/* * pci.h * * PCI defines and function prototypes * Copyright 1994, Drew Eckhardt * Copyright 1997--1999 Martin Mares * * For more information, please consult the following manuals (look at * http://www.pcisig.com/ for how to get them): * * PCI BIOS Specification * PCI Local Bus Specification * PCI to PCI Bridge Specification * PCI System Design Guide */ #ifndef LINUX_PCI_H #define LINUX_PCI_H #include /* * Under PCI, each device has 256 bytes of configuration address space, * of which the first 64 bytes are standardized as follows: */ #define PCI_VENDOR_ID 0x00 /* 16 bits */ #define PCI_DEVICE_ID 0x02 /* 16 bits */ #define PCI_COMMAND 0x04 /* 16 bits */ #define PCI_COMMAND_IO 0x1 /* Enable response in I/O space */ #define PCI_COMMAND_MEMORY 0x2 /* Enable response in Memory space */ #define PCI_COMMAND_MASTER 0x4 /* Enable bus mastering */ #define PCI_COMMAND_SPECIAL 0x8 /* Enable response to special cycles */ #define PCI_COMMAND_INVALIDATE 0x10 /* Use memory write and invalidate */ #define PCI_COMMAND_VGA_PALETTE 0x20 /* Enable palette snooping */ #define PCI_COMMAND_PARITY 0x40 /* Enable parity checking */ #define PCI_COMMAND_WAIT 0x80 /* Enable address/data stepping */ #define PCI_COMMAND_SERR 0x100 /* Enable SERR */ #define PCI_COMMAND_FAST_BACK 0x200 /* Enable back-to-back writes */ #define PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */ #define PCI_STATUS 0x06 /* 16 bits */ #define PCI_STATUS_CAP_LIST 0x10 /* Support Capability List */ #define PCI_STATUS_66MHZ 0x20 /* Support 66 Mhz PCI 2.1 bus */ #define PCI_STATUS_UDF 0x40 /* Support User Definable Features [obsolete] */ #define PCI_STATUS_FAST_BACK 0x80 /* Accept fast-back to back */ #define PCI_STATUS_PARITY 0x100 /* Detected parity error */ #define PCI_STATUS_DEVSEL_MASK 0x600 /* DEVSEL timing */ #define PCI_STATUS_DEVSEL_FAST 0x000 #define PCI_STATUS_DEVSEL_MEDIUM 0x200 #define PCI_STATUS_DEVSEL_SLOW 0x400 #define PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */ #define PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */ #define PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */ #define PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */ #define PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */ #define PCI_CLASS_REVISION 0x08 /* High 24 bits are class, low 8 revision */ #define PCI_REVISION_ID 0x08 /* Revision ID */ #define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */ #define PCI_CLASS_DEVICE 0x0a /* Device class */ #define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */ #define PCI_LATENCY_TIMER 0x0d /* 8 bits */ #define PCI_HEADER_TYPE 0x0e /* 8 bits */ #define PCI_HEADER_TYPE_NORMAL 0 #define PCI_HEADER_TYPE_BRIDGE 1 #define PCI_HEADER_TYPE_CARDBUS 2 #define PCI_BIST 0x0f /* 8 bits */ #define PCI_BIST_CODE_MASK 0x0f /* Return result */ #define PCI_BIST_START 0x40 /* 1 to start BIST, 2 secs or less */ #define PCI_BIST_CAPABLE 0x80 /* 1 if BIST capable */ /* * Base addresses specify locations in memory or I/O space. * Decoded size can be determined by writing a value of * 0xffffffff to the register, and reading it back. Only * 1 bits are decoded. */ #define PCI_BASE_ADDRESS_0 0x10 /* 32 bits */ #define PCI_BASE_ADDRESS_1 0x14 /* 32 bits [htype 0,1 only] */ #define PCI_BASE_ADDRESS_2 0x18 /* 32 bits [htype 0 only] */ #define PCI_BASE_ADDRESS_3 0x1c /* 32 bits */ #define PCI_BASE_ADDRESS_4 0x20 /* 32 bits */ #define PCI_BASE_ADDRESS_5 0x24 /* 32 bits */ #define PCI_BASE_ADDRESS_SPACE 0x01 /* 0 = memory, 1 = I/O */ #define PCI_BASE_ADDRESS_SPACE_IO 0x01 #define PCI_BASE_ADDRESS_SPACE_MEMORY 0x00 #define PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06 #define PCI_BASE_ADDRESS_MEM_TYPE_32 0x00 /* 32 bit address */ #define PCI_BASE_ADDRESS_MEM_TYPE_1M 0x02 /* Below 1M [obsolete] */ #define PCI_BASE_ADDRESS_MEM_TYPE_64 0x04 /* 64 bit address */ #define PCI_BASE_ADDRESS_MEM_PREFETCH 0x08 /* prefetchable? */ #define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL) #define PCI_BASE_ADDRESS_IO_MASK (~0x03UL) /* bit 1 is reserved if address_space = 1 */ /* Header type 0 (normal devices) */ #define PCI_CARDBUS_CIS 0x28 #define PCI_SUBSYSTEM_VENDOR_ID 0x2c #define PCI_SUBSYSTEM_ID 0x2e #define PCI_ROM_ADDRESS 0x30 /* Bits 31..11 are address, 10..1 reserved */ #define PCI_ROM_ADDRESS_ENABLE 0x01 #define PCI_ROM_ADDRESS_MASK (~0x7ffUL) #define PCI_CAPABILITY_LIST 0x34 /* Offset of first capability list entry */ /* 0x35-0x3b are reserved */ #define PCI_INTERRUPT_LINE 0x3c /* 8 bits */ #define PCI_INTERRUPT_PIN 0x3d /* 8 bits */ #define PCI_MIN_GNT 0x3e /* 8 bits */ #define PCI_MAX_LAT 0x3f /* 8 bits */ /* Header type 1 (PCI-to-PCI bridges) */ #define PCI_PRIMARY_BUS 0x18 /* Primary bus number */ #define PCI_SECONDARY_BUS 0x19 /* Secondary bus number */ #define PCI_SUBORDINATE_BUS 0x1a /* Highest bus number behind the bridge */ #define PCI_SEC_LATENCY_TIMER 0x1b /* Latency timer for secondary interface */ #define PCI_IO_BASE 0x1c /* I/O range behind the bridge */ #define PCI_IO_LIMIT 0x1d #define PCI_IO_RANGE_TYPE_MASK 0x0fUL /* I/O bridging type */ #define PCI_IO_RANGE_TYPE_16 0x00 #define PCI_IO_RANGE_TYPE_32 0x01 #define PCI_IO_RANGE_MASK (~0x0fUL) #define PCI_SEC_STATUS 0x1e /* Secondary status register, only bit 14 used */ #define PCI_MEMORY_BASE 0x20 /* Memory range behind */ #define PCI_MEMORY_LIMIT 0x22 #define PCI_MEMORY_RANGE_TYPE_MASK 0x0fUL #define PCI_MEMORY_RANGE_MASK (~0x0fUL) #define PCI_PREF_MEMORY_BASE 0x24 /* Prefetchable memory range behind */ #define PCI_PREF_MEMORY_LIMIT 0x26 #define PCI_PREF_RANGE_TYPE_MASK 0x0fUL #define PCI_PREF_RANGE_TYPE_32 0x00 #define PCI_PREF_RANGE_TYPE_64 0x01 #define PCI_PREF_RANGE_MASK (~0x0fUL) #define PCI_PREF_BASE_UPPER32 0x28 /* Upper half of