| Age | Commit message (Collapse) | Author |
|---|
|
qlge driver turns off NETIF_F_HW_CTAG_FILTER, but forgets to
turn off HW_CTAG_TX and HW_CTAG_RX on vlan devices. With the
current settings, q-in-q will only generate a single vlan header.
Remember to mask off CTAG_TX and CTAG_RX features in vlan_features.
CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The second parameter of __mlx4_init_one() is used to identify whether the
pci_dev is a PF or VF. Currently, when it is invoked in mlx4_pci_slot_reset()
this information is missed.
This patch match the pci_dev with mlx4_pci_table and passes the
pci_device_id.driver_data to __mlx4_init_one() in mlx4_pci_slot_reset().
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.
This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5445eaf309ff ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, it turns out that the Armada XP GP, which uses RGMII, is
affected by a similar problem: its SERDES configuration is lost when
mvneta is loaded as a module, because this configuration is set by the
bootloader, and then lost because the clock is gated by the clock
framework until the mvneta driver is loaded again and the clock is
re-enabled.
However, it turns out that for the RGMII case, setting the SERDES
configuration is not sufficient: the PCS enable bit in the
MVNETA_GMAC_CTRL_2 register must also be set, like in the SGMII
configuration.
Therefore, this commit reworks the SGMII/RGMII initialization: the
only difference between the two now is a different SERDES
configuration, all the rest is identical.
In detail, to achieve this, the commit:
* Renames MVNETA_SGMII_SERDES_CFG to MVNETA_SERDES_CFG because it is
not specific to SGMII, but also used on RGMII configurations.
* Adds a MVNETA_RGMII_SERDES_PROTO definition, that must be used as
the MVNETA_SERDES_CFG value in RGMII configurations.
* Removes the mvneta_gmac_rgmii_set() and mvneta_port_sgmii_config()
functions, and instead directly do the SGMII/RGMII configuration in
mvneta_port_up(), from where those functions where called. It is
worth mentioning that mvneta_gmac_rgmii_set() had an 'enable'
parameter that was always passed as '1', so it was pretty useless.
* Reworks the mvneta_port_up() function to set the MVNETA_SERDES_CFG
register to the appropriate value depending on the RGMII vs. SGMII
configuration. It also unconditionally set the PCS_ENABLE bit (was
already done for SGMII, but is now also needed for RGMII), and sets
the PORT_RGMII bit (which was already done for both SGMII and
RGMII).
This commit was successfully tested with mvneta compiled as a module,
on both the OpenBlocks AX3 (SGMII configuration) and the Armada XP GP
(RGMII configuration).
Reported-by: Steve McIntyre <steve@einval.com>
Cc: stable@vger.kernel.org # 3.11.x: 5445eaf309ff mvneta: Try to fix mvneta when compiled as module
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bit 3 of the MVNETA_GMAC_CTRL_2 is actually used to enable the PCS,
not the PSC: there was a typo in the name of the define, which this
commit fixes.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Including hardware acceleration features in vlan_features breaks
stacked vlans (Q-in-Q) by marking the bottom vlan interface as
capable of acceleration. This causes one of the tags to be lost
and the packets are sent with a sing vlan header.
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an error occurs during the initialization in emac_dev_open() (the
driver's ndo_open function), interrupts, DMA descriptors etc. must be freed.
The current rollback code is buggy in several ways.
1) Freeing the interrupts. The current code will not free all interrupts
that were requested by the driver. Furthermore, the code tries to do a
platform_get_resource(priv->pdev, IORESOURCE_IRQ, -1) in its last
iteration.
This patch fixes these bugs.
2) Wrong order of err: and rollback: labels. If the setup of the PHY in
the code fails, the interrupts that have been requested before are
not freed:
request irq
if requesting irqs fails, goto rollback
setup phy
if phy setup fails, goto err
return 0
rollback:
free irqs
err:
This patch brings the code into the correct order.
