| Age | Commit message (Collapse) | Author |
|---|
|
We really don't need to delay an entire millisecond just to get into our
critical section. A microsecond will be sufficient, thank you.
Change-ID: I2d02ece6610007d98cabcb3f42df9a774bb54e59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The hardware design requires that the driver avoid indicating
checksum offload success on some ipv6 frames with extension
headers.
The code needs to just check for the IPV6EXADD bit and if
it is set punt the checksum to the stack. I don't know why
the code was checking TCP on inner protocol, as that code
doesn't make any sense to me but seems wrong, so remove it.
Change-ID: I10d3aacdbb1819fb60b4b0eb80e6cc67ef2c9599
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This implements a state machine intended to support the userland tool for
updating the device eeprom. The state machine implements one-shot reads,
writes, multi-step write sessions, and checksum requests. If we're in the middle
of a multi-step write session, no one should fire off other writes, however, one
shot reads are valid. The userland tool is expected to keep track of its session
status, arrange the placement and ordering of the writes, and deal with the
checksum requirement.
This patch also adds nvmupdate support to ethtool callbacks.
The get_eeprom() and set_eeprom() services in ethtool are used here to
facilitate the userland NVMUpdate tool. The 'magic' value in the get and
set commands is used to pass additional control information for managing
the read and write steps.
The read operation works both as normally expected in the standard ethtool
method, as well as with the extra NVM controls. The write operation
works only for the expanded NVM functions - the normal ethtool method is
not allowed because of the NVM semaphore management needed for multipart
writes, as well as the checksum requirement.
Change-ID: I1d84a170153a9f437906744e2e350fd68fe7563d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
spotted by cppcheck
Signed-off-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump version number.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a check and prints the error cause register value when
the hardware detects a malformed packet. This is a very unlikely
scenario but has been seen occasionally, so printing the message to
assist the user.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch prevents the display of the minimum link qualification check
if we might be in a virtual machine. This check is incorrect and
misleading in this case, since we actually don't really know what the
available bandwidth is. To do so, we simply check whether each function
on the bus matches our device id. If it doesn't the most likely scenario
is that we're directly assigned to a virtual machine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix a bug in the misuse of the list_for_each macro to loop over every
entry in the bus_list. Instead of attempting to loop over the list from
a random entry point, go up to the bus and use the real list_head entry
point. This prevents the possible read or write of unallocated or
incorrectly addressed memory.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Change some uses of strncpy to use the more appropriate strlcpy
when clearing is not needed to prevent information leakage. Also
change some length arguments to use the preferred sizeof form.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In ixgbe_probe, the code at label err_dma can dereference adapter
when it has a NULL value. The check is there to avoid disabling a
disabled device. When adapter is NULL, treat it as if the device
is enabled, because it is enabled in that case.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Alexei Starovoitov says:
====================
I believe my recent set of RFC/patches [1] provided good visibility on where
I would like to take eBPF subsystem. These two trivial patches is a first step
in that direction:
patch 1 - mechanical split of eBPF interpreter out of filter.c
patch 2 - nominate myself as a maintainer for eBPF core pieces
In the foreseeable future eBPF patches will be going through net-next,
so put netdev as a primary mailing list
[1] git://git.kernel.org/pub/scm/linux/kernel/git/ast/bpf master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BPF is used in several kernel components. This split creates logical boundary
between generic eBPF core and the rest
kernel/bpf/core.c: eBPF interpreter
net/core/filter.c: classic->eBPF converter, classic verifiers, socket filters
This patch only moves functions.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
net: bcmgenet: checkpatch fixes
This patch series contains cleanups for CHECK and WARNINGS reported by
checkpatch.pl. I removed one patch from this series since Joe reported
this was a false positive due to me not using the latest version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were two places that used kzalloc() with a multiplied sizeof(),
replace these with kcalloc as recommended by checkpatch.pl.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
checkpatch.pl flagged two locations that did not comply to "CHECK:
braces {} should be used on all arms of this statement", fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
checkpatch.pl flagged two blank lines which are not needed, and one that
was missing, fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
checkpatch.pl flagged a lot of "CHECK: Alignment should match open
parenthesis" checks, fix all of them to make the driver neater. While
at it fix some obvious typos and re-arrange some of the lines to avoid
going over 80 columns.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a smaller GPLv2 header and remove all the boilerplate code as well
as the FSF mail address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, although IP_MULTICAST_ALL and IP_MSFILTER ioctl calls succeed on
raw sockets, there is no code to implement the functionality on received
packets; it is only implemented for UDP sockets. The raw(7) man page states:
"In addition, all ip(7) IPPROTO_IP socket options valid for datagram sockets
are supported", which implies these ioctls should work on raw sockets.
