aboutsummaryrefslogtreecommitdiff
path: root/drivers/ata/libata-core.c
AgeCommit message (Collapse)Author
2014-07-31libata: introduce ata_host->n_tags to avoid oops on SAS controllersTejun Heo
commit 1a112d10f03e83fb3a2fdc4c9165865dec8a3ca6 upstream. 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32") directly used ata_port->scsi_host->can_queue from ata_qc_new() to determine the number of tags supported by the host; unfortunately, SAS controllers doing SATA don't initialize ->scsi_host leading to the following oops. BUG: unable to handle kernel NULL pointer dereference at 0000000000000058 IP: [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0 PGD 0 Oops: 0002 [#1] SMP Modules linked in: isci libsas scsi_transport_sas mgag200 drm_kms_helper ttm CPU: 1 PID: 518 Comm: udevd Not tainted 3.16.0-rc6+ #62 Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.02.0002.122320131210 12/23/2013 task: ffff880c1a00b280 ti: ffff88061a000000 task.ti: ffff88061a000000 RIP: 0010:[<ffffffff814e0618>] [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0 RSP: 0018:ffff88061a003ae8 EFLAGS: 00010012 RAX: 0000000000000001 RBX: ffff88000241ca80 RCX: 00000000000000fa RDX: 0000000000000020 RSI: 0000000000000020 RDI: ffff8806194aa298 RBP: ffff88061a003ae8 R08: ffff8806194a8000 R09: 0000000000000000 R10: 0000000000000000 R11: ffff88000241ca80 R12: ffff88061ad58200 R13: ffff8806194aa298 R14: ffffffff814e67a0 R15: ffff8806194a8000 FS: 00007f3ad7fe3840(0000) GS:ffff880627620000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000058 CR3: 000000061a118000 CR4: 00000000001407e0 Stack: ffff88061a003b20 ffffffff814e96e1 ffff88000241ca80 ffff88061ad58200 ffff8800b6bf6000 ffff880c1c988000 ffff880619903850 ffff88061a003b68 ffffffffa0056ce1 ffff88061a003b48 0000000013d6e6f8 ffff88000241ca80 Call Trace: [<ffffffff814e96e1>] ata_sas_queuecmd+0xa1/0x430 [<ffffffffa0056ce1>] sas_queuecommand+0x191/0x220 [libsas] [<ffffffff8149afee>] scsi_dispatch_cmd+0x10e/0x300 [<ffffffff814a3bc5>] scsi_request_fn+0x2f5/0x550 [<ffffffff81317613>] __blk_run_queue+0x33/0x40 [<ffffffff8131781a>] queue_unplugged+0x2a/0x90 [<ffffffff8131ceb4>] blk_flush_plug_list+0x1b4/0x210 [<ffffffff8131d274>] blk_finish_plug+0x14/0x50 [<ffffffff8117eaa8>] __do_page_cache_readahead+0x198/0x1f0 [<ffffffff8117ee21>] force_page_cache_readahead+0x31/0x50 [<ffffffff8117ee7e>] page_cache_sync_readahead+0x3e/0x50 [<ffffffff81172ac6>] generic_file_read_iter+0x496/0x5a0 [<ffffffff81219897>] blkdev_read_iter+0x37/0x40 [<ffffffff811e307e>] new_sync_read+0x7e/0xb0 [<ffffffff811e3734>] vfs_read+0x94/0x170 [<ffffffff811e43c6>] SyS_read+0x46/0xb0 [<ffffffff811e33d1>] ? SyS_lseek+0x91/0xb0 [<ffffffff8171ee29>] system_call_fastpath+0x16/0x1b Code: 00 00 00 88 50 29 83 7f 08 01 19 d2 83 e2 f0 83 ea 50 88 50 34 c6 81 1d 02 00 00 40 c6 81 17 02 00 00 00 5d c3 66 0f 1f 44 00 00 <89> 14 25 58 00 00 00 Fix it by introducing ata_host->n_tags which is initialized to ATA_MAX_QUEUE - 1 in ata_host_init() for SAS controllers and set to scsi_host_template->can_queue in ata_host_register() for !SAS ones. As SAS hosts are never registered, this will give them the same ATA_MAX_QUEUE - 1 as before. Note that we can't use scsi_host->can_queue directly for SAS hosts anyway as they can go higher than the libata maximum. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com> Reported-by: Jesse Brandeburg <jesse.brandeburg@gmail.com> Reported-by: Peter Hurley <peter@hurleysoftware.com> Reported-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru> Fixes: 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32") Cc: Kevin Hao <haokexin@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-31libata: support the ata host which implements a queue depth less than 32Kevin Hao
commit 1871ee134b73fb4cadab75752a7152ed2813c751 upstream. The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2d6 ("libata/ahci: accommodate tag ordered controllers"). The reason is that the ata controller on this SoC only implement a queue depth of 16. When issuing the commands in tag order, all the commands in tag 16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata malfunction. It makes no senses to use a 32 queue in software while the hardware has less queue depth. So consider the queue depth implemented by the hardware when requesting a command tag. Fixes: 8a4aeec8d2d6 ("libata/ahci: accommodate tag ordered controllers") Signed-off-by: Kevin Hao <haokexin@gmail.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07libata: clean up ZPODD when a port is detachedLevente Kurusa
commit a6f9bf4d2f965b862b95213303d154e02957eed8 upstream. When a ZPODD device is unbound via sysfs, the ACPI notify handler is not removed. This causes panics as observed in Bug #74601. The panic only happens when the wake happens from outside the kernel (i.e. inserting a media or pressing a button). Add a loop to ata_port_detach which loops through the port's devices and checks if zpodd is enabled, if so call zpodd_exit. Reviewed-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Levente Kurusa <levex@linux.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-13libata/ahci: accommodate tag ordered controllersDan Williams
