aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-01-23Merge remote-tracking branch 'lsk/v3.14/topic/arm64-efi' into ↵lsk-v3.14-15.01Mark Brown
linux-linaro-lsk-v3.14 Conflicts: arch/arm64/kernel/Makefile drivers/firmware/efi/efi-stub-helper.c
2015-01-23Merge remote-tracking branch 'lsk/v3.14/topic/coresight' into ↵Mark Brown
linux-linaro-lsk-v3.14
2015-01-23ARM: Revert "coresight: adding basic support for Vexpress TC2"Mark Brown
This reverts commit 19bdec7dbcccfe2d0aed8cba3e1e8597b7fd8c88, for some reason this is causing boot failures on TC2 when booted using UEFI. Revert pending investigation. Signed-off-by: Mark Brown <broonie@kernel.org>
2015-01-16Merge tag 'v3.14.29' into linux-linaro-lsk-v3.14Mark Brown
This is the 3.14.29 stable release
2015-01-16Linux 3.14.29v3.14.29Greg Kroah-Hartman
2015-01-16mm: Don't count the stack guard page towards RLIMIT_STACKLinus Torvalds
commit 690eac53daff34169a4d74fc7bfbd388c4896abb upstream. Commit fee7e49d4514 ("mm: propagate error from stack expansion even for guard page") made sure that we return the error properly for stack growth conditions. It also theorized that counting the guard page towards the stack limit might break something, but also said "Let's see if anybody notices". Somebody did notice. Apparently android-x86 sets the stack limit very close to the limit indeed, and including the guard page in the rlimit check causes the android 'zygote' process problems. So this adds the (fairly trivial) code to make the stack rlimit check be against the actual real stack size, rather than the size of the vma that includes the guard page. Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org> Cc: Jay Foad <jay.foad@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16mm: propagate error from stack expansion even for guard pageLinus Torvalds
commit fee7e49d45149fba60156f5b59014f764d3e3728 upstream. Jay Foad reports that the address sanitizer test (asan) sometimes gets confused by a stack pointer that ends up being outside the stack vma that is reported by /proc/maps. This happens due to an interaction between RLIMIT_STACK and the guard page: when we do the guard page check, we ignore the potential error from the stack expansion, which effectively results in a missing guard page, since the expected stack expansion won't have been done. And since /proc/maps explicitly ignores the guard page (commit d7824370e263: "mm: fix up some user-visible effects of the stack guard page"), the stack pointer ends up being outside the reported stack area. This is the minimal patch: it just propagates the error. It also effectively makes the guard page part of the stack limit, which in turn measn that the actual real stack is one page less than the stack limit. Let's see if anybody notices. We could teach acct_stack_growth() to allow an extra page for a grow-up/grow-down stack in the rlimit test, but I don't want to add more complexity if it isn't needed. Reported-and-tested-by: Jay Foad <jay.foad@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16mm, vmscan: prevent kswapd livelock due to pfmemalloc-throttled process ↵Vlastimil Babka
being killed commit 9e5e3661727eaf960d3480213f8e87c8d67b6956 upstream. Charles Shirron and Paul Cassella from Cray Inc have reported kswapd stuck in a busy loop with nothing left to balance, but kswapd_try_to_sleep() failing to sleep. Their analysis found the cause to be a combination of several factors: 1. A process is waiting in throttle_direct_reclaim() on pgdat->pfmemalloc_wait 2. The process has been killed (by OOM in this case), but has not yet been scheduled to remove itself from the waitqueue and die. 3. kswapd checks for throttled processes in prepare_kswapd_sleep(): if (waitqueue_active(&pgdat->pfmemalloc_wait)) { wake_up(&pgdat->pfmemalloc_wait); return false; // kswapd will not go to sleep } However, for a process that was already killed, wake_up() does not remove the process from the waitqueue, since try_to_wake_up() checks its state first and returns false when the process is no longer waiting. 4. kswapd is running on the same CPU as the only CPU that the process is allowed to run on (through cpus_allowed, or possibly single-cpu system). 5. CONFIG_PREEMPT_NONE=y kernel is used. If there's nothing to balance, kswapd encounters no voluntary preemption points and repeatedly fails prepare_kswapd_sleep(), blocking the process from running and removing itself from the waitqueue, which would let kswapd sleep. So, the source of the problem is that we prevent kswapd from going to sleep until there are processes waiting on the pfmemalloc_wait queue, and a process waiting on a queue is guaranteed to be removed from the queue only when it gets scheduled. This was done to make sure that no process is left sleeping on pfmemalloc_wait when kswapd itself goes to sleep. However, it isn't necessary to postpone kswapd sleep until the pfmemalloc_wait queue actually empties. To prevent processes from being left sleeping, it's actually enough to guarantee that all processes waiting on pfmemalloc_wait queue have been woken up by the time we put kswapd to sleep. This patch therefore fixes this issue by substituting 'wake_up' with 'wake_up_all' and removing 'return false' in the code snippet from prepare_kswapd_sleep() above. Note that if any process puts itself in the queue after this waitqueue_active() check, or after the wake up itself, it means that the process will also wake up kswapd - and since we are under prepare_to_wait(), the wake up won't be missed. Also we update the comment prepare_kswapd_sleep() to hopefully more clearly describe the races it is preventing. Fixes: 5515061d22f0 ("mm: throttle direct reclaimers if PF_MEMALLOC reserves are low and swap is backed by network storage") Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Acked-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16mmc: sdhci: Fix sleep in atomic after inserting SD cardKrzysztof Kozlowski
