aboutsummaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2013-10-06ARM: dts: Add fixed voltage regulator to simple bus for origenSachin Kamat
This has been done for Arndale board vide commit aa3edb65 ("ARM: dts: Put Arndale fixed voltage regulators on a simple-bus"). Replicate here for consistency and correctness. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2013-10-06ARM: dts: Add MIPI PHY node to exynos4.dtsiSylwester Nawrocki
Add PHY provider node for the MIPI CSIS and MIPI DSIM PHYs. Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Felipe Balbi <balbi@ti.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2013-09-20Merge tag 'pm+acpi-3.12-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI and power management fixes from Rafael Wysocki: 1) Four fixes for cpufreq regressions introduced by the changes that removed Device Tree parsing for CPU device nodes from cpufreq drivers from Sudeep KarkadaNagesha. 2) Two fixes for recent cpufreq regressions introduced by changes related to the preservation of sysfs attributes over system suspend/resume cycles from Viresh Kumar. 3) Fix for ACPI-based wakeup signaling in the PCI subsystem that fails to stop PME polling for devices put into the D3cold power state from Rafael J Wysocki. 4) Fix for bad interactions between cpufreq and udev on systems supporting intel_pstate where acpi-cpufreq is available as well from Yinghai Lu. * tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpufreq: return EEXIST instead of EBUSY for second registering PCI / ACPI / PM: Clear pme_poll for devices in D3cold on wakeup ARM: shmobile: change dev_id to cpu0 while registering cpu clock ARM: i.MX: change dev_id to cpu0 while registering cpu clock cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device cpufreq: cpufreq-cpu0: assign cpu_dev correctly to cpu0 device cpufreq: unlock correct rwsem while updating policy->cpu cpufreq: Clear policy->cpus bits in __cpufreq_remove_dev_finish()
2013-09-19ARM: shmobile: change dev_id to cpu0 while registering cpu clockSudeep KarkadaNagesha
Currently all clkdev registration use "cpufreq-cpu0.0" as dev_id for cpu clock which refers to virtual platform device. It needs to be "cpu0" instead which is actual cpu0 device id. This patch changes the dev_id from "cpufreq-cpu0.0" to "cpu0". Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Magnus Damm <damm@opensource.se> Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-09-19ARM: i.MX: change dev_id to cpu0 while registering cpu clockSudeep KarkadaNagesha
Currently all clkdev registration use "cpufreq-cpu0.0" as dev_id for cpu clock which refers to virtual platform device. It needs to be "cpu0" instead which is actual cpu0 device id. This patch changes the dev_id from "cpufreq-cpu0.0" to "cpu0". Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-09-19cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 deviceSudeep KarkadaNagesha
Commit cdc58d602d2e657602a90c190cbf745886c95977 "cpufreq: imx6q-cpufreq: remove device tree parsing for cpu nodes" assumed the pdev->dev is set to cpu0 device in the platform code. But it actually points to the virtual cpufreq-cpu0 platform device which is not present in the device tree. Most of the information needed by cpufreq is stored in cpu0 DT node. So cpu_dev must point to cpu0 device. This patch fixes the wrong assignment to cpu_dev. Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-09-18Merge tag 'omap-for-v3.12/fixes-dt-signed' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes From Tony Lindgren, OMAP DT fixes for 3.12-rc1: OMAP device tree changes that are needed to fix regressions and avoid electrical issues on beaglebone black. Via Benoit Cousson <bcousson@baylibre.com>: Fix BBB LDO voltage to avoid HDMI destruction Fix OMAP5 wrong attribute Fix typo in beagle xM strings Fix missing pinmux and regulator for OMAP4 wifi Fix missing pinmux for igep headset * tag 'omap-for-v3.12/fixes-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: igep00x0: Add pinmux configuration for MCBSP2 ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blaze ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboard ARM: dts: OMAP5: fix ocp2scp DTS data ARM: dts: OMAP5: fix reg property size ARM: dts: am335x-bone*: add DT for BeagleBone Black ARM: dts: omap3-beagle-xm: fix string error in compatible property Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-18Merge tag 'omap-for-v3.12/fixes-signed' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes From Tony Lindgren, fixes for 3.12-rc1: OMAP fixes for build warnings and cpuidle, and a few trivial typo fixes. * tag 'omap-for-v3.12/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP2+: mux: fix trivial typo in name ARM: OMAP4 SMP: Corrected a typo fucntions to functions ARM: OMAP4: cpuidle: fix: call cpu_cluster_pm_exit conditionally mailbox: remove unnecessary platform_set_drvdata() ARM: mach-omap2: gpmc: Fix warning when CONFIG_ARM_LPAE=y ARM: OMAP: fix return value check in omap_device_build_from_dt() ARM: OMAP4: Fix clock_get error for GPMC during boot Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-18ARM: multi_v7: add HREFv60 to multi_v7 defconfigLinus Walleij
This is just a standard board for the Ux500, include it in the v7 multiplatform defconfig. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-18ARM: OMAP2+: mux: fix trivial typo in namePhil Carmody
Fix trivial typo in name. Signed-off-by: Phil Carmody <phil.carmody@partner.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-09-18ARM: OMAP4 SMP: Corrected a typo fucntions to functionsAnoop Thomas Mathew
Corrected the functions spelling mistake in the OMAP4 SMP source file. Signed-off-by: Anoop Thomas Mathew <atm@profoundis.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-09-18ARM: OMAP4: cpuidle: fix: call cpu_cluster_pm_exit conditionallyVladimir Murzin
We call cpu_cluster_pm_enter for dev->cpu == 0 only, but cpu_cluster_pm_exit called without that check. Because of that unhandled page fault may happen: [ 3.803405] Unable to handle kernel paging request at virtual address 00002500 [ 3.810974] pgd = c0004000 [ 3.813812] [00002500] *pgd=00000000 [ 3.817596] Internal error: Oops: 5 [#1] SMP ARM [ 3.822418] Modules linked in: [ 3.825653] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.11.0-rc6+ #21 [ 3.832397] task: ed86ef40 ti: ed896000 task.ti: ed896000 [ 3.838073] PC is at irq_notifier+0x234/0x25c [ 3.842651] LR is at irq_notifier+0x218/0x25c [ 3.847229] pc : [<c0029ed8>] lr : [<c0029ebc>] psr: 80000193 [ 3.847229] sp : ed897ee8 ip : 00000005 fp : 00000001 [ 3.859283] r10: c0b395f0 r9 : c0b30594 r8 : c0b8c2ac [ 3.864776] r7 : ffffffff r6 : 00000000 r5 : 00000005 r4 : 00000000 [ 3.871643] r3 : 00002500 r2 : 00000000 r1 : 00000005 r0 : 44302244 [ 3.878479] Flags: Nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel [ 3.886260] Control: 10c5387d Table: 8000404a DAC: 00000015 [ 3.892272] Process swapper/1 (pid: 0, stack limit = 0xed896240) [ 3.898590] Stack: (0xed897ee8 to 0xed898000) [ 3.903167] 7ee0: c0979c3a 00000001 ed897ef8 ed896000 c0014f7c 00000000 [ 3.911743] 7f00: 00000005 00000000 ffffffff c0b8c2ac c0b395f0 c077c04c c0c94b48 c0b3953c [ 3.920318] 7f20: c0bcd928 00000002 c0b39524 c00cfad8 00000000 ffffffff 00000000 c00cfb10 [ 3.928924] 7f40: c14e62c0 c002c1c8 c002c0ac c14e62c0 00000002 e251c37d 00000000 c0b39548 [ 3.937499] 7f60: c0b395f0 c05a1bc4 e251c37d 00000000 00000005 c05a3870 edc90380 edc90380 [ 3.946105] 7f80: edc90394 c14e62c0 c0b39548 00000002 c0784064 c05a3c78 c0b395e0 c14e62c0 [ 3.954681] 7fa0: 00000002 c0b39548 c0bc9db8 00000000 00000001 c05a1dc0 ed896000 00000015 [ 3.963287] 7fc0: c0bc9db8 ed896000 8000406a c0b30594 c0784064 c000e504 00000746 c007a528 [ 3.971862] 7fe0: 00000001 0000001d 600001d3 c0bcc004 00000000 