aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2017-03-12can: usb_8dev: Fix memory leak of priv->cmd_msg_bufferMarc Kleine-Budde
commit 7c42631376306fb3f34d51fda546b50a9b6dd6ec upstream. The priv->cmd_msg_buffer is allocated in the probe function, but never kfree()ed. This patch converts the kzalloc() to resource-managed kzalloc. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-12ath9k: use correct OTP register offsets for the AR9340 and AR9550Christian Lamparter
commit c9f1e32600816d695f817477d56490bfc2ba43c6 upstream. This patch fixes the OTP register definitions for the AR934x and AR9550 WMAC SoC. Previously, the ath9k driver was unable to initialize the integrated WMAC on an Aerohive AP121: | ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004 | ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004 | ath: phy0: Unable to initialize hardware; initialization status: -5 | ath9k ar934x_wmac: failed to initialize device | ath9k: probe of ar934x_wmac failed with error -5 It turns out that the AR9300_OTP_STATUS and AR9300_OTP_DATA definitions contain a typo. Cc: Gabor Juhos <juhosg@openwrt.org> Fixes: add295a4afbdf5852d0 "ath9k: use correct OTP register offsets for AR9550" Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-12ath9k: fix race condition in enabling/disabling IRQsFelix Fietkau
commit 3a5e969bb2f6692a256352649355d56d018d6b88 upstream. The code currently relies on refcounting to disable IRQs from within the IRQ handler and re-enabling them again after the tasklet has run. However, due to race conditions sometimes the IRQ handler might be called twice, or the tasklet may not run at all (if interrupted in the middle of a reset). This can cause nasty imbalances in the irq-disable refcount which will get the driver permanently stuck until the entire radio has been stopped and started again (ath_reset will not recover from this). Instead of using this fragile logic, change the code to ensure that running the irq handler during tasklet processing is safe, and leave the refcount untouched. Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-12ath5k: drop bogus warning on drv_set_key with unsupported cipherFelix Fietkau
commit a70e1d6fd6b5e1a81fa6171600942bee34f5128f upstream. Simply return -EOPNOTSUPP instead. Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-26rtlwifi: rtl_usb: Fix for URB leaking when doing ifconfig up/downMichael Schenk
commit 575ddce0507789bf9830d089557d2199d2f91865 upstream. In the function rtl_usb_start we pre-allocate a certain number of urbs for RX path but they will not be freed when calling rtl_usb_stop. This results in leaking urbs when doing ifconfig up and down. Eventually, the system has no available urbs. Signed-off-by: Michael Schenk <michael.schenk@albis-elcon.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-26rtlwifi: rtl_usb: Fix missing entry in USB driver's private dataLarry Finger
commit 60f59ce0278557f7896d5158ae6d12a4855a72cc upstream. These drivers need to be able to reference "struct ieee80211_hw" from the driver's private data, and vice versa. The USB driver failed to store the address of ieee80211_hw in the private data. Although this bug has been present for a long time, it was not exposed until commit ba9f93f82aba ("rtlwifi: Fix enter/exit power_save"). Fixes: ba9f93f82aba ("rtlwifi: Fix enter/exit power_save") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-18net: introduce device min_header_lenWillem de Bruijn
[ Upstream commit 217e6fa24ce28ec87fca8da93c9016cb78028612 ] The stack must not pass packets to device drivers that are shorter than the minimum link layer header length. Previously, packet sockets would drop packets smaller than or equal to dev->hard_header_len, but this has false positives. Zero length payload is used over Ethernet. Other link layer protocols support variable length headers. Support for validation of these protocols removed the min length check for all protocols. Introduce an explicit dev->min_header_len parameter and drop all packets below this value. Initially, set it to non-zero only for Ethernet and loopback. Other protocols can follow in a patch to net-next. Fixes: 9ed988cd5915 ("packet: validate variable length ll headers") Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-18mlx4: Invoke softirqs after napi_rescheduleBenjamin Poirier
[ Upstream commit bd4ce941c8d5b862b2f83364be5dbe8fc8ab48f8 ] mlx4 may schedule napi from a workqueue. Afterwards, softirqs are not run in a deterministic time frame and the following message may be logged: NOHZ: local_softirq_pending 08 The problem is the same as what was described in commit ec13ee80145c ("virtio_net: invoke softirqs after __napi_schedule") and this patch applies the same fix to mlx4. Fixes: 07841f9d94c1 ("net/mlx4_en: Schedule napi when RX buffers allocation fails") Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-18macvtap: read vnet_hdr_size onceWillem de Bruijn
[ Upstream commit 837585a5375c38d40361cfe64e6fd11e1addb936 ] When IFF_VNET_HDR is enabled, a virtio_net header must precede data. Data length is verified to be greater than or equal to expected header length tun->vnet_hdr_sz before copying. Macvtap functions read the value once, but unless READ_ONCE is used, the compiler may ignore this and read multiple times. Enforce a single read and locally cached value to avoid updates between test and use. Signed-off-by: Willem de Bruijn <willemb@google.com> Suggested-by: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-18tun: read vnet_hdr_sz onceWillem de Bruijn
