/* linux/arch/arm/plat-s3c/include/plat/gpio-cfg.h * * Copyright 2008 Openmoko, Inc. * Copyright 2008 Simtec Electronics * http://armlinux.simtec.co.uk/ * Ben Dooks * * S3C Platform - GPIO pin configuration * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ /* This file contains the necessary definitions to get the basic gpio * pin configuration done such as setting a pin to input or output or * changing the pull-{up,down} configurations. */ /* Note, this interface is being added to the s3c64xx arch first and will * be added to the s3c24xx systems later. */ #ifndef __PLAT_GPIO_CFG_H #define __PLAT_GPIO_CFG_H __FILE__ #include typedef unsigned int __bitwise__ samsung_gpio_pull_t; typedef unsigned int __bitwise__ s5p_gpio_drvstr_t; /* forward declaration if gpio-core.h hasn't been included */ struct samsung_gpio_chip; /** * struct samsung_gpio_cfg GPIO configuration * @cfg_eint: Configuration setting when used for external interrupt source * @get_pull: Read the current pull configuration for the GPIO * @set_pull: Set the current pull configuraiton for the GPIO * @set_config: Set the current configuration for the GPIO * @get_config: Read the current configuration for the GPIO * * Each chip can have more than one type of GPIO bank available and some * have different capabilites even when they have the same control register * layouts. Provide an point to vector control routine and provide any * per-bank configuration information that other systems such as the * external interrupt code will need. * * @sa samsung_gpio_cfgpin * @sa s3c_gpio_getcfg * @sa s3c_gpio_setpull * @sa s3c_gpio_getpull */ struct samsung_gpio_cfg { unsigned int cfg_eint; samsung_gpio_pull_t (*get_pull)(struct samsung_gpio_chip *chip, unsigned offs); int (*set_pull)(struct samsung_gpio_chip *chip, unsigned offs, samsung_gpio_pull_t pull); unsigned (*get_config)(struct samsung_gpio_chip *chip, unsigned offs); int (*set_config)(struct samsung_gpio_chip *chip, unsigned offs, unsigned config); }; #define S3C_GPIO_SPECIAL_MARK (0xfffffff0) #define S3C_GPIO_SPECIAL(x) (S3C_GPIO_SPECIAL_MARK | (x)) /* Defines for generic pin configurations */ #define S3C_GPIO_INPUT (S3C_GPIO_SPECIAL(0)) #define S3C_GPIO_OUTPUT (S3C_GPIO_SPECIAL(1)) #define S3C_GPIO_SFN(x) (S3C_GPIO_SPECIAL(x)) #define samsung_gpio_is_cfg_special(_cfg) \ (((_cfg) & S3C_GPIO_SPECIAL_MARK) == S3C_GPIO_SPECIAL_MARK) /** * s3c_gpio_cfgpin() - Change the GPIO function of a pin. * @pin pin The pin number to configure. * @to to The configuration for the pin's function. * * Configure which function is actually connected to the external * pin, such as an gpio input, output or some form of special function * connected to an internal peripheral block. * * The @to parameter can be one of the generic S3C_GPIO_INPUT, S3C_GPIO_OUTPUT * or S3C_GPIO_SFN() to indicate one of the possible values that the helper * will then generate the correct bit mask and shift for the configuration. * * If a bank of GPIOs all needs to be set to special-function 2, then * the following code will work: * * for (gpio = start; gpio < end; gpio++) * s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2)); * * The @to parameter can also be a specific value already shifted to the * correct position in the control register, although these are discouraged * in newer kernels and are only being kept for compatibility. */ extern int s3c_gpio_cfgpin(unsigned int pin, unsigned int to); /** * s3c_gpio_getcfg - Read the current function for a GPIO pin * @pin: The pin to read the configuration value for. * * Read the configuration state of the given @pin, returning a value that * could be passed back to s3c_gpio_cfgpin(). * * @sa s3c_gpio_cfgpin */ extern unsigned s3c_gpio_getcfg(unsigned int pin); /** * s3c_gpio_cfgpin_range() - Change the GPIO function for configuring pin range * @start: The pin number to start at * @nr: The number of pins to configure from @start. * @cfg: The configuration for the pin's function * * Call s3c_gpio_cfgpin() for the @nr pins starting at @start. * * @sa s3c_gpio_cfgpin. */ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr, unsigned int cfg); /* Define values for the pull-{up,down} available for each gpio pin. * * These values control the state of the weak pull-{up,down} resistors * available on most pins on the S3C series. Not all chips support both * up or down settings, and it may be dependent