800086c4 ee0aa6a7 d2aabaa9 [ 3.980499] [<c0029ed8>] (irq_notifier+0x234/0x25c) from [<c077c04c>] (notifier_call_chain+0x38/0x68) [ 3.990173] [<c077c04c>] (notifier_call_chain+0x38/0x68) from [<c00cfad8>] (cpu_pm_notify+0x20/0x38) [ 3.999786] [<c00cfad8>] (cpu_pm_notify+0x20/0x38) from [<c00cfb10>] (cpu_cluster_pm_exit+0x20/0x50) [ 4.009399] [<c00cfb10>] (cpu_cluster_pm_exit+0x20/0x50) from [<c002c1c8>] (omap_enter_idle_coupled+0x11c/0x14c) [ 4.020111] [<c002c1c8>] (omap_enter_idle_coupled+0x11c/0x14c) from [<c05a1bc4>] (cpuidle_enter_state+0x40/0xec) [ 4.030822] [<c05a1bc4>] (cpuidle_enter_state+0x40/0xec) from [<c05a3c78>] (cpuidle_enter_state_coupled+0x1f4/0x240) [ 4.041870] [<c05a3c78>] (cpuidle_enter_state_coupled+0x1f4/0x240) from [<c05a1dc0>] (cpuidle_idle_call+0x150/0x228) [ 4.052947] [<c05a1dc0>] (cpuidle_idle_call+0x150/0x228) from [<c000e504>] (arch_cpu_idle+0x8/0x38) [ 4.062499] [<c000e504>] (arch_cpu_idle+0x8/0x38) from [<c007a528>] (cpu_startup_entry+0x178/0x1e4) [ 4.071990] [<c007a528>] (cpu_startup_entry+0x178/0x1e4) from [<800086c4>] (0x800086c4) [ 4.080383] Code: e5922288 03a03b0a 13a03c25 e0823003 (e5932000) [ 4.086791] ---[ end trace d83954a84a6fa69e ]--- It is supposed that sar_base is initialized in irq_save_context, which is called on CPU_CLUSTER_PM_ENTER notification. If this notification has been missed and CPU_CLUSTER_PM_EXIT is received sar_base is NULL. Fix it by calling CPU_CLUSTER_PM_{ENTER,EXIT} under the same condition. Signed-off-by: Vladimir Murzin <murzin.v@gmail.com> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-09-18ARM: mach-omap2: gpmc: Fix warning when CONFIG_ARM_LPAE=yFabio Estevam
When CONFIG_ARM_LPAE=y the following build warning is generated: arch/arm/mach-omap2/gpmc.c:1495:4: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat] According to Documentation/printk-formats.txt '%pa' can be used to properly print 'resource_size_t'. Reported-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-09-18ARM: OMAP: fix return value check in omap_device_build_from_dt()Wei Yongjun
In case of error, the function omap_device_alloc() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-09-18ARM: OMAP4: Fix clock_get error for GPMC during bootTony Lindgren
Looks like we still have the legacy clock alias name for omap4 GPMC (General Purpose Memory Controller), so let's fix it for the device tree naming. There's no need to keep the legacy naming as omap4 is DT only nowadays. Without this fix we get the following error while booting: [ 0.440399] omap-gpmc 50000000.gpmc: error: clk_get Reported-by: Olof Johansson <olof@lixom.net> Cc: stable@vger.kernel.org # v3.11 Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-09-18ARM: sa1100: collie.c: fall back to jedec_probe flash detectionAndrea Adami
Zaurus collie contains 2 LH28F640BFHE-PTTL90 (64M 4Mx16) and at the moment cfi will not detect the collie NOR. In the meanwhile we can revert to the jedec-probe map which has been fixed with following commit: mtd: jedec_probe: fix LH28F640BF definition fe2f4c8e0bf2756b670ee78fa9772613a2ea8495 Somehow this is unsatisfactory because the flash is mounted READ ONLY (as from factory, with a RO cramfs) Signed-off-by: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-18ARM: u300: hide submenusLinus Walleij
Right now the U300 submenus are showcased for everyone even if we're not on v5 multiplatforms. Hide this in the multiplatform configuration properly. Cc: arm@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-18ARM: dts: igep00x0: Add pinmux configuration for MCBSP2Enric Balletbo i Serra
Add pinmux configuration for MCBSP2 connected to the TDM interface. With this configuration the Headset modules works as expected. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-09-18ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blazeTony Lindgren
