aboutsummaryrefslogtreecommitdiff
path: root/drivers/ata
AgeCommit message (Collapse)Author
2015-01-29sata_dwc_460ex: fix resource leak on error pathAndy Shevchenko
commit 4aaa71873ddb9faf4b0c4826579e2f6d18ff9ab4 upstream. DMA mapped IO should be unmapped on the error path in probe() and unconditionally on remove(). Fixes: 62936009f35a ([libata] Add 460EX on-chip SATA driver, sata_dwc_460ex) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-29libata: prevent HSM state change race between ISR and PIODavid Jeffery
commit ce7514526742c0898b837d4395f515b79dfb5a12 upstream. It is possible for ata_sff_flush_pio_task() to set ap->hsm_task_state to HSM_ST_IDLE in between the time __ata_sff_port_intr() checks for HSM_ST_IDLE and before it calls ata_sff_hsm_move() causing ata_sff_hsm_move() to BUG(). This problem is hard to reproduce making this patch hard to verify, but this fix will prevent the race. I have not been able to reproduce the problem, but here is a crash dump from a 2.6.32 kernel. On examining the ata port's state, its hsm_task_state field has a value of HSM_ST_IDLE: crash> struct ata_port.hsm_task_state ffff881c1121c000 hsm_task_state = 0 Normally, this should not be possible as ata_sff_hsm_move() was called from ata_sff_host_intr(), which checks hsm_task_state and won't call ata_sff_hsm_move() if it has a HSM_ST_IDLE value. PID: 11053 TASK: ffff8816e846cae0 CPU: 0 COMMAND: "sshd" #0 [ffff88008ba03960] machine_kexec at ffffffff81038f3b #1 [ffff88008ba039c0] crash_kexec at ffffffff810c5d92 #2 [ffff88008ba03a90] oops_end at ffffffff8152b510 #3 [ffff88008ba03ac0] die at ffffffff81010e0b #4 [ffff88008ba03af0] do_trap at ffffffff8152ad74 #5 [ffff88008ba03b50] do_invalid_op at ffffffff8100cf95 #6 [ffff88008ba03bf0] invalid_op at ffffffff8100bf9b [exception RIP: ata_sff_hsm_move+317] RIP: ffffffff813a77ad RSP: ffff88008ba03ca0 RFLAGS: 00010097 RAX: 0000000000000000 RBX: ffff881c1121dc60 RCX: 0000000000000000 RDX: ffff881c1121dd10 RSI: ffff881c1121dc60 RDI: ffff881c1121c000 RBP: ffff88008ba03d00 R8: 0000000000000000 R9: 000000000000002e R10: 000000000001003f R11: 000000000000009b R12: ffff881c1121c000 R13: 0000000000000000 R14: 0000000000000050 R15: ffff881c1121dd78 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #7 [ffff88008ba03d08] ata_sff_host_intr at ffffffff813a7fbd #8 [ffff88008ba03d38] ata_sff_interrupt at ffffffff813a821e #9 [ffff88008ba03d78] handle_IRQ_event at ffffffff810e6ec0
2014-12-16sata_fsl: fix error handling of irq_of_parse_and_mapDmitry Torokhov
commit aad0b624129709c94c2e19e583b6053520353fa8 upstream. irq_of_parse_and_map() returns 0 on error (the result is unsigned int), so testing for negative result never works. Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16ahci: disable MSI on SAMSUNG 0xa800 SSDTejun Heo
commit 2b21ef0aae65f22f5ba86b13c4588f6f0c2dbefb upstream. Just like 0x1600 which got blacklisted by 66a7cbc303f4 ("ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes on NCQ commands if MSI is enabled. Disable MSI. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Dominik Mierzejewski <dominik@greysector.net> Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16AHCI: Add DeviceIDs for Sunrise Point-LP SATA controllerDevin Ryles
commit 249cd0a187ed4ef1d0af7f74362cc2791ec5581b upstream. This patch adds DeviceIDs for Sunrise Point-LP. Signed-off-by: Devin Ryles <devin.ryles@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-21ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooksTejun Heo
commit 66a7cbc303f4d28f201529b06061944d51ab530c upstream. Samsung pci-e SSDs on macbooks failed miserably on NCQ commands, so 67809f85d31e ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks") disabled NCQ on them. It turns out that NCQ is fine as long as MSI is not used, so let's turn off MSI and leave NCQ on. Signed-off-by: Tejun Heo <tj@kernel.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=60731 Tested-by: <dorin@i51.org> Tested-by: Imre Kaloz <kaloz@openwrt.org> Fixes: 67809f85d31e ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-21ahci: Add Device IDs for Intel Sunrise Point PCHJames Ralston
commit 690000b930456a98663567d35dd5c54b688d1e3f upstream. This patch adds the AHCI-mode SATA Device IDs for the Intel Sunrise Point PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-14libata-sff: Fix controllers with no ctl portOndrej Zary
commit 6d8ca28fa688a9354bc9fbc935bdaeb3651b6677 upstream. Currently, ata_sff_softreset is skipped for controllers with no ctl port. But that also skips ata_sff_dev_classify required for device detection. This means that libata is currently broken on controllers with no ctl port. No device connected: [ 1.872480] pata_isapnp 01:01.02: activated [ 1.889823] scsi2 : pata_isapnp [ 1.890109] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 6.888110] ata3.01: qc timeout (cmd 0xec) [ 6.888179] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 16.888085] ata3.01: qc timeout (cmd 0xec) [ 16.888147] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.888086] ata3.01: qc timeout (cmd 0xec) [ 46.888148] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 51.888100] ata3.00: qc timeout (cmd 0xec) [ 51.888160] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) [ 61.888079] ata3.00: qc timeout (cmd 0xec) [ 61.888141] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) [ 91.888089] ata3.00: qc timeout (cmd 0xec) [ 91.888152] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) ATAPI device connected: [ 1.882061] pata_isapnp 01:01.02: activated [ 1.893430] scsi2 : pata_isapnp [ 1.893719] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 6.892107] ata3.01: qc timeout (cmd 0xec) [ 6.892171] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 16.892079] ata3.01: qc timeout (cmd 0xec) [ 16.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.892079] ata3.01: qc timeout (cmd 0xec) [ 46.