/************************************************************************ * * USBVEND.H Vendor-specific USB definitions * * NOTE: This must be kept in sync with the Edgeport firmware and * must be kept backward-compatible with older firmware. * ************************************************************************ * * Copyright (C) 1998 Inside Out Networks, Inc. * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * ************************************************************************/ #if !defined(_USBVEND_H) #define _USBVEND_H /************************************************************************ * * D e f i n e s / T y p e d e f s * ************************************************************************/ // // Definitions of USB product IDs // #define USB_VENDOR_ID_ION 0x1608 // Our VID #define USB_VENDOR_ID_TI 0x0451 // TI VID #define USB_VENDOR_ID_AXIOHM 0x05D9 /* Axiohm VID */ // // Definitions of USB product IDs (PID) // We break the USB-defined PID into an OEM Id field (upper 6 bits) // and a Device Id (bottom 10 bits). The Device Id defines what // device this actually is regardless of what the OEM wants to // call it. // // ION-device OEM IDs #define ION_OEM_ID_ION 0 // 00h Inside Out Networks #define ION_OEM_ID_NLYNX 1 // 01h NLynx Systems #define ION_OEM_ID_GENERIC 2 // 02h Generic OEM #define ION_OEM_ID_MAC 3 // 03h Mac Version #define ION_OEM_ID_MEGAWOLF 4 // 04h Lupusb OEM Mac version (MegaWolf) #define ION_OEM_ID_MULTITECH 5 // 05h Multitech Rapidports #define ION_OEM_ID_AGILENT 6 // 06h AGILENT board // ION-device Device IDs // Product IDs - assigned to match middle digit of serial number (No longer true) #define ION_DEVICE_ID_80251_NETCHIP 0x020 // This bit is set in the PID if this edgeport hardware$ // is based on the 80251+Netchip. #define ION_DEVICE_ID_GENERATION_1 0x00 // Value for 930 based edgeports #define ION_DEVICE_ID_GENERATION_2 0x01 // Value for 80251+Netchip. #define ION_DEVICE_ID_GENERATION_3 0x02 // Value for Texas Instruments TUSB5052 chip #define ION_DEVICE_ID_GENERATION_4 0x03 // Watchport Family of products #define ION_GENERATION_MASK 0x03 #define ION_DEVICE_ID_HUB_MASK 0x0080 // This bit in the PID designates a HUB device // for example 8C would be a 421 4 port hub // and 8D would be a 2 port embedded hub #define EDGEPORT_DEVICE_ID_MASK 0x0ff // Not including OEM or GENERATION fields #define ION_DEVICE_ID_UNCONFIGURED_EDGE_DEVICE 0x000 // In manufacturing only #define ION_DEVICE_ID_EDGEPORT_4 0x001 // Edgeport/4 RS232 #define ION_DEVICE_ID_EDGEPORT_8R 0x002 // Edgeport with RJ45 no Ring #define ION_DEVICE_ID_RAPIDPORT_4 0x003 // Rapidport/4 #define ION_DEVICE_ID_EDGEPORT_4T 0x004 // Edgeport/4 RS232 for Telxon (aka "Fleetport") #define ION_DEVICE_ID_EDGEPORT_2 0x005 // Edgeport/2 RS232 #define ION_DEVICE_ID_EDGEPORT_4I 0x006 // Edgeport/4 RS422 #define ION_DEVICE_ID_EDGEPORT_2I 0x007 // Edgeport/2 RS422/RS485 #define ION_DEVICE_ID_EDGEPORT_8RR 0x008 // Edgeport with RJ45 with Data and RTS/CTS only // ION_DEVICE_ID_EDGEPORT_8_HANDBUILT 0x009 // Hand-built Edgeport/8 (Placeholder, used in middle digit of serial number only!) // ION_DEVICE_ID_MULTIMODEM_4X56 0x00A // MultiTech version of RP/4 (Placeholder, used in middle digit of serial number only!) #define ION_DEVICE_ID_EDGEPORT_PARALLEL_PORT 0x00B // Edgeport/(4)21 Parallel port (USS720) #define ION_DEVICE_ID_EDGEPORT_421 0x00C // Edgeport/421 Hub+RS232+Parallel #define ION_DEVICE_ID_EDGEPORT_21 