diff options
Diffstat (limited to 'drivers/net/tulip/Kconfig')
| -rw-r--r-- | drivers/net/tulip/Kconfig | 171 |
1 files changed, 0 insertions, 171 deletions
diff --git a/drivers/net/tulip/Kconfig b/drivers/net/tulip/Kconfig deleted file mode 100644 index 1f8d4a8d8ea4..000000000000 --- a/drivers/net/tulip/Kconfig +++ /dev/null @@ -1,171 +0,0 @@ -# -# Tulip family network device configuration -# - -menuconfig NET_TULIP - bool "\"Tulip\" family network device support" - depends on PCI || EISA || CARDBUS - help - This selects the "Tulip" family of EISA/PCI network cards. - -if NET_TULIP - -config DE2104X - tristate "Early DECchip Tulip (dc2104x) PCI support" - depends on PCI - select CRC32 - ---help--- - This driver is developed for the SMC EtherPower series Ethernet - cards and also works with cards based on the DECchip - 21040 (Tulip series) chips. Some LinkSys PCI cards are - of this type. (If your card is NOT SMC EtherPower 10/100 PCI - (smc9332dst), you can also try the driver for "Generic DECchip" - cards, below. However, most people with a network card of this type - will say Y here.) Do read the Ethernet-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. - - To compile this driver as a module, choose M here. The module will - be called de2104x. - -config DE2104X_DSL - int "Descriptor Skip Length in 32 bit longwords" - depends on DE2104X - range 0 31 - default 0 - help - Setting this value allows to align ring buffer descriptors into their - own cache lines. Value of 4 corresponds to the typical 32 byte line - (the descriptor is 16 bytes). This is necessary on systems that lack - cache coherence, an example is PowerMac 5500. Otherwise 0 is safe. - Default is 0, and range is 0 to 31. - -config TULIP - tristate "DECchip Tulip (dc2114x) PCI support" - depends on PCI - select CRC32 - ---help--- - This driver is developed for the SMC EtherPower series Ethernet - cards and also works with cards based on the DECchip - 21140 (Tulip series) chips. Some LinkSys PCI cards are - of this type. (If your card is NOT SMC EtherPower 10/100 PCI - (smc9332dst), you can also try the driver for "Generic DECchip" - cards, above. However, most people with a network card of this type - will say Y here.) Do read the Ethernet-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. - - To compile this driver as a module, choose M here. The module will - be called tulip. - -config TULIP_MWI - bool "New bus configuration (EXPERIMENTAL)" - depends on TULIP && EXPERIMENTAL - help - This configures your Tulip card specifically for the card and - system cache line size type you are using. - - This is experimental code, not yet tested on many boards. - - If unsure, say N. - -config TULIP_MMIO - bool "Use PCI shared mem for NIC registers" - depends on TULIP - help - Use PCI shared memory for the NIC registers, rather than going through - the Tulip's PIO (programmed I/O ports). Faster, but could produce - obscure bugs if your mainboard has memory controller timing issues. - If in doubt, say N. - -config TULIP_NAPI - bool "Use RX polling (NAPI)" - depends on TULIP - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - -config TULIP_NAPI_HW_MITIGATION - bool "Use Interrupt Mitigation" - depends on TULIP_NAPI - ---help--- - Use HW to reduce RX interrupts. Not strictly necessary since NAPI - reduces RX interrupts by itself. Interrupt mitigation reduces RX - interrupts even at low levels of traffic at the cost of a small - latency. - - If in doubt, say Y. - -config TULIP_DM910X - def_bool y - depends on TULIP && SPARC - -config DE4X5 - tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA" - depends on PCI || EISA - select CRC32 - ---help--- - This is support for the DIGITAL series of PCI/EISA Ethernet cards. - These include the DE425, DE434, DE435, DE450 and DE500 models. If - you have a network card of this type, say Y and read the - Ethernet-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. More specific - information is contained in - <file:Documentation/networking/de4x5.txt>. - - To compile this driver as a module, choose M here. The module will - be called de4x5. - -config WINBOND_840 - tristate "Winbond W89c840 Ethernet support" - depends on PCI - select CRC32 - select MII - help - This driver is for the Winbond W89c840 chip. It also works with - the TX9882 chip on the Compex RL100-ATX board. - More specific information and updates are available from - <http://www.scyld.com/network/drivers.html>. - -config DM9102 - tristate "Davicom DM910x/DM980x support" - depends on PCI - select CRC32 - ---help--- - This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from - Davicom (<http://www.davicom.com.tw/>). If you have such a network - (Ethernet) card, say Y. Some information is contained in the file - <file:Documentation/networking/dmfe.txt>. - - To compile this driver as a module, choose M here. The module will - be called dmfe. - -config ULI526X - tristate "ULi M526x controller support" - depends on PCI - select CRC32 - ---help--- - This driver is for ULi M5261/M5263 10/100M Ethernet Controller - (<http://www.nvidia.com/page/uli_drivers.html>). - - To compile this driver as a module, choose M here. The module will - be called uli526x. - -config PCMCIA_XIRCOM - tristate "Xircom CardBus support" - depends on CARDBUS - ---help--- - This driver is for the Digital "Tulip" Ethernet CardBus adapters. - It should work with most DEC 21*4*-based chips/ethercards, as well - as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and - ASIX. - - To compile this driver as a module, choose M here. The module will - be called xircom_cb. If unsure, say N. - -endif # NET_TULIP |