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.908586] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr [ 46.924570] ata3.00: configured for PIO0 (device error ignored) [ 46.926295] scsi 2:0:0:0: CD-ROM ACER CD-767E/O 1.5X PQ: 0 ANSI: 5 [ 46.984519] sr0: scsi3-mmc drive: 6x/6x xa/form2 tray [ 46.984592] cdrom: Uniform CD-ROM driver Revision: 3.20 So don't skip ata_sff_softreset, just skip the reset part of ata_bus_softreset if the ctl port is not available. This makes IDE port on ES968 behave correctly: No device connected: [ 4.670888] pata_isapnp 01:01.02: activated [ 4.673207] scsi host2: pata_isapnp [ 4.673675] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 7.081840] Adding 2541652k swap on /dev/sda2. Priority:-1 extents:1 across:2541652k ATAPI device connected: [ 4.704362] pata_isapnp 01:01.02: activated [ 4.706620] scsi host2: pata_isapnp [ 4.706877] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 4.872782] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr [ 4.888673] ata3.00: configured for PIO0 (device error ignored) [ 4.893984] scsi 2:0:0:0: CD-ROM ACER CD-767E/O 1.5X PQ: 0 ANSI: 5 [ 7.015578] Adding 2541652k swap on /dev/sda2. Priority:-1 extents:1 across:2541652k Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-14pata_serverworks: disable 64-KB DMA transfers on Broadcom OSB4 IDE ControllerScott Carter
commit 37017ac6849e772e67dd187ba2fbd056c4afa533 upstream. The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211) does not support 64-KB DMA transfers. Whenever a 64-KB DMA transfer is attempted, the transfer fails and messages similar to the following are written to the console log: [ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code [ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current] [ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out [ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00 [ 2431.851210] end_request: I/O error, dev sr0, sector 121808 When the libata and pata_serverworks modules are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h, the 64-KB transfer size in the scatter-gather list can be seen in the console log: [ 2664.897267] sr 9:0:0:0: [sr0] Send: [ 2664.897274] 0xf63d85e0 [ 2664.897283] sr 9:0:0:0: [sr0] CDB: [ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00 [ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700 [ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40 [ 2664.897338] ata_scsi_translate: ENTER [ 2664.897345] ata_sg_setup: ENTER, ata1 [ 2664.897356] ata_sg_setup: 3 sg elements mapped [ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000) [ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000) ------------------------------------------------------> ======= [ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000) [ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1 [ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC [ 2664.897428] ata_sff_tf_load: device 0xA0 [ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0 [ 2664.897457] ata_scsi_translate: EXIT [ 2664.897462] leaving scsi_dispatch_cmnd() [ 2664.897497] Doing sr request, dev = sr0, block = 0 [ 2664.897507] sr0 : reading 64/256 512 byte blocks. [ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58) [ 2664.897560] atapi_send_cdb: send cdb [ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64 [ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3 [ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51) [ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51) [ 2666.910129] sr 9:0:0:0: [sr0] Done: [ 2666.910136] 0xf63d85e0 TIMEOUT lspci shows that the driver used for the Broadcom OSB4 IDE Controller is pata_serverworks: 00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP]) Flags: bus master, medium devsel, latency 64 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=4] I/O ports at 1440 [size=16] Kernel driver in use: pata_serverworks The pata_serverworks driver supports five distinct device IDs, one being the OSB4 and the other four belonging to the CSB series. The CSB series appears to support 64-KB DMA transfers, as tests on a machine with an SAI2 motherboard containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212) showed no problems with 64-KB DMA transfers. This problem was first discovered when attempting to install openSUSE from a DVD on a machine with an STL2 motherboard. Using the pata_serverworks module, older releases of openSUSE will not install at all due to the timeouts. Releases of openSUSE prior to 11.3 can be installed by disabling the pata_serverworks module using the brokenmodules boot parameter, which causes the serverworks module to be used instead. Recent releases of openSUSE (12.2 and later) include better error recovery and will install, though very slowly. On all openSUSE releases, the problem can be recreated on a machine containing a Broadcom OSB4 IDE Controller by mounting an install DVD and running a command similar to the following: find /mnt -type f -print | xargs cat > /dev/null The patch below corrects the problem. Similar to the other ATA drivers that do not support 64-KB DMA transfers, the patch changes the ata_port_operations qc_prep vector to point to a routine that breaks any 64-KB segment into two 32-KB segments and changes the scsi_host_template sg_tablesize element to reduce by half the number of scatter/gather elements allowed. These two changes affect only the OSB4. Signed-off-by: Scott Carter <ccscott@funsoft.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05ata_piix: Add Device IDs for Intel 9 Series PCHJames Ralston
commit 6cad1376954e591c3c41500c4e586e183e7ffe6d upstream. This patch adds the IDE mode SATA Device IDs for the Intel 9 Series PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05ahci: add pcid for Marvel 0x9182 controllerMurali Karicheri
commit c5edfff9db6f4d2c35c802acb4abe0df178becee upstream. Keystone K2E EVM uses Marvel 0x9182 controller. This requires support for the ID in the ahci driver. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05ahci: Add Device IDs for Intel 9 Series PCHJames Ralston