commit 8a4aeec8d2d6a3edeffbdfae451cdf05cbf0fefd upstream. The AHCI spec allows implementations to issue commands in tag order rather than FIFO order: 5.3.2.12 P:SelectCmd HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1) or HBA selects the command to issue that has had the PxCI bit set to '1' longer than any other command pending to be issued. The result is that commands posted sequentially (time-wise) may play out of sequence when issued by hardware. This behavior has likely been hidden by drives that arrange for commands to complete in issue order. However, it appears recent drives (two from different vendors that we have found so far) inflict out-of-order completions as a matter of course. So, we need to take care to maintain ordered submission, otherwise we risk triggering a drive to fall out of sequential-io automation and back to random-io processing, which incurs large latency and degrades throughput. This issue was found in simple benchmarks where QD=2 seq-write performance was 30-50% *greater* than QD=32 seq-write performance. Tagging for -stable and making the change globally since it has a low risk-to-reward ratio. Also, word is that recent versions of an unnamed OS also does it this way now. So, drives in the field are already experienced with this tag ordering scheme. Cc: Dave Jiang <dave.jiang@intel.com> Cc: Ed Ciechanowski <ed.ciechanowski@intel.com> Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-23libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint ↵Michele Baldessari
M8 (2BA30001) commit b28a613e9138e4b3a64649bd60b13436f4b4b49b upstream. Via commit 87809942d3fa "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8" we added a quirk for disks named "ST1000LM024 HN-M101MBB" with firmware revision "2AR10001". As reported on https://bugzilla.redhat.com/show_bug.cgi?id=1073901, we need to also add firmware revision 2BA30001 as it is broken as well. Reported-by: Nicholas <arealityfarbetween@googlemail.com> Signed-off-by: Michele Baldessari <michele@acksyn.org> Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-06libata: disable LPM for some WD SATA-I devicesTejun Heo
commit ecd75ad514d73efc1bbcc5f10a13566c3ace5f53 upstream. For some reason, some early WD drives spin up and down drives erratically when the link is put into slumber mode which can reduce the life expectancy of the device significantly. Unfortunately, we don't have full list of devices and given the nature of the issue it'd be better to err on the side of false positives than the other way around. Let's disable LPM on all WD devices which match one of the known problematic model prefixes and are SATA-I. As horkage list doesn't support matching SATA capabilities, this is implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is set for the known prefixes and sets the latter if the matched device is SATA-I. Note that this isn't optimal as this disables all LPM operations and partial link power state reportedly works fine on these; however, the way LPM is implemented in libata makes it difficult to precisely map libata LPM setting to specific link power state. Well, these devices are already fairly outdated. Let's just disable whole LPM for now. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com> Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com> References: https://bugzilla.kernel.org/show_bug.cgi?id=57211 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-09libata: disable a disk via libata.force paramsRobin H. Johnson
commit b8bd6dc36186fe99afa7b73e9e2d9a98ad5c4865 upstream. A user on StackExchange had a failing SSD that's soldered directly onto the motherboard of his system. The BIOS does not give any option to disable it at all, so he can't just hide it from the OS via the BIOS. The old IDE layer had hdX=noprobe override for situations like this, but that was never ported to the libata layer. This patch implements a disable flag for libata.force. Example use: libata.force=2.0:disable [v2 of the patch, removed the nodisable flag per Tejun Heo] Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Tejun Heo <tj@kernel.org> Link: http://unix.stackexchange.com/questions/102648/how-to-tell-linux-kernel-3-0-to-completely-ignore-a-failing-disk Link: http://askubuntu.com/questions/352836/how-can-i-tell-linux-kernel-to-completely-ignore-a-disk-as-if-it-was-not-even-co Link: http://superuser.com/questions/599333/how-to-disable-kernel-probing-for-drive Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-09libata: Add atapi_dmadir force flagVincent Pelletier
commit 966fbe193f47c68e70a80ec9991098e88e7959cb upstream. Some device require DMADIR to be enabled, but are not detected as such by atapi_id_dmadir. One such example is "Asus Serillel 2" SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR, even if the bridged device does not. As atapi_dmadir module parameter can cause problems with some devices (as per Tejun Heo's memory), enabling it globally may not be possible depending on the hardware. This patch adds atapi_dmadir in the form of a "force" horkage value, allowing global, per-bus and per-device control. Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-09libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8Michele Baldessari
commit 87809942d3fa60bafb7a58d0bdb1c79e90a6821d upstream. We've received multiple reports in Fedora via (BZ 907193) that the Seagate Momentus SpinPoint M8 errors out when enabling AA: [ 2.555905] ata2.00: failed to enable AA (error_mask=0x1) [ 2.568482] ata2.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. Reported-by: Nicholas <arealityfarbetween@googlemail.com> Signed-off-by: Michele Baldessari <michele@acksyn.org> Tested-by: Nicholas <arealityfarbetween@googlemail.com> Acked-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH driveShan Hai
