/* * Definitions for MCT (Magic Control Technology) USB-RS232 Converter Driver * * Copyright (C) 2000 Wolfgang Grandegger (wolfgang@ces.ch) * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This driver is for the device MCT USB-RS232 Converter (25 pin, Model No. * U232-P25) from Magic Control Technology Corp. (there is also a 9 pin * Model No. U232-P9). See http://www.mct.com.tw/products/product_us232.html * for further information. The properties of this device are listed at the end * of this file. This device was used in the Dlink DSB-S25. * * All of the information about the device was acquired by using SniffUSB * on Windows98. The technical details of the reverse engineering are * summarized at the end of this file. */ #ifndef __LINUX_USB_SERIAL_MCT_U232_H #define __LINUX_USB_SERIAL_MCT_U232_H #define MCT_U232_VID 0x0711 /* Vendor Id */ #define MCT_U232_PID 0x0210 /* Original MCT Product Id */ /* U232-P25, Sitecom */ #define MCT_U232_SITECOM_PID 0x0230 /* Sitecom Product Id */ /* DU-H3SP USB BAY hub */ #define MCT_U232_DU_H3SP_PID 0x0200 /* D-Link DU-H3SP USB BAY */ /* Belkin badge the MCT U232-P9 as the F5U109 */ #define MCT_U232_BELKIN_F5U109_VID 0x050d /* Vendor Id */ #define MCT_U232_BELKIN_F5U109_PID 0x0109 /* Product Id */ /* * Vendor Request Interface */ #define MCT_U232_SET_REQUEST_TYPE 0x40 #define MCT_U232_GET_REQUEST_TYPE 0xc0 /* Get Modem Status Register (MSR) */ #define MCT_U232_GET_MODEM_STAT_REQUEST 2 #define MCT_U232_GET_MODEM_STAT_SIZE 1 /* Get Line Control Register (LCR) */ /* ... not used by this driver */ #define MCT_U232_GET_LINE_CTRL_REQUEST 6 #define MCT_U232_GET_LINE_CTRL_SIZE 1 /* Set Baud Rate Divisor */ #define MCT_U232_SET_BAUD_RATE_REQUEST 5 #define MCT_U232_SET_BAUD_RATE_SIZE 4 /* Set Line Control Register (LCR) */ #define MCT_U232_SET_LINE_CTRL_REQUEST 7 #define MCT_U232_SET_LINE_CTRL_SIZE 1 /* Set Modem Control Register (MCR) */ #define MCT_U232_SET_MODEM_CTRL_REQUEST 10 #define MCT_U232_SET_MODEM_CTRL_SIZE 1 /* * This USB device request code is not well understood. It is transmitted by * the MCT-supplied Windows driver whenever the baud rate changes. */ #define MCT_U232_SET_UNKNOWN1_REQUEST 11 /* Unknown functionality */ #define MCT_U232_SET_UNKNOWN1_SIZE 1 /* * This USB device request code appears to control whether CTS is required * during transmission. * * Sending a zero byte allows data transmission to a device which is not * asserting CTS. Sending a '1' byte will cause transmission to be deferred * until the device asserts CTS. */ #define MCT_U232_SET_CTS_REQUEST 12 #define MCT_U232_SET_CTS_SIZE 1 #define MCT_U232_MAX_SIZE 4 /* of MCT_XXX_SIZE */ /* * Baud rate (divisor) * Actually, there are two of them, MCT website calls them "Philips solution" * and "Intel solution". They are the regular MCT and "Sitecom" for us. * This is pointless to document in the header, see the code for the bits. */ static int mct_u232_calculate_baud_rate(struct usb_serial *serial, speed_t value, speed_t *result); /* * Line Control Register (LCR) */ #define MCT_U232_SET_BREAK 0x40 #define MCT_U232_PARITY_SPACE 0x38 #define MCT_U232_PARITY_MARK 0x28 #define MCT_U232_PARITY_EVEN 0x18 #define MCT_U232_PARITY_ODD 0x08 #define MCT_U232_PARITY_NONE 0x00 #define MCT_U232_DATA_BITS_5 0x00 #define MCT_U232_DATA_BITS_6 0x01 #define MCT_U232_DATA_BITS_7 0x02 #define MCT_U232_DATA_BITS_8 0x03 #define MCT_U232_STOP_BITS_2 0x04 #define MCT_U232_STOP_BITS_1 0x00 /* * Modem Control Register (MCR) */ #define MCT_U232_MCR_NONE 0x8 /* Deactivate DTR and RTS */ #define MCT_U232_MCR_RTS 0xa /* Activate RTS */ #define MCT_U232_MCR_DTR 0x9 /* Activate DTR */ /* * Modem Status Register (MSR) */ #define MCT_U232_MSR_INDEX 0x0 /* data[index] */ #define MCT_U232_MSR_CD 0x80 /* Current CD */ #define MCT_U232_MSR_RI 0x40 /* Current RI */ #define MCT_U232_MSR_DSR 0x20 /* Current DSR */ #define MCT_U232_MSR_CTS 0x10 /* Current CTS */ #define MCT_U232_MSR_DCD 0x08 /* Delta CD */ #define MCT_U232_MSR_DRI 0x04 /* Delta RI */ #define MCT_U232_MSR_DDSR 0x02 /* Delta DSR */ #define MCT_U232_MSR_DCTS 0x01 /* Delta CTS */ /* * Line Status Register (LSR) */ #define MCT_U232_LSR_INDEX 1 /* data[index] */ #define MCT_U232_LSR_ERR 0x80 /* OE | PE | FE | BI */ #define MCT_U232_LSR_TEMT 0x40 /* transmit register empty */ #define MCT_U232_LSR_THRE 0x20 /* transmit holding register empty */ #define MCT_U232_LSR_BI 0x10 /* break indicator */ #define MCT_U232_LSR_FE 0x08 /* framing error */ #define MCT_U232_LSR_OE 0x02 /* overrun error */ #define MCT_U232_LSR_PE 0x04 /* parity error */ #define MCT_U232_LSR_OE 0x02 /* overrun error */ #define MCT_U232_LSR_DR 0x01 /* receive data ready */ /* ----------------------------------------------------------------------------- * Technical Specification reverse engineered with SniffUSB on Windows98 * ===================================================================== * * The technical details of the device have been acquired be using "SniffUSB" * and the vendor-supplied device driver (version 2.3A) under Windows98. To * identify the USB vendor-specific requests and to assign them to terminal * settings (flow control, baud rate, etc.) the program "SerialSettings" from * William G. Greathouse has been proven to be very useful. I also used the * Win98 "HyperTerminal" and "usb-robot" on Linux for testing. The results and * observations are summarized below: * * The USB requests seem to be directly mapped to the registers of a 8250, * 16450 or 16550 UART. The FreeBSD handbook (appendix F.4 "Input/Output * devices") contains a comprehensive description of UARTs and its registers. * The bit descriptions are actually taken from there. * * * Baud rate (divisor) * ------------------- * * BmRequestType: 0x40 (0100 0000B) * bRequest: 0x05 * wValue: 0x0000 * wIndex: 0x0000 * wLength: 0x0004 * Data: divisor = 115200 / baud_rate * * SniffUSB observations (Nov 2003): Contrary to the 'wLength' value of 4 * shown above, observations with a Belkin F5U109 adapter, using the * MCT-supplied Windows98 driver (U2SPORT.VXD, "File version: 1.21P.0104 for * Win98/Me"), show this request has a length of 1 byte, presumably because * of the fact that the Belkin adapter and the 'Sitecom U232-P25' adapter * use a baud-rate code instead of a conventional RS-232 baud rate divisor. * The current source code for this driver does not reflect this fact, but * the driver works fine with this adapter/driver combination nonetheless. * * * Line Control Register (LCR) * --------------------------- * * BmRequestType: 0x40 (0100 0000B) 0xc0 (1100 0000B) * bRequest: 0x07 0x06 * wValue: 0x0000 * wIndex: 0x0000 * wLength: 0x0001 * Data: LCR (see below) * * Bit 7: Divisor Latch Access Bit (DLAB). When set, access to the data * transmit/receive register (THR/RBR) and the Interrupt Enable Register * (IER) is disabled. Any access to these ports is now redirected to the * Divisor Latch Registers. Setting this bit, loading the Divisor * Registers, and clearing DLAB should be done with interrupts disabled. * Bit 6: Set Break. When set to "1", the transmitter begins to transmit * continuous Spacing until this bit is set to "0". This overrides any * bits of characters that are being transmitted. * Bit 5: Stick Parity. When parity is enabled, setting this bit causes parity * to always be "1" or "0", based on the value of Bit 4. * Bit 4: Even Parity Select (EPS). When parity is enabled and Bit 5 is "0", * setting this bit causes even parity to be transmitted and expected. * Otherwise, odd parity is used. * Bit 3: Parity Enable (PEN). When set to "1", a parity bit is inserted * between the last bit of the data and the Stop Bit. The UART will also * expect parity to be present in the received data. * Bit 2: Number of Stop Bits (STB). If set to "1" and using 5-bit data words, * 1.5 Stop Bits are transmitted and expected in each data word. For * 6, 7 and 8-bit data words, 2 Stop Bits are transmitted and expected. * When this bit is set to "0", one Stop Bit is used on each data word. * Bit 1: Word Length Select Bit #1 (WLSB1) * Bit 0: Word Length Select Bit #0 (WLSB0) * Together these bits specify the number of bits in each data word. * 1 0 Word Length * 0 0 5 Data Bits * 0 1 6 Data Bits * 1 0 7 Data Bits * 1 1 8 Data Bits * * SniffUSB observations: Bit 7 seems not to be used. There seem to be two bugs * in the Win98 driver: the break does not work (bit 6 is not asserted) and the * stick parity