commit 2836766a9d0bd02c66073f8dd44796e6cc23848d upstream. Sleep in atomic context happened on Trats2 board after inserting or removing SD card because mmc_gpio_get_cd() was called under spin lock. Fix this by moving card detection earlier, before acquiring spin lock. The mmc_gpio_get_cd() call does not have to be protected by spin lock because it does not access any sdhci internal data. The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After moving it out side of spin lock it could theoretically race with driver removal but still there is no actual protection against manual card eject. Dmesg after inserting SD card: [ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511 [ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1 [ 41.677580] INFO: lockdep is turned off. [ 41.681486] irq event stamp: 61972 [ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c [ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54 [ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8 [ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114 [ 41.716206] Preemption disabled at:[< (null)>] (null) [ 41.721500] [ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883 [ 41.732111] Workqueue: kmmcd mmc_rescan [ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14) [ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc) [ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30) [ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58) [ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4) [ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268) [ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0) [ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78) [ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124) [ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64) [ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4) [ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4) [ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0) [ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104) [ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c) [ 42.038276] mmc0: new high speed SDHC card at address 1234 Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 94144a465dd0 ("mmc: sdhci: add get_cd() implementation") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16spi: fsl: Fix problem with multi message transfersStefan Roese
commit 4302a59629f7a0bd70fd1605d2b558597517372a upstream. When used via spidev with more than one messages to tranfer via SPI_IOC_MESSAGE the current implementation would return with -EINVAL, since bits_per_word and speed_hz are set in all transfer structs. And in the 2nd loop status will stay at -EINVAL as its not overwritten again via fsl_spi_setup_transfer(). This patch changes this behavious by first checking if one of the messages uses different settings. If this is the case the function will return with -EINVAL. If not, the messages are transferred correctly. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org> Cc: Esben Haabendal <esbenhaabendal@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16perf session: Do not fail on processing out of order eventJiri Olsa
commit f61ff6c06dc8f32c7036013ad802c899ec590607 upstream. Linus reported perf report command being interrupted due to processing of 'out of order' event, with following error: Timestamp below last timeslice flush 0x5733a8 [0x28]: failed to process type: 3 I could reproduce the issue and in my case it was caused by one CPU (mmap) being behind during record and userspace mmap reader seeing the data after other CPUs data were already stored. This is expected under some circumstances because we need to limit the number of events that we queue for reordering when we receive a PERF_RECORD_FINISHED_ROUND or when we force flush due to memory pressure. Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Ingo Molnar <mingo@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt.fleming@intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/r/1417016371-30249-1-git-send-email-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> [zhangzhiqiang: backport to 3.10: - adjust context - commit f61ff6c06d struct events_stats was defined in tools/perf/util/event.h while 3.10 stable defined in tools/perf/util/hist.h. - 3.10 stable there is no pr_oe_time() which used for debug. - After the above adjustments, becomes same to the original patch: https://github.com/torvalds/linux/commit/f61ff6c06dc8f32c7036013ad802c899ec590607 ] Signed-off-by: Zhiqiang Zhang <zhangzhiqiang.zhang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16perf: Fix events installation during moving groupJiri Olsa
commit 9fc81d87420d0d3fd62d5e5529972c0ad9eab9cc upstream. We allow PMU driver to change the cpu on which the event should be installed to. This happened in patch: e2d37cd213dc ("perf: Allow the PMU driver to choose the CPU on which to install events") This patch also forces all the group members to follow the currently opened events cpu if the group happened to be moved. This and the change of event->cpu in perf_install_in_context() function introduced in: 0cda4c023132 ("perf: Introduce perf_pmu_migrate_context()") forces group members to change their event->cpu, if the currently-opened-event's PMU changed the cpu and there is a group move. Above behaviour causes problem for breakpoint events, which uses event->cpu to touch cpu specific data for breakpoints accounting. By changing event->cpu, some breakpoints slots were wrongly accounted for given cpu. Vinces's perf fuzzer hit this issue and caused following WARN on my setup: WARNING: CPU: 0 PID: 20214 at arch/x86/kernel/hw_breakpoint.c:119 arch_install_hw_breakpoint+0x142/0x150() Can't find any breakpoint slot [...] This patch changes the group moving code to keep the event's original cpu. Reported-by: Vince Weaver <vince@deater.net> Signed-off-by: Jiri Olsa <jolsa@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Vince Weaver <vince@deater.net> Cc: Yan, Zheng <zheng.z.yan@intel.com> Link: http://lkml.kernel.org/r/1418243031-20367-3-git-send-email-jolsa@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16perf/x86/intel/uncore: Make sure only uncore events are collectedJiri Olsa
