aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-07-24i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converterEmmanuel Deloget
Robofuzz OSIF is a generic USB/iIC interface that embeds an ATMega8A AVR-RISC microcontroler. The device is based upon Till Harbaum's i2c-tiny-usb and although it enhances the original design with further functionnalities it still maintain compatibility with it with respect to the USB/I2C interface. Signed-off-by: Emmanuel Deloget <logout@free.fr> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-i801: Enable IRQ for byte_by_byte transactionsDaniel Kurtz
Byte-by-byte transactions are used primarily for accessing I2C devices with an SMBus controller. For these transactions, for each byte that is read or written, the SMBus controller generates a BYTE_DONE IRQ. The isr reads/writes the next byte, and clears the IRQ flag to start the next byte. On the penultimate IRQ, the isr also sets the LAST_BYTE flag. There is no locking around the cmd/len/count/data variables, since the I2C adapter lock ensures there is never multiple simultaneous transactions for the same device, and the driver thread never accesses these variables while interrupts might be occurring. The end result is faster I2C block read and write transactions. Note: This patch has only been tested and verified by doing I2C read and write block transfers on Cougar Point 6 Series PCH, as well as I2C read block transfers on ICH5. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-i801: Enable interrupts on ICH5/7/8/9/10Jean Delvare
Enable interrupts on more devices. ICH5, ICH7(-M) and ICH10 have been tested to work OK. ICH8 and ICH9 are expected to work just fine as they are very close to ICH7 and ICH10. Ultimately we want to enable this feature on at least every device since the ICH5, but for now we limit the exposure. We'll enable it for other devices if we don't get negative feedback. As a bonus, let the user know when interrupts are used. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Daniel Kurtz <djkurtz@chromium.org>
2012-07-24i2c-i801: Enable IRQ for SMBus transactionsDaniel Kurtz
Add a new 'feature' to i2c-i801 to enable using PCI interrupts. When the feature is enabled, then an isr is installed for the device's PCI IRQ. An I2C/SMBus transaction is always terminated by one of the following interrupt sources: FAILED, BUS_ERR, DEV_ERR, or on success: INTR. When the isr fires for one of these cases, it sets the ->status variable and wakes up the waitq. The waitq then saves off the status code, and clears ->status (in preparation for some future transaction). The SMBus controller generates an INTR irq at the end of each transaction where INTREN was set in the HST_CNT register. No locking is needed around accesses to priv->status since all writes to it are serialized: it is only ever set once in the isr at the end of a transaction, and cleared while no interrupts can occur. In addition, the I2C adapter lock guarantees that entire I2C transactions for a single adapter are always serialized. For this patch, the INTREN bit is set only for SMBus block, byte and word transactions, but not for I2C reads or writes. The use of the DS (BYTE_DONE) interrupt with byte-by-byte I2C transactions is implemented in a subsequent patch. The interrupt feature has only been enabled for COUGARPOINT hardware. In addition, it is disabled if SMBus is using the SMI# interrupt. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-i801: Consolidate pollingJean Delvare
(Based on earlier work by Daniel Kurtz.) Come up with a consistent, driver-wide strategy for event polling. For intermediate steps of byte-by-byte block transactions, check for BYTE_DONE or any error flag being set. At the end of every transaction (regardless of PEC being used), check for both BUSY being cleared and INTR or any error flag being set. This ensures proper action for all transaction types. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Daniel Kurtz <djkurtz@chromium.org>
2012-07-24i2c-i801: Drop ENABLE_INT9Daniel Kurtz
Later patches enable interrupts. This preliminary patch removes the older unsupported ENABLE_INT9 flag. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-i801: Rename some SMBHSTCNT bit constantsDaniel Kurtz
Rename the SMBHSTCNT register bit access constants to match the style of other register bits. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-i801: Check and return errors during byte-by-byte transfersDaniel Kurtz
If an error is detected in the polling loop, abort the transaction and return an error code. * DEV_ERR is set if the device does not respond with an acknowledge, and the SMBus controller times out (minimum 25ms). * BUS_ERR is set if a bus arbitration collision is detected. In other words, when the SMBus controller tries to generate a START condition, but detects that the SMBDATA is being held low, usually by another SMBus/I2C master. * FAILED is only set if a transaction is stopped by software (using the SMBHSTCNT KILL bit). Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-i801: Clear only status bits in HST_STSDaniel Kurtz
Writing back the whole status register could clear unwanted bits. In particular, it could clear the "INUSE_STS" bit, which is a 'hardware semaphore', that might be useful to use some day. To prepare for this, let's ban writing back the whole status to register HST_STS, of which this is the only instance. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-i801: Refactor use of LAST_BYTE in i801_block_transaction_byte_by_byteDaniel Kurtz
