/* * pata_hpt3x3 - HPT3x3 driver * (c) Copyright 2005-2006 Red Hat * * Was pata_hpt34x but the naming was confusing as it supported the * 343 and 363 so it has been renamed. * * Based on: * linux/drivers/ide/pci/hpt34x.c Version 0.40 Sept 10, 2002 * Copyright (C) 1998-2000 Andre Hedrick * * May be copied or modified under the terms of the GNU General Public * License */ #include #include #include #include #include #include #include #include #define DRV_NAME "pata_hpt3x3" #define DRV_VERSION "0.6.1" /** * hpt3x3_set_piomode - PIO setup * @ap: ATA interface * @adev: device on the interface * * Set our PIO requirements. This is fairly simple on the HPT3x3 as * all we have to do is clear the MWDMA and UDMA bits then load the * mode number. */ static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u32 r1, r2; int dn = 2 * ap->port_no + adev->devno; pci_read_config_dword(pdev, 0x44, &r1); pci_read_config_dword(pdev, 0x48, &r2); /* Load the PIO timing number */ r1 &= ~(7 << (3 * dn)); r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn); r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ pci_write_config_dword(pdev, 0x44, r1); pci_write_config_dword(pdev, 0x48, r2); } #if defined(CONFIG_PATA_HPT3X3_DMA) /** * hpt3x3_set_dmamode - DMA timing setup * @ap: ATA interface * @adev: Device being configured * * Set up the channel for MWDMA or UDMA modes. Much the same as with * PIO, load the mode number and then set MWDMA or UDMA flag. * * 0x44 : bit 0-2 master mode, 3-5 slave mode, etc * 0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc */ static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u32 r1, r2; int dn = 2 * ap->port_no + adev->devno; int mode_num = adev->dma_mode & 0x0F; pci_read_config_dword(pdev, 0x44, &r1); pci_read_config_dword(pdev, 0x48, &r2); /* Load the timing number */ r1 &= ~(7 << (3 * dn)); r1 |= (mode_num << (3 * dn)); r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ if (adev->dma_mode >= XFER_UDMA_0) r2 |= (0x01 << dn); /* Ultra mode */ else r2 |= (0x10 << dn); /* MWDMA */ pci_write_config_dword(pdev, 0x44, r1); pci_write_config_dword(pdev, 0x48, r2); } /** * hpt3x3_freeze - DMA workaround * @ap: port to freeze * * When freezing an HPT3x3 we must stop any pending DMA before * writing to the control register or the chip will hang */ static void hpt3x3_freeze(struct ata_port *ap) { void __iomem *mmio = ap->ioaddr.bmdma_addr; iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ ATA_DMA_START, mmio + ATA_DMA_CMD); ata_sff_dma_pause(ap); ata_sff_freeze(ap); } /** * hpt3x3_bmdma_setup - DMA workaround * @qc: Queued command * * When issuing BMDMA we must clean up the error/active bits in * software on this device */ static void hpt3x3_bmdma_setup(struct ata_queued_cmd *qc) { struct ata_port *ap = qc->ap; u8 r = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); r |= ATA_DMA_INTR | ATA_DMA_ERR; iowrite8(r, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); return ata_bmdma_setup(qc); } /** * hpt3x3_atapi_dma - ATAPI DMA check * @qc: Queued command * * Just say no - we don't do ATAPI DMA */ static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc) { return 1; } #endif /* CONFIG_PATA_HPT3X3_DMA */ static struct scsi_host_template hpt3x3_sht = { ATA_BMDMA_SHT(DRV_NAME), }; static struct ata_port_operations hpt3x3_port_ops = { .inherits = &ata_bmdma_port_ops, .cable_detect = ata_cable_40wire, .set_piomode = hpt3x3_set_piomode, #if defined(CONFIG_PATA_HPT3X3_DMA) .set_dmamode = hpt3x3_set_dmamode, .bmdma_setup = hpt3x3_bmdma_setup, .check_atapi_dma= hpt3x3_atapi_dma, .freeze = hpt3x3_freeze, #endif }; /** * hpt3x3_init_chipset - chip setup * @dev: PCI device * * Perform the setup required at boot and on resume. */ static void hpt3x3_init_chipset(struct pci_dev *dev) { u16 cmd; /* Initialize the board */ pci_write_config_word(dev, 0x80, 0x00); /* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */ pci_read_config_word(dev, PCI_COMMAND, &cmd); if (cmd & PCI_COMMAND_MEMORY) pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0); else pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20); } /** * hpt3x3_init_one - Initialise an HPT343/363 * @pdev: PCI device * @id: Entry in match table * * Perform basic initialisation. We set the device up so we access all * ports via BAR4. This is necessary to work around errata. */ static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id) { static const struct ata_port_info info = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, #if defined(CONFIG_PATA_HPT3X3_DMA) /* Further debug needed */ .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA2, #endif .port_ops = &hpt3x3_port_ops }; /* Register offsets of taskfiles in BAR4 area */ static const u8 offset_cmd[2] = { 0x20, 0x28 }; static const u8 offset_ctl[2] = { 0x36, 0x3E }; const struct ata_port_info *ppi[] = { &info, NULL }; struct ata_host *host; int i, rc; void __iomem *base; hpt3x3_init_chipset(pdev); ata_print_version_once(&pdev->dev, DRV_VERSION); host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2); if (!host) return -ENOMEM; /* acquire resources and fill host */ rc = pcim_enable_device(pdev); if (rc) return rc; /* Everything is relative to BAR4 if we set up this way */ rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME); if (rc == -EBUSY) pcim_pin_device(pdev); if (rc) return rc; host->iomap = pcim_iomap_table(pdev); rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); if (rc) return rc; rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); if (rc) return rc; base = host->iomap[4]; /* Bus mastering base */ for (i = 0; i < host->n_ports; i++) { struct ata_port *ap = host->ports[i]; struct ata_ioports *ioaddr = &ap->ioaddr; ioaddr->cmd_addr = base + offset_cmd[i]; ioaddr->altstatus_addr = ioaddr->ctl_addr = base + offset_ctl[i]; ioaddr->scr_addr = NULL; ata_sff_std_ports(ioaddr); ioaddr->bmdma_addr = base + 8 * i; ata_port_pbar_desc(ap, 4, -1, "ioport"); ata_port_pbar_desc(ap, 4, offset_cmd[i], "cmd"); } pci_set_master(pdev); return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt, IRQF_SHARED, &hpt3x3_sht); } #ifdef CONFIG_PM static int hpt3x3_reinit_one(struct pci_dev *dev) { struct ata_host *host = dev_get_drvdata(&dev->dev); int rc; rc = ata_pci_device_do_resume(dev); if (rc) return rc; hpt3x3_init_chipset(dev); ata_host_resume(host); return 0; } #endif static const struct pci_device_id hpt3x3[] = { { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), }, { }, }; static struct pci_driver hpt3x3_pci_driver = { .name = DRV_NAME, .id_table = hpt3x3, .probe = hpt3x3_init_one, .remove = ata_pci_remove_one, #ifdef CONFIG_PM .suspend = ata_pci_device_suspend, .resume = hpt3x3_reinit_one, #endif }; module_pci_driver(hpt3x3_pci_driver); MODULE_AUTHOR("Alan Cox"); MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363"); MODULE_LICENSE("GPL"); MODULE_DEVICE_TABLE(pci, hpt3x3); MODULE_VERSION(DRV_VERSION);