0x00D // Edgeport/21 RS232+Parallel #define ION_DEVICE_ID_EDGEPORT_8_DUAL_CPU 0x00E // Half of an Edgeport/8 (the kind with 2 EP/4s on 1 PCB) #define ION_DEVICE_ID_EDGEPORT_8 0x00F // Edgeport/8 (single-CPU) #define ION_DEVICE_ID_EDGEPORT_2_DIN 0x010 // Edgeport/2 RS232 with Apple DIN connector #define ION_DEVICE_ID_EDGEPORT_4_DIN 0x011 // Edgeport/4 RS232 with Apple DIN connector #define ION_DEVICE_ID_EDGEPORT_16_DUAL_CPU 0x012 // Half of an Edgeport/16 (the kind with 2 EP/8s) #define ION_DEVICE_ID_EDGEPORT_COMPATIBLE 0x013 // Edgeport Compatible, for NCR, Axiohm etc. testing #define ION_DEVICE_ID_EDGEPORT_8I 0x014 // Edgeport/8 RS422 (single-CPU) #define ION_DEVICE_ID_EDGEPORT_1 0x015 // Edgeport/1 RS232 #define ION_DEVICE_ID_EPOS44 0x016 // Half of an EPOS/44 (TIUMP BASED) #define ION_DEVICE_ID_EDGEPORT_42 0x017 // Edgeport/42 #define ION_DEVICE_ID_EDGEPORT_412_8 0x018 // Edgeport/412 8 port part #define ION_DEVICE_ID_EDGEPORT_412_4 0x019 // Edgeport/412 4 port part #define ION_DEVICE_ID_EDGEPORT_22I 0x01A // Edgeport/22I is an Edgeport/4 with ports 1&2 RS422 and ports 3&4 RS232 // Compact Form factor TI based devices 2c, 21c, 22c, 221c #define ION_DEVICE_ID_EDGEPORT_2C 0x01B // Edgeport/2c is a TI based Edgeport/2 - Small I2c #define ION_DEVICE_ID_EDGEPORT_221C 0x01C // Edgeport/221c is a TI based Edgeport/2 with lucent chip and // 2 external hub ports - Large I2C #define ION_DEVICE_ID_EDGEPORT_22C 0x01D // Edgeport/22c is a TI based Edgeport/2 with // 2 external hub ports - Large I2C #define ION_DEVICE_ID_EDGEPORT_21C 0x01E // Edgeport/21c is a TI based Edgeport/2 with lucent chip // Small I2C /* * DANGER DANGER The 0x20 bit was used to indicate a 8251/netchip GEN 2 device. * Since the MAC, Linux, and Optimal drivers still used the old code * I suggest that you skip the 0x20 bit when creating new PIDs */ // Generation 3 devices -- 3410 based edgport/1 (256 byte I2C) #define ION_DEVICE_ID_TI3410_EDGEPORT_1 0x040 // Edgeport/1 RS232 #define ION_DEVICE_ID_TI3410_EDGEPORT_1I 0x041 // Edgeport/1i- RS422 model // Ti based software switchable RS232/RS422/RS485 devices #define ION_DEVICE_ID_EDGEPORT_4S 0x042 // Edgeport/4s - software switchable model #define ION_DEVICE_ID_EDGEPORT_8S 0x043 // Edgeport/8s - software switchable model // Usb to Ethernet dongle #define ION_DEVICE_ID_EDGEPORT_E 0x0E0 // Edgeport/E Usb to Ethernet // Edgeport TI based devices #define ION_DEVICE_ID_TI_EDGEPORT_4 0x0201 // Edgeport/4 RS232 #define ION_DEVICE_ID_TI_EDGEPORT_2 0x0205 // Edgeport/2 RS232 #define ION_DEVICE_ID_TI_EDGEPORT_4I 0x0206 // Edgeport/4i RS422 #define ION_DEVICE_ID_TI_EDGEPORT_2I 0x0207 // Edgeport/2i RS422/RS485 #define ION_DEVICE_ID_TI_EDGEPORT_421 0x020C // Edgeport/421 4 hub 2 RS232 + Parallel (lucent on a different hub port) #define ION_DEVICE_ID_TI_EDGEPORT_21 0x020D // Edgeport/21 2 RS232 + Parallel (lucent on a different hub port) #define ION_DEVICE_ID_TI_EDGEPORT_416 0x0212 // Edgeport/416 #define ION_DEVICE_ID_TI_EDGEPORT_1 0x0215 // Edgeport/1 RS232 #define ION_DEVICE_ID_TI_EDGEPORT_42 0x0217 // Edgeport/42 4 hub 2 RS232 #define ION_DEVICE_ID_TI_EDGEPORT_22I 0x021A // Edgeport/22I is an Edgeport/4 with ports 1&2 RS422 and ports 3&4 RS232 #define ION_DEVICE_ID_TI_EDGEPORT_2C 0x021B // Edgeport/2c RS232 #define ION_DEVICE_ID_TI_EDGEPORT_221C 0x021C // Edgeport/221c is a TI based Edgeport/2 with lucent chip and // 2 external hub ports - Large I2C #define ION_DEVICE_ID_TI_EDGEPORT_22C 