Commit 76787b3b (ARM: OMAP2+: Remove board-4430sdp.c) removed legacy booting in favor of device tree based booting for 4430sdp. That caused the WLAN to stop working as the related .dts entries fell through the cracks. I don't have the "1283 PG 2.21 connectivity device" on my 4430sdp, but the earlier version of this patch was tested by Luciano Coelho. This version has left out the input logic for MMC CLK line compared to the earlier version as that is not bidirectional, and should be safe to do. Cc: Rajendra Nayak <rnayak@ti.com> Cc: Luciano Coelho <luca@coelho.fi> Cc: Ruslan Bilovol <ruslan.bilovol@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-09-18ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboardTony Lindgren
Commit b42b9181 (ARM: OMAP2+: Remove board-omap4panda.c) removed legacy booting in favor of device tree based booting for pandaboard. That caused the WLAN to stop working as the related .dts entries fell through the cracks. The legacy muxing was setting pulls for GPIO 48 and 49, so let's keep that behaviour for now to avoid further regressions for BT and FM. Also input logic was enabled for MMC CLK line, but I've verified that the input logic we don't need enabled for CLK line as it's not bidirectional. Also, we want to use non-removable instead of ti,non-removable as the ti,non-removable also sets no_regulator_off_init which is really not what we want as then wl12xx won't get powered up and down which is needed for resetting it. Note that looks like the WLAN interface fails to come up after a warm reset, but that most likely was also happening with the legacy booting and needs a separate fix. Cc: Paolo Pisati <p.pisati@gmail.com> Cc: Rajendra Nayak <rnayak@ti.com> Cc: Luciano Coelho <luca@coelho.fi> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-09-17Merge tag 'imx-fixes-3.12' of git://git.linaro.org/people/shawnguo/linux-2.6 ↵Olof Johansson
into fixes From Shawn Guo, imx fixes for 3.12: * A couple of clock driver and device tree fixes * A bug fix for clk-fixup-mux to get imx6sl back to boot * A L2 cache setting fix for imx6q * One pinctrl macro fix for UART2 DTE entries * tag 'imx-fixes-3.12' of git://git.linaro.org/people/shawnguo/linux-2.6: ARM: dts: imx6q: fix the wrong offset of the Pad Mux register ARM: imx: i.mx6d/q: disable the double linefill feature of PL310 ARM: imx51.dtsi: fix PATA device clock ARM: mach-imx: clk-imx51-imx53: Fix 'spdif1_pred' clock registration ARM: imx: initialize clk_init_data.flags for clk-fixup-mux ARM: imx27.dtsi: fix CSPI PER clock id Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-17ARM: multi_v7_defconfig: enable ARM_ATAG_DTB_COMPATOlof Johansson
Without this, legacy platforms that can boot with a multiplatform kernel but that need the DTB to be appended, won't have a way to pass firmware-set bootargs to the kernel. This is needed to boot multi_v7_defconfig on snowball, for instance. Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-17ARM: ux500: disable outer cache debugLinus Walleij
This fixes a multiplatform regression on the Ux500. When compiling the Ux500 platforms in multiplatform configurations both PL310_ERRATA_588369 and PL310_ERRATA_727915 would crash the platform when trying to launch the init process. The Ux500 cannot access the debug registers of the PL310, it will just crash if you try this. So disable this by setting the debug callback to NULL when initializing the l2x0 on this platform. Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-17ARM: dts: OMAP5: fix ocp2scp DTS dataFelipe Balbi
Fix the DTS data for ocp2scp node by adding the missing reg property. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-09-17ARM: dts: OMAP5: fix reg property sizeFelipe Balbi
USB3 block has a 64KiB space, another 64KiB is used for the wrapper. Without this change, resource_size() will get confused and driver won't probe because size will be negative. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-09-17ARM: dts: am335x-bone*: add DT for BeagleBone BlackKoen Kooi