commit 0523f037f65dba10191b0fa9c51266f90ba64630 upstream. The "Slimtype DVD A DS8A9SH" drive locks up with following backtrace when the max sector is smaller than 65535 bytes, fix it by adding a quirk to set the max sector to 65535 bytes. INFO: task flush-11:0:663 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. flush-11:0 D 00000000ffff5ceb 0 663 2 0x00000000 ffff88026d3b1710 0000000000000046 0000000000000001 0000000000000000 ffff88026f2530c0 ffff88026d365860 ffff88026d3b16e0 ffffffff812ffd52 ffff88026d4fd3d0 0000000100000001 ffff88026d3b16f0 ffff88026d3b1fd8 Call Trace: [<ffffffff812ffd52>] ? cfq_may_queue+0x52/0xf0 [<ffffffff81604338>] schedule+0x18/0x30 [<ffffffff81604392>] io_schedule+0x42/0x60 [<ffffffff812f22bb>] get_request_wait+0xeb/0x1f0 [<ffffffff81065660>] ? autoremove_wake_function+0x0/0x40 [<ffffffff812eb382>] ? elv_merge+0x42/0x210 [<ffffffff812f26ae>] __make_request+0x8e/0x4e0 [<ffffffff812f068e>] generic_make_request+0x21e/0x5e0 [<ffffffff812f0aad>] submit_bio+0x5d/0xd0 [<ffffffff81141422>] submit_bh+0xf2/0x130 [<ffffffff8114474c>] __block_write_full_page+0x1dc/0x3a0 [<ffffffff81143f60>] ? end_buffer_async_write+0x0/0x120 [<ffffffff811474e0>] ? blkdev_get_block+0x0/0x70 [<ffffffff811474e0>] ? blkdev_get_block+0x0/0x70 [<ffffffff81143f60>] ? end_buffer_async_write+0x0/0x120 [<ffffffff811449ee>] block_write_full_page_endio+0xde/0x100 [<ffffffff81144a20>] block_write_full_page+0x10/0x20 [<ffffffff81148703>] blkdev_writepage+0x13/0x20 [<ffffffff810d7525>] __writepage+0x15/0x40 [<ffffffff810d7c0f>] write_cache_pages+0x1cf/0x3e0 [<ffffffff810d7510>] ? __writepage+0x0/0x40 [<ffffffff810d7e42>] generic_writepages+0x22/0x30 [<ffffffff810d7e6f>] do_writepages+0x1f/0x40 [<ffffffff8113ae67>] writeback_single_inode+0xe7/0x3b0 [<ffffffff8113b574>] writeback_sb_inodes+0x184/0x280 [<ffffffff8113bedb>] writeback_inodes_wb+0x6b/0x1a0 [<ffffffff8113c24b>] wb_writeback+0x23b/0x2a0 [<ffffffff8113c42d>] wb_do_writeback+0x17d/0x190 [<ffffffff8113c48b>] bdi_writeback_task+0x4b/0xe0 [<ffffffff810e82a0>] ? bdi_start_fn+0x0/0x100 [<ffffffff810e8321>] bdi_start_fn+0x81/0x100 [<ffffffff810e82a0>] ? bdi_start_fn+0x0/0x100 [<ffffffff8106522e>] kthread+0x8e/0xa0 [<ffffffff81039274>] ? finish_task_switch+0x54/0xc0 [<ffffffff81003334>] kernel_thread_helper+0x4/0x10 [<ffffffff810651a0>] ? kthread+0x0/0xa0 [<ffffffff81003330>] ? kernel_thread_helper+0x0/0x10 The above trace was triggered by "dd if=/dev/zero of=/dev/sr0 bs=2048 count=32768" Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-25libata-acpi: add back ACPI based hotplug functionalityAaron Lu
Commit 30dcf76acc69 "libata: migrate ACPI code over to new bindings" mistakenly dropped the code to register hotplug notificaion handler for ATA port/devices, causing regression for people using ATA bay, as kernel bug #59871 shows. Fix this by adding back the hotplug notification handler registration code. Since this code has to be run once and notification needs to be installed on every ATA port/devices handle no matter if there is actual device attached, we can't do this in binding time for ATA device ACPI handle, as the binding only occurs when a SCSI device is created, i.e. there is device attached. So introduce the ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles and if it is available, install the notificaion handler for it during ATA init time. With the ATA ACPI handle binding to SCSI device tree, it is possible now that when the SCSI hotplug work removes the SCSI device, the ACPI unbind function will find that the corresponding ACPI device has already been deleted by dock driver, causing a scaring message like: [ 128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt Fix this by waiting for SCSI hotplug task finish in our notificaion handler, so that the removal of ACPI device done in ACPI unbind function triggered by the removal of SCSI device is run earlier when ACPI device is still available. [rjw: Rebased] References: https://bugzilla.kernel.org/show_bug.cgi?id=59871 Reported-bisected-and-tested-by: Dirk Griesbach <spamthis@freenet.de> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: 3.6+ <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-05-22libata: make ata_exec_internal_sg honor DMADIRVincent Pelletier
libata honors DMADIR for regular commands, but not for internal commands used (among other) during device initialisation. This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611 (such as "Abit Serillel 2") end up disabled when used with an ATAPI device after a few tries. Log output of the bridge being hot-plugged with an ATAPI drive: [ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen [ 9631.212913] ata1: irq_stat 0x00000040, connection status changed [ 9631.212923] ata1: SError: { CommWake 10B8B DevExch } [ 9631.212939] ata1: hard resetting link [ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33 [ 9632.106407] ata1.00: applying bridge limits [ 9632.108151] ata1.00: configured for UDMA/33 [ 9637.105303] ata1.00: qc timeout (cmd 0xa0) [ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9637.105335] ata1: hard resetting link [ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9638.047878] ata1.00: configured for UDMA/33 [ 9643.044933] ata1.00: qc timeout (cmd 0xa0) [ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps [ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3 [ 9643.044979] ata1: hard resetting link [ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 9643.987471] ata1.00: configured for UDMA/33 [ 