Diffstat (limited to 'Documentation')
4 files changed, 29 insertions, 16 deletions
diff --git a/Documentation/RCU/checklist.txt b/Documentation/RCU/checklist.txt
index 0c134f8afc6f..bff2d8be1e18 100644
@@ -328,6 +328,12 @@ over a rather long period of time, but improvements are always welcome!
RCU rather than SRCU, because RCU is almost always faster and
easier to use than is SRCU.
+ If you need to enter your read-side critical section in a
+ hardirq or exception handler, and then exit that same read-side
+ critical section in the task that was interrupted, then you need
+ to srcu_read_lock_raw() and srcu_read_unlock_raw(), which avoid
+ the lockdep checking that would otherwise this practice illegal.
Also unlike other forms of RCU, explicit initialization
and cleanup is required via init_srcu_struct() and
cleanup_srcu_struct(). These are passed a "struct srcu_struct"
diff --git a/Documentation/RCU/rcu.txt b/Documentation/RCU/rcu.txt
index 31852705b586..bf778332a28f 100644
@@ -38,11 +38,11 @@ o How can the updater tell when a grace period has completed
Preemptible variants of RCU (CONFIG_TREE_PREEMPT_RCU) get the
same effect, but require that the readers manipulate CPU-local
- counters. These counters allow limited types of blocking
- within RCU read-side critical sections. SRCU also uses
- CPU-local counters, and permits general blocking within
- RCU read-side critical sections. These two variants of
- RCU detect grace periods by sampling these counters.
+ counters. These counters allow limited types of blocking within
+ RCU read-side critical sections. SRCU also uses CPU-local
+ counters, and permits general blocking within RCU read-side
+ critical sections. These variants of RCU detect grace periods
+ by sampling these counters.
o If I am running on a uniprocessor kernel, which can only do one
thing at a time, why should I wait for a grace period?
diff --git a/Documentation/RCU/stallwarn.txt b/Documentation/RCU/stallwarn.txt
index f3e0625f4290..083d88cbc089 100644
@@ -114,12 +114,11 @@ o A hardware failure. This is quite unlikely, but has occurred
This resulted in a series of RCU CPU stall warnings, eventually
leading the realization that the CPU had failed.
-The RCU, RCU-sched, and RCU-bh implementations have CPU stall
-warning. SRCU does not have its own CPU stall warnings, but its
-calls to synchronize_sched() will result in RCU-sched detecting
-RCU-sched-related CPU stalls. Please note that RCU only detects
-CPU stalls when there is a grace period in progress. No grace period,
-no CPU stall warnings.
+The RCU, RCU-sched, and RCU-bh implementations have CPU stall warning.
+SRCU does not have its own CPU stall warnings, but its calls to
+synchronize_sched() will result in RCU-sched detecting RCU-sched-related
+CPU stalls. Please note that RCU only detects CPU stalls when there is
+a grace period in progress. No grace period, no CPU stall warnings.
To diagnose the cause of the stall, inspect the stack traces.
The offending function will usually be near the top of the stack.
diff --git a/Documentation/RCU/whatisRCU.txt b/Documentation/RCU/whatisRCU.txt
index 6ef692667e2f..8e8cdc2430b9 100644
@@ -834,6 +834,8 @@ SRCU: Critical sections Grace period Barrier
srcu_read_lock synchronize_srcu N/A
@@ -855,27 +857,33 @@ list can be helpful:
a. Will readers need to block? If so, you need SRCU.
-b. What about the -rt patchset? If readers would need to block
+b. Is it necessary to start a read-side critical section in a
+ hardirq handler or exception handler, and then to complete
+ this read-side critical section in the task that was
+ interrupted? If so, you need SRCU's srcu_read_lock_raw() and
+ srcu_read_unlock_raw() primitives.
+c. What about the -rt patchset? If readers would need to block
in an non-rt kernel, you need SRCU. If readers would block
in a -rt kernel, but not in a non-rt kernel, SRCU is not
-c. Do you need to treat NMI handlers, hardirq handlers,
+d. Do you need to treat NMI handlers, hardirq handlers,
and code segments with preemption disabled (whether
via preempt_disable(), local_irq_save(), local_bh_disable(),
or some other mechanism) as if they were explicit RCU readers?
If so, you need RCU-sched.
-d. Do you need RCU grace periods to complete even in the face
+e. Do you need RCU grace periods to complete even in the face
of softirq monopolization of one or more of the CPUs? For
example, is your code subject to network-based denial-of-service
attacks? If so, you need RCU-bh.
-e. Is your workload too update-intensive for normal use of
+f. Is your workload too update-intensive for normal use of
RCU, but inappropriate for other synchronization mechanisms?
If so, consider SLAB_DESTROY_BY_RCU. But please be careful!
-f. Otherwise, use RCU.
+g. Otherwise, use RCU.
Of course, this all assumes that you have determined that RCU is in fact
the right tool for your job.