3) The code calls napi_enable() and emac_int_enable(), but does not
undo both in case of an error.
This patch adds calls of emac_int_disable() and napi_disable() to the
rollback code.
4) RX DMA descriptors are not freed in case of an error: Right before
requesting the irqs, the function creates DMA descriptors for the
RX channel. These RX descriptors are never freed when we jump to either
rollback or err.
This patch adds code for freeing the DMA descriptors in the case of
an initialization error. This required a modification of
cpdma_ctrl_stop() in davinci_cpdma.c: We must be able to call this
function to free the DMA descriptors while the DMA channels are
in IDLE state (before cpdma_ctlr_start() was called).
Tested on a custom board with the Texas Instruments AM1808.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 6892b41d9701283085b655c6086fb57a5d63fa47
Author: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Date: Tue Jun 25 21:24:51 2013 +0530
net: davinci: emac: Convert to devm_* api
the call of request_irq is replaced by devm_request_irq and the call
of free_irq is removed. But since interrupts are requested in
emac_dev_open, doing ifconfig up/down on the board requests the
interrupts again each time, causing devm_request_irq to fail. The
interface is dead until the device is rebooted.
This patch reverts said commit partially: It changes the driver back
to use request_irq instead of devm_request_irq, puts free_irq back in
place, but keeps the remaining changes of the original patch.
Reported-by: Jon Ringle <jon@ringle.org>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.
Fixes: 66fda75f47dc (regulator: core: Replace direct ops->disable usage)
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, via-rhine fails to call pci_disable_device() for errors
in rhine_init_one().
Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use pci_iounmap instead of iounmap when the virtual mapping was done
with pci_iomap. A simplified version of the semantic patch that finds this
issue is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression addr;
@@
addr = pci_iomap(...)
@rr@
expression r.addr;
@@
* iounmap(addr)
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bnx2/bnx2x rings are made up of linked pages. However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface. In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE. On archs with >= 64K PAGE_SIZE, it generates some compile
warnings. Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For per device operations, cnic needs to dereference the RCU protected
cp->ulp_ops instead of the global cnic_ulp_tbl. In 2 locations,
cnic_send_nlmsg() and cnic_copy_ulp_stats(), it was referencing the
global table. If the device has been unregistered and these functions
are still being called (very unlikely scenarios), it could lead to NULL
pointer dereference.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit f280e89a (drivers: net: cpsw: fix for cpsw crash when build as modules)
moved cpts_register()/cpts_unregister() to ndo_open()/ndo_stop(), but failed
to remove cpts_register in cpsw_probe() which leads to a double registration
and the following debug object splat.
[ 18.991902] ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x2c
[ 19.082249] [<c0059e80>] (init_timer_key) from [<c04965d4>] (cpts_register+0x1f0/0x2c4)
[ 19.090642] [<c04965d4>] (cpts_register) from [<c04931dc>] (cpsw_ndo_open+0x780/0x81c)
[ 19.098948] [<c04931dc>] (cpsw_ndo_open) from [<c0599c2c>] (__dev_open+0xb4/0x118)
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. For the 64 bits dma mask use dma_set_mask_and_coherent instead of
dma_set_mask and dma_set_coherent_mask.
2. For the 32 bits dma mask dma_set_coherent_mask is only called if
dma_set_mask fails, which is unusual. Assuming this as a bug, fixes
it by replacing calls to dma_set_mask and dma_set_coherent_mask by a
call to dma_set_mask_and_coherent.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.
This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mlx4_en_stop_port() is called, we need to deregister also the
tunnel steering rules that relate to multicast.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When checking what protocol drivers to load, the IB driver should be
requested also over Ethernet ports, if the device supports IBoE (RoCE).
Fixes: b046ffe 'net/mlx4_core: Load higher level modules according to ports type'
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the device mac address is changed, we must deregister the vxlan
steering rule associated with the previous mac, and register a new
steering rule using the new mac.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the value used to dump the vxlan offloads device capability to align
with the MLX4_DEV_CAP_FLAG2_yyy definition. While on that, add dump to
the IPoIB flow-steering device capability and fix small typo.