[ Upstream commit e1edab87faf6ca30cd137e0795bc73aa9a9a22ec ] When IFF_VNET_HDR is enabled, a virtio_net header must precede data. Data length is verified to be greater than or equal to expected header length tun->vnet_hdr_sz before copying. Read this value once and cache locally, as it can be updated between the test and use (TOCTOU). Signed-off-by: Willem de Bruijn <willemb@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> CC: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()Boris Ostrovsky
commit 74470954857c264168d2b5a113904cf0cfd27d18 upstream. rx_refill_timer should be deleted as soon as we disconnect from the backend since otherwise it is possible for the timer to go off before we get to xennet_destroy_queues(). If this happens we may dereference queue->rx.sring which is set to NULL in xennet_disconnect_backend(). Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14netvsc: Set maximum GSO size in the right placeBen Hutchings
Commit a50af86dd49e "netvsc: reduce maximum GSO size" was wrongly backported to 4.4-stable. The maximum size needs to be set before the net device is registered, in netvsc_probe(). Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14hns: avoid stack overflow with CONFIG_KASANArnd Bergmann
commit b3f2d07f4649adcf6905953a10d217b5683e4077 upstream. The use of ACCESS_ONCE() looks like a micro-optimization to force gcc to use an indexed load for the register address, but it has an absolutely detrimental effect on builds with gcc-5 and CONFIG_KASAN=y, leading to a very likely kernel stack overflow aside from very complex object code: hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_update_stats': hisilicon/hns/hns_dsaf_gmac.c:419:1: error: the frame size of 2912 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_reset_common': hisilicon/hns/hns_dsaf_ppe.c:390:1: error: the frame size of 1184 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_get_regs': hisilicon/hns/hns_dsaf_ppe.c:621:1: error: the frame size of 3632 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_common_regs': hisilicon/hns/hns_dsaf_rcb.c:970:1: error: the frame size of 2784 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_get_regs': hisilicon/hns/hns_dsaf_gmac.c:641:1: error: the frame size of 5728 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_ring_regs': hisilicon/hns/hns_dsaf_rcb.c:1021:1: error: the frame size of 2208 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_comm_init': hisilicon/hns/hns_dsaf_main.c:1209:1: error: the frame size of 1904 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_xgmac.c: In function 'hns_xgmac_get_regs': hisilicon/hns/hns_dsaf_xgmac.c:748:1: error: the frame size of 4704 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_update_stats': hisilicon/hns/hns_dsaf_main.c:2420:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_regs': hisilicon/hns/hns_dsaf_main.c:2753:1: error: the frame size of 10768 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] This does not seem to happen any more with gcc-7, but removing the ACCESS_ONCE seems safe anyway and it avoids a serious issue for some people. I have verified that with gcc-5.3.1, the object code we get is better in the new version both with and without CONFIG_KASAN, as we no longer allocate a 1344 byte stack frame for hns_dsaf_get_regs() but otherwise have practically identical object code. With gcc-7.0.0, removing ACCESS_ONCE has no effect, the object code is already good either way. This patch is probably not urgent to get into 4.11 as only KASAN=y builds with certain compilers are affected, but I still think it makes sense to backport into older kernels. Fixes: 511e6bc ("net: add Hisilicon Network Subsystem DSAF support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04qmi_wwan/cdc_ether: add device ID for HP lt2523 (Novatel E371) WWAN cardBjørn Mork
[ Upstream commit 5b9f57516337b523f7466a53939aaaea7b78141b ] Another rebranded Novatel E371. qmi_wwan should drive this device, while cdc_ether should ignore it. Even though the USB descriptors are plain CDC-ETHER that USB interface is a QMI interface. Ref commit 7fdb7846c9ca ("qmi_wwan/cdc_ether: add device IDs for Dell 5804 (Novatel E371) WWAN card") Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04r8152: don't execute runtime suspend if the tx is not emptyhayeswang
[ Upstream commit 6a0b76c04ec157c88ca943debf78a8ee58469f2d ] Runtime suspend shouldn't be executed if the tx queue is not empty, because the device is not idle. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04net: phy: bcm63xx: Utilize correct config_intr functionDaniel Gonzalez Cabanelas
[ Upstream commit cd33b3e0da43522ff8e8f2b2b71d3d08298512b0 ] Commit a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces") make the BCM63xx PHY driver utilize bcm_phy_config_intr() which would appear to do the right thing, except that it does not write to the MII_BCM63XX_IR register but to MII_BCM54XX_ECR which is different. This would be causing invalid link parameters and events from being generated by the PHY interrupt. Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces") Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04ravb: do not use zero-length alignment DMA descriptorMasaru Nagai