0x021D // Edgeport/22c is a TI based Edgeport/2 with // 2 external hub ports - Large I2C #define ION_DEVICE_ID_TI_EDGEPORT_21C 0x021E // Edgeport/21c is a TI based Edgeport/2 with lucent chip // Generation 3 devices -- 3410 based edgport/1 (256 byte I2C) #define ION_DEVICE_ID_TI_TI3410_EDGEPORT_1 0x0240 // Edgeport/1 RS232 #define ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I 0x0241 // Edgeport/1i- RS422 model // Ti based software switchable RS232/RS422/RS485 devices #define ION_DEVICE_ID_TI_EDGEPORT_4S 0x0242 // Edgeport/4s - software switchable model #define ION_DEVICE_ID_TI_EDGEPORT_8S 0x0243 // Edgeport/8s - software switchable model #define ION_DEVICE_ID_TI_EDGEPORT_8 0x0244 // Edgeport/8 (single-CPU) #define ION_DEVICE_ID_TI_EDGEPORT_416B 0x0247 // Edgeport/416 /************************************************************************ * * Generation 4 devices * ************************************************************************/ // Watchport based on 3410 both 1-wire and binary products (16K I2C) #define ION_DEVICE_ID_WP_UNSERIALIZED 0x300 // Watchport based on 3410 both 1-wire and binary products #define ION_DEVICE_ID_WP_PROXIMITY 0x301 // Watchport/P Discontinued #define ION_DEVICE_ID_WP_MOTION 0x302 // Watchport/M #define ION_DEVICE_ID_WP_MOISTURE 0x303 // Watchport/W #define ION_DEVICE_ID_WP_TEMPERATURE 0x304 // Watchport/T #define ION_DEVICE_ID_WP_HUMIDITY 0x305 // Watchport/H #define ION_DEVICE_ID_WP_POWER 0x306 // Watchport #define ION_DEVICE_ID_WP_LIGHT 0x307 // Watchport #define ION_DEVICE_ID_WP_RADIATION 0x308 // Watchport #define ION_DEVICE_ID_WP_ACCELERATION 0x309 // Watchport/A #define ION_DEVICE_ID_WP_DISTANCE 0x30A // Watchport/D Discontinued #define ION_DEVICE_ID_WP_PROX_DIST 0x30B // Watchport/D uses distance sensor // Default to /P function #define ION_DEVICE_ID_PLUS_PWR_HP4CD 0x30C // 5052 Plus Power HubPort/4CD+ (for Dell) #define ION_DEVICE_ID_PLUS_PWR_HP4C 0x30D // 5052 Plus Power HubPort/4C+ #define ION_DEVICE_ID_PLUS_PWR_PCI 0x30E // 3410 Plus Power PCI Host Controller 4 port // // Definitions for AXIOHM USB product IDs // #define USB_VENDOR_ID_AXIOHM 0x05D9 // Axiohm VID #define AXIOHM_DEVICE_ID_MASK 0xffff #define AXIOHM_DEVICE_ID_EPIC_A758 0xA758 #define AXIOHM_DEVICE_ID_EPIC_A794 0xA794 #define AXIOHM_DEVICE_ID_EPIC_A225 0xA225 // // Definitions for NCR USB product IDs // #define USB_VENDOR_ID_NCR 0x0404 // NCR VID #define NCR_DEVICE_ID_MASK 0xffff #define NCR_DEVICE_ID_EPIC_0202 0x0202 #define NCR_DEVICE_ID_EPIC_0203 0x0203 #define NCR_DEVICE_ID_EPIC_0310 0x0310 #define NCR_DEVICE_ID_EPIC_0311 0x0311 #define NCR_DEVICE_ID_EPIC_0312 0x0312 // // Definitions for SYMBOL USB product IDs // #define USB_VENDOR_ID_SYMBOL 0x05E0 // Symbol VID #define SYMBOL_DEVICE_ID_MASK 0xffff #define SYMBOL_DEVICE_ID_KEYFOB 0x0700 // // Definitions for other product IDs #define ION_DEVICE_ID_MT4X56USB 0x1403 // OEM device #define GENERATION_ID_FROM_USB_PRODUCT_ID(ProductId) \ ((__u16) ((ProductId >> 8) & (ION_GENERATION_MASK))) #define MAKE_USB_PRODUCT_ID(OemId, DeviceId) \ ((__u16) (((OemId) << 10) || (DeviceId))) #define DEVICE_ID_FROM_USB_PRODUCT_ID(ProductId) \ ((__u16) ((ProductId) & (EDGEPORT_DEVICE_ID_MASK))) #define OEM_ID_FROM_USB_PRODUCT_ID(ProductId) \ ((__u16) (((ProductId) >> 10) & 0x3F)) // // Definitions of parameters for download code. Note that these are // specific to a given version of download code and must change if the // corresponding download