on the chip that is being * used to whether the particular mode is available. */ #define S3C_GPIO_PULL_NONE ((__force samsung_gpio_pull_t)0x00) #define S3C_GPIO_PULL_DOWN ((__force samsung_gpio_pull_t)0x01) #define S3C_GPIO_PULL_UP ((__force samsung_gpio_pull_t)0x02) /** * s3c_gpio_setpull() - set the state of a gpio pin pull resistor * @pin: The pin number to configure the pull resistor. * @pull: The configuration for the pull resistor. * * This function sets the state of the pull-{up,down} resistor for the * specified pin. It will return 0 if successful, or a negative error * code if the pin cannot support the requested pull setting. * * @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP. */ extern int s3c_gpio_setpull(unsigned int pin, samsung_gpio_pull_t pull); /** * s3c_gpio_getpull() - get the pull resistor state of a gpio pin * @pin: The pin number to get the settings for * * Read the pull resistor value for the specified pin. */ extern samsung_gpio_pull_t s3c_gpio_getpull(unsigned int pin); /* configure `all` aspects of an gpio */ /** * s3c_gpio_cfgall_range() - configure range of gpio functtion and pull. * @start: The gpio number to start at. * @nr: The number of gpio to configure from @start. * @cfg: The configuration to use * @pull: The pull setting to use. * * Run s3c_gpio_cfgpin() and s3c_gpio_setpull() over the gpio range starting * @gpio and running for @size. * * @sa s3c_gpio_cfgpin * @sa s3c_gpio_setpull * @sa s3c_gpio_cfgpin_range */ extern int s3c_gpio_cfgall_range(unsigned int start, unsigned int nr, unsigned int cfg, samsung_gpio_pull_t pull); static inline int s3c_gpio_cfgrange_nopull(unsigned int pin, unsigned int size, unsigned int cfg) { return s3c_gpio_cfgall_range(pin, size, cfg, S3C_GPIO_PULL_NONE); } /* Define values for the drvstr available for each gpio pin. * * These values control the value of the output signal driver strength, * configurable on most pins on the S5P series. */ #define S5P_GPIO_DRVSTR_LV1 ((__force s5p_gpio_drvstr_t)0x0) #define S5P_GPIO_DRVSTR_LV2 ((__force s5p_gpio_drvstr_t)0x2) #define S5P_GPIO_DRVSTR_LV3 ((__force s5p_gpio_drvstr_t)0x1) #define S5P_GPIO_DRVSTR_LV4 ((__force s5p_gpio_drvstr_t)0x3) /** * s5c_gpio_get_drvstr() - get the driver streght value of a gpio pin * @pin: The pin number to get the settings for * * Read the driver streght value for the specified pin. */ extern s5p_gpio_drvstr_t s5p_gpio_get_drvstr(unsigned int pin); /** * s3c_gpio_set_drvstr() - set the driver streght value of a gpio pin * @pin: The pin number to configure the driver streght value * @drvstr: The new value of the driver strength * * This function sets the driver strength value for the specified pin. * It will return 0 if successful, or a negative error code if the pin * cannot support the requested setting. */ extern int s5p_gpio_set_drvstr(unsigned int pin, s5p_gpio_drvstr_t drvstr); /** * s5p_register_gpio_interrupt() - register interrupt support for a gpio group * @pin: The pin number from the group to be registered * * This function registers gpio interrupt support for the group that the * specified pin belongs to. * * The total number of gpio pins is quite large ob s5p series. Registering * irq support for all of them would be a resource waste. Because of that the * interrupt support for standard gpio pins is registered dynamically. * * It will return the irq number of the interrupt that has been registered * or -ENOMEM if no more gpio interrupts can be registered. It is allowed * to call this function more than once for the same gpio group (the group * will be registered only once). */ extern int s5p_register_gpio_interrupt(int pin); /** s5p_register_gpioint_bank() - add gpio bank for further gpio interrupt * registration (see s5p_register_gpio_interrupt function) * @chain_irq: chained irq number for the gpio int handler for this bank * @start: start gpio group number of this bank * @nr_groups: number of gpio groups handled by this bank * * This functions registers initial information about gpio banks that * can be later used by the s5p_register_gpio_interrupt() function to * enable support for gpio interrupt for particular gpio group. */ #ifdef CONFIG_S5P_GPIO_INT extern int s5p_register_gpioint_bank(int chain_irq, int start, int nr_groups); #else #define s5p_register_gpioint_bank(chain_irq, start, nr_groups) do { } while (0) #endif #endif /* __PLAT_GPIO_CFG_H */