[ Upstream commit 8ec3e8a192ba6f13be4522ee81227c792c86fb1a ] Due to alignment requirements of the hardware transmissions are split into two DMA descriptors, a small padding descriptor of 0 - 3 bytes in length followed by a descriptor for rest of the packet. In the case of IP packets the first descriptor will never be zero due to the way that the stack aligns buffers for IP packets. However, for non-IP packets it may be zero. In that case it has been reported that timeouts occur, presumably because transmission stops at the first zero-length DMA descriptor and thus the packet is not transmitted. However, in my environment a BUG is triggered as follows: [ 20.381417] ------------[ cut here ]------------ [ 20.386054] kernel BUG at lib/swiotlb.c:495! [ 20.390324] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [ 20.395805] Modules linked in: [ 20.398862] CPU: 0 PID: 2089 Comm: mz Not tainted 4.10.0-rc3-00001-gf13ad2db193f #162 [ 20.406689] Hardware name: Renesas Salvator-X board based on r8a7796 (DT) [ 20.413474] task: ffff80063b1f1900 task.stack: ffff80063a71c000 [ 20.419404] PC is at swiotlb_tbl_map_single+0x178/0x2ec [ 20.424625] LR is at map_single+0x4c/0x98 [ 20.428629] pc : [<ffff00000839c4c0>] lr : [<ffff00000839c680>] pstate: 800001c5 [ 20.436019] sp : ffff80063a71f9b0 [ 20.439327] x29: ffff80063a71f9b0 x28: ffff80063a20d500 [ 20.444636] x27: ffff000008ed5000 x26: 0000000000000000 [ 20.449944] x25: 000000067abe2adc x24: 0000000000000000 [ 20.455252] x23: 0000000000200000 x22: 0000000000000001 [ 20.460559] x21: 0000000000175ffe x20: ffff80063b2a0010 [ 20.465866] x19: 0000000000000000 x18: 0000ffffcae6fb20 [ 20.471173] x17: 0000ffffa09ba018 x16: ffff0000087c8b70 [ 20.476480] x15: 0000ffffa084f588 x14: 0000ffffa09cfa14 [ 20.481787] x13: 0000ffffcae87ff0 x12: 000000000063abe2 [ 20.487098] x11: ffff000008096360 x10: ffff80063abe2adc [ 20.492407] x9 : 0000000000000000 x8 : 0000000000000000 [ 20.497718] x7 : 0000000000000000 x6 : ffff000008ed50d0 [ 20.503028] x5 : 0000000000000000 x4 : 0000000000000001 [ 20.508338] x3 : 0000000000000000 x2 : 000000067abe2adc [ 20.513648] x1 : 00000000bafff000 x0 : 0000000000000000 [ 20.518958] [ 20.520446] Process mz (pid: 2089, stack limit = 0xffff80063a71c000) [ 20.526798] Stack: (0xffff80063a71f9b0 to 0xffff80063a720000) [ 20.532543] f9a0: ffff80063a71fa30 ffff00000839c680 [ 20.540374] f9c0: ffff80063b2a0010 ffff80063b2a0010 0000000000000001 0000000000000000 [ 20.548204] f9e0: 000000000000006e ffff80063b23c000 ffff80063b23c000 0000000000000000 [ 20.556034] fa00: ffff80063b23c000 ffff80063a20d500 000000013b1f1900 0000000000000000 [ 20.563864] fa20: ffff80063ffd18e0 ffff80063b2a0010 ffff80063a71fa60 ffff00000839cd10 [ 20.571694] fa40: ffff80063b2a0010 0000000000000000 ffff80063ffd18e0 000000067abe2adc [ 20.579524] fa60: ffff80063a71fa90 ffff000008096380 ffff80063b2a0010 0000000000000000 [ 20.587353] fa80: 0000000000000000 0000000000000001 ffff80063a71fac0 ffff00000864f770 [ 20.595184] faa0: ffff80063b23caf0 0000000000000000 0000000000000000 0000000000000140 [ 20.603014] fac0: ffff80063a71fb60 ffff0000087e6498 ffff80063a20d500 ffff80063b23c000 [ 20.610843] fae0: 0000000000000000 ffff000008daeaf0 0000000000000000 ffff000008daeb00 [ 20.618673] fb00: ffff80063a71fc0c ffff000008da7000 ffff80063b23c090 ffff80063a44f000 [ 20.626503] fb20: 0000000000000000 ffff000008daeb00 ffff80063a71fc0c ffff000008da7000 [ 20.634333] fb40: ffff80063b23c090 0000000000000000 ffff800600000037 ffff0000087e63d8 [ 20.642163] fb60: ffff80063a71fbc0 ffff000008807510 ffff80063a692400 ffff80063a20d500 [ 20.649993] fb80: ffff80063a44f000 ffff80063b23c000 ffff80063a69249c 0000000000000000 [ 20.657823] fba0: 0000000000000000 ffff80063a087800 ffff80063b23c000 ffff80063a20d500 [ 20.665653] fbc0: ffff80063a71fc10 ffff0000087e67dc ffff80063a20d500 ffff80063a692400 [ 20.673483] fbe0: ffff80063b23c000 0000000000000000 ffff80063a44f000 ffff80063a69249c [ 20.681312] fc00: ffff80063a5f1a10 000000103a087800 ffff80063a71fc70 ffff0000087e6b24 [ 20.689142] fc20: ffff80063a5f1a80 ffff80063a71fde8 000000000000000f 00000000000005ea [ 20.696972] fc40: ffff80063a5f1a10 0000000000000000 000000000000000f ffff00000887fbd0 [ 20.704802] fc60: fffffff43a5f1a80 0000000000000000 ffff80063a71fc80 ffff000008880240 [ 20.712632] fc80: ffff80063a71fd90 ffff0000087c7a34 ffff80063afc7180 0000000000000000 [ 20.720462] fca0: 0000ffffcae6fe18 0000000000000014 0000000060000000 0000000000000015 [ 20.728292] fcc0: 0000000000000123 00000000000000ce ffff0000088d2000 ffff80063b1f1900 [ 20.736122] fce0: 0000000000008933 ffff000008e7cb80 ffff80063a71fd80 ffff0000087c50a4 [ 20.743951] fd00: 0000000000008933 ffff000008e7cb80 ffff000008e7cb80 000000100000000e [ 20.751781] fd20: ffff80063a71fe4c 0000ffff00000300 0000000000000123 0000000000000000 [ 20.759611] fd40: 0000000000000000 ffff80063b1f0000 000000000000000e 0000000000000300 [ 20.767441] fd60: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 [ 20.775271] fd80: 0000000000000000 0000000000000000 ffff80063a71fda0 ffff0000087c8c20 [ 20.783100] fda0: 0000000000000000 ffff000008082f30 