commit af91568e762d04931dcbdd6bef4655433d8b9418 upstream. The uncore_collect_events functions assumes that event group might contain only uncore events which is wrong, because it might contain any type of events. This bug leads to uncore framework touching 'not' uncore events, which could end up all sorts of bugs. One was triggered by Vince's perf fuzzer, when the uncore code touched breakpoint event private event space as if it was uncore event and caused BUG: BUG: unable to handle kernel paging request at ffffffff82822068 IP: [<ffffffff81020338>] uncore_assign_events+0x188/0x250 ... The code in uncore_assign_events() function was looking for event->hw.idx data while the event was initialized as a breakpoint with different members in event->hw union. This patch forces uncore_collect_events() to collect only uncore events. Reported-by: Vince Weaver <vince@deater.net> Signed-off-by: Jiri Olsa <jolsa@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Yan, Zheng <zheng.z.yan@intel.com> Link: http://lkml.kernel.org/r/1418243031-20367-2-git-send-email-jolsa@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16Btrfs: don't delay inode ref updates during log replayChris Mason
commit 6f8960541b1eb6054a642da48daae2320fddba93 upstream. Commit 1d52c78afbb (Btrfs: try not to ENOSPC on log replay) added a check to skip delayed inode updates during log replay because it confuses the enospc code. But the delayed processing will end up ignoring delayed refs from log replay because the inode itself wasn't put through the delayed code. This can end up triggering a warning at commit time: WARNING: CPU: 2 PID: 778 at fs/btrfs/delayed-inode.c:1410 btrfs_assert_delayed_root_empty+0x32/0x34() Which is repeated for each commit because we never process the delayed inode ref update. The fix used here is to change btrfs_delayed_delete_inode_ref to return an error if we're currently in log replay. The caller will do the ref deletion immediately and everything will work properly. Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16arm64: kernel: fix __cpu_suspend mm switch on warm-bootLorenzo Pieralisi
commit f43c27188a49111b58e9611afa2f0365b0b55625 upstream. On arm64 the TTBR0_EL1 register is set to either the reserved TTBR0 page tables on boot or to the active_mm mappings belonging to user space processes, it must never be set to swapper_pg_dir page tables mappings. When a CPU is booted its active_mm is set to init_mm even though its TTBR0_EL1 points at the reserved TTBR0 page mappings. This implies that when __cpu_suspend is triggered the active_mm can point at init_mm even if the current TTBR0_EL1 register contains the reserved TTBR0_EL1 mappings. Therefore, the mm save and restore executed in __cpu_suspend might turn out to be erroneous in that, if the current->active_mm corresponds to init_mm, on resume from low power it ends up restoring in the TTBR0_EL1 the init_mm mappings that are global and can cause speculation of TLB entries which end up being propagated to user space. This patch fixes the issue by checking the active_mm pointer before restoring the TTBR0 mappings. If the current active_mm == &init_mm, the code sets the TTBR0_EL1 to the reserved TTBR0 mapping instead of switching back to the active_mm, which is the expected behaviour corresponding to the TTBR0_EL1 settings when __cpu_suspend was entered. Fixes: 95322526ef62 ("arm64: kernel: cpu_{suspend/resume} implementation") Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16arm64: Move cpu_resume into the text sectionLaura Abbott
commit c3684fbb446501b48dec6677a6a9f61c215053de upstream. The function cpu_resume currently lives in the .data section. There's no reason for it to be there since we can use relative instructions without a problem. Move a few cpu_resume data structures out of the assembly file so the .data annotation can be dropped completely and cpu_resume ends up in the read only text section. Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Tested-by: Kees Cook <keescook@chromium.org> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16arm64: kernel: refactor the CPU suspend API for retention statesLorenzo Pieralisi
commit 714f59925595b9c2ea9c22b107b340d38e3b3bc9 upstream. CPU suspend is the standard kernel interface to be used to enter low-power states on ARM64 systems. Current cpu_suspend implementation by default assumes that all low power states are losing the CPU context, so the CPU registers must be saved and cleaned to DRAM upon state entry. Furthermore, the current cpu_suspend() implementation assumes that if the CPU suspend back-end method returns when called, this has to be considered an error regardless of the return code (which can be successful) since the CPU was not expected to return from a code path that is different from cpu_resume code path - eg returning from the reset vector. All in all this means that the current API does not cope well with low-power states that preserve the CPU context when entered (ie retention states), since first of all the context is saved for nothing on state entry for those states and a successful state entry can return as a normal function return, which is considered an error by the current CPU suspend implementation. This patch refactors the cpu_suspend() API so that it can be split in two separate functionalities. The arm64 cpu_suspend API just provides a wrapper around CPU suspend operation hook. A new function is introduced (for architecture code use only) for states that require context saving upon entry: __cpu_suspend(unsigned long arg, int (*fn)(unsigned long)) __cpu_suspend() saves the context on function entry and calls the so called suspend finisher (ie fn) to complete the suspend operation. The finisher is not expected to return, unless it fails in which case the error is propagated back to the __cpu_suspend caller. The API refactoring results in the following pseudo code call sequence for a suspending CPU, when triggered from a kernel subsystem: /* * int cpu_suspend(unsigned long idx) * @idx: idle state index */ { -> cpu_suspend(idx) |---> CPU operations suspend hook called, if present |--> if (retention_state) |--> direct suspend back-end call (eg PSCI suspend) else |--> __cpu_suspend(idx, &back_end_finisher); } By refactoring the cpu_suspend API this way, the CPU operations back-end has a chance to detect whether idle states require state saving or not and can call the required suspend operations accordingly either through simple function call or indirectly through __cpu_suspend() which carries out state saving and suspend finisher dispatching to complete idle state entry. Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16arm64: kernel: add missing __init section marker to cpu_suspend_initLorenzo Pieralisi