To fix this, add a call to ip_mc_sf_allow on raw sockets.
This should not break any existing code, since the current position of
not calling ip_mc_sf_filter makes it behave as if neither the IP_MULTICAST_ALL
nor the IP_MSFILTER ioctl had been called. Adding the call to ip_mc_sf_allow
will therefore maintain the current behaviour so long as IP_MULTICAST_ALL and
IP_MSFILTER ioctls are not called. Any code that currently is calling
IP_MULTICAST_ALL or IP_MSFILTER ioctls on raw sockets presumably is wanting
the filter to be applied, although no filtering will currently be occurring.
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jason Wang says:
====================
rx busy polling support for virtio-net
This series introduces the support for rx busy polling support. This
was useful for reducing the latency for a kvm guest. Instead of
introducing new states and spinlocks, this series re-uses NAPI state
to synchonrize between NAPI and busy polling. This grealy simplified
the codes and reduce the overheads of spinlocks for normal NAPI fast
path.
Test was done between a kvm guest and an external host. Two hosts were
connected through 40gb mlx4 cards. With both busy_poll and busy_read
are set to 50 in guest, 1 byte netperf tcp_rr shows 127% improvement:
transaction rate was increased from 8353.33 to 18966.87.
Changes from V2:
- Avoid introducing new states and spinlocks by reusuing the NAPI
state
- Fix the budget calculation in virtnet_poll()
- Drop patch 1/3 from V2 since it was useless
Changes from V1:
- split the patch info smaller ones
- add more details about test setup/configuration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic support for rx busy polling. Instead of introducing new
states and spinlock to synchronize between NAPI and polling method,
this patch just reuse NAPI state to avoid extra overhead for fast path
and simplified the codes.
Test was done between a kvm guest and an external host. Two hosts were
connected through 40gb mlx4 cards. With both busy_poll and busy_read
are set to 50 in guest, 1 byte netperf tcp_rr shows 127% improvement:
transaction rate was increased from 8353.33 to 18966.87.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move common receive logic to a new helper virtnet_receive(). It will
also be used by rx busy polling method.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch use the struct pci_device_id instead of using macro
DEFINE_PCI_DEVICE_TABLE which is deprecated and should not be used.
And also moves these ids after probe and remove functionalities.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts to use the macro module_pci_driver, which makes
the code smaller and simpler.
Previously in this driver we are having driver version info will be
printed log buffer based on whether the driver selected as module
or statically into image itself. By using the module_pci_driver that
part of the code removed. For the first time of the device init,
we are making the version info to be printed once.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It hasn't been used since commit 0fd7bac(net: relax rcvbuf limits).
Signed-off-by: Sorin Dumitru <sorin@returnze.ro>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to view addresses added by the driver and learnt by the
hardware from ALE table via ethtool register dump interface.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When timestamping received packets, rx_timestamp_work may be scheduled
before the timestamps is received from the hardware resulting in the
packet beeing delivered without the timestamp.
This is fixed by changing the receive timestamp path:
On receiving a packet that need timestamping, the rxts list is
traversed. If a match is found, packet+timestamp are delivered,
otherwise the packet is added to a rx_queue.