commit 1b071a0947dbce5c184c12262e02540fbc493457 upstream. This patch adds the AHCI mode SATA Device IDs for the Intel 9 Series PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05pata_scc: propagate return value of scc_wait_after_resetArjun Sreedharan
commit 4dc7c76cd500fa78c64adfda4b070b870a2b993c upstream. scc_bus_softreset not necessarily should return zero. Propagate the error code. Signed-off-by: Arjun Sreedharan <arjun024@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-31ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)Romain Degez
commit b32bfc06aefab61acc872dec3222624e6cd867ed upstream. Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by registering the board in the ahci_pci_tbl[]. Note: this HBA also provide a hardware RAID mode when activated in BIOS but specific drivers from the manufacturer are required in this case. Signed-off-by: Romain Degez <romain.degez@gmail.com> Tested-by: Romain Degez <romain.degez@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-31libata: introduce ata_host->n_tags to avoid oops on SAS controllersTejun Heo
commit 1a112d10f03e83fb3a2fdc4c9165865dec8a3ca6 upstream. 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32") directly used ata_port->scsi_host->can_queue from ata_qc_new() to determine the number of tags supported by the host; unfortunately, SAS controllers doing SATA don't initialize ->scsi_host leading to the following oops. BUG: unable to handle kernel NULL pointer dereference at 0000000000000058 IP: [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0 PGD 0 Oops: 0002 [#1] SMP Modules linked in: isci libsas scsi_transport_sas mgag200 drm_kms_helper ttm CPU: 1 PID: 518 Comm: udevd Not tainted 3.16.0-rc6+ #62 Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.02.0002.122320131210 12/23/2013 task: ffff880c1a00b280 ti: ffff88061a000000 task.ti: ffff88061a000000 RIP: 0010:[<ffffffff814e0618>] [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0 RSP: 0018:ffff88061a003ae8 EFLAGS: 00010012 RAX: 0000000000000001 RBX: ffff88000241ca80 RCX: 00000000000000fa RDX: 0000000000000020 RSI: 0000000000000020 RDI: ffff8806194aa298 RBP: ffff88061a003ae8 R08: ffff8806194a8000 R09: 0000000000000000 R10: 0000000000000000 R11: ffff88000241ca80 R12: ffff88061ad58200 R13: ffff8806194aa298 R14: ffffffff814e67a0 R15: ffff8806194a8000 FS: 00007f3ad7fe3840(0000) GS:ffff880627620000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000058 CR3: 000000061a118000 CR4: 00000000001407e0 Stack: ffff88061a003b20 ffffffff814e96e1 ffff88000241ca80 ffff88061ad58200 ffff8800b6bf6000 ffff880c1c988000 ffff880619903850 ffff88061a003b68 ffffffffa0056ce1 ffff88061a003b48 0000000013d6e6f8 ffff88000241ca80 Call Trace: [<ffffffff814e96e1>] ata_sas_queuecmd+0xa1/0x430 [<ffffffffa0056ce1>] sas_queuecommand+0x191/0x220 [libsas] [<ffffffff8149afee>] scsi_dispatch_cmd+0x10e/0x300 [<ffffffff814a3bc5>] scsi_request_fn+0x2f5/0x550 [<ffffffff81317613>] __blk_run_queue+0x33/0x40 [<ffffffff8131781a>] queue_unplugged+0x2a/0x90 [<ffffffff8131ceb4>] blk_flush_plug_list+0x1b4/0x210 [<ffffffff8131d274>] blk_finish_plug+0x14/0x50 [<ffffffff8117eaa8>] __do_page_cache_readahead+0x198/0x1f0 [<ffffffff8117ee21>] force_page_cache_readahead+0x31/0x50 [<ffffffff8117ee7e>] page_cache_sync_readahead+0x3e/0x50 [<ffffffff81172ac6>] generic_file_read_iter+0x496/0x5a0 [<ffffffff81219897>] blkdev_read_iter+0x37/0x40 [<ffffffff811e307e>] new_sync_read+0x7e/0xb0 [<ffffffff811e3734>] vfs_read+0x94/0x170 [<ffffffff811e43c6>] SyS_read+0x46/0xb0 [<ffffffff811e33d1>] ? SyS_lseek+0x91/0xb0 [<ffffffff8171ee29>] system_call_fastpath+0x16/0x1b Code: 00 00 00 88 50 29 83 7f 08 01 19 d2 83 e2 f0 83 ea 50 88 50 34 c6 81 1d 02 00 00 40 c6 81 17 02 00 00 00 5d c3 66 0f 1f 44 00 00 <89> 14 25 58 00 00 00 Fix it by introducing ata_host->n_tags which is initialized to ATA_MAX_QUEUE - 1 in ata_host_init() for SAS controllers and set to scsi_host_template->can_queue in ata_host_register() for !SAS ones. As SAS hosts are never registered, this will give them the same ATA_MAX_QUEUE - 1 as before. Note that we can't use scsi_host->can_queue directly for SAS hosts anyway as they can go higher than the libata maximum. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com> Reported-by: Jesse Brandeburg <jesse.brandeburg@gmail.com> Reported-by: Peter Hurley <peter@hurleysoftware.com> Reported-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru> Fixes: 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32") Cc: Kevin Hao <haokexin@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-31libata: support the ata host which implements a queue depth less than 32Kevin Hao
commit 1871ee134b73fb4cadab75752a7152ed2813c751 upstream. The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2d6 ("libata/ahci: accommodate tag ordered controllers"). The reason is that the ata controller on this SoC only implement a queue depth of 16. When issuing the commands in tag order, all the commands in tag 16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata malfunction. It makes no senses to use a 32 queue in software while the hardware has less queue depth. So consider the queue depth implemented by the hardware when requesting a command tag. Fixes: 8a4aeec8d2d6 ("libata/ahci: accommodate tag ordered controllers") Signed-off-by: Kevin Hao <haokexin@gmail.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-16ahci: add PCI ID for Marvell 88SE91A0 SATA ControllerAndreas Schrägle
commit 754a292fe6b08196cb135c03b404444e17de520a upstream. Add support for Marvell Technology Group Ltd. 88SE91A0 SATA 6Gb/s Controller by adding its PCI ID. Signed-off-by: Andreas Schrägle <ajs124.ajs124@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-16ahci: Add Device ID for HighPoint RocketRaid 642LJérôme Carretero