The BeagleBone Black is basically a regular BeagleBone with eMMC and HDMI added, so create a common dtsi both can use. IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI transceiver after a dozen boots with an uSD card inserted because LDO will be at 3.3V instead of 1.8. MMC support for AM335x still isn't in, so only the LDO change has been added. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Tested-by: Tom Rini <trini@ti.com> Tested-by: Matt Porter <matt.porter@linaro.org> Acked-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org> Tested-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-09-17ARM: dts: omap3-beagle-xm: fix string error in compatible propertyRobert Nelson
The beagle and beagle-xm entries were inside the same double quote. Split them to have two distinct entries. Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-09-17ARM: dts: imx6q: fix the wrong offset of the Pad Mux registerHuang Shijie
The patch "0b7a76a ARM: dts: imx6q{dl}: add DTE pads for uart" adds the DTE pads for uart. For PAD_EIM_D29, the offset of the Pad Mux register should be 0x0c8, not 0x0c4. This patch fixes it. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-09-17ARM: imx: i.mx6d/q: disable the double linefill feature of PL310Jason Liu
The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0 The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2 But according to ARM PL310 errata: 752271 ID: 752271: Double linefill feature can cause data corruption Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2 Workaround: The only workaround to this erratum is to disable the double linefill feature. This is the default behavior. without this patch, you will meet the following error when run the memtester application at: http://pyropus.ca/software/memtester/ FAILURE: 0x00100000 != 0x00200000 at offset 0x01365664. FAILURE: 0x00100000 != 0x00200000 at offset 0x01365668. FAILURE: 0x00100000 != 0x00200000 at offset 0x0136566c. FAILURE: 0x00100000 != 0x00200000 at offset 0x01365670. FAILURE: 0x00100000 != 0x00200000 at offset 0x01365674. FAILURE: 0x00100000 != 0x00200000 at offset 0x01365678. Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-09-17ARM: imx51.dtsi: fix PATA device clockArnaud Patard (Rtp)
Commit 718a350 (ARM: i.MX51: Add PATA support) adds pata support to the imx51.dtsi file and is using clock 161. The problem is that the right clock is 172, according to commit 5d530bb (ARM: i.MX5: Add PATA and SRTC clocks). Using the clock 172 makes things work again (and kills a nasty system freeze). Tested-by: Steev Klimaszewski <steev@gentoo.org> Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-09-17ARM: mach-imx: clk-imx51-imx53: Fix 'spdif1_pred' clock registrationFabio Estevam
Since commit beb2d1c1ba (ARM i.MX5: Add S/PDIF clocks), the following clock error appears on mx51: TrustZone Interrupt Controller (TZIC) initialized i.MX51 clk 180: register failed with -17 i.MX5 clk 180: register failed with -17 sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms CPU identified as i.MX51, silicon rev 3.0 ... Clock 180 corresponds to 'spdif1_podf' and this clock is getting registered twice. Fix it, by properly registering the 'spdif1_pred' clock, which should not reference 'spdif1_podf'. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-09-17ARM: imx: initialize clk_init_data.flags for clk-fixup-muxShawn Guo