commit 18ab7db6b749ac27aac08d572afbbd2f4d937934 upstream. Suspend init function must be marked as __init, since it is not needed after the kernel has booted. This patch moves the cpu_suspend_init() function to the __init section. Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ACPI / PM: Fix PM initialization for devices that are not presentRafael J. Wysocki
commit 1b1f3e1699a9886f1070f94171097ab4ccdbfc95 upstream. If an ACPI device object whose _STA returns 0 (not present and not functional) has _PR0 or _PS0, its power_manageable flag will be set and acpi_bus_init_power() will return 0 for it. Consequently, if such a device object is passed to the ACPI device PM functions, they will attempt to carry out the requested operation on the device, although they should not do that for devices that are not present. To fix that problem make acpi_bus_init_power() return an error code for devices that are not present which will cause power_manageable to be cleared for them as appropriate in acpi_bus_get_power_flags(). However, the lists of power resources should not be freed for the device in that case, so modify acpi_bus_get_power_flags() to keep those lists even if acpi_bus_init_power() returns an error. Accordingly, when deciding whether or not the lists of power resources need to be freed, acpi_free_power_resources_lists() should check the power.flags.power_resources flag instead of flags.power_manageable, so make that change too. Furthermore, if acpi_bus_attach() sees that flags.initialized is unset for the given device, it should reset the power management settings of the device and re-initialize them from scratch instead of relying on the previous settings (the device may have appeared after being not present previously, for example), so make it use the 'valid' flag of the D0 power state as the initial value of flags.power_manageable for it and call acpi_bus_init_power() to discover its current power state. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ARM: mvebu: disable I/O coherency on non-SMP situations on Armada 370/375/38x/XPThomas Petazzoni
commit e55355453600a33bb5ca4f71f2d7214875f3b061 upstream. Enabling the hardware I/O coherency on Armada 370, Armada 375, Armada 38x and Armada XP requires a certain number of conditions: - On Armada 370, the cache policy must be set to write-allocate. - On Armada 375, 38x and XP, the cache policy must be set to write-allocate, the pages must be mapped with the shareable attribute, and the SMP bit must be set Currently, on Armada XP, when CONFIG_SMP is enabled, those conditions are met. However, when Armada XP is used in a !CONFIG_SMP kernel, none of these conditions are met. With Armada 370, the situation is worse: since the processor is single core, regardless of whether CONFIG_SMP or !CONFIG_SMP is used, the cache policy will be set to write-back by the kernel and not write-allocate. Since solving this problem turns out to be quite complicated, and we don't want to let users with a mainline kernel known to have infrequent but existing data corruptions, this commit proposes to simply disable hardware I/O coherency in situations where it is known not to work. And basically, the is_smp() function of the kernel tells us whether it is OK to enable hardware I/O coherency or not, so this commit slightly refactors the coherency_type() function to return COHERENCY_FABRIC_TYPE_NONE when is_smp() is false, or the appropriate type of the coherency fabric in the other case. Thanks to this, the I/O coherency fabric will no longer be used at all in !CONFIG_SMP configurations. It will continue to be used in CONFIG_SMP configurations on Armada XP, Armada 375 and Armada 38x (which are multiple cores processors), but will no longer be used on Armada 370 (which is a single core processor). In the process, it simplifies the implementation of the coherency_type() function, and adds a missing call to of_node_put(). Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: e60304f8cb7bb545e79fe62d9b9762460c254ec2 ("arm: mvebu: Add hardware I/O Coherency support") Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Link: https://lkml.kernel.org/r/1415871540-20302-3-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16Revert "ARM: 7830/1: delay: don't bother reporting bogomips in /proc/cpuinfo"Pavel Machek
commit 4bf9636c39ac70da091d5a2e28d3448eaa7f115c upstream. Commit 9fc2105aeaaf ("ARM: 7830/1: delay: don't bother reporting bogomips in /proc/cpuinfo") breaks audio in python, and probably elsewhere, with message FATAL: cannot locate cpu MHz in /proc/cpuinfo I'm not the first one to hit it, see for example https://theredblacktree.wordpress.com/2014/08/10/fatal-cannot-locate-cpu-mhz-in-proccpuinfo/ https://devtalk.nvidia.com/default/topic/765800/workaround-for-fatal-cannot-locate-cpu-mhz-in-proc-cpuinf/?offset=1 Reading original changelog, I have to say "Stop breaking working setups. You know who you are!". Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ARM: OMAP4: PM: Only do static dependency configuration in ↵Nishanth Menon
omap4_init_static_deps commit 9008d83fe9dc2e0f19b8ba17a423b3759d8e0fd7 upstream. Commit 705814b5ea6f ("ARM: OMAP4+: PM: Consolidate OMAP4 PM code to re-use it for OMAP5") Moved logic generic for OMAP5+ as part of the init routine by introducing omap4_pm_init. However, the patch left the powerdomain initial setup, an unused omap4430 es1.0 check and a spurious log "Power Management for TI OMAP4." in the original code. Remove the duplicate code which is already present in omap4_pm_init from omap4_init_static_deps. As part of this change, also move the u-boot version print out of the static dependency function to the omap4_pm_init function. Fixes: 705814b5ea6f ("ARM: OMAP4+: PM: Consolidate OMAP4 PM code to re-use it for OMAP5") Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ARM: dts: Enable PWM node by default for s3c64xxTomasz Figa