When a timestamp arrives rx_queue is traversed and if a matching
packet is found, it is delivered with the timestamp. Otherwise the
timestamp is added to the rxts list for matching with packets arriving
later.
In case the hardware drops a timestamp, a workqueue regularly checks
the queue for old packets and delivers them without a timestamp.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the sfc driver code for implementing busy polling.
It adds ndo_busy_poll method and locking between it and napi poll.
It also adds each napi to the napi_hash right after netif_napi_add().
Uses efx_start_eventq and efx_stop_eventq in the self tests.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Amir Vadai says:
====================
Mellanox driver update Jul-22-2014
This patchset contains a fix by Eyal to fix a bug in mlx4_en with bonding
alb/tlb mode.
The second patch, by me, is an ethtool private flag that enable turning off the
BlueFlame hardware feature.
The last two patches, introduce a new low memory profile for mlx4_en and
mlx4_core. This mode is useful when running from a limited resources
environment, like kdump. This will reduce the memory consumed by both drivers
from more than 100M to ~30M.
This patchset was applied and tested on commit 575a193 ("net: mvpp2: Fix error
return code in mvpp2_probe")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When memory is limited, reduce number of rx and tx rings.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in kdump kernel, reduce number of resources allocated for
the hardware. This will enable the NIC to operate in this low memory
environment at the expense of performance and some features not related
to the basic NIC functionality.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable the user to turn off the hardware feature called BlueFlame.
Since it is something specific to mlx4_en hardware, we control
the feature via ethtool private flags.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When port is down dev_addr is changed (e.g. by bonding) but current_mac
is not touched. When port is up again, hash_mac is updated to dev_addr,
but current_mac isn't. This leads to inconsistency between current_mac
and mac_hash. Because of that, mlx4_en_replace_mac() fails to find
current_mac in mac_hash.
Fix is to reset current_mac to dev_addr when port is up - as we do for
mac_hash.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that all the users of mvpp2_bm_bufs_free() have been fixed, we can safely
clean the function prototype.
The function is always called to release all the buffers in a BM pool, and
the number of buffers freed is not needed. Therefore, we change the return
to a void, and remove the "num" parameter. This is a cosmetic change, to
make the code slightly cleaner.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After a call to mvpp2_bm_bufs_free(), the caller usually wants to know
if the function successfully freed the requested number. However, this
cannot be done by looking into the BM pool count, because the current
buffer count was updated by mvpp2_bm_bufs_free().
In fact, the current callers of mvpp2_bm_bufs_free() use it to release
all the buffers in the pool, so we can fix this by simply checking
if the pool is not empty.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the network interfaces that are not configured by the bootloader
(using e.g. tftp or ping) can detect the link status but are unable to
transmit data.
The network controller has a functionality that allows the hardware to
continuously poll the PHY and directly update the MAC configuration accordingly
(speed, duplex, etc.). However, this doesn't work well with phylib's
software-based polling and updating MAC configuration in the driver's callback.
This commit fixes this issue by:
1. Setting MVPP2_PHY_AN_STOP_SMI0_MASK in MVPP2_PHY_AN_CFG0_REG in
mvpp2_init(), which disables the harware polling feature.
2. Disabling MVPP2_GMAC_PCS_ENABLE_MASK bit in MVPP2_GMAC_CTRL_2_REG in
mvpp2_port_mii_set() for port types other than SGMII.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This bit was originally wrong, the correct value is BIT(1), so fix it.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ALIGN from linux/kernel.h to define SKB_DATA_ALIGN instead of open
coding it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MSG_MORE and 'corking' a socket would require that the transmit of
a data chunk be delayed.
Rename the return value to be less specific.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check for Nagle contains 6 separate checks all of which must be true
before a data packet is delayed.
Separate out each into its own 'if (test) return SCTP_XMIT_OK' so that
the reasons can be individually described.
