diff options
Diffstat (limited to 'Documentation')
131 files changed, 8407 insertions, 336 deletions
diff --git a/Documentation/ABI/testing/sysfs-block-rssd b/Documentation/ABI/testing/sysfs-block-rssd index d535757799fe..679ce3543122 100644 --- a/Documentation/ABI/testing/sysfs-block-rssd +++ b/Documentation/ABI/testing/sysfs-block-rssd @@ -6,13 +6,21 @@ Description: This is a read-only file. Dumps below driver information and hardware registers. - S ACTive - Command Issue - - Allocated - Completed - PORT IRQ STAT - HOST IRQ STAT + - Allocated + - Commands in Q What: /sys/block/rssd*/status Date: April 2012 KernelVersion: 3.4 Contact: Asai Thambi S P <asamymuthupa@micron.com> -Description: This is a read-only file. Indicates the status of the device. +Description: This is a read-only file. Indicates the status of the device. + +What: /sys/block/rssd*/flags +Date: May 2012 +KernelVersion: 3.5 +Contact: Asai Thambi S P <asamymuthupa@micron.com> +Description: This is a read-only file. Dumps the flags in port and driver + data structure diff --git a/Documentation/ABI/testing/sysfs-bus-fcoe b/Documentation/ABI/testing/sysfs-bus-fcoe new file mode 100644 index 000000000000..469d09c02f6b --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-fcoe @@ -0,0 +1,77 @@ +What: /sys/bus/fcoe/ctlr_X +Date: March 2012 +KernelVersion: TBD +Contact: Robert Love <robert.w.love@intel.com>, devel@open-fcoe.org +Description: 'FCoE Controller' instances on the fcoe bus +Attributes: + + fcf_dev_loss_tmo: Device loss timeout peroid (see below). Changing + this value will change the dev_loss_tmo for all + FCFs discovered by this controller. + + lesb_link_fail: Link Error Status Block (LESB) link failure count. + + lesb_vlink_fail: Link Error Status Block (LESB) virtual link + failure count. + + lesb_miss_fka: Link Error Status Block (LESB) missed FCoE + Initialization Protocol (FIP) Keep-Alives (FKA). + + lesb_symb_err: Link Error Status Block (LESB) symbolic error count. + + lesb_err_block: Link Error Status Block (LESB) block error count. + + lesb_fcs_error: Link Error Status Block (LESB) Fibre Channel + Serivces error count. + +Notes: ctlr_X (global increment starting at 0) + +What: /sys/bus/fcoe/fcf_X +Date: March 2012 +KernelVersion: TBD +Contact: Robert Love <robert.w.love@intel.com>, devel@open-fcoe.org +Description: 'FCoE FCF' instances on the fcoe bus. A FCF is a Fibre Channel + Forwarder, which is a FCoE switch that can accept FCoE + (Ethernet) packets, unpack them, and forward the embedded + Fibre Channel frames into a FC fabric. It can also take + outbound FC frames and pack them in Ethernet packets to + be sent to their destination on the Ethernet segment. +Attributes: + + fabric_name: Identifies the fabric that the FCF services. + + switch_name: Identifies the FCF. + + priority: The switch's priority amongst other FCFs on the same + fabric. + + selected: 1 indicates that the switch has been selected for use; + 0 indicates that the swich will not be used. + + fc_map: The Fibre Channel MAP + + vfid: The Virtual Fabric ID + + mac: The FCF's MAC address + + fka_peroid: The FIP Keep-Alive peroid + + fabric_state: The internal kernel state + "Unknown" - Initialization value + "Disconnected" - No link to the FCF/fabric + "Connected" - Host is connected to the FCF + "Deleted" - FCF is being removed from the system + + dev_loss_tmo: The device loss timeout peroid for this FCF. + +Notes: A device loss infrastructre similar to the FC Transport's + is present in fcoe_sysfs. It is nice to have so that a + link flapping adapter doesn't continually advance the count + used to identify the discovered FCF. FCFs will exist in a + "Disconnected" state until either the timer expires and the + FCF becomes "Deleted" or the FCF is rediscovered and becomes + "Connected." + + +Users: The first user of this interface will be the fcoeadm application, + which is commonly packaged in the fcoe-utils package. diff --git a/Documentation/ABI/testing/sysfs-bus-i2c-devices-lm3533 b/Documentation/ABI/testing/sysfs-bus-i2c-devices-lm3533 new file mode 100644 index 000000000000..1b62230b33b9 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-i2c-devices-lm3533 @@ -0,0 +1,15 @@ +What: /sys/bus/i2c/devices/.../output_hvled[n] +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the controlling backlight device for high-voltage current + sink HVLED[n] (n = 1, 2) (0, 1). + +What: /sys/bus/i2c/devices/.../output_lvled[n] +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the controlling led device for low-voltage current sink + LVLED[n] (n = 1..5) (0..3). diff --git a/Documentation/ABI/testing/sysfs-bus-rbd b/Documentation/ABI/testing/sysfs-bus-rbd index dbedafb095e2..bcd88eb7ebcd 100644 --- a/Documentation/ABI/testing/sysfs-bus-rbd +++ b/Documentation/ABI/testing/sysfs-bus-rbd @@ -65,11 +65,11 @@ snap_* Entries under /sys/bus/rbd/devices/<dev-id>/snap_<snap-name> ------------------------------------------------------------- -id +snap_id The rados internal snapshot id assigned for this snapshot -size +snap_size The size of the image when this snapshot was taken. diff --git a/Documentation/ABI/testing/sysfs-class-backlight-driver-lm3533 b/Documentation/ABI/testing/sysfs-class-backlight-driver-lm3533 new file mode 100644 index 000000000000..77cf7ac949af --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-backlight-driver-lm3533 @@ -0,0 +1,48 @@ +What: /sys/class/backlight/<backlight>/als_channel +Date: May 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Get the ALS output channel used as input in + ALS-current-control mode (0, 1), where + + 0 - out_current0 (backlight 0) + 1 - out_current1 (backlight 1) + +What: /sys/class/backlight/<backlight>/als_en +Date: May 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Enable ALS-current-control mode (0, 1). + +What: /sys/class/backlight/<backlight>/id +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Get the id of this backlight (0, 1). + +What: /sys/class/backlight/<backlight>/linear +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the brightness-mapping mode (0, 1), where + + 0 - exponential mode + 1 - linear mode + +What: /sys/class/backlight/<backlight>/pwm +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the PWM-input control mask (5 bits), where + + bit 5 - PWM-input enabled in Zone 4 + bit 4 - PWM-input enabled in Zone 3 + bit 3 - PWM-input enabled in Zone 2 + bit 2 - PWM-input enabled in Zone 1 + bit 1 - PWM-input enabled in Zone 0 + bit 0 - PWM-input enabled diff --git a/Documentation/ABI/testing/sysfs-class-led-driver-lm3533 b/Documentation/ABI/testing/sysfs-class-led-driver-lm3533 new file mode 100644 index 000000000000..620ebb3b9baa --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-led-driver-lm3533 @@ -0,0 +1,65 @@ +What: /sys/class/leds/<led>/als_channel +Date: May 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the ALS output channel to use as input in + ALS-current-control mode (1, 2), where + + 1 - out_current1 + 2 - out_current2 + +What: /sys/class/leds/<led>/als_en +Date: May 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Enable ALS-current-control mode (0, 1). + +What: /sys/class/leds/<led>/falltime +What: /sys/class/leds/<led>/risetime +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the pattern generator fall and rise times (0..7), where + + 0 - 2048 us + 1 - 262 ms + 2 - 524 ms + 3 - 1.049 s + 4 - 2.097 s + 5 - 4.194 s + 6 - 8.389 s + 7 - 16.78 s + +What: /sys/class/leds/<led>/id +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Get the id of this led (0..3). + +What: /sys/class/leds/<led>/linear +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the brightness-mapping mode (0, 1), where + + 0 - exponential mode + 1 - linear mode + +What: /sys/class/leds/<led>/pwm +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the PWM-input control mask (5 bits), where + + bit 5 - PWM-input enabled in Zone 4 + bit 4 - PWM-input enabled in Zone 3 + bit 3 - PWM-input enabled in Zone 2 + bit 2 - PWM-input enabled in Zone 1 + bit 1 - PWM-input enabled in Zone 0 + bit 0 - PWM-input enabled diff --git a/Documentation/ABI/testing/sysfs-driver-wacom b/Documentation/ABI/testing/sysfs-driver-wacom index 56c54558c8a4..8d55a83d6921 100644 --- a/Documentation/ABI/testing/sysfs-driver-wacom +++ b/Documentation/ABI/testing/sysfs-driver-wacom @@ -23,9 +23,10 @@ Contact: linux-input@vger.kernel.org Description: Attribute group for control of the status LEDs and the OLEDs. This attribute group is only available for Intuos 4 M, L, - and XL (with LEDs and OLEDs) and Cintiq 21UX2 and Cintiq 24HD - (LEDs only). Therefore its presence implicitly signifies the - presence of said LEDs and OLEDs on the tablet device. + and XL (with LEDs and OLEDs), Intuos 5 (LEDs only), and Cintiq + 21UX2 and Cintiq 24HD (LEDs only). Therefore its presence + implicitly signifies the presence of said LEDs and OLEDs on the + tablet device. What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status0_luminance Date: August 2011 @@ -48,10 +49,10 @@ What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status_led0 Date: August 2011 Contact: linux-input@vger.kernel.org Description: - Writing to this file sets which one of the four (for Intuos 4) - or of the right four (for Cintiq 21UX2 and Cintiq 24HD) status - LEDs is active (0..3). The other three LEDs on the same side are - always inactive. + Writing to this file sets which one of the four (for Intuos 4 + and Intuos 5) or of the right four (for Cintiq 21UX2 and Cintiq + 24HD) status LEDs is active (0..3). The other three LEDs on the + same side are always inactive. What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status_led1_select Date: September 2011 diff --git a/Documentation/CodingStyle b/Documentation/CodingStyle index c58b236bbe04..cb9258b8fd35 100644 --- a/Documentation/CodingStyle +++ b/Documentation/CodingStyle @@ -671,8 +671,9 @@ ones already enabled by DEBUG. Chapter 14: Allocating memory The kernel provides the following general purpose memory allocators: -kmalloc(), kzalloc(), kcalloc(), vmalloc(), and vzalloc(). Please refer to -the API documentation for further information about them. +kmalloc(), kzalloc(), kmalloc_array(), kcalloc(), vmalloc(), and +vzalloc(). Please refer to the API documentation for further information +about them. The preferred form for passing a size of a struct is the following: @@ -686,6 +687,17 @@ Casting the return value which is a void pointer is redundant. The conversion from void pointer to any other pointer type is guaranteed by the C programming language. +The preferred form for allocating an array is the following: + + p = kmalloc_array(n, sizeof(...), ...); + +The preferred form for allocating a zeroed array is the following: + + p = kcalloc(n, sizeof(...), ...); + +Both forms check for overflow on the allocation size n * sizeof(...), +and return NULL if that occurred. + Chapter 15: The inline disease diff --git a/Documentation/DocBook/media/Makefile b/Documentation/DocBook/media/Makefile index 6628b4b9cac4..362520992ced 100644 --- a/Documentation/DocBook/media/Makefile +++ b/Documentation/DocBook/media/Makefile @@ -70,6 +70,8 @@ IOCTLS = \ VIDIOC_SUBDEV_ENUM_MBUS_CODE \ VIDIOC_SUBDEV_ENUM_FRAME_SIZE \ VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL \ + VIDIOC_SUBDEV_G_SELECTION \ + VIDIOC_SUBDEV_S_SELECTION \ TYPES = \ $(shell perl -ne 'print "$$1 " if /^typedef\s+[^\s]+\s+([^\s]+)\;/' $(srctree)/include/linux/videodev2.h) \ @@ -193,7 +195,7 @@ DVB_DOCUMENTED = \ # install_media_images = \ - $(Q)cp $(OBJIMGFILES) $(MEDIA_OBJ_DIR)/media_api + $(Q)cp $(OBJIMGFILES) $(MEDIA_SRC_DIR)/v4l/*.svg $(MEDIA_OBJ_DIR)/media_api $(MEDIA_OBJ_DIR)/%: $(MEDIA_SRC_DIR)/%.b64 $(Q)base64 -d $< >$@ diff --git a/Documentation/DocBook/media/dvb/dvbproperty.xml b/Documentation/DocBook/media/dvb/dvbproperty.xml index c7a4ca517859..e633c097a8d1 100644 --- a/Documentation/DocBook/media/dvb/dvbproperty.xml +++ b/Documentation/DocBook/media/dvb/dvbproperty.xml @@ -531,6 +531,139 @@ typedef enum fe_delivery_system { here are referring to what can be found in the TMCC-structure - independent of the mode.</para> </section> + <section id="DTV-ATSCMH-FIC-VER"> + <title><constant>DTV_ATSCMH_FIC_VER</constant></title> + <para>Version number of the FIC (Fast Information Channel) signaling data.</para> + <para>FIC is used for relaying information to allow rapid service acquisition by the receiver.</para> + <para>Possible values: 0, 1, 2, 3, ..., 30, 31</para> + </section> + <section id="DTV-ATSCMH-PARADE-ID"> + <title><constant>DTV_ATSCMH_PARADE_ID</constant></title> + <para>Parade identification number</para> + <para>A parade is a collection of up to eight MH groups, conveying one or two ensembles.</para> + <para>Possible values: 0, 1, 2, 3, ..., 126, 127</para> + </section> + <section id="DTV-ATSCMH-NOG"> + <title><constant>DTV_ATSCMH_NOG</constant></title> + <para>Number of MH groups per MH subframe for a designated parade.</para> + <para>Possible values: 1, 2, 3, 4, 5, 6, 7, 8</para> + </section> + <section id="DTV-ATSCMH-TNOG"> + <title><constant>DTV_ATSCMH_TNOG</constant></title> + <para>Total number of MH groups including all MH groups belonging to all MH parades in one MH subframe.</para> + <para>Possible values: 0, 1, 2, 3, ..., 30, 31</para> + </section> + <section id="DTV-ATSCMH-SGN"> + <title><constant>DTV_ATSCMH_SGN</constant></title> + <para>Start group number.</para> + <para>Possible values: 0, 1, 2, 3, ..., 14, 15</para> + </section> + <section id="DTV-ATSCMH-PRC"> + <title><constant>DTV_ATSCMH_PRC</constant></title> + <para>Parade repetition cycle.</para> + <para>Possible values: 1, 2, 3, 4, 5, 6, 7, 8</para> + </section> + <section id="DTV-ATSCMH-RS-FRAME-MODE"> + <title><constant>DTV_ATSCMH_RS_FRAME_MODE</constant></title> + <para>RS frame mode.</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_rs_frame_mode { + ATSCMH_RSFRAME_PRI_ONLY = 0, + ATSCMH_RSFRAME_PRI_SEC = 1, +} atscmh_rs_frame_mode_t; +</programlisting> + </section> + <section id="DTV-ATSCMH-RS-FRAME-ENSEMBLE"> + <title><constant>DTV_ATSCMH_RS_FRAME_ENSEMBLE</constant></title> + <para>RS frame ensemble.</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_rs_frame_ensemble { + ATSCMH_RSFRAME_ENS_PRI = 0, + ATSCMH_RSFRAME_ENS_SEC = 1, +} atscmh_rs_frame_ensemble_t; +</programlisting> + </section> + <section id="DTV-ATSCMH-RS-CODE-MODE-PRI"> + <title><constant>DTV_ATSCMH_RS_CODE_MODE_PRI</constant></title> + <para>RS code mode (primary).</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_rs_code_mode { + ATSCMH_RSCODE_211_187 = 0, + ATSCMH_RSCODE_223_187 = 1, + ATSCMH_RSCODE_235_187 = 2, +} atscmh_rs_code_mode_t; +</programlisting> + </section> + <section id="DTV-ATSCMH-RS-CODE-MODE-SEC"> + <title><constant>DTV_ATSCMH_RS_CODE_MODE_SEC</constant></title> + <para>RS code mode (secondary).</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_rs_code_mode { + ATSCMH_RSCODE_211_187 = 0, + ATSCMH_RSCODE_223_187 = 1, + ATSCMH_RSCODE_235_187 = 2, +} atscmh_rs_code_mode_t; +</programlisting> + </section> + <section id="DTV-ATSCMH-SCCC-BLOCK-MODE"> + <title><constant>DTV_ATSCMH_SCCC_BLOCK_MODE</constant></title> + <para>Series Concatenated Convolutional Code Block Mode.</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_sccc_block_mode { + ATSCMH_SCCC_BLK_SEP = 0, + ATSCMH_SCCC_BLK_COMB = 1, +} atscmh_sccc_block_mode_t; +</programlisting> + </section> + <section id="DTV-ATSCMH-SCCC-CODE-MODE-A"> + <title><constant>DTV_ATSCMH_SCCC_CODE_MODE_A</constant></title> + <para>Series Concatenated Convolutional Code Rate.</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_sccc_code_mode { + ATSCMH_SCCC_CODE_HLF = 0, + ATSCMH_SCCC_CODE_QTR = 1, +} atscmh_sccc_code_mode_t; +</programlisting> + </section> + <section id="DTV-ATSCMH-SCCC-CODE-MODE-B"> + <title><constant>DTV_ATSCMH_SCCC_CODE_MODE_B</constant></title> + <para>Series Concatenated Convolutional Code Rate.</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_sccc_code_mode { + ATSCMH_SCCC_CODE_HLF = 0, + ATSCMH_SCCC_CODE_QTR = 1, +} atscmh_sccc_code_mode_t; +</programlisting> + </section> + <section id="DTV-ATSCMH-SCCC-CODE-MODE-C"> + <title><constant>DTV_ATSCMH_SCCC_CODE_MODE_C</constant></title> + <para>Series Concatenated Convolutional Code Rate.</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_sccc_code_mode { + ATSCMH_SCCC_CODE_HLF = 0, + ATSCMH_SCCC_CODE_QTR = 1, +} atscmh_sccc_code_mode_t; +</programlisting> + </section> + <section id="DTV-ATSCMH-SCCC-CODE-MODE-D"> + <title><constant>DTV_ATSCMH_SCCC_CODE_MODE_D</constant></title> + <para>Series Concatenated Convolutional Code Rate.</para> + <para>Possible values are:</para> +<programlisting> +typedef enum atscmh_sccc_code_mode { + ATSCMH_SCCC_CODE_HLF = 0, + ATSCMH_SCCC_CODE_QTR = 1, +} atscmh_sccc_code_mode_t; +</programlisting> + </section> </section> <section id="DTV-API-VERSION"> <title><constant>DTV_API_VERSION</constant></title> @@ -774,6 +907,33 @@ typedef enum fe_hierarchy { <listitem><para><link linkend="DTV-BANDWIDTH-HZ"><constant>DTV_BANDWIDTH_HZ</constant></link></para></listitem> </itemizedlist> </section> + <section id="atscmh-params"> + <title>ATSC-MH delivery system</title> + <para>The following parameters are valid for ATSC-MH:</para> + <itemizedlist mark='opencircle'> + <listitem><para><link linkend="DTV-API-VERSION"><constant>DTV_API_VERSION</constant></link></para></listitem> + <listitem><para><link linkend="DTV-DELIVERY-SYSTEM"><constant>DTV_DELIVERY_SYSTEM</constant></link></para></listitem> + <listitem><para><link linkend="DTV-TUNE"><constant>DTV_TUNE</constant></link></para></listitem> + <listitem><para><link linkend="DTV-CLEAR"><constant>DTV_CLEAR</constant></link></para></listitem> + <listitem><para><link linkend="DTV-FREQUENCY"><constant>DTV_FREQUENCY</constant></link></para></listitem> + <listitem><para><link linkend="DTV-BANDWIDTH-HZ"><constant>DTV_BANDWIDTH_HZ</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-FIC-VER"><constant>DTV_ATSCMH_FIC_VER</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-PARADE-ID"><constant>DTV_ATSCMH_PARADE_ID</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-NOG"><constant>DTV_ATSCMH_NOG</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-TNOG"><constant>DTV_ATSCMH_TNOG</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-SGN"><constant>DTV_ATSCMH_SGN</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-PRC"><constant>DTV_ATSCMH_PRC</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-RS-FRAME-MODE"><constant>DTV_ATSCMH_RS_FRAME_MODE</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-RS-FRAME-ENSEMBLE"><constant>DTV_ATSCMH_RS_FRAME_ENSEMBLE</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-CODE-MODE-PRI"><constant>DTV_ATSCMH_CODE_MODE_PRI</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-CODE-MODE-SEC"><constant>DTV_ATSCMH_CODE_MODE_SEC</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-SCCC-BLOCK-MODE"><constant>DTV_ATSCMH_SCCC_BLOCK_MODE</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-SCCC-CODE_MODE-A"><constant>DTV_ATSCMH_SCCC_CODE_MODE_A</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-SCCC-CODE_MODE-B"><constant>DTV_ATSCMH_SCCC_CODE_MODE_B</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-SCCC-CODE_MODE-C"><constant>DTV_ATSCMH_SCCC_CODE_MODE_C</constant></link></para></listitem> + <listitem><para><link linkend="DTV-ATSCMH-SCCC-CODE_MODE-D"><constant>DTV_ATSCMH_SCCC_CODE_MODE_D</constant></link></para></listitem> + </itemizedlist> + </section> </section> <section id="frontend-property-cable-systems"> <title>Properties used on cable delivery systems</title> diff --git a/Documentation/DocBook/media/v4l/biblio.xml b/Documentation/DocBook/media/v4l/biblio.xml index 7dc65c592a87..7c49facecd25 100644 --- a/Documentation/DocBook/media/v4l/biblio.xml +++ b/Documentation/DocBook/media/v4l/biblio.xml @@ -197,4 +197,33 @@ in the frequency range from 87,5 to 108,0 MHz</title> <title>NTSC-4: United States RBDS Standard</title> </biblioentry> + <biblioentry id="iso12232"> + <abbrev>ISO 12232:2006</abbrev> + <authorgroup> + <corpauthor>International Organization for Standardization +(<ulink url="http://www.iso.org">http://www.iso.org</ulink>)</corpauthor> + </authorgroup> + <title>Photography — Digital still cameras — Determination + of exposure index, ISO speed ratings, standard output sensitivity, and + recommended exposure index</title> + </biblioentry> + + <biblioentry id="cea861"> + <abbrev>CEA-861-E</abbrev> + <authorgroup> + <corpauthor>Consumer Electronics Association +(<ulink url="http://www.ce.org">http://www.ce.org</ulink>)</corpauthor> + </authorgroup> + <title>A DTV Profile for Uncompressed High Speed Digital Interfaces</title> + </biblioentry> + + <biblioentry id="vesadmt"> + <abbrev>VESA DMT</abbrev> + <authorgroup> + <corpauthor>Video Electronics Standards Association +(<ulink url="http://www.vesa.org">http://www.vesa.org</ulink>)</corpauthor> + </authorgroup> + <title>VESA and Industry Standards and Guidelines for Computer Display Monitor Timing (DMT)</title> + </biblioentry> + </bibliography> diff --git a/Documentation/DocBook/media/v4l/common.xml b/Documentation/DocBook/media/v4l/common.xml index c79278acfb0e..4101aeb56540 100644 --- a/Documentation/DocBook/media/v4l/common.xml +++ b/Documentation/DocBook/media/v4l/common.xml @@ -724,41 +724,49 @@ if (-1 == ioctl (fd, &VIDIOC-S-STD;, &std_id)) { } </programlisting> </example> + </section> <section id="dv-timings"> <title>Digital Video (DV) Timings</title> <para> - The video standards discussed so far has been dealing with Analog TV and the + The video standards discussed so far have been dealing with Analog TV and the corresponding video timings. Today there are many more different hardware interfaces such as High Definition TV interfaces (HDMI), VGA, DVI connectors etc., that carry video signals and there is a need to extend the API to select the video timings for these interfaces. Since it is not possible to extend the &v4l2-std-id; due to -the limited bits available, a new set of IOCTLs is added to set/get video timings at +the limited bits available, a new set of IOCTLs was added to set/get video timings at the input and output: </para><itemizedlist> <listitem> - <para>DV Presets: Digital Video (DV) presets. These are IDs representing a + <para>DV Timings: This will allow applications to define detailed +video timings for the interface. This includes parameters such as width, height, +polarities, frontporch, backporch etc. The <filename>linux/v4l2-dv-timings.h</filename> +header can be used to get the timings of the formats in the <xref linkend="cea861" /> and +<xref linkend="vesadmt" /> standards. + </para> + </listitem> + <listitem> + <para>DV Presets: Digital Video (DV) presets (<emphasis role="bold">deprecated</emphasis>). + These are IDs representing a video timing at the input/output. Presets are pre-defined timings implemented by the hardware according to video standards. A __u32 data type is used to represent a preset unlike the bit mask that is used in &v4l2-std-id; allowing future extensions -to support as many different presets as needed.</para> - </listitem> - <listitem> - <para>Custom DV Timings: This will allow applications to define more detailed -custom video timings for the interface. This includes parameters such as width, height, -polarities, frontporch, backporch etc. - </para> +to support as many different presets as needed. This API is deprecated in favor of the DV Timings +API.</para> </listitem> </itemizedlist> + <para>To enumerate and query the attributes of the DV timings supported by a device, + applications use the &VIDIOC-ENUM-DV-TIMINGS; and &VIDIOC-DV-TIMINGS-CAP; ioctls. + To set DV timings for the device, applications use the +&VIDIOC-S-DV-TIMINGS; ioctl and to get current DV timings they use the +&VIDIOC-G-DV-TIMINGS; ioctl. To detect the DV timings as seen by the video receiver applications +use the &VIDIOC-QUERY-DV-TIMINGS; ioctl.</para> <para>To enumerate and query the attributes of DV presets supported by a device, applications use the &VIDIOC-ENUM-DV-PRESETS; ioctl. To get the current DV preset, applications use the &VIDIOC-G-DV-PRESET; ioctl and to set a preset they use the -&VIDIOC-S-DV-PRESET; ioctl.</para> - <para>To set custom DV timings for the device, applications use the -&VIDIOC-S-DV-TIMINGS; ioctl and to get current custom DV timings they use the -&VIDIOC-G-DV-TIMINGS; ioctl.</para> +&VIDIOC-S-DV-PRESET; ioctl. To detect the preset as seen by the video receiver applications +use the &VIDIOC-QUERY-DV-PRESET; ioctl.</para> <para>Applications can make use of the <xref linkend="input-capabilities" /> and <xref linkend="output-capabilities"/> flags to decide what ioctls are available to set the video timings for the device.</para> - </section> </section> &sub-controls; diff --git a/Documentation/DocBook/media/v4l/compat.xml b/Documentation/DocBook/media/v4l/compat.xml index bce97c50391b..ea42ef824948 100644 --- a/Documentation/DocBook/media/v4l/compat.xml +++ b/Documentation/DocBook/media/v4l/compat.xml @@ -2407,6 +2407,54 @@ details.</para> <para>Added <link linkend="jpeg-controls">JPEG compression control class</link>.</para> </listitem> + <listitem> + <para>Extended the DV Timings API: + &VIDIOC-ENUM-DV-TIMINGS;, &VIDIOC-QUERY-DV-TIMINGS; and + &VIDIOC-DV-TIMINGS-CAP;.</para> + </listitem> + </orderedlist> + </section> + + <section> + <title>V4L2 in Linux 3.5</title> + <orderedlist> + <listitem> + <para>Added integer menus, the new type will be + V4L2_CTRL_TYPE_INTEGER_MENU.</para> + </listitem> + <listitem> + <para>Added selection API for V4L2 subdev interface: + &VIDIOC-SUBDEV-G-SELECTION; and + &VIDIOC-SUBDEV-S-SELECTION;.</para> + </listitem> + <listitem> + <para> Added <constant>V4L2_COLORFX_ANTIQUE</constant>, + <constant>V4L2_COLORFX_ART_FREEZE</constant>, + <constant>V4L2_COLORFX_AQUA</constant>, + <constant>V4L2_COLORFX_SILHOUETTE</constant>, + <constant>V4L2_COLORFX_SOLARIZATION</constant>, + <constant>V4L2_COLORFX_VIVID</constant> and + <constant>V4L2_COLORFX_ARBITRARY_CBCR</constant> menu items + to the <constant>V4L2_CID_COLORFX</constant> control.</para> + </listitem> + <listitem> + <para> Added <constant>V4L2_CID_COLORFX_CBCR</constant> control.</para> + </listitem> + <listitem> + <para> Added camera controls <constant>V4L2_CID_AUTO_EXPOSURE_BIAS</constant>, + <constant>V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE</constant>, + <constant>V4L2_CID_IMAGE_STABILIZATION</constant>, + <constant>V4L2_CID_ISO_SENSITIVITY</constant>, + <constant>V4L2_CID_ISO_SENSITIVITY_AUTO</constant>, + <constant>V4L2_CID_EXPOSURE_METERING</constant>, + <constant>V4L2_CID_SCENE_MODE</constant>, + <constant>V4L2_CID_3A_LOCK</constant>, + <constant>V4L2_CID_AUTO_FOCUS_START</constant>, + <constant>V4L2_CID_AUTO_FOCUS_STOP</constant>, + <constant>V4L2_CID_AUTO_FOCUS_STATUS</constant> and + <constant>V4L2_CID_AUTO_FOCUS_RANGE</constant>. + </para> + </listitem> </orderedlist> </section> @@ -2508,6 +2556,10 @@ and may change in the future.</para> ioctls.</para> </listitem> <listitem> + <para>&VIDIOC-DECODER-CMD; and &VIDIOC-TRY-DECODER-CMD; +ioctls.</para> + </listitem> + <listitem> <para>&VIDIOC-DBG-G-REGISTER; and &VIDIOC-DBG-S-REGISTER; ioctls.</para> </listitem> @@ -2515,6 +2567,10 @@ ioctls.</para> <para>&VIDIOC-DBG-G-CHIP-IDENT; ioctl.</para> </listitem> <listitem> + <para>&VIDIOC-ENUM-DV-TIMINGS;, &VIDIOC-QUERY-DV-TIMINGS; and + &VIDIOC-DV-TIMINGS-CAP; ioctls.</para> + </listitem> + <listitem> <para>Flash API. <xref linkend="flash-controls" /></para> </listitem> <listitem> @@ -2523,6 +2579,14 @@ ioctls.</para> <listitem> <para>Selection API. <xref linkend="selection-api" /></para> </listitem> + <listitem> + <para>Sub-device selection API: &VIDIOC-SUBDEV-G-SELECTION; + and &VIDIOC-SUBDEV-S-SELECTION; ioctls.</para> + </listitem> + <listitem> + <para><link linkend="v4l2-auto-focus-area"><constant> + V4L2_CID_AUTO_FOCUS_AREA</constant></link> control.</para> + </listitem> </itemizedlist> </section> @@ -2538,6 +2602,17 @@ interfaces and should not be implemented in new drivers.</para> <constant>VIDIOC_S_MPEGCOMP</constant> ioctls. Use Extended Controls, <xref linkend="extended-controls" />.</para> </listitem> + <listitem> + <para>&VIDIOC-G-DV-PRESET;, &VIDIOC-S-DV-PRESET;, &VIDIOC-ENUM-DV-PRESETS; and + &VIDIOC-QUERY-DV-PRESET; ioctls. Use the DV Timings API (<xref linkend="dv-timings" />).</para> + </listitem> + <listitem> + <para><constant>VIDIOC_SUBDEV_G_CROP</constant> and + <constant>VIDIOC_SUBDEV_S_CROP</constant> ioctls. Use + <constant>VIDIOC_SUBDEV_G_SELECTION</constant> and + <constant>VIDIOC_SUBDEV_S_SELECTION</constant>, <xref + linkend="vidioc-subdev-g-selection" />.</para> + </listitem> </itemizedlist> </section> </section> diff --git a/Documentation/DocBook/media/v4l/controls.xml b/Documentation/DocBook/media/v4l/controls.xml index dd03cf4a6539..676bc46f9c52 100644 --- a/Documentation/DocBook/media/v4l/controls.xml +++ b/Documentation/DocBook/media/v4l/controls.xml @@ -285,18 +285,92 @@ minimum value disables backlight compensation.</entry> <row id="v4l2-colorfx"> <entry><constant>V4L2_CID_COLORFX</constant></entry> <entry>enum</entry> - <entry>Selects a color effect. Possible values for -<constant>enum v4l2_colorfx</constant> are: -<constant>V4L2_COLORFX_NONE</constant> (0), -<constant>V4L2_COLORFX_BW</constant> (1), -<constant>V4L2_COLORFX_SEPIA</constant> (2), -<constant>V4L2_COLORFX_NEGATIVE</constant> (3), -<constant>V4L2_COLORFX_EMBOSS</constant> (4), -<constant>V4L2_COLORFX_SKETCH</constant> (5), -<constant>V4L2_COLORFX_SKY_BLUE</constant> (6), -<constant>V4L2_COLORFX_GRASS_GREEN</constant> (7), -<constant>V4L2_COLORFX_SKIN_WHITEN</constant> (8) and -<constant>V4L2_COLORFX_VIVID</constant> (9).</entry> + <entry>Selects a color effect. The following values are defined: + </entry> + </row><row> + <entry></entry> + <entry></entry> + <entrytbl spanname="descr" cols="2"> + <tbody valign="top"> + <row> + <entry><constant>V4L2_COLORFX_NONE</constant> </entry> + <entry>Color effect is disabled.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_ANTIQUE</constant> </entry> + <entry>An aging (old photo) effect.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_ART_FREEZE</constant> </entry> + <entry>Frost color effect.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_AQUA</constant> </entry> + <entry>Water color, cool tone.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_BW</constant> </entry> + <entry>Black and white.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_EMBOSS</constant> </entry> + <entry>Emboss, the highlights and shadows replace light/dark boundaries + and low contrast areas are set to a gray background.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_GRASS_GREEN</constant> </entry> + <entry>Grass green.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_NEGATIVE</constant> </entry> + <entry>Negative.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_SEPIA</constant> </entry> + <entry>Sepia tone.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_SKETCH</constant> </entry> + <entry>Sketch.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_SKIN_WHITEN</constant> </entry> + <entry>Skin whiten.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_SKY_BLUE</constant> </entry> + <entry>Sky blue.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_SOLARIZATION</constant> </entry> + <entry>Solarization, the image is partially reversed in tone, + only color values above or below a certain threshold are inverted. + </entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_SILHOUETTE</constant> </entry> + <entry>Silhouette (outline).</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_VIVID</constant> </entry> + <entry>Vivid colors.</entry> + </row> + <row> + <entry><constant>V4L2_COLORFX_SET_CBCR</constant> </entry> + <entry>The Cb and Cr chroma components are replaced by fixed + coefficients determined by <constant>V4L2_CID_COLORFX_CBCR</constant> + control.</entry> + </row> + </tbody> + </entrytbl> + </row> + <row> + <entry><constant>V4L2_CID_COLORFX_CBCR</constant></entry> + <entry>integer</entry> + <entry>Determines the Cb and Cr coefficients for <constant>V4L2_COLORFX_SET_CBCR</constant> + color effect. Bits [7:0] of the supplied 32 bit value are interpreted as + Cr component, bits [15:8] as Cb component and bits [31:16] must be zero. + </entry> </row> <row> <entry><constant>V4L2_CID_ROTATE</constant></entry> @@ -2775,6 +2849,51 @@ remain constant.</entry> <row><entry></entry></row> <row> + <entry spanname="id"><constant>V4L2_CID_EXPOSURE_BIAS</constant> </entry> + <entry>integer menu</entry> + </row><row><entry spanname="descr"> Determines the automatic +exposure compensation, it is effective only when <constant>V4L2_CID_EXPOSURE_AUTO</constant> +control is set to <constant>AUTO</constant>, <constant>SHUTTER_PRIORITY </constant> +or <constant>APERTURE_PRIORITY</constant>. +It is expressed in terms of EV, drivers should interpret the values as 0.001 EV +units, where the value 1000 stands for +1 EV. +<para>Increasing the exposure compensation value is equivalent to decreasing +the exposure value (EV) and will increase the amount of light at the image +sensor. The camera performs the exposure compensation by adjusting absolute +exposure time and/or aperture.</para></entry> + </row> + <row><entry></entry></row> + + <row id="v4l2-exposure-metering"> + <entry spanname="id"><constant>V4L2_CID_EXPOSURE_METERING</constant> </entry> + <entry>enum v4l2_exposure_metering</entry> + </row><row><entry spanname="descr">Determines how the camera measures +the amount of light available for the frame exposure. Possible values are:</entry> + </row> + <row> + <entrytbl spanname="descr" cols="2"> + <tbody valign="top"> + <row> + <entry><constant>V4L2_EXPOSURE_METERING_AVERAGE</constant> </entry> + <entry>Use the light information coming from the entire frame +and average giving no weighting to any particular portion of the metered area. + </entry> + </row> + <row> + <entry><constant>V4L2_EXPOSURE_METERING_CENTER_WEIGHTED</constant> </entry> + <entry>Average the light information coming from the entire frame +giving priority to the center of the metered area.</entry> + </row> + <row> + <entry><constant>V4L2_EXPOSURE_METERING_SPOT</constant> </entry> + <entry>Measure only very small area at the center of the frame.</entry> + </row> + </tbody> + </entrytbl> + </row> + <row><entry></entry></row> + + <row> <entry spanname="id"><constant>V4L2_CID_PAN_RELATIVE</constant> </entry> <entry>integer</entry> </row><row><entry spanname="descr">This control turns the @@ -2857,13 +2976,107 @@ negative values towards infinity. This is a write-only control.</entry> <row> <entry spanname="id"><constant>V4L2_CID_FOCUS_AUTO</constant> </entry> <entry>boolean</entry> - </row><row><entry spanname="descr">Enables automatic focus -adjustments. The effect of manual focus adjustments while this feature + </row><row><entry spanname="descr">Enables continuous automatic +focus adjustments. The effect of manual focus adjustments while this feature is enabled is undefined, drivers should ignore such requests.</entry> </row> <row><entry></entry></row> <row> + <entry spanname="id"><constant>V4L2_CID_AUTO_FOCUS_START</constant> </entry> + <entry>button</entry> + </row><row><entry spanname="descr">Starts single auto focus process. +The effect of setting this control when <constant>V4L2_CID_FOCUS_AUTO</constant> +is set to <constant>TRUE</constant> (1) is undefined, drivers should ignore +such requests.</entry> + </row> + <row><entry></entry></row> + + <row> + <entry spanname="id"><constant>V4L2_CID_AUTO_FOCUS_STOP</constant> </entry> + <entry>button</entry> + </row><row><entry spanname="descr">Aborts automatic focusing +started with <constant>V4L2_CID_AUTO_FOCUS_START</constant> control. It is +effective only when the continuous autofocus is disabled, that is when +<constant>V4L2_CID_FOCUS_AUTO</constant> control is set to <constant>FALSE +</constant> (0).</entry> + </row> + <row><entry></entry></row> + + <row id="v4l2-auto-focus-status"> + <entry spanname="id"> + <constant>V4L2_CID_AUTO_FOCUS_STATUS</constant> </entry> + <entry>bitmask</entry> + </row> + <row><entry spanname="descr">The automatic focus status. This is a read-only + control.</entry> + </row> + <row> + <entrytbl spanname="descr" cols="2"> + <tbody valign="top"> + <row> + <entry><constant>V4L2_AUTO_FOCUS_STATUS_IDLE</constant> </entry> + <entry>Automatic focus is not active.</entry> + </row> + <row> + <entry><constant>V4L2_AUTO_FOCUS_STATUS_BUSY</constant> </entry> + <entry>Automatic focusing is in progress.</entry> + </row> + <row> + <entry><constant>V4L2_AUTO_FOCUS_STATUS_REACHED</constant> </entry> + <entry>Focus has been reached.</entry> + </row> + <row> + <entry><constant>V4L2_AUTO_FOCUS_STATUS_FAILED</constant> </entry> + <entry>Automatic focus has failed, the driver will not + transition from this state until another action is + performed by an application.</entry> + </row> + </tbody> + </entrytbl> + </row> + <row><entry spanname="descr"> +Setting <constant>V4L2_LOCK_FOCUS</constant> lock bit of the <constant>V4L2_CID_3A_LOCK +</constant> control may stop updates of the <constant>V4L2_CID_AUTO_FOCUS_STATUS</constant> +control value.</entry> + </row> + <row><entry></entry></row> + + <row id="v4l2-auto-focus-range"> + <entry spanname="id"> + <constant>V4L2_CID_AUTO_FOCUS_RANGE</constant> </entry> + <entry>enum v4l2_auto_focus_range</entry> + </row> + <row><entry spanname="descr">Determines auto focus distance range +for which lens may be adjusted. </entry> + </row> + <row> + <entrytbl spanname="descr" cols="2"> + <tbody valign="top"> + <row> + <entry><constant>V4L2_AUTO_FOCUS_RANGE_AUTO</constant> </entry> + <entry>The camera automatically selects the focus range.</entry> + </row> + <row> + <entry><constant>V4L2_AUTO_FOCUS_RANGE_NORMAL</constant> </entry> + <entry>Normal distance range, limited for best automatic focus +performance.</entry> + </row> + <row> + <entry><constant>V4L2_AUTO_FOCUS_RANGE_MACRO</constant> </entry> + <entry>Macro (close-up) auto focus. The camera will +use its minimum possible distance for auto focus.</entry> + </row> + <row> + <entry><constant>V4L2_AUTO_FOCUS_RANGE_INFINITY</constant> </entry> + <entry>The lens is set to focus on an object at infinite distance.</entry> + </row> + </tbody> + </entrytbl> + </row> + <row><entry></entry></row> + + <row> <entry spanname="id"><constant>V4L2_CID_ZOOM_ABSOLUTE</constant> </entry> <entry>integer</entry> </row><row><entry spanname="descr">Specify the objective lens @@ -2932,6 +3145,295 @@ camera sensor on or off, or specify its strength. Such band-stop filters can be used, for example, to filter out the fluorescent light component.</entry> </row> <row><entry></entry></row> + + <row id="v4l2-auto-n-preset-white-balance"> + <entry spanname="id"><constant>V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE</constant> </entry> + <entry>enum v4l2_auto_n_preset_white_balance</entry> + </row><row><entry spanname="descr">Sets white balance to automatic, +manual or a preset. The presets determine color temperature of the light as +a hint to the camera for white balance adjustments resulting in most accurate +color representation. The following white balance presets are listed in order +of increasing color temperature.</entry> + </row> + <row> + <entrytbl spanname="descr" cols="2"> + <tbody valign="top"> + <row> + <entry><constant>V4L2_WHITE_BALANCE_MANUAL</constant> </entry> + <entry>Manual white balance.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_AUTO</constant> </entry> + <entry>Automatic white balance adjustments.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_INCANDESCENT</constant> </entry> + <entry>White balance setting for incandescent (tungsten) lighting. +It generally cools down the colors and corresponds approximately to 2500...3500 K +color temperature range.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_FLUORESCENT</constant> </entry> + <entry>White balance preset for fluorescent lighting. +It corresponds approximately to 4000...5000 K color temperature.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_FLUORESCENT_H</constant> </entry> + <entry>With this setting the camera will compensate for +fluorescent H lighting.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_HORIZON</constant> </entry> + <entry>White balance setting for horizon daylight. +It corresponds approximately to 5000 K color temperature.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_DAYLIGHT</constant> </entry> + <entry>White balance preset for daylight (with clear sky). +It corresponds approximately to 5000...6500 K color temperature.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_FLASH</constant> </entry> + <entry>With this setting the camera will compensate for the flash +light. It slightly warms up the colors and corresponds roughly to 5000...5500 K +color temperature.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_CLOUDY</constant> </entry> + <entry>White balance preset for moderately overcast sky. +This option corresponds approximately to 6500...8000 K color temperature +range.</entry> + </row> + <row> + <entry><constant>V4L2_WHITE_BALANCE_SHADE</constant> </entry> + <entry>White balance preset for shade or heavily overcast +sky. It corresponds approximately to 9000...10000 K color temperature. +</entry> + </row> + </tbody> + </entrytbl> + </row> + <row><entry></entry></row> + + <row id="v4l2-wide-dynamic-range"> + <entry spanname="id"><constant>V4L2_CID_WIDE_DYNAMIC_RANGE</constant></entry> + <entry>boolean</entry> + </row> + <row> + <entry spanname="descr">Enables or disables the camera's wide dynamic +range feature. This feature allows to obtain clear images in situations where +intensity of the illumination varies significantly throughout the scene, i.e. +there are simultaneously very dark and very bright areas. It is most commonly +realized in cameras by combining two subsequent frames with different exposure +times. <footnote id="ctypeconv"><para> This control may be changed to a menu +control in the future, if more options are required.