commit 5e794de514f56de1e78e979ca09c56a91aa2e9f1 upstream. The PWM block is required for system clock source so it must be always enabled. This patch fixes boot issues on SMDK6410 which did not have the node enabled explicitly for other purposes. Fixes: eeb93d02 ("clocksource: of: Respect device tree node status") Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ARM: dts: DRA7: wdt: Fix compatible property for watchdog nodeLokesh Vutla
commit be6688350a4470e417aaeca54d162652aab40ac5 upstream. OMAP wdt driver supports only ti,omap3-wdt compatible. In DRA7 dt wdt compatible property is defined as ti,omap4-wdt by mistake instead of ti,omap3-wdt. Correcting the typo. Fixes: 6e58b8f1daaf1a ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board") Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16sched/deadline: Avoid double-accounting in case of missed deadlinesLuca Abeni
commit 269ad8015a6b2bb1cf9e684da4921eb6fa0a0c88 upstream. The dl_runtime_exceeded() function is supposed to ckeck if a SCHED_DEADLINE task must be throttled, by checking if its current runtime is <= 0. However, it also checks if the scheduling deadline has been missed (the current time is larger than the current scheduling deadline), further decreasing the runtime if this happens. This "double accounting" is wrong: - In case of partitioned scheduling (or single CPU), this happens if task_tick_dl() has been called later than expected (due to small HZ values). In this case, the current runtime is also negative, and replenish_dl_entity() can take care of the deadline miss by recharging the current runtime to a value smaller than dl_runtime - In case of global scheduling on multiple CPUs, scheduling deadlines can be missed even if the task did not consume more runtime than expected, hence penalizing the task is wrong This patch fix this problem by throttling a SCHED_DEADLINE task only when its runtime becomes negative, and not modifying the runtime Signed-off-by: Luca Abeni <luca.abeni@unitn.it> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Juri Lelli <juri.lelli@gmail.com> Cc: Dario Faggioli <raistlin@linux.it> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1418813432-20797-3-git-send-email-luca.abeni@unitn.it Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16sched/deadline: Fix migration of SCHED_DEADLINE tasksLuca Abeni
commit 6a503c3be937d275113b702e0421e5b0720abe8a upstream. According to global EDF, tasks should be migrated between runqueues without checking if their scheduling deadlines and runtimes are valid. However, SCHED_DEADLINE currently performs such a check: a migration happens doing: deactivate_task(rq, next_task, 0); set_task_cpu(next_task, later_rq->cpu); activate_task(later_rq, next_task, 0); which ends up calling dequeue_task_dl(), setting the new CPU, and then calling enqueue_task_dl(). enqueue_task_dl() then calls enqueue_dl_entity(), which calls update_dl_entity(), which can modify scheduling deadline and runtime, breaking global EDF scheduling. As a result, some of the properties of global EDF are not respected: for example, a taskset {(30, 80), (40, 80), (120, 170)} scheduled on two cores can have unbounded response times for the third task even if 30/80+40/80+120/170 = 1.5809 < 2 This can be fixed by invoking update_dl_entity() only in case of wakeup, or if this is a new SCHED_DEADLINE task. Signed-off-by: Luca Abeni <luca.abeni@unitn.it> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Juri Lelli <juri.lelli@gmail.com> Cc: Dario Faggioli <raistlin@linux.it> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1418813432-20797-2-git-send-email-luca.abeni@unitn.it Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16scripts/kernel-doc: don't eat struct members with __alignedJohannes Berg
commit 7b990789a4c3420fa57596b368733158e432d444 upstream. The change from \d+ to .+ inside __aligned() means that the following structure: struct test { u8 a __aligned(2); u8 b __aligned(2); }; essentially gets modified to struct test { u8 a; }; for purposes of kernel-doc, thus dropping a struct member, which in turns causes warnings and invalid kernel-doc generation. Fix this by replacing the catch-all (".") with anything that's not a semicolon ("[^;]"). Fixes: 9dc30918b23f ("scripts/kernel-doc: handle struct member __aligned without numbers") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: Nishanth Menon <nm@ti.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() racesRyusuke Konishi
commit 705304a863cc41585508c0f476f6d3ec28cf7e00 upstream. Same story as in commit 41080b5a2401 ("nfsd race fixes: ext2") (similar ext2 fix) except that nilfs2 needs to use insert_inode_locked4() instead of insert_inode_locked() and a bug of a check for dead inodes needs to be fixed. If nilfs_iget() is called from nfsd after nilfs_new_inode() calls insert_inode_locked4(), nilfs_iget() will wait for unlock_new_inode() at the end of nilfs_mkdir()/nilfs_create()/etc to unlock the inode. If nilfs_iget() is called before nilfs_new_inode() calls insert_inode_locked4(), it will create an in-core inode and read its data from the on-disk inode. But, nilfs_iget() will find i_nlink equals zero and fail at nilfs_read_inode_common(), which will lead it to call iget_failed() and cleanly fail. However, this sanity check doesn't work as expected for reused on-disk inodes because they leave a non-zero value in i_mode field and it hinders the test of i_nlink. This patch also fixes the issue by removing the test on i_mode that nilfs2 doesn't need. Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16mtd: tests: abort torturetest on erase errorsBrian Norris
commit 68f29815034e9dc9ed53cad85946c32b07adc8cc upstream. The torture test should quit once it actually induces an error in the flash. This step was accidentally removed during refactoring. Without this fix, the torturetest just continues infinitely, or until the maximum cycle count is reached. e.g.: ... [ 7619.218171] mtd_test: error -5 while erasing EB 100 [ 7619.297981] mtd_test: error -5 while erasing EB 100 [ 7619.377953] mtd_test: error -5 while erasing EB 100 [ 7619.457998] mtd_test: error -5 while erasing EB 100 [ 7619.537990] mtd_test: error -5 while erasing EB 100 ... Fixes: 6cf78358c94f ("mtd: mtd_torturetest: use mtd_test helpers") Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ceph: fix null pointer dereference in discard_cap_releases()Yan, Zheng