As a slight optimization, pull some logic out of the polling loop during byte-by-byte transactions by just setting the I801_LAST_BYTE bit, as defined in the i801 (PCH) datasheet, when reading the last byte of a byte-by-byte I2C_SMBUS_READ. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-smbus: Use module_i2c_driver()Fabio Estevam
Using module_i2c_driver() makes the code smaller and cleaner. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c/writing-clients: Mention module_i2c_driver()Jean Delvare
Based on a previous patch from Peter Meerwald. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-07-24i2c-piix4: Support AMD auxiliary SMBus controllerAndrew Armenia
Some AMD chipsets, such as the SP5100, have an auxiliary SMBus controller with a second set of registers. This patch adds support for this auxiliary controller. Tested on ASUS KCMA-D8 motherboard. Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-piix4: Separate registration and probing codeAndrew Armenia
Some chipsets have multiple sets of SMBus registers each controlling a separate SMBus. Supporting these chipsets properly will require registering multiple I2C adapters for one piix4. The code to initialize and register the i2c_adapter structure has been separated from piix4_probe and allows registration of a piix4 adapter given its base address. Note that the i2c_adapter and i2c_piix4_adapdata structures are now dynamically allocated. Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c-piix4: Eliminate piix4_smba global variableAndrew Armenia
Some chipsets have multiple sets of piix4-compatible SMBus registers. Eliminating the global variable will allow these chipsets to be fully supported. Return value from piix4_setup and piix4_sb800_setup now returns the smba value detected. This is stored in a struct i2c_piix4_adapdata. Thus the global variable is eliminated. Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24i2c/busses: Use module_pci_driverAxel Lin
Convert the drivers in drivers/i2c/busses/* to usemodule_pci_driver() macro which makes the code smaller and a bit simpler. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Rudolf Marek <r.marek@assembler.cz> Cc: Olof Johansson <olof@lixom.net> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>
2012-07-24i2c: Update Guenter Roeck's e-mail addressGuenter Roeck
My old e-mail address won't be valid for much longer. Time to update it. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tileLinus Torvalds
Pull arch/tile updates from Chris Metcalf: "These changes provide support for PCIe root complex and USB host mode for tilegx's on-chip I/Os. In addition, this pull provides the required underpinning for the on-chip networking support that was pulled into 3.5. The changes have all been through LKML (with several rounds for PCIe RC) and on linux-next." * git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: tile: updates to pci root complex from community feedback bounce: allow use of bounce pool via config option usb: add host support for the tilegx architecture arch/tile: provide kernel support for the tilegx USB shim tile pci: enable IOMMU to support DMA for legacy devices arch/tile: enable ZONE_DMA for tilegx tilegx pci: support I/O to arbitrarily-cached pages tile: remove unused header arch/tile: tilegx PCI root complex support arch/tile: provide kernel support for the tilegx TRIO shim arch/tile: break out the "csum a long" function to <asm/checksum.h> arch/tile: provide kernel support for the tilegx mPIPE shim arch/tile: common DMA code for the GXIO IORPC subsystem arch/tile: support MMIO-based readb/writeb etc. arch/tile: introduce GXIO IORPC framework for tilegx
2012-07-23Merge tag 'please-pull-misc-3.6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux Pull misc Itanium fixes from Tony Luck. * tag 'please-pull-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: debug: Do not permit CONFIG_DEBUG_STACK_USAGE=y on IA64 or PARISC [IA64] Port OOM changes to ia64_do_page_fault
2012-07-23Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-shLinus Torvalds
Pull SuperH updates from Paul Mundt: - Migration off of old-style dynamic IRQ API. - irqdomain and generic irq chip propagation. - div4/6 clock consolidation, another step towards co-existing with the common struct clk infrastructure. - Extensive PFC rework - Decoupling GPIO from pin state. - Initial pinctrl support to facilitate incremental migration off of legacy pinmux. - gpiolib support made optional, and made pinctrl-backed. * tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (38 commits) sh: pfc: pin config get/set support. sh: pfc: Prefer DRV_NAME over KBUILD_MODNAME. sh: pfc: pinctrl legacy group support. sh: pfc: Ignore pinmux GPIOs with invalid enum IDs. sh: pfc: Export pinctrl binding init symbol. sh: pfc: Error out on pinctrl init resolution failure. sh: pfc: Make pr_fmt consistent across pfc drivers. sh: pfc: pinctrl legacy function support. sh: pfc: Rudimentary pinctrl-backed GPIO support. sh: pfc: Dumb GPIO stringification. sh: pfc: Shuffle PFC support core. sh: pfc: Verify pin type encoding size at build time. sh: pfc: Kill off unused pinmux bias flags. sh: pfc: Make gpio chip support optional where possible. sh: pfc: Split out gpio chip support. sh64: Fix up section mismatch warnings. sh64: Attempt to make reserved insn trap handler resemble C. sh: Consolidate die definitions for trap handlers. sh64: Kill off old exception debugging helpers. sh64: Use generic unaligned access control/counters. ...
