| Age | Commit message (Collapse) | Author |
|---|
|
Make the timer frequency selectable. The timer interrupt may cause bus
and memory contention in large NUMA systems since the interrupt occurs
on each processor HZ times per second.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Allow early printk code to take advantage of the full size of the screen, not
just the first 25 lines.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Get the i386 watchdog tick calculation into a state where it can also be used
on CPUs with frequencies beyond 4GHz, and it consolidates the calculation into
a single place (for potential furture adjustments).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch is per Andi's request to remove NO_IOAPIC_CHECK from genapic and
use heuristics to prevent unique I/O APIC ID check for systems that don't
need it. The patch disables unique I/O APIC ID check for Xeon-based and
other platforms that don't use serial APIC bus for interrupt delivery.
Andi stated that AMD systems don't need unique IO_APIC_IDs either.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This problem was first noticed on PPC and has already been fixed there.
But the exact same issue applies to other platforms in the same way. The
signal blocking for sa_mask and the handled signal takes place after the
handler setup. When the stack is bogus, the handler setup forces a
SIGSEGV. But then this will be blocked, and returning to user mode will
fault again and iterate. This patch fixes the problem by checking whether
signal handler setup failed, and not doing the signal-blocking if so. This
copies what was done in the ppc code. I think all architectures' signal
handler setup code follows this pattern and needs the change.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Define pcibus_to_node to be able to figure out which NUMA node contains a
given PCI device. This defines pcibus_to_node(bus) in
include/linux/topology.h and adjusts the macros for i386 and x86_64 that
already provided a way to determine the cpumask of a pci device.
x86_64 was changed to not build an array of cpumasks anymore. Instead an
array of nodes is build which can be used to generate the cpumask via
node_to_cpumask.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Issue:
Current tsc based delay_calibration can result in significant errors in
loops_per_jiffy count when the platform events like SMIs
(System Management Interrupts that are non-maskable) are present. This could
lead to potential kernel panic(). This issue is becoming more visible with 2.6
kernel (as default HZ is 1000) and on platforms with higher SMI handling
latencies. During the boot time, SMIs are mostly used by BIOS (for things
like legacy keyboard emulation).
Description:
The psuedocode for current delay calibration with tsc based delay looks like
(0) Estimate a value for loops_per_jiffy
(1) While (loops_per_jiffy estimate is accurate enough)
(2) wait for jiffy transition (jiffy1)
(3) Note down current tsc (tsc1)
(4) loop until tsc becomes tsc1 + loops_per_jiffy
(5) check whether jiffy changed since jiffy1 or not and refine
loops_per_jiffy estimate
Consider the following cases
Case 1:
If SMIs happen between (2) and (3) above, we can end up with a
loops_per_jiffy value that is too low. This results in shorted delays and
kernel can panic () during boot (Mostly at IOAPIC timer initialization
timer_irq_works() as we don't have enough timer interrupts in a specified
interval).
Case 2:
If SMIs happen between (3) and (4) above, then we can end up with a
loops_per_jiffy value that is too high. And with current i386 code, too
high lpj value (greater than 17M) can result in a overflow in
delay.c:__const_udelay() again resulting in shorter delay and panic().
Solution:
The patch below makes the calibration routine aware of asynchronous events
like SMIs. We increase the delay calibration time and also identify any
significant errors (greater than 12.5%) in the calibration and notify it to
user.
Patch below changes both i386 and x86-64 architectures to use this
new and improved calibrate_delay_direct() routine.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The attached patch causes the various arch specific install.sh scripts to
look for ${CROSS_COMPILE}installkernel rather than just installkernel (in
both /sbin/ and ~/bin/ where the script already did this). This allows you
to have e.g. arm-linux-installkernel as a handy way to install on your
cross target. It also prevents the script picking up on the host
/sbin/installkernel which causes the script to fall through and do the
install itself (which is what I actually use myself, with $INSTALL_PATH
set).
I don't believe it causes back-compatibility problems since calling the
host installkernel was never likely to work or be what you wanted when
cross compiling anyway. If $CROSS_COMPILE isn't set then nothing changes.
I only use ARM and i386 myself but I figured it couldn't hurt to do the
whole lot. I've cc'd those who I hope are the arch maintainers for files
that I've touched.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This allows the i386 architecture to be built on a system with a biarch
compiler that defaults to x86-64, merely by specifying ARCH=i386.