commit 00bd8edb861eb41d274938cfc0338999d9c593a3 upstream. send_mds_reconnect() may call discard_cap_releases() after all release messages have been dropped by cleanup_cap_releases() Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com> Reviewed-by: Sage Weil <sage@inktank.com> Cc: Markus Blank-Burian <burian@muenster.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ceph: do_sync is never initializedDan Carpenter
commit 021b77bee210843bed1ea91b5cad58235ff9c8e5 upstream. Probably this code was syncing a lot more often then intended because the do_sync variable wasn't set to zero. Fixes: c62988ec0910 ('ceph: avoid meaningless calling ceph_caps_revoking if sync_mode == WB_SYNC_ALL.') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Ilya Dryomov <idryomov@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16nfsd4: fix xdr4 inclusion of escaped charBenjamin Coddington
commit 5a64e56976f1ba98743e1678c0029a98e9034c81 upstream. Fix a bug where nfsd4_encode_components_esc() includes the esc_end char as an additional string encoding. Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Fixes: e7a0444aef4a "nfsd: add IPv6 addr escaping to fs_location hosts" Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16fs: nfsd: Fix signedness bug in compare_blobRasmus Villemoes
commit ef17af2a817db97d42dd2ec0a425231748e23dbc upstream. Bugs similar to the one in acbbe6fbb240 (kcmp: fix standard comparison bug) are in rich supply. In this variant, the problem is that struct xdr_netobj::len has type unsigned int, so the expression o1->len - o2->len _also_ has type unsigned int; it has completely well-defined semantics, and the result is some non-negative integer, which is always representable in a long long. But this means that if the conditional triggers, we are guaranteed to return a positive value from compare_blob. In this case it could be fixed by - res = o1->len - o2->len; + res = (long long)o1->len - (long long)o2->len; but I'd rather eliminate the usually broken 'return a - b;' idiom. Reviewed-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16Drivers: hv: vmbus: Fix a race condition when unregistering a deviceVitaly Kuznetsov
commit 04a258c162a85c0f4ae56be67634dc43c9a4fa9b upstream. When build with Debug the following crash is sometimes observed: Call Trace: [<ffffffff812b9600>] string+0x40/0x100 [<ffffffff812bb038>] vsnprintf+0x218/0x5e0 [<ffffffff810baf7d>] ? trace_hardirqs_off+0xd/0x10 [<ffffffff812bb4c1>] vscnprintf+0x11/0x30 [<ffffffff8107a2f0>] vprintk+0xd0/0x5c0 [<ffffffffa0051ea0>] ? vmbus_process_rescind_offer+0x0/0x110 [hv_vmbus] [<ffffffff8155c71c>] printk+0x41/0x45 [<ffffffffa004ebac>] vmbus_device_unregister+0x2c/0x40 [hv_vmbus] [<ffffffffa0051ecb>] vmbus_process_rescind_offer+0x2b/0x110 [hv_vmbus] ... This happens due to the following race: between 'if (channel->device_obj)' check in vmbus_process_rescind_offer() and pr_debug() in vmbus_device_unregister() the device can disappear. Fix the issue by taking an additional reference to the device before proceeding to vmbus_device_unregister(). Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16n_tty: Fix read_buf race condition, increment read_head after pushing dataChristian Riesch
commit 8bfbe2de769afda051c56aba5450391670e769fc upstream. Commit 19e2ad6a09f0c06dbca19c98e5f4584269d913dd ("n_tty: Remove overflow tests from receive_buf() path") moved the increment of read_head into the arguments list of read_buf_addr(). Function calls represent a sequence point in C. Therefore read_head is incremented before the character c is placed in the buffer. Since the circular read buffer is a lock-less design since commit 6d76bd2618535c581f1673047b8341fd291abc67 ("n_tty: Make N_TTY ldisc receive path lockless"), this creates a race condition that leads to communication errors. This patch modifies the code to increment read_head _after_ the data is placed in the buffer and thus fixes the race for non-SMP machines. To fix the problem for SMP machines, memory barriers must be added in a separate patch. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16serial: samsung: wait for transfer completion before clock disableRobert Baldyga
commit 1ff383a4c3eda8893ec61b02831826e1b1f46b41 upstream. This patch adds waiting until transmit buffer and shifter will be empty before clock disabling. Without this fix it's possible to have clock disabled while data was not transmited yet, which causes unproper state of TX line and problems in following data transfers. Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16tracing/sched: Check preempt_count() for current when reading task->stateSteven Rostedt (Red Hat)
commit aee4e5f3d3abb7a2239dd02f6d8fb173413fd02f upstream. When recording the state of a task for the sched_switch tracepoint a check of task_preempt_count() is performed to see if PREEMPT_ACTIVE is set. This is because, technically, a task being preempted is really in the TASK_RUNNING state, and that is what should be recorded when tracing a sched_switch, even if the task put itself into another state (it hasn't scheduled out in that state yet). But with the change to use per_cpu preempt counts, the task_thread_info(p)->preempt_count is no longer used, and instead task_preempt_count(p) is used. The problem is that this does not use the current preempt count but a stale one from a previous sched_switch. The task_preempt_count(p) uses saved_preempt_count and not preempt_count(). But for tracing sched_switch, if p is current, we really want preempt_count(). I hit this bug when I was tracing sleep and the call from do_nanosleep() scheduled out in the "RUNNING" state. sleep-4290 [000] 537272.259992: sched_switch: sleep:4290 [120] R ==> swapper/0:0 [120] sleep-4290 [000] 537272.260015: kernel_stack: <stack trace> => __schedule (ffffffff8150864a) => schedule (ffffffff815089f8) => do_nanosleep (ffffffff8150b76c) => hrtimer_nanosleep (ffffffff8108d66b) => SyS_nanosleep (ffffffff8108d750) => return_to_handler (ffffffff8150e8e5) => tracesys_phase2 (ffffffff8150c844) After a bit of hair pulling, I found that the state was really TASK_INTERRUPTIBLE, but the saved_preempt_count had an old PREEMPT_ACTIVE set and caused the sched_switch tracepoint to show it as RUNNING. Link: http://lkml.kernel.org/r/20141210174428.3cb7542a@gandalf.local.home Acked-by: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 01028747559a "sched: Create more preempt_count accessors" Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16writeback: fix a subtle race condition in I_DIRTY clearingTejun Heo