2012-07-23Merge branch 'next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc Pull powerpc updates from Benjamin Herrenschmidt: "Notable highlights: - iommu improvements from Anton removing the per-iommu global lock in favor of dividing the DMA space into pools, each with its own lock, and hashed on the CPU number. Along with making the locking more fine grained, this gives significant improvements in multiqueue networking scalability. - Still from Anton, we know provide a vdso based variant of getcpu which makes sched_getcpu with the appropriate glibc patch something like 18 times faster. - More anton goodness (he's been busy !) in other areas such as a faster __clear_user and copy_page on P7, various perf fixes to improve sampling quality, etc... - One more step toward removing legacy i2c interfaces by using new device-tree based probing of platform devices for the AOA audio drivers - A nice series of patches from Michael Neuling that helps avoiding confusion between register numbers and litterals in assembly code, trying to enforce the use of "%rN" register names in gas rather than plain numbers. - A pile of FSL updates - The usual bunch of small fixes, cleanups etc... You may spot a change to drivers/char/mem. The patch got no comment or ack from outside, it's a trivial patch to allow the architecture to skip creating /dev/port, which we use to disable it on ppc64 that don't have a legacy brige. On those, IO ports 0...64K are not mapped in kernel space at all, so accesses to /dev/port cause oopses (and yes, distros -still- ship userspace that bangs hard coded ports such as kbdrate)." * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits) powerpc/mpic: Create a revmap with enough entries for IPIs and timers Remove stale .rej file powerpc/iommu: Fix iommu pool initialization powerpc/eeh: Check handle_eeh_events() return value powerpc/85xx: Add phy nodes in SGMII mode for MPC8536/44/72DS & P2020DS powerpc/e500: add paravirt QEMU platform powerpc/mpc85xx_ds: convert to unified PCI init powerpc/fsl-pci: get PCI init out of board files powerpc/85xx: Update corenet64_smp_defconfig powerpc/85xx: Update corenet32_smp_defconfig powerpc/85xx: Rename P1021RDB-PC device trees to be consistent powerpc/watchdog: move booke watchdog param related code to setup-common.c sound/aoa: Adapt to new i2c probing scheme i2c/powermac: Improve detection of devices from device-tree powerpc: Disable /dev/port interface on systems without an ISA bridge of: Improve prom_update_property() function powerpc: Add "memory" attribute for mfmsr() powerpc/ftrace: Fix assembly trampoline register usage powerpc/hw_breakpoints: Fix incorrect pointer access powerpc: Put the gpr save/restore functions in their own section ...
2012-07-23Merge branch 'next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security Pull security subsystem updates from James Morris: "Nothing groundbreaking for this kernel, just cleanups and fixes, and a couple of Smack enhancements." * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (21 commits) Smack: Maintainer Record Smack: don't show empty rules when /smack/load or /smack/load2 is read Smack: user access check bounds Smack: onlycap limits on CAP_MAC_ADMIN Smack: fix smack_new_inode bogosities ima: audit is compiled only when enabled ima: ima_initialized is set only if successful ima: add policy for pseudo fs ima: remove unused cleanup functions ima: free securityfs violations file ima: use full pathnames in measurement list security: Fix nommu build. samples: seccomp: add .gitignore for untracked executables tpm: check the chip reference before using it TPM: fix memleak when register hardware fails TPM: chip disabled state erronously being reported as error MAINTAINERS: TPM maintainers' contacts update Merge branches 'next-queue' and 'next' into next Remove unused code from MPI library Revert "crypto: GnuPG based MPI lib - additional sources (part 4)" ...
2012-07-23Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm-soc clk changes from Arnd Bergmann: "Clock support is moving to the clk subsystem. These tegra, omap and imx changes are for code that is still platform specific and not (yet) part of that subsystem." Fix up conflicts in arch/arm/mach-{imx/clk-imx51-imx53.c,omap2/Makefile} * tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits) ARM: imx: clk-imx31: Fix clock id for rnga driver ARM: imx: add missing item to the list of clock event modes ARM: i.MX5x CSPI: Fixed clock name for CSPI ARM: i.MX5x clocks: Fix GPT clocks ARM: i.MX5x clocks: Fix parent for PWM clocks ARM: i.MX5x clocks: Add EPIT support ARM: mx27: Reenable silicon version print ARM: clk-imx27: Fix rtc clock id ARM: tegra: Provide clock for only one PWM controller ARM: tegra: Fix PWM clock programming ARM: OMAP3+: clock33xx: Add AM33XX clock tree data ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file ARM: tegra: dma: rename driver name for clock to "tegra-apbdma" ARM: tegra: Remove second instance of uart clk crypto: add clk_prepare/clk_unprepare ASoC: tegra: add clk_prepare/clk_unprepare staging: nvec: add clk_prepare/clk_unprepare spi/tegra: add clk_prepare/clk_unprepare Input: tegra-kbc - add clk_prepare/clk_unprepare USB: ehci-tegra: add clk_prepare/clk_unprepare ...
2012-07-23Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm-soc power management changes from Arnd Bergmann: "These are various power management related changes, mainly concerning cpuidle on i.MX and OMAP, as well as a the move of the omap smartreflex driver to live in the power subsystem." Fix up conflicts in arch/arm/mach-{imx/mach-imx6q.c,omap2/prm2xxx_3xxx.h} * tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits) ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge ARM: OMAP2+: do not allow SmartReflex to be built as a module ARM: OMAP2: Use hwmod to initialize mmc for 2420 ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state ARM: OMAP3: PM: cleanup cam_pwrdm leftovers ARM: OMAP3: PM: call pre/post transition per powerdomain ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux ARM: OMAP3+: PRM: Enable IO wake up ARM: OMAP4: PRM: Add IO Daisychain support ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file ARM: OMAP3: PM: correct enable/disable of daisy io chain ARM: OMAP2+: PRM: fix compile for OMAP4-only build W1: OMAP HDQ1W: use runtime PM ARM: OMAP2+: HDQ1W: use omap_device W1: OMAP HDQ1W: use 32-bit register accesses W1: OMAP HDQ1W: allow driver to be built on all OMAP2+ ...