bit is not cleared when set once. The LCR can also be read * back with USB request 6 but this has never been observed with SniffUSB. * * * Modem Control Register (MCR) * ---------------------------- * * BmRequestType: 0x40 (0100 0000B) * bRequest: 0x0a * wValue: 0x0000 * wIndex: 0x0000 * wLength: 0x0001 * Data: MCR (Bit 4..7, see below) * * Bit 7: Reserved, always 0. * Bit 6: Reserved, always 0. * Bit 5: Reserved, always 0. * Bit 4: Loop-Back Enable. When set to "1", the UART transmitter and receiver * are internally connected together to allow diagnostic operations. In * addition, the UART modem control outputs are connected to the UART * modem control inputs. CTS is connected to RTS, DTR is connected to * DSR, OUT1 is connected to RI, and OUT 2 is connected to DCD. * Bit 3: OUT 2. An auxiliary output that the host processor may set high or * low. In the IBM PC serial adapter (and most clones), OUT 2 is used * to tri-state (disable) the interrupt signal from the * 8250/16450/16550 UART. * Bit 2: OUT 1. An auxiliary output that the host processor may set high or * low. This output is not used on the IBM PC serial adapter. * Bit 1: Request to Send (RTS). When set to "1", the output of the UART -RTS * line is Low (Active). * Bit 0: Data Terminal Ready (DTR). When set to "1", the output of the UART * -DTR line is Low (Active). * * SniffUSB observations: Bit 2 and 4 seem not to be used but bit 3 has been * seen _always_ set. * * * Modem Status Register (MSR) * --------------------------- * * BmRequestType: 0xc0 (1100 0000B) * bRequest: 0x02 * wValue: 0x0000 * wIndex: 0x0000 * wLength: 0x0001 * Data: MSR (see below) * * Bit 7: Data Carrier Detect (CD). Reflects the state of the DCD line on the * UART. * Bit 6: Ring Indicator (RI). Reflects the state of the RI line on the UART. * Bit 5: Data Set Ready (DSR). Reflects the state of the DSR line on the UART. * Bit 4: Clear To Send (CTS). Reflects the state of the CTS line on the UART. * Bit 3: Delta Data Carrier Detect (DDCD). Set to "1" if the -DCD line has * changed state one more more times since the last time the MSR was * read by the host. * Bit 2: Trailing Edge Ring Indicator (TERI). Set to "1" if the -RI line has * had a low to high transition since the last time the MSR was read by * the host. * Bit 1: Delta Data Set Ready (DDSR). Set to "1" if the -DSR line has changed * state one more more times since the last time the MSR was read by the * host. * Bit 0: Delta Clear To Send (DCTS). Set to "1" if the -CTS line has changed * state one more times since the last time the MSR was read by the * host. * * SniffUSB observations: the MSR is also returned as first byte on the * interrupt-in endpoint 0x83 to signal changes of modem status lines. The USB * request to read MSR cannot be applied during normal device operation. * * * Line Status Register (LSR) * -------------------------- * * Bit 7 Error in Receiver FIFO. On the 8250/16450 UART, this bit is zero. * This bit is set to "1" when any of the bytes in the FIFO have one * or more of the following error conditions: PE, FE, or BI. * Bit 6 Transmitter Empty (TEMT). When set to "1", there are no words * remaining in the transmit FIFO or the transmit shift register. The * transmitter is completely idle. * Bit 5 Transmitter Holding Register Empty (THRE). When set to "1", the * FIFO (or holding register) now has room for at least one additional * word to transmit. The transmitter may still be transmitting when * this bit is set to "1". * Bit 4 Break Interrupt (BI). The receiver has detected a Break signal. * Bit 3 Framing Error (FE). A Start Bit was detected but the Stop Bit did * not appear at the expected time. The received word is probably * garbled. * Bit 2 Parity Error (PE). The parity bit was incorrect for the word * received. * Bit 1 Overrun Error (OE). A new word was received and there was no room * in the receive buffer. The newly-arrived word in the shift register * is discarded. On 8250/16450 UARTs, the word in the holding register * is discarded and the newly- arrived word is put in the holding * register. * Bit 0 Data Ready (DR). One or more words are in the receive FIFO that the * host may read. A word must be completely