The vxlan cap value wasn't fully handled when a conflict was resolved
between MLX4_DEV_CAP_FLAG2_DMFS_IPOIB coming from the IB tree to
MLX4_DEV_CAP_FLAG2_VXLAN_OFFLOADS coming from net-next.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx descriptor version of RTL8111B belong to RTL_TD_0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.
Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
udelay() does not work on some architectures for values above
2000, in particular on ARM:
ERROR: "__bad_udelay" [drivers/net/ethernet/brocade/bna/bna.ko] undefined!
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pci shutdown handler added in:
bnx2: Add pci shutdown handler
commit 25bfb1dd4ba3b2d9a49ce9d9b0cd7be1840e15ed
created a shutdown down sequence without chip reset if the device was
never brought up. This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive. On some
systems, it may generate NMI in the bnx2's pci shutdown handler.
The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ready
Currently, the PF call to pci_enable_sriov from the PF probe function
stalls for 10 seconds times the number of VFs probed on the host. This
happens because the way for such VFs to determine of the PF
initialization finished, is by attempting to issue reset on the
comm-channel and get timeout (after 10s).
The PF probe function is called from a kenernel workqueue, and therefore
during that time, rcu lock is being held and kernel's workqueue is
stalled. This blocks other processes that try to use the workqueue
or rcu lock. For example, interface renaming which is calling
rcu_synchronize is blocked, and timedout by systemd.
Changed mlx4_init_slave() to allow VF probed on the host to immediatly
detect that the PF is not ready, and return EPROBE_DEFER instantly.
Only when the PF finishes the initialization, allow such VFs to
access the comm channel.
This issue and fix are relevant only for probed VFs on the hypervisor,
there is no way to pass this information to a VM until comm channel is
ready, so in a VM, if PF is not ready, the first command will be timedout
after 10 seconds and return EPROBE_DEFER.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a regression introduced by [1]. outbox was accessed instead of
outbox->buf. Typo was copy-pasted to [2] and [3].
[1] - cc1ade9 mlx4_core: Disable memory windows for virtual functions
[2] - 4de6580 mlx4_core: Add support for steerable IB UD QPs
[3] - 7ffdf72 net/mlx4_core: Add basic support for TCP/IP offloads under
tunneling
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code to load a MAC address into a u64 for passing to the
hypervisor via a register is broken on little endian.
Create a helper function called ibmveth_encode_mac_addr
which does the right thing in both big and little endian.
We were storing the MAC address in a long in struct ibmveth_adapter.
It's never used so remove it - we don't need another place in the
driver where we create endian issues with MAC addresses.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When allocating RX buffers a fixed size is used, while freeing is based
on actually received bytes, resulting in the following kernel warning
when CONFIG_DMA_API_DEBUG is enabled:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1051 check_unmap+0x258/0x894()
macb e000b000.ethernet: DMA-API: device driver frees DMA memory with different size [device address=0x000000002d170040] [map size=1536 bytes] [unmap size=60 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.0-rc3-xilinx-00220-g49f84081ce4f #65
[<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
[<c0011df8>] (show_stack) from [<c03c775c>] (dump_stack+0x7c/0xc8)
[<c03c775c>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
[<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
[<c0024670>] (warn_slowpath_fmt) from [<c0227d44>] (check_unmap+0x258/0x894)