</para></footnote></entry> + </row> + <row><entry></entry></row> + + <row id="v4l2-image-stabilization"> + <entry spanname="id"><constant>V4L2_CID_IMAGE_STABILIZATION</constant></entry> + <entry>boolean</entry> + </row> + <row> + <entry spanname="descr">Enables or disables image stabilization. + <footnoteref linkend="ctypeconv"/></entry> + </row> + <row><entry></entry></row> + + <row> + <entry spanname="id"><constant>V4L2_CID_ISO_SENSITIVITY</constant> </entry> + <entry>integer menu</entry> + </row><row><entry spanname="descr">Determines ISO equivalent of an +image sensor indicating the sensor's sensitivity to light. The numbers are +expressed in arithmetic scale, as per <xref linkend="iso12232" /> standard, +where doubling the sensor sensitivity is represented by doubling the numerical +ISO value. Applications should interpret the values as standard ISO values +multiplied by 1000, e.g. control value 800 stands for ISO 0.8. Drivers will +usually support only a subset of standard ISO values. The effect of setting +this control while the <constant>V4L2_CID_ISO_SENSITIVITY_AUTO</constant> +control is set to a value other than <constant>V4L2_CID_ISO_SENSITIVITY_MANUAL +</constant> is undefined, drivers should ignore such requests.</entry> + </row> + <row><entry></entry></row> + + <row id="v4l2-iso-sensitivity-auto-type"> + <entry spanname="id"><constant>V4L2_CID_ISO_SENSITIVITY_AUTO</constant> </entry> + <entry>enum v4l2_iso_sensitivity_type</entry> + </row><row><entry spanname="descr">Enables or disables automatic ISO +sensitivity adjustments.</entry> + </row> + <row> + <entrytbl spanname="descr" cols="2"> + <tbody valign="top"> + <row> + <entry><constant>V4L2_CID_ISO_SENSITIVITY_MANUAL</constant> </entry> + <entry>Manual ISO sensitivity.</entry> + </row> + <row> + <entry><constant>V4L2_CID_ISO_SENSITIVITY_AUTO</constant> </entry> + <entry>Automatic ISO sensitivity adjustments.</entry> + </row> + </tbody> + </entrytbl> + </row> + <row><entry></entry></row> + + <row id="v4l2-scene-mode"> + <entry spanname="id"><constant>V4L2_CID_SCENE_MODE</constant> </entry> + <entry>enum v4l2_scene_mode</entry> + </row><row><entry spanname="descr">This control allows to select +scene programs as the camera automatic modes optimized for common shooting +scenes. Within these modes the camera determines best exposure, aperture, +focusing, light metering, white balance and equivalent sensitivity. The +controls of those parameters are influenced by the scene mode control. +An exact behavior in each mode is subject to the camera specification. + +<para>When the scene mode feature is not used, this control should be set to +<constant>V4L2_SCENE_MODE_NONE</constant> to make sure the other possibly +related controls are accessible. The following scene programs are defined: +</para> +</entry> + </row> + <row> + <entrytbl spanname="descr" cols="2"> + <tbody valign="top"> + <row> + <entry><constant>V4L2_SCENE_MODE_NONE</constant> </entry> + <entry>The scene mode feature is disabled.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_BACKLIGHT</constant> </entry> + <entry>Backlight. Compensates for dark shadows when light is + coming from behind a subject, also by automatically turning + on the flash.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_BEACH_SNOW</constant> </entry> + <entry>Beach and snow. This mode compensates for all-white or +bright scenes, which tend to look gray and low contrast, when camera's automatic +exposure is based on an average scene brightness. To compensate, this mode +automatically slightly overexposes the frames. The white balance may also be +adjusted to compensate for the fact that reflected snow looks bluish rather +than white.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_CANDLELIGHT</constant> </entry> + <entry>Candle light. The camera generally raises the ISO +sensitivity and lowers the shutter speed. This mode compensates for relatively +close subject in the scene. The flash is disabled in order to preserve the +ambiance of the light.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_DAWN_DUSK</constant> </entry> + <entry>Dawn and dusk. Preserves the colors seen in low +natural light before dusk and after down. The camera may turn off the flash, +and automatically focus at infinity. It will usually boost saturation and +lower the shutter speed.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_FALL_COLORS</constant> </entry> + <entry>Fall colors. Increases saturation and adjusts white +balance for color enhancement. Pictures of autumn leaves get saturated reds +and yellows.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_FIREWORKS</constant> </entry> + <entry>Fireworks. Long exposure times are used to capture +the expanding burst of light from a firework. The camera may invoke image +stabilization.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_LANDSCAPE</constant> </entry> + <entry>Landscape. The camera may choose a small aperture to +provide deep depth of field and long exposure duration to help capture detail +in dim light conditions. The focus is fixed at infinity. Suitable for distant +and wide scenery.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_NIGHT</constant> </entry> + <entry>Night, also known as Night Landscape. Designed for low +light conditions, it preserves detail in the dark areas without blowing out bright +objects. The camera generally sets itself to a medium-to-high ISO sensitivity, +with a relatively long exposure time, and turns flash off. As such, there will be +increased image noise and the possibility of blurred image.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_PARTY_INDOOR</constant> </entry> + <entry>Party and indoor. Designed to capture indoor scenes +that are lit by indoor background lighting as well as the flash. The camera +usually increases ISO sensitivity, and adjusts exposure for the low light +conditions.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_PORTRAIT</constant> </entry> + <entry>Portrait. The camera adjusts the aperture so that the +depth of field is reduced, which helps to isolate the subject against a smooth +background. Most cameras recognize the presence of faces in the scene and focus +on them. The color hue is adjusted to enhance skin tones. The intensity of the +flash is often reduced.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_SPORTS</constant> </entry> + <entry>Sports. Significantly increases ISO and uses a fast +shutter speed to freeze motion of rapidly-moving subjects. Increased image +noise may be seen in this mode.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_SUNSET</constant> </entry> + <entry>Sunset. Preserves deep hues seen in sunsets and +sunrises. It bumps up the saturation.</entry> + </row> + <row> + <entry><constant>V4L2_SCENE_MODE_TEXT</constant> </entry> + <entry>Text. It applies extra contrast and sharpness, it is +typically a black-and-white mode optimized for readability. Automatic focus +may be switched to close-up mode and this setting may also involve some +lens-distortion correction.</entry> + </row> + </tbody> + </entrytbl> + </row> + <row><entry></entry></row> + + <row> + <entry spanname="id"><constant>V4L2_CID_3A_LOCK</constant></entry> + <entry>bitmask</entry> + </row> + <row> + <entry spanname="descr">This control locks or unlocks the automatic +focus, exposure and white balance. The automatic adjustments can be paused +independently by setting the corresponding lock bit to 1. The camera then retains +the settings until the lock bit is cleared. The following lock bits are defined: +</entry> + </row> + <row> + <entrytbl spanname="descr" cols="2"> + <tbody valign="top"> + <row> + <entry><constant>V4L2_LOCK_EXPOSURE</constant></entry> + <entry>Automatic exposure adjustments lock.</entry> + </row> + <row> + <entry><constant>V4L2_LOCK_WHITE_BALANCE</constant></entry> + <entry>Automatic white balance adjustments lock.</entry> + </row> + <row> + <entry><constant>V4L2_LOCK_FOCUS</constant></entry> + <entry>Automatic focus lock.</entry> + </row> + </tbody> + </entrytbl> + </row> + <row><entry spanname="descr"> +When a given algorithm is not enabled, drivers should ignore requests +to lock it and should return no error. An example might be an application +setting bit <constant>V4L2_LOCK_WHITE_BALANCE</constant> when the +<constant>V4L2_CID_AUTO_WHITE_BALANCE</constant> control is set to +<constant>FALSE</constant>. The value of this control may be changed +by exposure, white balance or focus controls.</entry> + </row> + <row><entry></entry></row> + </tbody> </tgroup> </table> @@ -3476,7 +3978,7 @@ interface and may change in the future.</para> <entry spanname="id"><constant>V4L2_CID_JPEG_CHROMA_SUBSAMPLING</constant></entry> <entry>menu</entry> </row> - <row id="jpeg-chroma-subsampling-control"> + <row id="v4l2-jpeg-chroma-subsampling"> <entry spanname="descr">The chroma subsampling factors describe how each component of an input image is sampled, in respect to maximum sample rate in each spatial dimension. See <xref linkend="itu-t81"/>, @@ -3486,7 +3988,7 @@ interface and may change in the future.</para> from RGB to Y'CbCr color space. </entry> </row> - <row> + <row id = "v4l2-jpeg-chroma-subsampling"> <entrytbl spanname="descr" cols="2"> <tbody valign="top"> <row> @@ -3538,12 +4040,12 @@ interface and may change in the future.</para> </entry> </row> <row id="jpeg-quality-control"> - <entry spanname="id"><constant>V4L2_CID_JPEG_COMPRESION_QUALITY</constant></entry> + <entry spanname="id"><constant>V4L2_CID_JPEG_COMPRESSION_QUALITY</constant></entry> <entry>integer</entry> </row> <row> <entry spanname="descr"> - <constant>V4L2_CID_JPEG_COMPRESION_QUALITY</constant> control + <constant>V4L2_CID_JPEG_COMPRESSION_QUALITY</constant> control determines trade-off between image quality and size. It provides simpler method for applications to control image quality, without a need for direct reconfiguration of luminance and chrominance @@ -3551,7 +4053,7 @@ interface and may change in the future.</para> In cases where a driver uses quantization tables configured directly by an application, using interfaces defined elsewhere, <constant> - V4L2_CID_JPEG_COMPRESION_QUALITY</constant> control should be set + V4L2_CID_JPEG_COMPRESSION_QUALITY</constant> control should be set by driver to 0. <para>The value range of this control is driver-specific. Only @@ -3599,4 +4101,172 @@ interface and may change in the future.</para> to <xref linkend="itu-t81"/>, <xref linkend="jfif"/>, <xref linkend="w3c-jpeg-jfif"/>.</para> </section> + + <section id="image-source-controls"> + <title>Image Source Control Reference</title> + + <note> + <title>Experimental</title> + + <para>This is an <link + linkend="experimental">experimental</link> interface and may + change in the future.</para> + </note> + + <para> + The Image Source control class is intended for low-level + control of image source devices such as image sensors. The + devices feature an analogue to digital converter and a bus + transmitter to transmit the image data out of the device. + </para> + + <table pgwide="1" frame="none" id="image-source-control-id"> + <title>Image Source Control IDs</title> + + <tgroup cols="4"> + <colspec colname="c1" colwidth="1*" /> + <colspec colname="c2" colwidth="6*" /> + <colspec colname="c3" colwidth="2*" /> + <colspec colname="c4" colwidth="6*" /> + <spanspec namest="c1" nameend="c2" spanname="id" /> + <spanspec namest="c2" nameend="c4" spanname="descr" /> + <thead> + <row> + <entry spanname="id" align="left">ID</entry> + <entry align="left">Type</entry> + </row><row rowsep="1"><entry spanname="descr" align="left">Description</entry> + </row> + </thead> + <tbody valign="top"> + <row><entry></entry></row> + <row> + <entry spanname="id"><constant>V4L2_CID_IMAGE_SOURCE_CLASS</constant></entry> + <entry>class</entry> + </row> + <row> + <entry spanname="descr">The IMAGE_SOURCE class descriptor.</entry> + </row> + <row> + <entry spanname="id"><constant>V4L2_CID_VBLANK</constant></entry> + <entry>integer</entry> + </row> + <row> + <entry spanname="descr">Vertical blanking. The idle period + after every frame during which no image data is produced. + The unit of vertical blanking is a line. Every line has + length of the image width plus horizontal blanking at the + pixel rate defined by + <constant>V4L2_CID_PIXEL_RATE</constant> control in the + same sub-device.</entry> + </row> + <row> + <entry spanname="id"><constant>V4L2_CID_HBLANK</constant></entry> + <entry>integer</entry> + </row> + <row> + <entry spanname="descr">Horizontal blanking. The idle + period after every line of image data during which no + image data is produced. The unit of horizontal blanking is + pixels.</entry> + </row> + <row> + <entry spanname="id"><constant>V4L2_CID_ANALOGUE_GAIN</constant></entry> + <entry>integer</entry> + </row> + <row> + <entry spanname="descr">Analogue gain is gain affecting + all colour components in the pixel matrix. The gain + operation is performed in the analogue domain before A/D + conversion. + </entry> + </row> + <row><entry></entry></row> + </tbody> + </tgroup> + </table> + + </section> + + <section id="image-process-controls"> + <title>Image Process Control Reference</title> + + <note> + <title>Experimental</title> + + <para>This is an <link + linkend="experimental">experimental</link> interface and may + change in the future.</para> + </note> + + <para> + The Image Source control class is intended for low-level control of + image processing functions. Unlike + <constant>V4L2_CID_IMAGE_SOURCE_CLASS</constant>, the controls in + this class affect processing the image, and do not control capturing + of it. + </para> + + <table pgwide="1" frame="none" id="image-process-control-id"> + <title>Image Source Control IDs</title> + + <tgroup cols="4"> + <colspec colname="c1" colwidth="1*" /> + <colspec colname="c2" colwidth="6*" /> + <colspec colname="c3" colwidth="2*" /> + <colspec colname="c4" colwidth="6*" /> + <spanspec namest="c1" nameend="c2" spanname="id" /> + <spanspec namest="c2" nameend="c4" spanname="descr" /> + <thead> + <row> + <entry spanname="id" align="left">ID</entry> + <entry align="left">Type</entry> + </row><row rowsep="1"><entry spanname="descr" align="left">Description</entry> + </row> + </thead> + <tbody valign="top"> + <row><entry></entry></row> + <row> + <entry spanname="id"><constant>V4L2_CID_IMAGE_PROC_CLASS</constant></entry> + <entry>class</entry> + </row> + <row> + <entry spanname="descr">The IMAGE_PROC class descriptor.</entry> + </row> + <row> + <entry spanname="id"><constant>V4L2_CID_LINK_FREQ</constant></entry> + <entry>integer menu</entry> + </row> + <row> + <entry spanname="descr">Data bus frequency. Together with the + media bus pixel code, bus type (clock cycles per sample), the + data bus frequency defines the pixel rate + (<constant>V4L2_CID_PIXEL_RATE</constant>) in the + pixel array (or possibly elsewhere, if the device is not an + image sensor). The frame rate can be calculated from the pixel + clock, image width and height and horizontal and vertical + blanking. While the pixel rate control may be defined elsewhere + than in the subdev containing the pixel array, the frame rate + cannot be obtained from that information. This is because only + on the pixel array it can be assumed that the vertical and + horizontal blanking information is exact: no other blanking is + allowed in the pixel array. The selection of frame rate is + performed by selecting the desired horizontal and vertical + blanking. The unit of this control is Hz. </entry> + </row> + <row> + <entry spanname="id"><constant>V4L2_CID_PIXEL_RATE</constant></entry> + <entry>64-bit integer</entry> + </row> + <row> + <entry spanname="descr">Pixel rate in the source pads of + the subdev. This control is read-only and its unit is + pixels / second. + </entry> + </row> + <row><entry></entry></row> + </tbody> + </tgroup> + </table> + + </section> </section> diff --git a/Documentation/DocBook/media/v4l/dev-subdev.xml b/Documentation/DocBook/media/v4l/dev-subdev.xml index 0916a7343a16..4afcbbec5eda 100644 --- a/Documentation/DocBook/media/v4l/dev-subdev.xml +++ b/Documentation/DocBook/media/v4l/dev-subdev.xml @@ -76,11 +76,12 @@ <wordasword>format</wordasword> means the combination of media bus data format, frame width and frame height.</para></note> - <para>Image formats are typically negotiated on video capture and output - devices using the <link linkend="crop">cropping and scaling</link> ioctls. - The driver is responsible for configuring every block in the video pipeline - according to the requested format at the pipeline input and/or - output.</para> + <para>Image formats are typically negotiated on video capture and + output devices using the format and <link + linkend="vidioc-subdev-g-selection">selection</link> ioctls. The + driver is responsible for configuring every block in the video + pipeline according to the requested format at the pipeline input + and/or output.</para> <para>For complex devices, such as often found in embedded systems, identical image sizes at the output of a pipeline can be achieved using @@ -276,11 +277,11 @@ </section> <section> - <title>Cropping and scaling</title> + <title>Selections: cropping, scaling and composition</title> <para>Many sub-devices support cropping frames on their input or output pads (or possible even on both). Cropping is used to select the area of - interest in an image, typically on a video sensor or video decoder. It can + interest in an image, typically on an image sensor or a video decoder. It can also be used as part of digital zoom implementations to select the area of the image that will be scaled up.</para> @@ -288,26 +289,179 @@ &v4l2-rect; by the coordinates of the top left corner and the rectangle size. Both the coordinates and sizes are expressed in pixels.</para> - <para>The crop rectangle is retrieved and set using the - &VIDIOC-SUBDEV-G-CROP; and &VIDIOC-SUBDEV-S-CROP; ioctls. Like for pad - formats, drivers store try and active crop rectangles. The format - negotiation mechanism applies to crop settings as well.</para> - - <para>On input pads, cropping is applied relatively to the current pad - format. The pad format represents the image size as received by the - sub-device from the previous block in the pipeline, and the crop rectangle - represents the sub-image that will be transmitted further inside the - sub-device for processing. The crop rectangle be entirely containted - inside the input image size.</para> - - <para>Input crop rectangle are reset to their default value when the input - image format is modified. Drivers should use the input image size as the - crop rectangle default value, but hardware requirements may prevent this. - </para> + <para>As for pad formats, drivers store try and active + rectangles for the selection targets of ACTUAL type <xref + linkend="v4l2-subdev-selection-targets">.</xref></para> + + <para>On sink pads, cropping is applied relative to the + current pad format. The pad format represents the image size as + received by the sub-device from the previous block in the + pipeline, and the crop rectangle represents the sub-image that + will be transmitted further inside the sub-device for + processing.</para> + + <para>The scaling operation changes the size of the image by + scaling it to new dimensions. The scaling ratio isn't specified + explicitly, but is implied from the original and scaled image + sizes. Both sizes are represented by &v4l2-rect;.</para> + + <para>Scaling support is optional. When supported by a subdev, + the crop rectangle on the subdev's sink pad is scaled to the + size configured using the &VIDIOC-SUBDEV-S-SELECTION; IOCTL + using <constant>V4L2_SUBDEV_SEL_COMPOSE_ACTUAL</constant> + selection target on the same pad. If the subdev supports scaling + but not composing, the top and left values are not used and must + always be set to zero.</para> + + <para>On source pads, cropping is similar to sink pads, with the + exception that the source size from which the cropping is + performed, is the COMPOSE rectangle on the sink pad. In both + sink and source pads, the crop rectangle must be entirely + contained inside the source image size for the crop + operation.</para> + + <para>The drivers should always use the closest possible + rectangle the user requests on all selection targets, unless + specifically told otherwise. + <constant>V4L2_SUBDEV_SEL_FLAG_SIZE_GE</constant> and + <constant>V4L2_SUBDEV_SEL_FLAG_SIZE_LE</constant> flags may be + used to round the image size either up or down. <xref + linkend="v4l2-subdev-selection-flags"></xref></para> + </section> + + <section> + <title>Types of selection targets</title> + + <section> + <title>ACTUAL targets</title> + + <para>ACTUAL targets reflect the actual hardware configuration + at any point of time. There is a BOUNDS target + corresponding to every ACTUAL.</para> + </section> + + <section> + <title>BOUNDS targets</title> + + <para>BOUNDS targets is the smallest rectangle that contains + all valid ACTUAL rectangles. It may not be possible to set the + ACTUAL rectangle as large as the BOUNDS rectangle, however. + This may be because e.g. a sensor's pixel array is not + rectangular but cross-shaped or round. The maximum size may + also be smaller than the BOUNDS rectangle.</para> + </section> - <para>Cropping behaviour on output pads is not defined.</para> + </section> + + <section> + <title>Order of configuration and format propagation</title> + + <para>Inside subdevs, the order of image processing steps will + always be from the sink pad towards the source pad. This is also + reflected in the order in which the configuration must be + performed by the user: the changes made will be propagated to + any subsequent stages. If this behaviour is not desired, the + user must set + <constant>V4L2_SUBDEV_SEL_FLAG_KEEP_CONFIG</constant> flag. This + flag causes no propagation of the changes are allowed in any + circumstances. This may also cause the accessed rectangle to be + adjusted by the driver, depending on the properties of the + underlying hardware.</para> + + <para>The coordinates to a step always refer to the actual size + of the previous step. The exception to this rule is the source + compose rectangle, which refers to the sink compose bounds + rectangle --- if it is supported by the hardware.</para> + + <orderedlist> + <listitem>Sink pad format. The user configures the sink pad + format. This format defines the parameters of the image the + entity receives through the pad for further processing.</listitem> + + <listitem>Sink pad actual crop selection. The sink pad crop + defines the crop performed to the sink pad format.</listitem> + + <listitem>Sink pad actual compose selection. The size of the + sink pad compose rectangle defines the scaling ratio compared + to the size of the sink pad crop rectangle. The location of + the compose rectangle specifies the location of the actual + sink compose rectangle in the sink compose bounds + rectangle.</listitem> + + <listitem>Source pad actual crop selection. Crop on the source + pad defines crop performed to the image in the sink compose + bounds rectangle.</listitem> + + <listitem>Source pad format. The source pad format defines the + output pixel format of the subdev, as well as the other + parameters with the exception of the image width and height. + Width and height are defined by the size of the source pad + actual crop selection.</listitem> + </orderedlist> + + <para>Accessing any of the above rectangles not supported by the + subdev will return <constant>EINVAL</constant>. Any rectangle + referring to a previous unsupported rectangle coordinates will + instead refer to the previous supported rectangle. For example, + if sink crop is not supported, the compose selection will refer + to the sink pad format dimensions instead.</para> + + <figure id="subdev-image-processing-crop"> + <title>Image processing in subdevs: simple crop example</title> + <mediaobject> + <imageobject> + <imagedata fileref="subdev-image-processing-crop.svg" + format="SVG" scale="200" /> + </imageobject> + </mediaobject> + </figure> + + <para>In the above example, the subdev supports cropping on its + sink pad. To configure it, the user sets the media bus format on + the subdev's sink pad. Now the actual crop rectangle can be set + on the sink pad --- the location and size of this rectangle + reflect the location and size of a rectangle to be cropped from + the sink format. The size of the sink crop rectangle will also + be the size of the format of the subdev's source pad.</para> + + <figure id="subdev-image-processing-scaling-multi-source"> + <title>Image processing in subdevs: scaling with multiple sources</title> + <mediaobject> + <imageobject> + <imagedata fileref="subdev-image-processing-scaling-multi-source.svg" + format="SVG" scale="200" /> + </imageobject> + </mediaobject> + </figure> + + <para>In this example, the subdev is capable of first cropping, + then scaling and finally cropping for two source pads + individually from the resulting scaled image. The location of + the scaled image in the cropped image is ignored in sink compose + target. Both of the locations of the source crop rectangles + refer to the sink scaling rectangle, independently cropping an + area at location specified by the source crop rectangle from + it.</para> + + <figure id="subdev-image-processing-full"> + <title>Image processing in subdevs: scaling and composition + with multiple sinks and sources</title> + <mediaobject> + <imageobject> + <imagedata fileref="subdev-image-processing-full.svg" + format="SVG" scale="200" /> + </imageobject> + </mediaobject> + </figure> + + <para>The subdev driver supports two sink pads and two source + pads. The images from both of the sink pads are individually + cropped, then scaled and further composed on the composition + bounds rectangle. From that, two independent streams are cropped + and sent out of the subdev from the source pads.</para> </section> + </section> &sub-subdev-formats; diff --git a/Documentation/DocBook/media/v4l/io.xml b/Documentation/DocBook/media/v4l/io.xml index b815929b5bba..fd6aca2922b6 100644 --- a/Documentation/DocBook/media/v4l/io.xml +++ b/Documentation/DocBook/media/v4l/io.xml @@ -543,12 +543,13 @@ and can range from zero to the number of buffers allocated with the &VIDIOC-REQBUFS; ioctl (&v4l2-requestbuffers; <structfield>count</structfield>) minus one.</entry> </row> <row> - <entry>&v4l2-buf-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry></entry> <entry>Type of the buffer, same as &v4l2-format; <structfield>type</structfield> or &v4l2-requestbuffers; -<structfield>type</structfield>, set by the application.</entry> +<structfield>type</structfield>, set by the application. See <xref +linkend="v4l2-buf-type" /></entry> </row> <row> <entry>__u32</entry> @@ -568,7 +569,7 @@ refers to an input stream, applications when an output stream.</entry> linkend="buffer-flags" />.</entry> </row> <row> - <entry>&v4l2-field;</entry> + <entry>__u32</entry> <entry><structfield>field</structfield></entry> <entry></entry> <entry>Indicates the field order of the image in the @@ -630,11 +631,12 @@ bandwidth. These devices identify by not enumerating any video standards, see <xref linkend="standard" />.</para></entry> </row> <row> - <entry>&v4l2-memory;</entry> + <entry>__u32</entry> <entry><structfield>memory</structfield></entry> <entry></entry> <entry>This field must be set by applications and/or drivers -in accordance with the selected I/O method.</entry> +in accordance with the selected I/O method. See <xref linkend="v4l2-memory" + /></entry> </row> <row> <entry>union</entry> diff --git a/Documentation/DocBook/media/v4l/pixfmt-srggb10.xml b/Documentation/DocBook/media/v4l/pixfmt-srggb10.xml index 7b274092e60c..c1c62a9acc2a 100644 --- a/Documentation/DocBook/media/v4l/pixfmt-srggb10.xml +++ b/Documentation/DocBook/media/v4l/pixfmt-srggb10.xml @@ -1,4 +1,4 @@ - <refentry> + <refentry id="pixfmt-srggb10"> <refmeta> <refentrytitle>V4L2_PIX_FMT_SRGGB10 ('RG10'), V4L2_PIX_FMT_SGRBG10 ('BA10'), diff --git a/Documentation/DocBook/media/v4l/pixfmt-srggb10dpcm8.xml b/Documentation/DocBook/media/v4l/pixfmt-srggb10dpcm8.xml new file mode 100644 index 000000000000..8eace3e2e7d4 --- /dev/null +++ b/Documentation/DocBook/media/v4l/pixfmt-srggb10dpcm8.xml @@ -0,0 +1,29 @@ + <refentry id="pixfmt-srggb10dpcm8"> + <refmeta> + <refentrytitle> + V4L2_PIX_FMT_SBGGR10DPCM8 ('bBA8'), + V4L2_PIX_FMT_SGBRG10DPCM8 ('bGA8'), + V4L2_PIX_FMT_SGRBG10DPCM8 ('BD10'), + V4L2_PIX_FMT_SRGGB10DPCM8 ('bRA8'), + </refentrytitle> + &manvol; + </refmeta> + <refnamediv> + <refname id="V4L2-PIX-FMT-SBGGR10DPCM8"><constant>V4L2_PIX_FMT_SBGGR10DPCM8</constant></refname> + <refname id="V4L2-PIX-FMT-SGBRG10DPCM8"><constant>V4L2_PIX_FMT_SGBRG10DPCM8</constant></refname> + <refname id="V4L2-PIX-FMT-SGRBG10DPCM8"><constant>V4L2_PIX_FMT_SGRBG10DPCM8</constant></refname> + <refname id="V4L2-PIX-FMT-SRGGB10DPCM8"><constant>V4L2_PIX_FMT_SRGGB10DPCM8</constant></refname> + <refpurpose>10-bit Bayer formats compressed to 8 bits</refpurpose> + </refnamediv> + <refsect1> + <title>Description</title> + + <para>The following four pixel formats are raw sRGB / Bayer formats + with 10 bits per colour compressed to 8 bits each, using DPCM + compression. DPCM, differential pulse-code modulation, is lossy. + Each colour component consumes 8 bits of memory. In other respects + this format is similar to <xref + linkend="pixfmt-srggb10">.</xref></para> + + </refsect1> + </refentry> diff --git a/Documentation/DocBook/media/v4l/pixfmt.xml b/Documentation/DocBook/media/v4l/pixfmt.xml index 31eaae2469f9..f5ac15ed0549 100644 --- a/Documentation/DocBook/media/v4l/pixfmt.xml +++ b/Documentation/DocBook/media/v4l/pixfmt.xml @@ -673,6 +673,7 @@ access the palette, this must be done with ioctls of the Linux framebuffer API.< &sub-srggb8; &sub-sbggr16; &sub-srggb10; + &sub-srggb10dpcm8; &sub-srggb12; </section> @@ -876,11 +877,6 @@ kernel sources in the file <filename>Documentation/video4linux/cx2341x/README.hm <entry>'S561'</entry> <entry>Compressed GBRG Bayer format used by the gspca driver.</entry> </row> - <row id="V4L2-PIX-FMT-SGRBG10DPCM8"> - <entry><constant>V4L2_PIX_FMT_SGRBG10DPCM8</constant></entry> - <entry>'DB10'</entry> - <entry>10 bit raw Bayer DPCM compressed to 8 bits.</entry> - </row> <row id="V4L2-PIX-FMT-PAC207"> <entry><constant>V4L2_PIX_FMT_PAC207</constant></entry> <entry>'P207'</entry> diff --git a/Documentation/DocBook/media/v4l/subdev-image-processing-crop.dia b/Documentation/DocBook/media/v4l/subdev-image-processing-crop.dia new file mode 100644 index 000000000000..e32ba5362e1d --- /dev/null +++ b/Documentation/DocBook/media/v4l/subdev-image-processing-crop.dia @@ -0,0 +1,614 @@ +<?xml version="1.0" encoding="UTF-8"?> +<dia:diagram xmlns:dia="http://www.lysator.liu.se/~alla/dia/"> + <dia:diagramdata> + <dia:attribute name="background"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="pagebreak"> + <dia:color val="#000099"/> + </dia:attribute> + <dia:attribute name="paper"> + <dia:composite type="paper"> + <dia:attribute name="name"> + <dia:string>#A4#</dia:string> + </dia:attribute> + <dia:attribute name="tmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="bmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="lmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="rmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="is_portrait"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="scaling"> + <dia:real val="0.49000000953674316"/> + </dia:attribute> + <dia:attribute name="fitto"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="grid"> + <dia:composite type="grid"> + <dia:attribute name="width_x"> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="width_y"> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="visible_x"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="visible_y"> + <dia:int val="1"/> + </dia:attribute> + <dia:composite type="color"/> + </dia:composite> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#d8e5e5"/> + </dia:attribute> + <dia:attribute name="guides"> + <dia:composite type="guides"> + <dia:attribute name="hguides"/> + <dia:attribute name="vguides"/> + </dia:composite> + </dia:attribute> + </dia:diagramdata> + <dia:layer name="Background" visible="true" active="true"> + <dia:object type="Standard - Box" version="0" id="O0"> + <dia:attribute name="obj_pos"> + <dia:point val="-0.4,6.5"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-0.45,6.45;23.1387,16.2"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="-0.4,6.5"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="23.48871579904775"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="9.6500000000000004"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O1"> + <dia:attribute name="obj_pos"> + <dia:point val="0.225,9.45"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="0.175,9.4;8.225,14.7"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="0.225,9.45"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="7.9499999999999975"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="5.1999999999999975"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#a52a2a"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O2"> + <dia:attribute name="obj_pos"> + <dia:point val="3.175,10.55"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="3.125,10.5;7.925,14.45"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="3.175,10.55"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="4.6999999999999975"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.8499999999999979"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O3"> + <dia:attribute name="obj_pos"> + <dia:point val="3.725,11.3875"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="3.725,10.7925;6.6025,13.14"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink +crop +selection#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="3.725,11.3875"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O4"> + <dia:attribute name="obj_pos"> + <dia:point val="1.475,7.9"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="1.475,7.305;1.475,8.0525"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>##</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="1.475,7.9"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O5"> + <dia:attribute name="obj_pos"> + <dia:point val="0.426918,7.89569"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="0.426918,7.30069;3.90942,8.84819"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink media +bus format#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="0.426918,7.89569"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#a52a2a"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O6"> + <dia:attribute name="obj_pos"> + <dia:point val="17.4887,7.75"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="17.4887,7.155;21.8112,8.7025"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#source media +bus format#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="17.4887,7.75"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#8b6914"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O7"> + <dia:attribute name="obj_pos"> + <dia:point val="17.5244,9.5417"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="17.4744,9.4917;22.2387,13.35"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="17.5244,9.5417"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="4.6643157990477508"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.758300000000002"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#8b6914"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O8"> + <dia:attribute name="obj_pos"> + <dia:point val="17.5244,13.3"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="3.12132,13.2463;17.5781,14.4537"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="17.5244,13.3"/> + <dia:point val="3.175,14.4"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O7" connection="5"/> + <dia:connection handle="1" to="O2" connection="5"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O9"> + <dia:attribute name="obj_pos"> + <dia:point val="17.5244,9.5417"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="3.12162,9.48832;17.5778,10.6034"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="17.5244,9.5417"/> + <dia:point val="3.175,10.55"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O7" connection="0"/> + <dia:connection handle="1" to="O2" connection="0"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O10"> + <dia:attribute name="obj_pos"> + <dia:point val="22.1887,13.3"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="7.82132,13.2463;22.2424,14.4537"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="22.1887,13.3"/> + <dia:point val="7.875,14.4"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O7" connection="7"/> + <dia:connection handle="1" to="O2" connection="7"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O11"> + <dia:attribute name="obj_pos"> + <dia:point val="22.1887,9.5417"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="7.82161,9.48831;22.2421,10.6034"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="22.1887,9.5417"/> + <dia:point val="7.875,10.55"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O7" connection="2"/> + <dia:connection handle="1" to="O2" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O12"> + <dia:attribute name="obj_pos"> + <dia:point val="23.23,10.5742"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="23.18,10.5242;24.13,11.4742"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="23.23,10.5742"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O13"> + <dia:attribute name="obj_pos"> + <dia:point val="24.08,10.9992"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="24.03,10.6388;32.4953,11.3624"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="24.08,10.9992"/> + <dia:point val="32.3835,11.0007"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O12" connection="3"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O14"> + <dia:attribute name="obj_pos"> + <dia:point val="25.3454,10.49"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="25.3454,9.895;29.9904,10.6425"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 1 (source)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="25.3454,10.49"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O15"> + <dia:attribute name="obj_pos"> + <dia:point val="-1.44491,11.6506"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-1.49491,11.6006;-0.54491,12.5506"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="-1.44491,11.6506"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O16"> + <dia:attribute name="obj_pos"> + <dia:point val="-9.61991,12.09"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-9.67,11.7149;-1.33311,12.4385"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="-9.61991,12.09"/> + <dia:point val="-1.44491,12.0756"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O15" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O17"> + <dia:attribute name="obj_pos"> + <dia:point val="-7.39291,11.49"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-7.39291,10.895;-3.58791,11.6425"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 0 (sink)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="-7.39291,11.49"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + </dia:layer> +</dia:diagram> diff --git a/Documentation/DocBook/media/v4l/subdev-image-processing-crop.svg b/Documentation/DocBook/media/v4l/subdev-image-processing-crop.svg new file mode 100644 index 000000000000..18b0f5de9ed2 --- /dev/null +++ b/Documentation/DocBook/media/v4l/subdev-image-processing-crop.svg @@ -0,0 +1,63 @@ +<?xml version="1.0" encoding="UTF-8" standalone="no"?> +<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.0//EN" "http://www.w3.org/TR/2001/PR-SVG-20010719/DTD/svg10.dtd"> +<svg width="43cm" height="10cm" viewBox="-194 128 844 196" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink"> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="-8" y="130" width="469.774" height="193"/> + <g> + <rect style="fill: #ffffff" x="4.5" y="189" width="159" height="104"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a52a2a" x="4.5" y="189" width="159" height="104"/> + </g> + <g> + <rect style="fill: #ffffff" x="63.5" y="211" width="94" height="77"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #0000ff" x="63.5" y="211" width="94" height="77"/> + </g> + <text style="fill: #0000ff;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="74.5" y="227.75"> + <tspan x="74.5" y="227.75">sink</tspan> + <tspan x="74.5" y="243.75">crop</tspan> + <tspan x="74.5" y="259.75">selection</tspan> + </text> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="29.5" y="158"> + <tspan x="29.5" y="158"></tspan> + </text> + <text style="fill: #a52a2a;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="8.53836" y="157.914"> + <tspan x="8.53836" y="157.914">sink media</tspan> + <tspan x="8.53836" y="173.914">bus format</tspan> + </text> + <text style="fill: #8b6914;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="349.774" y="155"> + <tspan x="349.774" y="155">source media</tspan> + <tspan x="349.774" y="171">bus format</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="350.488" y="190.834" width="93.2863" height="75.166"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #8b6914" x="350.488" y="190.834" width="93.2863" height="75.166"/> + </g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="350.488" y1="266" x2="63.5" y2="288"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="350.488" y1="190.834" x2="63.5" y2="211"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="443.774" y1="266" x2="157.5" y2="288"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="443.774" y1="190.834" x2="157.5" y2="211"/> + <g> + <ellipse style="fill: #ffffff" cx="473.1" cy="219.984" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="473.1" cy="219.984" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="473.1" cy="219.984" rx="8.5" ry="8.5"/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="481.6" y1="219.984" x2="637.934" y2="220.012"/> + <polygon style="fill: #000000" points="645.434,220.014 635.433,225.012 637.934,220.012 635.435,215.012 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="645.434,220.014 635.433,225.012 637.934,220.012 635.435,215.012 "/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="506.908" y="209.8"> + <tspan x="506.908" y="209.8">pad 1 (source)</tspan> + </text> + <g> + <ellipse style="fill: #ffffff" cx="-20.3982" cy="241.512" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="-20.3982" cy="241.512" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="-20.3982" cy="241.512" rx="8.5" ry="8.5"/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="-192.398" y1="241.8" x2="-38.6343" y2="241.529"/> + <polygon style="fill: #000000" points="-31.1343,241.516 -41.1254,246.534 -38.6343,241.529 -41.1431,236.534 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="-31.1343,241.516 -41.1254,246.534 -38.6343,241.529 -41.1431,236.534 "/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="-147.858" y="229.8"> + <tspan x="-147.858" y="229.8">pad 0 (sink)</tspan> + </text> +</svg> diff --git a/Documentation/DocBook/media/v4l/subdev-image-processing-full.dia b/Documentation/DocBook/media/v4l/subdev-image-processing-full.dia new file mode 100644 index 000000000000..a0d782927840 --- /dev/null +++ b/Documentation/DocBook/media/v4l/subdev-image-processing-full.dia @@ -0,0 +1,1588 @@ +<?xml version="1.0" encoding="UTF-8"?