commit d251836508fb26cd1a22b41381739835ee23728d upstream. This device normally comes with a proprietary driver, using a web GUI to configure RAID: http://www.highpoint-tech.com/USA_new/series_rr600-download.htm But thankfully it also works out of the box with the AHCI driver, being just a Marvell 88SE9235. Devices 640L, 644L, 644LS should also be supported but not tested here. Signed-off-by: Jérôme Carretero <cJ-ko@zougloub.eu> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07libata: clean up ZPODD when a port is detachedLevente Kurusa
commit a6f9bf4d2f965b862b95213303d154e02957eed8 upstream. When a ZPODD device is unbound via sysfs, the ACPI notify handler is not removed. This causes panics as observed in Bug #74601. The panic only happens when the wake happens from outside the kernel (i.e. inserting a media or pressing a button). Add a loop to ata_port_detach which loops through the port's devices and checks if zpodd is enabled, if so call zpodd_exit. Reviewed-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Levente Kurusa <levex@linux.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07pata_at91: fix ata_host_activate() failure handlingBartlomiej Zolnierkiewicz
commit 27aa64b9d1bd0d23fd692c91763a48309b694311 upstream. Add missing clk_put() call to ata_host_activate() failure path. Sergei says, "Hm, I have once fixed that (see that *if* (!ret)) but looks like a later commit 477c87e90853d136b188c50c0e4a93d01cad872e (ARM: at91/pata: use gpio_is_valid to check the gpio) broke it again. :-( Would be good if the changelog did mention that..." Cc: Andrew Victor <linux@maxim.org.za> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-13libata/ahci: accommodate tag ordered controllersDan Williams
commit 8a4aeec8d2d6a3edeffbdfae451cdf05cbf0fefd upstream. The AHCI spec allows implementations to issue commands in tag order rather than FIFO order: 5.3.2.12 P:SelectCmd HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1) or HBA selects the command to issue that has had the PxCI bit set to '1' longer than any other command pending to be issued. The result is that commands posted sequentially (time-wise) may play out of sequence when issued by hardware. This behavior has likely been hidden by drives that arrange for commands to complete in issue order. However, it appears recent drives (two from different vendors that we have found so far) inflict out-of-order completions as a matter of course. So, we need to take care to maintain ordered submission, otherwise we risk triggering a drive to fall out of sequential-io automation and back to random-io processing, which incurs large latency and degrades throughput. This issue was found in simple benchmarks where QD=2 seq-write performance was 30-50% *greater* than QD=32 seq-write performance. Tagging for -stable and making the change globally since it has a low risk-to-reward ratio. Also, word is that recent versions of an unnamed OS also does it this way now. So, drives in the field are already experienced with this tag ordering scheme. Cc: Dave Jiang <dave.jiang@intel.com> Cc: Ed Ciechanowski <ed.ciechanowski@intel.com> Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-23libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint ↵Michele Baldessari
M8 (2BA30001) commit b28a613e9138e4b3a64649bd60b13436f4b4b49b upstream. Via commit 87809942d3fa "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8" we added a quirk for disks named "ST1000LM024 HN-M101MBB" with firmware revision "2AR10001". As reported on https://bugzilla.redhat.com/show_bug.cgi?id=1073901, we need to also add firmware revision 2BA30001 as it is broken as well. Reported-by: Nicholas <arealityfarbetween@googlemail.com> Signed-off-by: Michele Baldessari <michele@acksyn.org> Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-06sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYNTejun Heo
commit 9f9c47f00ce99329b1a82e2ac4f70f0fe3db549c upstream. It's a bit odd to see a newer device showing mod15write; however, the reported behavior is highly consistent and other factors which could contribute seem to have been verified well enough. Also, both sata_sil itself and the drive are fairly outdated at this point making the risk of this change fairly low. It is possible, probably likely, that other drive models in the same family have the same problem; however, for now, let's just add the specific model which was tested. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: matson <lists-matsonpa@luxsci.me> References: http://lkml.kernel.org/g/201401211912.s0LJCk7F015058@rs103.luxsci.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-06ata: enable quirk from jmicron JMB350 for JMB394Denis V. Lunev
commit efb9e0f4f43780f0ae0c6428d66bd03e805c7539 upstream. Without the patch the kernel generates the following error. ata11.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata11.15: Port Multiplier vendor mismatch '0x197b' != '0x123' ata11.15: PMP revalidation failed (errno=-19) ata11.15: failed to recover PMP after 5 tries, giving up This patch helps to bypass this error and the device becomes functional. Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: <linux-ide@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-06ahci: disable NCQ on Samsung pci-e SSDs on macbooksLevente Kurusa
commit 67809f85d31eac600f6b28defa5386c9d2a13b1d upstream. Samsung's pci-e SSDs with device ID 0x1600 which are found on some macbooks time out on NCQ commands. Blacklist NCQ on the device so that the affected machines can at least boot. Original-patch-by: Levente Kurusa <levex@linux.com> Signed-off-by: Tejun Heo <tj@kernel.org> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-06libata: disable LPM for some WD SATA-I devicesTejun Heo