[<c0227d44>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
[<c0228588>] (debug_dma_unmap_page) from [<c02ab78c>] (gem_rx+0x118/0x170)
[<c02ab78c>] (gem_rx) from [<c02ac4d4>] (macb_poll+0x24/0x94)
[<c02ac4d4>] (macb_poll) from [<c031222c>] (net_rx_action+0x6c/0x188)
[<c031222c>] (net_rx_action) from [<c0028a28>] (__do_softirq+0x108/0x280)
[<c0028a28>] (__do_softirq) from [<c0028e8c>] (irq_exit+0x84/0xf8)
[<c0028e8c>] (irq_exit) from [<c000f360>] (handle_IRQ+0x68/0x8c)
[<c000f360>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
[<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
Exception stack(0xc056df20 to 0xc056df68)
df20: 00000001 c0577430 00000000 c0577430 04ce8e0d 00000002 edfce238 00000000
df40: 04e20f78 00000002 c05981f4 00000000 00000008 c056df68 c0064008 c02d7658
df60: 20000013 ffffffff
[<c0012904>] (__irq_svc) from [<c02d7658>] (cpuidle_enter_state+0x54/0xf8)
[<c02d7658>] (cpuidle_enter_state) from [<c02d77dc>] (cpuidle_idle_call+0xe0/0x138)
[<c02d77dc>] (cpuidle_idle_call) from [<c000f660>] (arch_cpu_idle+0x8/0x3c)
[<c000f660>] (arch_cpu_idle) from [<c006bec4>] (cpu_startup_entry+0xbc/0x124)
[<c006bec4>] (cpu_startup_entry) from [<c053daec>] (start_kernel+0x350/0x3b0)
---[ end trace d5fdc38641bd3a11 ]---
Mapped at:
[<c0227184>] debug_dma_map_page+0x48/0x11c
[<c02ab32c>] gem_rx_refill+0x154/0x1f8
[<c02ac7b4>] macb_open+0x270/0x3e0
[<c03152e0>] __dev_open+0x7c/0xfc
[<c031554c>] __dev_change_flags+0x8c/0x140
Fixing this by passing the same size which is passed during mapping the
memory to the unmap function as well.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With CONFIG_DMA_API_DEBUG enabled the following warning is printed:
WARNING: CPU: 0 PID: 619 at lib/dma-debug.c:1101 check_unmap+0x758/0x894()
macb e000b000.ethernet: DMA-API: device driver failed to check map error[device address=0x000000002d171c02] [size=322 bytes] [mapped as single]
Modules linked in:
CPU: 0 PID: 619 Comm: udhcpc Not tainted 3.14.0-rc3-xilinx-00219-gd158fc7f36a2 #63
[<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
[<c0011df8>] (show_stack) from [<c03c7714>] (dump_stack+0x7c/0xc8)
[<c03c7714>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
[<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
[<c0024670>] (warn_slowpath_fmt) from [<c0228244>] (check_unmap+0x758/0x894)
[<c0228244>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
[<c0228588>] (debug_dma_unmap_page) from [<c02aba64>] (macb_interrupt+0x1f8/0x2dc)
[<c02aba64>] (macb_interrupt) from [<c006c6e4>] (handle_irq_event_percpu+0x2c/0x178)
[<c006c6e4>] (handle_irq_event_percpu) from [<c006c86c>] (handle_irq_event+0x3c/0x5c)
[<c006c86c>] (handle_irq_event) from [<c006f548>] (handle_fasteoi_irq+0xb8/0x100)
[<c006f548>] (handle_fasteoi_irq) from [<c006c148>] (generic_handle_irq+0x20/0x30)
[<c006c148>] (generic_handle_irq) from [<c000f35c>] (handle_IRQ+0x64/0x8c)
[<c000f35c>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
[<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
Exception stack(0xed197f60 to 0xed197fa8)
7f60: 00000134 60000013 bd94362e bd94362e be96b37c 00000014 fffffd72 00000122
7f80: c000ebe4 ed196000 00000000 00000011 c032c0d8 ed197fa8 c0064008 c000ea20
7fa0: 60000013 ffffffff
[<c0012904>] (__irq_svc) from [<c000ea20>] (ret_fast_syscall+0x0/0x48)
---[ end trace 478f921d0d542d1e ]---
Mapped at:
[<c0227184>] debug_dma_map_page+0x48/0x11c
[<c02aaca0>] macb_start_xmit+0x184/0x2a8
[<c03143c0>] dev_hard_start_xmit+0x334/0x470
[<c032c09c>] sch_direct_xmit+0x78/0x2f8
[<c0314814>] __dev_queue_xmit+0x318/0x708
due to missing checks of the dma mapping. Add the appropriate checks to fix
this.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In kexec scenario, we failed to load the mlx4 driver in the
second kernel because the ownership bit was hold by the first
kernel without release correctly.