> +<dia:diagram xmlns:dia="http://www.lysator.liu.se/~alla/dia/"> + <dia:diagramdata> + <dia:attribute name="background"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="pagebreak"> + <dia:color val="#000099"/> + </dia:attribute> + <dia:attribute name="paper"> + <dia:composite type="paper"> + <dia:attribute name="name"> + <dia:string>#A4#</dia:string> + </dia:attribute> + <dia:attribute name="tmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="bmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="lmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="rmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="is_portrait"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="scaling"> + <dia:real val="0.49000000953674316"/> + </dia:attribute> + <dia:attribute name="fitto"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="grid"> + <dia:composite type="grid"> + <dia:attribute name="width_x"> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="width_y"> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="visible_x"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="visible_y"> + <dia:int val="1"/> + </dia:attribute> + <dia:composite type="color"/> + </dia:composite> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#d8e5e5"/> + </dia:attribute> + <dia:attribute name="guides"> + <dia:composite type="guides"> + <dia:attribute name="hguides"/> + <dia:attribute name="vguides"/> + </dia:composite> + </dia:attribute> + </dia:diagramdata> + <dia:layer name="Background" visible="true" active="true"> + <dia:object type="Standard - Box" version="0" id="O0"> + <dia:attribute name="obj_pos"> + <dia:point val="15.945,6.45"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="15.895,6.4;26.4,18.95"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="15.945,6.45"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="10.404999999254942"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="12.449999999999992"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#ff765a"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O1"> + <dia:attribute name="obj_pos"> + <dia:point val="-0.1,3.65"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-0.15,3.6;40.25,20.85"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="-0.1,3.65"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="40.300000000000004"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="17.149999999999999"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O2"> + <dia:attribute name="obj_pos"> + <dia:point val="-1.05,7.9106"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-1.1,7.8606;-0.15,8.8106"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="-1.05,7.9106"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O3"> + <dia:attribute name="obj_pos"> + <dia:point val="40.3366,9.8342"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="40.2866,9.7842;41.2366,10.7342"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="40.3366,9.8342"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O4"> + <dia:attribute name="obj_pos"> + <dia:point val="-9.225,8.35"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-9.27509,7.97487;-0.938197,8.69848"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="-9.225,8.35"/> + <dia:point val="-1.05,8.3356"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O2" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O5"> + <dia:attribute name="obj_pos"> + <dia:point val="41.1866,10.2592"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="41.1366,9.89879;49.6019,10.6224"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="41.1866,10.2592"/> + <dia:point val="49.4901,10.2607"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O3" connection="3"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O6"> + <dia:attribute name="obj_pos"> + <dia:point val="-6.998,7.75"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-6.998,7.155;-3.193,7.9025"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 0 (sink)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="-6.998,7.75"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O7"> + <dia:attribute name="obj_pos"> + <dia:point val="42.452,9.75"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="42.452,9.155;47.097,9.9025"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 2 (source)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="42.452,9.75"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O8"> + <dia:attribute name="obj_pos"> + <dia:point val="0.275,6"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="0.225,5.95;8.275,11.25"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="0.275,6"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="7.9499999999999975"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="5.1999999999999975"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#a52a2a"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O9"> + <dia:attribute name="obj_pos"> + <dia:point val="3.125,6.8"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="3.075,6.75;7.875,10.7"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="3.125,6.8"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="4.6999999999999975"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.8499999999999979"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O10"> + <dia:attribute name="obj_pos"> + <dia:point val="1.525,4.45"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="1.525,3.855;1.525,4.6025"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>##</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="1.525,4.45"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O11"> + <dia:attribute name="obj_pos"> + <dia:point val="0.476918,4.44569"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="0.476918,3.85069;3.95942,5.39819"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink media +bus format#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="0.476918,4.44569"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#a52a2a"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O12"> + <dia:attribute name="obj_pos"> + <dia:point val="16.6822,9.28251"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="16.6322,9.23251;24.9922,17.9564"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="16.6822,9.28251"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="8.2600228398861297"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="8.6238900617957164"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#00ff00"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O13"> + <dia:attribute name="obj_pos"> + <dia:point val="16.6822,17.9064"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="3.05732,10.5823;16.7499,17.9741"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="16.6822,17.9064"/> + <dia:point val="3.125,10.65"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O12" connection="5"/> + <dia:connection handle="1" to="O9" connection="5"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O14"> + <dia:attribute name="obj_pos"> + <dia:point val="16.6822,9.28251"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="3.06681,6.74181;16.7404,9.3407"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="16.6822,9.28251"/> + <dia:point val="3.125,6.8"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O12" connection="0"/> + <dia:connection handle="1" to="O9" connection="0"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O15"> + <dia:attribute name="obj_pos"> + <dia:point val="24.9422,17.9064"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="7.75945,10.5845;25.0077,17.9719"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="24.9422,17.9064"/> + <dia:point val="7.825,10.65"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O12" connection="7"/> + <dia:connection handle="1" to="O9" connection="7"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O16"> + <dia:attribute name="obj_pos"> + <dia:point val="24.9422,9.28251"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="7.76834,6.74334;24.9989,9.33917"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="24.9422,9.28251"/> + <dia:point val="7.825,6.8"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O12" connection="2"/> + <dia:connection handle="1" to="O9" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O17"> + <dia:attribute name="obj_pos"> + <dia:point val="16.7352,7.47209"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="16.7352,6.87709;22.5602,8.42459"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink compose +selection (scaling)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="16.7352,7.47209"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#00ff00"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O18"> + <dia:attribute name="obj_pos"> + <dia:point val="20.4661,9.72825"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="20.4161,9.67825;25.5254,13.3509"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="20.4661,9.72825"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="5.009308462554376"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.5726155970598077"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O19"> + <dia:attribute name="obj_pos"> + <dia:point val="34.475,5.2564"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="34.475,4.6614;38.7975,6.2089"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#source media +bus format#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="34.475,5.2564"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#8b6914"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O20"> + <dia:attribute name="obj_pos"> + <dia:point val="34.4244,8.6917"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="34.3744,8.6417;39.4837,12.3143"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="34.4244,8.6917"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="5.009308462554376"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.5726155970598077"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#8b6914"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O21"> + <dia:attribute name="obj_pos"> + <dia:point val="34.4244,12.2643"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="20.4125,12.2107;34.478,13.3545"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="34.4244,12.2643"/> + <dia:point val="20.4661,13.3009"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O20" connection="5"/> + <dia:connection handle="1" to="O18" connection="5"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O22"> + <dia:attribute name="obj_pos"> + <dia:point val="34.4244,8.6917"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="20.4125,8.63813;34.478,9.78182"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="34.4244,8.6917"/> + <dia:point val="20.4661,9.72825"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O20" connection="0"/> + <dia:connection handle="1" to="O18" connection="0"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O23"> + <dia:attribute name="obj_pos"> + <dia:point val="39.4337,12.2643"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="25.4218,12.2107;39.4873,13.3545"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="39.4337,12.2643"/> + <dia:point val="25.4754,13.3009"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O20" connection="7"/> + <dia:connection handle="1" to="O18" connection="7"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O24"> + <dia:attribute name="obj_pos"> + <dia:point val="39.4337,8.6917"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="25.4218,8.63813;39.4873,9.78182"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="39.4337,8.6917"/> + <dia:point val="25.4754,9.72825"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O20" connection="2"/> + <dia:connection handle="1" to="O18" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O25"> + <dia:attribute name="obj_pos"> + <dia:point val="16.25,5.15"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="16.25,4.555;21.68,6.1025"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink compose +bounds selection#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="16.25,5.15"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#ff765a"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O26"> + <dia:attribute name="obj_pos"> + <dia:point val="-1.02991,16.6506"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-1.07991,16.6006;-0.12991,17.5506"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="-1.02991,16.6506"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O27"> + <dia:attribute name="obj_pos"> + <dia:point val="-9.20491,17.09"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-9.255,16.7149;-0.918107,17.4385"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="-9.20491,17.09"/> + <dia:point val="-1.02991,17.0756"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O26" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O28"> + <dia:attribute name="obj_pos"> + <dia:point val="-6.95,16.45"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-6.95,15.855;-3.145,16.6025"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 1 (sink)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="-6.95,16.45"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O29"> + <dia:attribute name="obj_pos"> + <dia:point val="0.390412,14.64"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="0.340412,14.59;6.045,18.8"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="0.390412,14.64"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="5.604587512785236"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="4.1099999999999994"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#a52a2a"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O30"> + <dia:attribute name="obj_pos"> + <dia:point val="2.645,15.74"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="2.595,15.69;5.6,18.3"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="2.645,15.74"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="2.904999999254942"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="2.5100000000000016"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O31"> + <dia:attribute name="obj_pos"> + <dia:point val="1.595,12.99"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="1.595,12.395;1.595,13.1425"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>##</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="1.595,12.99"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O32"> + <dia:attribute name="obj_pos"> + <dia:point val="17.945,12.595"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="2.58596,12.536;18.004,15.799"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="17.945,12.595"/> + <dia:point val="2.645,15.74"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O36" connection="0"/> + <dia:connection handle="1" to="O30" connection="0"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O33"> + <dia:attribute name="obj_pos"> + <dia:point val="17.945,15.8"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="2.58772,15.7427;18.0023,18.3073"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="17.945,15.8"/> + <dia:point val="2.645,18.25"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O36" connection="5"/> + <dia:connection handle="1" to="O30" connection="5"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O34"> + <dia:attribute name="obj_pos"> + <dia:point val="21.7,15.8"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="5.49307,15.7431;21.7569,18.3069"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="21.7,15.8"/> + <dia:point val="5.55,18.25"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O36" connection="7"/> + <dia:connection handle="1" to="O30" connection="7"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O35"> + <dia:attribute name="obj_pos"> + <dia:point val="21.7,12.595"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="5.49136,12.5364;21.7586,15.7986"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="21.7,12.595"/> + <dia:point val="5.55,15.74"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O36" connection="2"/> + <dia:connection handle="1" to="O30" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O36"> + <dia:attribute name="obj_pos"> + <dia:point val="17.945,12.595"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="17.895,12.545;21.75,15.85"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="17.945,12.595"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="3.7549999992549452"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.2049999992549427"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#00ff00"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O37"> + <dia:attribute name="obj_pos"> + <dia:point val="22.1631,14.2233"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="22.1131,14.1733;25.45,16.7"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="22.1631,14.2233"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="3.2369000000000021"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="2.4267000000000003"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O38"> + <dia:attribute name="obj_pos"> + <dia:point val="34.6714,16.2367"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="34.6214,16.1867;37.9,18.75"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="34.6714,16.2367"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="3.178600000000003"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="2.4632999999999967"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#8b6914"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O39"> + <dia:attribute name="obj_pos"> + <dia:point val="34.6714,18.7"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="22.1057,16.5926;34.7288,18.7574"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="34.6714,18.7"/> + <dia:point val="22.1631,16.65"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O38" connection="5"/> + <dia:connection handle="1" to="O37" connection="5"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O40"> + <dia:attribute name="obj_pos"> + <dia:point val="34.6714,16.2367"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="22.1058,14.166;34.7287,16.294"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="34.6714,16.2367"/> + <dia:point val="22.1631,14.2233"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O38" connection="0"/> + <dia:connection handle="1" to="O37" connection="0"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O41"> + <dia:attribute name="obj_pos"> + <dia:point val="37.85,18.7"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="25.3425,16.5925;37.9075,18.7575"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="37.85,18.7"/> + <dia:point val="25.4,16.65"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O38" connection="7"/> + <dia:connection handle="1" to="O37" connection="7"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O42"> + <dia:attribute name="obj_pos"> + <dia:point val="37.85,16.2367"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="25.3427,14.166;37.9073,16.294"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="37.85,16.2367"/> + <dia:point val="25.4,14.2233"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O38" connection="2"/> + <dia:connection handle="1" to="O37" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O43"> + <dia:attribute name="obj_pos"> + <dia:point val="40.347,16.7742"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="40.297,16.7242;41.247,17.6742"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="40.347,16.7742"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O44"> + <dia:attribute name="obj_pos"> + <dia:point val="41.197,17.1992"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="41.147,16.8388;49.6123,17.5624"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="41.197,17.1992"/> + <dia:point val="49.5005,17.2007"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O43" connection="3"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O45"> + <dia:attribute name="obj_pos"> + <dia:point val="42.4624,16.69"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="42.4624,16.095;47.1074,16.8425"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 3 (source)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="42.4624,16.69"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O46"> + <dia:attribute name="obj_pos"> + <dia:point val="9.85,4.55"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="9.85,3.955;12.7275,6.3025"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink +crop +selection#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="9.85,4.55"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O47"> + <dia:attribute name="obj_pos"> + <dia:point val="27.65,4.75"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="27.65,4.155;30.5275,6.5025"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#source +crop +selection#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="27.65,4.75"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O48"> + <dia:attribute name="obj_pos"> + <dia:point val="10.55,6.6"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="7.7135,6.39438;10.6035,7.11605"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="10.55,6.6"/> + <dia:point val="7.825,6.8"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O9" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O49"> + <dia:attribute name="obj_pos"> + <dia:point val="10.45,6.55"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="5.48029,6.48236;10.5176,15.8387"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="10.45,6.55"/> + <dia:point val="5.55,15.74"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O30" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O50"> + <dia:attribute name="obj_pos"> + <dia:point val="27.5246,6.66071"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="25.406,6.59136;27.594,9.82122"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="27.5246,6.66071"/> + <dia:point val="25.4754,9.72825"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O18" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O51"> + <dia:attribute name="obj_pos"> + <dia:point val="27.5036,6.68935"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="25.2161,6.62775;27.5652,14.331"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="27.5036,6.68935"/> + <dia:point val="25.4,14.2233"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O37" connection="2"/> + </dia:connections> + </dia:object> + </dia:layer> +</dia:diagram> diff --git a/Documentation/DocBook/media/v4l/subdev-image-processing-full.svg b/Documentation/DocBook/media/v4l/subdev-image-processing-full.svg new file mode 100644 index 000000000000..3322cf4c0093 --- /dev/null +++ b/Documentation/DocBook/media/v4l/subdev-image-processing-full.svg @@ -0,0 +1,163 @@ +<?xml version="1.0" encoding="UTF-8" standalone="no"?> +<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.0//EN" "http://www.w3.org/TR/2001/PR-SVG-20010719/DTD/svg10.dtd"> +<svg width="59cm" height="18cm" viewBox="-186 71 1178 346" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink"> + <g> + <rect style="fill: #ffffff" x="318.9" y="129" width="208.1" height="249"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #ff765a" x="318.9" y="129" width="208.1" height="249"/> + </g> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="-2" y="73" width="806" height="343"/> + <g> + <ellipse style="fill: #ffffff" cx="-12.5" cy="166.712" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="-12.5" cy="166.712" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="-12.5" cy="166.712" rx="8.5" ry="8.5"/> + </g> + <g> + <ellipse style="fill: #ffffff" cx="815.232" cy="205.184" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="815.232" cy="205.184" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="815.232" cy="205.184" rx="8.5" ry="8.5"/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="-184.5" y1="167" x2="-30.7361" y2="166.729"/> + <polygon style="fill: #000000" points="-23.2361,166.716 -33.2272,171.734 -30.7361,166.729 -33.2449,161.734 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="-23.2361,166.716 -33.2272,171.734 -30.7361,166.729 -33.2449,161.734 "/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="823.732" y1="205.184" x2="980.066" y2="205.212"/> + <polygon style="fill: #000000" points="987.566,205.214 977.565,210.212 980.066,205.212 977.567,200.212 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="987.566,205.214 977.565,210.212 980.066,205.212 977.567,200.212 "/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="-139.96" y="155"> + <tspan x="-139.96" y="155">pad 0 (sink)</tspan> + </text> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="849.04" y="195"> + <tspan x="849.04" y="195">pad 2 (source)</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="5.5" y="120" width="159" height="104"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a52a2a" x="5.5" y="120" width="159" height="104"/> + </g> + <g> + <rect style="fill: #ffffff" x="62.5" y="136" width="94" height="77"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #0000ff" x="62.5" y="136" width="94" height="77"/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="30.5" y="89"> + <tspan x="30.5" y="89"></tspan> + </text> + <text style="fill: #a52a2a;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="9.53836" y="88.9138"> + <tspan x="9.53836" y="88.9138">sink media</tspan> + <tspan x="9.53836" y="104.914">bus format</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="333.644" y="185.65" width="165.2" height="172.478"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #00ff00" x="333.644" y="185.65" width="165.2" height="172.478"/> + </g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="333.644" y1="358.128" x2="62.5" y2="213"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="333.644" y1="185.65" x2="62.5" y2="136"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="498.844" y1="358.128" x2="156.5" y2="213"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="498.844" y1="185.65" x2="156.5" y2="136"/> + <text style="fill: #00ff00;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="334.704" y="149.442"> + <tspan x="334.704" y="149.442">sink compose</tspan> + <tspan x="334.704" y="165.442">selection (scaling)</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="409.322" y="194.565" width="100.186" height="71.4523"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" x="409.322" y="194.565" width="100.186" height="71.4523"/> + </g> + <text style="fill: #8b6914;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="689.5" y="105.128"> + <tspan x="689.5" y="105.128">source media</tspan> + <tspan x="689.5" y="121.128">bus format</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="688.488" y="173.834" width="100.186" height="71.4523"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #8b6914" x="688.488" y="173.834" width="100.186" height="71.4523"/> + </g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="688.488" y1="245.286" x2="409.322" y2="266.018"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="688.488" y1="173.834" x2="409.322" y2="194.565"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="788.674" y1="245.286" x2="509.508" y2="266.018"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="788.674" y1="173.834" x2="509.508" y2="194.565"/> + <text style="fill: #ff765a;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="325" y="103"> + <tspan x="325" y="103">sink compose</tspan> + <tspan x="325" y="119">bounds selection</tspan> + </text> + <g> + <ellipse style="fill: #ffffff" cx="-12.0982" cy="341.512" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="-12.0982" cy="341.512" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="-12.0982" cy="341.512" rx="8.5" ry="8.5"/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="-184.098" y1="341.8" x2="-30.3343" y2="341.529"/> + <polygon style="fill: #000000" points="-22.8343,341.516 -32.8254,346.534 -30.3343,341.529 -32.8431,336.534 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="-22.8343,341.516 -32.8254,346.534 -30.3343,341.529 -32.8431,336.534 "/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="-139" y="329"> + <tspan x="-139" y="329">pad 1 (sink)</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="7.80824" y="292.8" width="112.092" height="82.2"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a52a2a" x="7.80824" y="292.8" width="112.092" height="82.2"/> + </g> + <g> + <rect style="fill: #ffffff" x="52.9" y="314.8" width="58.1" height="50.2"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #0000ff" x="52.9" y="314.8" width="58.1" height="50.2"/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="31.9" y="259.8"> + <tspan x="31.9" y="259.8"></tspan> + </text> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="358.9" y1="251.9" x2="52.9" y2="314.8"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="358.9" y1="316" x2="52.9" y2="365"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="434" y1="316" x2="111" y2="365"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="434" y1="251.9" x2="111" y2="314.8"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #00ff00" x="358.9" y="251.9" width="75.1" height="64.1"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" x="443.262" y="284.466" width="64.738" height="48.534"/> + <g> + <rect style="fill: #ffffff" x="693.428" y="324.734" width="63.572" height="49.266"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #8b6914" x="693.428" y="324.734" width="63.572" height="49.266"/> + </g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="693.428" y1="374" x2="443.262" y2="333"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="693.428" y1="324.734" x2="443.262" y2="284.466"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="757" y1="374" x2="508" y2="333"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="757" y1="324.734" x2="508" y2="284.466"/> + <g> + <ellipse style="fill: #ffffff" cx="815.44" cy="343.984" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="815.44" cy="343.984" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="815.44" cy="343.984" rx="8.5" ry="8.5"/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="823.94" y1="343.984" x2="980.274" y2="344.012"/> + <polygon style="fill: #000000" points="987.774,344.014 977.773,349.012 980.274,344.012 977.775,339.012 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="987.774,344.014 977.773,349.012 980.274,344.012 977.775,339.012 "/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="849.248" y="333.8"> + <tspan x="849.248" y="333.8">pad 3 (source)</tspan> + </text> + <text style="fill: #0000ff;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="197" y="91"> + <tspan x="197" y="91">sink</tspan> + <tspan x="197" y="107">crop</tspan> + <tspan x="197" y="123">selection</tspan> + </text> + <text style="fill: #a020f0;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="553" y="95"> + <tspan x="553" y="95">source</tspan> + <tspan x="553" y="111">crop</tspan> + <tspan x="553" y="127">selection</tspan> + </text> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #0000ff" x1="211" y1="132" x2="166.21" y2="135.287"/> + <polygon style="fill: #0000ff" points="158.73,135.836 168.337,130.118 166.21,135.287 169.069,140.091 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #0000ff" points="158.73,135.836 168.337,130.118 166.21,135.287 169.069,140.091 "/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #0000ff" x1="209" y1="131" x2="115.581" y2="306.209"/> + <polygon style="fill: #0000ff" points="112.052,312.827 112.345,301.65 115.581,306.209 121.169,306.355 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #0000ff" points="112.052,312.827 112.345,301.65 115.581,306.209 121.169,306.355 "/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" x1="550.492" y1="133.214" x2="514.916" y2="186.469"/> + <polygon style="fill: #a020f0" points="510.75,192.706 512.147,181.613 514.916,186.469 520.463,187.168 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" points="510.75,192.706 512.147,181.613 514.916,186.469 520.463,187.168 "/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" x1="550.072" y1="133.787" x2="510.618" y2="275.089"/> + <polygon style="fill: #a020f0" points="508.601,282.312 506.475,271.336 510.618,275.089 516.106,274.025 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" points="508.601,282.312 506.475,271.336 510.618,275.089 516.106,274.025 "/> + </g> +</svg> diff --git a/Documentation/DocBook/media/v4l/subdev-image-processing-scaling-multi-source.dia b/Documentation/DocBook/media/v4l/subdev-image-processing-scaling-multi-source.dia new file mode 100644 index 000000000000..0cd50a7bda80 --- /dev/null +++ b/Documentation/DocBook/media/v4l/subdev-image-processing-scaling-multi-source.dia @@ -0,0 +1,1152 @@ +<?xml version="1.0" encoding="UTF-8"?> +<dia:diagram xmlns:dia="http://www.lysator.liu.se/~alla/dia/"> + <dia:diagramdata> + <dia:attribute name="background"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="pagebreak"> + <dia:color val="#000099"/> + </dia:attribute> + <dia:attribute name="paper"> + <dia:composite type="paper"> + <dia:attribute name="name"> + <dia:string>#A4#</dia:string> + </dia:attribute> + <dia:attribute name="tmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="bmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="lmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="rmargin"> + <dia:real val="2.8222000598907471"/> + </dia:attribute> + <dia:attribute name="is_portrait"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="scaling"> + <dia:real val="0.49000000953674316"/> + </dia:attribute> + <dia:attribute name="fitto"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="grid"> + <dia:composite type="grid"> + <dia:attribute name="width_x"> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="width_y"> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="visible_x"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="visible_y"> + <dia:int val="1"/> + </dia:attribute> + <dia:composite type="color"/> + </dia:composite> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#d8e5e5"/> + </dia:attribute> + <dia:attribute name="guides"> + <dia:composite type="guides"> + <dia:attribute name="hguides"/> + <dia:attribute name="vguides"/> + </dia:composite> + </dia:attribute> + </dia:diagramdata> + <dia:layer name="Background" visible="true" active="true"> + <dia:object type="Standard - Box" version="0" id="O0"> + <dia:attribute name="obj_pos"> + <dia:point val="-0.4,6.5"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-0.45,6.45;39.95,22.9"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="-0.4,6.5"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="40.299999999999997"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="16.349999999999998"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O1"> + <dia:attribute name="obj_pos"> + <dia:point val="0.225,9.45"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="0.175,9.4;8.225,14.7"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="0.225,9.45"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="7.9499999999999975"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="5.1999999999999975"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#a52a2a"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O2"> + <dia:attribute name="obj_pos"> + <dia:point val="2.475,10.2"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="2.425,10.15;7.225,14.1"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="2.475,10.2"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="4.6999999999999975"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.8499999999999979"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O3"> + <dia:attribute name="obj_pos"> + <dia:point val="3,11.2"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="3,10.605;5.8775,12.9525"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink +crop +selection#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="3,11.2"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#0000ff"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O4"> + <dia:attribute name="obj_pos"> + <dia:point val="1.475,7.9"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="1.475,7.305;1.475,8.0525"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>##</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="1.475,7.9"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O5"> + <dia:attribute name="obj_pos"> + <dia:point val="0.426918,7.89569"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="0.426918,7.30069;3.90942,8.84819"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink media +bus format#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="0.426918,7.89569"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#a52a2a"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O6"> + <dia:attribute name="obj_pos"> + <dia:point val="16.6822,9.28251"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="16.6322,9.23251;24.9922,17.9564"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="16.6822,9.28251"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="8.2600228398861297"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="8.6238900617957164"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#00ff00"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O7"> + <dia:attribute name="obj_pos"> + <dia:point val="16.6822,17.9064"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="2.41365,13.9886;16.7436,17.9678"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="16.6822,17.9064"/> + <dia:point val="2.475,14.05"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O6" connection="5"/> + <dia:connection handle="1" to="O2" connection="5"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O8"> + <dia:attribute name="obj_pos"> + <dia:point val="16.6822,9.28251"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="2.42188,9.22939;16.7353,10.2531"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="16.6822,9.28251"/> + <dia:point val="2.475,10.2"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O6" connection="0"/> + <dia:connection handle="1" to="O2" connection="0"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O9"> + <dia:attribute name="obj_pos"> + <dia:point val="24.9422,17.9064"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="7.11553,13.9905;25.0017,17.9659"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="24.9422,17.9064"/> + <dia:point val="7.175,14.05"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O6" connection="7"/> + <dia:connection handle="1" to="O2" connection="7"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O10"> + <dia:attribute name="obj_pos"> + <dia:point val="24.9422,9.28251"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="7.12249,9.23;24.9947,10.2525"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="24.9422,9.28251"/> + <dia:point val="7.175,10.2"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O6" connection="2"/> + <dia:connection handle="1" to="O2" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O11"> + <dia:attribute name="obj_pos"> + <dia:point val="16.7352,7.47209"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="16.7352,6.87709;22.5602,8.42459"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#sink compose +selection (scaling)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="16.7352,7.47209"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#00ff00"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O12"> + <dia:attribute name="obj_pos"> + <dia:point val="19.1161,9.97825"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="19.0661,9.92825;24.1754,13.6009"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="19.1161,9.97825"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="5.009308462554376"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.5726155970598077"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O13"> + <dia:attribute name="obj_pos"> + <dia:point val="27.1661,7.47209"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="27.1661,6.87709;30.0436,9.22459"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#source +crop +selection#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="27.1661,7.47209"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O14"> + <dia:attribute name="obj_pos"> + <dia:point val="34.575,7.8564"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="34.575,7.2614;38.8975,8.8089"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#source media +bus format#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="34.575,7.8564"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#8b6914"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O15"> + <dia:attribute name="obj_pos"> + <dia:point val="34.5244,11.2917"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="34.4744,11.2417;39.5837,14.9143"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="34.5244,11.2917"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="5.009308462554376"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.5726155970598077"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#8b6914"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O16"> + <dia:attribute name="obj_pos"> + <dia:point val="34.5244,14.8643"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="19.062,13.4968;34.5785,14.9184"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="34.5244,14.8643"/> + <dia:point val="19.1161,13.5509"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O15" connection="5"/> + <dia:connection handle="1" to="O12" connection="5"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O17"> + <dia:attribute name="obj_pos"> + <dia:point val="34.5244,11.2917"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="19.062,9.92418;34.5785,11.3458"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="34.5244,11.2917"/> + <dia:point