prefetchable memory range */ #define PCI_PREF_LIMIT_UPPER32 0x2c #define PCI_IO_BASE_UPPER16 0x30 /* Upper half of I/O addresses */ #define PCI_IO_LIMIT_UPPER16 0x32 /* 0x34 same as for htype 0 */ /* 0x35-0x3b is reserved */ #define PCI_ROM_ADDRESS1 0x38 /* Same as PCI_ROM_ADDRESS, but for htype 1 */ /* 0x3c-0x3d are same as for htype 0 */ #define PCI_BRIDGE_CONTROL 0x3e #define PCI_BRIDGE_CTL_PARITY 0x01 /* Enable parity detection on secondary interface */ #define PCI_BRIDGE_CTL_SERR 0x02 /* The same for SERR forwarding */ #define PCI_BRIDGE_CTL_NO_ISA 0x04 /* Disable bridging of ISA ports */ #define PCI_BRIDGE_CTL_VGA 0x08 /* Forward VGA addresses */ #define PCI_BRIDGE_CTL_MASTER_ABORT 0x20 /* Report master aborts */ #define PCI_BRIDGE_CTL_BUS_RESET 0x40 /* Secondary bus reset */ #define PCI_BRIDGE_CTL_FAST_BACK 0x80 /* Fast Back2Back enabled on secondary interface */ /* Header type 2 (CardBus bridges) */ #define PCI_CB_CAPABILITY_LIST 0x14 /* 0x15 reserved */ #define PCI_CB_SEC_STATUS 0x16 /* Secondary status */ #define PCI_CB_PRIMARY_BUS 0x18 /* PCI bus number */ #define PCI_CB_CARD_BUS 0x19 /* CardBus bus number */ #define PCI_CB_SUBORDINATE_BUS 0x1a /* Subordinate bus number */ #define PCI_CB_LATENCY_TIMER 0x1b /* CardBus latency timer */ #define PCI_CB_MEMORY_BASE_0 0x1c #define PCI_CB_MEMORY_LIMIT_0 0x20 #define PCI_CB_MEMORY_BASE_1 0x24 #define PCI_CB_MEMORY_LIMIT_1 0x28 #define PCI_CB_IO_BASE_0 0x2c #define PCI_CB_IO_BASE_0_HI 0x2e #define PCI_CB_IO_LIMIT_0 0x30 #define PCI_CB_IO_LIMIT_0_HI 0x32 #define PCI_CB_IO_BASE_1 0x34 #define PCI_CB_IO_BASE_1_HI 0x36 #define PCI_CB_IO_LIMIT_1 0x38 #define PCI_CB_IO_LIMIT_1_HI 0x3a #define PCI_CB_IO_RANGE_MASK (~0x03UL) /* 0x3c-0x3d are same as for htype 0 */ #define PCI_CB_BRIDGE_CONTROL 0x3e #define PCI_CB_BRIDGE_CTL_PARITY 0x01 /* Similar to standard bridge control register */ #define PCI_CB_BRIDGE_CTL_SERR 0x02 #define PCI_CB_BRIDGE_CTL_ISA 0x04 #define PCI_CB_BRIDGE_CTL_VGA 0x08 #define PCI_CB_BRIDGE_CTL_MASTER_ABORT 0x20 #define PCI_CB_BRIDGE_CTL_CB_RESET 0x40 /* CardBus reset */ #define PCI_CB_BRIDGE_CTL_16BIT_INT 0x80 /* Enable interrupt for 16-bit cards */ #define PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100 /* Prefetch enable for both memory regions */ #define PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200 #define PCI_CB_BRIDGE_CTL_POST_WRITES 0x400 #define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40 #define PCI_CB_SUBSYSTEM_ID 0x42 #define PCI_CB_LEGACY_MODE_BASE 0x44 /* 16-bit PC Card legacy mode base address (ExCa) */ /* 0x48-0x7f reserved */ /* Capability lists */ #define PCI_CAP_LIST_ID 0 /* Capability ID */ #define PCI_CAP_ID_PM 0x01 /* Power Management */ #define PCI_CAP_ID_AGP 0x02 /* Accelerated Graphics Port */ #define PCI_CAP_ID_VPD 0x03 /* Vital Product Data */ #define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */ #define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */ #define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */ #define PCI_CAP_ID_PCIX 0x07 /* PCI-X */ #define PCI_CAP_ID_SHPC 0x0C /* PCI Standard Hot-Plug Controller */ #define PCI_CAP_ID_EXP 0x10 /* PCI Express */ #define PCI_CAP_ID_MSIX 0x11 /* MSI-X */ #define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */ #define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */ #define PCI_CAP_SIZEOF 4 /* Power Management Registers */ #define PCI_PM_PMC 2 /* PM Capabilities Register */ #define PCI_PM_CAP_VER_MASK 0x0007 /* Version */ #define PCI_PM_CAP_PME_CLOCK 0x0008 /* PME clock required */ #define PCI_PM_CAP_RESERVED 0x0010 /* Reserved field */ #define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization */ #define PCI_PM_CAP_AUX_POWER 0x01C0 /* Auxilliary power support mask */ #define PCI_PM_CAP_D1 0x0200 /* D1 power state support */ #define PCI_PM_CAP_D2 0x0400 /* D2 power state support */ #define PCI_PM_CAP_PME 0x0800 /* PME pin supported */ #define PCI_PM_CAP_PME_MASK 0xF800 /* PME Mask of all supported states */ #define PCI_PM_CAP_PME_D0 0x0800 /* PME# from D0 */ #define PCI_PM_CAP_PME_D1 0x1000 /* PME# from D1 */ #define PCI_PM_CAP_PME_D2 0x2000 /* PME# from D2 */ #define PCI_PM_CAP_PME_D3 0x4000 /* PME# from D3 (hot) */ #define PCI_PM_CAP_PME_D3cold 0x8000 /* PME# from D3 (cold) */ #define PCI_PM_CTRL 4 /* PM control and status register */ #define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */ #define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */ #define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* Data select (??) */ #define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* Data scale (??) */ #define PCI_PM_CTRL_PME_STATUS 0x8000 /* PME pin status */ #define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions (??) */ #define PCI_PM_PPB_B2_B3 0x40 /* Stop clock when in D3hot (??) */ #define PCI_PM_BPCC_ENABLE 0x80 /* Bus power/clock control enable (??) */ #define PCI_PM_DATA_REGISTER 7 /* (??) */ #define PCI_PM_SIZEOF 8 /* AGP registers */ #define PCI_AGP_VERSION 2 /* BCD version number */ #define PCI_AGP_RFU 3 /* Rest of capability flags */ #define PCI_AGP_STATUS 4 /* Status register */ #define PCI_AGP_STATUS_RQ_MASK 0xff000000 /* Maximum number of requests - 1 */ #define PCI_AGP_STATUS_SBA 0x0200 /* Sideband addressing supported */ #define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing supported */ #define PCI_AGP_STATUS_FW 0x0010 /* FW transfers supported */ #define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported */ #define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported */ #define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported */ #define PCI_AGP_COMMAND 8 /* Control register */ #define PCI_AGP_COMMAND_RQ_MASK 0xff000000 /* Master: Maximum number of requests */ #define PCI_AGP_COMMAND_SBA 0x0200 /* Sideband addressing enabled */ #define PCI_AGP_COMMAND_AGP 0x0100 /* Allow processing of AGP transactions */ #define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow processing of 64-bit addresses */ #define PCI_AGP_COMMAND_FW 0x0010 /* Force FW transfers */ #define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate */ #define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 2x rate */ #define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 1x rate */ #define PCI_AGP_SIZEOF 12 /* Vital Product Data */ #define PCI_VPD_ADDR 2 /* Address to access (15 bits!) */ #define PCI_VPD_ADDR_MASK 0x7fff /* Address mask */ #define PCI_VPD_ADDR_F 0x8000 /* Write 0, 1 indicates completion */ #define PCI_VPD_DATA 4 /* 32-bits of data returned here */ /* Slot Identification */ #define PCI_SID_ESR 2 /* Expansion Slot Register */ #define PCI_SID_ESR_NSLOTS 0x1f /* Number of expansion slots available */ #define PCI_SID_ESR_FIC 0x20 /* First In Chassis Flag */ #define PCI_SID_CHASSIS_NR 3 /* Chassis Number */ /* Message Signalled Interrupts registers */ #define PCI_MSI_FLAGS 2 /* Various flags */ #define PCI_MSI_FLAGS_64BIT 0x80 /* 64-bit addresses allowed */ #define PCI_MSI_FLAGS_QSIZE 0x70 /* Message queue size configured */ #define PCI_MSI_FLAGS_QMASK 0x0e /* Maximum queue size available */ #define PCI_MSI_FLAGS_ENABLE 0x01 /* MSI feature enabled */ #define PCI_MSI_FLAGS_MASKBIT 0x100 /* 64-bit mask bits allowed */ #define PCI_MSI_RFU 3 /* Rest of capability flags */ #define PCI_MSI_ADDRESS_LO 4 /* Lower 32 bits */ #define PCI_MSI_ADDRESS_HI 8 /* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */ #define PCI_MSI_DATA_32 8 /* 16 bits of data for 32-bit devices */ #define PCI_MSI_DATA_64 12 /* 16 bits of data for 64-bit devices */ #define PCI_MSI_MASK_BIT 16 /* Mask bits register */ /* CompactPCI Hotswap Register */ #define PCI_CHSWP_CSR 2 /* Control and Status Register */ #define PCI_CHSWP_DHA 0x01 /* Device Hiding Arm */ #define PCI_CHSWP_EIM 0x02 /* ENUM# Signal Mask */ #define PCI_CHSWP_PIE 0x04 /* Pending Insert or Extract */ #define PCI_CHSWP_LOO 0x08 /* LED On / Off */ #define PCI_CHSWP_PI 0x30 /* Programming Interface */ #define PCI_CHSWP_EXT 0x40 /* ENUM# status - extraction */ #define PCI_CHSWP_INS 0x80 /* ENUM# status - insertion */ /* PCI-X registers */ #define PCI_X_CMD 2 /* Modes & Features */ #define PCI_X_CMD_DPERR_E 0x0001 /* Data Parity Error Recovery Enable */ #define PCI_X_CMD_ERO 0x0002 /* Enable Relaxed Ordering */ #define PCI_X_CMD_MAX_READ 0x000c /* Max Memory Read Byte Count */ #define PCI_X_CMD_MAX_SPLIT 0x0070 /* Max Outstanding Split Transactions */ #define PCI_X_CMD_VERSION(x) (((x) >> 12) & 3) /* Version */ #define PCI_X_STATUS 4 /* PCI-X capabilities */ #define PCI_X_STATUS_DEVFN 0x000000ff /* A copy of devfn */ #define PCI_X_STATUS_BUS 0x0000ff00 /* A copy of bus nr */ #define PCI_X_STATUS_64BIT 0x00010000 /* 64-bit device */ #define PCI_X_STATUS_133MHZ 0x00020000 /* 133 MHz capable */ #define PCI_X_STATUS_SPL_DISC 0x00040000 /* Split Completion Discarded */ #define PCI_X_STATUS_UNX_SPL 0x00080000 /* Unexpected Split Completion */ #define PCI_X_STATUS_COMPLEX 0x00100000 /* Device Complexity */ #define PCI_X_STATUS_MAX_READ 0x00600000 /* Designed Max Memory Read Count */ #define PCI_X_STATUS_MAX_SPLIT 0x03800000 /* Designed Max Outstanding Split Transactions */ #define PCI_X_STATUS_MAX_CUM 0x1c000000 /* Designed Max Cumulative Read Size */ #define PCI_X_STATUS_SPL_ERR 0x20000000 /* Rcvd Split Completion Error Msg */ #define PCI_X_STATUS_266MHZ 0x40000000 /* 266 MHz capable */ #define PCI_X_STATUS_533MHZ 0x80000000 /* 533 MHz capable */ /* PCI Express capability registers */ #define PCI_EXP_FLAGS 2 /* Capabilities register */ #define PCI_EXP_FLAGS_VERS 0x000f /* Capability version */ #define PCI_EXP_FLAGS_TYPE 0x00f0 /* Device/Port type */ #define PCI_EXP_TYPE_ENDPOINT 0x0 /* Express Endpoint */ #define PCI_EXP_TYPE_LEG_END 0x1 /* Legacy Endpoint */ #define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */ #define PCI_EXP_TYPE_UPSTREAM 0x5 /* Upstream Port */ #define PCI_EXP_TYPE_DOWNSTREAM 0x6 /* Downstream Port */ #define PCI_EXP_TYPE_PCI_BRIDGE 0x7 /* PCI/PCI-X Bridge */ #define PCI_EXP_FLAGS_SLOT 0x0100 /* Slot implemented */ #define PCI_EXP_FLAGS_IRQ 0x3e00 /* Interrupt message number */ #define PCI_EXP_DEVCAP 4 /* Device capabilities */ #define PCI_EXP_DEVCAP_PAYLOAD 0x07 /* Max_Payload_Size */ #define PCI_EXP_DEVCAP_PHANTOM 0x18 /* Phantom functions */ #define PCI_EXP_DEVCAP_EXT_TAG 0x20 /* Extended tags */ #define PCI_EXP_DEVCAP_L0S 0x1c0 /* L0s Acceptable Latency */ #define PCI_EXP_DEVCAP_L1 0xe00 /* L1 Acceptable Latency */ #define PCI_EXP_DEVCAP_ATN_BUT 0x1000 /* Attention Button Present */ #define PCI_EXP_DEVCAP_ATN_IND 0x2000 /* Attention Indicator Present */ #define PCI_EXP_DEVCAP_PWR_IND 0x4000 /* Power Indicator Present */ #define PCI_EXP_DEVCAP_PWR_VAL 0x3fc0000 /* Slot Power Limit Value */ #define PCI_EXP_DEVCAP_PWR_SCL 0xc000000 /* Slot Power Limit Scale */ #define PCI_EXP_DEVCTL 8 /* Device Control */ #define PCI_EXP_DEVCTL_CERE 0x0001 /* Correctable Error Reporting En. */ #define PCI_EXP_DEVCTL_NFERE 0x0002 /* Non-Fatal Error Reporting Enable */ #define PCI_EXP_DEVCTL_FERE 0x0004 /* Fatal Error Reporting Enable */ #define PCI_EXP_DEVCTL_URRE 0x0008 /* Unsupported Request Reporting En. */ #define PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */ #define PCI_EXP_DEVCTL_PAYLOAD 0x00e0 /* Max_Payload_Size */ #define PCI_EXP_DEVCTL_EXT_TAG 0x0100 /* Extended Tag Field Enable */ #define PCI_EXP_DEVCTL_PHANTOM 0x0200 /* Phantom Functions Enable */ #define PCI_EXP_DEVCTL_AUX_PME 0x0400 /* Auxiliary Power PM Enable */ #define PCI_EXP_DEVCTL_NOSNOOP_EN 0x0800 /* Enable No Snoop */ #define PCI_EXP_DEVCTL_READRQ 0x7000 /* Max_Read_Request_Size */ #define PCI_EXP_DEVSTA 10 /* Device Status */ #define PCI_EXP_DEVSTA_CED 0x01 /* Correctable Error Detected */ #define PCI_EXP_DEVSTA_NFED 0x02 /* Non-Fatal Error Detected */ #define PCI_EXP_DEVSTA_FED 0x04 /* Fatal Error Detected */ #define PCI_EXP_DEVSTA_URD 0x08 /* Unsupported Request Detected */ #define PCI_EXP_DEVSTA_AUXPD 0x10 /* AUX Power Detected */ #define PCI_EXP_DEVSTA_TRPND 0x20 /* Transactions Pending */ #define PCI_EXP_LNKCAP 12 /* Link Capabilities */ #define PCI_EXP_LNKCTL 16 /* Link Control */ #define PCI_EXP_LNKSTA 18 /* Link Status */ #define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ #define PCI_EXP_SLTCTL 24 /* Slot Control */ #define PCI_EXP_SLTSTA 26 /* Slot Status */ #define PCI_EXP_RTCTL 28 /* Root Control */ #define PCI_EXP_RTCTL_SECEE 0x01 /* System Error on Correctable Error */ #define PCI_EXP_RTCTL_SENFEE 0x02 /* System Error on Non-Fatal Error */ #define PCI_EXP_RTCTL_SEFEE 0x04 /* System Error on Fatal Error */ #define PCI_EXP_RTCTL_PMEIE 0x08 /* PME Interrupt Enable */ #define PCI_EXP_RTCTL_CRSSVE 0x10 /* CRS Software Visibility Enable */ #define PCI_EXP_RTCAP 30 /* Root Capabilities */ #define PCI_EXP_RTSTA 32 /* Root Status */ /* Extended Capabilities (PCI-X 2.0 and Express) */ #define PCI_EXT_CAP_ID(header) (header & 0x0000ffff) #define PCI_EXT_CAP_VER(header) ((header >> 16) & 0xf) #define PCI_EXT_CAP_NEXT(header) ((header >> 20) & 0xffc) #define PCI_EXT_CAP_ID_ERR 1 #define PCI_EXT_CAP_ID_VC 2 #define PCI_EXT_CAP_ID_DSN 3 #define PCI_EXT_CAP_ID_PWR 4 /* Advanced Error Reporting */ #define PCI_ERR_UNCOR_STATUS 4 /* Uncorrectable Error Status */ #define PCI_ERR_UNC_TRAIN 0x00000001 /* Training */ #define PCI_ERR_UNC_DLP 0x00000010 /* Data Link Protocol */ #define PCI_ERR_UNC_POISON_TLP 0x00001000 /* Poisoned TLP */ #define PCI_ERR_UNC_FCP 0x00002000 /* Flow Control Protocol */ #define PCI_ERR_UNC_COMP_TIME 0x00004000 /* Completion Timeout */ #define PCI_ERR_UNC_COMP_ABORT 0x00008000 /* Completer Abort */ #define PCI_ERR_UNC_UNX_COMP 0x00010000 /* Unexpected Completion */ #define PCI_ERR_UNC_RX_OVER 0x00020000 /* Receiver Overflow */ #define PCI_ERR_UNC_MALF_TLP 0x00040000 /* Malformed TLP */ #define PCI_ERR_UNC_ECRC 0x00080000 /* ECRC Error Status */ #define PCI_ERR_UNC_UNSUP 0x00100000 /* Unsupported Request */ #define PCI_ERR_UNCOR_MASK 8 /* Uncorrectable Error Mask */ /* Same bits as above */ #define PCI_ERR_UNCOR_SEVER 12 /* Uncorrectable Error Severity */ /* Same bits as above */ #define PCI_ERR_COR_STATUS 16 /* Correctable Error Status */ #define PCI_ERR_COR_RCVR 0x00000001 /* Receiver Error Status */ #define PCI_ERR_COR_BAD_TLP 0x00000040 /* Bad TLP Status */ #define PCI_ERR_COR_BAD_DLLP 0x00000080 /* Bad DLLP Status */ #define PCI_ERR_COR_REP_ROLL 0x00000100 /* REPLAY_NUM Rollover */ #define PCI_ERR_COR_REP_TIMER 0x00001000 /* Replay Timer Timeout */ #define PCI_ERR_COR_MASK 20 /* Correctable Error Mask */ /* Same bits as above */ #define PCI_ERR_CAP 24 /* Advanced Error Capabilities */ #define PCI_ERR_CAP_FEP(x) ((x) & 31) /* First Error Pointer */ #define PCI_ERR_CAP_ECRC_GENC 0x00000020 /* ECRC Generation Capable */ #define PCI_ERR_CAP_ECRC_GENE 0x00000040 /* ECRC Generation Enable */ #define PCI_ERR_CAP_ECRC_CHKC 0x00000080 /* ECRC Check Capable */ #define PCI_ERR_CAP_ECRC_CHKE 0x00000100 /* ECRC Check Enable */ #define PCI_ERR_HEADER_LOG 28 /* Header Log Register (16 bytes) */ #define PCI_ERR_ROOT_COMMAND 44 /* Root Error Command */ #define PCI_ERR_ROOT_STATUS 48 #define PCI_ERR_ROOT_COR_SRC 52 #define PCI_ERR_ROOT_SRC 54 /* Virtual Channel */ #define PCI_VC_PORT_REG1 4 #define PCI_VC_PORT_REG2 8 #define PCI_VC_PORT_CTRL 12 #define PCI_VC_PORT_STATUS 14 #define PCI_VC_RES_CAP 16 #define PCI_VC_RES_CTRL 20 #define PCI_VC_RES_STATUS 26 /* Power Budgeting */ #define PCI_PWR_DSR 4 /* Data Select Register */ #define PCI_PWR_DATA 8 /* Data Register */ #define PCI_PWR_DATA_BASE(x) ((x) & 0xff) /* Base Power */ #define PCI_PWR_DATA_SCALE(x) (((x) >> 8) & 3) /* Data Scale */ #define PCI_PWR_DATA_PM_SUB(x) (((x) >> 10) & 7) /* PM Sub State */ #define PCI_PWR_DATA_PM_STATE(x) (((x) >> 13) & 3) /* PM State */ #define PCI_PWR_DATA_TYPE(x) (((x) >> 15) & 7) /* Type */ #define PCI_PWR_DATA_RAIL(x) (((x) >> 18) & 7) /* Power Rail */ #define PCI_PWR_CAP 12 /* Capability */ #define PCI_PWR_CAP_BUDGET(x) ((x) & 1) /* Included in system budget */ /* Include the ID list */ #include /* * The PCI interface treats multi-function devices as independent * devices. The slot/function address of each device is encoded * in a single byte as follows: * * 7:3 = slot * 2:0 = function */ #define PCI_DEVFN(slot,func) ((((slot) & 0x1f) << 3) | ((func) & 0x07)) #define PCI_SLOT(devfn) (((devfn) >> 3) & 0x1f) #define PCI_FUNC(devfn) ((devfn) & 0x07) /* Ioctls for /proc/bus/pci/X/Y nodes. */ #define PCIIOC_BASE ('P' << 24 | 'C' << 16 | 'I' << 8) #define PCIIOC_CONTROLLER (PCIIOC_BASE | 0x00) /* Get controller for PCI device. */ #define PCIIOC_MMAP_IS_IO (PCIIOC_BASE | 0x01) /* Set mmap state to I/O space. */ #define PCIIOC_MMAP_IS_MEM (PCIIOC_BASE | 0x02) /* Set mmap state to MEM space. */ #define PCIIOC_WRITE_COMBINE (PCIIOC_BASE | 0x03) /* Enable/disable write-combining. */ #ifdef __KERNEL__ #include #include #include #include #include #include /* File state for mmap()s on /proc/bus/pci/X/Y */ enum pci_mmap_state { pci_mmap_io, pci_mmap_mem }; /* This defines the direction arg to the DMA mapping routines. */ #define PCI_DMA_BIDIRECTIONAL 0 #define PCI_DMA_TODEVICE 1 #define PCI_DMA_FROMDEVICE 2 #define PCI_DMA_NONE 3 #define