code changes. // // TxCredits value below which driver won't bother sending (to prevent too many small writes). // Send only if above 25% #define EDGE_FW_GET_TX_CREDITS_SEND_THRESHOLD(InitialCredit, MaxPacketSize) (max(((InitialCredit) / 4), (MaxPacketSize))) #define EDGE_FW_BULK_MAX_PACKET_SIZE 64 // Max Packet Size for Bulk In Endpoint (EP1) #define EDGE_FW_BULK_READ_BUFFER_SIZE 1024 // Size to use for Bulk reads #define EDGE_FW_INT_MAX_PACKET_SIZE 32 // Max Packet Size for Interrupt In Endpoint // Note that many units were shipped with MPS=16, we // force an upgrade to this value). #define EDGE_FW_INT_INTERVAL 2 // 2ms polling on IntPipe // // Definitions of I/O Networks vendor-specific requests // for default endpoint // // bmRequestType = 01000000 Set vendor-specific, to device // bmRequestType = 11000000 Get vendor-specific, to device // // These are the definitions for the bRequest field for the // above bmRequestTypes. // // For the read/write Edgeport memory commands, the parameters // are as follows: // wValue = 16-bit address // wIndex = unused (though we could put segment 00: or FF: here) // wLength = # bytes to read/write (max 64) // #define USB_REQUEST_ION_RESET_DEVICE 0 // Warm reboot Edgeport, retaining USB address #define USB_REQUEST_ION_GET_EPIC_DESC 1 // Get Edgeport Compatibility Descriptor // unused 2 // Unused, available #define USB_REQUEST_ION_READ_RAM 3 // Read EdgePort RAM at specified addr #define USB_REQUEST_ION_WRITE_RAM 4 // Write EdgePort RAM at specified addr #define USB_REQUEST_ION_READ_ROM 5 // Read EdgePort ROM at specified addr #define USB_REQUEST_ION_WRITE_ROM 6 // Write EdgePort ROM at specified addr #define USB_REQUEST_ION_EXEC_DL_CODE 7 // Begin execution of RAM-based download // code by jumping to address in wIndex:wValue // 8 // Unused, available #define USB_REQUEST_ION_ENABLE_SUSPEND 9 // Enable/Disable suspend feature // (wValue != 0: Enable; wValue = 0: Disable) #define USB_REQUEST_ION_SEND_IOSP 10 // Send an IOSP command to the edgeport over the control pipe #define USB_REQUEST_ION_RECV_IOSP 11 // Receive an IOSP command from the edgeport over the control pipe #define USB_REQUEST_ION_DIS_INT_TIMER 0x80 // Sent to Axiohm to enable/ disable // interrupt token timer // wValue = 1, enable (default) // wValue = 0, disable // // Define parameter values for our vendor-specific commands // // // Edgeport Compatibility Descriptor // // This descriptor is only returned by Edgeport-compatible devices // supporting the EPiC spec. True ION devices do not return this // descriptor, but instead return STALL on receipt of the // GET_EPIC_DESC command. The driver interprets a STALL to mean that // this is a "real" Edgeport. // struct edge_compatibility_bits { // This __u32 defines which Vendor-specific commands/functionality // the device supports on the default EP0 pipe. __u32 VendEnableSuspend : 1; // 0001 Set if device supports ION_ENABLE_SUSPEND __u32 VendUnused : 31; // Available for future expansion, must be 0 // This __u32 defines which IOSP commands are supported over the // bulk pipe EP1. // xxxx Set if device supports: __u32 IOSPOpen : 1; // 0001 OPEN / OPEN_RSP (Currently must be 1) __u32 IOSPClose : 1; // 0002 CLOSE __u32 IOSPChase : 1; // 0004 CHASE / CHASE_RSP __u32 IOSPSetRxFlow : 1; // 0008 SET_RX_FLOW __u32 IOSPSetTxFlow : 1; // 0010 SET_TX_FLOW __u32 IOSPSetXChar : 1; // 0020 SET_XON_CHAR/SET_XOFF_CHAR __u32 IOSPRxCheck : 1; // 0040 RX_CHECK_REQ/RX_CHECK_RSP __u32 IOSPSetClrBreak : 1; // 0080 SET_BREAK/CLEAR_BREAK __u32 IOSPWriteMCR : 1; // 0100 MCR register writes (set/clr DTR/RTS) __u32 IOSPWriteLCR : 1; // 0200 LCR register writes (wordlen/stop/parity) __u32 IOSPSetBaudRate : 1; // 0400 setting Baud rate (writes to LCR.80h and DLL/DLM register) __u32 IOSPDisableIntPipe : 1; // 0800 Do not use the interrupt pipe for TxCredits or RxButesAvailable __u32 IOSPRxDataAvail : 1; // 1000 Return status of RX Fifo (Data available in Fifo) __u32 IOSPTxPurge : 1; // 2000 Purge TXBuffer and/or Fifo in Edgeport hardware __u32 IOSPUnused : 18; // Available for future expansion, must be 0 // This __u32 defines which 'general' features are supported __u32 TrueEdgeport : 1; // 0001 Set if device is a 'real' Edgeport // (Used only by driver, NEVER set by an EPiC device) __u32 GenUnused : 31; // Available for future expansion, must be 0 }; #define EDGE_COMPATIBILITY_MASK0 0x0001 #define EDGE_COMPATIBILITY_MASK1 0x3FFF #define EDGE_COMPATIBILITY_MASK2 0x0001 struct edge_compatibility_descriptor { __u8 Length; // Descriptor Length (per USB spec) __u8 DescType; // Descriptor Type (per USB spec, =DEVICE type) __u8 EpicVer; // Version of EPiC spec supported // (Currently must be 1) __u8 NumPorts; // Number of serial ports supported __u8 iDownloadFile; // Index of string containing download code filename // 0=no download, FF=download compiled into driver. __u8 Unused[3]; // Available for future expansion, must be 0 // (Currently must be 0). __u8 MajorVersion; // Firmware version: xx. __u8 MinorVersion; // yy. __le16 BuildNumber; // zzzz (LE format) // The following structure contains __u32s, with each bit // specifying whether the EPiC device supports the given // command or functionality. struct edge_compatibility_bits Supports; }; // Values for iDownloadFile #define EDGE_DOWNLOAD_FILE_NONE 0 // No download requested #define EDGE_DOWNLOAD_FILE_INTERNAL 0xFF // Download the file compiled into driver (930 version) #define EDGE_DOWNLOAD_FILE_I930 0xFF // Download the file compiled into driver (930 version) #define EDGE_DOWNLOAD_FILE_80251 0xFE // Download the file compiled into driver (80251 version) /* * Special addresses for READ/WRITE_RAM/ROM */ // Version 1 (original) format of DeviceParams #define EDGE_MANUF_DESC_ADDR_V1 0x00FF7F00 #define EDGE_MANUF_DESC_LEN_V1 sizeof(EDGE_MANUF_DESCRIPTOR_V1) // Version 2 format of DeviceParams. This format is longer (3C0h) // and starts lower in memory, at the uppermost 1K in ROM. #define EDGE_MANUF_DESC_ADDR 0x00FF7C00 #define EDGE_MANUF_DESC_LEN sizeof(struct edge_manuf_descriptor) // Boot params descriptor #define EDGE_BOOT_DESC_ADDR 0x00FF7FC0 #define EDGE_BOOT_DESC_LEN sizeof(struct edge_boot_descriptor) // Define the max block size that may be read or written // in a read/write RAM/ROM command. #define MAX_SIZE_REQ_ION_READ_MEM ((__u16)64) #define MAX_SIZE_REQ_ION_WRITE_MEM ((__u16)64) // // Notes for the following two ION vendor-specific param descriptors: // // 1. These have a standard USB descriptor header so they look like a // normal descriptor. // 2. Any strings in the structures are in USB-defined string // descriptor format, so that they may be separately retrieved, // if necessary, with a minimum of work on the 930. This also // requires them to be in UNICODE format, which, for English at // least, simply means extending each __u8 into a __u16. // 3. For all fields, 00 means 'uninitialized'. // 4. All