diff options
Diffstat (limited to 'arch/blackfin/mach-bf548/boards/ezkit.c')
| -rw-r--r-- | arch/blackfin/mach-bf548/boards/ezkit.c | 109 |
1 files changed, 97 insertions, 12 deletions
diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c index 096e661700a7..81f5b95cc361 100644 --- a/arch/blackfin/mach-bf548/boards/ezkit.c +++ b/arch/blackfin/mach-bf548/boards/ezkit.c @@ -76,7 +76,6 @@ static struct resource bfin_isp1760_resources[] = { static struct isp1760_platform_data isp1760_priv = { .is_isp1761 = 0, - .port1_disable = 0, .bus_width_16 = 1, .port1_otg = 0, .analog_oc = 0, @@ -208,6 +207,43 @@ static struct platform_device bfin_rotary_device = { }; #endif +#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE) +#include <linux/input.h> +#include <linux/spi/adxl34x.h> +static const struct adxl34x_platform_data adxl34x_info = { + .x_axis_offset = 0, + .y_axis_offset = 0, + .z_axis_offset = 0, + .tap_threshold = 0x31, + .tap_duration = 0x10, + .tap_latency = 0x60, + .tap_window = 0xF0, + .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN, + .act_axis_control = 0xFF, + .activity_threshold = 5, + .inactivity_threshold = 3, + .inactivity_time = 4, + .free_fall_threshold = 0x7, + .free_fall_time = 0x20, + .data_rate = 0x8, + .data_range = ADXL_FULL_RES, + + .ev_type = EV_ABS, + .ev_code_x = ABS_X, /* EV_REL */ + .ev_code_y = ABS_Y, /* EV_REL */ + .ev_code_z = ABS_Z, /* EV_REL */ + + .ev_code_tap_x = BTN_TOUCH, /* EV_KEY */ + .ev_code_tap_y = BTN_TOUCH, /* EV_KEY */ + .ev_code_tap_z = BTN_TOUCH, /* EV_KEY */ + +/* .ev_code_ff = KEY_F,*/ /* EV_KEY */ +/* .ev_code_act_inactivity = KEY_A,*/ /* EV_KEY */ + .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK, + .fifo_mode = ADXL_FIFO_STREAM, +}; +#endif + #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) static struct platform_device rtc_device = { .name = "rtc-bfin", @@ -359,6 +395,8 @@ static struct platform_device bfin_sir3_device = { #endif #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#include <linux/smsc911x.h> + static struct resource smsc911x_resources[] = { { .name = "smsc911x-memory", @@ -372,11 +410,22 @@ static struct resource smsc911x_resources[] = { .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, }, }; + +static struct smsc911x_platform_config smsc911x_config = { + .flags = SMSC911X_USE_32BIT, + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, + .phy_interface = PHY_INTERFACE_MODE_MII, +}; + static struct platform_device smsc911x_device = { .name = "smsc911x", .id = 0, .num_resources = ARRAY_SIZE(smsc911x_resources), .resource = smsc911x_resources, + .dev = { + .platform_data = &smsc911x_config, + }, }; #endif @@ -628,6 +677,14 @@ static struct bfin5xx_spi_chip spidev_chip_info = { }; #endif +#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE) +static struct bfin5xx_spi_chip spi_adxl34x_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, + .cs_change_per_word = 0, +}; +#endif + static struct spi_board_info bfin_spi_board_info[] __initdata = { #if defined(CONFIG_MTD_M25P80) \ || defined(CONFIG_MTD_M25P80_MODULE) @@ -653,15 +710,15 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { }, #endif #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) -{ - .modalias = "ad7877", - .platform_data = &bfin_ad7877_ts_info, - .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */ - .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ - .bus_num = 0, - .chip_select = 2, - .controller_data = &spi_ad7877_chip_info, -}, + { + .modalias = "ad7877", + .platform_data = &bfin_ad7877_ts_info, + .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */ + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 2, + .controller_data = &spi_ad7877_chip_info, + }, #endif #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) { @@ -672,8 +729,19 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { .controller_data = &spidev_chip_info, }, #endif +#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE) + { + .modalias = "adxl34x", + .platform_data = &adxl34x_info, + .irq = IRQ_PC5, + .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = 2, + .controller_data = &spi_adxl34x_chip_info, + .mode = SPI_MODE_3, + }, +#endif }; - #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) /* SPI (0) */ static struct resource bfin_spi0_resource[] = { @@ -685,6 +753,11 @@ static struct resource bfin_spi0_resource[] = { [1] = { .start = CH_SPI0, .end = CH_SPI0, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI0, + .end = IRQ_SPI0, .flags = IORESOURCE_IRQ, } }; @@ -699,6 +772,11 @@ static struct resource bfin_spi1_resource[] = { [1] = { .start = CH_SPI1, .end = CH_SPI1, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI1, + .end = IRQ_SPI1, .flags = IORESOURCE_IRQ, } }; @@ -786,7 +864,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info0[] = { #if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */ static struct i2c_board_info __initdata bfin_i2c_board_info1[] = { -#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE) +#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE) { I2C_BOARD_INFO("pcf8574_lcd", 0x22), }, @@ -797,6 +875,13 @@ static struct i2c_board_info __initdata bfin_i2c_board_info1[] = { .irq = 212, }, #endif +#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE) + { + I2C_BOARD_INFO("adxl34x", 0x53), + .irq = IRQ_PC5, + .platform_data = (void *)&adxl34x_info, + }, +#endif }; #endif |