9648.984591] ata1.00: qc timeout (cmd 0xa0) [ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9648.984619] ata1.00: disabled [ 9649.000593] ata1: hard resetting link [ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 9649.955864] ata1: EH complete With this patch, the drive enumerates correctly when libata is loaded with atapi_dmadir=1: [ 9891.810863] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen [ 9891.810874] ata1: irq_stat 0x00000040, connection status changed [ 9891.810884] ata1: SError: { CommWake 10B8B DevExch } [ 9891.810900] ata1: hard resetting link [ 9892.762105] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9892.763544] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33, DMADIR [ 9892.763558] ata1.00: applying bridge limits [ 9892.765393] ata1.00: configured for UDMA/33 [ 9892.786063] ata1: EH complete [ 9892.792062] scsi 0:0:0:0: CD-ROM PIONEER DVD-RW DVR-115 1.06 PQ: 0 ANSI: 5 [ 9892.798455] sr2: scsi3-mmc drive: 12x/12x writer dvd-ram cd/rw xa/form2 cdda tray [ 9892.798837] sr 0:0:0:0: Attached scsi CD-ROM sr2 [ 9892.799109] sr 0:0:0:0: Attached scsi generic sg6 type 5 Based on a patch by Csaba Halász <csaba.halasz@gmail.com> on linux-ide: http://marc.info/?l=linux-ide&m=136121147832295&w=2 tj: minor formatting changes. Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
2013-05-14libata: update "Maintained by:" tagsTejun Heo
Jeff moved on to a greener pasture. s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jeff Garzik <jgarzik@pobox.com>
2013-04-03libata: fix DMA to stack in reading devslp_timing parametersDavid Woodhouse
Commit 803739d25c2343da6d2f95eebdcbc08bf67097d4 ("[libata] replace sata_settings with devslp_timing"), which was also Cc: stable, used a stack buffer to receive data from ata_read_log_page(), which triggers the following warning: ahci 0000:00:1f.2: DMA-API: device driver maps memory fromstack [addr=ffff880140469948] Fix this by using ap->sector_buf instead of a stack buffer. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-04-03libata: Set max sector to 65535 for Slimtype DVD A DS8A8SH driveShan Hai
The Slimtype DVD A DS8A8SH drive locks up when max sector is smaller than 65535, and the blow backtrace is observed on locking up: INFO: task flush-8:32:1130 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. flush-8:32 D ffffffff8180cf60 0 1130 2 0x00000000 ffff880273aef618 0000000000000046 0000000000000005 ffff880273aee000 ffff880273aee000 ffff880273aeffd8 ffff880273aee010 ffff880273aee000 ffff880273aeffd8 ffff880273aee000 ffff88026e842ea0 ffff880274a10000 Call Trace: [<ffffffff8168fc2d>] schedule+0x5d/0x70 [<ffffffff8168fccc>] io_schedule+0x8c/0xd0 [<ffffffff81324461>] get_request+0x731/0x7d0 [<ffffffff8133dc60>] ? cfq_allow_merge+0x50/0x90 [<ffffffff81083aa0>] ? wake_up_bit+0x40/0x40 [<ffffffff81320443>] ? bio_attempt_back_merge+0x33/0x110 [<ffffffff813248ea>] blk_queue_bio+0x23a/0x3f0 [<ffffffff81322176>] generic_make_request+0xc6/0x120 [<ffffffff81322308>] submit_bio+0x138/0x160 [<ffffffff811d7596>] ? bio_alloc_bioset+0x96/0x120 [<ffffffff811d1f61>] submit_bh+0x1f1/0x220 [<ffffffff811d48b8>] __block_write_full_page+0x228/0x340 [<ffffffff811d3650>] ? attach_nobh_buffers+0xc0/0xc0 [<ffffffff811d8960>] ? I_BDEV+0x10/0x10 [<ffffffff811d8960>] ? I_BDEV+0x10/0x10 [<ffffffff811d4ab6>] block_write_full_page_endio+0xe6/0x100 [<ffffffff811d4ae5>] block_write_full_page+0x15/0x20 [<ffffffff811d9268>] blkdev_writepage+0x18/0x20 [<ffffffff81142527>] __writepage+0x17/0x40 [<ffffffff811438ba>] write_cache_pages+0x34a/0x4a0 [<ffffffff81142510>] ? set_page_dirty+0x70/0x70 [<ffffffff81143a61>] generic_writepages+0x51/0x80 [<ffffffff81143ab0>] do_writepages+0x20/0x50 [<ffffffff811c9ed6>] __writeback_single_inode+0xa6/0x2b0 [<ffffffff811ca861>] writeback_sb_inodes+0x311/0x4d0 [<ffffffff811caaa6>] __writeback_inodes_wb+0x86/0xd0 [<ffffffff811cad43>] wb_writeback+0x1a3/0x330 [<ffffffff816916cf>] ? _raw_spin_lock_irqsave+0x3f/0x50 [<ffffffff811b8362>] ? get_nr_inodes+0x52/0x70 [<ffffffff811cb0ac>] wb_do_writeback+0x1dc/0x260 [<ffffffff8168dd34>] ? schedule_timeout+0x204/0x240 [<ffffffff811cb232>] bdi_writeback_thread+0x102/0x2b0 [<ffffffff811cb130>] ? wb_do_writeback+0x260/0x260 [<ffffffff81083550>] kthread+0xc0/0xd0 [<ffffffff81083490>] ? kthread_worker_fn+0x1b0/0x1b0 [<ffffffff8169a3ec>] ret_from_fork+0x7c/0xb0 [<ffffffff81083490>] ? kthread_worker_fn+0x1b0/0x1b0 The above trace was triggered by "dd if=/dev/zero of=/dev/sr0 bs=2048 count=32768" It was previously working by accident, since another bug introduced by 4dce8ba94c7 (libata: Use 'bool' return value for ata_id_XXX) caused all drives to use maxsect=65535. Cc: stable@vger.kernel.org Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-25[libata] PM code cleanup for ata portAaron Lu
For system freeze, if the port is already runtime suspended, leave it alone and just return. The port will be resumed on thaw before it will be used. And since we will call get_noresume for every device during prepare phase, and the port is resumed during thaw phase, it can't be in runtime suspended state during the poweroff phase. So remove the runtime_suspended check in poweroff callback. And for all suspend(freeze/suspend/poweroff/etc.), there is no need to touch the device, so set no_autopsy and no_recovery for them all. Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-25[libata] pm: differentiate system and runtime pm for ata portAaron Lu