unused areas should be set to 00 for future expansion. // // This structure is ver 2 format. It contains ALL USB descriptors as // well as the configuration parameters that were in the original V1 // structure. It is NOT modified when new boot code is downloaded; rather, // these values are set or modified by manufacturing. It is located at // xC00-xFBF (length 3C0h) in the ROM. // This structure is a superset of the v1 structure and is arranged so // that all of the v1 fields remain at the same address. We are just // adding more room to the front of the structure to hold the descriptors. // // The actual contents of this structure are defined in a 930 assembly // file, converted to a binary image, and then written by the serialization // program. The C definition of this structure just defines a dummy // area for general USB descriptors and the descriptor tables (the root // descriptor starts at xC00). At the bottom of the structure are the // fields inherited from the v1 structure. #define MAX_SERIALNUMBER_LEN 12 #define MAX_ASSEMBLYNUMBER_LEN 14 struct edge_manuf_descriptor { __u16 RootDescTable[0x10]; // C00 Root of descriptor tables (just a placeholder) __u8 DescriptorArea[0x2E0]; // C20 Descriptors go here, up to 2E0h (just a placeholder) // Start of v1-compatible section __u8 Length; // F00 Desc length for what follows, per USB (= C0h ) __u8 DescType; // F01 Desc type, per USB (=DEVICE type) __u8 DescVer; // F02 Desc version/format (currently 2) __u8 NumRootDescEntries; // F03 # entries in RootDescTable __u8 RomSize; // F04 Size of ROM/E2PROM in K __u8 RamSize; // F05 Size of external RAM in K __u8 CpuRev; // F06 CPU revision level (chg only if s/w visible) __u8 BoardRev; // F07 PCB revision level (chg only if s/w visible) __u8 NumPorts; // F08 Number of ports __u8 DescDate[3]; // F09 MM/DD/YY when descriptor template was compiler, // so host can track changes to USB-only descriptors. __u8 SerNumLength; // F0C USB string descriptor len __u8 SerNumDescType; // F0D USB descriptor type (=STRING type) __le16 SerialNumber[MAX_SERIALNUMBER_LEN]; // F0E "01-01-000100" Unicode Serial Number __u8 AssemblyNumLength; // F26 USB string descriptor len __u8 AssemblyNumDescType; // F27 USB descriptor type (=STRING type) __le16 AssemblyNumber[MAX_ASSEMBLYNUMBER_LEN]; // F28 "350-1000-01-A " assembly number __u8 OemAssyNumLength; // F44 USB string descriptor len __u8 OemAssyNumDescType; // F45 USB descriptor type (=STRING type) __le16 OemAssyNumber[MAX_ASSEMBLYNUMBER_LEN]; // F46 "xxxxxxxxxxxxxx" OEM assembly number __u8 ManufDateLength; // F62 USB string descriptor len __u8 ManufDateDescType; // F63 USB descriptor type (=STRING type) __le16 ManufDate[6]; // F64 "MMDDYY" manufacturing date __u8 Reserved3[0x4D]; // F70 -- unused, set to 0 -- __u8 UartType; // FBD Uart Type __u8 IonPid; // FBE Product ID, == LSB of USB DevDesc.PID // (Note: Edgeport/4s before 11/98 will have // 00 here instead of 01) __u8 IonConfig; // FBF Config byte for ION manufacturing use // FBF end of structure, total len = 3C0h }; #define MANUF_DESC_VER_1 1 // Original definition of MANUF_DESC #define MANUF_DESC_VER_2 2 // Ver 2, starts at xC00h len 3C0h // Uart Types // Note: Since this field was added only recently, all Edgeport/4 units // shipped before 11/98 will have 00 in this field. Therefore, // both 00 and 01 values mean '654. #define MANUF_UART_EXAR_654_EARLY 0 // Exar 16C654 in Edgeport/4s before 11/98 #define