The clk_init_data.flags of clk-fixup-mux is left there without initialization. It may hold some random data and cause clock framework interpret the clock in an unexpected way. At least on imx6sl, the following division by zero error with sched_clock is seen because of it. Division by zero in kernel. CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-rc3+ #19 Backtrace: [<80011af0>] (dump_backtrace+0x0/0x10c) from [<80011c90>] (show_stack+0x18/0x1c) r6:3b9aca00 r5:00000020 r4:00000000 r3:00000000 [<80011c78>] (show_stack+0x0/0x1c) from [<8055e02c>] (dump_stack+0x78/0x94) [<8055dfb4>] (dump_stack+0x0/0x94) from [<80011924>] (__div0+0x18/0x20) r4:00000000 r3:00000000 [<8001190c>] (__div0+0x0/0x20) from [<8026c408>] (Ldiv0_64+0x8/0x18) [<8006330c>] (clocks_calc_mult_shift+0x0/0xf8) from [<8072f604>] (setup_sched_clock+0x88/0x1f0) [<8072f57c>] (setup_sched_clock+0x0/0x1f0) from [<8071ad48>] (mxc_timer_init+0xe8/0x17c) [<8071ac60>] (mxc_timer_init+0x0/0x17c) from [<807290b0>] (imx6sl_clocks_init+0x1db8/0x1dc0) r8:807a9ca4 r7:00000000 r6:80777564 r5:8100c1f4 r4:c0820000 [<807272f8>] (imx6sl_clocks_init+0x0/0x1dc0) from [<807420ac>] (of_clk_init+0x40/0x6c) [<8074206c>] (of_clk_init+0x0/0x6c) from [<807290cc>] (imx6sl_timer_init+0x14/0x18) r5:807a8e80 r4:ffffffff [<807290b8>] (imx6sl_timer_init+0x0/0x18) from [<80716e1c>] (time_init+0x24/0x34) [<80716df8>] (time_init+0x0/0x34) from [<80713738>] (start_kernel+0x1b0/0x310) [<80713588>] (start_kernel+0x0/0x310) from [<80008074>] (0x80008074) r7:80770b08 r6:80754cd4 r5:8076c8c4 r4:10c53c7d sched_clock: 32 bits at 0 Hz, resolution 0ns, wraps every 0ms Fix the bug by initializing init.flags as zero. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-09-17ARM: imx27.dtsi: fix CSPI PER clock idGwenhael Goavec-Merou
CSPI PER clock is per2clk (per2_gate id 60) instead of cspiX_ipg_gate. Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-09-16Merge branch 'timers/core' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer code update from Thomas Gleixner: - armada SoC clocksource overhaul with a trivial merge conflict - Minor improvements to various SoC clocksource drivers * 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding clocksource: armada-370-xp: Get reference fixed-clock by name clocksource: armada-370-xp: Replace WARN_ON with BUG_ON clocksource: armada-370-xp: Fix device-tree binding clocksource: armada-370-xp: Introduce new compatibles clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE clocksource: armada-370-xp: Simplify TIMER_CTRL register access clocksource: armada-370-xp: Use BIT() ARM: timer-sp: Set dynamic irq affinity ARM: nomadik: add dynamic irq flag to the timer clocksource: sh_cmt: 32-bit control register support clocksource: em_sti: Convert to devm_* managed helpers
2013-09-13Remove GENERIC_HARDIRQ config optionMartin Schwidefsky
After the last architecture switched to generic hard irqs the config options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code for !CONFIG_GENERIC_HARDIRQS can be removed. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2013-09-12Merge branch 'akpm' (patches from Andrew Morton)Linus Torvalds
Merge more patches from Andrew Morton: "The rest of MM. Plus one misc cleanup" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (35 commits) mm/Kconfig: add MMU dependency for MIGRATION. kernel: replace strict_strto*() with kstrto*() mm, thp: count thp_fault_fallback anytime thp fault fails thp: consolidate code between handle_mm_fault() and do_huge_pmd_anonymous_page() thp: do_huge_pmd_anonymous_page() cleanup thp: move maybe_pmd_mkwrite() out of mk_huge_pmd() mm: cleanup add_to_page_cache_locked() thp: account anon transparent huge pages into NR_ANON_PAGES truncate: drop 'oldsize' truncate_pagecache() parameter mm: make lru_add_drain_all() selective memcg: document cgroup dirty/writeback memory statistics memcg: add per cgroup writeback pages accounting memcg: check for proper lock held in mem_cgroup_update_page_stat memcg: remove MEMCG_NR_FILE_MAPPED memcg: reduce function dereference memcg: avoid overflow caused by PAGE_ALIGN memcg: rename RESOURCE_MAX to RES_COUNTER_MAX memcg: correct RESOURCE_MAX to ULLONG_MAX mm: memcg: do not trap chargers with full callstack on OOM mm: memcg: rework and document OOM waiting and wakeup ...