2012-07-23Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm-soc pincontrol drivers update from Arnd Bergmann: "We are converting platforms to use the pinctrl framework over time, rather than using platform specific code for the same effect. This adds the respective driver for the prima2 platform." * tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: prima2: enable gpiolib unconditionally PINCTRL: SiRF: add GPIO and GPIO irq support in CSR SiRFprimaII
2012-07-23Merge tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm-soc sparse IRQ conversion from Arnd Bergmann: "The I.MX platform is getting converted to use sparse IRQs. We are doing this for all platforms over time, because this is one of the requirements for building a multiplatform kernel, and generally a good idea." * tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: imx: select USE_OF ARM: imx: Fix build error due to missing irqs.h include ARM: imx: enable SPARSE_IRQ for imx platform ARM: fiq: change FIQ_START to a variable tty: serial: imx: remove the use of MXC_INTERNAL_IRQS ARM: imx: remove unneeded mach/irq.h inclusion i2c: imx: remove unneeded mach/irqs.h inclusion ARM: imx: add a legacy irqdomain for mx31ads ARM: imx: add a legacy irqdomain for 3ds_debugboard ARM: imx: pass gpio than irq number into mxc_expio_init ARM: imx: leave irq_base of wm8350_platform_data uninitialized dma: ipu: remove the use of ipu_platform_data ARM: imx: move irq_domain_add_legacy call into avic driver ARM: imx: move irq_domain_add_legacy call into tzic driver gpio/mxc: move irq_domain_add_legacy call into gpio driver ARM: imx: eliminate macro IRQ_GPIOx() ARM: imx: eliminate macro IOMUX_TO_IRQ() ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
2012-07-23Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm-soc board specific updates from Arnd Bergmann: "These changes are all for individual board files. In the long run, those files will largely go away, and the amount of changes appears to be continuously decreasing, which is a good sign. This time around, changes are focused on tegra, omap and samsung." Fix conflicts in arch/arm/mach-{omap2/common-board-devices.c,tegra/Makefile.boot} as per the 'for-linus' branch. * tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits) ARM: EXYNOS: Add leds status1 and status2 on Origen board ARM: S3C64XX: Mark most Cragganmore initdata devinitdata ARM: EXYNOS: Add missing .reserve field to SMDKC210 ARM: EXYNOS: Add DRM device to SMDK4X12 board ARM: S3C64XX: Clean up after SPI driver platform data updates ARM: SAMSUNG: no need to set the value for clk_xusbxti when it is 24Mhz ARM: EXYNOS: Add framebuffer support for SMDK4X12 ARM: EXYNOS: Add HSOTG support to SMDK4X12 ARM: S5PV210: Add audio platform device in Goni board ARM: S5PV210: Add audio platform device in Aquila board ARM: EXYNOS: Add audio platform device in SMDKV310 board ARM: S3C64XX: Don't specify an irq_base for WM1192-EV1 board ARM: OMAP3: Fix omap3evm randconfig error introduced by VBUS support ARM: OMAP: board-omap4panda: MUX configuration for sys_nirq2 ARM: OMAP: board-4430sdp: MUX configuration for sys_nirq2 ARM: OMAP3530evm: set pendown_state and debounce time for ads7846 ARM: omap3evm: enable VBUS switch for EHCI tranceiver ARM: OMAP3EVM: Adding USB internal LDOs board file ARM: OMAP3EVM: Add NAND flash definition ARM: OMAP3: cm-t35: add tvp5150 decoder support ...
2012-07-23Merge tag 'defconfig' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull arm-soc defconfig updates from Arnd Bergmann: "These are changes to the default configuration files, to account for kernel changes and new hardware." * tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: exynos_defconfig: enable more platforms in defconfig ARM: imx_v4_v5_defconfig: update features ARM: imx_v6_v7_defconfig: update features ARM: mxs: defconfig: Enable CONFIG_COMMON_CLK_DEBUG ARM: mxs_defconfig: Enable RTC driver ARM: LPC32xx: Defconfig update ARM: mxs_defconfig: Let AUART driver be built by default ARM: mxs: Enable MACH_APX4DEVKIT ARM: mxs: Let GPMI driver be built by default ARM: tegra: defconfig updates
2012-07-23Merge tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull support for three new arm SoC types from Arnd Bergmann: - The mvebu platform includes Marvell's Armada XP and Armada 370 chips, made by the mvebu business unit inside of Marvell. Since the same group also made the older but similar platforms we call "orion5x", "kirkwood", "mv78xx0" and "dove", we plan to move all of them into the mach-mvebu directory in the future. - socfpga is Altera's platform based on Cortex-A9 cores and a lot of FPGA space. This is similar to the Xilinx zynq platform we already support. The code is particularly clean, which is helped by the fact that the hardware doesn't do much besides the parts that are expected to get added in the FPGA. - The OMAP subarchitecture gains support for the latest generation, the OMAP5 based on the new Cortex-A15 core. Support is rather rudimentary for now, but will be extended in the future. * tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits) ARM: socfpga: initial support for Altera's SOCFPGA platform arm: mvebu: generate DTBs for supported SoCs ARM: mvebu: MPIC: read number of interrupts from control register arm: mach-mvebu: add entry to MAINTAINERS arm: mach-mvebu: add compilation/configuration change arm: mach-mvebu: add defconfig arm: mach-mvebu: add documentation for new device tree bindings arm: mach-mvebu: add support for Armada 370 and Armada XP with DT arm: mach-mvebu: add source files arm: mach-mvebu: add header clocksource: time-armada-370-xp: Marvell Armada 370/XP SoC timer driver ARM: Kconfig update to support additional GPIOs in OMAP5 ARM: OMAP5: Add the build support arm/dts: OMAP5: Add omap5 dts files ARM: OMAP5: board-generic: Add device tree support ARM: omap2+: board-generic: clean up the irq data from board file ARM: OMAP5: Add SMP support ARM: OMAP5: Add the WakeupGen IP updates ARM: OMAP5: l3: Add l3 error handler support for omap5 ARM: OMAP5: gpmc: Update gpmc_init() ... Conflicts: Documentation/devicetree/bindings/arm/omap/omap.txt arch/arm/mach-omap2/Makefile drivers/clocksource/Kconfig drivers/clocksource/Makefile