As previously discussed, this uses the equivalent logic to the ppc port.
Signed-Off-By: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This helps a lot when debugging out of memory stuff - useful especially to
see if all the memory is sucked into slab, etc.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds in the necessary support for sparsemem such that x86-64
kernels may use sparsemem as an alternative to discontigmem for NUMA
kernels. Note that this does no preclude one from continuing to build NUMA
kernels using discontigmem, but merely allows the option to build NUMA
kernels with sparsemem.
Interestingly, the use of sparsemem in lieu of discontigmem in NUMA kernels
results in reduced text size for otherwise equivalent kernels as shown in
the example builds below:
text data bss dec hex filename
2371036 765884 1237108 4374028 42be0c vmlinux.discontig
2366549 776484 1302772 4445805 43d66d vmlinux.sparse
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In order to use the alternative sparsemem implmentation for NUMA kernels,
we need to reorganize the config options. This patch effectively abstracts
out the CONFIG_DISCONTIGMEM options to CONFIG_NUMA in most cases. Thus,
the discontigmem implementation may be employed as always, but the
sparsemem implementation may be used alternatively.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add the requisite arch specific Kconfig options to enable the use of the
sparsemem implementation for NUMA kernels on x86-64.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch pulls out all remaining direct references to contig_page_data
from arch/x86-64, thus saving an ifdef in one case.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Provide the architecture specific implementation for SPARSEMEM for PPC64
systems.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com> (in part)
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Provide hooks for PPC64 to allow memory models to be informed of installed
memory areas. This allows SPARSEMEM to instantiate mem_map for the populated
areas.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Provide an implementation of early_pfn_to_nid for PPC64. This is used by
memory models to determine the node from which to take allocations before the
memory allocators are fully initialised.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The part of the sparsemem patch which modifies memmap_init_zone() has recently
become a problem. It changes behavior so that there is a call to
pfn_to_page() for each individual page inside of a node's range:
node_start_pfn through node_end_pfn. It used to simply do this once, at the
beginning of the node, but having sparsemem's non-contiguous mem_map[]s inside
of a node made it necessary to change.
Mike Kravetz recently wrote a patch which made the NUMA code accept some new
kinds of layouts. The system's memory was laid out like this, with node 0's
memory in two pieces: one before and one after node 1's memory:
Node 0: +++++ +++++
Node 1: +++++
Previous behavior before Mike's patch was to assign nodes like this:
Node 0: 00000 XXXXX
Node 1: 11111
Where the 'X' areas were simply thrown away. The new behavior was to make the
pg_data_t span node 0 across all of its areas, including areas that are really
node 1's: Node 0: 000000000000000 Node 1: 11111
This wastes a little bit of mem_map space, but ends up being OK, and more
fully utilizes the system's memory. memmap_init_zone() initializes all of the
"struct page"s for node 0, even for the "hole", but those never get used,
because there is no pfn_to_page() that resolves to those pages. However, only
calling pfn_to_page() once, memmap_init_zone() always uses the pages that were
allocated for node0->node_mem_map because:
struct page *start = pfn_to_page(start_pfn);
// effectively start = &node->node_mem_map[0]
for (page = start; page < (start + size); page++) {
init_page_here();...
page++;
}
Slow, and wasteful, but generally harmless.
But, modify that to call pfn_to_page() for each loop iteration (like sparsemem
does):
for (pfn = start_pfn; pfn < < (start_pfn + size); pfn++++) {
page = pfn_to_page(pfn);
}
And you end up trying to initialize node 1's pages too early, along with bogus
data from node 0. This patch checks for those weird layouts and declines to
touch the pages, making the more frequent pfn_to_page() calls OK to do.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Provide the architecture specific implementation for SPARSEMEM for i386 SMP
and NUMA systems.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of
mem_map[] is needed by discontiguous memory machines (like in the old
CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem
replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually
become a complete replacement.
A significant advantage over DISCONTIGMEM is that it's completely separated
from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA
and DISCONTIG are often confused.
Another advantage is that sparse doesn't require each NUMA node's ranges to be
contiguous. It can handle overlapping ranges between nodes with no problems,
where DISCONTIGMEM currently throws away that memory.
Sparsemem uses an array to provide different pfn_to_page() translations for
each SECTION_SIZE area of physical memory. This is what allows the mem_map[]
to be chopped up.