2013-09-12arch: mm: pass userspace fault flag to generic fault handlerJohannes Weiner
Unlike global OOM handling, memory cgroup code will invoke the OOM killer in any OOM situation because it has no way of telling faults occuring in kernel context - which could be handled more gracefully - from user-triggered faults. Pass a flag that identifies faults originating in user space from the architecture-specific fault handlers to generic code so that memcg OOM handling can be improved. Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Michal Hocko <mhocko@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: azurIt <azurit@pobox.sk> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-09-12arch: mm: do not invoke OOM killer on kernel fault OOMJohannes Weiner
Kernel faults are expected to handle OOM conditions gracefully (gup, uaccess etc.), so they should never invoke the OOM killer. Reserve this for faults triggered in user context when it is the only option. Most architectures already do this, fix up the remaining few. Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Michal Hocko <mhocko@suse.cz> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: azurIt <azurit@pobox.sk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-09-12Merge tag 'fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "A small batch of fixes that have trickled in over the last week of the merge window. Also included are few small devicetree updates for sunxi, since it enables me to use one of their newer boards (cubieboard2) for additional test coverage. The support for that SoC is new for 3.12, so there's no exposure to new regressions due to it" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: dts: sun7i: olinuxino-micro: Enable the EMAC ARM: dts: sun7i: cubieboard2: Enable the EMAC ARM: dts: sun7i: Add the muxing options for the EMAC ARM: dts: sun7i: Enable the Ethernet in the A20 i2c: davinci: Fix bad dev_get_platdata() conversion ARM: vexpress: allow dcscb and tc2_pm in a combined ARMv6+v7 build ARM: shmobile: lager: Do not use register_type field of struct sh_eth_plat_data ARM: pxa: ssp: Check return values from phandle lookups ARM: PCI: versatile: Fix SMAP register offsets ARM: PCI: versatile: Fix PCI I/O ARM: PCI: versatile: Fix map_irq function to match hardware ARM: ep93xx: Don't use modem interface on the second UART ARM: shmobile: r8a7779: Update early timer initialisation order
2013-09-12Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: "Just two fixes here - one for the recent addition of Neon stuff which causes problems when this is built as a module. The other was one spotted by Olof with the fixed-HZ stuff. Last patch (which is at the very top) is not a fix per-se, but an almost-end-of-merge window sorting of the select symbols in arch/arm/Kconfig to keep them as akpm would like to reduce unnecessary conflicts. I've also taken the liberty this time to add a comment at the end to discourage the endless "add the next select to the bottom of a nicely sorted list" syndrome" * 'fixes' of git://git.linaro.org/people/rmk/linux-arm: ARM: sort arch/arm/Kconfig ARM: fix forced-HZ values ARM: 7835/2: fix modular build of xor_blocks() with NEON enabled
2013-09-12ARM: sort arch/arm/KconfigRussell King
Keep arch/arm/Kconfig select statements sorted alphabetically. I've added a comment at the bottom of the main bank for CONFIG_ARM to this effect so hopefully this will keep things more in order. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-09-12ARM: dts: sun7i: olinuxino-micro: Enable the EMACMaxime Ripard
The A20-olinuxino-micro has the EMAC wired in. Enable it in the DT so that we can use it. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-12ARM: dts: sun7i: cubieboard2: Enable the EMACMaxime Ripard
The Cubieboard2, just like its A10 counterpart, has the Ethernet wired in. Enable it in the DT. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-12ARM: dts: sun7i: Add the muxing options for the EMACMaxime Ripard
The A20 has several muxing options for the EMAC. Yet, the currently supported boards only use one set of them. Add that pin set to the DTSI. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-12ARM: dts: sun7i: Enable the Ethernet in the A20Maxime Ripard
The Allwinner A20 SoC also have the EMAC found on the A10 and A10s. Enable the support for it in the DTSI. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-11mm: migrate: check movability of hugepage in unmap_and_move_huge_page()Naoya Horiguchi