DEVICE_COUNT_COMPATIBLE 4 #define DEVICE_COUNT_RESOURCE 12 typedef int __bitwise pci_power_t; #define PCI_D0 ((pci_power_t __force) 0) #define PCI_D1 ((pci_power_t __force) 1) #define PCI_D2 ((pci_power_t __force) 2) #define PCI_D3hot ((pci_power_t __force) 3) #define PCI_D3cold ((pci_power_t __force) 4) #define PCI_POWER_ERROR ((pci_power_t __force) -1) /* * The pci_dev structure is used to describe PCI devices. */ struct pci_dev { struct list_head global_list; /* node in list of all PCI devices */ struct list_head bus_list; /* node in per-bus list */ struct pci_bus *bus; /* bus this device is on */ struct pci_bus *subordinate; /* bus this device bridges to */ void *sysdata; /* hook for sys-specific extension */ struct proc_dir_entry *procent; /* device entry in /proc/bus/pci */ unsigned int devfn; /* encoded device & function index */ unsigned short vendor; unsigned short device; unsigned short subsystem_vendor; unsigned short subsystem_device; unsigned int class; /* 3 bytes: (base,sub,prog-if) */ u8 hdr_type; /* PCI header type (`multi' flag masked out) */ u8 rom_base_reg; /* which config register controls the ROM */ struct pci_driver *driver; /* which driver has allocated this device */ u64 dma_mask; /* Mask of the bits of bus address this device implements. Normally this is 0xffffffff. You only need to change this if your device has broken DMA or supports 64-bit transfers. */ pci_power_t current_state; /* Current operating state. In ACPI-speak, this is D0-D3, D0 being fully functional, and D3 being off. */ struct device dev; /* Generic device interface */ /* device is compatible with these IDs */ unsigned short vendor_compatible[DEVICE_COUNT_COMPATIBLE]; unsigned short device_compatible[DEVICE_COUNT_COMPATIBLE]; int cfg_size; /* Size of configuration space */ /* * Instead of touching interrupt line and base address registers * directly, use the values stored here. They might be different! */ unsigned int irq; struct resource resource[DEVICE_COUNT_RESOURCE]; /* I/O and memory regions + expansion ROMs */ /* These fields are used by common fixups */ unsigned int transparent:1; /* Transparent PCI bridge */ unsigned int multifunction:1;/* Part of multi-function device */ /* keep track of device state */ unsigned int is_enabled:1; /* pci_enable_device has been called */ unsigned int is_busmaster:1; /* device is busmaster */ u32 saved_config_space[16]; /* config space saved at suspend time */ struct bin_attribute *rom_attr; /* attribute descriptor for sysfs ROM entry */ int rom_attr_enabled; /* has display of the rom attribute been enabled? */ struct bin_attribute *res_attr[DEVICE_COUNT_RESOURCE]; /* sysfs file for resources */ #ifdef CONFIG_PCI_NAMES #define PCI_NAME_SIZE 255 #define PCI_NAME_HALF __stringify(43) /* less than half to handle slop */ char pretty_name[PCI_NAME_SIZE]; /* pretty name for users to see */ #endif }; #define pci_dev_g(n) list_entry(n, struct pci_dev, global_list) #define pci_dev_b(n) list_entry(n, struct pci_dev, bus_list) #define to_pci_dev(n) container_of(n, struct pci_dev, dev) #define for_each_pci_dev(d) while ((d = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, d)) != NULL) /* * For PCI devices, the region numbers are assigned this way: * * 0-5 standard PCI regions * 6 expansion ROM * 7-10 bridges: address space assigned to buses behind the bridge */ #define PCI_ROM_RESOURCE 6 #define PCI_BRIDGE_RESOURCES 7 #define PCI_NUM_RESOURCES 11 #ifndef PCI_BUS_NUM_RESOURCES #define PCI_BUS_NUM_RESOURCES 8 #endif #define PCI_REGION_FLAG_MASK 0x0fU /* These bits of resource flags tell us the PCI region flags */ struct pci_bus { struct list_head node; /* node in list of buses */ struct pci_bus *parent; /* parent bus this bridge is on */ struct list_head children; /* list of child buses */ struct list_head devices; /* list of devices on this bus */ struct pci_dev *self; /* bridge device as seen by parent */ struct resource *resource[PCI_BUS_NUM_RESOURCES]; /* address space routed to this bus */ struct pci_ops *ops; /* configuration access functions */ void *sysdata; /* hook for sys-specific extension */ struct proc_dir_entry *procdir; /* directory entry in /proc/bus/pci */ unsigned char number; /* bus number */ unsigned char primary; /* number of primary bridge */ unsigned char secondary; /* number of secondary bridge */ unsigned char subordinate; /* max number of subordinate buses */ char name[48]; unsigned short bridge_ctl; /* manage NO_ISA/FBB/et al behaviors */ unsigned short pad2; struct device *bridge; struct class_device class_dev; struct bin_attribute *legacy_io; /* legacy I/O for this bus */ struct bin_attribute *legacy_mem; /* legacy mem */ }; #define pci_bus_b(n) list_entry(n, struct pci_bus, node) #define to_pci_bus(n) container_of(n, struct pci_bus, class_dev) /* * Error values that may be returned by PCI functions. */ #define PCIBIOS_SUCCESSFUL 0x00 #define PCIBIOS_FUNC_NOT_SUPPORTED 0x81 #define PCIBIOS_BAD_VENDOR_ID 0x83 #define PCIBIOS_DEVICE_NOT_FOUND 0x86 #define PCIBIOS_BAD_REGISTER_NUMBER 0x87 #define PCIBIOS_SET_FAILED 0x88 #define PCIBIOS_BUFFER_TOO_SMALL 0x89 /* Low-level architecture-dependent routines */ struct pci_ops { int (*read)(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *val); int (*write)(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 val); }; struct pci_raw_ops { int (*read)(unsigned int domain, unsigned int bus, unsigned int devfn, int reg, int len, u32 *val); int (*write)(unsigned int domain, unsigned int bus, unsigned int devfn, int reg, int len, u32 val); }; extern struct pci_raw_ops *raw_pci_ops; struct pci_bus_region { unsigned long start; unsigned long end; }; struct pci_dynids { spinlock_t lock; /* protects list, index */ struct list_head