0000000000000000 0000800637260000 [ 20.790930] fdc0: ffffffffffffffff 0000ffffa0903078 0000000000000000 000000001ea87232 [ 20.798760] fde0: 000000000000000f ffff80063a71fe40 ffff800600000014 ffff000000000001 [ 20.806590] fe00: 0000000000000000 0000000000000000 ffff80063a71fde8 0000000000000000 [ 20.814420] fe20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001 [ 20.822249] fe40: 0000000203000011 0000000000000000 0000000000000000 ffff80063a68aa00 [ 20.830079] fe60: ffff80063a68aa00 0000000000000003 0000000000008933 ffff0000081f1b9c [ 20.837909] fe80: 0000000000000000 ffff000008082f30 0000000000000000 0000800637260000 [ 20.845739] fea0: ffffffffffffffff 0000ffffa07ca81c 0000000060000000 0000000000000015 [ 20.853569] fec0: 0000000000000003 000000001ea87232 000000000000000f 0000000000000000 [ 20.861399] fee0: 0000ffffcae6fe18 0000000000000014 0000000000000300 0000000000000000 [ 20.869228] ff00: 00000000000000ce 0000000000000000 00000000ffffffff 0000000000000000 [ 20.877059] ff20: 0000000000000002 0000ffffcae87ff0 0000ffffa09cfa14 0000ffffa084f588 [ 20.884888] ff40: 0000000000000000 0000ffffa09ba018 0000ffffcae6fb20 000000001ea87010 [ 20.892718] ff60: 0000ffffa09b9000 0000ffffcae6fe30 0000ffffcae6fe18 000000000000000f [ 20.900548] ff80: 0000000000000003 000000001ea87232 0000000000000000 0000000000000000 [ 20.908378] ffa0: 0000000000000000 0000ffffcae6fdc0 0000ffffa09a7824 0000ffffcae6fdc0 [ 20.916208] ffc0: 0000ffffa0903078 0000000060000000 0000000000000003 00000000000000ce [ 20.924038] ffe0: 0000000000000000 0000000000000000 ffffffffffffffff ffffffffffffffff [ 20.931867] Call trace: [ 20.934312] Exception stack(0xffff80063a71f7e0 to 0xffff80063a71f910) [ 20.940750] f7e0: 0000000000000000 0001000000000000 ffff80063a71f9b0 ffff00000839c4c0 [ 20.948580] f800: ffff80063a71f840 ffff00000888a6e4 ffff80063a24c418 ffff80063a24c448 [ 20.956410] f820: 0000000000000000 ffff00000811cd54 ffff80063a71f860 ffff80063a24c458 [ 20.964240] f840: ffff80063a71f870 ffff00000888b258 ffff80063a24c418 0000000000000001 [ 20.972070] f860: ffff80063a71f910 ffff80063a7b7028 ffff80063a71f890 ffff0000088825e4 [ 20.979899] f880: 0000000000000000 00000000bafff000 000000067abe2adc 0000000000000000 [ 20.987729] f8a0: 0000000000000001 0000000000000000 ffff000008ed50d0 0000000000000000 [ 20.995560] f8c0: 0000000000000000 0000000000000000 ffff80063abe2adc ffff000008096360 [ 21.003390] f8e0: 000000000063abe2 0000ffffcae87ff0 0000ffffa09cfa14 0000ffffa084f588 [ 21.011219] f900: ffff0000087c8b70 0000ffffa09ba018 [ 21.016097] [<ffff00000839c4c0>] swiotlb_tbl_map_single+0x178/0x2ec [ 21.022362] [<ffff00000839c680>] map_single+0x4c/0x98 [ 21.027411] [<ffff00000839cd10>] swiotlb_map_page+0xa4/0x138 [ 21.033072] [<ffff000008096380>] __swiotlb_map_page+0x20/0x7c [ 21.038821] [<ffff00000864f770>] ravb_start_xmit+0x174/0x668 [ 21.044484] [<ffff0000087e6498>] dev_hard_start_xmit+0x8c/0x120 [ 21.050407] [<ffff000008807510>] sch_direct_xmit+0x108/0x1a0 [ 21.056064] [<ffff0000087e67dc>] __dev_queue_xmit+0x194/0x4cc [ 21.061807] [<ffff0000087e6b24>] dev_queue_xmit+0x10/0x18 [ 21.067214] [<ffff000008880240>] packet_sendmsg+0xf40/0x1220 [ 21.072873] [<ffff0000087c7a34>] sock_sendmsg+0x18/0x2c [ 21.078097] [<ffff0000087c8c20>] SyS_sendto+0xb0/0xf0 [ 21.083150] [<ffff000008082f30>] el0_svc_naked+0x24/0x28 [ 21.088462] Code: d34bfef7 2a1803f3 1a9f86d6 35fff878 (d4210000) [ 21.094611] ---[ end trace 5bc544ad491f3814 ]--- [ 21.099234] Kernel panic - not syncing: Fatal exception in interrupt [ 21.105587] Kernel Offset: disabled [ 21.109073] Memory Limit: none [ 21.112126] ---[ end Kernel panic - not syncing: Fatal exception in interrupt Fixes: 2f45d1902acf ("ravb: minimize TX data copying") Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04net: systemport: Decouple flow control from __bcm_sysport_tx_reclaimFlorian Fainelli
[ Upstream commit 148d3d021cf9724fcf189ce4e525a094bbf5ce89 ] The __bcm_sysport_tx_reclaim() function is used to reclaim transmit resources in different places within the driver. Most of them should not affect the state of the transit flow control. Introduce bcm_sysport_tx_clean() which cleans the ring, but does not re-enable flow control towards the networking stack, and make bcm_sysport_tx_reclaim() do the actual transmit queue flow control. Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04mlxsw: pci: Fix EQE structure definitionElad Raz
[ Upstream commit 28e46a0f2e03ab4ed0e23cace1ea89a68c8c115b ] The event_data starts from address 0x00-0x0C and not from 0x08-0x014. This leads to duplication with other fields in the Event Queue Element such as sub-type, cqn and owner. Fixes: eda6500a987a0 ("mlxsw: Add PCI bus implementation") Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04mlxsw: switchx2: Fix memory leak at skb reallocationArkadi Sharshevsky
[ Upstream commit 400fc0106dd8c27ed84781c929c1a184785b9c79 ] During transmission the skb is checked for headroom in order to add vendor specific header. In case the skb needs to be re-allocated, skb_realloc_headroom() is called to make a private copy of the original, but doesn't release it. Current code assumes that the original skb is released during reallocation and only releases it at the error path which causes a memory leak. Fix this by adding the original skb release to the main path. Fixes: d003462a50de ("mlxsw: Simplify mlxsw_sx_port_xmit function") Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04mlxsw: spectrum: Fix memory leak at skb reallocationArkadi Sharshevsky