2012-07-23Merge tag 'cleanup2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull arm-soc cleanups, part 2, from Arnd Bergmann: "These omap cleanups have dependencies on earlier omap branches that in turn depend on other cleanups, so they could not go into the same branch." * tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: OMAP: sdrc: Fix the build break for OMAP4 only builds ARM: OMAP2+: dmtimer: cleanup fclk usage ARM: OMAP2+: Fix mismerge for omap_hwmod_get_main_clk() API ARM: OMAP2+: Remove unnecessary ifdef around __omap2_set_globals ARM: OMAP2+: am33xx: Change cpu_is_am33xx to soc_is_am33xx ARM: OMAP2+: am33xx: Make am33xx as a separate class ARM: OMAP2+: Move omap3 dpll ops to dpll3xxx.c ARM: OMAP2+: All OMAP2PLUS uses omap-device.o target so add one entry ARM: OMAP: dmtimer: use devm_ API and do some cleanup in probe() ARM: OMAP2+: hwmod code: add support to set dmadisable in hwmod framework ARM: OMAP2+: PRM/CM: Move the stubbed prm and cm functions to prcm.c file and make them __weak ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API ARM: OMAP3+: dpll: optimize noncore dpll locking logic ARM: OMAP3: control: add definition for CONTROL_CAMERA_PHY_CTRL ARM: OMAP2+: powerdomain code: Fix Wake-up power domain power status ARM: OMAP4: clockdomain/CM code: Update supported transition modes ARM: OMAP3/4: omap_hwmod: Add rstst_offs field to struct omap_hwmod_omap4_prcm ARM: OMAP2+: hwmod: Add new sysc_type3 into omap_hwmod required for am33xx
2012-07-23Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm-soc timer updates from Arnd Bergmann: "This contains two branches dealing with timers, one for the picoxcell platform that is now using DT with the platform-independent dw_apb_timer driver. The other change is for the omap-specific dmtimer driver." * tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer ARM: OMAP2+: Simplify dmtimer clock aliases ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver ARM: OMAP1: Fix dmtimer support ARM: OMAP: Add flag to indicate if a timer needs a manual reset ARM: OMAP: Remove timer function pointer for context loss counter ARM: OMAP: Remove loses_context variable from timer platform data ARM: OMAP2+: Fix external clock support for dmtimers ARM: OMAP2+: HWMOD: Correct timer device attributes ARM: OMAP: Add DMTIMER capability variable to represent timer features ARM: OMAP2+: Add dmtimer platform function to reserve systimers ARM: OMAP2+: Remove unused max number of timers definition ARM: OMAP: Remove unnecessary clk structure
2012-07-23Merge tag 'spi' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm-soc spi updates from Arnd Bergmann: "These changes conceptually belong into the spi tree, but we decided to put them into arm-soc to better deal with interdependencies with other platform specific patches that are already there." * tag 'spi' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: spi/s3c64xx: Expand S3C64XX_SPI_{DE,}ACT macros at call sites spi/s3c64xx: Convert to devm_request_and_ioremap() spi/s3c64xx: Put the /CS GPIO into output mode spi/s3c64xx: Fix handling of errors in gpio_request()
2012-07-23Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm-soc device tree description updates from Arnd Bergmann: "This branch contains two kinds of updates: Some platforms in the process of getting converted to device tree based booting, and the platform specific patches necessary for that are included here. Other platforms are already converted, so we just need to update the actual device tree source files and the binding documents to add support for new board and new drivers. In the future we will probably separate those into two branches, and in the long run, the plan is to move the device tree source files out of the kernel repository, but that has to wait until we have completed a much larger portion of the binding documents." Fix up trivial conflicts in arch/arm/mach-imx/clk-imx6q.c due to newly added clkdev registers next to a few removed unnecessary ones. * tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits) ARM: LPC32xx: Add PWM to base dts file ARM: EXYNOS: mark the DMA channel binding for SPI as preliminary ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5 ARM: EXYNOS: Add spi clock support for EXYNOS5 ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4 ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock ARM: ux500: Remove PMU platform registration when booting with DT ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure ARM: ux500: Ensure vendor specific properties have the vendor's identifier pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree ARM: ux500: Apply ab8500-debug node do the db8500 DT structure ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT ...