We need to do different things for system PM and runtime PM, e.g. we do not need to enable runtime wake for ZPODD when we are doing system suspend, etc. Currently, we use PMSG_SUSPEND for both system suspend and runtime suspend and PMSG_ON for both system resume and runtime resume. Change this by using PMSG_AUTO_SUSPEND for runtime suspend and PMSG_AUTO_RESUME for runtime resume. And since PMSG_ON means no transition, it is changed to PMSG_RESUME for ata port's system resume. The ata_acpi_set_state is modified accordingly, and the sata case and pata case is seperated for easy reading. Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-25Revert "libata: export host controller number thru /sys"Jeff Garzik
This reverts commit 1757d902b029a29dfcef63609964385cf8865b5a. Discussion continues upstream.
2013-01-21libata: do not suspend port if normal ODD is attachedAaron Lu
For ODDs, the upper layer will poll for media change every few seconds, which will make it enter and leave suspend state very often. And as each suspend will also cause a hard/soft reset, the gain of runtime suspend is very little while the ODD may malfunction after constantly being reset. So the idle callback here will not proceed to suspend if a non-ZPODD capable ODD is attached to the port. Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-21libata: identify and init ZPODD devicesAaron Lu
The ODD can be enabled for ZPODD if the following three conditions are satisfied: 1 The ODD supports device attention; 2 The platform can runtime power off the ODD through ACPI; 3 The ODD is either slot type or drawer type. For such ODDs, zpodd_init is called and a new structure is allocated for it to store ZPODD related stuffs. And the zpodd_dev_enabled function is used to test if ZPODD is currently enabled for this ODD. A new config CONFIG_SATA_ZPODD is added to selectively build ZPODD code. Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-14libata: export host controller number thru /sysDavid Milburn
As low-level drivers register their host controller(s), keep track of the number of controllers and export thru /sys in a <host.port> format so that udev can better match up port numbers with a specific controller. # pwd /sys/devices/pci0000:00 # find . -name 'ata*' -print (2nd controller with port multiplier attached) ./0000:00:1e.0/0000:05:01.0/ata2.7 ./0000:00:1e.0/0000:05:01.0/ata2.7/link7/dev7.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.0/dev7.0.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.0/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.1/dev7.1.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.1/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.2/dev7.2.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.2/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.3/dev7.3.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.3/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.4/dev7.4.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.4/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.5/dev7.5.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.5/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.6/dev7.6.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.6/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.7/dev7.7.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.7/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.8/dev7.8.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.8/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.9/dev7.9.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.9/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/ata_port ./0000:00:1e.0/0000:05:01.0/ata2.7/ata_port/ata2.7 ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.10/dev7.10.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.10/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.11/dev7.11.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.11/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.12/dev7.12.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.12/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.13/dev7.13.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.13/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.14/dev7.14.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.7/link7.14/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.8 ./0000:00:1e.0/0000:05:01.0/ata2.8/link8/dev8.0/ata_device ./0000:00:1e.0/0000:05:01.0/ata2.8/link8/ata_link ./0000:00:1e.0/0000:05:01.0/ata2.8/ata_port ./0000:00:1e.0/0000:05:01.0/ata2.8/ata_port/ata2.8 (1st controller) ./0000:00:1f.2/ata1.1 ./0000:00:1f.2/ata1.1/link1/dev1.0/ata_device ./0000:00:1f.2/ata1.1/link1/ata_link ./0000:00:1f.2/ata1.1/ata_port ./0000:00:1f.2/ata1.1/ata_port/ata1.1 ./0000:00:1f.2/ata1.2 ./0000:00:1f.2/ata1.2/link2/dev2.0/ata_device ./0000:00:1f.2/ata1.2/link2/ata_link ./0000:00:1f.2/ata1.2/ata_port ./0000:00:1f.2/ata1.2/ata_port/ata1.2 ./0000:00:1f.2/ata1.3 ./0000:00:1f.2/ata1.3/link3/dev3.0/ata_device ./0000:00:1f.2/ata1.3/link3/ata_link ./0000:00:1f.2/ata1.3/ata_port ./0000:00:1f.2/ata1.3/ata_port/ata1.3 ./0000:00:1f.2/ata1.4 ./0000:00:1f.2/ata1.4/link4/dev4.0/ata_device ./0000:00:1f.2/ata1.4/link4/ata_link ./0000:00:1f.2/ata1.4/ata_port ./0000:00:1f.2/ata1.4/ata_port/ata1.4 ./0000:00:1f.2/ata1.5 ./0000:00:1f.2/ata1.5/link5/dev5.0/ata_device ./0000:00:1f.2/ata1.5/link5/ata_link ./0000:00:1f.2/ata1.5/ata_port ./0000:00:1f.2/ata1.5/ata_port/ata1.5 ./0000:00:1f.2/ata1.6 ./0000:00:1f.2/ata1.6/link6/dev6.0/ata_device ./0000:00:1f.2/ata1.6/link6/ata_link ./0000:00:1f.2/ata1.6/ata_port ./0000:00:1f.2/ata1.6/ata_port/ata1.6 Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-14[libata] replace sata_settings with devslp_timingShane Huang