[ Upstream commit 36bf38d158d3482119b3e159c0619b3c1539b508 ] During transmission the skb is checked for headroom in order to add vendor specific header. In case the skb needs to be re-allocated, skb_realloc_headroom() is called to make a private copy of the original, but doesn't release it. Current code assumes that the original skb is released during reallocation and only releases it at the error path which causes a memory leak. Fix this by adding the original skb release to the main path. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04r8152: fix the sw rx checksum is unavailablehayeswang
[ Upstream commit 19c0f40d4fca3a47b8f784a627f0467f0138ccc8 ] Fix the hw rx checksum is always enabled, and the user couldn't switch it to sw rx checksum. Note that the RTL_VER_01 only support sw rx checksum only. Besides, the hw rx checksum for RTL_VER_02 is disabled after commit b9a321b48af4 ("r8152: Fix broken RX checksums."). Re-enable it. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-01can: ti_hecc: add missing prepare and unprepare of the clockYegor Yefremov
commit befa60113ce7ea270cb51eada28443ca2756f480 upstream. In order to make the driver work with the common clock framework, this patch converts the clk_enable()/clk_disable() to clk_prepare_enable()/clk_disable_unprepare(). Also add error checking for clk_prepare_enable(). Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-01can: c_can_pci: fix null-pointer-deref in c_can_start() - set device pointerEinar Jón
commit c97c52be78b8463ac5407f1cf1f22f8f6cf93a37 upstream. The priv->device pointer for c_can_pci is never set, but it is used without a NULL check in c_can_start(). Setting it in c_can_pci_probe() like c_can_plat_probe() prevents c_can_pci.ko from crashing, with and without CONFIG_PM. This might also cause the pm_runtime_*() functions in c_can.c to actually be executed for c_can_pci devices - they are the only other place where priv->device is used, but they all contain a null check. Signed-off-by: Einar Jón <tolvupostur@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-26ieee802154: atusb: do not use the stack for buffers to make them DMA ableStefan Schmidt
commit 05a974efa4bdf6e2a150e3f27dc6fcf0a9ad5655 upstream. From 4.9 we should really avoid using the stack here as this will not be DMA able on various platforms. This changes the buffers already being present in time of 4.9 being released. This should go into stable as well. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15net: vrf: do not allow table id 0David Ahern
[ Upstream commit 24c63bbc18e25d5d8439422aa5fd2d66390b88eb ] Frank reported that vrf devices can be created with a table id of 0. This breaks many of the run time table id checks and should not be allowed. Detect this condition at create time and fail with EINVAL. Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Reported-by: Frank Kellermann <frank.kellermann@atos.net> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15net: ipv4: Fix multipath selection with vrfDavid Ahern
[ Upstream commit 7a18c5b9fb31a999afc62b0e60978aa896fc89e9 ] fib_select_path does not call fib_select_multipath if oif is set in the flow struct. For VRF use cases oif is always set, so multipath route selection is bypassed. Use the FLOWI_FLAG_SKIP_NH_OIF to skip the oif check similar to what is done in fib_table_lookup. Add saddr and proto to the flow struct for the fib lookup done by the VRF driver to better match hash computation for a flow. Fixes: 613d09b30f8b ("net: Use VRF device index for lookups on TX") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15r8152: fix rx issue for runtime suspendhayeswang
[ Upstream commit 75dc692eda114cb234a46cb11893a9c3ea520934 ] Pause the rx and make sure the rx fifo is empty when the autosuspend occurs. If the rx data comes when the driver is canceling the rx urb, the host controller would stop getting the data from the device and continue it after next rx urb is submitted. That is, one continuing data is split into two different urb buffers. That let the driver take the data as a rx descriptor, and unexpected behavior happens. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15r8152: split rtl8152_suspend functionhayeswang
[ Upstream commit 8fb280616878b81c0790a0c33acbeec59c5711f4 ] Split rtl8152_suspend() into rtl8152_system_suspend() and rtl8152_rumtime_suspend(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15net/mlx5: Avoid shadowing numa_nodeEli Cohen
[ Upstream commit d151d73dcc99de87c63bdefebcc4cb69de1cdc40 ] Avoid using a local variable named numa_node to avoid shadowing a public one. Fixes: db058a186f98 ('net/mlx5_core: Set irq affinity hints') Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15net/mlx5: Check FW limitations on log_max_qp before setting itNoa Osherovich
[ Upstream commit 883371c453b937f9eb581fb4915210865982736f ] When setting HCA capabilities, set log_max_qp to be the minimum between the selected profile's value and the HCA limitation. Fixes: 938fe83c8dcb ('net/mlx5_core: New device capabilities...') Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15net: stmmac: Fix race between stmmac_drv_probe and stmmac_openFlorian Fainelli