2012-07-23Merge tag 'dma' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull samsung arm-soc dma changes from Arnd Bergmann: "Some platforms are not yet converted to use the dmaengine framework, including some of the samsung SoCs. In the meantime, we treat this as platform code and merge the patches through the arm-soc tree." * tag 'dma' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: SAMSUNG: Fix compiler warning in dma-ops.c file ASoC: follow the updated samsung DMA common operations spi/s3c64xx: Add the use of DMA config operation ARM: SAMSUNG: Add config() function in DMA common operations
2012-07-23Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull arm soc-specific updates from Arnd Bergmann: "This is stuff that does not fit well into another category and in particular is not related to a particular board. The largest part in here is extending the am33xx support in the omap platform." Fix up trivial conflicts in arch/arm/mach-{imx/mach-mx35_3ds.c, tegra/Makefile} * tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits) ARM: LPC32xx: Add PWM support ARM: LPC32xx: Add PWM clock ARM: LPC32xx: Set system serial based on cpu unique id ARM: vexpress: Config option for early printk console ARM: vexpress: Add Device Tree for V2P-CA15_CA7 core tile ARM: vexpress: Convert V2P-CA15 Device Tree to 64 bit addresses ARM: vexpress: Add fixed regulator for SMSC ARM: vexpress: Add missing SP804 interrupt in motherboard's DTS files ARM: vexpress: Initial common clock support ARM: SAMSUNG: Introduce Kconfig variable for Samsung custom clk API ARM: EXYNOS: Add missing static storage class specifier in pmu.c file ARM: EXYNOS: Make combiner_init function static ARM: EXYNOS: Update HSOTG PHY clock setting for EXYNOS4X12 ARM: versatile: Make plat-versatile clock optional ARM: vexpress: Check master site in daughterboard's sysctl operations ARM: vexpress: remove automatic errata workaround selection ARM: LPC32xx: Adjust to pl08x DMA interface changes ARM: EXYNOS: Clear SYS_WDTRESET bit to use watchdog reset ARM: imx: fix mx51 ehci setup errors ARM: imx: make ehci power/oc polarities configurable ...
2012-07-23Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull general arm-soc cleanups from Arnd Bergmann: "These are all boring changes, moving stuff around or renaming things mostly, and also getting rid of stuff that is duplicate or should not be there to start with. Platform-wise this is all over the place, mainly omap, samsung, at91, imx and tegra." Resolve trivial conflict in arch/arm/mach-omap2/clockdomains3xxx_data.c * tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits) ARM: clps711x: Remove the setting of the time ARM: clps711x: Removed superfluous transform virt_to_bus and related functions ARM: clps711x/p720t: Replace __initcall by .init_early call ARM: S3C24XX: Remove unused GPIO definitions for Openmoko GTA02 board ARM: S3C24XX: Remove unused GPIO definitions for port J ARM: S3C24XX: Remove unused GPA, GPE, GPH bank GPIO aliases ARM: S3C24XX: Convert the touchscreen setup code to common GPIO API ARM: S3C24XX: Convert the PM code to gpiolib API ARM: S3C24XX: Convert QT2410 board file to the gpiolib API ARM: S3C24XX: Convert SMDK board file to the gpiolib API ARM: S3C24XX: Free the backlight gpio requested in Mini2440 board code ARM: imx: remove unused pdata from device macros ARM: imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX_SSI from MACH_MX25_3DS ARM: at91: fix new build errors ARM: at91: add AIC5 support ARM: at91: remove mach/irqs.h ARM: at91: sparse irq support ARM: at91: at91 based machines specify their own irq handler at run time ARM: at91: remove static irq priorities for sam9x5 ARM: at91: add of irq priorities support ...
2012-07-23Merge tag 'fixes-non-critical' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull non-critical arm-soc bug fixes from Arnd Bergmann: "These were submitted as bug fixes before v3.5 but not considered important enough to be included in it." * tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits) ARM:vt8500: Convert to use .restart and remove arch_reset() ARM: davinci: da8xx: fix interrupt handling ARM: OMAP2+: fix CONFIG_CPU_IDLE dependency on CONFIG_PM ARM: mxs/tx28: fix odd include ARM: OMAP: remove unused cpu detection macros ARM: OMAP: fix typos related to OMAP330 ARM: OMAP7XX: Remove omap730.h and omap850.h ARM: OMAP2+: fix naming collision of variable nr_irqs ARM: OMAP: omap2plus_defconfig: Enable EXT4 support ARM: OMAP depends on MMU arm: omap3: am35x: Set proper powerdomain states ARM: OMAP AM35x: clockdomain data: Fix clockdomain dependencies ARM: OMAP AM35x: EMAC/MDIO integration: Add Davinci EMAC/MDIO hwmod support ARM: OMAP: AM35xx: fix UART4 softreset ARM: OMAP AM35xx: clock and hwmod data: fix UART4 data ARM: OMAP AM35xx: clock and hwmod data: fix AM35xx HSOTGUSB hwmod ARM: OMAP: Fix dts files w/ status property: "disable" -> "disabled" ARM: OMAP: beagle: Set USB Host Port 1 to OMAP_USBHS_PORT_MODE_UNUSED ARM: OMAP2: twl-common: Fix compiler warning ARM: OMAP: fix the ads7846 init code ...