list; /* for IDs added at runtime */ unsigned int use_driver_data:1; /* pci_driver->driver_data is used */ }; struct module; struct pci_driver { struct list_head node; char *name; struct module *owner; const struct pci_device_id *id_table; /* must be non-NULL for probe to be called */ int (*probe) (struct pci_dev *dev, const struct pci_device_id *id); /* New device inserted */ void (*remove) (struct pci_dev *dev); /* Device removed (NULL if not a hot-plug capable driver) */ int (*suspend) (struct pci_dev *dev, pm_message_t state); /* Device suspended */ int (*resume) (struct pci_dev *dev); /* Device woken up */ int (*enable_wake) (struct pci_dev *dev, pci_power_t state, int enable); /* Enable wake event */ void (*shutdown) (struct pci_dev *dev); struct device_driver driver; struct pci_dynids dynids; }; #define to_pci_driver(drv) container_of(drv,struct pci_driver, driver) /** * PCI_DEVICE - macro used to describe a specific pci device * @vend: the 16 bit PCI Vendor ID * @dev: the 16 bit PCI Device ID * * This macro is used to create a struct pci_device_id that matches a * specific device. The subvendor and subdevice fields will be set to * PCI_ANY_ID. */ #define PCI_DEVICE(vend,dev) \ .vendor = (vend), .device = (dev), \ .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID /** * PCI_DEVICE_CLASS - macro used to describe a specific pci device class * @dev_class: the class, subclass, prog-if triple for this device * @dev_class_mask: the class mask for this device * * This macro is used to create a struct pci_device_id that matches a * specific PCI class. The vendor, device, subvendor, and subdevice * fields will be set to PCI_ANY_ID. */ #define PCI_DEVICE_CLASS(dev_class,dev_class_mask) \ .class = (dev_class), .class_mask = (dev_class_mask), \ .vendor = PCI_ANY_ID, .device = PCI_ANY_ID, \ .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID /* * pci_module_init is obsolete, this stays here till we fix up all usages of it * in the tree. */ #define pci_module_init pci_register_driver /* these external functions are only available when PCI support is enabled */ #ifdef CONFIG_PCI extern struct bus_type pci_bus_type; /* Do NOT directly access these two variables, unless you are arch specific pci * code, or pci core code. */ extern struct list_head pci_root_buses; /* list of all known PCI buses */ extern struct list_head pci_devices; /* list of all devices */ void pcibios_fixup_bus(struct pci_bus *); int pcibios_enable_device(struct pci_dev *, int mask); char *pcibios_setup (char *str); /* Used only when drivers/pci/setup.c is used */ void pcibios_align_resource(void *, struct resource *, unsigned long, unsigned long); void pcibios_update_irq(struct pci_dev *, int irq); /* Generic PCI functions used internally */ extern struct pci_bus *pci_find_bus(int domain, int busnr); void pci_bus_add_devices(struct pci_bus *bus); struct pci_bus *pci_scan_bus_parented(struct device *parent, int bus, struct pci_ops *ops, void *sysdata); static inline struct pci_bus *pci_scan_bus(int bus, struct pci_ops *ops, void *sysdata) { struct pci_bus *root_bus; root_bus = pci_scan_bus_parented(NULL, bus, ops, sysdata); if (root_bus) pci_bus_add_devices(root_bus); return root_bus; } int pci_scan_slot(struct pci_bus *bus, int devfn); struct pci_dev * pci_scan_single_device(struct pci_bus *bus, int devfn); unsigned int pci_scan_child_bus(struct pci_bus *bus); void pci_bus_add_device(struct pci_dev *dev); void pci_name_device(struct pci_dev *dev); char *pci_class_name(u32 class); void pci_read_bridge_bases(struct pci_bus *child); struct resource *pci_find_parent_resource(const struct pci_dev *dev, struct resource *res); int pci_get_interrupt_pin(struct pci_dev *dev, struct pci_dev **bridge); extern struct pci_dev *pci_dev_get(struct pci_dev *dev); extern void pci_dev_put(struct pci_dev *dev); extern void pci_remove_bus(struct pci_bus *b); extern void pci_remove_bus_device(struct pci_dev *dev); /* Generic PCI functions exported to card drivers */ struct pci_dev *pci_find_device (unsigned int vendor, unsigned int device, const struct pci_dev *from); struct pci_dev *pci_find_device_reverse (unsigned int vendor, unsigned int device, const struct pci_dev *from); struct pci_dev *pci_find_slot (unsigned int bus, unsigned int devfn); int pci_find_capability (struct pci_dev *dev, int cap); int pci_find_ext_capability (struct pci_dev *dev, int cap); struct pci_bus * pci_find_next_bus(const struct pci_bus *from); struct pci_dev *pci_get_device (unsigned int vendor, unsigned int device, struct pci_dev *from); struct pci_dev *pci_get_subsys (unsigned int vendor, unsigned int device, unsigned int ss_vendor, unsigned int ss_device, struct pci_dev *from); struct pci_dev *pci_get_slot (struct pci_bus *bus, unsigned int devfn); struct pci_dev *pci_get_class (unsigned int class, struct pci_dev *from); int pci_dev_present(const struct pci_device_id *ids); int pci_bus_read_config_byte (struct pci_bus *bus, unsigned int devfn, int where, u8 *val); int pci_bus_read_config_word (struct pci_bus *bus, unsigned int devfn, int where, u16 *val); int pci_bus_read_config_dword (struct pci_bus *bus, unsigned int devfn, int where, u32 *val); int pci_bus_write_config_byte (struct pci_bus *bus, unsigned int devfn, int where, u8 val); int pci_bus_write_config_word (struct pci_bus *bus, unsigned int devfn, int where, u16 val); int pci_bus_write_config_dword (struct pci_bus *bus, unsigned int devfn, int where, u32 val); static inline int pci_read_config_byte(struct pci_dev *dev, int where, u8 *val) { return pci_bus_read_config_byte (dev->bus, dev->devfn, where, val); } static inline int pci_read_config_word(struct pci_dev *dev, int where, u16 *val) { return pci_bus_read_config_word (dev->bus, dev->devfn, where, val); } static inline int pci_read_config_dword(struct pci_dev *dev, int where, u32 *val) { return pci_bus_read_config_dword (dev->bus, dev->devfn, where, val); } static inline int pci_write_config_byte(struct pci_dev *dev, int where, u8 val) { return pci_bus_write_config_byte (dev->bus, dev->devfn, where, val); } static inline int pci_write_config_word(struct pci_dev *dev, int where, u16 val) { return pci_bus_write_config_word (dev->bus, dev->devfn, where, val); } static inline int pci_write_config_dword(struct pci_dev *dev, int where, u32 val) { return pci_bus_write_config_dword (dev->bus, dev->devfn, where, val); } int pci_enable_device(struct pci_dev *dev); int pci_enable_device_bars(struct pci_dev *dev, int mask); void pci_disable_device(struct pci_dev *dev); void pci_set_master(struct pci_dev *dev); #define HAVE_PCI_SET_MWI int pci_set_mwi(struct pci_dev *dev); void pci_clear_mwi(struct pci_dev *dev); int pci_set_dma_mask(struct pci_dev *dev, u64 mask); int pci_set_consistent_dma_mask(struct pci_dev *dev, u64 mask); int pci_assign_resource(struct pci_dev *dev, int i); /* ROM control related routines */ void __iomem *pci_map_rom(struct pci_dev *pdev, size_t *size); void __iomem *pci_map_rom_copy(struct pci_dev *pdev, size_t *size); void pci_unmap_rom(struct pci_dev *pdev, void __iomem *rom); void pci_remove_rom(struct pci_dev *pdev); /* Power management related routines */ int pci_save_state(struct pci_dev *dev); int pci_restore_state(struct pci_dev *dev); int pci_set_power_state(struct pci_dev *dev, pci_power_t state); pci_power_t pci_choose_state(struct pci_dev *dev, pm_message_t state); int pci_enable_wake(struct pci_dev *dev, pci_power_t state, int enable); /* Helper functions for low-level code (drivers/pci/setup-[bus,res].c) */ void pci_bus_assign_resources(struct pci_bus *bus); void pci_bus_size_bridges(struct pci_bus *bus); int pci_claim_resource(struct pci_dev *, int); void pci_assign_unassigned_resources(void); void pdev_enable_device(struct pci_dev *); void pdev_sort_resources(struct pci_dev *, struct resource_list *); void pci_fixup_irqs(u8 (*)(struct pci_dev *, u8 *), int (*)(struct pci_dev *, u8, u8)); #define HAVE_PCI_REQ_REGIONS 2 int pci_request_regions(struct pci_dev *, char *); void pci_release_regions(struct pci_dev *); int pci_request_region(struct pci_dev *, int, char *); void pci_release_region(struct pci_dev *, int); /* drivers/pci/bus.c */ int pci_bus_alloc_resource(struct pci_bus *bus, struct resource *res, unsigned long size, unsigned long align, unsigned long min, unsigned int type_mask, void (*alignf)(void *, struct resource *, unsigned long, unsigned long), void *alignf_data); void pci_enable_bridges(struct pci_bus *bus); /* New-style probing supporting hot-pluggable devices */ int pci_register_driver(struct pci_driver *); void pci_unregister_driver(struct pci_driver *); void pci_remove_behind_bridge(struct pci_dev *); struct pci_driver *pci_dev_driver(const struct pci_dev *); const struct pci_device_id *pci_match_device(struct pci_driver *drv, struct pci_dev *dev); const struct pci_device_id *pci_match_id(const struct pci_device_id *ids, struct pci_dev *dev); int pci_scan_bridge(struct pci_bus *bus, struct pci_dev * dev, int max, int pass); /* kmem_cache style wrapper around pci_alloc_consistent() */ #include #define pci_pool dma_pool #define pci_pool_create(name, pdev, size, align, allocation) \ dma_pool_create(name, &pdev->dev, size, align, allocation) #define pci_pool_destroy(pool) dma_pool_destroy(pool) #define pci_pool_alloc(pool, flags, handle) dma_pool_alloc(pool, flags, handle) #define pci_pool_free(pool, vaddr, addr) dma_pool_free(pool, vaddr, addr) enum pci_dma_burst_strategy { PCI_DMA_BURST_INFINITY, /* make bursts as large as possible, strategy_parameter is N/A */ PCI_DMA_BURST_BOUNDARY, /* disconnect at every strategy_parameter byte boundaries */ PCI_DMA_BURST_MULTIPLE, /* disconnect at some multiple of strategy_parameter byte boundaries */ }; #if defined(CONFIG_ISA) || defined(CONFIG_EISA) extern struct pci_dev *isa_bridge; #endif struct msix_entry { u16 vector; /* kernel uses to write allocated vector */ u16 entry; /* driver uses to specify entry, OS writes */ }; #ifndef CONFIG_PCI_MSI static inline void pci_scan_msi_device(struct pci_dev *dev) {} static inline int pci_enable_msi(struct pci_dev *dev) {return -1;} static inline void pci_disable_msi(struct pci_dev *dev) {} static inline int pci_enable_msix(struct pci_dev* dev, struct msix_entry *entries, int nvec) {return -1;} static inline void pci_disable_msix(struct pci_dev *dev) {} static inline void msi_remove_pci_irq_vectors(struct pci_dev *dev) {} #else extern void pci_scan_msi_device(struct pci_dev *dev); extern int pci_enable_msi(struct pci_dev *dev); extern void pci_disable_msi(struct pci_dev *dev); extern int pci_enable_msix(struct pci_dev* dev, struct msix_entry *entries, int nvec); extern void pci_disable_msix(struct pci_dev *dev); extern void msi_remove_pci_irq_vectors(struct pci_dev *dev); #endif #endif /* CONFIG_PCI */ /* Include architecture-dependent settings and functions */ #include /* * If the system does not have PCI, clearly these return errors. Define * these as simple inline functions to avoid hair in drivers. */ #ifndef CONFIG_PCI #define _PCI_NOP(o,s,t) \ static inline int pci_##o##_config_##s (struct pci_dev *dev, int where, t val) \ { return PCIBIOS_FUNC_NOT_SUPPORTED; } #define _PCI_NOP_ALL(o,x) _PCI_NOP(o,byte,u8 x) \ _PCI_NOP(o,word,u16 x) \ _PCI_NOP(o,dword,u32 x) _PCI_NOP_ALL(read, *) _PCI_NOP_ALL(write,) static inline struct pci_dev *pci_find_device(unsigned int vendor, unsigned int device, const struct pci_dev *from) { return NULL; } static inline struct