NCQ capability was used to check availability of SATA Settings page from Identify Device Data Log, which contains DevSlp timing variables. It does not work on some HDDs and leads to error messages. IDENTIFY word 78 bit 5(Hardware Feature Control) can't work either because it is only the sufficient condition of Identify Device data log, not the necessary condition. This patch replaced ata_device->sata_settings with ->devslp_timing to only save DevSlp timing variables(8 bytes), instead of the whole SATA Settings page(512 bytes). Addresses https://bugzilla.kernel.org/show_bug.cgi?id=51881 Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Shane Huang <shane.huang@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-12-14Revert "libata: check SATA_SETTINGS log with HW Feature Ctrl"Jeff Garzik
This reverts commit de90cd71f68e947d3bd6c3f2ef5731ead010a768. Shane Huang writes: Please suspend this patch because I just received two new DevSlp drives but found word 78 bit 5 is _not_ set. I'm checking with the drive vendor whether he gave me the wrong information. If bit 5 is not the necessary and sufficient condition, I will implement another patch to replace ata_device->sata_settings into ->devslp_timing. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-12-03libata: use pci_get_drvdata() helperBrian Norris
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-12-03libata: implement ata_platform_remove_one()Brian Norris
This relatively simple boiler-plate code is repeated in several platform drivers. We should implement a common version in libata. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-12-03libata: set dma_mode to 0xff in resetAaron Lu
ata_device->dma_mode's initial value is zero, which is not a valid dma mode, but ata_dma_enabled will return true for this value. This patch sets dma_mode to 0xff in reset function, so that ata_dma_enabled will not return true for this case, or it will cause problem for pata_acpi. The corrsponding bugzilla page is at: https://bugzilla.kernel.org/show_bug.cgi?id=49151 Reported-by: Phillip Wood <phillip.wood@dunelm.org.uk> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Tested-by: Szymon Janc <szymon@janc.net.pl> Tested-by: Dutra Julio <dutra.julio@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Cc: <stable@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-12-03libata: check SATA_SETTINGS log with HW Feature CtrlShane Huang
NCQ capability was used to check availability of SATA Settings page from Identify Device Data Log, which contains DevSlp timing variables. It does not work on some HDDs and leads to error messages. IDENTIFY word 78 bit 5(Hardware Feature Control) should be used. Quoting SATA spec 3.1: If Hardware Feature Control is supported, then: a) IDENTIFY DEVICE data word 78 bit 5 (see 13.2.1.18) shall be set to one; b) the SET FEATURES Select Hardware Feature Control subcommand shall be supported (see 13.3.8); c) page 08h of the Identify Device Data log (see 13.7.7) shall be supported; This patch is not tested on SATA HDD with DevSlp supported. Reported-by: Borislav Petkov <bp@amd64.org> Signed-off-by: Shane Huang <shane.huang@amd.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-11-15libata debugging: Warn when unable to find timing descriptor based on xfer_modeBorislav Petkov
ata_timing_find_mode could return NULL which is not checked by all low-level ATA drivers using it and cause a NULL ptr deref. Warn at least so that possible issues can get fixed easily. Signed-off-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-10-02Merge tag 'scsi-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull first round of SCSI updates from James Bottomley: "This is a large set of updates, mostly for drivers (qla2xxx [including support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape adding virtually unlimited numbers of tape drives plus a set of dif fixes for sd and a fix for a live lock on hot remove of SCSI devices. This round includes a signed tag pull of isci-for-3.6 Signed-off-by: James Bottomley <JBottomley@Parallels.com>" Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI helper function use in a function that was removed by this pull. * tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits) [SCSI] st: remove st_mutex [SCSI] sd: Ensure we correctly disable devices with unknown protection type [SCSI] hpsa: gen8plus Smart Array IDs [SCSI] qla4xxx: Update driver version to 5.03.00-k1 [SCSI] qla4xxx: Disable generating pause frames for ISP83XX [SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX [SCSI] qla4xxx: IDC implementation for Loopback [SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx [SCSI] qla4xxx: Fix panic while rmmod [SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails [SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX [SCSI] qla4xxx: Update idc reg in case of PCI AER [SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery [SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX [SCSI] qla4xxx: Print correct IDC version [SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW [SCSI] scsi_dh_alua: Enable STPG for unavailable ports [SCSI] scsi_remove_target: fix softlockup regression on hot remove [SCSI] ibmvscsi: Fix host config length field overflow [SCSI] ibmvscsi: Remove backend abstraction ...