val="19.1161,9.97825"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O15" connection="0"/> + <dia:connection handle="1" to="O12" connection="0"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O18"> + <dia:attribute name="obj_pos"> + <dia:point val="39.5337,14.8643"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="24.0713,13.4968;39.5878,14.9184"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="39.5337,14.8643"/> + <dia:point val="24.1254,13.5509"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O15" connection="7"/> + <dia:connection handle="1" to="O12" connection="7"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O19"> + <dia:attribute name="obj_pos"> + <dia:point val="39.5337,11.2917"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="24.0713,9.92418;39.5878,11.3458"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="39.5337,11.2917"/> + <dia:point val="24.1254,9.97825"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O15" connection="2"/> + <dia:connection handle="1" to="O12" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O20"> + <dia:attribute name="obj_pos"> + <dia:point val="39.98,12.0742"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="39.93,12.0242;40.88,12.9742"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="39.98,12.0742"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O21"> + <dia:attribute name="obj_pos"> + <dia:point val="40.83,12.4992"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="40.78,12.1388;49.2453,12.8624"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="40.83,12.4992"/> + <dia:point val="49.1335,12.5007"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O20" connection="3"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O22"> + <dia:attribute name="obj_pos"> + <dia:point val="42.0954,11.99"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="42.0954,11.395;46.7404,12.1425"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 1 (source)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="42.0954,11.99"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O23"> + <dia:attribute name="obj_pos"> + <dia:point val="-1.44491,11.6506"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-1.49491,11.6006;-0.54491,12.5506"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="-1.44491,11.6506"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O24"> + <dia:attribute name="obj_pos"> + <dia:point val="-9.61991,12.09"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-9.67,11.7149;-1.33311,12.4385"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="-9.61991,12.09"/> + <dia:point val="-1.44491,12.0756"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O23" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O25"> + <dia:attribute name="obj_pos"> + <dia:point val="-7.39291,11.49"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="-7.39291,10.895;-3.58791,11.6425"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 0 (sink)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="-7.39291,11.49"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O26"> + <dia:attribute name="obj_pos"> + <dia:point val="19.4911,13.8333"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="19.4411,13.7833;24.5504,17.4559"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="19.4911,13.8333"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="5.009308462554376"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.5726155970598077"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="false"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Box" version="0" id="O27"> + <dia:attribute name="obj_pos"> + <dia:point val="34.4994,17.2967"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="34.4494,17.2467;39.5587,20.9193"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="34.4994,17.2967"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="5.009308462554376"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="3.5726155970598077"/> + </dia:attribute> + <dia:attribute name="border_width"> + <dia:real val="0.10000000149011612"/> + </dia:attribute> + <dia:attribute name="border_color"> + <dia:color val="#8b6914"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O28"> + <dia:attribute name="obj_pos"> + <dia:point val="34.4994,20.8693"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="19.4311,17.3459;34.5594,20.9293"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="34.4994,20.8693"/> + <dia:point val="19.4911,17.4059"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O27" connection="5"/> + <dia:connection handle="1" to="O26" connection="5"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O29"> + <dia:attribute name="obj_pos"> + <dia:point val="34.4994,17.2967"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="19.4311,13.7733;34.5594,17.3567"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="34.4994,17.2967"/> + <dia:point val="19.4911,13.8333"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O27" connection="0"/> + <dia:connection handle="1" to="O26" connection="0"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O30"> + <dia:attribute name="obj_pos"> + <dia:point val="39.5087,20.8693"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="24.4404,17.3459;39.5687,20.9293"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="39.5087,20.8693"/> + <dia:point val="24.5004,17.4059"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O27" connection="7"/> + <dia:connection handle="1" to="O26" connection="7"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O31"> + <dia:attribute name="obj_pos"> + <dia:point val="39.5087,17.2967"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="24.4404,13.7733;39.5687,17.3567"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="39.5087,17.2967"/> + <dia:point val="24.5004,13.8333"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#e60505"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="4"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O27" connection="2"/> + <dia:connection handle="1" to="O26" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Geometric - Perfect Circle" version="1" id="O32"> + <dia:attribute name="obj_pos"> + <dia:point val="39.855,18.7792"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="39.805,18.7292;40.755,19.6792"/> + </dia:attribute> + <dia:attribute name="meta"> + <dia:composite type="dict"/> + </dia:attribute> + <dia:attribute name="elem_corner"> + <dia:point val="39.855,18.7792"/> + </dia:attribute> + <dia:attribute name="elem_width"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="elem_height"> + <dia:real val="0.84999999999999787"/> + </dia:attribute> + <dia:attribute name="line_width"> + <dia:real val="0.10000000000000001"/> + </dia:attribute> + <dia:attribute name="line_colour"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="fill_colour"> + <dia:color val="#ffffff"/> + </dia:attribute> + <dia:attribute name="show_background"> + <dia:boolean val="true"/> + </dia:attribute> + <dia:attribute name="line_style"> + <dia:enum val="0"/> + <dia:real val="1"/> + </dia:attribute> + <dia:attribute name="flip_horizontal"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="flip_vertical"> + <dia:boolean val="false"/> + </dia:attribute> + <dia:attribute name="subscale"> + <dia:real val="1"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O33"> + <dia:attribute name="obj_pos"> + <dia:point val="40.705,19.2042"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="40.655,18.8438;49.1203,19.5674"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="40.705,19.2042"/> + <dia:point val="49.0085,19.2057"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="0" to="O32" connection="3"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Text" version="1" id="O34"> + <dia:attribute name="obj_pos"> + <dia:point val="41.9704,18.695"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="41.9704,18.1;46.6154,18.8475"/> + </dia:attribute> + <dia:attribute name="text"> + <dia:composite type="text"> + <dia:attribute name="string"> + <dia:string>#pad 2 (source)#</dia:string> + </dia:attribute> + <dia:attribute name="font"> + <dia:font family="sans" style="0" name="Helvetica"/> + </dia:attribute> + <dia:attribute name="height"> + <dia:real val="0.80000000000000004"/> + </dia:attribute> + <dia:attribute name="pos"> + <dia:point val="41.9704,18.695"/> + </dia:attribute> + <dia:attribute name="color"> + <dia:color val="#000000"/> + </dia:attribute> + <dia:attribute name="alignment"> + <dia:enum val="0"/> + </dia:attribute> + </dia:composite> + </dia:attribute> + <dia:attribute name="valign"> + <dia:enum val="3"/> + </dia:attribute> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O35"> + <dia:attribute name="obj_pos"> + <dia:point val="27.3,9.55"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="24.0146,9.49376;27.3562,10.255"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="27.3,9.55"/> + <dia:point val="24.1254,9.97825"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O12" connection="2"/> + </dia:connections> + </dia:object> + <dia:object type="Standard - Line" version="0" id="O36"> + <dia:attribute name="obj_pos"> + <dia:point val="27.3454,9.53624"/> + </dia:attribute> + <dia:attribute name="obj_bb"> + <dia:rectangle val="24.4311,9.46695;27.4147,13.9265"/> + </dia:attribute> + <dia:attribute name="conn_endpoints"> + <dia:point val="27.3454,9.53624"/> + <dia:point val="24.5004,13.8333"/> + </dia:attribute> + <dia:attribute name="numcp"> + <dia:int val="1"/> + </dia:attribute> + <dia:attribute name="line_color"> + <dia:color val="#a020f0"/> + </dia:attribute> + <dia:attribute name="end_arrow"> + <dia:enum val="22"/> + </dia:attribute> + <dia:attribute name="end_arrow_length"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:attribute name="end_arrow_width"> + <dia:real val="0.5"/> + </dia:attribute> + <dia:connections> + <dia:connection handle="1" to="O26" connection="2"/> + </dia:connections> + </dia:object> + </dia:layer> +</dia:diagram> diff --git a/Documentation/DocBook/media/v4l/subdev-image-processing-scaling-multi-source.svg b/Documentation/DocBook/media/v4l/subdev-image-processing-scaling-multi-source.svg new file mode 100644 index 000000000000..2340c0f8bc92 --- /dev/null +++ b/Documentation/DocBook/media/v4l/subdev-image-processing-scaling-multi-source.svg @@ -0,0 +1,116 @@ +<?xml version="1.0" encoding="UTF-8" standalone="no"?> +<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.0//EN" "http://www.w3.org/TR/2001/PR-SVG-20010719/DTD/svg10.dtd"> +<svg width="59cm" height="17cm" viewBox="-194 128 1179 330" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink"> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="-8" y="130" width="806" height="327"/> + <g> + <rect style="fill: #ffffff" x="4.5" y="189" width="159" height="104"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a52a2a" x="4.5" y="189" width="159" height="104"/> + </g> + <g> + <rect style="fill: #ffffff" x="49.5" y="204" width="94" height="77"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #0000ff" x="49.5" y="204" width="94" height="77"/> + </g> + <text style="fill: #0000ff;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="60" y="224"> + <tspan x="60" y="224">sink</tspan> + <tspan x="60" y="240">crop</tspan> + <tspan x="60" y="256">selection</tspan> + </text> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="29.5" y="158"> + <tspan x="29.5" y="158"></tspan> + </text> + <text style="fill: #a52a2a;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="8.53836" y="157.914"> + <tspan x="8.53836" y="157.914">sink media</tspan> + <tspan x="8.53836" y="173.914">bus format</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="333.644" y="185.65" width="165.2" height="172.478"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #00ff00" x="333.644" y="185.65" width="165.2" height="172.478"/> + </g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="333.644" y1="358.128" x2="49.5" y2="281"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="333.644" y1="185.65" x2="49.5" y2="204"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="498.844" y1="358.128" x2="143.5" y2="281"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="498.844" y1="185.65" x2="143.5" y2="204"/> + <text style="fill: #00ff00;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="334.704" y="149.442"> + <tspan x="334.704" y="149.442">sink compose</tspan> + <tspan x="334.704" y="165.442">selection (scaling)</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="382.322" y="199.565" width="100.186" height="71.4523"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" x="382.322" y="199.565" width="100.186" height="71.4523"/> + </g> + <text style="fill: #a020f0;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="543.322" y="149.442"> + <tspan x="543.322" y="149.442">source</tspan> + <tspan x="543.322" y="165.442">crop</tspan> + <tspan x="543.322" y="181.442">selection</tspan> + </text> + <text style="fill: #8b6914;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="691.5" y="157.128"> + <tspan x="691.5" y="157.128">source media</tspan> + <tspan x="691.5" y="173.128">bus format</tspan> + </text> + <g> + <rect style="fill: #ffffff" x="690.488" y="225.834" width="100.186" height="71.4523"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #8b6914" x="690.488" y="225.834" width="100.186" height="71.4523"/> + </g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="690.488" y1="297.286" x2="382.322" y2="271.018"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="690.488" y1="225.834" x2="382.322" y2="199.565"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="790.674" y1="297.286" x2="482.508" y2="271.018"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="790.674" y1="225.834" x2="482.508" y2="199.565"/> + <g> + <ellipse style="fill: #ffffff" cx="808.1" cy="249.984" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="808.1" cy="249.984" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="808.1" cy="249.984" rx="8.5" ry="8.5"/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="816.6" y1="249.984" x2="972.934" y2="250.012"/> + <polygon style="fill: #000000" points="980.434,250.014 970.433,255.012 972.934,250.012 970.435,245.012 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="980.434,250.014 970.433,255.012 972.934,250.012 970.435,245.012 "/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="841.908" y="239.8"> + <tspan x="841.908" y="239.8">pad 1 (source)</tspan> + </text> + <g> + <ellipse style="fill: #ffffff" cx="-20.3982" cy="241.512" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="-20.3982" cy="241.512" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="-20.3982" cy="241.512" rx="8.5" ry="8.5"/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="-192.398" y1="241.8" x2="-38.6343" y2="241.529"/> + <polygon style="fill: #000000" points="-31.1343,241.516 -41.1254,246.534 -38.6343,241.529 -41.1431,236.534 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="-31.1343,241.516 -41.1254,246.534 -38.6343,241.529 -41.1431,236.534 "/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="-147.858" y="229.8"> + <tspan x="-147.858" y="229.8">pad 0 (sink)</tspan> + </text> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" x="389.822" y="276.666" width="100.186" height="71.4523"/> + <g> + <rect style="fill: #ffffff" x="689.988" y="345.934" width="100.186" height="71.4523"/> + <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #8b6914" x="689.988" y="345.934" width="100.186" height="71.4523"/> + </g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="689.988" y1="417.386" x2="389.822" y2="348.118"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="689.988" y1="345.934" x2="389.822" y2="276.666"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="790.174" y1="417.386" x2="490.008" y2="348.118"/> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #e60505" x1="790.174" y1="345.934" x2="490.008" y2="276.666"/> + <g> + <ellipse style="fill: #ffffff" cx="805.6" cy="384.084" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="805.6" cy="384.084" rx="8.5" ry="8.5"/> + <ellipse style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" cx="805.6" cy="384.084" rx="8.5" ry="8.5"/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x1="814.1" y1="384.084" x2="970.434" y2="384.112"/> + <polygon style="fill: #000000" points="977.934,384.114 967.933,389.112 970.434,384.112 967.935,379.112 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" points="977.934,384.114 967.933,389.112 970.434,384.112 967.935,379.112 "/> + </g> + <text style="fill: #000000;text-anchor:start;font-size:12.8;font-family:sanserif;font-style:normal;font-weight:normal" x="839.408" y="373.9"> + <tspan x="839.408" y="373.9">pad 2 (source)</tspan> + </text> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" x1="546" y1="191" x2="492.157" y2="198.263"/> + <polygon style="fill: #a020f0" points="484.724,199.266 493.966,192.974 492.157,198.263 495.303,202.884 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" points="484.724,199.266 493.966,192.974 492.157,198.263 495.303,202.884 "/> + </g> + <g> + <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" x1="546.908" y1="190.725" x2="495.383" y2="268.548"/> + <polygon style="fill: #a020f0" points="491.242,274.802 492.594,263.703 495.383,268.548 500.932,269.224 "/> + <polygon style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #a020f0" points="491.242,274.802 492.594,263.703 495.383,268.548 500.932,269.224 "/> + </g> +</svg> diff --git a/Documentation/DocBook/media/v4l/v4l2.xml b/Documentation/DocBook/media/v4l/v4l2.xml index 8ae38876172e..015c561754b7 100644 --- a/Documentation/DocBook/media/v4l/v4l2.xml +++ b/Documentation/DocBook/media/v4l/v4l2.xml @@ -28,8 +28,8 @@ documentation.</contrib> <firstname>Hans</firstname> <surname>Verkuil</surname> <contrib>Designed and documented the VIDIOC_LOG_STATUS ioctl, -the extended control ioctls and major parts of the sliced VBI -API.</contrib> +the extended control ioctls, major parts of the sliced VBI API, the +MPEG encoder and decoder APIs and the DV Timings API.</contrib> <affiliation> <address> <email>hverkuil@xs4all.nl</email> @@ -96,6 +96,17 @@ Remote Controller chapter.</contrib> </address> </affiliation> </author> + + <author> + <firstname>Sakari</firstname> + <surname>Ailus</surname> + <contrib>Subdev selections API.</contrib> + <affiliation> + <address> + <email>sakari.ailus@iki.fi</email> + </address> + </affiliation> + </author> </authorgroup> <copyright> @@ -112,6 +123,7 @@ Remote Controller chapter.</contrib> <year>2009</year> <year>2010</year> <year>2011</year> + <year>2012</year> <holder>Bill Dirks, Michael H. Schimek, Hans Verkuil, Martin Rubli, Andy Walls, Muralidharan Karicheri, Mauro Carvalho Chehab, Pawel Osciak</holder> @@ -128,6 +140,28 @@ structs, ioctls) must be noted in more detail in the history chapter applications. --> <revision> + <revnumber>3.5</revnumber> + <date>2012-05-07</date> + <authorinitials>sa, sn</authorinitials> + <revremark>Added V4L2_CTRL_TYPE_INTEGER_MENU and V4L2 subdev + selections API. Improved the description of V4L2_CID_COLORFX + control, added V4L2_CID_COLORFX_CBCR control. + Added camera controls V4L2_CID_AUTO_EXPOSURE_BIAS, + V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE, V4L2_CID_IMAGE_STABILIZATION, + V4L2_CID_ISO_SENSITIVITY, V4L2_CID_ISO_SENSITIVITY_AUTO, + V4L2_CID_EXPOSURE_METERING, V4L2_CID_SCENE_MODE, + V4L2_CID_3A_LOCK, V4L2_CID_AUTO_FOCUS_START, + V4L2_CID_AUTO_FOCUS_STOP, V4L2_CID_AUTO_FOCUS_STATUS + and V4L2_CID_AUTO_FOCUS_RANGE. + </revremark> + <date>2012-05-01</date> + <authorinitials>hv</authorinitials> + <revremark>Added VIDIOC_ENUM_DV_TIMINGS, VIDIOC_QUERY_DV_TIMINGS and + VIDIOC_DV_TIMINGS_CAP. + </revremark> + </revision> + + <revision> <revnumber>3.4</revnumber> <date>2012-01-25</date> <authorinitials>sn</authorinitials> @@ -433,7 +467,7 @@ and discussions on the V4L mailing list.</revremark> </partinfo> <title>Video for Linux Two API Specification</title> - <subtitle>Revision 3.3</subtitle> + <subtitle>Revision 3.5</subtitle> <chapter id="common"> &sub-common; @@ -491,10 +525,12 @@ and discussions on the V4L mailing list.</revremark> &sub-dbg-g-register; &sub-decoder-cmd; &sub-dqevent; + &sub-dv-timings-cap; &sub-encoder-cmd; &sub-enumaudio; &sub-enumaudioout; &sub-enum-dv-presets; + &sub-enum-dv-timings; &sub-enum-fmt; &sub-enum-framesizes; &sub-enum-frameintervals; @@ -529,6 +565,7 @@ and discussions on the V4L mailing list.</revremark> &sub-querycap; &sub-queryctrl; &sub-query-dv-preset; + &sub-query-dv-timings; &sub-querystd; &sub-prepare-buf; &sub-reqbufs; @@ -540,6 +577,7 @@ and discussions on the V4L mailing list.</revremark> &sub-subdev-g-crop; &sub-subdev-g-fmt; &sub-subdev-g-frame-interval; + &sub-subdev-g-selection; &sub-subscribe-event; <!-- End of ioctls. --> &sub-mmap; diff --git a/Documentation/DocBook/media/v4l/vidioc-create-bufs.xml b/Documentation/DocBook/media/v4l/vidioc-create-bufs.xml index 73ae8a6cd004..765549ff8a71 100644 --- a/Documentation/DocBook/media/v4l/vidioc-create-bufs.xml +++ b/Documentation/DocBook/media/v4l/vidioc-create-bufs.xml @@ -48,6 +48,12 @@ <refsect1> <title>Description</title> + <note> + <title>Experimental</title> + <para>This is an <link linkend="experimental"> experimental </link> + interface and may change in the future.</para> + </note> + <para>This ioctl is used to create buffers for <link linkend="mmap">memory mapped</link> or <link linkend="userp">user pointer</link> I/O. It can be used as an alternative or in addition to the @@ -94,16 +100,18 @@ information.</para> <entry>The number of buffers requested or granted.</entry> </row> <row> - <entry>&v4l2-memory;</entry> + <entry>__u32</entry> <entry><structfield>memory</structfield></entry> <entry>Applications set this field to <constant>V4L2_MEMORY_MMAP</constant> or -<constant>V4L2_MEMORY_USERPTR</constant>.</entry> +<constant>V4L2_MEMORY_USERPTR</constant>. See <xref linkend="v4l2-memory" +/></entry> </row> <row> - <entry>&v4l2-format;</entry> + <entry>__u32</entry> <entry><structfield>format</structfield></entry> - <entry>Filled in by the application, preserved by the driver.</entry> + <entry>Filled in by the application, preserved by the driver. + See <xref linkend="v4l2-format" />.</entry> </row> <row> <entry>__u32</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-cropcap.xml b/Documentation/DocBook/media/v4l/vidioc-cropcap.xml index b4f2f255211e..f1bac2c6e978 100644 --- a/Documentation/DocBook/media/v4l/vidioc-cropcap.xml +++ b/Documentation/DocBook/media/v4l/vidioc-cropcap.xml @@ -65,7 +65,7 @@ output.</para> &cs-str; <tbody valign="top"> <row> - <entry>&v4l2-buf-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry>Type of the data stream, set by the application. Only these types are valid here: @@ -73,7 +73,7 @@ Only these types are valid here: <constant>V4L2_BUF_TYPE_VIDEO_OUTPUT</constant>, <constant>V4L2_BUF_TYPE_VIDEO_OVERLAY</constant>, and custom (driver defined) types with code <constant>V4L2_BUF_TYPE_PRIVATE</constant> -and higher.</entry> +and higher. See <xref linkend="v4l2-buf-type" />.</entry> </row> <row> <entry>struct <link linkend="v4l2-rect-crop">v4l2_rect</link></entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-dv-timings-cap.xml b/Documentation/DocBook/media/v4l/vidioc-dv-timings-cap.xml new file mode 100644 index 000000000000..6673ce582050 --- /dev/null +++ b/Documentation/DocBook/media/v4l/vidioc-dv-timings-cap.xml @@ -0,0 +1,211 @@ +<refentry id="vidioc-dv-timings-cap"> + <refmeta> + <refentrytitle>ioctl VIDIOC_DV_TIMINGS_CAP</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>VIDIOC_DV_TIMINGS_CAP</refname> + <refpurpose>The capabilities of the Digital Video receiver/transmitter</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>struct v4l2_dv_timings_cap *<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>&fd;</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>VIDIOC_DV_TIMINGS_CAP</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + + <note> + <title>Experimental</title> + <para>This is an <link linkend="experimental"> experimental </link> + interface and may change in the future.</para> + </note> + + <para>To query the available timings, applications initialize the +<structfield>index</structfield> field and zero the reserved array of &v4l2-dv-timings-cap; +and call the <constant>VIDIOC_DV_TIMINGS_CAP</constant> ioctl with a pointer to this +structure. Drivers fill the rest of the structure or return an +&EINVAL; when the index is out of bounds. To enumerate all supported DV timings, +applications shall begin at index zero, incrementing by one until the +driver returns <errorcode>EINVAL</errorcode>. Note that drivers may enumerate a +different set of DV timings after switching the video input or +output.</para> + + <table pgwide="1" frame="none" id="v4l2-bt-timings-cap"> + <title>struct <structname>v4l2_bt_timings_cap</structname></title> + <tgroup cols="3"> + &cs-str; + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>min_width</structfield></entry> + <entry>Minimum width of the active video in pixels.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>max_width</structfield></entry> + <entry>Maximum width of the active video in pixels.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>min_height</structfield></entry> + <entry>Minimum height of the active video in lines.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>max_height</structfield></entry> + <entry>Maximum height of the active video in lines.</entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>min_pixelclock</structfield></entry> + <entry>Minimum pixelclock frequency in Hz.</entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>max_pixelclock</structfield></entry> + <entry>Maximum pixelclock frequency in Hz.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>standards</structfield></entry> + <entry>The video standard(s) supported by the hardware. + See <xref linkend="dv-bt-standards"/> for a list of standards.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>capabilities</structfield></entry> + <entry>Several flags giving more information about the capabilities. + See <xref linkend="dv-bt-cap-capabilities"/> for a description of the flags. + </entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[16]</entry> + <entry></entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="v4l2-dv-timings-cap"> + <title>struct <structname>v4l2_dv_timings_cap</structname></title> + <tgroup cols="4"> + &cs-str; + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>type</structfield></entry> + <entry>Type of DV timings as listed in <xref linkend="dv-timing-types"/>.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[3]</entry> + <entry>Reserved for future extensions. Drivers must set the array to zero.</entry> + </row> + <row> + <entry>union</entry> + <entry><structfield></structfield></entry> + <entry></entry> + </row> + <row> + <entry></entry> + <entry>&v4l2-bt-timings-cap;</entry> + <entry><structfield>bt</structfield></entry> + <entry>BT.656/1120 timings capabilities of the hardware.</entry> + </row> + <row> + <entry></entry> + <entry>__u32</entry> + <entry><structfield>raw_data</structfield>[32]</entry> + <entry></entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="dv-bt-cap-capabilities"> + <title>DV BT Timing capabilities</title> + <tgroup cols="2"> + &cs-str; + <tbody valign="top"> + <row> + <entry>Flag</entry> + <entry>Description</entry> + </row> + <row> + <entry></entry> + <entry></entry> + </row> + <row> + <entry>V4L2_DV_BT_CAP_INTERLACED</entry> + <entry>Interlaced formats are supported. + </entry> + </row> + <row> + <entry>V4L2_DV_BT_CAP_PROGRESSIVE</entry> + <entry>Progressive formats are supported. + </entry> + </row> + <row> + <entry>V4L2_DV_BT_CAP_REDUCED_BLANKING</entry> + <entry>CVT/GTF specific: the timings can make use of reduced blanking (CVT) +or the 'Secondary GTF' curve (GTF). + </entry> + </row> + <row> + <entry>V4L2_DV_BT_CAP_CUSTOM</entry> + <entry>Can support non-standard timings, i.e. timings not belonging to the +standards set in the <structfield>standards</structfield> field. + </entry> + </row> + </tbody> + </tgroup> + </table> + </refsect1> + + <refsect1> + &return-value; + </refsect1> +</refentry> + +<!-- +Local Variables: +mode: sgml +sgml-parent-document: "v4l2.sgml" +indent-tabs-mode: nil +End: +--> diff --git a/Documentation/DocBook/media/v4l/vidioc-enum-dv-presets.xml b/Documentation/DocBook/media/v4l/vidioc-enum-dv-presets.xml index 0be17c232d3a..509f0012d2a6 100644 --- a/Documentation/DocBook/media/v4l/vidioc-enum-dv-presets.xml +++ b/Documentation/DocBook/media/v4l/vidioc-enum-dv-presets.xml @@ -48,6 +48,10 @@ <refsect1> <title>Description</title> + <para>This ioctl is <emphasis role="bold">deprecated</emphasis>. + New drivers and applications should use &VIDIOC-ENUM-DV-TIMINGS; instead. + </para> + <para>To query the attributes of a DV preset, applications initialize the <structfield>index</structfield> field and zero the reserved array of &v4l2-dv-enum-preset; and call the <constant>VIDIOC_ENUM_DV_PRESETS</constant> ioctl with a pointer to this diff --git a/Documentation/DocBook/media/v4l/vidioc-enum-dv-timings.xml b/Documentation/DocBook/media/v4l/vidioc-enum-dv-timings.xml new file mode 100644 index 000000000000..24c3bf4fd29a --- /dev/null +++ b/Documentation/DocBook/media/v4l/vidioc-enum-dv-timings.xml @@ -0,0 +1,119 @@ +<refentry id="vidioc-enum-dv-timings"> + <refmeta> + <refentrytitle>ioctl VIDIOC_ENUM_DV_TIMINGS</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>VIDIOC_ENUM_DV_TIMINGS</refname> + <refpurpose>Enumerate supported Digital Video timings</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>struct v4l2_enum_dv_timings *<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>&fd;</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>VIDIOC_ENUM_DV_TIMINGS</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + + <note> + <title>Experimental</title> + <para>This is an <link linkend="experimental"> experimental </link> + interface and may change in the future.</para> + </note> + + <para>While some DV receivers or transmitters support a wide range of timings, others +support only a limited number of timings. With this ioctl applications can enumerate a list +of known supported timings. Call &VIDIOC-DV-TIMINGS-CAP; to check if it also supports other +standards or even custom timings that are not in this list.</para> + + <para>To query the available timings, applications initialize the +<structfield>index</structfield> field and zero the reserved array of &v4l2-enum-dv-timings; +and call the <constant>VIDIOC_ENUM_DV_TIMINGS</constant> ioctl with a pointer to this +structure. Drivers fill the rest of the structure or return an +&EINVAL; when the index is out of bounds. To enumerate all supported DV timings, +applications shall begin at index zero, incrementing by one until the +driver returns <errorcode>EINVAL</errorcode>. Note that drivers may enumerate a +different set of DV timings after switching the video input or +output.</para> + + <table pgwide="1" frame="none" id="v4l2-enum-dv-timings"> + <title>struct <structname>v4l2_enum_dv_timings</structname></title> + <tgroup cols="3"> + &cs-str; + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>index</structfield></entry> + <entry>Number of the DV timings, set by the +application.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[3]</entry> + <entry>Reserved for future extensions. Drivers must set the array to zero.</entry> + </row> + <row> + <entry>&v4l2-dv-timings;</entry> + <entry><structfield>timings</structfield></entry> + <entry>The timings.</entry> + </row> + </tbody> + </tgroup> + </table> + </refsect1> + + <refsect1> + &return-value; + + <variablelist> + <varlistentry> + <term><errorcode>EINVAL</errorcode></term> + <listitem> + <para>The &v4l2-enum-dv-timings; <structfield>index</structfield> +is out of bounds.</para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> +</refentry> + +<!-- +Local Variables: +mode: sgml +sgml-parent-document: "v4l2.sgml" +indent-tabs-mode: nil +End: +--> diff --git a/Documentation/DocBook/media/v4l/vidioc-enum-fmt.xml b/Documentation/DocBook/media/v4l/vidioc-enum-fmt.xml index 347d142e7431..81ebe48317fe 100644 --- a/Documentation/DocBook/media/v4l/vidioc-enum-fmt.xml +++ b/Documentation/DocBook/media/v4l/vidioc-enum-fmt.xml @@ -71,7 +71,7 @@ the application. This is in no way related to the <structfield> pixelformat</structfield> field.</entry> </row> <row> - <entry>&v4l2-buf-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry>Type of the data stream, set by the application. Only these types are valid here: @@ -81,7 +81,7 @@ Only these types are valid here: <constant>V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE</constant>, <constant>V4L2_BUF_TYPE_VIDEO_OVERLAY</constant>, and custom (driver defined) types with code <constant>V4L2_BUF_TYPE_PRIVATE</constant> -and higher.</entry> +and higher. See <xref linkend="v4l2-buf-type" />.</entry> </row> <row> <entry>__u32</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-enuminput.xml b/Documentation/DocBook/media/v4l/vidioc-enuminput.xml index 9b8efcd6e947..46d5a044a537 100644 --- a/Documentation/DocBook/media/v4l/vidioc-enuminput.xml +++ b/Documentation/DocBook/media/v4l/vidioc-enuminput.xml @@ -285,7 +285,7 @@ input/output interface to linux-media@vger.kernel.org on 19 Oct 2009. <row> <entry><constant>V4L2_IN_CAP_CUSTOM_TIMINGS</constant></entry> <entry>0x00000002</entry> - <entry>This input supports setting custom video timings by using VIDIOC_S_DV_TIMINGS.</entry> + <entry>This input supports setting video timings by using VIDIOC_S_DV_TIMINGS.</entry> </row> <row> <entry><constant>V4L2_IN_CAP_STD</constant></entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-enumoutput.xml b/Documentation/DocBook/media/v4l/vidioc-enumoutput.xml index a64d5ef103fa..428020000ef0 100644 --- a/Documentation/DocBook/media/v4l/vidioc-enumoutput.xml +++ b/Documentation/DocBook/media/v4l/vidioc-enumoutput.xml @@ -170,7 +170,7 @@ input/output interface to linux-media@vger.kernel.org on 19 Oct 2009. <row> <entry><constant>V4L2_OUT_CAP_CUSTOM_TIMINGS</constant></entry> <entry>0x00000002</entry> - <entry>This output supports setting custom video timings by using VIDIOC_S_DV_TIMINGS.</entry> + <entry>This output supports setting video timings by using VIDIOC_S_DV_TIMINGS.</entry> </row> <row> <entry><constant>V4L2_OUT_CAP_STD</constant></entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-g-crop.xml b/Documentation/DocBook/media/v4l/vidioc-g-crop.xml index 01a50640dce0..c4ff3b1887fb 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-crop.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-crop.xml @@ -100,14 +100,14 @@ changed and <constant>VIDIOC_S_CROP</constant> returns the &cs-str; <tbody valign="top"> <row> - <entry>&v4l2-buf-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry>Type of the data stream, set by the application. Only these types are valid here: <constant>V4L2_BUF_TYPE_VIDEO_CAPTURE</constant>, <constant>V4L2_BUF_TYPE_VIDEO_OUTPUT</constant>, <constant>V4L2_BUF_TYPE_VIDEO_OVERLAY</constant>, and custom (driver defined) types with code <constant>V4L2_BUF_TYPE_PRIVATE</constant> -and higher.</entry> +and higher. See <xref linkend="v4l2-buf-type" />.</entry> </row> <row> <entry>&v4l2-rect;</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-g-dv-preset.xml b/Documentation/DocBook/media/v4l/vidioc-g-dv-preset.xml index 7940c1149393..61be9fa3803a 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-dv-preset.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-dv-preset.xml @@ -48,6 +48,12 @@ <refsect1> <title>Description</title> + + <para>These ioctls are <emphasis role="bold">deprecated</emphasis>. + New drivers and applications should use &VIDIOC-G-DV-TIMINGS; and &VIDIOC-S-DV-TIMINGS; + instead. + </para> + <para>To query and select the current DV preset, applications use the <constant>VIDIOC_G_DV_PRESET</constant> and <constant>VIDIOC_S_DV_PRESET</constant> ioctls which take a pointer to a &v4l2-dv-preset; type as argument. diff --git a/Documentation/DocBook/media/v4l/vidioc-g-dv-timings.xml b/Documentation/DocBook/media/v4l/vidioc-g-dv-timings.xml index 4a8648ae9a63..eda1a2991bbe 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-dv-timings.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-dv-timings.xml @@ -7,7 +7,7 @@ <refnamediv> <refname>VIDIOC_G_DV_TIMINGS</refname> <refname>VIDIOC_S_DV_TIMINGS</refname> - <refpurpose>Get or set custom DV timings for input or output</refpurpose> + <refpurpose>Get or set DV timings for input or output</refpurpose> </refnamediv> <refsynopsisdiv> @@ -48,12 +48,15 @@ <refsect1> <title>Description</title> - <para>To set custom DV timings for the input or output, applications use the -<constant>VIDIOC_S_DV_TIMINGS</constant> ioctl and to get the current custom timings, + <para>To set DV timings for the input or output, applications use the +<constant>VIDIOC_S_DV_TIMINGS</constant> ioctl and to get the current timings, applications use the <constant>VIDIOC_G_DV_TIMINGS</constant> ioctl. The detailed timing information is filled in using the structure &v4l2-dv-timings;. These ioctls take a pointer to the &v4l2-dv-timings; structure as argument. If the ioctl is not supported or the timing values are not correct, the driver returns &EINVAL;.</para> +<para>The <filename>linux/v4l2-dv-timings.h</filename> header can be used to get the +timings of the formats in the <xref linkend="cea861" /> and <xref linkend="vesadmt" /> +standards.</para> </refsect1> <refsect1> @@ -83,12 +86,13 @@ or the timing values are not correct, the driver returns &EINVAL;.</para> <row> <entry>__u32</entry> <entry><structfield>width</structfield></entry> - <entry>Width of the active video in pixels</entry> + <entry>Width of the active video in pixels.</entry> </row> <row> <entry>__u32</entry> <entry><structfield>height</structfield></entry> - <entry>Height of the active video in lines</entry> + <entry>Height of the active video frame in lines. So for interlaced formats the + height of the active video in each field is <structfield>height</structfield>/2.</entry> </row> <row> <entry>__u32</entry> @@ -125,32 +129,52 @@ bit 0 (V4L2_DV_VSYNC_POS_POL) is for vertical sync polarity and bit 1 (V4L2_DV_H <row> <entry>__u32</entry> <entry><structfield>vfrontporch</structfield></entry> - <entry>Vertical front porch in lines</entry> + <entry>Vertical front porch in lines. For interlaced formats this refers to the + odd field (aka field 1).</entry> </row> <row> <entry>__u32</entry> <entry><structfield>vsync</structfield></entry> - <entry>Vertical sync length in lines</entry> + <entry>Vertical sync length in lines. For interlaced formats this refers to the + odd field (aka field 1).</entry> </row> <row> <entry>__u32</entry> <entry><structfield>vbackporch</structfield></entry> - <entry>Vertical back porch in lines</entry> + <entry>Vertical back porch in lines. For interlaced formats this refers to the + odd field (aka field 1).</entry> </row> <row> <entry>__u32</entry> <entry><structfield>il_vfrontporch</structfield></entry> - <entry>Vertical front porch in lines for bottom field of interlaced field formats</entry> + <entry>Vertical front porch in lines for the even field (aka field 2) of + interlaced field formats.</entry> </row> <row> <entry>__u32</entry> <entry><structfield>il_vsync</structfield></entry> - <entry>Vertical sync length in lines for bottom field of interlaced field formats</entry> + <entry>Vertical sync length in lines for the even field (aka field 2) of + interlaced field formats.</entry> </row> <row> <entry>__u32</entry> <entry><structfield>il_vbackporch</structfield></entry> - <entry>Vertical back porch in lines for bottom field of interlaced field formats</entry> + <entry>Vertical back porch in lines for the even field (aka field 2) of + interlaced field formats.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>standards</structfield></entry> + <entry>The video standard(s) this format belongs to. This will be filled in by + the driver. Applications must set this to 0. See <xref linkend="dv-bt-standards"/> + for a list of standards.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>flags</structfield></entry> + <entry>Several flags giving more information about the format. + See <xref linkend="dv-bt-flags"/> for a description of the flags. + </entry> </row> </tbody> </tgroup> @@ -211,6 +235,90 @@ bit 0 (V4L2_DV_VSYNC_POS_POL) is for vertical sync polarity and bit 1 (V4L2_DV_H </tbody> </tgroup> </table> + <table pgwide="1" frame="none" id="dv-bt-standards"> + <title>DV BT Timing standards</title> + <tgroup cols="2"> + &cs-str; + <tbody valign="top"> + <row> + <entry>Timing standard</entry> + <entry>Description</entry> + </row> + <row> + <entry></entry> + <entry></entry> + </row> + <row> + <entry>V4L2_DV_BT_STD_CEA861</entry> + <entry>The timings follow the CEA-861 Digital TV Profile standard</entry> + </row> + <row> + <entry>V4L2_DV_BT_STD_DMT</entry> + <entry>The timings follow the VESA Discrete Monitor Timings standard</entry> + </row> + <row> + <entry>V4L2_DV_BT_STD_CVT</entry> + <entry>The timings follow the VESA Coordinated Video Timings standard</entry> + </row> + <row> + <entry>V4L2_DV_BT_STD_GTF</entry> + <entry>The timings follow the VESA Generalized Timings Formula standard</entry> + </row> + </tbody> + </tgroup> + </table> + <table pgwide="1" frame="none" id="dv-bt-flags"> + <title>DV BT Timing flags</title> + <tgroup cols="2"> + &cs-str; + <tbody valign="top"> + <row> + <entry>Flag</entry> + <entry>Description</entry> + </row> + <row> + <entry></entry> + <entry></entry> + </row> + <row> + <entry>V4L2_DV_FL_REDUCED_BLANKING</entry> + <entry>CVT/GTF specific: the timings use reduced blanking (CVT) or the 'Secondary +GTF' curve (GTF). In both cases the horizontal and/or vertical blanking +intervals are reduced, allowing a higher resolution over the same +bandwidth. This is a read-only flag, applications must not set this. + </entry> + </row> + <row> + <entry>V4L2_DV_FL_CAN_REDUCE_FPS</entry> + <entry>CEA-861 specific: set for CEA-861 formats with a framerate that is a multiple +of six. These formats can be optionally played at 1 / 1.001 speed to +be compatible with 60 Hz based standards such as NTSC and PAL-M that use a framerate of +29.97 frames per second. If the transmitter can't generate such frequencies, then the +flag will also be cleared. This is a read-only flag, applications must not set this. + </entry> + </row> + <row> + <entry>V4L2_DV_FL_REDUCED_FPS</entry> + <entry>CEA-861 specific: only valid for video transmitters, the flag is cleared +by receivers. It is also only valid for formats with the V4L2_DV_FL_CAN_REDUCE_FPS flag +set, for other formats the flag will be cleared by the driver. + +If the application sets this flag, then the pixelclock used to set up the transmitter is +divided by 1.001 to make it compatible with NTSC framerates. If the transmitter +can't generate such frequencies, then the flag will also be cleared. + </entry> + </row> + <row> + <entry>V4L2_DV_FL_HALF_LINE</entry> + <entry>Specific to interlaced formats: if set, then field 1 (aka the odd field) +is really one half-line longer and field 2 (aka the even field) is really one half-line +shorter, so each field has exactly the same number of half-lines. Whether half-lines can be +detected or used depends on the hardware. + </entry> + </row> + </tbody> + </tgroup> + </table> </refsect1> <refsect1> &return-value; diff --git a/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml b/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml index b17a7aac6997..e3d5afcdafbb 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml @@ -265,6 +265,32 @@ These controls are described in <xref These controls are described in <xref linkend="flash-controls" />.