Also return directly with SCTP_XMIT_RWND_FULL.
Delete the now-unused 'retval' variable and 'finish' label from
sctp_packet_can_append_data().
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Null termination fix in dns_resolver got the pointer dereferncing
wrong, fix from Ben Hutchings.
2) ip_options_compile() has a benign but real buffer overflow when
parsing options. From Eric Dumazet.
3) Table updates can crash in netfilter's nftables if none of the state
flags indicate an actual change, from Pablo Neira Ayuso.
4) Fix race in nf_tables dumping, also from Pablo.
5) GRE-GRO support broke the forwarding path because the segmentation
state was not fully initialized in these paths, from Jerry Chu.
6) sunvnet driver leaks objects and potentially crashes on module
unload, from Sowmini Varadhan.
7) We can accidently generate the same handle for several u32
classifier filters, fix from Cong Wang.
8) Several edge case bug fixes in fragment handling in xen-netback,
from Zoltan Kiss.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
ipv4: fix buffer overflow in ip_options_compile()
batman-adv: fix TT VLAN inconsistency on VLAN re-add
batman-adv: drop QinQ claim frames in bridge loop avoidance
dns_resolver: Null-terminate the right string
xen-netback: Fix pointer incrementation to avoid incorrect logging
xen-netback: Fix releasing header slot on error path
xen-netback: Fix releasing frag_list skbs in error path
xen-netback: Fix handling frag_list on grant op error path
net_sched: avoid generating same handle for u32 filters
net: huawei_cdc_ncm: add "subclass 3" devices
net: qmi_wwan: add two Sierra Wireless/Netgear devices
wan/x25_asy: integer overflow in x25_asy_change_mtu()
net: ppp: fix creating PPP pass and active filters
net/mlx4_en: cq->irq_desc wasn't set in legacy EQ's
sunvnet: clean up objects created in vnet_new() on vnet_exit()
r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_40
net-gre-gro: Fix a bug that breaks the forwarding path
netfilter: nf_tables: 64bit stats need some extra synchronization
netfilter: nf_tables: set NLM_F_DUMP_INTR if netlink dumping is stale
netfilter: nf_tables: safe RCU iteration on list when dumping
...
|
|
Pull sparc fix from David Miller:
"Need to hook up the new renameat2 system call"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Hook up renameat2 syscall.
|
|
Pull IDE fixes from David Miller:
- fix interrupt registry for some Atari IDE chipsets.
- adjust Kconfig dependencies for x86_32 specific chips.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: Fix SC1200 dependencies
ide: Fix CS5520 and CS5530 dependencies
m68k/atari - ide: do not register interrupt if host->get_lock is set
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull trace fix from Steven Rostedt:
"Tony Luck found that using the "uptime" trace clock that uses jiffies
as a counter was converted to nanoseconds (silly), and after 1 hour 11
minutes and 34 seconds, this monotonic clock would wrap, causing havoc
with the tracing system and making the clock useless.
He converted that clock to use jiffies_64 and made it into a counter
instead of nanosecond conversions, and displayed the clock with the
straight jiffy count, which works much better than it did in the past"
* tag 'trace-fixes-v3.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix wraparound problems in "uptime" trace clock
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hariprasad Shenai says:
====================
Misc. fix for cxgb4 and iw_cxgb4
This patch series adds support to enchance error reporting, log detailed
warning for negative advice, support query_qp verb and advertise correct
device max attributes for iwarp.
The patches series is created against 'net-next' tree.
And includes patches on cxgb4 and iw_cxgb4 driver.
Since this patch-series contains changes which are dependent on commit id
4c2c5763 ("cxgb4/iw_cxgb4: use firmware ord/ird resource limits") of net-next
tree we would like to request this patch series to get merged via David Miller's
'net-next' tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the size advertised by FW
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise the actual max limits for things like qp depths, number of
qps, cqs, etc.
Clean up the queue allocation for qps and cqs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