2012-10-02Merge tag 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev Pull libata changes from Jeff Garzik: "Minor libata updates, nothing notable. 1) Apply -- and then revert -- the FUA feature. Caused disk corruption in linux-next, proving it cannot be turned on by default. Net effect to upstream tree: zero 2) New AHCI platform driver sata_highbank 3) Improve SCSI MODE SENSE handling; support MODE SELECT 4) AHCI: support aggressive device sleep (power mgmt) 5) sata_fsl: minor fix 6) pata_arasan: clk support" * tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: sata_mv: Fix warnings when no PCI [libata] Makefile: Fix build error in sata_highbank [libata] export ata_dev_set_feature() libata-core: use ATA_LBA in ata_build_rw_tf() ata/ahci_platform: Add clock framework support pata_arasan: add Device Tree probing capability pata_arasan: Add clk_{un}prepare() support ata: add platform driver for Calxeda AHCI controller sata_fsl: add workaround for data length mismatch on freescale V2 controller ahci: implement aggressive SATA device sleep support ata: define enum constants for IDENTIFY DEVICE Revert "libata: enable SATA disk fua detection on default" [libata] scsi: implement MODE SELECT command [libata] scsi: support MODE SENSE request for changeable and default parameters [libata] scsi: Remove unlikely() from FUA check libata: enable SATA disk fua detection on default
2012-10-02Merge SCSI misc branch into isci-for-3.6 tagJames Bottomley
2012-09-13[libata] export ata_dev_set_feature()Jeff Garzik
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-09-13libata-core: use ATA_LBA in ata_build_rw_tf()Sergei Shtylyov
Since READ/WRITE FPDMA QUEUED commands are 48-bit, bit 6 of the device register means LBA, the same as for READ/WRITE DMA EXT commands. So use ATA_LBA instead of the bare number in ata_build_rw_tf()'s branch dedicated to the NCQ commands. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-09-13ahci: implement aggressive SATA device sleep supportShane Huang
Device Sleep is a feature as described in AHCI 1.3.1 Technical Proposal. This feature enables an HBA and SATA storage device to enter the DevSleep interface state, enabling lower power SATA-based systems. Aggressive Device Sleep enables the HBA to assert the DEVSLP signal as soon as there are no commands outstanding to the device and the port specific Device Sleep idle timer has expired. This enables autonomous entry into the DevSleep interface state without waiting for software in power sensitive systems. This patch enables Aggressive Device Sleep only if both host controller and device support it. Tested on AMD reference board together with Device Sleep supported device sample. Signed-off-by: Shane Huang <shane.huang@amd.com> Reviewed-by: Aaron Lu <aaron.lwe@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-09-13Revert "libata: enable SATA disk fua detection on default"Jeff Garzik
It caused several reported regressions. This reverts commit 91895b786e631ab47b618c901231f22b5a44115b.
2012-08-25libata: Add a space to " 2GB ATA Flash Disk" DMA blacklist entryPrarit Bhargava
commit d70e551c8e1ecb6f20422f8db6bfe6a0049edcb8, Add " 2GB ATA Flash Disk"/"ADMA428M" to DMA blacklist, should have added a space before 2GB. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-08-24[SCSI] libsas, ipr: cleanup ata_host flags initialization via ata_host_initDan Williams
libsas and ipr pass flags to ata_host_init that are meant for the port. ata_host flags: ATA_HOST_SIMPLEX = (1 << 0), /* Host is simplex, one DMA channel per host only */ ATA_HOST_STARTED = (1 << 1), /* Host started */ ATA_HOST_PARALLEL_SCAN = (1 << 2), /* Ports on this host can be scanned in parallel */ ATA_HOST_IGNORE_ATA = (1 << 3), /* Ignore ATA devices on this host. */ flags passed by libsas: ATA_FLAG_SATA = (1 << 1), ATA_FLAG_PIO_DMA = (1 << 7), /* PIO cmds via DMA */ ATA_FLAG_NCQ = (1 << 10), /* host supports NCQ */ The only one that aliases is ATA_HOST_STARTED which is a 'don't care' in the libsas and ipr cases since ata_hosts from these sources are not registered with libata. Reported-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Brian King <brking@us.ibm.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-08-24[SCSI] libata: export ata_port suspend/resume infrastructure for sasDan Williams
Reuse ata_port_{suspend|resume}_common for sas. This path is chosen over adding coordination between ata-tranport and sas-transport because libsas wants to revalidate the domain at resume-time at the host level. It can not validate links have resumed properly until libata has had a chance to perform its revalidation, and any sane placing of an ata_port in the sas-transport model would delay it's resumption until after the host. Export the common portion of port suspend/resume (bypass pm_runtime), and allow sas to perform these operations asynchronously (similar to the libsas async-ata probe implmentation). Async operation is determined by having an external, rather than stack based, location for storing the result of the operation. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jacek Danecki <jacek.danecki@intel.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-08-24[SCSI] libata: reset onceDan Williams
Hotplug testing with libsas currently encounters a 55 second wait for link recovery to give up. In the case where the user trusts the response time of their devices permit the recovery attempts to be limited to one. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-08-17libata: enable SATA disk fua detection on defaultZheng Liu
Currently, SATA disk fua detection is disabled on default because most of devices don't support this feature at that time. With the development of technology, more and more SATA disks support this feature. So now we can enable this detection on default. Although fua detection is defined as a kernel module parameter, it is too hard to set its value because it must be loaded and set before system starts up. That needs to modify initrd file. So it is inconvenient for administrator who needs to manage a huge number of servers. Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-08-17[libata] new quirk, lift bridge limits for Buffalo DriveStation QuattroJeff Garzik