commit ecd75ad514d73efc1bbcc5f10a13566c3ace5f53 upstream. For some reason, some early WD drives spin up and down drives erratically when the link is put into slumber mode which can reduce the life expectancy of the device significantly. Unfortunately, we don't have full list of devices and given the nature of the issue it'd be better to err on the side of false positives than the other way around. Let's disable LPM on all WD devices which match one of the known problematic model prefixes and are SATA-I. As horkage list doesn't support matching SATA capabilities, this is implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is set for the known prefixes and sets the latter if the matched device is SATA-I. Note that this isn't optimal as this disables all LPM operations and partial link power state reportedly works fine on these; however, the way LPM is implemented in libata makes it difficult to precisely map libata LPM setting to specific link power state. Well, these devices are already fairly outdated. Let's just disable whole LPM for now. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com> Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com> References: https://bugzilla.kernel.org/show_bug.cgi?id=57211 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-06ata: sata_mv: fix disk hotplug for Armada 370/XP SoCsLior Amsalem
commit 9013d64e661fc2a37a1742670202171c27fef4b5 upstream. On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the re-plug events are not detected by the sata_mv driver. This patch fixes the issue by updating the PHY speed in the LP_PHY_CTL register (0x58) according to the SControl speed. Note that this fix is only applied if the compatible string "marvell,armada-370-sata" is found in the SATA DT node. Fixes: 9ae6f740b49f ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT") Signed-off-by: Lior Amsalem <alior@marvell.com> Signed-off-by: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-06ata: sata_mv: introduce compatible string "marvell, armada-370-sata"Simon Guinot
commit b1f5c73bd5a4752efb7d7af019034044b08aafe9 upstream. The sata_mv driver supports the SATA IP found in several Marvell SoCs. As some new SATA registers have been introduced with the Armada 370/XP SoCs, a way to identify them is needed. This patch introduces a new compatible string for the SATA IP found in Armada 370/XP SoCs. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Lior Amsalem <alior@marvell.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-15ahci: add PCI ID for Marvell 88SE9170 SATA controllerSimon Guinot
commit e098f5cbe9d410e7878b50f524dce36cc83ec40e upstream. This patch adds support for the PCI ID provided by the Marvell 88SE9170 SATA controller. Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-09libata, freezer: avoid block device removal while system is frozenTejun Heo
commit 85fbd722ad0f5d64d1ad15888cd1eb2188bfb557 upstream. Freezable kthreads and workqueues are fundamentally problematic in that they effectively introduce a big kernel lock widely used in the kernel and have already been the culprit of several deadlock scenarios. This is the latest occurrence. During resume, libata rescans all the ports and revalidates all pre-existing devices. If it determines that a device has gone missing, the device is removed from the system which involves invalidating block device and flushing bdi while holding driver core layer locks. Unfortunately, this can race with the rest of device resume. Because freezable kthreads and workqueues are thawed after device resume is complete and block device removal depends on freezable workqueues and kthreads (e.g. bdi_wq, jbd2) to make progress, this can lead to deadlock - block device removal can't proceed because kthreads are frozen and kthreads can't be thawed because device resume is blocked behind block device removal. 839a8e8660b6 ("writeback: replace custom worker pool implementation with unbound workqueue") made this particular deadlock scenario more visible but the underlying problem has always been there - the original forker task and jbd2 are freezable too. In fact, this is highly likely just one of many possible deadlock scenarios given that freezer behaves as a big kernel lock and we don't have any debug mechanism around it. I believe the right thing to do is getting rid of freezable kthreads and workqueues. This is something fundamentally broken. For now, implement a funny workaround in libata - just avoid doing block device hot[un]plug while the system is frozen. Kernel engineering at its finest. :( v2: Add EXPORT_SYMBOL_GPL(pm_freezing) for cases where libata is built as a module. v3: Comment updated and polling interval changed to 10ms as suggested by Rafael. v4: Add #ifdef CONFIG_FREEZER around the hack as pm_freezing is not defined when FREEZER is not configured thus breaking build. Reported by kbuild test robot. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Tomaž Šolc <tomaz.solc@tablix.org> Reviewed-by: "Rafael J. Wysocki" <rjw@rjwysocki.net> Link: https://bugzilla.kernel.org/show_bug.cgi?id=62801 Link: http://lkml.kernel.org/r/20131213174932.GA27070@htj.dyndns.org Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Len Brown <len.brown@intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-09libata: disable a disk via libata.force paramsRobin H. Johnson
commit b8bd6dc36186fe99afa7b73e9e2d9a98ad5c4865 upstream. A user on StackExchange had a failing SSD that's soldered directly onto the motherboard of his system. The BIOS does not give any option to disable it at all, so he can't just hide it from the OS via the BIOS. The old IDE layer had hdX=noprobe override for situations like this, but that was never ported to the libata layer. This patch implements a disable flag for libata.force. Example use: libata.force=2.0:disable [v2 of the patch, removed the nodisable flag per Tejun Heo] Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Tejun Heo <tj@kernel.org> Link: http://unix.stackexchange.com/questions/102648/how-to-tell-linux-kernel-3-0-to-completely-ignore-a-failing-disk Link: http://askubuntu.com/questions/352836/how-can-i-tell-linux-kernel-to-completely-ignore-a-disk-as-if-it-was-not-even-co Link: http://superuser.com/questions/599333/how-to-disable-kernel-probing-for-drive Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-09libata: Add atapi_dmadir force flagVincent Pelletier
