diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
13 files changed, 398 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 3a07a87fef20..6aca64f289b6 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -242,6 +242,23 @@ nodes to be present and contain the properties described below. Definition: Specifies the syscon node controlling the cpu core power domains. + - dynamic-power-coefficient + Usage: optional + Value type: <prop-encoded-array> + Definition: A u32 value that represents the running time dynamic + power coefficient in units of mW/MHz/uVolt^2. The + coefficient can either be calculated from power + measurements or derived by analysis. + + The dynamic power consumption of the CPU is + proportional to the square of the Voltage (V) and + the clock frequency (f). The coefficient is used to + calculate the dynamic power as below - + + Pdyn = dynamic-power-coefficient * V^2 * f + + where voltage is in uV, frequency is in MHz. + Example 1 (dual-cluster big.LITTLE system 32-bit): cpus { diff --git a/Documentation/devicetree/bindings/arm/firmware/linaro,optee-tz.txt b/Documentation/devicetree/bindings/arm/firmware/linaro,optee-tz.txt new file mode 100644 index 000000000000..d38834c67dff --- /dev/null +++ b/Documentation/devicetree/bindings/arm/firmware/linaro,optee-tz.txt @@ -0,0 +1,31 @@ +OP-TEE Device Tree Bindings + +OP-TEE is a piece of software using hardware features to provide a Trusted +Execution Environment. The security can be provided with ARM TrustZone, but +also by virtualization or a separate chip. + +We're using "linaro" as the first part of the compatible property for +the reference implementation maintained by Linaro. + +* OP-TEE based on ARM TrustZone required properties: + +- compatible : should contain "linaro,optee-tz" + +- method : The method of calling the OP-TEE Trusted OS. Permitted + values are: + + "smc" : SMC #0, with the register assignments specified + in drivers/tee/optee/optee_smc.h + + "hvc" : HVC #0, with the register assignments specified + in drivers/tee/optee/optee_smc.h + + + +Example: + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc"; + }; + }; diff --git a/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt new file mode 100644 index 000000000000..d270bfe4e4e0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt @@ -0,0 +1,72 @@ +Device-Tree bindings for DesignWare DSI Host Controller v1.20a driver + +A DSI Host Controller resides in the middle of display controller and external +HDMI converter or panel. + +Required properties: +- compatible: value should be "hisilicon,hi6220-dsi". +- reg: physical base address and length of dsi controller's registers. +- clocks: contains APB clock phandle + clock-specifier pair. +- clock-names: should be "pclk". +- ports: contains DSI controller input and output sub port. + The input port connects to ADE output port with the reg value "0". + The output port with the reg value "1", it could connect to panel or + any other bridge endpoints. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +A example of HiKey board hi6220 SoC and board specific DT entry: +Example: + +SoC specific: + dsi: dsi@f4107800 { + compatible = "hisilicon,hi6220-dsi"; + reg = <0x0 0xf4107800 0x0 0x100>; + clocks = <&media_ctrl HI6220_DSI_PCLK>; + clock-names = "pclk"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 0 for input port */ + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <&ade_out>; + }; + }; + }; + }; + + +Board specific: + &dsi { + status = "ok"; + + ports { + /* 1 for output port */ + port@1 { + reg = <1>; + + dsi_out0: endpoint@0 { + remote-endpoint = <&adv7533_in>; + }; + }; + }; + }; + + &i2c2 { + ... + + adv7533: adv7533@39 { + ... + + port { + adv7533_in: endpoint { + remote-endpoint = <&dsi_out0>; + }; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt new file mode 100644 index 000000000000..38dc9d60eef8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt @@ -0,0 +1,64 @@ +Device-Tree bindings for hisilicon ADE display controller driver + +ADE (Advanced Display Engine) is the display controller which grab image +data from memory, do composition, do post image processing, generate RGB +timing stream and transfer to DSI. + +Required properties: +- compatible: value should be "hisilicon,hi6220-ade". +- reg: physical base address and length of the ADE controller's registers. +- hisilicon,noc-syscon: ADE NOC QoS syscon. +- resets: The ADE reset controller node. +- interrupt: the ldi vblank interrupt number used. +- clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. +- clock-names: should contain: + "clk_ade_core" for the ADE core clock. + "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with + jpeg codec. + "clk_ade_pix" for the ADE pixel clok. +- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks' + phandle + clock-specifier pairs. +- assigned-clock-rates: clock rates, one for each entry in assigned-clocks. + The rate of "clk_ade_core" could be "360000000" or "180000000"; + The rate of "clk_codec_jpeg" could be or less than "1440000000". + These rate values could be configured according to performance and power + consumption. +- port: the output port. This contains one endpoint subnode, with its + remote-endpoint set to the phandle of the connected DSI input endpoint. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +Optional properties: +- dma-coherent: Present if dma operations are coherent. + + +A example of HiKey board hi6220 SoC specific DT entry: +Example: + + ade: ade@f4100000 { + compatible = "hisilicon,hi6220-ade"; + reg = <0x0 0xf4100000 0x0 0x7800>; + reg-names = "ade_base"; + hisilicon,noc-syscon = <&medianoc_ade>; + resets = <&media_ctrl MEDIA_ADE>; + interrupts = <0 115 4>; /* ldi interrupt */ + + clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>, + <&media_ctrl HI6220_ADE_PIX_SRC>; + /*clock name*/ + clock-names = "clk_ade_core", + "clk_codec_jpeg", + "clk_ade_pix"; + + assigned-clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>; + assigned-clock-rates = <360000000>, <288000000>; + dma-coherent; + + port { + ade_out: endpoint { + remote-endpoint = <&dsi_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mailbox/hisilicon,hi6220-mailbox.txt b/Documentation/devicetree/bindings/mailbox/hisilicon,hi6220-mailbox.txt new file mode 100644 index 000000000000..3dfb0b0ecd33 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/hisilicon,hi6220-mailbox.txt @@ -0,0 +1,57 @@ +Hisilicon Hi6220 Mailbox Driver +=============================== + +Hisilicon Hi6220 mailbox supports up to 32 channels. Each channel +is unidirectional with a maximum message size of 8 words. I/O is +performed using register access (there is no DMA) and the cell +raises an interrupt when messages are received. + +Mailbox Device Node: +==================== + +Required properties: +-------------------- +- compatible: Shall be "hisilicon,hi6220-mbox" +- reg: Contains the mailbox register address range (base + address and length); the first item is for IPC + registers, the second item is shared buffer for + slots. +- #mbox-cells Common mailbox binding property to identify the number + of cells required for the mailbox specifier. Should be 1. +- interrupts: Contains the interrupt information for the mailbox + device. The format is dependent on which interrupt + controller the SoCs use. + +Example: +-------- + + mailbox: mailbox@F7510000 { + #mbox-cells = <1>; + compatible = "hisilicon,hi6220-mbox"; + reg = <0x0 0xF7510000 0x0 0x1000>, /* IPC_S */ + <0x0 0x06DFF800 0x0 0x0800>; /* Mailbox */ + interrupt-parent = <&gic>; + interrupts = <0 94 4>; + }; + + +Mailbox client +=============== + +"mboxes" and the optional "mbox-names" (please see +Documentation/devicetree/bindings/mailbox/mailbox.txt for details). Each value +of the mboxes property should contain a phandle to the mailbox controller +device node and second argument is the channel index. It must be 0 (hardware +support only one channel). The equivalent "mbox-names" property value can be +used to give a name to the communication channel to be used by the client user. + +Example: +-------- + + stub_clock: stub_clock { + compatible = "hisilicon,hi6220-stub-clk"; + hisilicon,hi6220-clk-sram = <&sram>; + #clock-cells = <1>; + mbox-names = "mbox-tx"; + mboxes = <&mailbox 1>; + }; diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt new file mode 100644 index 000000000000..5edc310470b6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt @@ -0,0 +1,27 @@ +Hisilicon hi655x Power Management Integrated Circuit (PMIC) + +The hardware layout for access PMIC Hi655x from AP SoC Hi6220. +Between PMIC Hi655x and Hi6220, the physical signal channel is SSI. +We can use memory-mapped I/O to communicate. + ++----------------+ +-------------+ +| | | | +| Hi6220 | SSI bus | Hi655x | +| |-------------| | +| |(REGMAP_MMIO)| | ++----------------+ +-------------+ + +Required properties: +- compatible: Should be "hisilicon,hi655x-pmic" +- reg: Base address of PMIC on hi6220 soc +- interrupt-controller: Hi655x has internal IRQs (has own IRQ domain). +- pmic-gpios: The gpio used by PMIC irq. + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + reg = <0x0 0xf8000000 0x0 0x1000>; + interrupt-controller; + #interrupt-cells = <2>; + pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + } diff --git a/Documentation/devicetree/bindings/misc/ramoops.txt b/Documentation/devicetree/bindings/misc/ramoops.txt new file mode 100644 index 000000000000..5a475fae4aab --- /dev/null +++ b/Documentation/devicetree/bindings/misc/ramoops.txt @@ -0,0 +1,43 @@ +Ramoops oops/panic logger +========================= + +ramoops provides persistent RAM storage for oops and panics, so they can be +recovered after a reboot. + +Parts of this storage may be set aside for other persistent log buffers, such +as kernel log messages, or for optional ECC error-correction data. The total +size of these optional buffers must fit in the reserved region. + +Any remaining space will be used for a circular buffer of oops and panic +records. These records have a configurable size, with a size