diff options
Diffstat (limited to 'arch/blackfin/mach-bf548')
| -rw-r--r-- | arch/blackfin/mach-bf548/Kconfig | 8 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/boards/cm_bf548.c | 10 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/boards/ezkit.c | 109 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/include/mach/anomaly.h | 56 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/include/mach/blackfin.h | 1 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/include/mach/mem_map.h | 51 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/include/mach/portmux.h | 64 |
7 files changed, 216 insertions, 83 deletions
diff --git a/arch/blackfin/mach-bf548/Kconfig b/arch/blackfin/mach-bf548/Kconfig index dcf657159051..a09623dfd550 100644 --- a/arch/blackfin/mach-bf548/Kconfig +++ b/arch/blackfin/mach-bf548/Kconfig @@ -11,6 +11,13 @@ config DEB_DMA_URGENT help Treat any DEB1, DEB2 and DEB3 request as Urgent +config BF548_ATAPI_ALTERNATIVE_PORT + bool "BF548 ATAPI alternative port via GPIO" + help + BF548 ATAPI data and address PINs can be routed through + async address or GPIO port F and G. Select y to route it + to GPIO. + comment "Interrupt Priority Assignment" menu "Priority" @@ -250,6 +257,7 @@ config IRQ_OTPSEC default 11 config IRQ_TIMER0 int "IRQ_TIMER0" + default 7 if TICKSOURCE_GPTMR0 default 8 config IRQ_TIMER1 int "IRQ_TIMER1" diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c index f53ad682530b..f5a3c30a41bd 100644 --- a/arch/blackfin/mach-bf548/boards/cm_bf548.c +++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c @@ -612,6 +612,11 @@ static struct resource bfin_spi0_resource[] = { [1] = { .start = CH_SPI0, .end = CH_SPI0, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI0, + .end = IRQ_SPI0, .flags = IORESOURCE_IRQ, } }; @@ -626,6 +631,11 @@ static struct resource bfin_spi1_resource[] = { [1] = { .start = CH_SPI1, .end = CH_SPI1, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI1, + .end = IRQ_SPI1, .flags = IORESOURCE_IRQ, } }; diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c index 096e661700a7..81f5b95cc361 100644 --- a/arch/blackfin/mach-bf548/boards/ezkit.c +++ b/arch/blackfin/mach-bf548/boards/ezkit.c @@ -76,7 +76,6 @@ static struct resource bfin_isp1760_resources[] = { static struct isp1760_platform_data isp1760_priv = { .is_isp1761 = 0, - .port1_disable = 0, .bus_width_16 = 1, .port1_otg = 0, .analog_oc = 0, @@ -208,6 +207,43 @@ static struct platform_device bfin_rotary_device = { }; #endif +#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE) +#include <linux/input.h> +#include <linux/spi/adxl34x.h> +static const struct adxl34x_platform_data adxl34x_info = { + .x_axis_offset = 0, + .y_axis_offset = 0, + .z_axis_offset = 0, + .tap_threshold = 0x31, + .tap_duration = 0x10, + .tap_latency = 0x60, + .tap_window = 0xF0, + .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN, + .act_axis_control = 0xFF, + .activity_threshold = 5, + .inactivity_threshold = 3, + .inactivity_time = 4, + .free_fall_threshold = 0x7, + .free_fall_time = 0x20, + .data_rate = 0x8, + .data_range = ADXL_FULL_RES, + + .ev_type = EV_ABS, + .ev_code_x = ABS_X, /* EV_REL */ + .ev_code_y = ABS_Y, /* EV_REL */ + .ev_code_z = ABS_Z, /* EV_REL */ + + .ev_code_tap_x = BTN_TOUCH, /* EV_KEY */ + .ev_code_tap_y = BTN_TOUCH, /* EV_KEY */ + .ev_code_tap_z = BTN_TOUCH, /* EV_KEY */ + +/* .ev_code_ff = KEY_F,*/ /* EV_KEY */ +/* .ev_code_act_inactivity = KEY_A,*/ /* EV_KEY */ + .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK, + .fifo_mode = ADXL_FIFO_STREAM, +}; +#endif + #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) static struct platform_device rtc_device = { .name = "rtc-bfin", @@ -359,6 +395,8 @@ static struct platform_device bfin_sir3_device = { #endif #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#include <linux/smsc911x.h> + static struct resource smsc911x_resources[] = { { .name = "smsc911x-memory", @@ -372,11 +410,22 @@ static struct resource smsc911x_resources[] = { .