[ Upstream commit 5701659004d68085182d2fd4199c79172165fa65 ] There is currently a small window during which the network device registered by stmmac can be made visible, yet all resources, including and clock and MDIO bus have not had a chance to be set up, this can lead to the following error to occur: [ 473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized): stmmac_dvr_probe: warning: cannot get CSR clock [ 473.919382] stmmaceth 0000:01:00.0: no reset control found [ 473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42 [ 473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported [ 473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported [ 473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported [ 473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized): Enable RX Mitigation via HW Watchdog Timer [ 473.921395] libphy: PHY stmmac-1:00 not found [ 473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY [ 473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to PHY (error: -19) [ 473.959710] libphy: stmmac: probed [ 473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 0 IRQ POLL (stmmac-1:00) active [ 473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 1 IRQ POLL (stmmac-1:01) [ 473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 2 IRQ POLL (stmmac-1:02) [ 473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 3 IRQ POLL (stmmac-1:03) Fix this by making sure that register_netdev() is the last thing being done, which guarantees that the clock and the MDIO bus are available. Fixes: 4bfcbd7abce2 ("stmmac: Move the mdio_register/_unregister in probe/remove") Reported-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15net: vrf: Drop conntrack data after pass through VRF device on TxDavid Ahern
[ Upstream commit eb63ecc1706b3e094d0f57438b6c2067cfc299f2 ] Locally originated traffic in a VRF fails in the presence of a POSTROUTING rule. For example, $ iptables -t nat -A POSTROUTING -s 11.1.1.0/24 -j MASQUERADE $ ping -I red -c1 11.1.1.3 ping: Warning: source address might be selected on device other than red. PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data. ping: sendmsg: Operation not permitted Worse, the above causes random corruption resulting in a panic in random places (I have not seen a consistent backtrace). Call nf_reset to drop the conntrack info following the pass through the VRF device. The nf_reset is needed on Tx but not Rx because of the order in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress device and on Tx it is is before the real egress device. Connection tracking should be tied to the real egress device and not the VRF device. Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device") Fixes: 35402e3136634 ("net: Add IPv6 support to VRF device") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-15netvsc: reduce maximum GSO sizestephen hemminger
[ Upstream commit a50af86dd49ee1851d1ccf06dd0019c05b95e297 ] Hyper-V (and Azure) support using NVGRE which requires some extra space for encapsulation headers. Because of this the largest allowed TSO packet is reduced. For older releases, hard code a fixed reduced value. For next release, there is a better solution which uses result of host offload negotiation. Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-12net: vxge: avoid unused function warningsArnd Bergmann
commit 57e7c8cef224af166b8ec932b5e383641418c005 upstream. When CONFIG_PCI_MSI is disabled, we get warnings about unused functions in the vxge driver: drivers/net/ethernet/neterion/vxge/vxge-main.c:2121:13: warning: 'adaptive_coalesce_tx_interrupts' defined but not used [-Wunused-function] drivers/net/ethernet/neterion/vxge/vxge-main.c:2149:13: warning: 'adaptive_coalesce_rx_interrupts' defined but not used [-Wunused-function] We could add another #ifdef here, but it's nicer to avoid those warnings for good by converting the existing #ifdef to if(IS_ENABLED()), which has the same effect but provides better compile-time coverage in general, and lets the compiler understand better when the function is intentionally unused. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-12net: ti: cpmac: Fix compiler warning due to type confusionPaul Burton
commit 2f5281ba2a8feaf6f0aee93356f350855bb530fc upstream. cpmac_start_xmit() used the max() macro on skb->len (an unsigned int) and ETH_ZLEN (a signed int literal). This led to the following compiler warning: In file included from include/linux/list.h:8:0, from include/linux/module.h:9, from drivers/net/ethernet/ti/cpmac.c:19: drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_start_xmit': include/linux/kernel.h:748:17: warning: comparison of distinct pointer types lacks a cast (void) (&_max1 == &_max2); \ ^ drivers/net/ethernet/ti/cpmac.c:560:8: note: in expansion of macro 'max' len = max(skb->len, ETH_ZLEN); ^ On top of this, it assigned the result of the max() macro to a signed integer whilst all further uses of it result in it being cast to varying widths of unsigned integer. Fix this up by using max_t to ensure the comparison is performed as unsigned integers, and for consistency change the type of the len variable to unsigned int. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-12ath10k: use the right length of "background"Nicolas Iooss