Currently hugepage migration works well only for pmd-based hugepages (mainly due to lack of testing,) so we had better not enable migration of other levels of hugepages until we are ready for it. Some users of hugepage migration (mbind, move_pages, and migrate_pages) do page table walk and check pud/pmd_huge() there, so they are safe. But the other users (softoffline and memory hotremove) don't do this, so without this patch they can try to migrate unexpected types of hugepages. To prevent this, we introduce hugepage_migration_support() as an architecture dependent check of whether hugepage are implemented on a pmd basis or not. And on some architecture multiple sizes of hugepages are available, so hugepage_migration_support() also checks hugepage size. Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Hillf Danton <dhillf@gmail.com> Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Rik van Riel <riel@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-09-10Merge tag 'stable/for-linus-3.12-rc0-tag-two' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull Xen bug-fixes from Konrad Rzeszutek Wilk: "This pull I usually do after rc1 is out but because we have a nice amount of fixes, some bootup related fixes for ARM, and it is early in the cycle we figured to do it now to help with tracking of potential regressions. The simple ones are the ARM ones - one of the patches fell through the cracks, other fixes a bootup issue (unconditionally using Xen functions). Then a fix for a regression causing preempt count being off (patch causing this went in v3.12). Lastly are the fixes to make Xen PVHVM guests use PV ticketlocks (Xen PV already does). The enablement of that was supposed to be part of the x86 spinlock merge in commit 816434ec4a67 ("The biggest change here are paravirtualized ticket spinlocks (PV spinlocks), which bring a nice speedup on various benchmarks...") but unfortunatly it would cause hang when booting Xen PVHVM guests. Yours truly got all of the bugs fixed last week and they (six of them) are included in this pull. Bug-fixes: - Boot on ARM without using Xen unconditionally - On Xen ARM don't run cpuidle/cpufreq - Fix regression in balloon driver, preempt count warnings - Fixes to make PVHVM able to use pv ticketlock. - Revert Xen PVHVM disabling pv ticketlock (aka, re-enable pv ticketlocks)" * tag 'stable/for-linus-3.12-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/spinlock: Don't use __initdate for xen_pv_spin Revert "xen/spinlock: Disable IRQ spinlock (PV) allocation on PVHVM" xen/spinlock: Don't setup xen spinlock IPI kicker if disabled. xen/smp: Update pv_lock_ops functions before alternative code starts under PVHVM xen/spinlock: We don't need the old structure anymore xen/spinlock: Fix locking path engaging too soon under PVHVM. xen/arm: disable cpuidle and cpufreq when linux is running as dom0 xen/p2m: Don't call get_balloon_scratch_page() twice, keep interrupts disabled for multicalls ARM: xen: only set pm function ptrs for Xen guests
2013-09-10Merge tag 'ep93xx-fixes-for-3.12' of ↵Olof Johansson
git://github.com/RyanMallon/linux-ep93xx into fixes From Ryan Mallon, a fix for ep93xx. * tag 'ep93xx-fixes-for-3.12' of git://github.com/RyanMallon/linux-ep93xx: ARM: ep93xx: Don't use modem interface on the second UART Signed-off-by: Olof Johansson <olof@lixom.net>
2013-09-10ARM: fix forced-HZ valuesRussell King
Olof Johansson reports that the tests against HZ_FIXED seem non-functional. Fix this by using '0' as a sentinel for "not specified" and test against that instead. Reported-by: Olof Johansson <olof@lixom.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-09-10Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linuxLinus Torvalds
Pull device tree core updates from Grant Likely: "Generally minor changes. A bunch of bug fixes, particularly for initialization and some refactoring. Most notable change if feeding the entire flattened tree into the random pool at boot. May not be significant, but shouldn't hurt either" Tim Bird questions whether the boot time cost of the random feeding may be noticeable. And "add_device_randomness()" is definitely not some speed deamon of a function. * tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: of/platform: add error reporting to of_amba_device_create() irq/of: Fix comment typo for irq_of_parse_and_map of: Feed entire flattened device tree into the random pool of/fdt: Clean up casting in unflattening path of/fdt: Remove duplicate memory clearing on FDT unflattening gpio: implement gpio-ranges binding document fix of: call __of_parse_phandle_with_args from of_parse_phandle of: introduce of_parse_phandle_with_fixed_args of: move of_parse_phandle() of: move documentation of of_parse_phandle_with_args of: Fix missing memory initialization on FDT unflattening of: consolidate definition of early_init_dt_alloc_memory_arch() of: Make of_get_phy_mode() return int i.s.o. const int include: dt-binding: input: create a DT header defining key codes. of/platform: Staticize of_platform_device_create_pdata() of: Specify initrd location using 64-bit dt: Typo fix OF: make of_property_for_each_{u32|string}() use parameters if OF is not enabled