The patch adds shutdown() interface so that the ownership can
be released correctly in the first kernel. It also helps avoiding
EEH error happened during boot stage of the second kernel because
of undesired traffic, which can't be handled by hardware during
that stage on Power platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a CPDMA RX Descriptor leak that occurs after taking
the interface down when the CPSW is in Dual MAC mode. Previously
the CPSW_ALE port was left open up which causes packets to be received
and processed by the RX interrupt handler and were passed to the
non active network interface where they were ignored.
The fix is for the slave_stop function of the selected interface
to disable the respective CPSW_ALE Port from forwarding packets. This
blocks traffic from being received on the inactive interface.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of TX workarounds in be_xmit_workarounds() routine
are not applicable (and result in HW errors) to Skyhawk-R chip.
Isolate BE3-R/Lancer specific workarounds to a separate routine.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_padto(), skb_share_check() and __vlan_put_tag() routines free
skb when they return an error. This patch fixes be_xmit_workarounds()
to not free skb again in such cases.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mode
We should clear promiscuous bits in adapter->flags while disabling promiscuous
mode. Else we will not put interface back into VLAN promisc mode if the vlans
already added exceeds the maximum limit.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.
Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ->tc_cfg[] array has QLC_DCB_MAX_TC (8) elements so the check is
off by one. These functions are always called with valid values though
so it doesn't affect how the code works.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this patch b44_check_phy() was called when the phy called the
adjust callback. This method only change the mac duplex mode when the
carrier was off. When the phy changed the duplex mode after the carrier
was on the mac was not changed. This happened when an external phy was
used.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When support for external phys was added to b44, the calls to start and
stop the phy were missing in the mac driver. This adds the calls to
phy_start() and phy_stop().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent commit "fe1624c bna: RX Filter Enhancements" disables
VLAN tag stripping if the NIC is in promiscuous mode. This causes
__vlan_hwaccel_put_tag() is called when the stripping is disabled.
Because of this VLAN over bna does not work and causes BUGs in conjunction
with openvswitch like this:
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Redefine the RXD_ERR_MASK to include only relevant error bits. This fixes
a customer reported issue of randomly dropping packets on the 5719.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c14db2025 "bnx2x: Correct default Tx switching behaviour" supposedly
changed the default Tx switching behaviour, but was missing the fastpath change
required for FW to pass packets from PFs to VFs.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we receive a PTP event from the NIC when we haven't set up PTP state
in the driver, we attempt to read through a NULL pointer efx->ptp_data,
triggering a panic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without a shutdown handler, T4 cards behave very badly after a kexec.
Some firmware calls return errors indicating allocation failures, for
example. This is probably because thouse resources were not released by
a BYE message to the firmware, for example.
Using the remove handler guarantees we will use a well tested path.
With this patch I applied, I managed to use kexec multiple times and
probe and iSCSI login worked every time.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Driver was not re-setting sds ring count to 1 after failing
to allocate msi-x interrupts.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o This patch reverts commit 1414abea048e0835c43600d62808ed8163897227
(qlcnic: Restrict VF from configuring any VLAN mode.)
This will allow same multicast address to be used with any VLAN
instead of programming seperate (MAC, VLAN) tuples in adapter.
This will help save some multicast filters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once interrupts are enabled, instead of using module parameters,
use flags (QLCNIC_MSI_ENABLED and QLCNIC_MSIX_ENABLED) set by driver
to check interrupt mode.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