commit 9c6ac78eb3521c5937b2dd8a7d1b300f41092f45 upstream. After invoking ->dirty_inode(), __mark_inode_dirty() does smp_mb() and tests inode->i_state locklessly to see whether it already has all the necessary I_DIRTY bits set. The comment above the barrier doesn't contain any useful information - memory barriers can't ensure "changes are seen by all cpus" by itself. And it sure enough was broken. Please consider the following scenario. CPU 0 CPU 1 ------------------------------------------------------------------------------- enters __writeback_single_inode() grabs inode->i_lock tests PAGECACHE_TAG_DIRTY which is clear enters __set_page_dirty() grabs mapping->tree_lock sets PAGECACHE_TAG_DIRTY releases mapping->tree_lock leaves __set_page_dirty() enters __mark_inode_dirty() smp_mb() sees I_DIRTY_PAGES set leaves __mark_inode_dirty() clears I_DIRTY_PAGES releases inode->i_lock Now @inode has dirty pages w/ I_DIRTY_PAGES clear. This doesn't seem to lead to an immediately critical problem because requeue_inode() later checks PAGECACHE_TAG_DIRTY instead of I_DIRTY_PAGES when deciding whether the inode needs to be requeued for IO and there are enough unintentional memory barriers inbetween, so while the inode ends up with inconsistent I_DIRTY_PAGES flag, it doesn't fall off the IO list. The lack of explicit barrier may also theoretically affect the other I_DIRTY bits which deal with metadata dirtiness. There is no guarantee that a strong enough barrier exists between I_DIRTY_[DATA]SYNC clearing and write_inode() writing out the dirtied inode. Filesystem inode writeout path likely has enough stuff which can behave as full barrier but it's theoretically possible that the writeout may not see all the updates from ->dirty_inode(). Fix it by adding an explicit smp_mb() after I_DIRTY clearing. Note that I_DIRTY_PAGES needs a special treatment as it always needs to be cleared to be interlocked with the lockless test on __mark_inode_dirty() side. It's cleared unconditionally and reinstated after smp_mb() if the mapping still has dirty pages. Also add comments explaining how and why the barriers are paired. Lightly tested. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jan Kara <jack@suse.cz> Cc: Mikulas Patocka <mpatocka@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16cdc-acm: memory leak in error caseOliver Neukum
commit d908f8478a8d18e66c80a12adb27764920c1f1ca upstream. If probe() fails not only the attributes need to be removed but also the memory freed. Reported-by: Ahmed Tamrawi <ahmedtamrawi@gmail.com> Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16genhd: check for int overflow in disk_expand_part_tbl()Jens Axboe
commit 5fabcb4c33fe11c7e3afdf805fde26c1a54d0953 upstream. We can get here from blkdev_ioctl() -> blkpg_ioctl() -> add_partition() with a user passed in partno value. If we pass in 0x7fffffff, the new target in disk_expand_part_tbl() overflows the 'int' and we access beyond the end of ptbl->part[] and even write to it when we do the rcu_assign_pointer() to assign the new partition. Reported-by: David Ramos <daramos@stanford.edu> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16Add USB_EHCI_EXYNOS to multi_v7_defconfigSteev Klimaszewski
commit 007487f1fd43d84f26cda926081ca219a24ecbc4 upstream. Currently we enable Exynos devices in the multi v7 defconfig, however, when testing on my ODROID-U3, I noticed that USB was not working. Enabling this option causes USB to work, which enables networking support as well since the ODROID-U3 has networking on the USB bus. [arnd] Support for odroid-u3 was added in 3.10, so it would be nice to backport this fix at least that far. Signed-off-by: Steev Klimaszewski <steev@gentoo.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16USB: cdc-acm: check for valid interfacesGreg Kroah-Hartman
commit 403dff4e2c94f275e24fd85f40b2732ffec268a1 upstream. We need to check that we have both a valid data and control inteface for both types of headers (union and not union.) References: https://bugzilla.kernel.org/show_bug.cgi?id=83551 Reported-by: Simon Schubert <2+kernel@0x2c.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ALSA: hda - Fix wrong gpio_dir & gpio_mask hint setups for IDT/STAC codecsTakashi Iwai
commit c507de88f6a336bd7296c9ec0073b2d4af8b4f5e upstream. stac_store_hints() does utterly wrong for masking the values for gpio_dir and gpio_data, likely due to copy&paste errors. Fortunately, this feature is used very rarely, so the impact must be really small. Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ALSA: hda - using uninitialized dataDan Carpenter
commit 69eba10e606a80665f8573221fec589430d9d1cb upstream. In olden times the snd_hda_param_read() function always set "*start_id" but in 2007 we introduced a new return and it causes uninitialized data bugs in a couple of the callers: print_codec_info() and hdmi_parse_codec(). Fixes: e8a7f136f5ed ('[ALSA] hda-intel - Improve HD-audio codec probing robustness') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16ALSA: usb-audio: extend KEF X300A FU 10 tweak to Arcam rPACJiri Jaburek
commit d70a1b9893f820fdbcdffac408c909c50f2e6b43 upstream. The Arcam rPAC seems to have the same problem - whenever anything (alsamixer, udevd, 3.9+ kernel from 60af3d037eb8c, ..) attempts to access mixer / control interface of the card, the firmware "locks up" the entire device, resulting in SNDRV_PCM_IOCTL_HW_PARAMS failed (-5): Input/output error from alsa-lib. Other operating systems can somehow read the mixer (there seems to be playback volume/mute), but any manipulation is ignored by the device (which has hardware volume controls). Signed-off-by: Jiri Jaburek <jjaburek@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16misc: genwqe: check for error from get_user_pages_fast()Ian Abbott