2012-07-23Merge tag 'upstream-3.6-rc1' of git://git.infradead.org/linux-ubiLinus Torvalds
Pull UBI changes from Artem Bityutskiy: "Change the default amount of eraseblocks which UBI reserves for bad block handling from 1% to 2%, because 1% does not meet most modern flash requirements. 1% was good enough in the past for old high-quality SLCs, but nowadays 2% is much more appropriate.: Other changes are clean-ups. * tag 'upstream-3.6-rc1' of git://git.infradead.org/linux-ubi: UBI: harmonize the update of ubi->beb_rsvd_pebs UBI: trivial: fix comment of ubi_calculate_reserved function UBI: fix spelling of detach in debug output UBI: Change the default percentage of reserved PEB
2012-07-23Merge tag 'upstream-3.6-rc1' of git://git.infradead.org/linux-ubifsLinus Torvalds
Pull UBIFS updates from Artem Bityutskiy: - Added another debugfs knob for forcing UBIFS R/O mode without flushing caches or finishing commit or any other I/O operation. I've originally added this knob in order to reproduce the free space fixup bug (see commit c6727932cfdb: "UBIFS: fix a bug in empty space fix-up") on nandsim. Without this knob I would have to do real power-cuts, which would make debugging much harder. Then I've decided to keep this knob because it is also useful for UBIFS power-cut recovery end error-paths testing. - Well-spotted fix from Julia. This bug did not cause real troubles for UBIFS, but nevertheless it could cause issues for someone trying to modify the orphans handling code. Kudos to coccinelle! - Minor cleanups. * tag 'upstream-3.6-rc1' of git://git.infradead.org/linux-ubifs: UBIFS: remove invalid reference to list iterator variable UBIFS: simplify reply code a bit UBIFS: add debugfs knob to switch to R/O mode UBIFS: fix compilation warning
2012-07-23locks: fix checking of fcntl_setlease argumentJ. Bruce Fields
The only checks of the long argument passed to fcntl(fd,F_SETLEASE,.) are done after converting the long to an int. Thus some illegal values may be let through and cause problems in later code. [ They actually *don't* cause problems in mainline, as of Dave Jones's commit 8d657eb3b438 "Remove easily user-triggerable BUG from generic_setlease", but we should fix this anyway. And this patch will be necessary to fix real bugs on earlier kernels. ] Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-07-23Merge branch 'for-linus-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull the big VFS changes from Al Viro: "This one is *big* and changes quite a few things around VFS. What's in there: - the first of two really major architecture changes - death to open intents. The former is finally there; it was very long in making, but with Miklos getting through really hard and messy final push in fs/namei.c, we finally have it. Unlike his variant, this one doesn't introduce struct opendata; what we have instead is ->atomic_open() taking preallocated struct file * and passing everything via its fields. Instead of returning struct file *, it returns -E... on error, 0 on success and 1 in "deal with it yourself" case (e.g. symlink found on server, etc.). See comments before fs/namei.c:atomic_open(). That made a lot of goodies finally possible and quite a few are in that pile: ->lookup(), ->d_revalidate() and ->create() do not get struct nameidata * anymore; ->lookup() and ->d_revalidate() get lookup flags instead, ->create() gets "do we want it exclusive" flag. With the introduction of new helper (kern_path_locked()) we are rid of all struct nameidata instances outside of fs/namei.c; it's still visible in namei.h, but not for long. Come the next cycle, declaration will move either to fs/internal.h or to fs/namei.c itself. [me, miklos, hch] - The second major change: behaviour of final fput(). Now we have __fput() done without any locks held by caller *and* not from deep in call stack. That obviously lifts a lot of constraints on the locking in there. Moreover, it's legal now to call fput() from atomic contexts (which has immediately simplified life for aio.c). We also don't need anti-recursion logics in __scm_destroy() anymore. There is a price, though - the damn thing has become partially asynchronous. For fput() from normal process we are guaranteed that pending __fput() will be done before the caller returns to userland, exits or gets stopped for ptrace. For kernel threads and atomic contexts it's done via schedule_work(), so theoretically we might need a way to make sure it's finished; so far only one such place had been found, but there might be more. There's flush_delayed_fput() (do all pending __fput()) and there's __fput_sync() (fput() analog doing __fput() immediately). I hope we won't need them often; see warnings in fs/file_table.c for details. [me, based on task_work series from Oleg merged last cycle] - sync series from Jan - large part of "death to sync_supers()" work from Artem; the only bits missing here are exofs and ext4 ones. As far as I understand, those are going via the exofs and ext4 trees resp.; once they are in, we can put ->write_super() to the rest, along with the thread calling it. - preparatory bits from unionmount series (from dhowells). - assorted cleanups and fixes all over the place, as usual. This is not the last pile for this cycle; there's at least jlayton's ESTALE work and fsfreeze series (the latter - in dire need of fixes, so I'm not sure it'll make the cut this cycle). I'll probably throw symlink/hardlink restrictions stuff from Kees into the next pile, too. Plus there's a lot of misc patches I hadn't thrown into that one - it's large enough as it is..." * 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (127 commits) ext4: switch EXT4_IOC_RESIZE_FS to mnt_want_write_file() btrfs: switch btrfs_ioctl_balance() to mnt_want_write_file() switch dentry_open() to struct path, make it grab references itself spufs: shift dget/mntget towards dentry_open() zoran: don't bother with struct file * in zoran_map ecryptfs: don't reinvent the wheels, please - use struct completion don't expose I_NEW inodes via dentry->d_inode tidy up namei.c a bit unobfuscate follow_up() a bit ext3: pass custom EOF to generic_file_llseek_size() ext4: use core vfs llseek code for dir seeks vfs: allow custom EOF in generic_file_llseek code vfs: Avoid unnecessary WB_SYNC_NONE writeback during sys_sync and reorder sync passes vfs: Remove unnecessary flushing of block devices vfs: Make sys_sync writeout also block device inodes vfs: Create function for iterating over block devices vfs: Reorder operations during sys_sync quota: Move quota syncing to ->sync_fs method quota: Split dquot_quota_sync() to writeback and cache flushing part vfs: Move noop_backing_dev_info check from sync into writeback ...
