
new file mode 100644
index 000000000000..a2dfc6522a91
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt
@@ -0,0 +1,33 @@
+* CSR SiRFprimaII/atlasVI Universal Synchronous Asynchronous Receiver/Transmitter *
+
+Required properties:
+- compatible : Should be "sirf,prima2-uart" or "sirf, prima2-usp-uart"
+- reg : Offset and length of the register set for the device
+- interrupts : Should contain uart interrupt
+- fifosize : Should define hardware rx/tx fifo size
+- clocks : Should contain uart clock number
+
+Optional properties:
+- sirf,uart-has-rtscts: we have hardware flow controller pins in hardware
+- rts-gpios: RTS pin for USP-based UART if sirf,uart-has-rtscts is true
+- cts-gpios: CTS pin for USP-based UART if sirf,uart-has-rtscts is true
+
+Example:
+
+uart0: uart@b0050000 {
+	cell-index = <0>;
+	compatible = "sirf,prima2-uart";
+	reg = <0xb0050000 0x1000>;
+	interrupts = <17>;
+	fifosize = <128>;
+	clocks = <&clks 13>;
+};
+
+On the board-specific dts, we can put rts-gpios and cts-gpios like
+
+usp@b0090000 {
+	compatible = "sirf,prima2-usp-uart";
+	sirf,uart-has-rtscts;
+	rts-gpios = <&gpio 15 0>;
+	cts-gpios = <&gpio 46 0>;
+};
diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
new file mode 100644
index 000000000000..f13f1c5be91c
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
@@ -0,0 +1,25 @@
+* Synopsys DesignWare ABP UART
+
+Required properties:
+- compatible : "snps,dw-apb-uart"
+- reg : offset and length of the register set for the device.
+- interrupts : should contain uart interrupt.
+- clock-frequency : the input clock frequency for the UART.
+
+Optional properties:
+- reg-shift : quantity to shift the register offsets by.  If this property is
+  not present then the register offsets are not shifted.
+- reg-io-width : the size (in bytes) of the IO accesses that should be
+  performed on the device.  If this property is not present then single byte
+  accesses are used.
+
+Example:
+
+	uart@80230000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x80230000 0x100>;
+		clock-frequency = <3686400>;
+		interrupts = <10>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
diff --git a/Documentation/devicetree/bindings/serial/st-asc.txt b/Documentation/devicetree/bindings/serial/st-asc.txt
new file mode 100644
index 000000000000..75d877f5968f
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/st-asc.txt
@@ -0,0 +1,18 @@
+*st-asc(Serial Port)
+
+Required properties:
+- compatible : Should be "st,asc".
+- reg, reg-names, interrupts, interrupt-names	: Standard way to define device
+			resources with names. look in
+			Documentation/devicetree/bindings/resource-names.txt
+
+Optional properties:
+- st,hw-flow-ctrl	bool flag to enable hardware flow control.
+- st,force-m1		bool flat to force asc to be in Mode-1 recommeded
+			for high bit rates (above 19.2K)
+Example:
+serial@fe440000{
+    compatible    = "st,asc";
+    reg         = <0xfe440000 0x2c>;
+    interrupts     =  <0 209 0>;
+};
diff --git a/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt
new file mode 100644
index 000000000000..5feef1ef167d
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt
@@ -0,0 +1,17 @@
+VIA/Wondermedia VT8500 UART Controller
+-----------------------------------------------------
+
+Required properties:
+- compatible : "via,vt8500-uart"
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : UART interrupt
+- clocks : phandle to the uart source clock (usually a 24Mhz fixed clock)
+
+Example:
+
+	uart@d8210000 {
+		compatible = "via,vt8500-uart";
+		reg = <0xd8210000 0x1040>;
+		interrupts = <47>;
+		clocks = <&ref24>;
+	};