received and moved from * the shift register into the FIFO (or holding register for * 8250/16450 designs) before this bit is set. * * SniffUSB observations: the LSR is returned as second byte on the * interrupt-in endpoint 0x83 to signal error conditions. Such errors have * been seen with minicom/zmodem transfers (CRC errors). * * * Unknown #1 * ------------------- * * BmRequestType: 0x40 (0100 0000B) * bRequest: 0x0b * wValue: 0x0000 * wIndex: 0x0000 * wLength: 0x0001 * Data: 0x00 * * SniffUSB observations (Nov 2003): With the MCT-supplied Windows98 driver * (U2SPORT.VXD, "File version: 1.21P.0104 for Win98/Me"), this request * occurs immediately after a "Baud rate (divisor)" message. It was not * observed at any other time. It is unclear what purpose this message * serves. * * * Unknown #2 * ------------------- * * BmRequestType: 0x40 (0100 0000B) * bRequest: 0x0c * wValue: 0x0000 * wIndex: 0x0000 * wLength: 0x0001 * Data: 0x00 * * SniffUSB observations (Nov 2003): With the MCT-supplied Windows98 driver * (U2SPORT.VXD, "File version: 1.21P.0104 for Win98/Me"), this request * occurs immediately after the 'Unknown #1' message (see above). It was * not observed at any other time. It is unclear what other purpose (if * any) this message might serve, but without it, the USB/RS-232 adapter * will not write to RS-232 devices which do not assert the 'CTS' signal. * * * Flow control * ------------ * * SniffUSB observations: no flow control specific requests have been realized * apart from DTR/RTS settings. Both signals are dropped for no flow control * but asserted for hardware or software flow control. * * * Endpoint usage * -------------- * * SniffUSB observations: the bulk-out endpoint 0x1 and interrupt-in endpoint * 0x81 is used to transmit and receive characters. The second interrupt-in * endpoint 0x83 signals exceptional conditions like modem line changes and * errors. The first byte returned is the MSR and the second byte the LSR. * * * Other observations * ------------------ * * Queued bulk transfers like used in visor.c did not work. * * * Properties of the USB device used (as found in /var/log/messages) * ----------------------------------------------------------------- * * Manufacturer: MCT Corporation. * Product: USB-232 Interfact Controller * SerialNumber: U2S22050 * * Length = 18 * DescriptorType = 01 * USB version = 1.00 * Vendor:Product = 0711:0210 * MaxPacketSize0 = 8 * NumConfigurations = 1 * Device version = 1.02 * Device Class:SubClass:Protocol = 00:00:00 * Per-interface classes * Configuration: * bLength = 9 * bDescriptorType = 02 * wTotalLength = 0027 * bNumInterfaces = 01 * bConfigurationValue = 01 * iConfiguration = 00 * bmAttributes = c0 * MaxPower = 100mA * * Interface: 0 * Alternate Setting: 0 * bLength = 9 * bDescriptorType = 04 * bInterfaceNumber = 00 * bAlternateSetting = 00 * bNumEndpoints = 03 * bInterface Class:SubClass:Protocol = 00:00:00 * iInterface = 00 * Endpoint: * bLength = 7 * bDescriptorType = 05 * bEndpointAddress = 81 (in) * bmAttributes = 03 (Interrupt) * wMaxPacketSize = 0040 * bInterval = 02 * Endpoint: * bLength = 7 * bDescriptorType = 05 * bEndpointAddress = 01 (out) * bmAttributes = 02 (Bulk) * wMaxPacketSize = 0040 * bInterval = 00 * Endpoint: * bLength = 7 * bDescriptorType = 05 * bEndpointAddress = 83 (in) * bmAttributes = 03 (Interrupt) * wMaxPacketSize = 0002 * bInterval = 02 * * * Hardware details (added by Martin Hamilton, 2001/12/06) * ----------------------------------------------------------------- * * This info was gleaned from opening a Belkin F5U109 DB9 USB serial * adaptor, which turns out to simply be a re-badged U232-P9. We * know this because there is a sticky label on the circuit board * which says "U232-P9" ;-) * * The circuit board inside the adaptor contains a Philips PDIUSBD12 * USB endpoint chip and a Philips P87C52UBAA microcontroller with * embedded UART. Exhaustive documentation for these is available at: * * http://www.semiconductors.philips.com/pip/p87c52ubaa * http://www.nxp.com/acrobat_download/various/PDIUSBD12_PROGRAMMING_GUIDE.pdf * * Thanks to Julian Highfield for the pointer to the Philips database. * */ #endif /* __LINUX_USB_SERIAL_MCT_U232_H */