2012-07-23powerpc/mpic: Create a revmap with enough entries for IPIs and timersBenjamin Herrenschmidt
The current mpic code creates a linear revmap just big enough for all the sources, which happens to miss the IPIs and timers on some machines. This will in turn break when the irqdomain code loses the fallback of doing a linear search when the revmap fails (and really slows down IPIs otherwise). This happens for example on the U4 based Apple machines such as the dual core PowerMac G5s. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-07-23Remove stale .rej fileBenjamin Herrenschmidt
Commit 9778b696a0188ad3b3524b383953ee73b31b7b68 accidentally added a .rej file (probably my fault), remove it. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-07-22Merge tag 'mmc-merge-for-3.6-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc Pull MMC updates from Chris Ball: "MMC highlights for 3.6: Core: - Rename cd-gpio to slot-gpio and extend it to support more slot GPIO functions, such as write-protect. - Add a function to get regulators (Vdd and Vccq) for a host. Drivers: - sdhci-pxav2, sdhci-pxav3: Add device tree support. - sdhi: Add device tree support. - sh_mmcif: Add support for regulators, device tree, slot-gpio. - tmio: Add regulator support, use slot-gpio." * tag 'mmc-merge-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (62 commits) mmc: sdhci-dove: Prepare for common clock framework mmc: sdhci-dove: Add SDHCI_QUIRK_NO_HISPD_BIT mmc: omap_hsmmc: ensure probe returns error upon resource failure mmc: mxs-mmc: Add wp-inverted property mmc: esdhc: Fix DMA_MASK to not break mx25 DMA access mmc: core: reset signal voltage on power up mmc: sd: Fix sd current limit setting mmc: omap_hsmmc: add clk_prepare and clk_unprepare mmc: sdhci: When a UHS switch fails, cycle power if regulator is used mmc: atmel-mci: modify CLKDIV displaying in debugfs mmc: atmel-mci: fix incorrect setting of host->data to NULL mmc: sdhci: poll for card even when card is logically unremovable mmc: sdhci: Introduce new flag SDHCI_USING_RETUNING_TIMER mmc: sdio: Change pr_warning to pr_warn_ratelimited mmc: core: Simplify and fix for SD switch processing mmc: sdhci: restore host settings when card is removed mmc: sdhci: fix incorrect command used in tuning mmc: sdhci-pci: CaFe has broken card detection mmc: sdhci: Report failure reasons for all cases in sdhci_add_host() mmc: s3cmci: Convert s3cmci driver to gpiolib API ...
2012-07-22Merge branch 'x86-mce-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86/mce changes from Ingo Molnar: "This tree improves the AMD thresholding bank code and includes a memory fault signal handling fixlet." * 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/mce: Fix siginfo_t->si_addr value for non-recoverable memory faults x86, MCE, AMD: Update copyrights and boilerplate x86, MCE, AMD: Give proper names to the thresholding banks x86, MCE, AMD: Make error_count read only x86, MCE, AMD: Cleanup reading of error_count x86, MCE, AMD: Print decimal thresholding values x86, MCE, AMD: Move shared bank to node descriptor x86, MCE, AMD: Remove local_allocate_... wrapper x86, MCE, AMD: Remove shared banks sysfs linking x86, amd_nb: Export model 0x10 and later PCI id
2012-07-22mmc: sdhci-dove: Prepare for common clock frameworkSebastian Hesselbarth
As mach-dove is moving towards common clock framework prepare the sdhci driver to grab its clock. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-22mmc: sdhci-dove: Add SDHCI_QUIRK_NO_HISPD_BITSebastian Hesselbarth
The sdio controller on dove doesn't have a bit to indicate high-speed. With the quirk set it fixes accessing high-speed sdcards. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-22mmc: omap_hsmmc: ensure probe returns error upon resource failureKevin Hilman
If platform_get_resource_by_name() fails, driver probe is aborted an should return an error so the driver is not bound to the device. However, in the current error path of platform_get_resource_by_name(), probe returns zero since the return value (ret) is not properly set. With a zero return value, the driver core assumes probe was successful and will bind the driver to the device. Fix this by ensuring that probe returns an error code in this failure path. Signed-off-by: Kevin Hilman <khilman@ti.com> Acked-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-22mmc: mxs-mmc: Add wp-inverted propertyMarek Vasut
The write-protect GPIO is inverted on some boards. Handle such case. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-22mmc: esdhc: Fix DMA_MASK to not break mx25 DMA accessWilson Callan
Patch to not set reserved bits in i.MX25 PROCTL register. DMA stops working if those bits get set. Signed-off-by: Wilson Callan <wilson.callan@savantsystems.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>