of 0 indicating +that they should be disabled. + + +Required properties: + +- compatible: must be "ramoops" + +- memory-region: phandle to a region of memory that is preserved between reboots + + +Optional properties: + +- ecc-size: enables ECC support and specifies ECC buffer size in bytes + (defaults to no ECC) + +- record-size: maximum size in bytes of each dump done on oops/panic + (defaults to 0) + +- console-size: size in bytes of log buffer reserved for kernel messages + (defaults to 0) + +- ftrace-size: size in bytes of log buffer reserved for function tracing and + profiling (defaults to 0) + +- pmsg-size: size in bytes of log buffer reserved for userspace messages + (defaults to 0) + +- unbuffered: if present, use unbuffered mappings to map the reserved region + (defaults to buffered mappings) + +- no-dump-oops: if present, only dump panics (defaults to panics and oops) diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 8636f5ae97e5..9b4896c11716 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -39,6 +39,10 @@ Required Properties: Optional properties: +* resets: phandle + reset specifier pair, intended to represent hardware + reset signal present internally in some host controller IC designs. + See Documentation/devicetree/bindings/reset/reset.txt for details. + * clocks: from common clock binding: handle to biu and ciu clocks for the bus interface unit clock and the card interface unit clock. @@ -48,7 +52,7 @@ Optional properties: clock-frequency. It is an error to omit both the ciu clock and the clock-frequency. -* clock-frequency: should be the frequency (in Hz) of the ciu clock. If this +* clock-frequency: should be tke frequency (in Hz) of the ciu clock. If this is specified and the ciu clock is specified then we'll try to set the ciu clock to this at probe time. diff --git a/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt b/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt new file mode 100644 index 000000000000..f17a56e2152f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt @@ -0,0 +1,16 @@ +Hisilicon hi6220 usb PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hi6220-usb-phy" +- #phy-cells: must be 0 +- hisilicon,peripheral-syscon: phandle of syscon used to control phy. +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usb_phy: usbphy { + compatible = "hisilicon,hi6220-usb-phy"; + #phy-cells = <0>; + phy-supply = <&fixed_5v_hub>; + hisilicon,peripheral-syscon = <&sys_ctrl>; + }; diff --git a/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt new file mode 100644 index 000000000000..09d3884e7cc2 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt @@ -0,0 +1,28 @@ +Hisilicon Hi655x Voltage regulators + +Note: +The hi655x regulator control is managed by hi655x Power IC. +So the node of this regulator must be child node of hi655x +PMIC node. + +The driver uses the regulator core framework, so please also +take the bindings of regulator.txt for reference. + +The valid names for regulators are: + +LDO2 LDO7 LDO10 LDO13 LDO14 LDO15 LDO17 LDO19 LDO21 LDO22 + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + ... + regulators { + ldo2: LDO2@a21 { + regulator-compatible = "LDO2_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + ... + } + } diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt new file mode 100644 index 000000000000..d0f91c557e27 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt @@ -0,0 +1,36 @@ +Hisilicon System Reset Controller +====================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +The reset controller registers are part of the system-ctl block on +hi6220 SoC. + +Required properties: +- compatible: should be one of the following: + "hisilicon,hi6220-sysctrl", "syscon" for peritheral reset, + "hisilicon,hi6220-pmctrl", "syscon" for media system reset. +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below + +Example: +sys_ctrl: sys_ctrl@f7030000 { + compatible = "hisilicon,hi6220-sysctrl", "syscon"; + reg = <0x0 0xf7030000 0x0 0x2000>; + #clock-cells = <1>; + #reset-cells = <1>; +}; + +Specifying reset lines connected to IP modules +============================================== +example: + + uart1: serial@..... { + ... + resets = <&sys_ctrl PERIPH_RSTEN3_UART1>; + ... + }; + +The index could be found in <dt-bindings/reset/hisi,hi6220-resets.h>. diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index fd132cbee70e..221368207ca4 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -4,6 +4,7 @@ Platform DesignWare HS OTG USB 2.0 controller Required properties: - compatible : One of: - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC. + - hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC. - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 98dc17507a84..7004fa94c368 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -128,6 +128,7 @@ lacie LaCie lantiq Lantiq Semiconductor lenovo Lenovo Group Ltd. lg LG Corporation +linaro Linaro Limited linux Linux-specific binding lsi LSI Corp. (LSI Logic) lltc Linear Technology Corporation |