</entry> </row> + <row> + <entry><constant>V4L2_CTRL_CLASS_JPEG</constant></entry> + <entry>0x9d0000</entry> + <entry>The class containing JPEG compression controls. +These controls are described in <xref + linkend="jpeg-controls" />.</entry> + </row> + <row> + <entry><constant>V4L2_CTRL_CLASS_IMAGE_SOURCE</constant></entry> + <entry>0x9e0000</entry> <entry>The class containing image + source controls. These controls are described in <xref + linkend="image-source-controls" />.</entry> + </row> + <row> + <entry><constant>V4L2_CTRL_CLASS_IMAGE_PROC</constant></entry> + <entry>0x9f0000</entry> <entry>The class containing image + processing controls. These controls are described in <xref + linkend="image-process-controls" />.</entry> + </row> + <row> + <entry><constant>V4L2_CTRL_CLASS_JPEG</constant></entry> + <entry>0x9d0000</entry> + <entry>The class containing JPEG compression controls. +These controls are described in <xref + linkend="jpeg-controls" />.</entry> + </row> </tbody> </tgroup> </table> diff --git a/Documentation/DocBook/media/v4l/vidioc-g-fmt.xml b/Documentation/DocBook/media/v4l/vidioc-g-fmt.xml index 17fbda15137b..52acff193a6f 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-fmt.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-fmt.xml @@ -116,7 +116,7 @@ this ioctl.</para> <colspec colname="c4" /> <tbody valign="top"> <row> - <entry>&v4l2-buf-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry></entry> <entry>Type of the data stream, see <xref diff --git a/Documentation/DocBook/media/v4l/vidioc-g-frequency.xml b/Documentation/DocBook/media/v4l/vidioc-g-frequency.xml index 66e9a5257861..69c178a4d205 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-frequency.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-frequency.xml @@ -95,14 +95,14 @@ the &v4l2-output; <structfield>modulator</structfield> field and the &v4l2-modulator; <structfield>index</structfield> field.</entry> </row> <row> - <entry>&v4l2-tuner-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry>The tuner type. This is the same value as in the -&v4l2-tuner; <structfield>type</structfield> field. The type must be set +&v4l2-tuner; <structfield>type</structfield> field. See The type must be set to <constant>V4L2_TUNER_RADIO</constant> for <filename>/dev/radioX</filename> device nodes, and to <constant>V4L2_TUNER_ANALOG_TV</constant> for all others. The field is not applicable to modulators, &ie; ignored -by drivers.</entry> +by drivers. See <xref linkend="v4l2-tuner-type" /></entry> </row> <row> <entry>__u32</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-g-parm.xml b/Documentation/DocBook/media/v4l/vidioc-g-parm.xml index 19b1d85dd668..f83d2cdd1185 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-parm.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-parm.xml @@ -75,11 +75,12 @@ devices.</para> &cs-ustr; <tbody valign="top"> <row> - <entry>&v4l2-buf-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry></entry> <entry>The buffer (stream) type, same as &v4l2-format; -<structfield>type</structfield>, set by the application.</entry> +<structfield>type</structfield>, set by the application. See <xref + linkend="v4l2-buf-type" /></entry> </row> <row> <entry>union</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-g-sliced-vbi-cap.xml b/Documentation/DocBook/media/v4l/vidioc-g-sliced-vbi-cap.xml index 71741daaf725..bd015d1563ff 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-sliced-vbi-cap.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-sliced-vbi-cap.xml @@ -148,7 +148,7 @@ using the &VIDIOC-S-FMT; ioctl as described in <xref <structfield>service_lines</structfield>[1][0] to zero.</entry> </row> <row> - <entry>&v4l2-buf-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry>Type of the data stream, see <xref linkend="v4l2-buf-type" />. Should be diff --git a/Documentation/DocBook/media/v4l/vidioc-g-tuner.xml b/Documentation/DocBook/media/v4l/vidioc-g-tuner.xml index 91ec2fb658f8..62a1aa200a36 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-tuner.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-tuner.xml @@ -107,7 +107,7 @@ user.<!-- FIXME Video inputs already have a name, the purpose of this field is not quite clear.--></para></entry> </row> <row> - <entry>&v4l2-tuner-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry spanname="hspan">Type of the tuner, see <xref linkend="v4l2-tuner-type" />.</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-prepare-buf.xml b/Documentation/DocBook/media/v4l/vidioc-prepare-buf.xml index 7bde698760e4..fa7ad7e33228 100644 --- a/Documentation/DocBook/media/v4l/vidioc-prepare-buf.xml +++ b/Documentation/DocBook/media/v4l/vidioc-prepare-buf.xml @@ -48,6 +48,12 @@ <refsect1> <title>Description</title> + <note> + <title>Experimental</title> + <para>This is an <link linkend="experimental"> experimental </link> + interface and may change in the future.</para> + </note> + <para>Applications can optionally call the <constant>VIDIOC_PREPARE_BUF</constant> ioctl to pass ownership of the buffer to the driver before actually enqueuing it, using the diff --git a/Documentation/DocBook/media/v4l/vidioc-query-dv-preset.xml b/Documentation/DocBook/media/v4l/vidioc-query-dv-preset.xml index 23b17f604211..1bc8aeb3ff1f 100644 --- a/Documentation/DocBook/media/v4l/vidioc-query-dv-preset.xml +++ b/Documentation/DocBook/media/v4l/vidioc-query-dv-preset.xml @@ -49,6 +49,10 @@ input</refpurpose> <refsect1> <title>Description</title> + <para>This ioctl is <emphasis role="bold">deprecated</emphasis>. + New drivers and applications should use &VIDIOC-QUERY-DV-TIMINGS; instead. + </para> + <para>The hardware may be able to detect the current DV preset automatically, similar to sensing the video standard. To do so, applications call <constant> VIDIOC_QUERY_DV_PRESET</constant> with a pointer to a diff --git a/Documentation/DocBook/media/v4l/vidioc-query-dv-timings.xml b/Documentation/DocBook/media/v4l/vidioc-query-dv-timings.xml new file mode 100644 index 000000000000..44935a0ffcf0 --- /dev/null +++ b/Documentation/DocBook/media/v4l/vidioc-query-dv-timings.xml @@ -0,0 +1,104 @@ +<refentry id="vidioc-query-dv-timings"> + <refmeta> + <refentrytitle>ioctl VIDIOC_QUERY_DV_TIMINGS</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>VIDIOC_QUERY_DV_TIMINGS</refname> + <refpurpose>Sense the DV preset received by the current +input</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>struct v4l2_dv_timings *<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>&fd;</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>VIDIOC_QUERY_DV_TIMINGS</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + + <note> + <title>Experimental</title> + <para>This is an <link linkend="experimental"> experimental </link> + interface and may change in the future.</para> + </note> + + <para>The hardware may be able to detect the current DV timings +automatically, similar to sensing the video standard. To do so, applications +call <constant>VIDIOC_QUERY_DV_TIMINGS</constant> with a pointer to a +&v4l2-dv-timings;. Once the hardware detects the timings, it will fill in the +timings structure. + +If the timings could not be detected because there was no signal, then +<errorcode>ENOLINK</errorcode> is returned. If a signal was detected, but +it was unstable and the receiver could not lock to the signal, then +<errorcode>ENOLCK</errorcode> is returned. If the receiver could lock to the signal, +but the format is unsupported (e.g. because the pixelclock is out of range +of the hardware capabilities), then the driver fills in whatever timings it +could find and returns <errorcode>ERANGE</errorcode>. In that case the application +can call &VIDIOC-DV-TIMINGS-CAP; to compare the found timings with the hardware's +capabilities in order to give more precise feedback to the user. +</para> + </refsect1> + + <refsect1> + &return-value; + + <variablelist> + <varlistentry> + <term><errorcode>ENOLINK</errorcode></term> + <listitem> + <para>No timings could be detected because no signal was found. +</para> + </listitem> + </varlistentry> + <varlistentry> + <term><errorcode>ENOLCK</errorcode></term> + <listitem> + <para>The signal was unstable and the hardware could not lock on to it. +</para> + </listitem> + </varlistentry> + <varlistentry> + <term><errorcode>ERANGE</errorcode></term> + <listitem> + <para>Timings were found, but they are out of range of the hardware +capabilities. +</para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> +</refentry> diff --git a/Documentation/DocBook/media/v4l/vidioc-queryctrl.xml b/Documentation/DocBook/media/v4l/vidioc-queryctrl.xml index 36660d311b51..e6645b996558 100644 --- a/Documentation/DocBook/media/v4l/vidioc-queryctrl.xml +++ b/Documentation/DocBook/media/v4l/vidioc-queryctrl.xml @@ -127,7 +127,7 @@ the first control with a higher ID. Drivers which do not support this flag yet always return an &EINVAL;.</entry> </row> <row> - <entry>&v4l2-ctrl-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry>Type of control, see <xref linkend="v4l2-ctrl-type" />.</entry> @@ -215,11 +215,12 @@ the array to zero.</entry> <table pgwide="1" frame="none" id="v4l2-querymenu"> <title>struct <structname>v4l2_querymenu</structname></title> - <tgroup cols="3"> + <tgroup cols="4"> &cs-str; <tbody valign="top"> <row> <entry>__u32</entry> + <entry></entry> <entry><structfield>id</structfield></entry> <entry>Identifies the control, set by the application from the respective &v4l2-queryctrl; @@ -227,18 +228,38 @@ from the respective &v4l2-queryctrl; </row> <row> <entry>__u32</entry> + <entry></entry> <entry><structfield>index</structfield></entry> <entry>Index of the menu item, starting at zero, set by the application.</entry> </row> <row> + <entry>union</entry> + <entry></entry> + <entry></entry> + <entry></entry> + </row> + <row> + <entry></entry> <entry>__u8</entry> <entry><structfield>name</structfield>[32]</entry> <entry>Name of the menu item, a NUL-terminated ASCII -string. This information is intended for the user.</entry> +string. This information is intended for the user. This field is valid +for <constant>V4L2_CTRL_FLAG_MENU</constant> type controls.</entry> + </row> + <row> + <entry></entry> + <entry>__s64</entry> + <entry><structfield>value</structfield></entry> + <entry> + Value of the integer menu item. This field is valid for + <constant>V4L2_CTRL_FLAG_INTEGER_MENU</constant> type + controls. + </entry> </row> <row> <entry>__u32</entry> + <entry></entry> <entry><structfield>reserved</structfield></entry> <entry>Reserved for future extensions. Drivers must set the array to zero.</entry> @@ -292,6 +313,20 @@ the menu items can be enumerated with the <constant>VIDIOC_QUERYMENU</constant> ioctl.</entry> </row> <row> + <entry><constant>V4L2_CTRL_TYPE_INTEGER_MENU</constant></entry> + <entry>≥ 0</entry> + <entry>1</entry> + <entry>N-1</entry> + <entry> + The control has a menu of N choices. The values of the + menu items can be enumerated with the + <constant>VIDIOC_QUERYMENU</constant> ioctl. This is + similar to <constant>V4L2_CTRL_TYPE_MENU</constant> + except that instead of strings, the menu items are + signed 64-bit integers. + </entry> + </row> + <row> <entry><constant>V4L2_CTRL_TYPE_BITMASK</constant></entry> <entry>0</entry> <entry>n/a</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-reqbufs.xml b/Documentation/DocBook/media/v4l/vidioc-reqbufs.xml index 7be4b1d29b90..d7c95057bc51 100644 --- a/Documentation/DocBook/media/v4l/vidioc-reqbufs.xml +++ b/Documentation/DocBook/media/v4l/vidioc-reqbufs.xml @@ -92,18 +92,19 @@ streamoff.--></para> <entry>The number of buffers requested or granted.</entry> </row> <row> - <entry>&v4l2-buf-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry>Type of the stream or buffers, this is the same as the &v4l2-format; <structfield>type</structfield> field. See <xref linkend="v4l2-buf-type" /> for valid values.</entry> </row> <row> - <entry>&v4l2-memory;</entry> + <entry>__u32</entry> <entry><structfield>memory</structfield></entry> <entry>Applications set this field to <constant>V4L2_MEMORY_MMAP</constant> or -<constant>V4L2_MEMORY_USERPTR</constant>.</entry> +<constant>V4L2_MEMORY_USERPTR</constant>. See <xref linkend="v4l2-memory" +/>.</entry> </row> <row> <entry>__u32</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-s-hw-freq-seek.xml b/Documentation/DocBook/media/v4l/vidioc-s-hw-freq-seek.xml index 18b1a8266f7c..407dfceb71f0 100644 --- a/Documentation/DocBook/media/v4l/vidioc-s-hw-freq-seek.xml +++ b/Documentation/DocBook/media/v4l/vidioc-s-hw-freq-seek.xml @@ -73,10 +73,11 @@ same value as in the &v4l2-input; <structfield>tuner</structfield> field and the &v4l2-tuner; <structfield>index</structfield> field.</entry> </row> <row> - <entry>&v4l2-tuner-type;</entry> + <entry>__u32</entry> <entry><structfield>type</structfield></entry> <entry>The tuner type. This is the same value as in the -&v4l2-tuner; <structfield>type</structfield> field.</entry> +&v4l2-tuner; <structfield>type</structfield> field. See <xref + linkend="v4l2-tuner-type" /></entry> </row> <row> <entry>__u32</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-subdev-g-crop.xml b/Documentation/DocBook/media/v4l/vidioc-subdev-g-crop.xml index 06197323a8cc..4cddd788c589 100644 --- a/Documentation/DocBook/media/v4l/vidioc-subdev-g-crop.xml +++ b/Documentation/DocBook/media/v4l/vidioc-subdev-g-crop.xml @@ -58,9 +58,12 @@ <title>Description</title> <note> - <title>Experimental</title> - <para>This is an <link linkend="experimental">experimental</link> - interface and may change in the future.</para> + <title>Obsolete</title> + + <para>This is an <link linkend="obsolete">obsolete</link> + interface and may be removed in the future. It is superseded by + <link linkend="vidioc-subdev-g-selection">the selection + API</link>.</para> </note> <para>To retrieve the current crop rectangle applications set the diff --git a/Documentation/DocBook/media/v4l/vidioc-subdev-g-selection.xml b/Documentation/DocBook/media/v4l/vidioc-subdev-g-selection.xml new file mode 100644 index 000000000000..208e9f0da3f3 --- /dev/null +++ b/Documentation/DocBook/media/v4l/vidioc-subdev-g-selection.xml @@ -0,0 +1,228 @@ +<refentry id="vidioc-subdev-g-selection"> + <refmeta> + <refentrytitle>ioctl VIDIOC_SUBDEV_G_SELECTION, VIDIOC_SUBDEV_S_SELECTION</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>VIDIOC_SUBDEV_G_SELECTION</refname> + <refname>VIDIOC_SUBDEV_S_SELECTION</refname> + <refpurpose>Get or set selection rectangles on a subdev pad</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>struct v4l2_subdev_selection *<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>&fd;</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>VIDIOC_SUBDEV_G_SELECTION, VIDIOC_SUBDEV_S_SELECTION</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + + <note> + <title>Experimental</title> + <para>This is an <link linkend="experimental">experimental</link> + interface and may change in the future.</para> + </note> + + <para>The selections are used to configure various image + processing functionality performed by the subdevs which affect the + image size. This currently includes cropping, scaling and + composition.</para> + + <para>The selection API replaces <link + linkend="vidioc-subdev-g-crop">the old subdev crop API</link>. All + the function of the crop API, and more, are supported by the + selections API.</para> + + <para>See <xref linkend="subdev"></xref> for + more information on how each selection target affects the image + processing pipeline inside the subdevice.</para> + + <section> + <title>Types of selection targets</title> + + <para>There are two types of selection targets: actual and bounds. + The ACTUAL targets are the targets which configure the hardware. + The BOUNDS target will return a rectangle that contain all + possible ACTUAL rectangles.</para> + </section> + + <section> + <title>Discovering supported features</title> + + <para>To discover which targets are supported, the user can + perform <constant>VIDIOC_SUBDEV_G_SELECTION</constant> on them. + Any unsupported target will return + <constant>EINVAL</constant>.</para> + </section> + + <table pgwide="1" frame="none" id="v4l2-subdev-selection-targets"> + <title>V4L2 subdev selection targets</title> + <tgroup cols="3"> + &cs-def; + <tbody valign="top"> + <row> + <entry><constant>V4L2_SUBDEV_SEL_TGT_CROP_ACTUAL</constant></entry> + <entry>0x0000</entry> + <entry>Actual crop. Defines the cropping + performed by the processing step.</entry> + </row> + <row> + <entry><constant>V4L2_SUBDEV_SEL_TGT_CROP_BOUNDS</constant></entry> + <entry>0x0002</entry> + <entry>Bounds of the crop rectangle.</entry> + </row> + <row> + <entry><constant>V4L2_SUBDEV_SEL_TGT_COMPOSE_ACTUAL</constant></entry> + <entry>0x0100</entry> + <entry>Actual compose rectangle. Used to configure scaling + on sink pads and composition on source pads.</entry> + </row> + <row> + <entry><constant>V4L2_SUBDEV_SEL_TGT_COMPOSE_BOUNDS</constant></entry> + <entry>0x0102</entry> + <entry>Bounds of the compose rectangle.</entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="v4l2-subdev-selection-flags"> + <title>V4L2 subdev selection flags</title> + <tgroup cols="3"> + &cs-def; + <tbody valign="top"> + <row> + <entry><constant>V4L2_SUBDEV_SEL_FLAG_SIZE_GE</constant></entry> + <entry>(1 << 0)</entry> <entry>Suggest the driver it + should choose greater or equal rectangle (in size) than + was requested. Albeit the driver may choose a lesser size, + it will only do so due to hardware limitations. Without + this flag (and + <constant>V4L2_SUBDEV_SEL_FLAG_SIZE_LE</constant>) the + behaviour is to choose the closest possible + rectangle.</entry> + </row> + <row> + <entry><constant>V4L2_SUBDEV_SEL_FLAG_SIZE_LE</constant></entry> + <entry>(1 << 1)</entry> <entry>Suggest the driver it + should choose lesser or equal rectangle (in size) than was + requested. Albeit the driver may choose a greater size, it + will only do so due to hardware limitations.</entry> + </row> + <row> + <entry><constant>V4L2_SUBDEV_SEL_FLAG_KEEP_CONFIG</constant></entry> + <entry>(1 << 2)</entry> + <entry>The configuration should not be propagated to any + further processing steps. If this flag is not given, the + configuration is propagated inside the subdevice to all + further processing steps.</entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="v4l2-subdev-selection"> + <title>struct <structname>v4l2_subdev_selection</structname></title> + <tgroup cols="3"> + &cs-str; + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>which</structfield></entry> + <entry>Active or try selection, from + &v4l2-subdev-format-whence;.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>pad</structfield></entry> + <entry>Pad number as reported by the media framework.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>target</structfield></entry> + <entry>Target selection rectangle. See + <xref linkend="v4l2-subdev-selection-targets">.</xref>.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>flags</structfield></entry> + <entry>Flags. See + <xref linkend="v4l2-subdev-selection-flags">.</xref></entry> + </row> + <row> + <entry>&v4l2-rect;</entry> + <entry><structfield>rect</structfield></entry> + <entry>Selection rectangle, in pixels.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[8]</entry> + <entry>Reserved for future extensions. Applications and drivers must + set the array to zero.</entry> + </row> + </tbody> + </tgroup> + </table> + + </refsect1> + + <refsect1> + &return-value; + + <variablelist> + <varlistentry> + <term><errorcode>EBUSY</errorcode></term> + <listitem> + <para>The selection rectangle can't be changed because the + pad is currently busy. This can be caused, for instance, by + an active video stream on the pad. The ioctl must not be + retried without performing another action to fix the problem + first. Only returned by + <constant>VIDIOC_SUBDEV_S_SELECTION</constant></para> + </listitem> + </varlistentry> + <varlistentry> + <term><errorcode>EINVAL</errorcode></term> + <listitem> + <para>The &v4l2-subdev-selection; + <structfield>pad</structfield> references a non-existing + pad, the <structfield>which</structfield> field references a + non-existing format, or the selection target is not + supported on the given subdev pad.</para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> +</refentry> diff --git a/Documentation/SubmittingPatches b/Documentation/SubmittingPatches index 4468ce24427c..c379a2a6949f 100644 --- a/Documentation/SubmittingPatches +++ b/Documentation/SubmittingPatches @@ -150,7 +150,8 @@ be able to justify all violations that remain in your patch. Look through the MAINTAINERS file and the source code, and determine if your change applies to a specific subsystem of the kernel, with -an assigned maintainer. If so, e-mail that person. +an assigned maintainer. If so, e-mail that person. The script +scripts/get_maintainer.pl can be very useful at this step. If no maintainer is listed, or the maintainer does not respond, send your patch to the primary Linux kernel developer's mailing list, diff --git a/Documentation/arm/SPEAr/overview.txt b/Documentation/arm/SPEAr/overview.txt index 28a9af953b9d..57aae7765c74 100644 --- a/Documentation/arm/SPEAr/overview.txt +++ b/Documentation/arm/SPEAr/overview.txt @@ -8,9 +8,8 @@ Introduction weblink : http://www.st.com/spear The ST Microelectronics SPEAr range of ARM9/CortexA9 System-on-Chip CPUs are - supported by the 'spear' platform of ARM Linux. Currently SPEAr300, - SPEAr310, SPEAr320 and SPEAr600 SOCs are supported. Support for the SPEAr13XX - series is in progress. + supported by the 'spear' platform of ARM Linux. Currently SPEAr1310, + SPEAr1340, SPEAr300, SPEAr310, SPEAr320 and SPEAr600 SOCs are supported. Hierarchy in SPEAr is as follows: @@ -26,33 +25,36 @@ Introduction - SPEAr600 (SOC) - SPEAr600 Evaluation Board - SPEAr13XX (13XX SOC series, based on ARM CORTEXA9) - - SPEAr1300 (SOC) + - SPEAr1310 (SOC) + - SPEAr1310 Evaluation Board + - SPEAr1340 (SOC) + - SPEAr1340 Evaluation Board Configuration ------------- A generic configuration is provided for each machine, and can be used as the default by - make spear600_defconfig - make spear300_defconfig - make spear310_defconfig - make spear320_defconfig + make spear13xx_defconfig + make spear3xx_defconfig + make spear6xx_defconfig Layout ------ - The common files for multiple machine families (SPEAr3XX, SPEAr6XX and - SPEAr13XX) are located in the platform code contained in arch/arm/plat-spear + The common files for multiple machine families (SPEAr3xx, SPEAr6xx and + SPEAr13xx) are located in the platform code contained in arch/arm/plat-spear with headers in plat/. Each machine series have a directory with name arch/arm/mach-spear followed by series name. Like mach-spear3xx, mach-spear6xx and mach-spear13xx. - Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c and for - spear6xx is mach-spear6xx/spear6xx.c. mach-spear* also contain soc/machine - specific files, like spear300.c, spear310.c, spear320.c and spear600.c. - mach-spear* doesn't contains board specific files as they fully support - Flattened Device Tree. + Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c, for + spear6xx is mach-spear6xx/spear6xx.c and for spear13xx family is + mach-spear13xx/spear13xx.c. mach-spear* also contain soc/machine specific + files, like spear1310.c, spear1340.c spear300.c, spear310.c, spear320.c and + spear600.c. mach-spear* doesn't contains board specific files as they fully + support Flattened Device Tree. Document Author diff --git a/Documentation/cgroups/memory.txt b/Documentation/cgroups/memory.txt index 9b1067afb224..dd88540bb995 100644 --- a/Documentation/cgroups/memory.txt +++ b/Documentation/cgroups/memory.txt @@ -184,12 +184,14 @@ behind this approach is that a cgroup that aggressively uses a shared page will eventually get charged for it (once it is uncharged from the cgroup that brought it in -- this will happen on memory pressure). +But see section 8.2: when moving a task to another cgroup, its pages may +be recharged to the new cgroup, if move_charge_at_immigrate has been chosen. + Exception: If CONFIG_CGROUP_CGROUP_MEM_RES_CTLR_SWAP is not used. When you do swapoff and make swapped-out pages of shmem(tmpfs) to be backed into memory in force, charges for pages are accounted against the caller of swapoff rather than the users of shmem. - 2.4 Swap Extension (CONFIG_CGROUP_MEM_RES_CTLR_SWAP) Swap Extension allows you to record charge for swap. A swapped-in page is @@ -374,14 +376,15 @@ cgroup might have some charge associated with it, even though all tasks have migrated away from it. (because we charge against pages, not against tasks.) -Such charges are freed or moved to their parent. At moving, both of RSS -and CACHES are moved to parent. -rmdir() may return -EBUSY if freeing/moving fails. See 5.1 also. +We move the stats to root (if use_hierarchy==0) or parent (if +use_hierarchy==1), and no change on the charge except uncharging +from the child. Charges recorded in swap information is not updated at removal of cgroup. Recorded information is discarded and a cgroup which uses swap (swapcache) will be charged as a new owner of it. +About use_hierarchy, see Section 6. 5. Misc. interfaces. @@ -394,13 +397,15 @@ will be charged as a new owner of it. Almost all pages tracked by this memory cgroup will be unmapped and freed. Some pages cannot be freed because they are locked or in-use. Such pages are - moved to parent and this cgroup will be empty. This may return -EBUSY if - VM is too busy to free/move all pages immediately. + moved to parent(if use_hierarchy==1) or root (if use_hierarchy==0) and this + cgroup will be empty. Typical use case of this interface is that calling this before rmdir(). Because rmdir() moves all pages to parent, some out-of-use page caches can be moved to the parent. If you want to avoid that, force_empty will be useful. + About use_hierarchy, see Section 6. + 5.2 stat file memory.stat file includes following statistics @@ -430,17 +435,10 @@ hierarchical_memory_limit - # of bytes of memory limit with regard to hierarchy hierarchical_memsw_limit - # of bytes of memory+swap limit with regard to hierarchy under which memory cgroup is. -total_cache - sum of all children's "cache" -total_rss - sum of all children's "rss" -total_mapped_file - sum of all children's "cache" -total_pgpgin - sum of all children's "pgpgin" -total_pgpgout - sum of all children's "pgpgout" -total_swap - sum of all children's "swap" -total_inactive_anon - sum of all children's "inactive_anon" -total_active_anon - sum of all children's "active_anon" -total_inactive_file - sum of all children's "inactive_file" -total_active_file - sum of all children's "active_file" -total_unevictable - sum of all children's "unevictable" +total_<counter> - # hierarchical version of <counter>, which in + addition to the cgroup's own value includes the + sum of all hierarchical children's values of + <counter>, i.e. total_cache # The following additional stats are dependent on CONFIG_DEBUG_VM. @@ -622,8 +620,7 @@ memory cgroup. bit | what type of charges would be moved ? -----+------------------------------------------------------------------------ 0 | A charge of an anonymous page(or swap of it) used by the target task. - | Those pages and swaps must be used only by the target task. You must - | enable Swap Extension(see 2.4) to enable move of swap charges. + | You must enable Swap Extension(see 2.4) to enable move of swap charges. -----+------------------------------------------------------------------------ 1 | A charge of file pages(normal file, tmpfs file(e.g. ipc shared memory) | and swaps of tmpfs file) mmapped by the target task. Unlike the case of @@ -636,8 +633,6 @@ memory cgroup. 8.3 TODO -- Implement madvise(2) to let users decide the vma to be moved or not to be - moved. - All of moving charge operations are done under cgroup_mutex. It's not good behavior to hold the mutex too long, so we may need some trick. diff --git a/Documentation/cgroups/resource_counter.txt b/Documentation/cgroups/resource_counter.txt index f3c4ec3626a2..0c4a344e78fa 100644 --- a/Documentation/cgroups/resource_counter.txt +++ b/Documentation/cgroups/resource_counter.txt @@ -92,6 +92,14 @@ to work with it. The _locked routines imply that the res_counter->lock is taken. + f. void res_counter_uncharge_until + (struct res_counter *rc, struct res_counter *top, + unsinged long val) + + Almost same as res_cunter_uncharge() but propagation of uncharge + stops when rc == top. This is useful when kill a res_coutner in + child cgroup. + 2.1 Other accounting routines There are more routines that may help you with common needs, like diff --git a/Documentation/cris/README b/Documentation/cris/README index d9b086869a60..8dbdb1a44429 100644 --- a/Documentation/cris/README +++ b/Documentation/cris/README @@ -1,38 +1,34 @@ -Linux 2.4 on the CRIS architecture -================================== -$Id: README,v 1.7 2001/04/19 12:38:32 bjornw Exp $ +Linux on the CRIS architecture +============================== -This is a port of Linux 2.4 to Axis Communications ETRAX 100LX embedded -network CPU. For more information about CRIS and ETRAX please see further -below. +This is a port of Linux to Axis Communications ETRAX 100LX, +ETRAX FS and ARTPEC-3 embedded network CPUs. + +For more information about CRIS and ETRAX please see further below. In order to compile this you need a version of gcc with support for the -ETRAX chip family. Please see this link for more information on how to +ETRAX chip family. Please see this link for more information on how to download the compiler and other tools useful when building and booting software for the ETRAX platform: -http://developer.axis.com/doc/software/devboard_lx/install-howto.html - -<more specific information should come in this document later> +http://developer.axis.com/wiki/doku.php?id=axis:install-howto-2_20 What is CRIS ? -------------- CRIS is an acronym for 'Code Reduced Instruction Set'. It is the CPU architecture in Axis Communication AB's range of embedded network CPU's, -called ETRAX. The latest CPU is called ETRAX 100LX, where LX stands for -'Linux' because the chip was designed to be a good host for the Linux -operating system. +called ETRAX. The ETRAX 100LX chip -------------------- -For reference, please see the press-release: +For reference, please see the following link: -http://www.axis.com/news/us/001101_etrax.htm +http://www.axis.com/products/dev_etrax_100lx/index.htm -The ETRAX 100LX is a 100 MIPS processor with 8kB cache, MMU, and a very broad -range of built-in interfaces, all with modern scatter/gather DMA. +The ETRAX 100LX is a 100 MIPS processor with 8kB cache, MMU, and a very broad +range of built-in interfaces, all with modern scatter/gather DMA. Memory interfaces: @@ -51,20 +47,28 @@ I/O interfaces: * SCSI * two parallel-ports * two generic 8-bit ports - - (not all interfaces are available at the same time due to chip pin + + (not all interfaces are available at the same time due to chip pin multiplexing) -The previous version of the ETRAX, the ETRAX 100, sits in almost all of -Axis shipping thin-servers like the Axis 2100 web camera or the ETRAX 100 -developer-board. It lacks an MMU so the Linux we run on that is a version -of uClinux (Linux 2.0 without MM-support) ported to the CRIS architecture. -The new Linux 2.4 port has full MM and needs a CPU with an MMU, so it will -not run on the ETRAX 100. +ETRAX 100LX is CRISv10 architecture. + + +The ETRAX FS and ARTPEC-3 chips +------------------------------- -A version of the Axis developer-board with ETRAX 100LX (running Linux -2.4) is now available. For more information please see developer.axis.com. +The ETRAX FS is a 200MHz 32-bit RISC processor with on-chip 16kB +I-cache and 16kB D-cache and with a wide range of device interfaces +including multiple high speed serial ports and an integrated USB 1.1 PHY. +The ARTPEC-3 is a variant of the ETRAX FS with additional IO-units +used by the Axis Communications network cameras. + +See below link for more information: + +http://www.axis.com/products/dev_etrax_fs/index.htm + +ETRAX FS and ARTPEC-3 are both CRISv32 architectures. Bootlog ------- @@ -182,10 +186,6 @@ SwapFree: 0 kB -rwxr-xr-x 1 342 100 16252 Jan 01 00:00 telnetd -(All programs are statically linked to the libc at this point - we have not ported the - shared libraries yet) - - diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index bfbc771a65f8..ac9e7516756e 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -1,6 +1,14 @@ Freescale i.MX Platforms Device Tree Bindings ----------------------------------------------- +i.MX23 Evaluation Kit +Required root node properties: + - compatible = "fsl,imx23-evk", "fsl,imx23"; + +i.MX28 Evaluation Kit +Required root node properties: + - compatible = "fsl,imx28-evk", "fsl,imx28"; + i.MX51 Babbage Board Required root node properties: - compatible = "fsl,imx51-babbage", "fsl,imx51"; @@ -29,6 +37,10 @@ i.MX6 Quad SABRE Lite Board Required root node properties: - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q"; +i.MX6 Quad SABRE Smart Device Board +Required root node properties: + - compatible = "fsl,imx6q-sabresd", "fsl,imx6q"; + Generic i.MX boards ------------------- diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index 9b4b82a721b6..62eb8df1e08d 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -11,7 +11,9 @@ have PPIs or SGIs. Main node required properties: - compatible : should be one of: + "arm,cortex-a15-gic" "arm,cortex-a9-gic" + "arm,cortex-a7-gic" "arm,arm11mp-gic" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an @@ -39,8 +41,9 @@ Main node required properties: the GIC cpu interface register base and size. Optional -- interrupts : Interrupt source of the parent interrupt controller. Only - present on secondary GICs. +- interrupts : Interrupt source of the parent interrupt controller on + secondary GICs, or VGIC maintainance interrupt on primary GIC (see + below). - cpu-offset : per-cpu offset within the distributor and cpu interface regions, used when the GIC doesn't have banked registers. The offset is @@ -57,3 +60,31 @@ Example: <0xfff10100 0x100>; }; + +* GIC virtualization extensions (VGIC) + +For ARM cores that support the virtualization extensions, additional +properties must be described (they only exist if the GIC is the +primary interrupt controller). + +Required properties: + +- reg : Additional regions specifying the base physical address and + size of the VGIC registers. The first additional region is the GIC + virtual interface control register base and size. The 2nd additional + region is the GIC virtual cpu interface register base and size. + +- interrupts : VGIC maintainance interrupt. + +Example: + + interrupt-controller@2c001000 { + compatible = "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x2c001000 0x1000>, + <0x2c002000 0x1000>, + <0x2c004000 0x2000>, + <0x2c006000 0x2000>; + interrupts = <1 9 0xf04>; + }; diff --git a/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt b/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt new file mode 100644 index 000000000000..f2f2171e530e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt @@ -0,0 +1,52 @@ +* Samsung Exynos Interrupt Combiner Controller + +Samsung's Exynos4 architecture includes a interrupt combiner controller which +can combine interrupt sources as a group and provide a single interrupt request +for the group. The interrupt request from each group are connected to a parent +interrupt controller, such as GIC in case of Exynos4210. + +The interrupt combiner controller consists of multiple combiners. Upto eight +interrupt sources can be connected to a combiner. The combiner outputs one +combined interrupt for its eight interrupt sources. The combined interrupt +is usually connected to a parent interrupt controller. + +A single node in the device tree is used to describe the interrupt combiner +controller module (which includes multiple combiners). A combiner in the +interrupt controller module shares config/control registers with other +combiners. For example, a 32-bit interrupt enable/disable config register +can accommodate upto 4 interrupt combiners (with each combiner supporting +upto 8 interrupt sources). + +Required properties: +- compatible: should be "samsung,exynos4210-combiner". +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt-cells: should be <2>. The meaning of the cells are + * First Cell: Combiner Group Number. + * Second Cell: Interrupt number within the group. +- reg: Base address and size of interrupt combiner registers. +- interrupts: The list of interrupts generated by the combiners which are then + connected to a parent interrupt controller. The format of the interrupt + specifier depends in the interrupt parent controller. + +Optional properties: +- samsung,combiner-nr: The number of interrupt combiners supported. If this + property is not specified, the default number of combiners is assumed + to be 16. +- interrupt-parent: pHandle of the parent interrupt controller, if not + inherited from the parent node. + + +Example: + + The following is a an example from the Exynos4210 SoC dtsi file. + + combiner:interrupt-controller@10440000 { + compatible = "samsung,exynos4210-combiner"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x10440000 0x1000>; + interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>, + <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>, + <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>, + <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>; + }; diff --git a/Documentation/devicetree/bindings/arm/spear-timer.txt b/Documentation/devicetree/bindings/arm/spear-timer.txt new file mode 100644 index 000000000000..c0017221cf55 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear-timer.txt @@ -0,0 +1,18 @@ +* SPEAr ARM Timer + +** Timer node required properties: + +- compatible : Should be: + "st,spear-timer" +- reg: Address range of the timer registers +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupt: Should contain the timer interrupt number + +Example: + + timer@f0000000 { + compatible = "st,spear-timer"; + reg = <0xf0000000 0x400>; + interrupts = <2>; + }; diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt index aa5f355cc947..0d42949df6c2 100644 --- a/Documentation/devicetree/bindings/arm/spear.txt +++ b/Documentation/devicetree/bindings/arm/spear.txt @@ -2,25 +2,25 @@ ST SPEAr Platforms Device Tree Bindings --------------------------------------- Boards with the ST SPEAr600 SoC shall have the following properties: - Required root node property: - compatible = "st,spear600"; Boards with the ST SPEAr300 SoC shall have the following properties: - Required root node property: - compatible = "st,spear300"; Boards with the ST SPEAr310 SoC shall have the following properties: - Required root node property: - compatible = "st,spear310"; Boards with the ST SPEAr320 SoC shall have the following properties: +Required root node property: +compatible = "st,spear320"; +Boards with the ST SPEAr1310 SoC shall have the following properties: Required root node property: +compatible = "st,spear1310"; -compatible = "st,spear320"; +Boards with the ST SPEAr1340 SoC shall have the following properties: +Required root node property: +compatible = "st,spear1340"; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt new file mode 100644 index 000000000000..234406d41c12 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt @@ -0,0 +1,11 @@ +NVIDIA Tegra AHB + +Required properties: +- compatible : "nvidia,tegra20-ahb" or "nvidia,tegra30-ahb" +- reg : Should contain 1 register ranges(address and length) + +Example: + ahb: ahb@6000c004 { + compatible = "nvidia,tegra20-ahb"; + reg = <0x6000c004 0x10c>; /* AHB Arbitration + Gizmo Controller */ + }; diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt new file mode 100644 index 000000000000..ded0398d3bdc --- /dev/null +++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt @@ -0,0 +1,19 @@ +* Freescale MXS DMA + +Required properties: +- compatible : Should be "fsl,<chip>-dma-apbh" or "fsl,<chip>-dma-apbx" +- reg : Should contain registers location and length + +Supported chips: +imx23, imx28. + +Examples: +dma-apbh@80004000 { + compatible = "fsl,imx28-dma-apbh"; + reg = <0x80004000 2000>; +}; + +dma-apbx@80024000 { + compatible = "fsl,imx28-dma-apbx"; + reg = <0x80024000 2000>; +}; diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt new file mode 100644 index 000000000000..c0d85dbcada5 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -0,0 +1,17 @@ +* Synopsys Designware DMA Controller + +Required properties: +- compatible: "snps,dma-spear1340" +- reg: Address range of the DMAC registers +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupt: Should contain the DMAC interrupt number + +Example: + + dma@fc000000 { + compatible = "snps,dma-spear1340"; + reg = <0xfc000000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <12>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt new file mode 100644 index 000000000000..f93d51478d5a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt @@ -0,0 +1,38 @@ +Lantiq SoC External Bus memory mapped GPIO controller + +By attaching hardware latches to the EBU it is possible to create output +only gpios. This driver configures a special memory address, which when +written to outputs 16 bit to the latches. + +The node describing the memory mapped GPIOs needs to be a child of the node +describing the "lantiq,localbus". + +Required properties: +- compatible : Should be "lantiq,gpio-mm-lantiq" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller : Marks the device node as a gpio controller. + +Optional properties: +- lantiq,shadow : The default value that we shall assume as already set on the + shift register cascade. + +Example: + +localbus@0 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ + 1 0 0x4000000 0x4000010>; /* addsel1 */ + compatible = "lantiq,localbus", "simple-bus"; + + gpio_mm0: gpio@4000000 { + compatible = "lantiq,gpio-mm"; + reg = <1 0x0 0x10>; + gpio-controller; + #gpio-cells = <2>; + lantiq,shadow = <0x77f> + }; +} diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt new file mode 100644 index 000000000000..0c35673f7a3e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt @@ -0,0 +1,87 @@ +* Freescale MXS GPIO controller + +The Freescale MXS GPIO controller is part of MXS PIN controller. The +GPIOs are organized in port/bank. Each port consists of 32 GPIOs. + +As the GPIO controller is embedded in the PIN controller and all the +GPIO ports share the same IO space with PIN controller, the GPIO node +will be represented as sub-nodes of MXS pinctrl node. + +Required properties for GPIO node: +- compatible : Should be "fsl,<soc>-gpio". The supported SoCs include + imx23 and imx28. +- interrupts : Should be the port interrupt shared by all 32 pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +Note: Each GPIO port should have an alias correctly numbered in "aliases" +node. + +Examples: + +aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + gpio4 = &gpio4; +}; + +pinctrl@80018000 { + compatible = "fsl,imx28-pinctrl", "simple-bus"; + reg = <0x80018000 2000>; + + gpio0: gpio@0 { + compatible = "fsl,imx28-gpio"; + interrupts = <127>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@1 { + compatible = "fsl,imx28-gpio"; + interrupts = <126>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@2 { + compatible = "fsl,imx28-gpio"; + interrupts = <125>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@3 { + compatible = "fsl,imx28-gpio"; + interrupts = <124>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio@4 { + compatible = "fsl,imx28-gpio"; + interrupts = <123>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt new file mode 100644 index 000000000000..854de130a971 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt @@ -0,0 +1,42 @@ +Lantiq SoC Serial To Parallel (STP) GPIO controller + +The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a +peripheral controller used to drive external shift register cascades. At most +3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem +to drive the 2 LSBs of the cascade automatically. + + +Required properties: +- compatible : Should be "lantiq,gpio-stp-xway" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller : Marks the device node as a gpio controller. + +Optional properties: +- lantiq,shadow : The default value that we shall assume as already set on the + shift register cascade. +- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled + in the shift register cascade. +- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit + property can enable this feature. +- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade. +- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade. +- lantiq,rising : use rising instead of falling edge for the shift register + +Example: + +gpio1: stp@E100BB0 { + compatible = "lantiq,gpio-stp-xway"; + reg = <0xE100BB0 0x40>; + #gpio-cells = <2>; + gpio-controller; + + lantiq,shadow = <0xffff>; + lantiq,groups = <0x7>; + lantiq,dsl = <0x3>; + lantiq,phy1 = <0x7>; + lantiq,phy2 = <0x7>; + /* lantiq,rising; */ +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt new file mode 100644 index 000000000000..49819367a011 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt @@ -0,0 +1,43 @@ +NXP LPC32xx SoC GPIO controller + +Required properties: +- compatible: must be "nxp,lpc3220-gpio" +- reg: Physical base address and length of the controller's registers. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be 3: + 1) bank: + 0: GPIO P0 + 1: GPIO P1 + 2: GPIO P2 + 3: GPIO P3 + 4: GPI P3 + 5: GPO P3 + 2) pin number + 3) optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- reg: Index of the GPIO group + +Example: + + gpio: gpio@40028000 { + compatible = "nxp,lpc3220-gpio"; + reg = <0x40028000 0x1000>; + gpio-controller; + #gpio-cells = <3>; /* bank, pin, flags */ + }; + + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpio 5 1 1>; /* GPO_P3 1, active low */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + gpios = <&gpio 5 14 1>; /* GPO_P3 14, active low */ + linux,default-trigger = "timer"; + default-state = "off"; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt new file mode 100644 index 000000000000..1bfc02de1b0c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt @@ -0,0 +1,16 @@ +* Freescale MXS Inter IC (I2C) Controller + +Required properties: +- compatible: Should be "fsl,<chip>-i2c" +- reg: Should contain registers location and length +- interrupts: Should contain ERROR and DMA interrupts + +Examples: + +i2c0: i2c@80058000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-i2c"; + reg = <0x80058000 2000>; + interrupts = <111 68>; +}; diff --git a/Documentation/devicetree/bindings/i2c/mux.txt b/Documentation/devicetree/bindings/i2c/mux.txt new file mode 100644 index 000000000000..af84cce5cd7b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/mux.txt @@ -0,0 +1,60 @@ +Common i2c bus multiplexer/switch properties. + +An i2c bus multiplexer/switch will have several child busses that are +numbered uniquely in a device dependent manner. The nodes for an i2c bus +multiplexer/switch will have one child node for each child +bus. + +Required properties: +- #address-cells = <1>; +- #size-cells = <0>; + +Required properties for child nodes: +- #address-cells = <1>; +- #size-cells = <0>; +- reg : The sub-bus number. + +Optional properties for child nodes: +- Other properties specific to the multiplexer/switch hardware. +- Child nodes conforming to i2c bus binding + + +Example : + + /* + An NXP pca9548 8 channel I2C multiplexer at address 0x70 + with two NXP pca8574 GPIO expanders attached, one each to + ports 3 and 4. + */ + + mux@70 { + compatible = "nxp,pca9548"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + gpio1: gpio@38 { + compatible = "nxp,pca8574"; + reg = <0x38>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + gpio2: gpio@38 { + compatible = "nxp,pca8574"; + reg = <0x38>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt index 38832c712919..b6cb5a12c672 100644 --- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt @@ -6,14 +6,18 @@ Required properties: - compatible: value should be either of the following. (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c. (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. + (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used + inside HDMIPHY block found on several samsung SoCs - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. - - gpios: The order of the gpios should be the following: <SDA, SCL>. - The gpio specifier depends on the gpio controller. Optional properties: + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. Required in all + cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output + lines are permanently wired to the respective client - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not diff --git a/Documentation/devicetree/bindings/i2c/xiic.txt b/Documentation/devicetree/bindings/i2c/xiic.txt new file mode 100644 index 000000000000..ceabbe91ae44 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/xiic.txt @@ -0,0 +1,22 @@ +Xilinx IIC controller: + +Required properties: +- compatible : Must be "xlnx,xps-iic-2.00.a" +- reg : IIC register location and length +- interrupts : IIC controller unterrupt +- #address-cells = <1> +- #size-cells = <0> + +Optional properties: +- Child nodes conforming to i2c bus binding + +Example: + + axi_iic_0: i2c@40800000 { + compatible = "xlnx,xps-iic-2.00.a"; + interrupts = < 1 2 >; + reg = < 0x40800000 0x10000 >; + + #size-cells = <0>; + #address-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/input/spear-keyboard.txt b/Documentation/devicetree/bindings/input/spear-keyboard.txt new file mode 100644 index 000000000000..4a846d26da23 --- /dev/null +++ b/Documentation/devicetree/bindings/input/spear-keyboard.txt @@ -0,0 +1,20 @@ +* SPEAr keyboard controller + +Required properties: +- compatible: "st,spear300-kbd" + +Optional properties, in addition to those specified by the shared +matrix-keyboard bindings: +- autorepeat: bool: enables key autorepeat +- st,mode: keyboard mode: 0 - 9x9, 1 - 6x6, 2 - 2x2 + +Example: + +kbd@fc400000 { + compatible = "st,spear300-kbd"; + reg = <0xfc400000 0x100>; + linux,keymap = < 0x00030012 + 0x0102003a >; + autorepeat; + st,mode = <0>; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt new file mode 100644 index 000000000000..41cbf4b7a670 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt @@ -0,0 +1,16 @@ +* NXP LPC32xx SoC Touchscreen Controller (TSC) + +Required properties: +- compatible: must be "nxp,lpc3220-tsc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The TSC/ADC interrupt + +Example: + + tsc@40048000 { + compatible = "nxp,lpc3220-tsc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <39 0>; + }; diff --git a/Documentation/devicetree/bindings/input/twl6040-vibra.txt b/Documentation/devicetree/bindings/input/twl6040-vibra.txt new file mode 100644 index 000000000000..5b1918b818fb --- /dev/null +++ b/Documentation/devicetree/bindings/input/twl6040-vibra.txt @@ -0,0 +1,37 @@ +Vibra driver for the twl6040 family + +The vibra driver is a child of the twl6040 MFD dirver. +Documentation/devicetree/bindings/mfd/twl6040.txt + +Required properties: +- compatible : Must be "ti,twl6040-vibra"; +- interrupts: 4, Vibra overcurrent interrupt +- vddvibl-supply: Regulator supplying the left vibra motor +- vddvibr-supply: Regulator supplying the right vibra motor +- vibldrv_res: Board specific left driver resistance +- vibrdrv_res: Board specific right driver resistance +- viblmotor_res: Board specific left motor resistance +- vibrmotor_res: Board specific right motor resistance + +Optional properties: +- vddvibl_uV: If the vddvibl default voltage need to be changed +- vddvibr_uV: If the vddvibr default voltage need to be changed + +Example: +/* + * 8-channel high quality low-power audio codec + * http://www.ti.com/lit/ds/symlink/twl6040.pdf + */ +twl6040: twl6040@4b { + ... + twl6040_vibra: twl6040@1 { + compatible = "ti,twl6040-vibra"; + interrupts = <4>; + vddvibl-supply = <&vbat>; + vddvibr-supply = <&vbat>; + vibldrv_res = <8>; + vibrdrv_res = <3>; + viblmotor_res = <10>; + vibrmotor_res = <10>; + }; +}; diff --git a/Documentation/devicetree/bindings/iommu/nvidia,tegra20-gart.txt b/Documentation/devicetree/bindings/iommu/nvidia,tegra20-gart.txt new file mode 100644 index 000000000000..099d9362ebc1 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/nvidia,tegra20-gart.txt @@ -0,0 +1,14 @@ +NVIDIA Tegra 20 GART + +Required properties: +- compatible: "nvidia,tegra20-gart" +- reg: Two pairs of cells specifying the physical address and size of + the memory controller registers and the GART aperture respectively. + +Example: + + gart { + compatible = "nvidia,tegra20-gart"; + reg = <0x7000f024 0x00000018 /* controller registers */ + 0x58000000 0x02000000>; /* GART aperture */ + }; diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt new file mode 100644 index 000000000000..1857f4a6b9a9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -0,0 +1,60 @@ +* Dialog DA9052/53 Power Management Integrated Circuit (PMIC) + +Required properties: +- compatible : Should be "dlg,da9052", "dlg,da9053-aa", + "dlg,da9053-ab", or "dlg,da9053-bb" + +Sub-nodes: +- regulators : Contain the regulator nodes. The DA9052/53 regulators are + bound using their names as listed below: + + buck0 : regulator BUCK0 + buck1 : regulator BUCK1 + buck2 : regulator BUCK2 + buck3 : regulator BUCK3 + ldo4 : regulator LDO4 + ldo5 : regulator LDO5 + ldo6 : regulator LDO6 + ldo7 : regulator LDO7 + ldo8 : regulator LDO8 + ldo9 : regulator LDO9 + ldo10 : regulator LDO10 + ldo11 : regulator LDO11 + ldo12 : regulator LDO12 + ldo13 : regulator LDO13 + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Examples: + +i2c@63fc8000 { /* I2C1 */ + status = "okay"; + + pmic: dialog@48 { + compatible = "dlg,da9053-aa"; + reg = <0x48>; + + regulators { + buck0 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2075000>; + }; + + buck1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2075000>; + }; + + buck2 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <2500000>; + }; + + buck3 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <2500000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt new file mode 100644 index 000000000000..645f5eaadb3f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -0,0 +1,133 @@ +TPS65910 Power Management Integrated Circuit + +Required properties: +- compatible: "ti,tps65910" or "ti,tps65911" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- #gpio-cells: number of cells to describe a GPIO, this should be 2. + The first cell is the GPIO number. + The second cell is used to specify additional options <unused>. +- gpio-controller: mark the device as a GPIO controller +- #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1, + vaux2, vaux33, vmmc + tps65911: vrtc, vio, vdd1, vdd3, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5, + ldo6, ldo7, ldo8 + +Optional properties: +- ti,vmbch-threshold: (tps65911) main battery charged threshold + comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,vmbch2-threshold: (tps65911) main battery discharged threshold + comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,en-gpio-sleep: enable sleep control for gpios + There should be 9 entries here, one for each gpio. + +Regulator Optional properties: +- ti,regulator-ext-sleep-control: enable external sleep + control through external inputs [0 (not enabled), 1 (EN1), 2 (EN2) or 4(EN3)] + If this property is not defined, it defaults to 0 (not enabled). + +Example: + + pmu: tps65910@d2 { + compatible = "ti,tps65910"; + reg = <0xd2>; + interrupt-parent = <&intc>; + interrupts = < 0 118 0x04 >; + + #gpio-cells = <2>; + gpio-controller; + + #interrupt-cells = <2>; + interrupt-controller; + + ti,vmbch-threshold = 0; + ti,vmbch2-threshold = 0; + + ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; + + regulators { + vdd1_reg: vdd1 { + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <0>; + }; + vdd2_reg: vdd2 { + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <4>; + }; + vddctrl_reg: vddctrl { + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <0>; + }; + vio_reg: vio { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <1>; + }; + ldo1_reg: ldo1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo2_reg: ldo2 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo3_reg: ldo3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo4_reg: ldo4 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + ti,regulator-ext-sleep-control = <0>; + }; + ldo5_reg: ldo5 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo6_reg: ldo6 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo7_reg: ldo7 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <1>; + }; + ldo8_reg: ldo8 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + ti,regulator-ext-sleep-control = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt new file mode 100644 index 000000000000..bc67c6f424aa --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -0,0 +1,62 @@ +Texas Instruments TWL6040 family + +The TWL6040s are 8-channel high quality low-power audio codecs providing audio +and vibra functionality on OMAP4+ platforms. +They are connected ot the host processor via i2c for commands, McPDM for audio +data and commands. + +Required properties: +- compatible : Must be "ti,twl6040"; +- reg: must be 0x4b for i2c address +- interrupts: twl6040 has one interrupt line connecteded to the main SoC +- interrupt-parent: The parent interrupt controller +- twl6040,audpwron-gpio: Power on GPIO line for the twl6040 + +- vio-supply: Regulator for the twl6040 VIO supply +- v2v1-supply: Regulator for the twl6040 V2V1 supply + +Optional properties, nodes: +- enable-active-high: To power on the twl6040 during boot. + +Vibra functionality +Required properties: +- vddvibl-supply: Regulator for the left vibra motor +- vddvibr-supply: Regulator for the right vibra motor +- vibra { }: Configuration section for vibra parameters containing the following + properties: +- ti,vibldrv-res: Resistance parameter for left driver +- ti,vibrdrv-res: Resistance parameter for right driver +- ti,viblmotor-res: Resistance parameter for left motor +- ti,viblmotor-res: Resistance parameter for right motor + +Optional properties within vibra { } section: +- vddvibl_uV: If the vddvibl default voltage need to be changed +- vddvibr_uV: If the vddvibr default voltage need to be changed + +Example: +&i2c1 { + twl6040: twl@4b { + compatible = "ti,twl6040"; + reg = <0x4b>; + + interrupts = <0 119 4>; + interrupt-parent = <&gic>; + twl6040,audpwron-gpio = <&gpio4 31 0>; + + vio-supply = <&v1v8>; + v2v1-supply = <&v2v1>; + enable-active-high; + + /* regulators for vibra motor */ + vddvibl-supply = <&vbat>; + vddvibr-supply = <&vbat>; + + vibra { + /* Vibra driver, motor resistance parameters */ + ti,vibldrv-res = <8>; + ti,vibrdrv-res = <3>; + ti,viblmotor-res = <10>; + ti,vibrmotor-res = <10>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index 64bcb8be973c..0d93b4b0e0e3 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -11,9 +11,11 @@ Required properties: - interrupt-parent : interrupt source phandle. - clock-frequency : specifies eSDHC base clock frequency. - sdhci,wp-inverted : (optional) specifies that eSDHC controller - reports inverted write-protect state; + reports inverted write-protect state; New devices should use + the generic "wp-inverted" property. - sdhci,1-bit-only : (optional) specifies that a controller can - only handle 1-bit data transfers. + only handle 1-bit data transfers. New devices should use the + generic "bus-width = <1>" property. - sdhci,auto-cmd12: (optional) specifies that a controller can only handle auto CMD12. diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index ab22fe6e73ab..c7e404b3ef05 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -9,7 +9,7 @@ Required properties: - interrupts : Should contain eSDHC interrupt Optional properties: -- fsl,card-wired : Indicate the card is wired to host permanently +- non-removable : Indicate the card is wired to host permanently - fsl,cd-internal : Indicate to use controller internal card detection - fsl,wp-internal : Indicate to use controller internal write protection - cd-gpios : Specify GPIOs for card detection diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt index 89a0084df2f7..d64aea5a4203 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt @@ -10,7 +10,8 @@ Required properties: Optional properties: - gpios : may specify GPIOs in this order: Card-Detect GPIO, - Write-Protect GPIO. + Write-Protect GPIO. Note that this does not follow the + binding from mmc.txt, for historic reasons. - interrupts : the interrupt of a card detect interrupt. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt new file mode 100644 index 000000000000..6e70dcde0a71 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -0,0 +1,27 @@ +These properties are common to multiple MMC host controllers. Any host +that requires the respective functionality should implement them using +these definitions. + +Required properties: +- bus-width: Number of data lines, can be <1>, <4>, or <8> + +Optional properties: +- cd-gpios : Specify GPIOs for card detection, see gpio binding +- wp-gpios : Specify GPIOs for write protection, see gpio binding +- cd-inverted: when present, polarity on the wp gpio line is inverted +- wp-inverted: when present, polarity on the wp gpio line is inverted +- non-removable: non-removable slot (like eMMC) +- max-frequency: maximum operating clock frequency + +Example: + +sdhci@ab000000 { + compatible = "sdhci"; + reg = <0xab000000 0x200>; + interrupts = <23>; + bus-width = <4>; + cd-gpios = <&gpio 69 0>; + cd-inverted; + wp-gpios = <&gpio 70 0>; + max-frequency = <50000000>; +} diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt new file mode 100644 index 000000000000..14a81d526118 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -0,0 +1,19 @@ +* ARM PrimeCell MultiMedia Card Interface (MMCI) PL180/1 + +The ARM PrimeCell MMCI PL180 and PL181 provides and interface for +reading and writing to MultiMedia and SD cards alike. + +Required properties: +- compatible : contains "arm,pl18x", "arm,primecell". +- reg : contains pl18x registers and length. +- interrupts : contains the device IRQ(s). +- arm,primecell-periphid : contains the PrimeCell Peripheral ID. + +Optional properties: +- wp-gpios : contains any write protect (ro) gpios +- cd-gpios : contains any card detection gpios +- cd-inverted : indicates whether the cd gpio is inverted +- max-frequency : contains the maximum operating frequency +- bus-width : number of data lines, can be <1>, <4>, or <8> +- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable +- mmc-cap-sd-highspeed : indicates whether SD is high speed capable diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt new file mode 100644 index 000000000000..14d870a9e3db --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt @@ -0,0 +1,25 @@ +* Freescale MXS MMC controller + +The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller +to support MMC, SD, and SDIO types of memory cards. + +Required properties: +- compatible: Should be "fsl,<chip>-mmc". The supported chips include + imx23 and imx28. +- reg: Should contain registers location and length +- interrupts: Should contain ERROR and DMA interrupts +- fsl,ssp-dma-channel: APBH DMA channel for the SSP +- bus-width: Number of data lines, can be <1>, <4>, or <8> + +Optional properties: +- wp-gpios: Specify GPIOs for write protection + +Examples: + +ssp0: ssp@80010000 { + compatible = "fsl,imx28-mmc"; + reg = <0x80010000 2000>; + interrupts = <96 82>; + fsl,ssp-dma-channel = <0>; + bus-width = <8>; +}; diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt index 7e51154679a6..f77c3031607f 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt @@ -7,12 +7,12 @@ Required properties: - compatible : Should be "nvidia,<chip>-sdhci" - reg : Should contain SD/MMC registers location and length - interrupts : Should contain SD/MMC interrupt +- bus-width : Number of data lines, can be <1>, <4>, or <8> Optional properties: - cd-gpios : Specify GPIOs for card detection - wp-gpios : Specify GPIOs for write protection - power-gpios : Specify GPIOs for power control -- support-8bit : Boolean, indicates if 8-bit mode should be used. Example: @@ -23,5 +23,5 @@ sdhci@c8000200 { cd-gpios = <&gpio 69 0>; /* gpio PI5 */ wp-gpios = <&gpio 57 0>; /* gpio PH1 */ power-gpios = <&gpio 155 0>; /* gpio PT3 */ - support-8bit; + bus-width = <8>; }; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index dbd4368ab8cc..8a53958c9a9f 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -15,7 +15,7 @@ Optional properties: ti,dual-volt: boolean, supports dual voltage cards <supply-name>-supply: phandle to the regulator device tree node "supply-name" examples are "vmmc", "vmmc_aux" etc -ti,bus-width: Number of data lines, default assumed is 1 if the property is missing. +bus-width: Number of data lines, default assumed is 1 if the property is missing. cd-gpios: GPIOs for card detection wp-gpios: GPIOs for write protection ti,non-removable: non-removable slot (like eMMC) @@ -27,7 +27,7 @@ Example: reg = <0x4809c000 0x400>; ti,hwmods = "mmc1"; ti,dual-volt; - ti,bus-width = <4>; + bus-width = <4>; vmmc-supply = <&vmmc>; /* phandle to regulator node */ ti,non-removable; }; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index de439517dff0..7ab9e1a2d8be 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -14,7 +14,7 @@ Optional properties: Example: -fec@83fec000 { +ethernet@83fec000 { compatible = "fsl,imx51-fec", "fsl,imx27-fec"; reg = <0x83fec000 0x4000>; interrupts = <87>; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt index 3664d37e6799..b4480d5c3aca 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt @@ -4,6 +4,8 @@ Required properties: - compatible : "st,spear300-pinmux" : "st,spear310-pinmux" : "st,spear320-pinmux" + : "st,spear1310-pinmux" + : "st,spear1340-pinmux" - reg : Address range of the pinctrl registers - st,pinmux-mode: Mandatory for SPEAr300 and SPEAr320 and invalid for others. - Its values for SPEAr300: @@ -89,6 +91,37 @@ For SPEAr320 machines: "rmii0_1_grp", "i2c1_8_9_grp", "i2c1_98_99_grp", "i2c2_0_1_grp", "i2c2_2_3_grp", "i2c2_19_20_grp", "i2c2_75_76_grp", "i2c2_96_97_grp" +For SPEAr1310 machines: + "i2c0_grp", "ssp0_grp", "ssp0_cs0_grp", "ssp0_cs1_2_grp", "i2s0_grp", + "i2s1_grp", "clcd_grp", "clcd_high_res_grp", "arm_gpio_grp", + "smi_2_chips_grp", "smi_4_chips_grp", "gmii_grp", "rgmii_grp", + "smii_0_1_2_grp", "ras_mii_txclk_grp", "nand_8bit_grp", + "nand_16bit_grp", "nand_4_chips_grp", "keyboard_6x6_grp", + "keyboard_rowcol6_8_grp", "uart0_grp", "uart0_modem_grp", + "gpt0_tmr0_grp", "gpt0_tmr1_grp", "gpt1_tmr0_grp", "gpt1_tmr1_grp", + "sdhci_grp", "cf_grp", "xd_grp", "touch_xy_grp", + "uart1_disable_i2c_grp", "uart1_disable_sd_grp", "uart2_3_grp", + "uart4_grp", "uart5_grp", "rs485_0_1_tdm_0_1_grp", "i2c_1_2_grp", + "i2c3_dis_smi_clcd_grp", "i2c3_dis_sd_i2s0_grp", "i2c_4_5_dis_smi_grp", + "i2c4_dis_sd_grp", "i2c5_dis_sd_grp", "i2c_6_7_dis_kbd_grp", + "i2c6_dis_sd_grp", "i2c7_dis_sd_grp", "can0_dis_nor_grp", + "can0_dis_sd_grp", "can1_dis_sd_grp", "can1_dis_kbd_grp", "pcie0_grp", + "pcie1_grp", "pcie2_grp", "sata0_grp", "sata1_grp", "sata2_grp", + "ssp1_dis_kbd_grp", "ssp1_dis_sd_grp", "gpt64_grp" + +For SPEAr1340 machines: + "pads_as_gpio_grp", "fsmc_8bit_grp", "fsmc_16bit_grp", "fsmc_pnor_grp", + "keyboard_row_col_grp", "keyboard_col5_grp", "spdif_in_grp", + "spdif_out_grp", "gpt_0_1_grp", "pwm0_grp", "pwm1_grp", "pwm2_grp", + "pwm3_grp", "vip_mux_grp", "vip_mux_cam0_grp", "vip_mux_cam1_grp", + "vip_mux_cam2_grp", "vip_mux_cam3_grp", "cam0_grp", "cam1_grp", + "cam2_grp", "cam3_grp", "smi_grp", "ssp0_grp", "ssp0_cs1_grp", + "ssp0_cs2_grp", "ssp0_cs3_grp", "uart0_grp", "uart0_enh_grp", + "uart1_grp", "i2s_in_grp", "i2s_out_grp", "gmii_grp", "rgmii_grp", + "rmii_grp", "sgmii_grp", "i2c0_grp", "i2c1_grp", "cec0_grp", "cec1_grp", + "sdhci_grp", "cf_grp", "xd_grp", "clcd_grp", "arm_trace_grp", + "miphy_dbg_grp", "pcie_grp", "sata_grp" + Valid values for function names are: For All SPEAr3xx machines: "firda", "i2c0", "ssp_cs", "ssp0", "mii0", "gpio0", "uart0_ext", @@ -106,3 +139,17 @@ For SPEAr320 machines: "uart2", "uart3", "uart4", "uart5", "uart6", "rs485", "touchscreen", "can0", "can1", "pwm0_1", "pwm2", "pwm3", "ssp1", "ssp2", "mii2", "mii0_1", "i2c1", "i2c2" + + +For SPEAr1310 machines: + "i2c0", "ssp0", "i2s0", "i2s1", "clcd", "arm_gpio", "smi", "gmii", + "rgmii", "smii_0_1_2", "ras_mii_txclk", "nand", "keyboard", "uart0", + "gpt0", "gpt1", "sdhci", "cf", "xd", "touchscreen", "uart1", "uart2_3", + "uart4", "uart5", "rs485_0_1_tdm_0_1", "i2c_1_2", "i2c3_i2s1", + "i2c_4_5", "i2c_6_7", "can0", "can1", "pci", "sata", "ssp1", "gpt64" + +For SPEAr1340 machines: + "pads_as_gpio", "fsmc", "keyboard", "spdif_in", "spdif_out", "gpt_0_1", + "pwm", "vip", "cam0", "cam1", "cam2", "cam3", "smi", "ssp0", "uart0", + "uart1", "i2s", "gmac", "i2c0", "i2c1", "cec0", "cec1", "sdhci", "cf", + "xd", "clcd", "arm_trace", "miphy_dbg", "pcie", "sata" diff --git a/Documentation/devicetree/bindings/rtc/lpc32xx-rtc.txt b/Documentation/devicetree/bindings/rtc/lpc32xx-rtc.txt new file mode 100644 index 000000000000..a87a1e9bc060 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/lpc32xx-rtc.txt @@ -0,0 +1,15 @@ +* NXP LPC32xx SoC Real Time Clock controller + +Required properties: +- compatible: must be "nxp,lpc3220-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The RTC interrupt + +Example: + + rtc@40024000 { + compatible = "nxp,lpc3220-rtc"; + reg = <0x40024000 0x1000>; + interrupts = <52 0>; + }; diff --git a/Documentation/devicetree/bindings/rtc/spear-rtc.txt b/Documentation/devicetree/bindings/rtc/spear-rtc.txt new file mode 100644 index 000000000000..ca67ac62108e --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/spear-rtc.txt @@ -0,0 +1,17 @@ +* SPEAr RTC + +Required properties: +- compatible : "st,spear600-rtc" +- reg : Address range of the rtc registers +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupt: Should contain the rtc interrupt number + +Example: + + rtc@fc000000 { + compatible = "st,spear600-rtc"; + reg = <0xfc000000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <12>; + }; diff --git a/Documentation/devicetree/bindings/sound/omap-dmic.txt b/Documentation/devicetree/bindings/sound/omap-dmic.txt new file mode 100644 index 000000000000..fd8105f18978 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/omap-dmic.txt @@ -0,0 +1,21 @@ +* Texas Instruments OMAP4+ Digital Microphone Module + +Required properties: +- compatible: "ti,omap4-dmic" +- reg: Register location and size as an array: + <MPU access base address, size>, + <L3 interconnect address, size>; +- interrupts: Interrupt number for DMIC +- interrupt-parent: The parent interrupt controller +- ti,hwmods: Name of the hwmod associated with OMAP dmic IP + +Example: + +dmic: dmic@4012e000 { + compatible = "ti,omap4-dmic"; + reg = <0x4012e000 0x7f>, /* MPU private access */ + <0x4902e000 0x7f>; /* L3 Interconnect */ + interrupts = <0 114 0x4>; + interrupt-parent = <&gic>; + ti,hwmods = "dmic"; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt new file mode 100644 index 000000000000..0741dff048dd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt @@ -0,0 +1,21 @@ +* Texas Instruments OMAP4+ McPDM + +Required properties: +- compatible: "ti,omap4-mcpdm" +- reg: Register location and size as an array: + <MPU access base address, size>, + <L3 interconnect address, size>; +- interrupts: Interrupt number for McPDM +- interrupt-parent: The parent interrupt controller +- ti,hwmods: Name of the hwmod associated to the McPDM + +Example: + +mcpdm: mcpdm@40132000 { + compatible = "ti,omap4-mcpdm"; + reg = <0x40132000 0x7f>, /* MPU private access */ + <0x49032000 0x7f>; /* L3 Interconnect */ + interrupts = <0 112 0x4>; + interrupt-parent = <&gic>; + ti,hwmods = "mcpdm"; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt index a9c0406280e8..b462d0c54823 100644 --- a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt @@ -11,7 +11,7 @@ Optional properties: Example: -uart@73fbc000 { +serial@73fbc000 { compatible = "fsl,imx51-uart", "fsl,imx21-uart"; reg = <0x73fbc000 0x4000>; interrupts = <31>; diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/tegra-usb.txt index 007005ddbe12..e9b005dc7625 100644 --- a/Documentation/devicetree/bindings/usb/tegra-usb.txt +++ b/Documentation/devicetree/bindings/usb/tegra-usb.txt @@ -12,6 +12,9 @@ Required properties : - nvidia,vbus-gpio : If present, specifies a gpio that needs to be activated for the bus to be powered. +Required properties for phy_type == ulpi: + - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. + Optional properties: - dr_mode : dual role mode. Indicates the working mode for nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral", diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 107d8addf0e4..6eab91747a86 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -14,6 +14,7 @@ chrp Common Hardware Reference Platform cortina Cortina Systems, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) denx Denx Software Engineering +emmicro EM Microelectronic epson Seiko Epson Corp. est ESTeem Wireless Modems fsl Freescale Semiconductor diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index da0bfeb4253d..d4d66757354e 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -551,12 +551,13 @@ Here is an example of a simple device-tree. In this example, an "o" designates a node followed by the node unit name. Properties are presented with their name followed by their content. "content" represents an ASCII string (zero terminated) value, while <content> -represents a 32-bit hexadecimal value. The various nodes in this -example will be discussed in a later chapter. At this point, it is -only meant to give you a idea of what a device-tree looks like. I have -purposefully kept the "name" and "linux,phandle" properties which -aren't necessary in order to give you a better idea of what the tree -looks like in practice. +represents a 32-bit value, specified in decimal or hexadecimal (the +latter prefixed 0x). The various nodes in this example will be +discussed in a later chapter. At this point, it is only meant to give +you a idea of what a device-tree looks like. I have purposefully kept +the "name" and "linux,phandle" properties which aren't necessary in +order to give you a better idea of what the tree looks like in +practice. / o device-tree |- name = "device-tree" @@ -576,14 +577,14 @@ looks like in practice. | |- name = "PowerPC,970" | |- device_type = "cpu" | |- reg = <0> - | |- clock-frequency = <5f5e1000> + | |- clock-frequency = <0x5f5e1000> | |- 64-bit | |- linux,phandle = <2> | o memory@0 | |- name = "memory" | |- device_type = "memory" - | |- reg = <00000000 00000000 00000000 20000000> + | |- reg = <0x00000000 0x00000000 0x00000000 0x20000000> | |- linux,phandle = <3> | o chosen @@ -1010,8 +1011,8 @@ compatibility. #size-cells = <1>; #interrupt-cells = <2>; device_type = "soc"; - ranges = <00000000 e0000000 00100000> - reg = <e0000000 00003000>; + ranges = <0x00000000 0xe0000000 0x00100000> + reg = <0xe0000000 0x00003000>; bus-frequency = <0>; } @@ -1085,16 +1086,16 @@ supported currently at the toplevel. * terminated string */ - property2 = <1234abcd>; /* define a property containing a + property2 = <0x1234abcd>; /* define a property containing a * numerical 32-bit value (hexadecimal) */ - property3 = <12345678 12345678 deadbeef>; + property3 = <0x12345678 0x12345678 0xdeadbeef>; /* define a property containing 3 * numerical 32-bit values (cells) in * hexadecimal */ - property4 = [0a 0b 0c 0d de ea ad be ef]; + property4 = [0x0a 0x0b 0x0c 0x0d 0xde 0xea 0xad 0xbe 0xef]; /* define a property whose content is * an arbitrary array of bytes */ @@ -1350,10 +1351,10 @@ Appendix A - Sample SOC node for MPC8540 model = "TSEC"; compatible = "gianfar", "simple-bus"; reg = <0x24000 0x1000>; - local-mac-address = [ 00 E0 0C 00 73 00 ]; - interrupts = <29 2 30 2 34 2>; + local-mac-address = [ 0x00 0xE0 0x0C 0x00 0x73 0x00 ]; + interrupts = <0x29 2 0x30 2 0x34 2>; phy-handle = <&phy0>; - sleep = <&pmc 00000080>; + sleep = <&pmc 0x00000080>; ranges; mdio@24520 { @@ -1385,10 +1386,10 @@ Appendix A - Sample SOC node for MPC8540 model = "TSEC"; compatible = "gianfar"; reg = <0x25000 0x1000>; - local-mac-address = [ 00 E0 0C 00 73 01 ]; - interrupts = <13 2 14 2 18 2>; + local-mac-address = [ 0x00 0xE0 0x0C 0x00 0x73 0x01 ]; + interrupts = <0x13 2 0x14 2 0x18 2>; phy-handle = <&phy1>; - sleep = <&pmc 00000040>; + sleep = <&pmc 0x00000040>; }; ethernet@26000 { @@ -1396,17 +1397,17 @@ Appendix A - Sample SOC node for MPC8540 model = "FEC"; compatible = "gianfar"; reg = <0x26000 0x1000>; - local-mac-address = [ 00 E0 0C 00 73 02 ]; - interrupts = <41 2>; + local-mac-address = [ 0x00 0xE0 0x0C 0x00 0x73 0x02 ]; + interrupts = <0x41 2>; phy-handle = <&phy3>; - sleep = <&pmc 00000020>; + sleep = <&pmc 0x00000020>; }; serial@4500 { #address-cells = <1>; #size-cells = <1>; compatible = "fsl,mpc8540-duart", "simple-bus"; - sleep = <&pmc 00000002>; + sleep = <&pmc 0x00000002>; ranges; serial@4500 { @@ -1414,7 +1415,7 @@ Appendix A - Sample SOC node for MPC8540 compatible = "ns16550"; reg = <0x4500 0x100>; clock-frequency = <0>; - interrupts = <42 2>; + interrupts = <0x42 2>; }; serial@4600 { @@ -1422,7 +1423,7 @@ Appendix A - Sample SOC node for MPC8540 compatible = "ns16550"; reg = <0x4600 0x100>; clock-frequency = <0>; - interrupts = <42 2>; + interrupts = <0x42 2>; }; }; @@ -1436,11 +1437,11 @@ Appendix A - Sample SOC node for MPC8540 }; i2c@3000 { - interrupts = <43 2>; + interrupts = <0x43 2>; reg = <0x3000 0x100>; compatible = "fsl-i2c"; dfsrr; - sleep = <&pmc 00000004>; + sleep = <&pmc 0x00000004>; }; pmc: power@e0070 { diff --git a/Documentation/dma-buf-sharing.txt b/Documentation/dma-buf-sharing.txt index 3bbd5c51605a..ad86fb86c9a0 100644 --- a/Documentation/dma-buf-sharing.txt +++ b/Documentation/dma-buf-sharing.txt @@ -29,13 +29,6 @@ The buffer-user in memory, mapped into its own address space, so it can access the same area of memory. -*IMPORTANT*: [see https://lkml.org/lkml/2011/12/20/211 for more details] -For this first version, A buffer shared using the dma_buf sharing API: -- *may* be exported to user space using "mmap" *ONLY* by exporter, outside of - this framework. -- with this new iteration of the dma-buf api cpu access from the kernel has been - enable, see below for the details. - dma-buf operations for device dma only -------------------------------------- @@ -300,6 +293,17 @@ Access to a dma_buf from the kernel context involves three steps: Note that these calls need to always succeed. The exporter needs to complete any preparations that might fail in begin_cpu_access. + For some cases the overhead of kmap can be too high, a vmap interface + is introduced. This interface should be used very carefully, as vmalloc + space is a limited resources on many architectures. + + Interfaces: + void *dma_buf_vmap(struct dma_buf *dmabuf) + void dma_buf_vunmap(struct dma_buf *dmabuf, void *vaddr) + + The vmap call can fail if there is no vmap support in the exporter, or if it + runs out of vmalloc space. Fallback to kmap should be implemented. + 3. Finish access When the importer is done accessing the range specified in begin_cpu_access, @@ -313,6 +317,83 @@ Access to a dma_buf from the kernel context involves three steps: enum dma_data_direction dir); +Direct Userspace Access/mmap Support +------------------------------------ + +Being able to mmap an export dma-buf buffer object has 2 main use-cases: +- CPU fallback processing in a pipeline and +- supporting existing mmap interfaces in importers. + +1. CPU fallback processing in a pipeline + + In many processing pipelines it is sometimes required that the cpu can access + the data in a dma-buf (e.g. for thumbnail creation, snapshots, ...). To avoid + the need to handle this specially in userspace frameworks for buffer sharing + it's ideal if the dma_buf fd itself can be used to access the backing storage + from userspace using mmap. + + Furthermore Android's ION framework already supports this (and is otherwise + rather similar to dma-buf from a userspace consumer side with using fds as + handles, too). So it's beneficial to support this in a similar fashion on + dma-buf to have a good transition path for existing Android userspace. + + No special interfaces, userspace simply calls mmap on the dma-buf fd. + +2. Supporting existing mmap interfaces in exporters + + Similar to the motivation for kernel cpu access it is again important that + the userspace code of a given importing subsystem can use the same interfaces + with a imported dma-buf buffer object as with a native buffer object. This is + especially important for drm where the userspace part of contemporary OpenGL, + X, and other drivers is huge, and reworking them to use a different way to + mmap a buffer rather invasive. + + The assumption in the current dma-buf interfaces is that redirecting the + initial mmap is all that's needed. A survey of some of the existing + subsystems shows that no driver seems to do any nefarious thing like syncing + up with outstanding asynchronous processing on the device or allocating + special resources at fault time. So hopefully this is good enough, since + adding interfaces to intercept pagefaults and allow pte shootdowns would + increase the complexity quite a bit. + + Interface: + int dma_buf_mmap(struct dma_buf *, struct vm_area_struct *, + unsigned long); + + If the importing subsystem simply provides a special-purpose mmap call to set + up a mapping in userspace, calling do_mmap with dma_buf->file will equally + achieve that for a dma-buf object. + +3. Implementation notes for exporters + + Because dma-buf buffers have invariant size over their lifetime, the dma-buf + core checks whether a vma is too large and rejects such mappings. The + exporter hence does not need to duplicate this check. + + Because existing importing subsystems might presume coherent mappings for + userspace, the exporter needs to set up a coherent mapping. If that's not + possible, it needs to fake coherency by manually shooting down ptes when + leaving the cpu domain and flushing caches at fault time. Note that all the + dma_buf files share the same anon inode, hence the exporter needs to replace + the dma_buf file stored in vma->vm_file with it's own if pte shootdown is + requred. This is because the kernel uses the underlying inode's address_space + for vma tracking (and hence pte tracking at shootdown time with + unmap_mapping_range). + + If the above shootdown dance turns out to be too expensive in certain + scenarios, we can extend dma-buf with a more explicit cache tracking scheme + for userspace mappings. But the current assumption is that using mmap is + always a slower path, so some inefficiencies should be acceptable. + + Exporters that shoot down mappings (for any reasons) shall not do any + synchronization at fault time with outstanding device operations. + Synchronization is an orthogonal issue to sharing the backing storage of a + buffer and hence should not be handled by dma-buf itself. This is explictly + mentioned here because many people seem to want something like this, but if + different exporters handle this differently, buffer sharing can fail in + interesting ways depending upong the exporter (if userspace starts depending + upon this implicit synchronization). + Miscellaneous notes ------------------- @@ -336,6 +417,20 @@ Miscellaneous notes the exporting driver to create a dmabuf fd must provide a way to let userspace control setting of O_CLOEXEC flag passed in to dma_buf_fd(). +- If an exporter needs to manually flush caches and hence needs to fake + coherency for mmap support, it needs to be able to zap all the ptes pointing + at the backing storage. Now linux mm needs a struct address_space associated + with the struct file stored in vma->vm_file to do that with the function + unmap_mapping_range. But the dma_buf framework only backs every dma_buf fd + with the anon_file struct file, i.e. all dma_bufs share the same file. + + Hence exporters need to setup their own file (and address_space) association + by setting vma->vm_file and adjusting vma->vm_pgoff in the dma_buf mmap + callback. In the specific case of a gem driver the exporter could use the + shmem file already provided by gem (and set vm_pgoff = 0). Exporters can then + zap ptes by unmapping the corresponding range of the struct address_space + associated with their own file. + References: [1] struct dma_buf_ops in include/linux/dma-buf.h [2] All interfaces mentioned above defined in include/linux/dma-buf.h diff --git a/Documentation/dvb/get_dvb_firmware b/Documentation/dvb/get_dvb_firmware index d1d4a179a382..fbb241174486 100755 --- a/Documentation/dvb/get_dvb_firmware +++ b/Documentation/dvb/get_dvb_firmware @@ -28,7 +28,8 @@ use IO::Handle; "opera1", "cx231xx", "cx18", "cx23885", "pvrusb2", "mpc718", "af9015", "ngene", "az6027", "lme2510_lg", "lme2510c_s7395", "lme2510c_s7395_old", "drxk", "drxk_terratec_h5", - "drxk_hauppauge_hvr930c", "tda10071", "it9135", "it9137"); + "drxk_hauppauge_hvr930c", "tda10071", "it9135", "it9137", + "drxk_pctv"); # Check args syntax() if (scalar(@ARGV) != 1); @@ -730,6 +731,23 @@ sub tda10071 { "$fwfile"; } +sub drxk_pctv { + my $sourcefile = "PCTV_460e_reference.zip"; + my $url = "ftp://ftp.pctvsystems.com/TV/driver/PCTV%2070e%2080e%20100e%20320e%20330e%20800e/"; + my $hash = "4403de903bf2593464c8d74bbc200a57"; + my $fwfile = "dvb-demod-drxk-pctv.fw"; + my $tmpdir = tempdir(DIR => "/tmp", CLEANUP => 1); + + checkstandard(); + + wgetfile($sourcefile, $url . $sourcefile); + verify($sourcefile, $hash); + unzip($sourcefile, $tmpdir); + extract("$tmpdir/PCTV\ 70e\ 80e\ 100e\ 320e\ 330e\ 800e/32\ bit/emOEM.sys", 0x72b80, 42692, $fwfile); + + "$fwfile"; +} + # --------------------------------------------------------------- # Utilities diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 1e69a81e99d4..56000b33340b 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -541,6 +541,18 @@ Who: Kees Cook <keescook@chromium.org> ---------------------------- +What: Removing the pn544 raw driver. +When: 3.6 +Why: With the introduction of the NFC HCI and SHDL kernel layers, pn544.c + is being replaced by pn544_hci.c which is accessible through the netlink + and socket NFC APIs. Moreover, pn544.c is outdated and does not seem to + work properly with the latest Android stacks. + Having 2 drivers for the same hardware is confusing and as such we + should only keep the one following the kernel NFC APIs. +Who: Samuel Ortiz <sameo@linux.intel.com> + +---------------------------- + What: setitimer accepts user NULL pointer (value) When: 3.6 Why: setitimer is not returning -EFAULT if user pointer is NULL. This @@ -549,6 +561,15 @@ Who: Sasikantha Babu <sasikanth.v19@gmail.com> ---------------------------- +What: remove bogus DV presets V4L2_DV_1080I29_97, V4L2_DV_1080I30 and + V4L2_DV_1080I25 +When: 3.6 +Why: These HDTV formats do not exist and were added by a confused mind + (that was me, to be precise...) +Who: Hans Verkuil <hans.verkuil@cisco.com> + +---------------------------- + What: V4L2_CID_HCENTER, V4L2_CID_VCENTER V4L2 controls When: 3.7 Why: The V4L2_CID_VCENTER, V4L2_CID_HCENTER controls have been deprecated @@ -567,3 +588,27 @@ Why: Remount currently allows changing bound subsystems and replaced with conventional fsnotify. ---------------------------- + +What: KVM debugfs statistics +When: 2013 +Why: KVM tracepoints provide mostly equivalent information in a much more + flexible fashion. + +---------------------------- + +What: at91-mci driver ("CONFIG_MMC_AT91") +When: 3.7 +Why: There are two mci drivers: at91-mci and atmel-mci. The PDC support + was added to atmel-mci as a first step to support more chips. + Then at91-mci was kept only for old IP versions (on at91rm9200 and + at91sam9261). The support of these IP versions has just been added + to atmel-mci, so atmel-mci can be used for all chips. +Who: Ludovic Desroches <ludovic.desroches@atmel.com> + +---------------------------- + +What: net/wanrouter/ +When: June 2013 +Why: Unsupported/unmaintained/unused since 2.6 + +---------------------------- diff --git a/Documentation/filesystems/Locking b/Documentation/filesystems/Locking index 4fca82e5276e..d449e632e6a0 100644 --- a/Documentation/filesystems/Locking +++ b/Documentation/filesystems/Locking @@ -60,7 +60,6 @@ ata *); ssize_t (*getxattr) (struct dentry *, const char *, void *, size_t); ssize_t (*listxattr) (struct dentry *, char *, size_t); int (*removexattr) (struct dentry *, const char *); - void (*truncate_range)(struct inode *, loff_t, loff_t); int (*fiemap)(struct inode *, struct fiemap_extent_info *, u64 start, u64 len); locking rules: @@ -87,7 +86,6 @@ setxattr: yes getxattr: no listxattr: no removexattr: yes -truncate_range: yes fiemap: no Additionally, ->rmdir(), ->unlink() and ->rename() have ->i_mutex on victim. diff --git a/Documentation/filesystems/ext3.txt b/Documentation/filesystems/ext3.txt index b100adc38adb..293855e95000 100644 --- a/Documentation/filesystems/ext3.txt +++ b/Documentation/filesystems/ext3.txt @@ -59,9 +59,9 @@ commit=nrsec (*) Ext3 can be told to sync all its data and metadata Setting it to very large values will improve performance. -barrier=<0(*)|1> This enables/disables the use of write barriers in -barrier the jbd code. barrier=0 disables, barrier=1 enables. -nobarrier (*) This also requires an IO stack which can support +barrier=<0|1(*)> This enables/disables the use of write barriers in +barrier (*) the jbd code. barrier=0 disables, barrier=1 enables. +nobarrier This also requires an IO stack which can support barriers, and if jbd gets an error on a barrier write, it will disable again with a warning. Write barriers enforce proper on-disk ordering diff --git a/Documentation/filesystems/porting b/Documentation/filesystems/porting index 74acd9618819..8c91d1057d9a 100644 --- a/Documentation/filesystems/porting +++ b/Documentation/filesystems/porting @@ -297,7 +297,8 @@ in the beginning of ->setattr unconditionally. be used instead. It gets called whenever the inode is evicted, whether it has remaining links or not. Caller does *not* evict the pagecache or inode-associated metadata buffers; getting rid of those is responsibility of method, as it had -been for ->delete_inode(). +been for ->delete_inode(). Caller makes sure async writeback cannot be running +for the inode while (or after) ->evict_inode() is called. ->drop_inode() returns int now; it's called on final iput() with inode->i_lock held and it returns true if filesystems wants the inode to be @@ -306,14 +307,11 @@ updated appropriately. generic_delete_inode() is also alive and it consists simply of return 1. Note that all actual eviction work is done by caller after ->drop_inode() returns. - clear_inode() is gone; use end_writeback() instead. As before, it must -be called exactly once on each call of ->evict_inode() (as it used to be for -each call of ->delete_inode()). Unlike before, if you are using inode-associated -metadata buffers (i.e. mark_buffer_dirty_inode()), it's your responsibility to -call invalidate_inode_buffers() before end_writeback(). - No async writeback (and thus no calls of ->write_inode()) will happen -after end_writeback() returns, so actions that should not overlap with ->write_inode() -(e.g. freeing on-disk inode if i_nlink is 0) ought to be done after that call. + As before, clear_inode() must be called exactly once on each call of +->evict_inode() (as it used to be for each call of ->delete_inode()). Unlike +before, if you are using inode-associated metadata buffers (i.e. +mark_buffer_dirty_inode()), it's your responsibility to call +invalidate_inode_buffers() before clear_inode(). NOTE: checking i_nlink in the beginning of ->write_inode() and bailing out if it's zero is not *and* *never* *had* *been* enough. Final unlink() and iput() diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index ef088e55ab2e..fb0a6aeb936c 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -40,6 +40,7 @@ Table of Contents 3.4 /proc/<pid>/coredump_filter - Core dump filtering settings 3.5 /proc/<pid>/mountinfo - Information about mounts 3.6 /proc/<pid>/comm & /proc/<pid>/task/<tid>/comm + 3.7 /proc/<pid>/task/<tid>/children - Information about task children 4 Configuring procfs 4.1 Mount options @@ -310,6 +311,11 @@ Table 1-4: Contents of the stat files (as of 2.6.30-rc7) start_data address above which program data+bss is placed end_data address below which program data+bss is placed start_brk address above which program heap can be expanded with brk() + arg_start address above which program command line is placed + arg_end address below which program command line is placed + env_start address above which program environment is placed + env_end address below which program environment is placed + exit_code the thread's exit_code in the form reported by the waitpid system call .............................................................................. The /proc/PID/maps file containing the currently mapped memory regions and @@ -743,6 +749,7 @@ Committed_AS: 100056 kB VmallocTotal: 112216 kB VmallocUsed: 428 kB VmallocChunk: 111088 kB +AnonHugePages: 49152 kB MemTotal: Total usable ram (i.e. physical ram minus a few reserved bits and the kernel binary code) @@ -776,6 +783,7 @@ VmallocChunk: 111088 kB Dirty: Memory which is waiting to get written back to the disk Writeback: Memory which is actively being written back to the disk AnonPages: Non-file backed pages mapped into userspace page tables +AnonHugePages: Non-file backed huge pages mapped into userspace page tables Mapped: files which have been mmaped, such as libraries Slab: in-kernel data structures cache SReclaimable: Part of Slab, that might be reclaimed, such as caches @@ -1576,6 +1584,23 @@ then the kernel's TASK_COMM_LEN (currently 16 chars) will result in a truncated comm value. +3.7 /proc/<pid>/task/<tid>/children - Information about task children +------------------------------------------------------------------------- +This file provides a fast way to retrieve first level children pids +of a task pointed by <pid>/<tid> pair. The format is a space separated +stream of pids. + +Note the "first level" here -- if a child has own children they will +not be listed here, one needs to read /proc/<children-pid>/task/<tid>/children +to obtain the descendants. + +Since this interface is intended to be fast and cheap it doesn't +guarantee to provide precise results and some children might be +skipped, especially if they've exited right after we printed their +pids, so one need to either stop or freeze processes being inspected +if precise results are needed. + + ------------------------------------------------------------------------------ Configuring procfs ------------------------------------------------------------------------------ diff --git a/Documentation/filesystems/vfs.txt b/Documentation/filesystems/vfs.txt index 0d0492028082..ef19f91a0f12 100644 --- a/Documentation/filesystems/vfs.txt +++ b/Documentation/filesystems/vfs.txt @@ -363,7 +363,6 @@ struct inode_operations { ssize_t (*getxattr) (struct dentry *, const char *, void *, size_t); ssize_t (*listxattr) (struct dentry *, char *, size_t); int (*removexattr) (struct dentry *, const char *); - void (*truncate_range)(struct inode *, loff_t, loff_t); }; Again, all methods are called without any locks being held, unless @@ -472,9 +471,6 @@ otherwise noted. removexattr: called by the VFS to remove an extended attribute from a file. This method is called by removexattr(2) system call. - truncate_range: a method provided by the underlying filesystem to truncate a - range of blocks , i.e. punch a hole somewhere in a file. - The Address Space Object ======================== @@ -760,7 +756,7 @@ struct file_operations ---------------------- This describes how the VFS can manipulate an open file. As of kernel -2.6.22, the following members are defined: +3.5, the following members are defined: struct file_operations { struct module *owner; @@ -790,6 +786,8 @@ struct file_operations { int (*flock) (struct file *, int, struct file_lock *); ssize_t (*splice_write)(struct pipe_inode_info *, struct file *, size_t, unsigned int); ssize_t (*splice_read)(struct file *, struct pipe_inode_info *, size_t, unsigned int); + int (*setlease)(struct file *, long arg, struct file_lock **); + long (*fallocate)(struct file *, int mode, loff_t offset, loff_t len); }; Again, all methods are called without any locks being held, unless @@ -858,6 +856,11 @@ otherwise noted. splice_read: called by the VFS to splice data from file to a pipe. This method is used by the splice(2) system call + setlease: called by the VFS to set or release a file lock lease. + setlease has the file_lock_lock held and must not sleep. + + fallocate: called by the VFS to preallocate blocks or punch a hole. + Note that the file operations are implemented by the specific filesystem in which the inode resides. When opening a device node (character or block special) most filesystems will call special diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt index 620a07844e8c..e08a883de36e 100644 --- a/Documentation/gpio.txt +++ b/Documentation/gpio.txt @@ -322,6 +322,9 @@ where 'flags' is currently defined to specify the following properties: * GPIOF_OPEN_DRAIN - gpio pin is open drain type. * GPIOF_OPEN_SOURCE - gpio pin is open source type. + * GPIOF_EXPORT_DIR_FIXED - export gpio to sysfs, keep direction + * GPIOF_EXPORT_DIR_CHANGEABLE - also export, allow changing direction + since GPIOF_INIT_* are only valid when configured as output, so group valid combinations as: diff --git a/Documentation/i2c/functionality b/Documentation/i2c/functionality index 42c17c1fb3cd..b0ff2ab596ce 100644 --- a/Documentation/i2c/functionality +++ b/Documentation/i2c/functionality @@ -18,9 +18,9 @@ For the most up-to-date list of functionality constants, please check adapters typically can not do these) I2C_FUNC_10BIT_ADDR Handles the 10-bit address extensions I2C_FUNC_PROTOCOL_MANGLING Knows about the I2C_M_IGNORE_NAK, - I2C_M_REV_DIR_ADDR, I2C_M_NOSTART and - I2C_M_NO_RD_ACK flags (which modify the - I2C protocol!) + I2C_M_REV_DIR_ADDR and I2C_M_NO_RD_ACK + flags (which modify the I2C protocol!) + I2C_FUNC_NOSTART Can skip repeated start sequence I2C_FUNC_SMBUS_QUICK Handles the SMBus write_quick command I2C_FUNC_SMBUS_READ_BYTE Handles the SMBus read_byte command I2C_FUNC_SMBUS_WRITE_BYTE Handles the SMBus write_byte command @@ -50,6 +50,9 @@ A few combinations of the above flags are also defined for your convenience: emulated by a real I2C adapter (using the transparent emulation layer) +In kernel versions prior to 3.5 I2C_FUNC_NOSTART was implemented as +part of I2C_FUNC_PROTOCOL_MANGLING. + ADAPTER IMPLEMENTATION ---------------------- diff --git a/Documentation/i2c/i2c-protocol b/Documentation/i2c/i2c-protocol index 10518dd58814..0b3e62d1f77a 100644 --- a/Documentation/i2c/i2c-protocol +++ b/Documentation/i2c/i2c-protocol @@ -49,7 +49,9 @@ a byte read, followed by a byte write: Modified transactions ===================== -We have found some I2C devices that needs the following modifications: +The following modifications to the I2C protocol can also be generated, +with the exception of I2C_M_NOSTART these are usually only needed to +work around device issues: Flag I2C_M_NOSTART: In a combined transaction, no 'S Addr Wr/Rd [A]' is generated at some @@ -60,6 +62,11 @@ We have found some I2C devices that needs the following modifications: we do not generate Addr, but we do generate the startbit S. This will probably confuse all other clients on your bus, so don't try this. + This is often used to gather transmits from multiple data buffers in + system memory into something that appears as a single transfer to the + I2C device but may also be used between direction changes by some + rare devices. + Flags I2C_M_REV_DIR_ADDR This toggles the Rd/Wr flag. That is, if you want to do a write, but need to emit an Rd instead of a Wr, or vice versa, you set this diff --git a/Documentation/i2c/muxes/gpio-i2cmux b/Documentation/i2c/muxes/i2c-mux-gpio index 811cd78d4cdc..bd9b2299b739 100644 --- a/Documentation/i2c/muxes/gpio-i2cmux +++ b/Documentation/i2c/muxes/i2c-mux-gpio @@ -1,11 +1,11 @@ -Kernel driver gpio-i2cmux +Kernel driver i2c-gpio-mux Author: Peter Korsgaard <peter.korsgaard@barco.com> Description ----------- -gpio-i2cmux is an i2c mux driver providing access to I2C bus segments +i2c-gpio-mux is an i2c mux driver providing access to I2C bus segments from a master I2C bus and a hardware MUX controlled through GPIO pins. E.G.: @@ -26,16 +26,16 @@ according to the settings of the GPIO pins 1..N. Usage ----- -gpio-i2cmux uses the platform bus, so you need to provide a struct +i2c-gpio-mux uses the platform bus, so you need to provide a struct platform_device with the platform_data pointing to a struct gpio_i2cmux_platform_data with the I2C adapter number of the master bus, the number of bus segments to create and the GPIO pins used -to control it. See include/linux/gpio-i2cmux.h for details. +to control it. See include/linux/i2c-gpio-mux.h for details. E.G. something like this for a MUX providing 4 bus segments controlled through 3 GPIO pins: -#include <linux/gpio-i2cmux.h> +#include <linux/i2c-gpio-mux.h> #include <linux/platform_device.h> static const unsigned myboard_gpiomux_gpios[] = { @@ -57,7 +57,7 @@ static struct gpio_i2cmux_platform_data myboard_i2cmux_data = { }; static struct platform_device myboard_i2cmux = { - .name = "gpio-i2cmux", + .name = "i2c-gpio-mux", .id = 0, .dev = { .platform_data = &myboard_i2cmux_data, diff --git a/Documentation/initrd.txt b/Documentation/initrd.txt index 1ba84f3584e3..4e1839ccb555 100644 --- a/Documentation/initrd.txt +++ b/Documentation/initrd.txt @@ -362,5 +362,5 @@ Resources http://www.almesberger.net/cv/papers/ols2k-9.ps.gz [2] newlib package (experimental), with initrd example http://sources.redhat.com/newlib/ -[3] Brouwer, Andries; "util-linux: Miscellaneous utilities for Linux" - ftp://ftp.win.tue.nl/pub/linux-local/utils/util-linux/ +[3] util-linux: Miscellaneous utilities for Linux + http://www.kernel.org/pub/linux/utils/util-linux/ diff --git a/Documentation/kbuild/kbuild.txt b/Documentation/kbuild/kbuild.txt index 68e32bb6bd80..6466704d47b5 100644 --- a/Documentation/kbuild/kbuild.txt +++ b/Documentation/kbuild/kbuild.txt @@ -50,6 +50,10 @@ LDFLAGS_MODULE -------------------------------------------------- Additional options used for $(LD) when linking modules. +LDFLAGS_vmlinux +-------------------------------------------------- +Additional options passed to final link of vmlinux. + KBUILD_VERBOSE -------------------------------------------------- Set the kbuild verbosity. Can be assigned same values as "V=...". @@ -214,3 +218,18 @@ KBUILD_BUILD_USER, KBUILD_BUILD_HOST These two variables allow to override the user@host string displayed during boot and in /proc/version. The default value is the output of the commands whoami and host, respectively. + +KBUILD_LDS +-------------------------------------------------- +The linker script with full path. Assigned by the top-level Makefile. + +KBUILD_VMLINUX_INIT +-------------------------------------------------- +All object files for the init (first) part of vmlinux. +Files specified with KBUILD_VMLINUX_INIT are linked first. + +KBUILD_VMLINUX_MAIN +-------------------------------------------------- +All object files for the main part of vmlinux. +KBUILD_VMLINUX_INIT and KBUILD_VMLINUX_MAIN together specify +all the object files used to link vmlinux. diff --git a/Documentation/kbuild/kconfig.txt b/Documentation/kbuild/kconfig.txt index 9d5f2a90dca9..a09f1a6a830c 100644 --- a/Documentation/kbuild/kconfig.txt +++ b/Documentation/kbuild/kconfig.txt @@ -53,15 +53,15 @@ KCONFIG_ALLCONFIG -------------------------------------------------- (partially based on lkml email from/by Rob Landley, re: miniconfig) -------------------------------------------------- -The allyesconfig/allmodconfig/allnoconfig/randconfig variants can -also use the environment variable KCONFIG_ALLCONFIG as a flag or a -filename that contains config symbols that the user requires to be -set to a specific value. If KCONFIG_ALLCONFIG is used without a -filename, "make *config" checks for a file named -"all{yes/mod/no/def/random}.config" (corresponding to the *config command -that was used) for symbol values that are to be forced. If this file -is not found, it checks for a file named "all.config" to contain forced -values. +The allyesconfig/allmodconfig/allnoconfig/randconfig variants can also +use the environment variable KCONFIG_ALLCONFIG as a flag or a filename +that contains config symbols that the user requires to be set to a +specific value. If KCONFIG_ALLCONFIG is used without a filename where +KCONFIG_ALLCONFIG == "" or KCONFIG_ALLCONFIG == "1", "make *config" +checks for a file named "all{yes/mod/no/def/random}.config" +(corresponding to the *config command that was used) for symbol values +that are to be forced. If this file is not found, it checks for a +file named "all.config" to contain forced values. This enables you to create "miniature" config (miniconfig) or custom config files containing just the config symbols that you are interested diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 5b6e58492229..c45513d806ab 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -335,6 +335,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. requirements as needed. This option does not override iommu=pt + amd_iommu_dump= [HW,X86-64] + Enable AMD IOMMU driver option to dump the ACPI table + for AMD IOMMU. With this option enabled, AMD IOMMU + driver will print ACPI tables for AMD IOMMU during + IOMMU initialization. + amijoy.map= [HW,JOY] Amiga joystick support Map of devices attached to JOY0DAT and JOY1DAT Format: <a>,<b> @@ -397,8 +403,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted. atkbd.softrepeat= [HW] Use software keyboard repeat - autotest [IA-64] - baycom_epp= [HW,AX25] Format: <io>,<mode> @@ -508,6 +512,11 @@ bytes respectively. Such letter suffixes can also be entirely omitted. Also note the kernel might malfunction if you disable some critical bits. + cma=nn[MG] [ARM,KNL] + Sets the size of kernel global memory area for contiguous + memory allocations. For more information, see + include/linux/dma-contiguous.h + cmo_free_hint= [PPC] Format: { yes | no } Specify whether pages are marked as being inactive when they are freed. This is used in CMO environments @@ -515,6 +524,10 @@ bytes respectively. Such letter suffixes can also be entirely omitted. a hypervisor. Default: yes + coherent_pool=nn[KMG] [ARM,KNL] + Sets the size of memory pool for coherent, atomic dma + allocations if Contiguous Memory Allocator (CMA) is used. + code_bytes [X86] How many bytes of object code to print in an oops report. Range: 0 - 8192 @@ -987,6 +1000,20 @@ bytes respectively. Such letter suffixes can also be entirely omitted. i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN capability is set. + i915.invert_brightness= + [DRM] Invert the sense of the variable that is used to + set the brightness of the panel backlight. Normally a + brightness value of 0 indicates backlight switched off, + and the maximum of the brightness value sets the backlight + to maximum brightness. If this parameter is set to 0 + (default) and the machine requires it, or this parameter + is set to 1, a brightness value of 0 sets the backlight + to maximum brightness, and the maximum of the brightness + value switches the backlight off. + -1 -- never invert brightness + 0 -- machine default + 1 -- force brightness inversion + icn= [HW,ISDN] Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]] @@ -1430,8 +1457,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted. devices can be requested on-demand with the /dev/loop-control interface. - mcatest= [IA-64] - mce [X86-32] Machine Check Exception mce=option [X86-64] See Documentation/x86/x86_64/boot-options.txt diff --git a/Documentation/leds/ledtrig-transient.txt b/Documentation/leds/ledtrig-transient.txt new file mode 100644 index 000000000000..3bd38b487df1 --- /dev/null +++ b/Documentation/leds/ledtrig-transient.txt @@ -0,0 +1,152 @@ +LED Transient Trigger +===================== + +The leds timer trigger does not currently have an interface to activate +a one shot timer. The current support allows for setting two timers, one for +specifying how long a state to be on, and the second for how long the state +to be off. The delay_on value specifies the time period an LED should stay +in on state, followed by a delay_off value that specifies how long the LED +should stay in off state. The on and off cycle repeats until the trigger +gets deactivated. There is no provision for one time activation to implement +features that require an on or off state to be held just once and then stay in +the original state forever. + +Without one shot timer interface, user space can still use timer trigger to +set a timer to hold a state, however when user space application crashes or +goes away without deactivating the timer, the hardware will be left in that +state permanently. + +As a specific example of this use-case, let's look at vibrate feature on +phones. Vibrate function on phones is implemented using PWM pins on SoC or +PMIC. There is a need to activate one shot timer to control the vibrate +feature, to prevent user space crashes leaving the phone in vibrate mode +permanently causing the battery to drain. + +Transient trigger addresses the need for one shot timer activation. The +transient trigger can be enabled and disabled just like the other leds +triggers. + +When an led class device driver registers itself, it can specify all leds +triggers it supports and a default trigger. During registration, activation +routine for the default trigger gets called. During registration of an led +class device, the LED state does not change. + +When the driver unregisters, deactivation routine for the currently active +trigger will be called, and LED state is changed to LED_OFF. + +Driver suspend changes the LED state to LED_OFF and resume doesn't change +the state. Please note that there is no explicit interaction between the +suspend and resume actions and the currently enabled trigger. LED state +changes are suspended while the driver is in suspend state. Any timers +that are active at the time driver gets suspended, continue to run, without +being able to actually change the LED state. Once driver is resumed, triggers +start functioning again. + +LED state changes are controlled using brightness which is a common led +class device property. When brightness is set to 0 from user space via +echo 0 > brightness, it will result in deactivating the current trigger. + +Transient trigger uses standard register and unregister interfaces. During +trigger registration, for each led class device that specifies this trigger +as its default trigger, trigger activation routine will get called. During +registration, the LED state does not change, unless there is another trigger +active, in which case LED state changes to LED_OFF. + +During trigger unregistration, LED state gets changed to LED_OFF. + +Transient trigger activation routine doesn't change the LED state. It +creates its properties and does its initialization. Transient trigger +deactivation routine, will cancel any timer that is active before it cleans +up and removes the properties it created. It will restore the LED state to +non-transient state. When driver gets suspended, irrespective of the transient +state, the LED state changes to LED_OFF. + +Transient trigger can be enabled and disabled from user space on led class +devices, that support this trigger as shown below: + +echo transient > trigger +echo none > trigger + +NOTE: Add a new property trigger state to control the state. + +This trigger exports three properties, activate, state, and duration. When +transient trigger is activated these properties are set to default values. + +- duration allows setting timer value in msecs. The initial value is 0. +- activate allows activating and deactivating the timer specified by + duration as needed. The initial and default value is 0. This will allow + duration to be set after trigger activation. +- state allows user to specify a transient state to be held for the specified + duration. + + activate - one shot timer activate mechanism. + 1 when activated, 0 when deactivated. + default value is zero when transient trigger is enabled, + to allow duration to be set. + + activate state indicates a timer with a value of specified + duration running. + deactivated state indicates that there is no active timer + running. + + duration - one shot timer value. When activate is set, duration value + is used to start a timer that runs once. This value doesn't + get changed by the trigger unless user does a set via + echo new_value > duration + + state - transient state to be held. It has two values 0 or 1. 0 maps + to LED_OFF and 1 maps to LED_FULL. The specified state is + held for the duration of the one shot timer and then the + state gets changed to the non-transient state which is the + inverse of transient state. + If state = LED_FULL, when the timer runs out the state will + go back to LED_OFF. + If state = LED_OFF, when the timer runs out the state will + go back to LED_FULL. + Please note that current LED state is not checked prior to + changing the state to the specified state. + Driver could map these values to inverted depending on the + default states it defines for the LED in its brightness_set() + interface which is called from the led brightness_set() + interfaces to control the LED state. + +When timer expires activate goes back to deactivated state, duration is left +at the set value to be used when activate is set at a future time. This will +allow user app to set the time once and activate it to run it once for the +specified value as needed. When timer expires, state is restored to the +non-transient state which is the inverse of the transient state. + + echo 1 > activate - starts timer = duration when duration is not 0. + echo 0 > activate - cancels currently running timer. + echo n > duration - stores timer value to be used upon next + activate. Currently active timer if + any, continues to run for the specified time. + echo 0 > duration - stores timer value to be used upon next + activate. Currently active timer if any, + continues to run for the specified time. + echo 1 > state - stores desired transient state LED_FULL to be + held for the specified duration. + echo 0 > state - stores desired transient state LED_OFF to be + held for the specified duration. + +What is not supported: +====================== +- Timer activation is one shot and extending and/or shortening the timer + is not supported. + +Example use-case 1: + echo transient > trigger + echo n > duration + echo 1 > state +repeat the following step as needed: + echo 1 > activate - start timer = duration to run once + echo 1 > activate - start timer = duration to run once + echo none > trigger + +This trigger is intended to be used for for the following example use cases: + - Control of vibrate (phones, tablets etc.) hardware by user space app. + - Use of LED by user space app as activity indicator. + - Use of LED by user space app as a kind of watchdog indicator -- as + long as the app is alive, it can keep the LED illuminated, if it dies + the LED will be extinguished automatically. + - Use by any user space app that needs a transient GPIO output. diff --git a/Documentation/media-framework.txt b/Documentation/media-framework.txt index 3a0f879533ce..802875413873 100644 --- a/Documentation/media-framework.txt +++ b/Documentation/media-framework.txt @@ -335,6 +335,9 @@ the media_entity pipe field. Calls to media_entity_pipeline_start() can be nested. The pipeline pointer must be identical for all nested calls to the function. +media_entity_pipeline_start() may return an error. In that case, it will +clean up any the changes it did by itself. + When stopping the stream, drivers must notify the entities with media_entity_pipeline_stop(struct media_entity *entity); @@ -351,3 +354,19 @@ If other operations need to be disallowed on streaming entities (such as changing entities configuration parameters) drivers can explicitly check the media_entity stream_count field to find out if an entity is streaming. This operation must be done with the media_device graph_mutex held. + + +Link validation +--------------- + +Link validation is performed by media_entity_pipeline_start() for any +entity which has sink pads in the pipeline. The +media_entity::link_validate() callback is used for that purpose. In +link_validate() callback, entity driver should check that the properties of +the source pad of the connected entity and its own sink pad match. It is up +to the type of the entity (and in the end, the properties of the hardware) +what matching actually means. + +Subsystems should facilitate link validation by providing subsystem specific +helper functions to provide easy access for commonly needed information, and +in the end provide a way to use driver-specific callbacks. diff --git a/Documentation/nfc/nfc-hci.txt b/Documentation/nfc/nfc-hci.txt index 216b7254fcc3..320f9336c781 100644 --- a/Documentation/nfc/nfc-hci.txt +++ b/Documentation/nfc/nfc-hci.txt @@ -22,9 +22,9 @@ response to arrive. HCI events can also be received from the host controller. They will be handled and a translation will be forwarded to NFC Core as needed. HCI uses 2 execution contexts: -- one if for executing commands : nfc_hci_msg_tx_work(). Only one command +- one for executing commands : nfc_hci_msg_tx_work(). Only one command can be executing at any given moment. -- one if for dispatching received events and responses : nfc_hci_msg_rx_work() +- one for dispatching received events and commands : nfc_hci_msg_rx_work(). HCI Session initialization: --------------------------- @@ -52,18 +52,42 @@ entry points: struct nfc_hci_ops { int (*open)(struct nfc_hci_dev *hdev); void (*close)(struct nfc_hci_dev *hdev); + int (*hci_ready) (struct nfc_hci_dev *hdev); int (*xmit)(struct nfc_hci_dev *hdev, struct sk_buff *skb); int (*start_poll)(struct nfc_hci_dev *hdev, u32 protocols); int (*target_from_gate)(struct nfc_hci_dev *hdev, u8 gate, struct nfc_target *target); + int (*complete_target_discovered) (struct nfc_hci_dev *hdev, u8 gate, + struct nfc_target *target); + int (*data_exchange) (struct nfc_hci_dev *hdev, + struct nfc_target *target, + struct sk_buff *skb, struct sk_buff **res_skb); + int (*check_presence)(struct nfc_hci_dev *hdev, + struct nfc_target *target); }; -open() and close() shall turn the hardware on and off. xmit() shall simply -write a frame to the chip. start_poll() is an optional entrypoint that shall -set the hardware in polling mode. This must be implemented only if the hardware -uses proprietary gates or a mechanism slightly different from the HCI standard. -target_from_gate() is another optional entrypoint to return the protocols +- open() and close() shall turn the hardware on and off. +- hci_ready() is an optional entry point that is called right after the hci +session has been set up. The driver can use it to do additional initialization +that must be performed using HCI commands. +- xmit() shall simply write a frame to the chip. +- start_poll() is an optional entrypoint that shall set the hardware in polling +mode. This must be implemented only if the hardware uses proprietary gates or a +mechanism slightly different from the HCI standard. +- target_from_gate() is an optional entrypoint to return the nfc protocols corresponding to a proprietary gate. +- complete_target_discovered() is an optional entry point to let the driver +perform additional proprietary processing necessary to auto activate the +discovered target. +- data_exchange() must be implemented by the driver if proprietary HCI commands +are required to send data to the tag. Some tag types will require custom +commands, others can be written to using the standard HCI commands. The driver +can check the tag type and either do proprietary processing, or return 1 to ask +for standard processing. +- check_presence() is an optional entry point that will be called regularly +by the core to check that an activated tag is still in the field. If this is +not implemented, the core will not be able to push tag_lost events to the user +space On the rx path, the driver is responsible to push incoming HCP frames to HCI using nfc_hci_recv_frame(). HCI will take care of re-aggregation and handling @@ -99,7 +123,8 @@ fast, cannot sleep. stores incoming frames into an shdlc rx queue handles shdlc rx & tx queues. Dispatches HCI cmd responses. - HCI Tx Cmd worker (MSGTXWQ) -Serialize execution of HCI commands. Complete execution in case of resp timeout. +Serializes execution of HCI commands. Completes execution in case of response +timeout. - HCI Rx worker (MSGRXWQ) Dispatches incoming HCI commands or events. @@ -133,11 +158,11 @@ able to complete the command with a timeout error if no response arrive. SMW context gets scheduled and invokes nfc_shdlc_sm_work(). This function handles shdlc framing in and out. It uses the driver xmit to send frames and receives incoming frames in an skb queue filled from the driver IRQ handler. -SHDLC I(nformation) frames payload are HCP fragments. They are agregated to +SHDLC I(nformation) frames payload are HCP fragments. They are aggregated to form complete HCI frames, which can be a response, command, or event. HCI Responses are dispatched immediately from this context to unblock -waiting command execution. Reponse processing involves invoking the completion +waiting command execution. Response processing involves invoking the completion callback that was provided by nfc_hci_msg_tx_work() when it sent the command. The completion callback will then wake the syscall context. diff --git a/Documentation/power/charger-manager.txt b/Documentation/power/charger-manager.txt index fdcca991df30..b4f7f4b23f64 100644 --- a/Documentation/power/charger-manager.txt +++ b/Documentation/power/charger-manager.txt @@ -44,6 +44,16 @@ Charger Manager supports the following: Normally, the platform will need to resume and suspend some devices that are used by Charger Manager. +* Support for premature full-battery event handling + If the battery voltage drops by "fullbatt_vchkdrop_uV" after + "fullbatt_vchkdrop_ms" from the full-battery event, the framework + restarts charging. This check is also performed while suspended by + setting wakeup time accordingly and using suspend_again. + +* Support for uevent-notify + With the charger-related events, the device sends + notification to users with UEVENT. + 2. Global Charger-Manager Data related with suspend_again ======================================================== In order to setup Charger Manager with suspend-again feature @@ -55,7 +65,7 @@ if there are multiple batteries. If there are multiple batteries, the multiple instances of Charger Manager share the same charger_global_desc and it will manage in-suspend monitoring for all instances of Charger Manager. -The user needs to provide all the two entries properly in order to activate +The user needs to provide all the three entries properly in order to activate in-suspend monitoring: struct charger_global_desc { @@ -74,6 +84,11 @@ bool (*rtc_only_wakeup)(void); same struct. If there is any other wakeup source triggered the wakeup, it should return false. If the "rtc" is the only wakeup reason, it should return true. + +bool assume_timer_stops_in_suspend; + : if true, Charger Manager assumes that + the timer (CM uses jiffies as timer) stops during suspend. Then, CM + assumes that the suspend-duration is same as the alarm length. }; 3. How to setup suspend_again @@ -111,6 +126,16 @@ enum polling_modes polling_mode; CM_POLL_CHARGING_ONLY: poll this battery if and only if the battery is being charged. +unsigned int fullbatt_vchkdrop_ms; +unsigned int fullbatt_vchkdrop_uV; + : If both have non-zero values, Charger Manager will check the + battery voltage drop fullbatt_vchkdrop_ms after the battery is fully + charged. If the voltage drop is over fullbatt_vchkdrop_uV, Charger + Manager will try to recharge the battery by disabling and enabling + chargers. Recharge with voltage drop condition only (without delay + condition) is needed to be implemented with hardware interrupts from + fuel gauges or charger devices/chips. + unsigned int fullbatt_uV; : If specified with a non-zero value, Charger Manager assumes that the battery is full (capacity = 100) if the battery is not being @@ -122,6 +147,8 @@ unsigned int polling_interval_ms; this battery every polling_interval_ms or more frequently. enum data_source battery_present; + : CM_BATTERY_PRESENT: assume that the battery exists. + CM_NO_BATTERY: assume that the battery does not exists. CM_FUEL_GAUGE: get battery presence information from fuel gauge. CM_CHARGER_STAT: get battery presence from chargers. @@ -151,7 +178,17 @@ bool measure_battery_temp; the value of measure_battery_temp. }; -5. Other Considerations +5. Notify Charger-Manager of charger events: cm_notify_event() +========================================================= +If there is an charger event is required to notify +Charger Manager, a charger device driver that triggers the event can call +cm_notify_event(psy, type, msg) to notify the corresponding Charger Manager. +In the function, psy is the charger driver's power_supply pointer, which is +associated with Charger-Manager. The parameter "type" +is the same as irq's type (enum cm_event_types). The event message "msg" is +optional and is effective only if the event type is "UNDESCRIBED" or "OTHERS". + +6. Other Considerations ======================= At the charger/battery-related events such as battery-pulled-out, diff --git