pci_dev *pci_find_slot(unsigned int bus, unsigned int devfn) { return NULL; } static inline struct pci_dev *pci_get_device (unsigned int vendor, unsigned int device, struct pci_dev *from) { return NULL; } static inline struct pci_dev *pci_get_subsys (unsigned int vendor, unsigned int device, unsigned int ss_vendor, unsigned int ss_device, struct pci_dev *from) { return NULL; } static inline struct pci_dev *pci_get_class(unsigned int class, struct pci_dev *from) { return NULL; } #define pci_dev_present(ids) (0) #define pci_dev_put(dev) do { } while (0) static inline void pci_set_master(struct pci_dev *dev) { } static inline int pci_enable_device(struct pci_dev *dev) { return -EIO; } static inline void pci_disable_device(struct pci_dev *dev) { } static inline int pci_set_dma_mask(struct pci_dev *dev, u64 mask) { return -EIO; } static inline int pci_assign_resource(struct pci_dev *dev, int i) { return -EBUSY;} static inline int pci_register_driver(struct pci_driver *drv) { return 0;} static inline void pci_unregister_driver(struct pci_driver *drv) { } static inline int pci_find_capability (struct pci_dev *dev, int cap) {return 0; } static inline int pci_find_ext_capability (struct pci_dev *dev, int cap) {return 0; } static inline const struct pci_device_id *pci_match_device(const struct pci_device_id *ids, const struct pci_dev *dev) { return NULL; } /* Power management related routines */ static inline int pci_save_state(struct pci_dev *dev) { return 0; } static inline int pci_restore_state(struct pci_dev *dev) { return 0; } static inline int pci_set_power_state(struct pci_dev *dev, pci_power_t state) { return 0; } static inline pci_power_t pci_choose_state(struct pci_dev *dev, pm_message_t state) { return PCI_D0; } static inline int pci_enable_wake(struct pci_dev *dev, pci_power_t state, int enable) { return 0; } #define isa_bridge ((struct pci_dev *)NULL) #else /* * PCI domain support. Sometimes called PCI segment (eg by ACPI), * a PCI domain is defined to be a set of PCI busses which share * configuration space. */ #ifndef CONFIG_PCI_DOMAINS static inline int pci_domain_nr(struct pci_bus *bus) { return 0; } static inline int pci_proc_domain(struct pci_bus *bus) { return 0; } #endif #define pci_dma_burst_advice(pdev, strat, strategy_parameter) do { } while (0) #endif /* !CONFIG_PCI */ /* these helpers provide future and backwards compatibility * for accessing popular PCI BAR info */ #define pci_resource_start(dev,bar) ((dev)->resource[(bar)].start) #define pci_resource_end(dev,bar) ((dev)->resource[(bar)].end) #define pci_resource_flags(dev,bar) ((dev)->resource[(bar)].flags) #define pci_resource_len(dev,bar) \ ((pci_resource_start((dev),(bar)) == 0 && \ pci_resource_end((dev),(bar)) == \ pci_resource_start((dev),(bar))) ? 0 : \ \ (pci_resource_end((dev),(bar)) - \ pci_resource_start((dev),(bar)) + 1)) /* Similar to the helpers above, these manipulate per-pci_dev * driver-specific data. They are really just a wrapper around * the generic device structure functions of these calls. */ static inline void *pci_get_drvdata (struct pci_dev *pdev) { return dev_get_drvdata(&pdev->dev); } static inline void pci_set_drvdata (struct pci_dev *pdev, void *data) { dev_set_drvdata(&pdev->dev, data); } /* If you want to know what to call your pci_dev, ask this function. * Again, it's a wrapper around the generic device. */ static inline char *pci_name(struct pci_dev *pdev) { return pdev->dev.bus_id; } /* Some archs want to see the pretty pci name, so use this macro */ #ifdef CONFIG_PCI_NAMES #define pci_pretty_name(dev) ((dev)->pretty_name) #else #define pci_pretty_name(dev) "" #endif /* Some archs don't want to expose struct resource to userland as-is * in sysfs and /proc */ #ifndef HAVE_ARCH_PCI_RESOURCE_TO_USER static inline void pci_resource_to_user(const struct pci_dev *dev, int bar, const struct resource *rsrc, u64 *start, u64 *end) { *start = rsrc->start; *end = rsrc->end; } #endif /* HAVE_ARCH_PCI_RESOURCE_TO_USER */ /* * The world is not perfect and supplies us with broken PCI devices. * For at least a part of these bugs we need a work-around, so both * generic (drivers/pci/quirks.c) and per-architecture code can define * fixup hooks to be called for particular buggy devices. */ struct pci_fixup { u16 vendor, device; /* You can use PCI_ANY_ID here of course */ void (*hook)(struct pci_dev *dev); }; enum pci_fixup_pass { pci_fixup_early, /* Before probing BARs */ pci_fixup_header, /* After reading configuration header */ pci_fixup_final, /* Final phase of device fixups */ pci_fixup_enable, /* pci_enable_device() time */ }; /* Anonymous variables would be nice... */ #define DECLARE_PCI_FIXUP_SECTION(section, name, vendor, device, hook) \ static struct pci_fixup __pci_fixup_##name __attribute_used__ \ __attribute__((__section__(#section))) = { vendor, device, hook }; #define DECLARE_PCI_FIXUP_EARLY(vendor, device, hook) \ DECLARE_PCI_FIXUP_SECTION(.pci_fixup_early, \ vendor##device##hook, vendor, device, hook) #define DECLARE_PCI_FIXUP_HEADER(vendor, device, hook) \ DECLARE_PCI_FIXUP_SECTION(.pci_fixup_header, \ vendor##device##hook, vendor, device, hook) #define DECLARE_PCI_FIXUP_FINAL(vendor, device, hook) \ DECLARE_PCI_FIXUP_SECTION(.pci_fixup_final, \ vendor##device##hook, vendor, device, hook) #define DECLARE_PCI_FIXUP_ENABLE(vendor, device, hook) \ DECLARE_PCI_FIXUP_SECTION(.pci_fixup_enable, \ vendor##device##hook, vendor, device, hook) void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev); extern int pci_pci_problems; #define PCIPCI_FAIL 1 #define PCIPCI_TRITON 2 #define PCIPCI_NATOMA 4 #define PCIPCI_VIAETBF 8 #define PCIPCI_VSFX 16 #define PCIPCI_ALIMAGIK 32 #endif /* __KERNEL__ */ #endif /* LINUX_PCI_H */