diff options
Diffstat (limited to 'drivers/net/usb')
| -rw-r--r-- | drivers/net/usb/Kconfig | 10 | ||||
| -rw-r--r-- | drivers/net/usb/Makefile | 2 | ||||
| -rw-r--r-- | drivers/net/usb/cdc_ncm.c | 6 |
3 files changed, 14 insertions, 4 deletions
diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig index 1f6893ebce16..3a7286256db0 100644 --- a/drivers/net/usb/Kconfig +++ b/drivers/net/usb/Kconfig @@ -395,6 +395,10 @@ config USB_NET_RNDIS_HOST The protocol specification is incomplete, and is controlled by (and for) Microsoft; it isn't an "Open" ecosystem or market. +config USB_NET_CDC_SUBSET_ENABLE + tristate + depends on USB_NET_CDC_SUBSET + config USB_NET_CDC_SUBSET tristate "Simple USB Network Links (CDC Ethernet subset)" depends on USB_USBNET @@ -413,6 +417,7 @@ config USB_NET_CDC_SUBSET config USB_ALI_M5632 bool "ALi M5632 based 'USB 2.0 Data Link' cables" depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE help Choose this option if you're using a host-to-host cable based on this design, which supports USB 2.0 high speed. @@ -420,6 +425,7 @@ config USB_ALI_M5632 config USB_AN2720 bool "AnchorChips 2720 based cables (Xircom PGUNET, ...)" depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE help Choose this option if you're using a host-to-host cable based on this design. Note that AnchorChips is now a @@ -428,6 +434,7 @@ config USB_AN2720 config USB_BELKIN bool "eTEK based host-to-host cables (Advance, Belkin, ...)" depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE default y help Choose this option if you're using a host-to-host cable @@ -437,6 +444,7 @@ config USB_BELKIN config USB_ARMLINUX bool "Embedded ARM Linux links (iPaq, ...)" depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE default y help Choose this option to support the "usb-eth" networking driver @@ -454,6 +462,7 @@ config USB_ARMLINUX config USB_EPSON2888 bool "Epson 2888 based firmware (DEVELOPMENT)" depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE help Choose this option to support the usb networking links used by some sample firmware from Epson. @@ -461,6 +470,7 @@ config USB_EPSON2888 config USB_KC2190 bool "KT Technology KC2190 based cables (InstaNet)" depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE help Choose this option if you're using a host-to-host cable with one of these chips. diff --git a/drivers/net/usb/Makefile b/drivers/net/usb/Makefile index b5f04068dbe4..37fb46aee341 100644 --- a/drivers/net/usb/Makefile +++ b/drivers/net/usb/Makefile @@ -23,7 +23,7 @@ obj-$(CONFIG_USB_NET_GL620A) += gl620a.o obj-$(CONFIG_USB_NET_NET1080) += net1080.o obj-$(CONFIG_USB_NET_PLUSB) += plusb.o obj-$(CONFIG_USB_NET_RNDIS_HOST) += rndis_host.o -obj-$(CONFIG_USB_NET_CDC_SUBSET) += cdc_subset.o +obj-$(CONFIG_USB_NET_CDC_SUBSET_ENABLE) += cdc_subset.o obj-$(CONFIG_USB_NET_ZAURUS) += zaurus.o obj-$(CONFIG_USB_NET_MCS7830) += mcs7830.o obj-$(CONFIG_USB_USBNET) += usbnet.o diff --git a/drivers/net/usb/cdc_ncm.c b/drivers/net/usb/cdc_ncm.c index 1228d0da4075..72cb30828a12 100644 --- a/drivers/net/usb/cdc_ncm.c +++ b/drivers/net/usb/cdc_ncm.c @@ -825,6 +825,9 @@ int cdc_ncm_bind_common(struct usbnet *dev, struct usb_interface *intf, u8 data_ goto error2; } + /* Device-specific flags */ + ctx->drvflags = drvflags; + /* * Some Huawei devices have been observed to come out of reset in NDP32 mode. * Let's check if this is the case, and set the device to NDP16 mode again if @@ -873,9 +876,6 @@ int cdc_ncm_bind_common(struct usbnet *dev, struct usb_interface *intf, u8 data_ /* finish setting up the device specific data */ cdc_ncm_setup(dev); - /* Device-specific flags */ - ctx->drvflags = drvflags; - /* Allocate the delayed NDP if needed. */ if (ctx->drvflags & CDC_NCM_FLAG_NDP_TO_END) { ctx->delayed_ndp16 = kzalloc(ctx->max_ndp_size, GFP_KERNEL); |