MANUF_UART_EXAR_654 1 // Exar 16C654 #define MANUF_UART_EXAR_2852 2 // Exar 16C2852 // // Note: The CpuRev and BoardRev values do not conform to manufacturing // revisions; they are to be incremented only when the CPU or hardware // changes in a software-visible way, such that the 930 software or // the host driver needs to handle the hardware differently. // // Values of bottom 5 bits of CpuRev & BoardRev for // Implementation 0 (ie, 930-based) #define MANUF_CPU_REV_AD4 1 // 930 AD4, with EP1 Rx bug (needs RXSPM) #define MANUF_CPU_REV_AD5 2 // 930 AD5, with above bug (supposedly) fixed #define MANUF_CPU_80251 0x20 // Intel 80251 #define MANUF_BOARD_REV_A 1 // Original version, == Manuf Rev A #define MANUF_BOARD_REV_B 2 // Manuf Rev B, wakeup interrupt works #define MANUF_BOARD_REV_C 3 // Manuf Rev C, 2/4 ports, rs232/rs422 #define MANUF_BOARD_REV_GENERATION_2 0x20 // Second generaiton edgeport // Values of bottom 5 bits of CpuRev & BoardRev for // Implementation 1 (ie, 251+Netchip-based) #define MANUF_CPU_REV_1 1 // C251TB Rev 1 (Need actual Intel rev here) #define MANUF_BOARD_REV_A 1 // First rev of 251+Netchip design #define MANUF_SERNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->SerialNumber) #define MANUF_ASSYNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->AssemblyNumber) #define MANUF_OEMASSYNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->OemAssyNumber) #define MANUF_MANUFDATE_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->ManufDate) #define MANUF_ION_CONFIG_DIAG_NO_LOOP 0x20 // As below but no ext loopback test #define MANUF_ION_CONFIG_DIAG 0x40 // 930 based device: 1=Run h/w diags, 0=norm // TIUMP Device : 1=IONSERIAL needs to run Final Test #define MANUF_ION_CONFIG_MASTER 0x80 // 930 based device: 1=Master mode, 0=Normal // TIUMP Device : 1=First device on a multi TIUMP Device // // This structure describes parameters for the boot code, and // is programmed along with new boot code. These are values // which are specific to a given build of the boot code. It // is exactly 64 bytes long and is fixed at address FF:xFC0 // - FF:xFFF. Note that the 930-mandated UCONFIG bytes are // included in this structure. // struct edge_boot_descriptor { __u8 Length; // C0 Desc length, per USB (= 40h) __u8 DescType; // C1 Desc type, per USB (= DEVICE type) __u8 DescVer; // C2 Desc version/format __u8 Reserved1; // C3 -- unused, set to 0 -- __le16 BootCodeLength; // C4 Boot code goes from FF:0000 to FF:(len-1) // (LE format) __u8 MajorVersion; // C6 Firmware version: xx. __u8 MinorVersion; // C7 yy. __le16 BuildNumber; // C8 zzzz (LE format) __u16 EnumRootDescTable; // CA Root of ROM-based descriptor table __u8 NumDescTypes; // CC Number of supported descriptor types __u8 Reserved4; // CD Fix Compiler Packing __le16 Capabilities; // CE-CF Capabilities flags (LE format) __u8 Reserved2[0x28]; // D0 -- unused, set to 0 -- __u8 UConfig0; // F8 930-defined CPU configuration byte 0 __u8 UConfig1; // F9 930-defined CPU configuration byte 1 __u8 Reserved3[6]; // FA -- unused, set to 0 -- // FF end of structure, total len = 80 }; #define BOOT_DESC_VER_1 1 // Original definition of BOOT_PARAMS #define BOOT_DESC_VER_2 2 // 2nd definition, descriptors not included in boot // Capabilities flags #define BOOT_CAP_RESET_CMD 0x0001 // If set, boot correctly supports ION_RESET_DEVICE /************************************************************************ T I U M P D E F I N I T I O N S ***********************************************************************/ // Chip definitions in I2C #define UMP5152 0x52 #define UMP3410 0x10 //************************************************************************ // TI I2C Format Definitions //************************************************************************ #define I2C_DESC_TYPE_INFO_BASIC 0x01 #define I2C_DESC_TYPE_FIRMWARE_BASIC 0x02 #define I2C_DESC_TYPE_DEVICE 0x03 #define I2C_DESC_TYPE_CONFIG 0x04 #define I2C_DESC_TYPE_STRING 0x05 #define I2C_DESC_TYPE_FIRMWARE_AUTO 0x07 // for 3410 download #define I2C_DESC_TYPE_CONFIG_KLUDGE 0x14 // for 3410 #define I2C_DESC_TYPE_WATCHPORT_VERSION 0x15 // firmware version number for watchport #define I2C_DESC_TYPE_WATCHPORT_CALIBRATION_DATA 0x16 // Watchport Calibration Data #define I2C_DESC_TYPE_FIRMWARE_BLANK 0xf2 // Special section defined by ION #define I2C_DESC_TYPE_ION 0 // Not defined by TI struct ti_i2c_desc { __u8 Type; // Type of descriptor __le16 Size; // Size of data only not including header __u8 CheckSum; // Checksum (8 bit sum of data only) __u8 Data[0]; // Data starts here } __attribute__((packed)); // for 5152 devices only (type 2 record) // for 3410 the version is stored in the WATCHPORT_FIRMWARE_VERSION descriptor struct ti_i2c_firmware_rec { __u8 Ver_Major; // Firmware Major version number __u8 Ver_Minor; // Firmware Minor version number __u8 Data[0]; // Download starts here } __attribute__((packed)); struct watchport_firmware_version { // Added 2 bytes for version number __u8 Version_Major; // Download Version (for Watchport) __u8 Version_Minor; } __attribute__((packed)); // Structure of header of download image in fw_down.h struct ti_i2c_image_header { __le16 Length; __u8 CheckSum; } __attribute__((packed)); struct ti_basic_descriptor { __u8 Power; // Self powered // bit 7: 1 - power switching supported // 0 - power switching not supported // // bit 0: 1 - self powered // 0 - bus powered // // __u16 HubVid; // VID HUB __u16 HubPid; // PID HUB __u16 DevPid; // PID Edgeport __u8 HubTime; // Time for power on to power good __u8 HubCurrent; // HUB Current = 100ma } __attribute__((packed)); // CPU / Board Rev Definitions #define TI_CPU_REV_5052 2 // 5052 based edgeports #define TI_CPU_REV_3410 3 // 3410 based edgeports #define TI_BOARD_REV_TI_EP 0 // Basic ti based edgeport #define TI_BOARD_REV_COMPACT 1 // Compact board #define TI_BOARD_REV_WATCHPORT 2 // Watchport #define TI_GET_CPU_REVISION(x) (__u8)((((x)>>4)&0x0f)) #define TI_GET_BOARD_REVISION(x) (__u8)(((x)&0x0f)) #define TI_I2C_SIZE_MASK 0x1f // 5 bits #define TI_GET_I2C_SIZE(x) ((((x) & TI_I2C_SIZE_MASK)+1)*256) #define TI_MAX_I2C_SIZE (16 * 1024) #define TI_MANUF_VERSION_0 0 // IonConig2 flags #define TI_CONFIG2_RS232 0x01 #define TI_CONFIG2_RS422 0x02 #define TI_CONFIG2_RS485 0x04 #define TI_CONFIG2_SWITCHABLE 0x08 #define TI_CONFIG2_WATCHPORT 0x10 struct edge_ti_manuf_descriptor { __u8 IonConfig; // Config byte for ION manufacturing use __u8 IonConfig2; // Expansion __u8 Version; // Version __u8 CpuRev_BoardRev; // CPU revision level (0xF0) and Board Rev Level (0x0F) __u8 NumPorts; // Number of ports for this UMP __u8 NumVirtualPorts; // Number of Virtual ports __u8 HubConfig1; // Used to configure the Hub __u8 HubConfig2; // Used to configure the Hub __u8 TotalPorts; // Total Number of Com Ports for the entire device (All UMPs) __u8 Reserved; // Reserved } __attribute__((packed)); #endif // if !defined(_USBVEND_H)