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, }, }; + +static struct smsc911x_platform_config smsc911x_config = { + .flags = SMSC911X_USE_32BIT, + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, + .phy_interface = PHY_INTERFACE_MODE_MII, +}; + static struct platform_device smsc911x_device = { .name = "smsc911x", .id = 0, .num_resources = ARRAY_SIZE(smsc911x_resources), .resource = smsc911x_resources, + .dev = { + .platform_data = &smsc911x_config, + }, }; #endif @@ -628,6 +677,14 @@ static struct bfin5xx_spi_chip spidev_chip_info = { }; #endif +#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE) +static struct bfin5xx_spi_chip spi_adxl34x_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, + .cs_change_per_word = 0, +}; +#endif + static struct spi_board_info bfin_spi_board_info[] __initdata = { #if defined(CONFIG_MTD_M25P80) \ || defined(CONFIG_MTD_M25P80_MODULE) @@ -653,15 +710,15 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { }, #endif #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) -{ - .modalias = "ad7877", - .platform_data = &bfin_ad7877_ts_info, - .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */ - .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ - .bus_num = 0, - .chip_select = 2, - .controller_data = &spi_ad7877_chip_info, -}, + { + .modalias = "ad7877", + .platform_data = &bfin_ad7877_ts_info, + .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */ + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 2, + .controller_data = &spi_ad7877_chip_info, + }, #endif #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) { @@ -672,8 +729,19 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { .controller_data = &spidev_chip_info, }, #endif +#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE) + { + .modalias = "adxl34x", + .platform_data = &adxl34x_info, + .irq = IRQ_PC5, + .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = 2, + .controller_data = &spi_adxl34x_chip_info, + .mode = SPI_MODE_3, + }, +#endif }; - #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) /* SPI (0) */ static struct resource bfin_spi0_resource[] = { @@ -685,6 +753,11 @@ static struct resource bfin_spi0_resource[] = { [1] = { .start = CH_SPI0, .end = CH_SPI0, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI0, + .end = IRQ_SPI0, .flags = IORESOURCE_IRQ, } }; @@ -699,6 +772,11 @@ static struct resource bfin_spi1_resource[] = { [1] = { .start = CH_SPI1, .end = CH_SPI1, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI1, + .end = IRQ_SPI1, .flags = IORESOURCE_IRQ, } }; @@ -786,7 +864,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info0[] = { #if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */ static struct i2c_board_info __initdata bfin_i2c_board_info1[] = { -#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE) +#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE) { I2C_BOARD_INFO("pcf8574_lcd", 0x22), }, @@ -797,6 +875,13 @@ static struct i2c_board_info __initdata bfin_i2c_board_info1[] = { .irq = 212, }, #endif +#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE) + { + I2C_BOARD_INFO("adxl34x", 0x53), + .irq = IRQ_PC5, + .platform_data = (void *)&adxl34x_info, + }, +#endif }; #endif diff --git a/arch/blackfin/mach-bf548/include/mach/anomaly.h b/arch/blackfin/mach-bf548/include/mach/anomaly.h index 882e40ccf0d1..18a4cd24f673 100644 --- a/arch/blackfin/mach-bf548/include/mach/anomaly.h +++ b/arch/blackfin/mach-bf548/include/mach/anomaly.h @@ -6,36 +6,41 @@ * Licensed under the GPL-2 or later. */ -/* This file shoule be up to date with: +/* This file should be up to date with: * - Revision H, 01/16/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List */ #ifndef _MACH_ANOMALY_H_ #define _MACH_ANOMALY_H_ +/* We do not support 0.0 or 0.1 silicon - sorry */ +#if __SILICON_REVISION__ < 2 +# error will not work on BF548 silicon version 0.0, or 0.1 +#endif + /* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot2 Not Supported */ #define ANOMALY_05000074 (1) /* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */ #define ANOMALY_05000119 (1) /* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */ #define ANOMALY_05000122 (1) -/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */ +/* False Hardware Error from an Access in the Shadow of a Conditional Branch */ #define ANOMALY_05000245 (1) /* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */ #define ANOMALY_05000265 (1) /* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */ #define ANOMALY_05000272 (1) -/* False Hardware Error Exception when ISR context is not restored */ +/* False Hardware Error Exception when ISR Context Is Not Restored */ #define ANOMALY_05000281 (__SILICON_REVISION__ < 1) /* SSYNCs After Writes To CAN/DMA MMR Registers Are Not Always Handled Correctly */ #define ANOMALY_05000304 (__SILICON_REVISION__ < 1) /* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */ #define ANOMALY_05000310 (1) -/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */ +/* Errors when SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */ #define ANOMALY_05000312 (__SILICON_REVISION__ < 1) /* TWI Slave Boot Mode Is Not Functional */ #define ANOMALY_05000324 (__SILICON_REVISION__ < 1) -/* External FIFO Boot Mode Is Not Functional */ +/* FIFO Boot Mode Not Functional */ #define ANOMALY_05000325 (__SILICON_REVISION__ < 2) /* Data Lost When Core and DMA Accesses Are Made to the USB FIFO Simultaneously */ #define ANOMALY_05000327 (__SILICON_REVISION__ < 1) @@ -59,7 +64,7 @@ #define ANOMALY_05000340 (__SILICON_REVISION__ < 1) /* Boot Host Wait (HWAIT) and Boot Host Wait Alternate (HWAITA) Signals Are Swapped */ #define ANOMALY_05000344 (__SILICON_REVISION__ < 1) -/* USB Calibration Value Is Not Intialized */ +/* USB Calibration Value Is Not Initialized */ #define ANOMALY_05000346 (__SILICON_REVISION__ < 1) /* USB Calibration Value to use */ #define ANOMALY_05000346_value 0x5411 @@ -147,11 +152,11 @@ #define ANOMALY_05000416 (1) /* Multichannel SPORT Channel Misalignment Under Specific Configuration */ #define ANOMALY_05000425 (1) -/* Speculative Fetches of Indirect-Pointer Instructions Can Cause Spurious Hardware Errors */ +/* Speculative Fetches of Indirect-Pointer Instructions Can Cause False Hardware Errors */ #define ANOMALY_05000426 (1) /* CORE_EPPI_PRIO bit and SYS_EPPI_PRIO bit in the HMDMA1_CONTROL register are not functional */ #define ANOMALY_05000427 (__SILICON_REVISION__ < 2) -/* WB_EDGE Bit in NFC_IRQSTAT Incorrectly Behaves as a Buffer Status Bit Instead of an IRQ Status Bit */ +/* WB_EDGE Bit in NFC_IRQSTAT Incorrectly Reflects Buffer Status Instead of IRQ Status */ #define ANOMALY_05000429 (__SILICON_REVISION__ < 2) /* Software System Reset Corrupts PLL_LOCKCNT Register */ #define ANOMALY_05000430 (__SILICON_REVISION__ >= 2) @@ -170,26 +175,59 @@ /* Reduced Timing Margins on DDR Output Setup and Hold (tDS and tDH) */ #define ANOMALY_05000449 (__SILICON_REVISION__ == 1) /* USB DMA Mode 1 Short Packet Data Corruption */ -#define ANOMALY_05000450 (1 +#define ANOMALY_05000450 (1) +/* USB Receive Interrupt Is Not Generated in DMA Mode 1 */ +#define ANOMALY_05000456 (__SILICON_REVISION__ < 3) +/* False Hardware Error when RETI Points to Invalid Memory */ +#define ANOMALY_05000461 (1) +/* USB Rx DMA hang */ +#define ANOMALY_05000465 (1) +/* Possible RX data corruption when control & data EP FIFOs are accessed via the core */ +#define ANOMALY_05000467 (1) /* Anomalies that don't exist on this proc */ +#define ANOMALY_05000099 (0) +#define ANOMALY_05000120 (0) #define ANOMALY_05000125 (0) +#define ANOMALY_05000149 (0) #define ANOMALY_05000158 (0) +#define ANOMALY_05000171 (0) +#define ANOMALY_05000179 (0) +#define ANOMALY_05000182 (0) #define ANOMALY_05000183 (0) #define ANOMALY_05000198 (0) +#define ANOMALY_05000202 (0) +#define ANOMALY_05000215 (0) +#define ANOMALY_05000220 (0) +#define ANOMALY_05000227 (0) #define ANOMALY_05000230 (0) +#define ANOMALY_05000231 (0) +#define ANOMALY_05000233 (0) +#define ANOMALY_05000234 (0) +#define ANOMALY_05000242 (0) #define ANOMALY_05000244 (0) +#define ANOMALY_05000248 (0) +#define ANOMALY_05000250 (0) +#define ANOMALY_05000254 (0) +#define ANOMALY_05000257 (0) #define