commit 31b239824ece321c09bdb8e61e1d14814eaba38b upstream. The word "background" contains 10 characters so the third argument of strncmp() need to be 10 in order to match this prefix correctly. Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Fixes: 855aed1220d2 ("ath10k: add spectral scan feature") Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-09net: mvpp2: fix dma unmapping of TX buffers for fragmentsThomas Petazzoni
commit 8354491c9d5b06709384cea91d13019bf5e61449 upstream. Since commit 71ce391dfb784 ("net: mvpp2: enable proper per-CPU TX buffers unmapping"), we are not correctly DMA unmapping TX buffers for fragments. Indeed, the mvpp2_txq_inc_put() function only stores in the txq_cpu->tx_buffs[] array the physical address of the buffer to be DMA-unmapped when skb != NULL. In addition, when DMA-unmapping, we use skb_headlen(skb) to get the size to be unmapped. Both of this works fine for TX descriptors that are associated directly to a SKB, but not the ones that are used for fragments, with a NULL pointer as skb: - We have a NULL physical address when calling DMA unmap - skb_headlen(skb) crashes because skb is NULL This causes random crashes when fragments are used. To solve this problem, we need to: - Store the physical address of the buffer to be unmapped unconditionally, regardless of whether it is tied to a SKB or not. - Store the length of the buffer to be unmapped, which requires a new field. Instead of adding a third array to store the length of the buffer to be unmapped, and as suggested by David Miller, this commit refactors the tx_buffs[] and tx_skb[] arrays of 'struct mvpp2_txq_pcpu' into a separate structure 'mvpp2_txq_pcpu_buf', to which a 'size' field is added. Therefore, instead of having three arrays to allocate/free, we have a single one, which also improve data locality, reducing the impact on the CPU cache. Fixes: 71ce391dfb784 ("net: mvpp2: enable proper per-CPU TX buffers unmapping") Reported-by: Raphael G <raphael.glon@corp.ovh.com> Cc: Raphael G <raphael.glon@corp.ovh.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-09ath9k: Really fix LED polarity for some Mini PCI AR9220 MB92 cards.Vittorio Gambaletta (VittGam)
commit 79e57dd113d307a6c74773b8aaecf5442068988a upstream. The active_high LED of my Wistron DNMA-92 is still being recognized as active_low on 4.7.6 mainline. When I was preparing my former commit 0f9edcdd88a9 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.") to fix that I must have somehow messed up with testing, because I tested the final version of that patch before sending it, and it was apparently working; but now it is not working on 4.7.6 mainline. I initially added the PCI_DEVICE_SUB section for 0x0029/0x2096 above the PCI_VDEVICE section for 0x0029; but then I moved the former below the latter after seeing how 0x002A sections were sorted in the file. This turned out to be wrong: if a generic PCI_VDEVICE entry (that has both subvendor and subdevice IDs set to PCI_ANY_ID) is put before a more specific one (PCI_DEVICE_SUB), then the generic PCI_VDEVICE entry will match first and will be used. With this patch, 0x0029/0x2096 has finally got active_high LED on 4.7.6. While I'm at it, let's fix 0x002A too by also moving its generic definition below its specific ones. Fixes: 0f9edcdd88a9 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.") Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> [kvalo@qca.qualcomm.com: improve the commit log based on email discussions] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-09rtlwifi: Fix enter/exit power_saveLarry Finger
commit ba9f93f82abafe2552eac942ebb11c2df4f8dd7f upstream. In commit a5ffbe0a1993 ("rtlwifi: Fix scheduling while atomic bug") and commit a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue"), an error was introduced in the power-save routines due to the fact that leaving PS was delayed by the use of a work queue. This problem is fixed by detecting if the enter or leave routines are in interrupt mode. If so, the workqueue is used to place the request. If in normal mode, the enter or leave routines are called directly. Fixes: a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Reported-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-06ppp: defer netns reference release for ppp channelWANG Cong
commit 205e1e255c479f3fd77446415706463b282f94e4 upstream. Matt reported that we have a NULL pointer dereference in ppp_pernet() from ppp_connect_channel(), i.e. pch->chan_net is NULL. This is due to that a parallel ppp_unregister_channel() could happen while we are in ppp_connect_channel(), during which pch->chan_net set to NULL. Since we need a reference to net per channel, it makes sense to sync the refcnt with the life time of the channel, therefore we should release this reference when we destroy it. Fixes: 1f461dcdd296 ("ppp: take reference on channels netns") Reported-by: Matt Bennett <Matt.Bennett@alliedtelesis.co.nz> Cc: Paul Mackerras <paulus@samba.org> Cc: linux-ppp@vger.kernel.org Cc: Guillaume Nault <g.nault@alphalink.fr> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: bmajal222 <bmajal222@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-15can: peak: fix bad memory access and free sequence추지호