commit 966fbe193f47c68e70a80ec9991098e88e7959cb upstream. Some device require DMADIR to be enabled, but are not detected as such by atapi_id_dmadir. One such example is "Asus Serillel 2" SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR, even if the bridged device does not. As atapi_dmadir module parameter can cause problems with some devices (as per Tejun Heo's memory), enabling it globally may not be possible depending on the hardware. This patch adds atapi_dmadir in the form of a "force" horkage value, allowing global, per-bus and per-device control. Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-09libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8Michele Baldessari
commit 87809942d3fa60bafb7a58d0bdb1c79e90a6821d upstream. We've received multiple reports in Fedora via (BZ 907193) that the Seagate Momentus SpinPoint M8 errors out when enabling AA: [ 2.555905] ata2.00: failed to enable AA (error_mask=0x1) [ 2.568482] ata2.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. Reported-by: Nicholas <arealityfarbetween@googlemail.com> Signed-off-by: Michele Baldessari <michele@acksyn.org> Tested-by: Nicholas <arealityfarbetween@googlemail.com> Acked-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-11SCSI: Disable WRITE SAME for RAID and virtual host adapter driversMartin K. Petersen
commit 54b2b50c20a61b51199bedb6e5d2f8ec2568fb43 upstream. Some host adapters do not pass commands through to the target disk directly. Instead they provide an emulated target which may or may not accurately report its capabilities. In some cases the physical device characteristics are reported even when the host adapter is processing commands on the device's behalf. This can lead to adapter firmware hangs or excessive I/O errors. This patch disables WRITE SAME for devices connected to host adapters that provide an emulated target. Driver writers can disable WRITE SAME by setting the no_write_same flag in the host adapter template. [jejb: fix up rejections due to eh_deadline patch] Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04ahci: add Marvell 9230 to the AHCI PCI device listSamir Benmendil
commit 6d5278a68a75891db1df5ae1ecf83d288fc58c65 upstream. Tested with a DAWICONTROL DC-624e on 3.10.10 Signed-off-by: Samir Benmendil <samir.benmendil@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Levente Kurusa <levex@linux.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04ahci: disabled FBS prior to issuing software resetxiangliang yu
commit 89dafa20f3daab5b3e0c13d0068a28e8e64e2102 upstream. Tested with Marvell 88se9125, attached with one port mulitplier(5 ports) and one disk, we will get following boot log messages if using current code: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f ahci 0000:03:00.0: FBS is enabled ata8.00: hard resetting link ata8.00: SATA link down (SStatus 0 SControl 330) ata8.01: hard resetting link ata8.01: SATA link down (SStatus 0 SControl 330) ata8.02: hard resetting link ata8.02: SATA link down (SStatus 0 SControl 330) ata8.03: hard resetting link ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133) ata8.04: hard resetting link ata8.04: failed to resume link (SControl 133) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.04: failed to read SCR 1 (Emask=0x40) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.03: native sectors (2) is smaller than sectors (976773168) ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133 ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata8.03: configured for UDMA/133 ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100) ata8.15: hard resetting link ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: hard resetting link ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: limiting SATA link speed to 3.0 Gbps ata8.15: hard resetting link ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: failed to recover PMP after 5 tries, giving up ata8.15: Port Multiplier detaching ata8.03: disabled ata8.00: disabled ata8: EH complete The reason is that current detection code doesn't follow AHCI spec: First,the port multiplier detection process look like this: ahci_hardreset(link, class, deadline) if (class == ATA_DEV_PMP) { sata_pmp_attach(dev) /* will enable FBS */ sata_pmp_init_links(ap, nr_ports); ata_for_each_link(link, ap, EDGE) { sata_std_hardreset(link, class, deadline); if (link_is_online) /* do soft reset */ ahci_softreset(link, class, deadline); } } But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to '0'. The patch test ok with kernel 3.11.1. tj: Patch white space contaminated, applied manually with trivial updates. Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04ahci: Add Device IDs for Intel Wildcat Point-LPJames Ralston
commit 9f961a5f6efc87a79571d7166257b36af28ffcfe upstream. This patch adds the AHCI-mode SATA Device IDs for the Intel Wildcat Point-LP PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH driveShan Hai
commit 0523f037f65dba10191b0fa9c51266f90ba64630 upstream. The "Slimtype DVD A DS8A9SH" drive locks up with following backtrace when the max sector is smaller than 65535 bytes, fix it by adding a quirk to set the max sector to 65535 bytes. INFO: task flush-11:0:663 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. flush-11:0 D 00000000ffff5ceb 0 663 2 0x00000000 ffff88026d3b1710 0000000000000046 0000000000000001 0000000000000000 ffff88026f2530c0 ffff88026d365860 ffff88026d3b16e0 ffffffff812ffd52 ffff88026d4fd3d0 0000000100000001 ffff88026d3b16f0 ffff88026d3b1fd8 Call Trace: [<ffffffff812ffd52>] ? cfq_may_queue+0x52/0xf0 [<ffffffff81604338>] schedule+0x18/0x30 [<ffffffff81604392>] io_schedule+0x42/0x60 [<ffffffff812f22bb>] get_request_wait+0xeb/0x1f0 [<ffffffff81065660>] ? autoremove_wake_function+0x0/0x40 [<ffffffff812eb382>] ? elv_merge+0x42/0x210 [<ffffffff812f26ae>] __make_request+0x8e/0x4e0 [<ffffffff812f068e>] generic_make_request+0x21e/0x5e0 [<ffffffff812f0aad>] submit_bio+0x5d/0xd0 [<ffffffff81141422>] submit_bh+0xf2/0x130 [<ffffffff8114474c>] __block_write_full_page+0x1dc/0x3a0 [<ffffffff81143f60>] ? end_buffer_async_write+0x0/0x120 [<ffffffff811474e0>] ? blkdev_get_block+0x0/0x70 [<ffffffff811474e0>] ? blkdev_get_block+0x0/0x70 [<ffffffff81143f60>] ? end_buffer_async_write+0x0/0x120 [<ffffffff811449ee>] block_write_full_page_endio+0xde/0x100 [<ffffffff81144a20>] block_write_full_page+0x10/0x20 [<ffffffff81148703>] blkdev_writepage+0x13/0x20 [<ffffffff810d7525>] __writepage+0x15/0x40 [<ffffffff810d7c0f>] write_cache_pages+0x1cf/0x3e0 [<ffffffff810d7510>] ? __writepage+0x0/0x40 [<ffffffff810d7e42>] generic_writepages+0x22/0x30 [<ffffffff810d7e6f>] do_writepages+0x1f/0x40 [<ffffffff8113ae67>] writeback_single_inode+0xe7/0x3b0 [<ffffffff8113b574>] writeback_sb_inodes+0x184/0x280 [<ffffffff8113bedb>] writeback_inodes_wb+0x6b/0x1a0 [<ffffffff8113c24b>] wb_writeback+0x23b/0x2a0 [<ffffffff8113c42d>] wb_do_writeback+0x17d/0x190 [<ffffffff8113c48b>] bdi_writeback_task+0x4b/0xe0 [<ffffffff810e82a0>] ? bdi_start_fn+0x0/0x100 [<ffffffff810e8321>] bdi_start_fn+0x81/0x100 [<ffffffff810e82a0>] ? bdi_start_fn+0x0/0x100 [<ffffffff8106522e>] kthread+0x8e/0xa0 [<ffffffff81039274>] ? finish_task_switch+0x54/0xc0 [<ffffffff81003334>] kernel_thread_helper+0x4/0x10 [<ffffffff810651a0>] ? kthread+0x0/0xa0 [<ffffffff81003330>] ? kernel_thread_helper+0x0/0x10 The above trace was triggered by "dd if=/dev/zero of=/dev/sr0 bs=2048 count=32768" Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04libata: Fix display of sata speedGwendal Grignou
commit 3e85c3ecbc520751324a191d23bb94873ed01b10 upstream. 6.0 Gbps link speed was not decoded properly: speed was reported at 3.0 Gbps only. Tested: On a machine where libata reports 6.0 Gbps in /var/log/messages: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Before: cat /sys/class/ata_link/link1/sata_spd 3.0 Gbps After: cat /sys/class/ata_link/link1/sata_spd 6.0 Gbps Signed-off-by: Gwendal Grignou <gwendal@google.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-11-13libata: make ata_eh_qc_retry() bump scmd->allowed on bogus failuresGwendal Grignou
commit f13e220161e738c2710b9904dcb3cf8bb0bcce61 upstream. libata EH decrements scmd->retries when the command failed for reasons unrelated to the command itself so that, for example, commands aborted due to suspend / resume cycle don't get penalized; however, decrementing scmd->retries isn't enough for ATA passthrough commands. Without this fix, ATA passthrough commands are not resend to the drive, and no error is signalled to the caller because: - allowed retry count is 1 - ata_eh_qc_complete fill the sense data, so result is valid - sense data is filled with untouched ATA registers. Signed-off-by: Gwendal Grignou <gwendal@google.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-29libata: apply behavioral quirks to sil3826 PMPTerry Suereth
commit 8ffff94d20b7eb446e848e0046107d51b17a20a8 upstream. Fixing support for the Silicon Image 3826 port multiplier, by applying to it the same quirks applied to the Silicon Image 3726. Specifically fixes the repeated timeout/reset process which previously afflicted the 3726, as described from line 290. Slightly based on notes from: https://bugzilla.redhat.com/show_bug.cgi?id=890237 Signed-off-by: Terry Suereth <terry.suereth@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-29sata_fsl: save irqs while coalescingAnthony Foiani
commit 99bbdfa6bdcb4bdf5be914a48e9b46941bf30819 upstream. Before this patch, I was seeing the following lockdep splat on my MPC8315 (PPC32) target: [ 9.086051] ================================= [ 9.090393] [ INFO: inconsistent lock state ] [ 9.094744] 3.9.7-ajf-gc39503d #1 Not tainted [ 9.099087] --------------------------------- [ 9.103432] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage. [ 9.109431] scsi_eh_1/39 [HC1[1]:SC0[0]:HE0:SE1] takes: [ 9.114642] (&(&host->lock)->rlock){?.+...}, at: [<c02f4168>] sata_fsl_interrupt+0x50/0x250 [ 9.123137] {HARDIRQ-ON-W} state was registered at: [ 9.128004] [<c006cdb8>] lock_acquire+0x90/0xf4 [ 9.132737] [<c043ef04>] _raw_spin_lock+0x34/0x4c [ 9.137645] [<c02f3560>] fsl_sata_set_irq_coalescing+0x68/0x100 [ 9.143750] [<c02f36a0>] sata_fsl_init_controller+0xa8/0xc0 [ 9.149505] [<c02f3f10>] sata_fsl_probe+0x17c/0x2e8 [ 9.154568] [<c02acc90>] driver_probe_device+0x90/0x248 [ 9.159987] [<c02acf0c>] __driver_attach+0xc4/0xc8 [ 9.164964] [<c02aae74>] bus_for_each_dev+0x5c/0xa8 [ 9.170028] [<c02ac218>] bus_add_driver+0x100/0x26c [ 9.175091] [<c02ad638>] driver_register+0x88/0x198 [ 9.180155] [<c0003a24>] do_one_initcall+0x58/0x1b4 [ 9.185226] [<c05aeeac>] kernel_init_freeable+0x118/0x1c0 [ 9.190823] [<c0004110>] kernel_init+0x18/0x108 [ 9.195542] [<c000f6b8>] ret_from_kernel_thread+0x64/0x6c [ 9.201142] irq event stamp: 160 [ 9.204366] hardirqs last enabled at (159): [<c043f778>] _raw_spin_unlock_irq+0x30/0x50 [ 9.212469] hardirqs last disabled at (160): [<c000f414>] reenable_mmu+0x30/0x88 [ 9.219867] softirqs last enabled at (144): [<c002ae5c>] __do_softirq+0x168/0x218 [ 9.227435] softirqs last disabled at (137): [<c002b0d4>] irq_exit+0xa8/0xb4 [ 9.234481] [ 9.234481] other info that might help us debug this: [ 9.240995] Possible unsafe locking scenario: [ 9.240995] [ 9.246898] CPU0 [ 9.249337] ---- [ 9.251776] lock(&(&host->lock)->rlock); [ 9.255878] <Interrupt> [ 9.258492] lock(&(&host->lock)->rlock); [ 9.262765] [ 9.262765] *** DEADLOCK *** [ 9.262765] [ 9.268684] no locks held by scsi_eh_1/39. [ 9.272767] [ 9.272767] stack backtrace: [ 9.277117] Call Trace: [ 9.279589] [cfff9da0] [c0008504] show_stack+0x48/0x150 (unreliable) [ 9.285972] [cfff9de0] [c0447d5c] print_usage_bug.part.35+0x268/0x27c [ 9.292425] [cfff9e10] [c006ace4] mark_lock+0x2ac/0x658 [ 9.297660] [cfff9e40] [c006b7e4] __lock_acquire+0x754/0x1840 [ 9.303414] [cfff9ee0] [c006cdb8] lock_acquire+0x90/0xf4 [ 9.308745] [cfff9f20] [c043ef04] _raw_spin_lock+0x34/0x4c [ 9.314250] [cfff9f30] [c02f4168] sata_fsl_interrupt+0x50/0x250 [ 9.320187] [cfff9f70] [c0079ff0] handle_irq_event_percpu+0x90/0x254 [ 9.326547] [cfff9fc0] [c007a1fc] handle_irq_event+0x48/0x78 [ 9.332220] [cfff9fe0] [c007c95c] handle_level_irq+0x9c/0x104 [ 9.337981] [cfff9ff0] [c000d978] call_handle_irq+0x18/0x28 [ 9.343568] [cc7139f0] [c000608c] do_IRQ+0xf0/0x1a8 [ 9.348464] [cc713a20] [c000fc8c] ret_from_except+0x0/0x14 [ 9.353983] --- Exception: 501 at _raw_spin_unlock_irq+0x40/0x50 [ 9.353983] LR = _raw_spin_unlock_irq+0x30/0x50 [ 9.364839] [cc713af0] [c043db10] wait_for_common+0xac/0x188 [ 9.370513] [cc713b30] [c02ddee4] ata_exec_internal_sg+0x2b0/0x4f0 [ 9.376699] [cc713be0] [c02de18c] ata_exec_internal+0x68/0xa8 [ 9.382454] [cc713c20] [c02de4b8] ata_dev_read_id+0x158/0x594 [ 9.388205] [cc713ca0] [c02ec244] ata_eh_recover+0xd88/0x13d0 [ 9.393962] [cc713d20] [c02f2520] sata_pmp_error_handler+0xc0/0x8ac [ 9.400234] [cc713dd0] [c02ecdc8] ata_scsi_port_error_handler+0x464/0x5e8 [ 9.407023] [cc713e10] [c02ecfd0] ata_scsi_error+0x84/0xb8 [ 9.412528] [cc713e40] [c02c4974] scsi_error_handler+0xd8/0x47c [ 9.418457] [cc713eb0] [c004737c] kthread+0xa8/0xac [ 9.423355] [cc713f40] [c000f6b8] ret_from_kernel_thread+0x64/0x6c This fix was suggested by Bhushan Bharat <R65777@freescale.com>, and was discussed in email at: http://linuxppc.10917.n7.nabble.com/MPC8315-reboot-failure-lockdep-splat-possibly-related-tp75162.html Same patch successfully tested with 3.9.7. linux-next compiled but not tested on hardware. This patch is based off linux-next tag next-20130819 (which is commit 66a01bae29d11916c09f9f5a937cafe7d402e4a5 ) Signed-off-by: Anthony Foiani <anthony.foiani@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-04libata: make it clear that sata_inic162x is experimentalTejun Heo
commit bb9696192826a7d9279caf872e95b41bc26c7eff upstream. sata_inic162x never reached a state where it's reliable enough for production use and data corruption is a relatively common occurrence. Make the driver generate warning about the issues and mark the Kconfig option as experimental. If the situation doesn't improve, we'd be better off making it depend on CONFIG_BROKEN. Let's wait for several cycles and see if the kernel message draws any attention. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Martin Braure de Calignon <braurede@free.fr> Reported-by: Ben Hutchings <ben@decadent.org.uk> Reported-by: risc4all@yahoo.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-04ata: Fix DVD not dectected at some platform with Wellsburg PCHYouquan Song
commit eac27f04a71e1f39f196f7e520d16dcefc955d77 upstream. There is a patch b55f84e2d527182e7c611d466cd0bb6ddce201de "ata_piix: Fix DVD not dectected at some Haswell platforms" to fix an issue of DVD not recognized on Haswell Desktop platform with Lynx Point. Recently, it is also found the same issue at some platformas with Wellsburg PCH. So deliver a similar patch to fix it by disables 32bit PIO in IDE mode. Signed-off-by: Youquan Song <youquan.song@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-25sata_highbank: increase retry count but shorten duration for Calxeda controllerMark Langsdorf
commit ddfef5de3d716f77bad32dbbba6b280158dfd721 upstream. Increase the retry count for the hard reset function to 100 but shorten the time out period to 500 ms. See the comment for ahci_highbank_hardreset for the reasons why those vaulues were chosen. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-25ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDsSeth Heasley
commit c7e8695bfa0611b39493a9dfe8bab9f63f9809bd upstream. This patch adds the IDE-mode SATA DeviceIDs for the Intel Coleto Creek PCH. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-25libata: skip SRST for all SIMG [34]7x port-multipliersTejun Heo
commit 7a87718d92760fc688628ad6a430643dafa16f1f upstream. For some reason, a lot of port-multipliers have issues with softreset. SIMG [34]7x series port-multipliers have been quite erratic in this regard. I recall that it was better with some firmware revisions and the current list of quirks worked fine for a while. I think it got worse with later firmwares or maybe my test coverage wasn't good enough. Anyways, HPA is reporting that his 3726 setup suffers SRST failures and then the PMP gets confused and fails to probe the last port. The hope was that we try to stick to the standard as much as possible and soonish the PMPs and their firmwares will improve in quality, so the quirk list was kept to minimum. Well, it seems like that's never gonna happen. Let's set NO_SRST for all [34]7x PMPs so that whatever remaining userbase of the device suffer the least. Maybe we should do the same for 57xx's but unfortunately I don't have any device left to test and I'm not even sure 57xx's have ever been made widely available, so let's leave those alone for now. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-25libata-zpodd: must use ata_tf_init()Sergei Shtylyov
commit d0887c43f51c308b01605346e55d906ba858a6f9 upstream. There are some SATA controllers which have both devices 0 and 1 but this module just zeroes out taskfile and sets then ATA_TFLAG_DEVICE (not sure that's needed) which could lead to a wrong device being selected just before issuing command. Thus we should call ata_tf_init() which sets up the device register value properly, like all other users of ata_exec_internal() do... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-21ahci: remove pmp link online check in FBS EHShane Huang
commit 912b9ac683b112615d5605686f1dc086402ce9f7 upstream. ata_link_online() check in ahci_error_intr() is unnecessary, it should be removed otherwise may lead to lockup with FBS enabled PMP. http://marc.info/?l=linux-ide&m=137050421603272&w=2 Reported-by: Yu Liu <liuyu.ac@gmail.com> Signed-off-by: Shane Huang <shane.huang@amd.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-21ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDsSeth Heasley
commit 1cfc7df3de10c40ed459e13cce6de616023bf41c upstream. This patch adds the AHCI-mode SATA DeviceIDs for the Intel Coleto Creek PCH. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>