commit cf35d6e0475982667b0d2d318fb27be4b8849827 upstream. `genwqe_user_vmap()` calls `get_user_pages_fast()` and if the return value is less than the number of pages requested, it frees the pages and returns an error (`-EFAULT`). However, it fails to consider a negative error return value from `get_user_pages_fast()`. In that case, the test `if (rc < m->nr_pages)` will be false (due to promotion of `rc` to a large `unsigned int`) and the code will continue on to call `genwqe_map_pages()` with an invalid list of page pointers. Fix it by bailing out if `get_user_pages_fast()` returns a negative error value. Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16driver core: Fix unbalanced device reference in drivers_probeAlex Williamson
commit bb34cb6bbd287b57e955bc5cfd42fcde6aaca279 upstream. bus_find_device_by_name() acquires a device reference which is never released. This results in an object leak, which on older kernels results in failure to release all resources of PCI devices. libvirt uses drivers_probe to re-attach devices to the host after assignment and is therefore a common trigger for this leak. Example: # cd /sys/bus/pci/ # dmesg -C # echo 1 > devices/0000\:01\:00.0/sriov_numvfs # echo 0 > devices/0000\:01\:00.0/sriov_numvfs # dmesg | grep 01:10 pci 0000:01:10.0: [8086:10ca] type 00 class 0x020000 kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_add_internal: parent: '0000:00:01.0', set: 'devices' kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79cd0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79cd0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79cd0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_cleanup, parent (null) kobject: '0000:01:10.0' (ffff8801d79cd0a8): calling ktype release kobject: '0000:01:10.0': free name [kobject freed as expected] # dmesg -C # echo 1 > devices/0000\:01\:00.0/sriov_numvfs # echo 0000:01:10.0 > drivers_probe # echo 0 > devices/0000\:01\:00.0/sriov_numvfs # dmesg | grep 01:10 pci 0000:01:10.0: [8086:10ca] type 00 class 0x020000 kobject: '0000:01:10.0' (ffff8801d79ce0a8): kobject_add_internal: parent: '0000:00:01.0', set: 'devices' kobject: '0000:01:10.0' (ffff8801d79ce0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79ce0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79ce0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79ce0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79ce0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79ce0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' [no free] Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16x86, vdso: Use asm volatile in __getcpuAndy Lutomirski
commit 1ddf0b1b11aa8a90cef6706e935fc31c75c406ba upstream. In Linux 3.18 and below, GCC hoists the lsl instructions in the pvclock code all the way to the beginning of __vdso_clock_gettime, slowing the non-paravirt case significantly. For unknown reasons, presumably related to the removal of a branch, the performance issue is gone as of e76b027e6408 x86,vdso: Use LSL unconditionally for vgetcpu but I don't trust GCC enough to expect the problem to stay fixed. There should be no correctness issue, because the __getcpu calls in __vdso_vlock_gettime were never necessary in the first place. Note to stable maintainers: In 3.18 and below, depending on configuration, gcc 4.9.2 generates code like this: 9c3: 44 0f 03 e8 lsl %ax,%r13d 9c7: 45 89 eb mov %r13d,%r11d 9ca: 0f 03 d8 lsl %ax,%ebx This patch won't apply as is to any released kernel, but I'll send a trivial backported version if needed. [ Backported by Andy Lutomirski. Should apply to all affected versions. This fixes a functionality bug as well as a performance bug: buggy kernels can infinite loop in __vdso_clock_gettime on affected compilers. See, for exammple: https://bugzilla.redhat.com/show_bug.cgi?id=1178975 ] Fixes: 51c19b4f5927 x86: vdso: pvclock gettime support Cc: Marcelo Tosatti <mtosatti@redhat.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16x86_64, vdso: Fix the vdso address randomization algorithmAndy Lutomirski
commit 394f56fe480140877304d342dec46d50dc823d46 upstream. The theory behind vdso randomization is that it's mapped at a random offset above the top of the stack. To avoid wasting a page of memory for an extra page table, the vdso isn't supposed to extend past the lowest PMD into which it can fit. Other than that, the address should be a uniformly distributed address that meets all of the alignment requirements. The current algorithm is buggy: the vdso has about a 50% probability of being at the very end of a PMD. The current algorithm also has a decent chance of failing outright due to incorrect handling of the case where the top of the stack is near the top of its PMD. This fixes the implementation. The paxtest estimate of vdso "randomisation" improves from 11 bits to 18 bits. (Disclaimer: I don't know what the paxtest code is actually calculating.) It's worth noting that this algorithm is inherently biased: the vdso is more likely to end up near the end of its PMD than near the beginning. Ideally we would either nix the PMD sharing requirement or jointly randomize the vdso and the stack to reduce the bias. In the mean time, this is a considerable improvement with basically no risk of compatibility issues, since the allowed outputs of the algorithm are unchanged. As an easy test, doing this: for i in `seq 10000` do grep -P vdso /proc/self/maps |cut -d- -f1 done |sort |uniq -d used to produce lots of output (1445 lines on my most recent run). A tiny subset looks like this: 7fffdfffe000 7fffe01fe000 7fffe05fe000 7fffe07fe000 7fffe09fe000 7fffe0bfe000 7fffe0dfe000 Note the suspicious fe000 endings. With the fix, I get a much more palatable 76 repeated addresses. Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-16kvm: x86: drop severity of "generation wraparound" messagePaolo Bonzini
commit a629df7eadffb03e6ce4a8616e62ea29fdf69b6b upstream. Since most virtual machines raise this message once, it is a bit annoying. Make it KERN_DEBUG severity. Fixes: 7a2e8aaf0f6873b47bc2347f216ea5b0e4c258ab Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>