diff options
Diffstat (limited to 'Documentation/devicetree')
4 files changed, 96 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt new file mode 100644 index 000000000000..5edc310470b6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt @@ -0,0 +1,27 @@ +Hisilicon hi655x Power Management Integrated Circuit (PMIC) + +The hardware layout for access PMIC Hi655x from AP SoC Hi6220. +Between PMIC Hi655x and Hi6220, the physical signal channel is SSI. +We can use memory-mapped I/O to communicate. + ++----------------+ +-------------+ +| | | | +| Hi6220 | SSI bus | Hi655x | +| |-------------| | +| |(REGMAP_MMIO)| | ++----------------+ +-------------+ + +Required properties: +- compatible: Should be "hisilicon,hi655x-pmic" +- reg: Base address of PMIC on hi6220 soc +- interrupt-controller: Hi655x has internal IRQs (has own IRQ domain). +- pmic-gpios: The gpio used by PMIC irq. + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + reg = <0x0 0xf8000000 0x0 0x1000>; + interrupt-controller; + #interrupt-cells = <2>; + pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + } diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 8636f5ae97e5..9b4896c11716 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -39,6 +39,10 @@ Required Properties: Optional properties: +* resets: phandle + reset specifier pair, intended to represent hardware + reset signal present internally in some host controller IC designs. + See Documentation/devicetree/bindings/reset/reset.txt for details. + * clocks: from common clock binding: handle to biu and ciu clocks for the bus interface unit clock and the card interface unit clock. @@ -48,7 +52,7 @@ Optional properties: clock-frequency. It is an error to omit both the ciu clock and the clock-frequency. -* clock-frequency: should be the frequency (in Hz) of the ciu clock. If this +* clock-frequency: should be tke frequency (in Hz) of the ciu clock. If this is specified and the ciu clock is specified then we'll try to set the ciu clock to this at probe time. diff --git a/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt new file mode 100644 index 000000000000..09d3884e7cc2 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt @@ -0,0 +1,28 @@ +Hisilicon Hi655x Voltage regulators + +Note: +The hi655x regulator control is managed by hi655x Power IC. +So the node of this regulator must be child node of hi655x +PMIC node. + +The driver uses the regulator core framework, so please also +take the bindings of regulator.txt for reference. + +The valid names for regulators are: + +LDO2 LDO7 LDO10 LDO13 LDO14 LDO15 LDO17 LDO19 LDO21 LDO22 + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + ... + regulators { + ldo2: LDO2@a21 { + regulator-compatible = "LDO2_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + ... + } + } diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt new file mode 100644 index 000000000000..d0f91c557e27 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt @@ -0,0 +1,36 @@ +Hisilicon System Reset Controller +====================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +The reset controller registers are part of the system-ctl block on +hi6220 SoC. + +Required properties: +- compatible: should be one of the following: + "hisilicon,hi6220-sysctrl", "syscon" for peritheral reset, + "hisilicon,hi6220-pmctrl", "syscon" for media system reset. +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below + +Example: +sys_ctrl: sys_ctrl@f7030000 { + compatible = "hisilicon,hi6220-sysctrl", "syscon"; + reg = <0x0 0xf7030000 0x0 0x2000>; + #clock-cells = <1>; + #reset-cells = <1>; +}; + +Specifying reset lines connected to IP modules +============================================== +example: + + uart1: serial@..... { + ... + resets = <&sys_ctrl PERIPH_RSTEN3_UART1>; + ... + }; + +The index could be found in <dt-bindings/reset/hisi,hi6220-resets.h>. |