In order to do quick pfn_to_page() operations, the section number of the page
is encoded in page->flags. Part of the sparsemem infrastructure enables
sharing of these bits more dynamically (at compile-time) between the
page_zone() and sparsemem operations. However, on 32-bit architectures, the
number of bits is quite limited, and may require growing the size of the
page->flags type in certain conditions. Several things might force this to
occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of
memory), an increase in the physical address space, or an increase in the
number of used page->flags.
One thing to note is that, once sparsemem is present, the NUMA node
information no longer needs to be stored in the page->flags. It might provide
speed increases on certain platforms and will be stored there if there is
room. But, if out of room, an alternate (theoretically slower) mechanism is
used.
This patch introduces CONFIG_FLATMEM. It is used in almost all cases where
there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM
often have to compile out the same areas of code.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Allow architectures to indicate that they will be providing hooks to indice
installed memory areas, memory_present(). Provide prototypes for the i386
implementation.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Provide a default implementation for early_pfn_to_nid returning node 0. Allow
architectures to override this with their own implementation out of
asm/mmzone.h.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch changes some of the default behavior in the ppc64 Kconfig file
that was recently changed/added to 2.6.12-rc2-mm1 by Dave Hansen in
preparation for SPARSEMEM. Patch allows the display of both FLAT and
DISCONTIG models on pseries. As before, default is DISCONTIG for SMP and
PSERIES and FLAT for others.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This used to be used to disable FLATMEM selection, but I decided to change it
to be done generically when DISCONTIG is enabled. The option is unused, so
this kills it.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This will at least suppress one prompt that users would have received the
first time they compile with the new DISCONTIG arch option. They'll still
get the "Memory Model" prompt, but 99% of them will have the default work
there.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
For all architectures, this just means that you'll see a "Memory Model"
choice in your architecture menu. For those that implement DISCONTIGMEM,
you may eventually want to make your ARCH_DISCONTIGMEM_ENABLE a "def_bool
y" and make your users select DISCONTIGMEM right out of the new choice
menu. The only disadvantage might be if you have some specific things that
you need in your help option to explain something about DISCONTIGMEM.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
discontig.c has some assumptions that mem_map[]s inside of a node are
contiguous. Teach it to make sure that each region that it's bringing online
is actually made up of valid ranges of ram.
Written-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Introduce a simple allocator for the NUMA remap space. This space is very
scarce, used for structures which are best allocated node local.
This mechanism is also used on non-NUMA ia64 systems with a vmem_map to keep
the pgdat->node_mem_map initialized in a consistent place for all
architectures.
Issues:
o alloc_remap takes a node_id where we might expect a pgdat which was intended
to allow us to allocate the pgdat's using this mechanism; which we do not yet
do. Could have alloc_remap_node() and alloc_remap_nid() for this purpose.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The following four patches provide the last needed changes before the
introduction of sparsemem. For a more complete description of what this
will do, please see this patch:
http://www.sr71.net/patches/2.6.11/2.6.11-bk7-mhp1/broken-out/B-sparse-150-sparsemem.patch
or previous posts on the subject:
http://marc.theaimsgroup.com/?t=110868540700001&r=1&w=2
http://marc.theaimsgroup.com/?l=linux-mm&m=109897373315016&w=2
Three of these are i386-only, but one of them reorganizes the macros
used to manage the space in page->flags, and will affect all platforms.
There are analogous patches to the i386 ones for ppc64, ia64, and
x86_64, but those will be submitted by the normal arch maintainers.
The combination of the four patches has been test-booted on a variety of
i386 hardware, and compiled for ppc64, i386, and x86-64 with about 17
different .configs. It's also been runtime-tested on ia64 configs (with
more patches on top).
This patch:
We _know_ which node pages in general belong to, at least at a very gross
level in node_{start,end}_pfn[]. Use those to target the allocations of
pages.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch effectively eliminates direct use of pgdat->node_mem_map outside
of the DISCONTIG code. On a flat memory system, these fields aren't
currently used, neither are they on a sparsemem system.