ANOMALY_05000261 (0) #define ANOMALY_05000263 (0) #define ANOMALY_05000266 (0) #define ANOMALY_05000273 (0) +#define ANOMALY_05000274 (0) #define ANOMALY_05000278 (0) +#define ANOMALY_05000283 (0) +#define ANOMALY_05000287 (0) +#define ANOMALY_05000301 (0) #define ANOMALY_05000305 (0) #define ANOMALY_05000307 (0) #define ANOMALY_05000311 (0) +#define ANOMALY_05000315 (0) #define ANOMALY_05000323 (0) +#define ANOMALY_05000362 (1) #define ANOMALY_05000363 (0) #define ANOMALY_05000380 (0) +#define ANOMALY_05000400 (0) #define ANOMALY_05000412 (0) #define ANOMALY_05000432 (0) #define ANOMALY_05000435 (0) diff --git a/arch/blackfin/mach-bf548/include/mach/blackfin.h b/arch/blackfin/mach-bf548/include/mach/blackfin.h index cf6c1500222a..6b97396d817f 100644 --- a/arch/blackfin/mach-bf548/include/mach/blackfin.h +++ b/arch/blackfin/mach-bf548/include/mach/blackfin.h @@ -33,7 +33,6 @@ #define _MACH_BLACKFIN_H_ #include "bf548.h" -#include "mem_map.h" #include "anomaly.h" #ifdef CONFIG_BF542 diff --git a/arch/blackfin/mach-bf548/include/mach/mem_map.h b/arch/blackfin/mach-bf548/include/mach/mem_map.h index 70b9c1194024..caac2dfb41eb 100644 --- a/arch/blackfin/mach-bf548/include/mach/mem_map.h +++ b/arch/blackfin/mach-bf548/include/mach/mem_map.h @@ -1,38 +1,16 @@ /* - * file: include/asm-blackfin/mach-bf548/mem_map.h - * based on: - * author: + * BF548 memory map * - * created: - * description: - * Memory MAP Common header file for blackfin BF537/6/4 of processors. - * rev: - * - * modified: - * - * bugs: enter bugs at http://blackfin.uclinux.org/ - * - * this program is free software; you can redistribute it and/or modify - * it under the terms of the gnu general public license as published by - * the free software foundation; either version 2, or (at your option) - * any later version. - * - * this program is distributed in the hope that it will be useful, - * but without any warranty; without even the implied warranty of - * merchantability or fitness for a particular purpose. see the - * gnu general public license for more details. - * - * you should have received a copy of the gnu general public license - * along with this program; see the file copying. - * if not, write to the free software foundation, - * 59 temple place - suite 330, boston, ma 02111-1307, usa. + * Copyright 2004-2009 Analog Devices Inc. + * Licensed under the GPL-2 or later. */ -#ifndef _MEM_MAP_548_H_ -#define _MEM_MAP_548_H_ +#ifndef __BFIN_MACH_MEM_MAP_H__ +#define __BFIN_MACH_MEM_MAP_H__ -#define COREMMR_BASE 0xFFE00000 /* Core MMRs */ -#define SYSMMR_BASE 0xFFC00000 /* System MMRs */ +#ifndef __BFIN_MEM_MAP_H__ +# error "do not include mach/mem_map.h directly -- use asm/mem_map.h" +#endif /* Async Memory Banks */ #define ASYNC_BANK3_BASE 0x2C000000 /* Async Bank 3 */ @@ -103,15 +81,4 @@ # define L2_LENGTH 0x20000 #endif -/* Scratch Pad Memory */ - -#define L1_SCRATCH_START 0xFFB00000 -#define L1_SCRATCH_LENGTH 0x1000 - -#define GET_PDA_SAFE(preg) \ - preg.l = _cpu_pda; \ - preg.h = _cpu_pda; - -#define GET_PDA(preg, dreg) GET_PDA_SAFE(preg) - -#endif/* _MEM_MAP_548_H_ */ +#endif diff --git a/arch/blackfin/mach-bf548/include/mach/portmux.h b/arch/blackfin/mach-bf548/include/mach/portmux.h index ffb1d0a44b4d..ce372ba0f046 100644 --- a/arch/blackfin/mach-bf548/include/mach/portmux.h +++ b/arch/blackfin/mach-bf548/include/mach/portmux.h @@ -167,22 +167,42 @@ #define P_PPI0_D13 (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(0)) #define P_PPI0_D14 (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(0)) #define P_PPI0_D15 (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(0)) -#define P_ATAPI_D0A (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(1)) -#define P_ATAPI_D1A (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(1)) -#define P_ATAPI_D2A (P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(1)) -#define P_ATAPI_D3A (P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(1)) -#define P_ATAPI_D4A (P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(1)) -#define P_ATAPI_D5A (P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(1)) -#define P_ATAPI_D6A (P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(1)) -#define P_ATAPI_D7A (P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(1)) -#define P_ATAPI_D8A (P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(1)) -#define P_ATAPI_D9A (P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(1)) -#define P_ATAPI_D10A (P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(1)) -#define P_ATAPI_D11A (P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(1)) -#define P_ATAPI_D12A (P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(1)) -#define P_ATAPI_D13A (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(1)) -#define P_ATAPI_D14A (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(1)) -#define P_ATAPI_D15A (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(1)) + +#ifdef CONFIG_BF548_ATAPI_ALTERNATIVE_PORT +# define P_ATAPI_D0A (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(1)) +# define P_ATAPI_D1A (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(1)) +# define P_ATAPI_D2A (P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(1)) +# define P_ATAPI_D3A (P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(1)) +# define P_ATAPI_D4A (P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(1)) +# define P_ATAPI_D5A (P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(1)) +# define P_ATAPI_D6A (P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(1)) +# define P_ATAPI_D7A (P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(1)) +# define P_ATAPI_D8A (P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(1)) +# define P_ATAPI_D9A (P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(1)) +# define P_ATAPI_D10A (P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(1)) +# define P_ATAPI_D11A (P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(1)) +# define P_ATAPI_D12A (P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(1)) +# define P_ATAPI_D13A (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(1)) +# define P_ATAPI_D14A (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(1)) +# define P_ATAPI_D15A (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(1)) +#else +# define P_ATAPI_D0A (P_DONTCARE) +# define P_ATAPI_D1A (P_DONTCARE) +# define P_ATAPI_D2A (P_DONTCARE) +# define P_ATAPI_D3A (P_DONTCARE) +# define P_ATAPI_D4A (P_DONTCARE) +# define P_ATAPI_D5A (P_DONTCARE) +# define P_ATAPI_D6A (P_DONTCARE) +# define P_ATAPI_D7A (P_DONTCARE) +# define P_ATAPI_D8A (P_DONTCARE) +# define P_ATAPI_D9A (P_DONTCARE) +# define P_ATAPI_D10A (P_DONTCARE) +# define P_ATAPI_D11A (P_DONTCARE) +# define P_ATAPI_D12A (P_DONTCARE) +# define P_ATAPI_D13A (P_DONTCARE) +# define P_ATAPI_D14A (P_DONTCARE) +# define P_ATAPI_D15A (P_DONTCARE) +#endif #define P_PPI0_CLK (P_DEFINED | P_IDENT(GPIO_PG0) | P_FUNCT(0)) #define P_PPI0_FS1 (P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(0)) @@ -200,9 +220,15 @@ #define P_CAN0_RX (P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(0)) #define P_CAN1_TX (P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(0)) #define P_CAN1_RX (P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(0)) -#define P_ATAPI_A0A (P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(1)) -#define P_ATAPI_A1A (P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(1)) -#define P_ATAPI_A2A (P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(1)) +#ifdef CONFIG_BF548_ATAPI_ALTERNATIVE_PORT +# define P_ATAPI_A0A (P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(1)) +# define P_ATAPI_A1A (P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(1)) +# define P_ATAPI_A2A (P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(1)) +#else +# define P_ATAPI_A0A (P_DONTCARE) +# define P_ATAPI_A1A (P_DONTCARE) +# define P_ATAPI_A2A (P_DONTCARE) +#endif #define P_HOST_CE (P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(1)) #define P_HOST_RD (P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(1)) #define P_HOST_WR (P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(1)) |