Michael Eitelwein writes: I have an external SATA drive that was slowed down by bridge limits. I found a solution in a thread on this list posted in 2008: It introduces whitelist entries in libata-core.c for devices with well working bridges (e.g. email on Fri, 31 Oct 2008 01:45:27 -0400). I added my device to this whitelist in a custom built kernel and it works fine for weeks now. How can I have this device added on the whitelist within the official kernel? Is this whitelist mechanism still supported or is there a smarter way to achieve whitelisting? I added the following whitelist entry for my Buffalo DriveStation Quattro "BUFFALO HD-QSU2/R5": /* Devices that do not need bridging limits applied */ { "MTRON MSP-SATA*", NULL, ATA_HORKAGE_BRIDGE_OK, }, { "BUFFALO HD-QSU2/R5", NULL, ATA_HORKAGE_BRIDGE_OK, }, Reported-by: Michael Eitelwein <michael@eitelwein.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-07-25Merge branch 'master' [vanilla Linus master] into libata-dev.git/upstreamJeff Garzik
Two bits were appended to the end of the bitfield list in struct scsi_device. Resolve that conflict by including both bits. Conflicts: include/scsi/scsi_device.h
2012-07-25[libata] Prevent interface errors with Seagate FreeAgent GoFlexDaniel J Blueman
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure, interface errors are always seen until 1.5Gbps is negotiated [1]. This occurs using any disk in the enclosure, and when the disk is connected directly with a generic passive eSATAp cable, we see stable 3Gbps operation as expected. Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset and renegotiation incurs. Signed-off-by: Daniel J Blueman <daniel@quora.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-07-20[SCSI] libata, libsas: introduce sched_eh and end_eh port opsDan Williams
When managing shost->host_eh_scheduled libata assumes that there is a 1:1 shost-to-ata_port relationship. libsas creates a 1:N relationship so it needs to manage host_eh_scheduled cumulatively at the host level. The sched_eh and end_eh port port ops allow libsas to track when domain devices enter/leave the "eh-pending" state under ha->lock (previously named ha->state_lock, but it is no longer just a lock for ha->state changes). Since host_eh_scheduled indicates eh without backing commands pinning the device it can be deallocated at any time. Move the taking of the domain_device reference under the port_lock to guarantee that the ata_port stays around for the duration of eh. Reviewed-by: Jacek Danecki <jacek.danecki@intel.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-06-29libata: detect Device Attention supportLin Ming
Add a new flag ATA_DFLAG_DA to indicate that device supports "Device Attention". Acked-by: Aaron Lu <aaron.lu@amd.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-06-29libata: migrate ACPI code over to new bindingsMatthew Garrett
Now that we have the ability to directly glue the ACPI namespace to the driver model in libata, we don't need the custom code to handle the same thing. Remove it and migrate the functions over to the new code. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Holger Macht <holger@homac.de> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-06-29libata: bind the Linux device tree to the ACPI device treeMatthew Garrett
Associate the ACPI device tree and libata devices. This patch uses the generic ACPI glue framework to do so. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Holger Macht <holger@homac.de> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-05-22[libata] Add " 2GB ATA Flash Disk"/"ADMA428M" to DMA blacklistPrarit Bhargava
A user has several systems with a couple of models of flash disks with IDE connectors. These disks work fine in 2.6.18-ish kernels but corrupt data on new kernels. The difference appears to be with the default I/O method used by the IDE controller driver between the kernels. In the older kernels, the configuration is very conservative and the driver stays in PIO mode. With new kernels, the ata driver (pata_serverworks) attempts to use UDMA/66 which the drive claims to support. This mode, however, does not appear to work in DMA mode. The drive does work correctly and no corruption is seen if the kernel parameter "libata.force=5:pio0,6:pio0" is used to force the driver to use PIO instead of DMA mode. Blacklist these drives. Unfortunately the model name of the drive is very generic, " 2GB ATA Flash Disk", but the revision is specific, "ADMA428M". Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-05-07libata: add a host flag to ignore detected ATA devicesAndy Whitcroft
Where devices are visible via more than one host we sometimes wish to indicate that cirtain devices should be ignored on a specific host. Add a host flag indicating that this host wishes to ignore ATA specific devices. Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-05-03libata: init ata_print_id to 0Tero Roponen
When comparing the dmesg between 3.4-rc3 and 3.4-rc4 I found the following differences: -ata1: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47 -ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47 -ata3: DUMMY +ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47 +ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47 ata4: DUMMY ata5: DUMMY -ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47 +ata6: DUMMY +ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47 The change of numbering comes from commit 85d6725b7c0d7e3f ("libata: make ata_print_id atomic") that changed lines like ap->print_id = ata_print_id++; to ap->print_id = atomic_inc_return(&ata_print_id); As the latter behaves like ++ata_print_id, we must initialize it to zero to start the numbering from one. Signed-off-by: Tero Roponen <tero.roponen@gmail.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>