There was also a node_mem_map(nid) macro on many architectures. Its use
along with the use of ->node_mem_map itself was not consistent. It has
been removed in favor of two new, more explicit, arch-independent macros:
pgdat_page_nr(pgdat, pagenr)
nid_page_nr(nid, pagenr)
I called them "pgdat" and "nid" because we overload the term "node" to mean
"NUMA node", "DISCONTIG node" or "pg_data_t" in very confusing ways. I
believe the newer names are much clearer.
These macros can be overridden in the sparsemem case with a theoretically
slower operation using node_start_pfn and pfn_to_page(), instead. We could
make this the only behavior if people want, but I don't want to change too
much at once. One thing at a time.
This patch removes more code than it adds.
Compile tested on alpha, alpha discontig, arm, arm-discontig, i386, i386
generic, NUMAQ, Summit, ppc64, ppc64 discontig, and x86_64. Full list
here: http://sr71.net/patches/2.6.12/2.6.12-rc1-mhp2/configs/
Boot tested on NUMAQ, x86 SMP and ppc64 power4/5 LPARs.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin J. Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
Since meminfo.bank[] array contains page-aligned start/size, we
no longer need to explicitly round up/down the addresses when
converting to PFNs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Ensure that meminfo.bank[] array contains page-aligned start/size
information.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert dmabounce.c to use list_for_each_entry() instead of
list_for_each() + list_entry().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Adding support for MPC8548 w/o PCI support, broke building MPC8555 CDS
by trying to remove a loop variable that was used when PCI is enabled.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org)
|
|
Move the signal return code into the vector page instead of placing
it on the user mode stack, which will allow us to avoid flushing
the instruction cache on signals, as well as eventually allowing
non-exec stack.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Do arch/ia64/defconfig by hand.
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This change provides support for the DS1374 Real-Time Clock chip present
on the MPC8349ADS board. It depends on a previous patch which adds I2C
support for the DS1374.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Wait for interrupt and clear status pending after resetting the reader.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The kernel takes a very long time to boot if the memory size is bigger then
32767 MB. The memory size is contained in a structure created by an sclp
call. The kernel accesses the field with a LH instrution which performs a
sign extension of a 16 bit word. In the case of a memory size with bit 2^15
set this results in a very large value and the memory detection just loops for
a long time. In addition if more then 64 GB are used on a 64 bit system the
memory size is read from an incorrect storage location.
Use zero-extention to read the 16 bit memory size and the correct offset to
read the 4 byte memory size on 64 bit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make cmm module parameter "sender" visible in sysfs.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
die() doesn't return, therefore print registers and then panic instead.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove superflous #if .. #endif pairs from compat_ioctl.c.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
To make sure switcheroo() can execute when we remap all the executable
image, we used a trick to make it use a local copy of errno... this trick
does not work with NPTL glibc, only with LinuxThreads, so use another
(simpler) one to make it work anyway.
Hopefully, a lot improved thanks to merging with the version of Al Viro
(which had his part of problems, though, i.e. removing a fix to another
bug and not fixing the problem on i386).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With Chris Wedgwood <cw@f00f.org>
As suggested by Chris, we can make the "just added" method ->release
conditional to UML only (better: to archs requesting it, i.e. only UML
currently), so that other archs don't get this unneeded crud, and if UML
won't need it any more we can kill this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This occurrence of free_irq_by_irq_and_dev() was missed when converting UML
to the use of hw_controller_type->release.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With Chris Wedgwood <cw@f00f.org>
Currently UML must explicitly call the UML-specific
free_irq_by_irq_and_dev() for each free_irq call it's done.
This is needed because ->shutdown and/or ->disable are only called when the
last "action" for that irq is removed.
Instead, for UML shared IRQs (UML IRQs are very often, if not always,
shared), for each dev_id some setup is done, which must be cleared on the
release of that fd. For instance, for each open console a new instance
(i.e. new dev_id) of the same IRQ is requested().
Exactly, a fd is stored in an array (pollfds), which is after read by a
host thread and passed to poll(). Each event registered by poll() triggers
an interrupt. So, for each free_irq() we must remove the corresponding
host fd from the table, which we do via this -release() method.
In this patch we add an appropriate hook for this, and remove all uses of
it by pointing the hook to the said procedure; this is safe to do since the
said procedure.
Also some cosmetic improvements are included.
This is heavily based on some work by Chris Wedgwood, which however didn't
get the patch merged for something I'd call a "misunderstanding" (the need
for this patch wasn't cleanly explained, thus adding the generic hook was
felt as undesirable).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