commit b67d0dd7d0dc9e456825447bbeb935d8ef43ea7c upstream. Fix for bad memory access while disconnecting. netdev is freed before private data free, and dev is accessed after freeing netdev. This makes a slub problem, and it raise kernel oops with slub debugger config. Signed-off-by: Jiho Chu <jiho.chu@samsung.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-10geneve: avoid use-after-free of skb->dataSabrina Dubroca
[ Upstream commit 5b01014759991887b1e450c9def01e58c02ab81b ] geneve{,6}_build_skb can end up doing a pskb_expand_head(), which makes the ip_hdr(skb) reference we stashed earlier stale. Since it's only needed as an argument to ip_tunnel_ecn_encap(), move this directly in the function call. Fixes: 08399efc6319 ("geneve: ensure ECN info is handled properly in all tx/rx paths") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-10sh_eth: remove unchecked interrupts for RZ/A1Chris Brandt
[ Upstream commit 33d446dbba4d4d6a77e1e900d434fa99e0f02c86 ] When streaming a lot of data and the RZ/A1 can't keep up, some status bits will get set that are not being checked or cleared which cause the following messages and the Ethernet driver to stop working. This patch fixes that issue. irq 21: nobody cared (try booting with the "irqpoll" option) handlers: [<c036b71c>] sh_eth_interrupt Disabling IRQ #21 Fixes: db893473d313a4ad ("sh_eth: Add support for r7s72100") Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-10net: bcmgenet: Utilize correct struct device for all DMA operationsFlorian Fainelli
[ Upstream commit 8c4799ac799665065f9bf1364fd71bf4f7dc6a4a ] __bcmgenet_tx_reclaim() and bcmgenet_free_rx_buffers() are not using the same struct device during unmap that was used for the map operation, which makes DMA-API debugging warn about it. Fix this by always using &priv->pdev->dev throughout the driver, using an identical device reference for all map/unmap calls. Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-10net: dsa: bcm_sf2: Ensure we re-negotiate EEE during after link changeFlorian Fainelli
[ Upstream commit 76da8706d90d8641eeb9b8e579942ed80b6c0880 ] In case the link change and EEE is enabled or disabled, always try to re-negotiate this with the link partner. Fixes: 450b05c15f9c ("net: dsa: bcm_sf2: add support for controlling EEE") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-10net: sky2: Fix shutdown crashJeremy Linton
[ Upstream commit 06ba3b2133dc203e1e9bc36cee7f0839b79a9e8b ] The sky2 frequently crashes during machine shutdown with: sky2_get_stats+0x60/0x3d8 [sky2] dev_get_stats+0x68/0xd8 rtnl_fill_stats+0x54/0x140 rtnl_fill_ifinfo+0x46c/0xc68 rtmsg_ifinfo_build_skb+0x7c/0xf0 rtmsg_ifinfo.part.22+0x3c/0x70 rtmsg_ifinfo+0x50/0x5c netdev_state_change+0x4c/0x58 linkwatch_do_dev+0x50/0x88 __linkwatch_run_queue+0x104/0x1a4 linkwatch_event+0x30/0x3c process_one_work+0x140/0x3e0 worker_thread+0x60/0x44c kthread+0xdc/0xf0 ret_from_fork+0x10/0x50 This is caused by the sky2 being called after it has been shutdown. A previous thread about this can be found here: https://lkml.org/lkml/2016/4/12/410 An alternative fix is to assure that IFF_UP gets cleared by calling dev_close() during shutdown. This is similar to what the bnx2/tg3/xgene and maybe others are doing to assure that the driver isn't being called following _shutdown(). Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-10virtio-net: add a missing synchronize_net()Eric Dumazet
[ Upstream commit 963abe5c8a0273a1cf5913556da1b1189de0e57a ] It seems many drivers do not respect napi_hash_del() contract. When napi_hash_del() is used before netif_napi_del(), an RCU grace period is needed before freeing NAPI object. Fixes: 91815639d880 ("virtio-net: rx busy polling support") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-08mwifiex: printk() overflow with 32-byte SSIDsBrian Norris
commit fcd2042e8d36cf644bd2d69c26378d17158b17df upstream. SSIDs aren't guaranteed to be 0-terminated. Let's cap the max length when we print them out. This can be easily noticed by connecting to a network with a 32-octet SSID: [ 3903.502925] mwifiex_pcie 0000:01:00.0: info: trying to associate to '0123456789abcdef0123456789abcdef <uninitialized mem>' bssid xx:xx:xx:xx:xx:xx Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Brian Norris <briannorris@chromium.org> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26iwlwifi: pcie: fix SPLC structure parsingLuca Coelho
commit e0d9727c111a5917a1184c71c1a8e6f78c7fc41d upstream. The SPLC data parsing is too restrictive and was not trying find the correct element for WiFi. This causes problems with some BIOSes where the SPLC method exists, but doesn't have a WiFi entry on the first element of the list. The domain type values are also incorrect according to the specification. Fix this by complying with the actual specification. Additionally, replace all occurrences of SPLX to SPLC, since SPLX is only a structure internal to the ACPI tables, and may not even exist. Fixes: bcb079a14d75 ("iwlwifi: pcie: retrieve and parse ACPI power limitations") Reported-by: Chris Rorvick <chris@rorvick.com> Tested-by: Paul Bolle <pebolle@tiscali.nl> Tested-by: Chris Rorvick <chris@rorvick.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-28 18:57:22 +0000