a/Documentation/power/power_supply_class.txt b/Documentation/power/power_supply_class.txt index 9f16c5178b66..211831d4095f 100644 --- a/Documentation/power/power_supply_class.txt +++ b/Documentation/power/power_supply_class.txt @@ -84,6 +84,8 @@ are already charged or discharging, 'n/a' can be displayed (or HEALTH - represents health of the battery, values corresponds to POWER_SUPPLY_HEALTH_*, defined in battery.h. +VOLTAGE_OCV - open circuit voltage of the battery. + VOLTAGE_MAX_DESIGN, VOLTAGE_MIN_DESIGN - design values for maximal and minimal power supply voltages. Maximal/minimal means values of voltages when battery considered "full"/"empty" at normal conditions. Yes, there is diff --git a/Documentation/sysctl/fs.txt b/Documentation/sysctl/fs.txt index 88fd7f5c8dcd..13d6166d7a27 100644 --- a/Documentation/sysctl/fs.txt +++ b/Documentation/sysctl/fs.txt @@ -225,6 +225,13 @@ a queue must be less or equal then msg_max. maximum message size value (it is every message queue's attribute set during its creation). +/proc/sys/fs/mqueue/msg_default is a read/write file for setting/getting the +default number of messages in a queue value if attr parameter of mq_open(2) is +NULL. If it exceed msg_max, the default value is initialized msg_max. + +/proc/sys/fs/mqueue/msgsize_default is a read/write file for setting/getting +the default message size value if attr parameter of mq_open(2) is NULL. If it +exceed msgsize_max, the default value is initialized msgsize_max. 4. /proc/sys/fs/epoll - Configuration options for the epoll interface -------------------------------------------------------- diff --git a/Documentation/trace/uprobetracer.txt b/Documentation/trace/uprobetracer.txt new file mode 100644 index 000000000000..24ce6823a09e --- /dev/null +++ b/Documentation/trace/uprobetracer.txt @@ -0,0 +1,113 @@ + Uprobe-tracer: Uprobe-based Event Tracing + ========================================= + Documentation written by Srikar Dronamraju + +Overview +-------- +Uprobe based trace events are similar to kprobe based trace events. +To enable this feature, build your kernel with CONFIG_UPROBE_EVENT=y. + +Similar to the kprobe-event tracer, this doesn't need to be activated via +current_tracer. Instead of that, add probe points via +/sys/kernel/debug/tracing/uprobe_events, and enable it via +/sys/kernel/debug/tracing/events/uprobes/<EVENT>/enabled. + +However unlike kprobe-event tracer, the uprobe event interface expects the +user to calculate the offset of the probepoint in the object + +Synopsis of uprobe_tracer +------------------------- + p[:[GRP/]EVENT] PATH:SYMBOL[+offs] [FETCHARGS] : Set a probe + + GRP : Group name. If omitted, use "uprobes" for it. + EVENT : Event name. If omitted, the event name is generated + based on SYMBOL+offs. + PATH : path to an executable or a library. + SYMBOL[+offs] : Symbol+offset where the probe is inserted. + + FETCHARGS : Arguments. Each probe can have up to 128 args. + %REG : Fetch register REG + +Event Profiling +--------------- + You can check the total number of probe hits and probe miss-hits via +/sys/kernel/debug/tracing/uprobe_profile. + The first column is event name, the second is the number of probe hits, +the third is the number of probe miss-hits. + +Usage examples +-------------- +To add a probe as a new event, write a new definition to uprobe_events +as below. + + echo 'p: /bin/bash:0x4245c0' > /sys/kernel/debug/tracing/uprobe_events + + This sets a uprobe at an offset of 0x4245c0 in the executable /bin/bash + + echo > /sys/kernel/debug/tracing/uprobe_events + + This clears all probe points. + +The following example shows how to dump the instruction pointer and %ax +a register at the probed text address. Here we are trying to probe +function zfree in /bin/zsh + + # cd /sys/kernel/debug/tracing/ + # cat /proc/`pgrep zsh`/maps | grep /bin/zsh | grep r-xp + 00400000-0048a000 r-xp 00000000 08:03 130904 /bin/zsh + # objdump -T /bin/zsh | grep -w zfree + 0000000000446420 g DF .text 0000000000000012 Base zfree + +0x46420 is the offset of zfree in object /bin/zsh that is loaded at +0x00400000. Hence the command to probe would be : + + # echo 'p /bin/zsh:0x46420 %ip %ax' > uprobe_events + +Please note: User has to explicitly calculate the offset of the probepoint +in the object. We can see the events that are registered by looking at the +uprobe_events file. + + # cat uprobe_events + p:uprobes/p_zsh_0x46420 /bin/zsh:0x00046420 arg1=%ip arg2=%ax + +The format of events can be seen by viewing the file events/uprobes/p_zsh_0x46420/format + + # cat events/uprobes/p_zsh_0x46420/format + name: p_zsh_0x46420 + ID: 922 + format: + field:unsigned short common_type; offset:0; size:2; signed:0; + field:unsigned char common_flags; offset:2; size:1; signed:0; + field:unsigned char common_preempt_count; offset:3; size:1; signed:0; + field:int common_pid; offset:4; size:4; signed:1; + field:int common_padding; offset:8; size:4; signed:1; + + field:unsigned long __probe_ip; offset:12; size:4; signed:0; + field:u32 arg1; offset:16; size:4; signed:0; + field:u32 arg2; offset:20; size:4; signed:0; + + print fmt: "(%lx) arg1=%lx arg2=%lx", REC->__probe_ip, REC->arg1, REC->arg2 + +Right after definition, each event is disabled by default. For tracing these +events, you need to enable it by: + + # echo 1 > events/uprobes/enable + +Lets disable the event after sleeping for some time. + # sleep 20 + # echo 0 > events/uprobes/enable + +And you can see the traced information via /sys/kernel/debug/tracing/trace. + + # cat trace + # tracer: nop + # + # TASK-PID CPU# TIMESTAMP FUNCTION + # | | | | | + zsh-24842 [006] 258544.995456: p_zsh_0x46420: (0x446420) arg1=446421 arg2=79 + zsh-24842 [007] 258545.000270: p_zsh_0x46420: (0x446420) arg1=446421 arg2=79 + zsh-24842 [002] 258545.043929: p_zsh_0x46420: (0x446420) arg1=446421 arg2=79 + zsh-24842 [004] 258547.046129: p_zsh_0x46420: (0x446420) arg1=446421 arg2=79 + +Each line shows us probes were triggered for a pid 24842 with ip being +0x446421 and contents of ax register being 79. diff --git a/Documentation/video4linux/4CCs.txt b/Documentation/video4linux/4CCs.txt new file mode 100644 index 000000000000..41241af1ebfe --- /dev/null +++ b/Documentation/video4linux/4CCs.txt @@ -0,0 +1,32 @@ +Guidelines for Linux4Linux pixel format 4CCs +============================================ + +Guidelines for Video4Linux 4CC codes defined using v4l2_fourcc() are +specified in this document. First of the characters defines the nature of +the pixel format, compression and colour space. The interpretation of the +other three characters depends on the first one. + +Existing 4CCs may not obey these guidelines. + +Formats +======= + +Raw bayer +--------- + +The following first characters are used by raw bayer formats: + + B: raw bayer, uncompressed + b: raw bayer, DPCM compressed + a: A-law compressed + u: u-law compressed + +2nd character: pixel order + B: BGGR + G: GBRG + g: GRBG + R: RGGB + +3rd character: uncompressed bits-per-pixel 0--9, A-- + +4th character: compressed bits-per-pixel 0--9, A-- diff --git a/Documentation/video4linux/gspca.txt b/Documentation/video4linux/gspca.txt index e6c2842407a4..1e6b6531bbcc 100644 --- a/Documentation/video4linux/gspca.txt +++ b/Documentation/video4linux/gspca.txt @@ -276,6 +276,7 @@ pac7302 093a:2622 Genius Eye 312 pac7302 093a:2624 PAC7302 pac7302 093a:2625 Genius iSlim 310 pac7302 093a:2626 Labtec 2200 +pac7302 093a:2627 Genius FaceCam 300 pac7302 093a:2628 Genius iLook 300 pac7302 093a:2629 Genious iSlim 300 pac7302 093a:262a Webcam 300k diff --git a/Documentation/video4linux/v4l2-controls.txt b/Documentation/video4linux/v4l2-controls.txt index e2492a9d1027..43da22b89728 100644 --- a/Documentation/video4linux/v4l2-controls.txt +++ b/Documentation/video4linux/v4l2-controls.txt @@ -130,8 +130,18 @@ Menu controls are added by calling v4l2_ctrl_new_std_menu: const struct v4l2_ctrl_ops *ops, u32 id, s32 max, s32 skip_mask, s32 def); +Or alternatively for integer menu controls, by calling v4l2_ctrl_new_int_menu: + + struct v4l2_ctrl *v4l2_ctrl_new_int_menu(struct v4l2_ctrl_handler *hdl, + const struct v4l2_ctrl_ops *ops, + u32 id, s32 max, s32 def, const s64 *qmenu_int); + These functions are typically called right after the v4l2_ctrl_handler_init: + static const s64 exp_bias_qmenu[] = { + -2, -1, 0, 1, 2 + }; + v4l2_ctrl_handler_init(&foo->ctrl_handler, nr_of_controls); v4l2_ctrl_new_std(&foo->ctrl_handler, &foo_ctrl_ops, V4L2_CID_BRIGHTNESS, 0, 255, 1, 128); @@ -141,6 +151,11 @@ These functions are typically called right after the v4l2_ctrl_handler_init: V4L2_CID_POWER_LINE_FREQUENCY, V4L2_CID_POWER_LINE_FREQUENCY_60HZ, 0, V4L2_CID_POWER_LINE_FREQUENCY_DISABLED); + v4l2_ctrl_new_int_menu(&foo->ctrl_handler, &foo_ctrl_ops, + V4L2_CID_EXPOSURE_BIAS, + ARRAY_SIZE(exp_bias_qmenu) - 1, + ARRAY_SIZE(exp_bias_qmenu) / 2 - 1, + exp_bias_qmenu); ... if (foo->ctrl_handler.error) { int err = foo->ctrl_handler.error; @@ -164,6 +179,12 @@ controls. There is no min argument since that is always 0 for menu controls, and instead of a step there is a skip_mask argument: if bit X is 1, then menu item X is skipped. +The v4l2_ctrl_new_int_menu function creates a new standard integer menu +control with driver-specific items in the menu. It differs from +v4l2_ctrl_new_std_menu in that it doesn't have the mask argument and takes +as the last argument an array of signed 64-bit integers that form an exact +menu item list. + Note that if something fails, the function will return NULL or an error and set ctrl_handler->error to the error code. If ctrl_handler->error was already set, then it will just return and do nothing. This is also true for diff --git a/Documentation/video4linux/v4l2-framework.txt b/Documentation/video4linux/v4l2-framework.txt index 659b2ba12a4f..1f5905270050 100644 --- a/Documentation/video4linux/v4l2-framework.txt +++ b/Documentation/video4linux/v4l2-framework.txt @@ -182,11 +182,11 @@ static int __devinit drv_probe(struct pci_dev *pdev, } If you have multiple device nodes then it can be difficult to know when it is -safe to unregister v4l2_device. For this purpose v4l2_device has refcounting -support. The refcount is increased whenever video_register_device is called and -it is decreased whenever that device node is released. When the refcount reaches -zero, then the v4l2_device release() callback is called. You can do your final -cleanup there. +safe to unregister v4l2_device for hotpluggable devices. For this purpose +v4l2_device has refcounting support. The refcount is increased whenever +video_register_device is called and it is decreased whenever that device node +is released. When the refcount reaches zero, then the v4l2_device release() +callback is called. You can do your final cleanup there. If other device nodes (e.g. ALSA) are created, then you can increase and decrease the refcount manually as well by calling: @@ -197,6 +197,10 @@ or: int v4l2_device_put(struct v4l2_device *v4l2_dev); +Since the initial refcount is 1 you also need to call v4l2_device_put in the +disconnect() callback (for USB devices) or in the remove() callback (for e.g. +PCI devices), otherwise the refcount will never reach 0. + struct v4l2_subdev ------------------ @@ -262,11 +266,16 @@ struct v4l2_subdev_video_ops { ... }; +struct v4l2_subdev_pad_ops { + ... +}; + struct v4l2_subdev_ops { const struct v4l2_subdev_core_ops *core; const struct v4l2_subdev_tuner_ops *tuner; const struct v4l2_subdev_audio_ops *audio; const struct v4l2_subdev_video_ops *video; + const struct v4l2_subdev_pad_ops *video; }; The core ops are common to all subdevs, the other categories are implemented @@ -303,6 +312,22 @@ Don't forget to cleanup the media entity before the sub-device is destroyed: media_entity_cleanup(&sd->entity); +If the subdev driver intends to process video and integrate with the media +framework, it must implement format related functionality using +v4l2_subdev_pad_ops instead of v4l2_subdev_video_ops. + +In that case, the subdev driver may set the link_validate field to provide +its own link validation function. The link validation function is called for +every link in the pipeline where both of the ends of the links are V4L2 +sub-devices. The driver is still responsible for validating the correctness +of the format configuration between sub-devices and video nodes. + +If link_validate op is not set, the default function +v4l2_subdev_link_validate_default() is used instead. This function ensures +that width, height and the media bus pixel code are equal on both source and +sink of the link. Subdev drivers are also free to use this function to +perform the checks mentioned above in addition to their own checks. + A device (bridge) driver needs to register the v4l2_subdev with the v4l2_device: @@ -555,19 +580,25 @@ allocated memory. You should also set these fields: - v4l2_dev: set to the v4l2_device parent device. + - name: set to something descriptive and unique. + - fops: set to the v4l2_file_operations struct. + - ioctl_ops: if you use the v4l2_ioctl_ops to simplify ioctl maintenance (highly recommended to use this and it might become compulsory in the future!), then set this to your v4l2_ioctl_ops struct. + - lock: leave to NULL if you want to do all the locking in the driver. - Otherwise you give it a pointer to a struct mutex_lock and before any - of the v4l2_file_operations is called this lock will be taken by the - core and released afterwards. + Otherwise you give it a pointer to a struct mutex_lock and before the + unlocked_ioctl file operation is called this lock will be taken by the + core and released afterwards. See the next section for more details. + - prio: keeps track of the priorities. Used to implement VIDIOC_G/S_PRIORITY. If left to NULL, then it will use the struct v4l2_prio_state in v4l2_device. If you want to have a separate priority state per (group of) device node(s), then you can point it to your own struct v4l2_prio_state. + - parent: you only set this if v4l2_device was registered with NULL as the parent device struct. This only happens in cases where one hardware device has multiple PCI devices that all share the same v4l2_device core. @@ -577,6 +608,7 @@ You should also set these fields: (cx8802). Since the v4l2_device cannot be associated with a particular PCI device it is setup without a parent device. But when the struct video_device is setup you do know which parent PCI device to use. + - flags: optional. Set to V4L2_FL_USE_FH_PRIO if you want to let the framework handle the VIDIOC_G/S_PRIORITY ioctls. This requires that you use struct v4l2_fh. Eventually this flag will disappear once all drivers use the core @@ -587,6 +619,16 @@ in your v4l2_file_operations struct. Do not use .ioctl! This is deprecated and will go away in the future. +In some cases you want to tell the core that a function you had specified in +your v4l2_ioctl_ops should be ignored. You can mark such ioctls by calling this +function before video_device_register is called: + +void v4l2_disable_ioctl(struct video_device *vdev, unsigned int cmd); + +This tends to be needed if based on external factors (e.g. which card is +being used) you want to turns off certain features in v4l2_ioctl_ops without +having to make a new struct. + The v4l2_file_operations struct is a subset of file_operations. The main difference is that the inode argument is omitted since it is never used. @@ -609,8 +651,22 @@ v4l2_file_operations and locking -------------------------------- You can set a pointer to a mutex_lock in struct video_device. Usually this -will be either a top-level mutex or a mutex per device node. If you want -finer-grained locking then you have to set it to NULL and do you own locking. +will be either a top-level mutex or a mutex per device node. By default this +lock will be used for unlocked_ioctl, but you can disable locking for +selected ioctls by calling: + + void v4l2_disable_ioctl_locking(struct video_device *vdev, unsigned int cmd); + +E.g.: v4l2_disable_ioctl_locking(vdev, VIDIOC_DQBUF); + +You have to call this before you register the video_device. + +Particularly with USB drivers where certain commands such as setting controls +can take a long time you may want to do your own locking for the buffer queuing +ioctls. + +If you want still finer-grained locking then you have to set mutex_lock to NULL +and do you own locking completely. It is up to the driver developer to decide which method to use. However, if your driver has high-latency operations (for example, changing the exposure @@ -618,7 +674,7 @@ of a USB webcam might take a long time), then you might be better off with doing your own locking if you want to allow the user to do other things with the device while waiting for the high-latency command to finish. -If a lock is specified then all file operations will be serialized on that +If a lock is specified then all ioctl commands will be serialized on that lock. If you use videobuf then you must pass the same lock to the videobuf queue initialize function: if videobuf has to wait for a frame to arrive, then it will temporarily unlock the lock and relock it afterwards. If your driver @@ -941,21 +997,35 @@ fast. Useful functions: -- v4l2_event_queue() +void v4l2_event_queue(struct video_device *vdev, const struct v4l2_event *ev) Queue events to video device. The driver's only responsibility is to fill in the type and the data fields. The other fields will be filled in by V4L2. -- v4l2_event_subscribe() +int v4l2_event_subscribe(struct v4l2_fh *fh, + struct v4l2_event_subscription *sub, unsigned elems, + const struct v4l2_subscribed_event_ops *ops) The video_device->ioctl_ops->vidioc_subscribe_event must check the driver is able to produce events with specified event id. Then it calls - v4l2_event_subscribe() to subscribe the event. The last argument is the - size of the event queue for this event. If it is 0, then the framework - will fill in a default value (this depends on the event type). + v4l2_event_subscribe() to subscribe the event. + + The elems argument is the size of the event queue for this event. If it is 0, + then the framework will fill in a default value (this depends on the event + type). + + The ops argument allows the driver to specify a number of callbacks: + * add: called when a new listener gets added (subscribing to the same + event twice will only cause this callback to get called once) + * del: called when a listener stops listening + * replace: replace event 'old' with event 'new'. + * merge: merge event 'old' into event 'new'. + All 4 callbacks are optional, if you don't want to specify any callbacks + the ops argument itself maybe NULL. -- v4l2_event_unsubscribe() +int v4l2_event_unsubscribe(struct v4l2_fh *fh, + struct v4l2_event_subscription *sub) vidioc_unsubscribe_event in struct v4l2_ioctl_ops. A driver may use v4l2_event_unsubscribe() directly unless it wants to be involved in @@ -964,7 +1034,7 @@ Useful functions: The special type V4L2_EVENT_ALL may be used to unsubscribe all events. The drivers may want to handle this in a special way. -- v4l2_event_pending() +int v4l2_event_pending(struct v4l2_fh *fh) Returns the number of pending events. Useful when implementing poll. diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt index 6386f8c0482e..930126698a0f 100644 --- a/Documentation/virtual/kvm/api.txt +++ b/Documentation/virtual/kvm/api.txt @@ -2,6 +2,7 @@ The Definitive KVM (Kernel-based Virtual Machine) API Documentation =================================================================== 1. General description +---------------------- The kvm API is a set of ioctls that are issued to control various aspects of a virtual machine. The ioctls belong to three classes @@ -23,7 +24,9 @@ of a virtual machine. The ioctls belong to three classes Only run vcpu ioctls from the same thread that was used to create the vcpu. + 2. File descriptors +------------------- The kvm API is centered around file descriptors. An initial open("/dev/kvm") obtains a handle to the kvm subsystem; this handle @@ -41,7 +44,9 @@ not cause harm to the host, their actual behavior is not guaranteed by the API. The only supported use is one virtual machine per process, and one vcpu per thread. + 3. Extensions +------------- As of Linux 2.6.22, the KVM ABI has been stabilized: no backward incompatible change are allowed. However, there is an extension @@ -53,7 +58,9 @@ Instead, kvm defines extension identifiers and a facility to query whether a particular extension identifier is available. If it is, a set of ioctls is available for application use. + 4. API description +------------------ This section describes ioctls that can be used to control kvm guests. For each ioctl, the following information is provided along with a @@ -75,6 +82,7 @@ description: Returns: the return value. General error numbers (EBADF, ENOMEM, EINVAL) are not detailed, but errors with specific meanings are. + 4.1 KVM_GET_API_VERSION Capability: basic @@ -90,6 +98,7 @@ supported. Applications should refuse to run if KVM_GET_API_VERSION returns a value other than 12. If this check passes, all ioctls described as 'basic' will be available. + 4.2 KVM_CREATE_VM Capability: basic @@ -109,6 +118,7 @@ In order to create user controlled virtual machines on S390, check KVM_CAP_S390_UCONTROL and use the flag KVM_VM_S390_UCONTROL as privileged user (CAP_SYS_ADMIN). + 4.3 KVM_GET_MSR_INDEX_LIST Capability: basic @@ -135,6 +145,7 @@ Note: if kvm indicates supports MCE (KVM_CAP_MCE), then the MCE bank MSRs are not returned in the MSR list, as different vcpus can have a different number of banks, as set via the KVM_X86_SETUP_MCE ioctl. + 4.4 KVM_CHECK_EXTENSION Capability: basic @@ -149,6 +160,7 @@ receives an integer that describes the extension availability. Generally 0 means no and 1 means yes, but some extensions may report additional information in the integer return value. + 4.5 KVM_GET_VCPU_MMAP_SIZE Capability: basic @@ -161,6 +173,7 @@ The KVM_RUN ioctl (cf.) communicates with userspace via a shared memory region. This ioctl returns the size of that region. See the KVM_RUN documentation for details. + 4.6 KVM_SET_MEMORY_REGION Capability: basic @@ -171,6 +184,7 @@ Returns: 0 on success, -1 on error This ioctl is obsolete and has been removed. + 4.7 KVM_CREATE_VCPU Capability: basic @@ -223,6 +237,7 @@ machines, the resulting vcpu fd can be memory mapped at page offset KVM_S390_SIE_PAGE_OFFSET in order to obtain a memory map of the virtual cpu's hardware control block. + 4.8 KVM_GET_DIRTY_LOG (vm ioctl) Capability: basic @@ -246,6 +261,7 @@ since the last call to this ioctl. Bit 0 is the first page in the memory slot. Ensure the entire structure is cleared to avoid padding issues. + 4.9 KVM_SET_MEMORY_ALIAS Capability: basic @@ -256,6 +272,7 @@ Returns: 0 (success), -1 (error) This ioctl is obsolete and has been removed. + 4.10 KVM_RUN Capability: basic @@ -272,6 +289,7 @@ obtained by mmap()ing the vcpu fd at offset 0, with the size given by KVM_GET_VCPU_MMAP_SIZE. The parameter block is formatted as a 'struct kvm_run' (see below). + 4.11 KVM_GET_REGS Capability: basic @@ -292,6 +310,7 @@ struct kvm_regs { __u64 rip, rflags; }; + 4.12 KVM_SET_REGS Capability: basic @@ -304,6 +323,7 @@ Writes the general purpose registers into the vcpu. See KVM_GET_REGS for the data structure. + 4.13 KVM_GET_SREGS Capability: basic @@ -331,6 +351,7 @@ interrupt_bitmap is a bitmap of pending external interrupts. At most one bit may be set. This interrupt has been acknowledged by the APIC but not yet injected into the cpu core. + 4.14 KVM_SET_SREGS Capability: basic @@ -342,6 +363,7 @@ Returns: 0 on success, -1 on error Writes special registers into the vcpu. See KVM_GET_SREGS for the data structures. + 4.15 KVM_TRANSLATE Capability: basic @@ -365,6 +387,7 @@ struct kvm_translation { __u8 pad[5]; }; + 4.16 KVM_INTERRUPT Capability: basic @@ -413,6 +436,7 @@ c) KVM_INTERRUPT_SET_LEVEL Note that any value for 'irq' other than the ones stated above is invalid and incurs unexpected behavior. + 4.17 KVM_DEBUG_GUEST Capability: basic @@ -423,6 +447,7 @@ Returns: -1 on error Support for this has been removed. Use KVM_SET_GUEST_DEBUG instead. + 4.18 KVM_GET_MSRS Capability: basic @@ -451,6 +476,7 @@ Application code should set the 'nmsrs' member (which indicates the size of the entries array) and the 'index' member of each array entry. kvm will fill in the 'data' member. + 4.19 KVM_SET_MSRS Capability: basic @@ -466,6 +492,7 @@ Application code should set the 'nmsrs' member (which indicates the size of the entries array), and the 'index' and 'data' members of each array entry. + 4.20 KVM_SET_CPUID Capability: basic @@ -494,6 +521,7 @@ struct kvm_cpuid { struct kvm_cpuid_entry entries[0]; }; + 4.21 KVM_SET_SIGNAL_MASK Capability: basic @@ -516,6 +544,7 @@ struct kvm_signal_mask { __u8 sigset[0]; }; + 4.22 KVM_GET_FPU Capability: basic @@ -541,6 +570,7 @@ struct kvm_fpu { __u32 pad2; }; + 4.23 KVM_SET_FPU Capability: basic @@ -566,6 +596,7 @@ struct kvm_fpu { __u32 pad2; }; + 4.24 KVM_CREATE_IRQCHIP Capability: KVM_CAP_IRQCHIP @@ -579,6 +610,7 @@ ioapic, a virtual PIC (two PICs, nested), and sets up future vcpus to have a local APIC. IRQ routing for GSIs 0-15 is set to both PIC and IOAPIC; GSI 16-23 only go to the IOAPIC. On ia64, a IOSAPIC is created. + 4.25 KVM_IRQ_LINE Capability: KVM_CAP_IRQCHIP @@ -600,6 +632,7 @@ struct kvm_irq_level { __u32 level; /* 0 or 1 */ }; + 4.26 KVM_GET_IRQCHIP Capability: KVM_CAP_IRQCHIP @@ -621,6 +654,7 @@ struct kvm_irqchip { } chip; }; + 4.27 KVM_SET_IRQCHIP Capability: KVM_CAP_IRQCHIP @@ -642,6 +676,7 @@ struct kvm_irqchip { } chip; }; + 4.28 KVM_XEN_HVM_CONFIG Capability: KVM_CAP_XEN_HVM @@ -666,6 +701,7 @@ struct kvm_xen_hvm_config { __u8 pad2[30]; }; + 4.29 KVM_GET_CLOCK Capability: KVM_CAP_ADJUST_CLOCK @@ -684,6 +720,7 @@ struct kvm_clock_data { __u32 pad[9]; }; + 4.30 KVM_SET_CLOCK Capability: KVM_CAP_ADJUST_CLOCK @@ -702,6 +739,7 @@ struct kvm_clock_data { __u32 pad[9]; }; + 4.31 KVM_GET_VCPU_EVENTS Capability: KVM_CAP_VCPU_EVENTS @@ -741,6 +779,7 @@ struct kvm_vcpu_events { KVM_VCPUEVENT_VALID_SHADOW may be set in the flags field to signal that interrupt.shadow contains a valid state. Otherwise, this field is undefined. + 4.32 KVM_SET_VCPU_EVENTS Capability: KVM_CAP_VCPU_EVENTS @@ -767,6 +806,7 @@ If KVM_CAP_INTR_SHADOW is available, KVM_VCPUEVENT_VALID_SHADOW can be set in the flags field to signal that interrupt.shadow contains a valid state and shall be written into the VCPU. + 4.33 KVM_GET_DEBUGREGS Capability: KVM_CAP_DEBUGREGS @@ -785,6 +825,7 @@ struct kvm_debugregs { __u64 reserved[9]; }; + 4.34 KVM_SET_DEBUGREGS Capability: KVM_CAP_DEBUGREGS @@ -798,6 +839,7 @@ Writes debug registers into the vcpu. See KVM_GET_DEBUGREGS for the data structure. The flags field is unused yet and must be cleared on entry. + 4.35 KVM_SET_USER_MEMORY_REGION Capability: KVM_CAP_USER_MEM @@ -844,6 +886,7 @@ It is recommended to use this API instead of the KVM_SET_MEMORY_REGION ioctl. The KVM_SET_MEMORY_REGION does not allow fine grained control over memory allocation and is deprecated. + 4.36 KVM_SET_TSS_ADDR Capability: KVM_CAP_SET_TSS_ADDR @@ -862,6 +905,7 @@ This ioctl is required on Intel-based hosts. This is needed on Intel hardware because of a quirk in the virtualization implementation (see the internals documentation when it pops into existence). + 4.37 KVM_ENABLE_CAP Capability: KVM_CAP_ENABLE_CAP @@ -897,6 +941,7 @@ function properly, this is the place to put them. __u8 pad[64]; }; + 4.38 KVM_GET_MP_STATE Capability: KVM_CAP_MP_STATE @@ -927,6 +972,7 @@ Possible values are: This ioctl is only useful after KVM_CREATE_IRQCHIP. Without an in-kernel irqchip, the multiprocessing state must be maintained by userspace. + 4.39 KVM_SET_MP_STATE Capability: KVM_CAP_MP_STATE @@ -941,6 +987,7 @@ arguments. This ioctl is only useful after KVM_CREATE_IRQCHIP. Without an in-kernel irqchip, the multiprocessing state must be maintained by userspace. + 4.40 KVM_SET_IDENTITY_MAP_ADDR Capability: KVM_CAP_SET_IDENTITY_MAP_ADDR @@ -959,6 +1006,7 @@ This ioctl is required on Intel-based hosts. This is needed on Intel hardware because of a quirk in the virtualization implementation (see the internals documentation when it pops into existence). + 4.41 KVM_SET_BOOT_CPU_ID Capability: KVM_CAP_SET_BOOT_CPU_ID @@ -971,6 +1019,7 @@ Define which vcpu is the Bootstrap Processor (BSP). Values are the same as the vcpu id in KVM_CREATE_VCPU. If this ioctl is not called, the default is vcpu 0. + 4.42 KVM_GET_XSAVE Capability: KVM_CAP_XSAVE @@ -985,6 +1034,7 @@ struct kvm_xsave { This ioctl would copy current vcpu's xsave struct to the userspace. + 4.43 KVM_SET_XSAVE Capability: KVM_CAP_XSAVE @@ -999,6 +1049,7 @@ struct kvm_xsave { This ioctl would copy userspace's xsave struct to the kernel. + 4.44 KVM_GET_XCRS Capability: KVM_CAP_XCRS @@ -1022,6 +1073,7 @@ struct kvm_xcrs { This ioctl would copy current vcpu's xcrs to the userspace. + 4.45 KVM_SET_XCRS Capability: KVM_CAP_XCRS @@ -1045,6 +1097,7 @@ struct kvm_xcrs { This ioctl would set vcpu's xcr to the value userspace specified. + 4.46 KVM_GET_SUPPORTED_CPUID Capability: KVM_CAP_EXT_CPUID @@ -1119,6 +1172,7 @@ support. Instead it is reported via if that returns true and you use KVM_CREATE_IRQCHIP, or if you emulate the feature in userspace, then you can enable the feature for KVM_SET_CPUID2. + 4.47 KVM_PPC_GET_PVINFO Capability: KVM_CAP_PPC_GET_PVINFO @@ -1142,6 +1196,7 @@ of 4 instructions that make up a hypercall. If any additional field gets added to this structure later on, a bit for that additional piece of information will be set in the flags bitmap. + 4.48 KVM_ASSIGN_PCI_DEVICE Capability: KVM_CAP_DEVICE_ASSIGNMENT @@ -1185,6 +1240,7 @@ Only PCI header type 0 devices with PCI BAR resources are supported by device assignment. The user requesting this ioctl must have read/write access to the PCI sysfs resource files associated with the device. + 4.49 KVM_DEASSIGN_PCI_DEVICE Capability: KVM_CAP_DEVICE_DEASSIGNMENT @@ -1198,6 +1254,7 @@ Ends PCI device assignment, releasing all associated resources. See KVM_CAP_DEVICE_ASSIGNMENT for the data structure. Only assigned_dev_id is used in kvm_assigned_pci_dev to identify the device. + 4.50 KVM_ASSIGN_DEV_IRQ Capability: KVM_CAP_ASSIGN_DEV_IRQ @@ -1231,6 +1288,7 @@ The following flags are defined: It is not valid to specify multiple types per host or guest IRQ. However, the IRQ type of host and guest can differ or can even be null. + 4.51 KVM_DEASSIGN_DEV_IRQ Capability: KVM_CAP_ASSIGN_DEV_IRQ @@ -1245,6 +1303,7 @@ See KVM_ASSIGN_DEV_IRQ for the data structure. The target device is specified by assigned_dev_id, flags must correspond to the IRQ type specified on KVM_ASSIGN_DEV_IRQ. Partial deassignment of host or guest IRQ is allowed. + 4.52 KVM_SET_GSI_ROUTING Capability: KVM_CAP_IRQ_ROUTING @@ -1293,6 +1352,7 @@ struct kvm_irq_routing_msi { __u32 pad; }; + 4.53 KVM_ASSIGN_SET_MSIX_NR Capability: KVM_CAP_DEVICE_MSIX @@ -1314,6 +1374,7 @@ struct kvm_assigned_msix_nr { #define KVM_MAX_MSIX_PER_DEV 256 + 4.54 KVM_ASSIGN_SET_MSIX_ENTRY Capability: KVM_CAP_DEVICE_MSIX @@ -1332,7 +1393,8 @@ struct kvm_assigned_msix_entry { __u16 padding[3]; }; -4.54 KVM_SET_TSC_KHZ + +4.55 KVM_SET_TSC_KHZ Capability: KVM_CAP_TSC_CONTROL Architectures: x86 @@ -1343,7 +1405,8 @@ Returns: 0 on success, -1 on error Specifies the tsc frequency for the virtual machine. The unit of the frequency is KHz. -4.55 KVM_GET_TSC_KHZ + +4.56 KVM_GET_TSC_KHZ Capability: KVM_CAP_GET_TSC_KHZ Architectures: x86 @@ -1355,7 +1418,8 @@ Returns the tsc frequency of the guest. The unit of the return value is KHz. If the host has unstable tsc this ioctl returns -EIO instead as an error. -4.56 KVM_GET_LAPIC + +4.57 KVM_GET_LAPIC Capability: KVM_CAP_IRQCHIP Architectures: x86 @@ -1371,7 +1435,8 @@ struct kvm_lapic_state { Reads the Local APIC registers and copies them into the input argument. The data format and layout are the same as documented in the architecture manual. -4.57 KVM_SET_LAPIC + +4.58 KVM_SET_LAPIC Capability: KVM_CAP_IRQCHIP Architectures: x86 @@ -1387,7 +1452,8 @@ struct kvm_lapic_state { Copies the input argument into the the Local APIC registers. The data format and layout are the same as documented in the architecture manual. -4.58 KVM_IOEVENTFD + +4.59 KVM_IOEVENTFD Capability: KVM_CAP_IOEVENTFD Architectures: all @@ -1417,7 +1483,8 @@ The following flags are defined: If datamatch flag is set, the event will be signaled only if the written value to the registered address is equal to datamatch in struct kvm_ioeventfd. -4.59 KVM_DIRTY_TLB + +4.60 KVM_DIRTY_TLB Capability: KVM_CAP_SW_TLB Architectures: ppc @@ -1449,7 +1516,8 @@ The "num_dirty" field is a performance hint for KVM to determine whether it should skip processing the bitmap and just invalidate everything. It must be set to the number of set bits in the bitmap. -4.60 KVM_ASSIGN_SET_INTX_MASK + +4.61 KVM_ASSIGN_SET_INTX_MASK Capability: KVM_CAP_PCI_2_3 Architectures: x86 @@ -1482,6 +1550,7 @@ See KVM_ASSIGN_DEV_IRQ for the data structure. The target device is specified by assigned_dev_id. In the flags field, only KVM_DEV_ASSIGN_MASK_INTX is evaluated. + 4.62 KVM_CREATE_SPAPR_TCE Capability: KVM_CAP_SPAPR_TCE @@ -1517,6 +1586,7 @@ the entries written by kernel-handled H_PUT_TCE calls, and also lets userspace update the TCE table directly which is useful in some circumstances. + 4.63 KVM_ALLOCATE_RMA Capability: KVM_CAP_PPC_RMA @@ -1549,6 +1619,7 @@ is supported; 2 if the processor requires all virtual machines to have an RMA, or 1 if the processor can use an RMA but doesn't require it, because it supports the Virtual RMA (VRMA) facility. + 4.64 KVM_NMI Capability: KVM_CAP_USER_NMI @@ -1574,6 +1645,7 @@ following algorithm: Some guests configure the LINT1 NMI input to cause a panic, aiding in debugging. + 4.65 KVM_S390_UCAS_MAP Capability: KVM_CAP_S390_UCONTROL @@ -1593,6 +1665,7 @@ This ioctl maps the memory at "user_addr" with the length "length" to the vcpu's address space starting at "vcpu_addr". All parameters need to be alligned by 1 megabyte. + 4.66 KVM_S390_UCAS_UNMAP Capability: KVM_CAP_S390_UCONTROL @@ -1612,6 +1685,7 @@ This ioctl unmaps the memory in the vcpu's address space starting at "vcpu_addr" with the length "length". The field "user_addr" is ignored. All parameters need to be alligned by 1 megabyte. + 4.67 KVM_S390_VCPU_FAULT Capability: KVM_CAP_S390_UCONTROL @@ -1628,6 +1702,7 @@ table upfront. This is useful to handle validity intercepts for user controlled virtual machines to fault in the virtual cpu's lowcore pages prior to calling the KVM_RUN ioctl. + 4.68 KVM_SET_ONE_REG Capability: KVM_CAP_ONE_REG @@ -1653,6 +1728,7 @@ registers, find a list below: | | PPC | KVM_REG_PPC_HIOR | 64 + 4.69 KVM_GET_ONE_REG Capability: KVM_CAP_ONE_REG @@ -1669,7 +1745,193 @@ at the memory location pointed to by "addr". The list of registers accessible using this interface is identical to the list in 4.64. + +4.70 KVM_KVMCLOCK_CTRL + +Capability: KVM_CAP_KVMCLOCK_CTRL +Architectures: Any that implement pvclocks (currently x86 only) +Type: vcpu ioctl +Parameters: None +Returns: 0 on success, -1 on error + +This signals to the host kernel that the specified guest is being paused by +userspace. The host will set a flag in the pvclock structure that is checked +from the soft lockup watchdog. The flag is part of the pvclock structure that +is shared between guest and host, specifically the second bit of the flags +field of the pvclock_vcpu_time_info structure. It will be set exclusively by +the host and read/cleared exclusively by the guest. The guest operation of +checking and clearing the flag must an atomic operation so +load-link/store-conditional, or equivalent must be used. There are two cases +where the guest will clear the flag: when the soft lockup watchdog timer resets +itself or when a soft lockup is detected. This ioctl can be called any time +after pausing the vcpu, but before it is resumed. + + +4.71 KVM_SIGNAL_MSI + +Capability: KVM_CAP_SIGNAL_MSI +Architectures: x86 +Type: vm ioctl +Parameters: struct kvm_msi (in) +Returns: >0 on delivery, 0 if guest blocked the MSI, and -1 on error + +Directly inject a MSI message. Only valid with in-kernel irqchip that handles +MSI messages. + +struct kvm_msi { + __u32 address_lo; + __u32 address_hi; + __u32 data; + __u32 flags; + __u8 pad[16]; +}; + +No flags are defined so far. The corresponding field must be 0. + + +4.71 KVM_CREATE_PIT2 + +Capability: KVM_CAP_PIT2 +Architectures: x86 +Type: vm ioctl +Parameters: struct kvm_pit_config (in) +Returns: 0 on success, -1 on error + +Creates an in-kernel device model for the i8254 PIT. This call is only valid +after enabling in-kernel irqchip support via KVM_CREATE_IRQCHIP. The following +parameters have to be passed: + +struct kvm_pit_config { + __u32 flags; + __u32 pad[15]; +}; + +Valid flags are: + +#define KVM_PIT_SPEAKER_DUMMY 1 /* emulate speaker port stub */ + +PIT timer interrupts may use a per-VM kernel thread for injection. If it +exists, this thread will have a name of the following pattern: + +kvm-pit/<owner-process-pid> + +When running a guest with elevated priorities, the scheduling parameters of +this thread may have to be adjusted accordingly. + +This IOCTL replaces the obsolete KVM_CREATE_PIT. + + +4.72 KVM_GET_PIT2 + +Capability: KVM_CAP_PIT_STATE2 +Architectures: x86 +Type: vm ioctl +Parameters: struct kvm_pit_state2 (out) +Returns: 0 on success, -1 on error + +Retrieves the state of the in-kernel PIT model. Only valid after +KVM_CREATE_PIT2. The state is returned in the following structure: + +struct kvm_pit_state2 { + struct kvm_pit_channel_state channels[3]; + __u32 flags; + __u32 reserved[9]; +}; + +Valid flags are: + +/* disable PIT in HPET legacy mode */ +#define KVM_PIT_FLAGS_HPET_LEGACY 0x00000001 + +This IOCTL replaces the obsolete KVM_GET_PIT. + + +4.73 KVM_SET_PIT2 + +Capability: KVM_CAP_PIT_STATE2 +Architectures: x86 +Type: vm ioctl +Parameters: struct kvm_pit_state2 (in) +Returns: 0 on success, -1 on error + +Sets the state of the in-kernel PIT model. Only valid after KVM_CREATE_PIT2. +See KVM_GET_PIT2 for details on struct kvm_pit_state2. + +This IOCTL replaces the obsolete KVM_SET_PIT. + + +4.74 KVM_PPC_GET_SMMU_INFO + +Capability: KVM_CAP_PPC_GET_SMMU_INFO +Architectures: powerpc +Type: vm ioctl +Parameters: None +Returns: 0 on success, -1 on error + +This populates and returns a structure describing the features of +the "Server" class MMU emulation supported by KVM. +This can in turn be used by userspace to generate the appropariate +device-tree properties for the guest operating system. + +The structure contains some global informations, followed by an +array of supported segment page sizes: + + struct kvm_ppc_smmu_info { + __u64 flags; + __u32 slb_size; + __u32 pad; + struct kvm_ppc_one_seg_page_size sps[KVM_PPC_PAGE_SIZES_MAX_SZ]; + }; + +The supported flags are: + + - KVM_PPC_PAGE_SIZES_REAL: + When that flag is set, guest page sizes must "fit" the backing + store page sizes. When not set, any page size in the list can + be used regardless of how they are backed by userspace. + + - KVM_PPC_1T_SEGMENTS + The emulated MMU supports 1T segments in addition to the + standard 256M ones. + +The "slb_size" field indicates how many SLB entries are supported + +The "sps" array contains 8 entries indicating the supported base +page sizes for a segment in increasing order. Each entry is defined +as follow: + + struct kvm_ppc_one_seg_page_size { + __u32 page_shift; /* Base page shift of segment (or 0) */ + __u32 slb_enc; /* SLB encoding for BookS */ + struct kvm_ppc_one_page_size enc[KVM_PPC_PAGE_SIZES_MAX_SZ]; + }; + +An entry with a "page_shift" of 0 is unused. Because the array is +organized in increasing order, a lookup can stop when encoutering +such an entry. + +The "slb_enc" field provides the encoding to use in the SLB for the +page size. The bits are in positions such as the value can directly +be OR'ed into the "vsid" argument of the slbmte instruction. + +The "enc" array is a list which for each of those segment base page +size provides the list of supported actual page sizes (which can be +only larger or equal to the base page size), along with the +corresponding encoding in the hash PTE. Similarily, the array is +8 entries sorted by increasing sizes and an entry with a "0" shift +is an empty entry and a terminator: + + struct kvm_ppc_one_page_size { + __u32 page_shift; /* Page shift (or 0) */ + __u32 pte_enc; /* Encoding in the HPTE (>>12) */ + }; + +The "pte_enc" field provides a value that can OR'ed into the hash +PTE's RPN field (ie, it needs to be shifted left by 12 to OR it +into the hash PTE second double word). + 5. The kvm_run structure +------------------------ Application code obtains a pointer to the kvm_run structure by mmap()ing a vcpu fd. From that point, application code can control @@ -1910,7 +2172,9 @@ and usually define the validity of a groups of registers. (e.g. one bit }; + 6. Capabilities that can be enabled +----------------------------------- There are certain capabilities that change the behavior of the virtual CPU when enabled. To enable them, please see section 4.37. Below you can find a list of @@ -1926,6 +2190,7 @@ The following information is provided along with the description: Returns: the return value. General error numbers (EBADF, ENOMEM, EINVAL) are not detailed, but errors with specific meanings are. + 6.1 KVM_CAP_PPC_OSI Architectures: ppc @@ -1939,6 +2204,7 @@ between the guest and the host. When this capability is enabled, KVM_EXIT_OSI can occur. + 6.2 KVM_CAP_PPC_PAPR Architectures: ppc @@ -1957,6 +2223,7 @@ HTAB invisible to the guest. When this capability is enabled, KVM_EXIT_PAPR_HCALL can occur. + 6.3 KVM_CAP_SW_TLB Architectures: ppc diff --git a/Documentation/virtual/kvm/cpuid.txt b/Documentation/virtual/kvm/cpuid.txt index 882068538c9c..83afe65d4966 100644 --- a/Documentation/virtual/kvm/cpuid.txt +++ b/Documentation/virtual/kvm/cpuid.txt @@ -10,11 +10,15 @@ a guest. KVM cpuid functions are: function: KVM_CPUID_SIGNATURE (0x40000000) -returns : eax = 0, +returns : eax = 0x40000001, ebx = 0x4b4d564b, ecx = 0x564b4d56, edx = 0x4d. Note that this value in ebx, ecx and edx corresponds to the string "KVMKVMKVM". +The value in eax corresponds to the maximum cpuid function present in this leaf, +and will be updated if more functions are added in the future. +Note also that old hosts set eax value to 0x0. This should +be interpreted as if the value was 0x40000001. This function queries the presence of KVM cpuid leafs. diff --git a/Documentation/virtual/kvm/msr.txt b/Documentation/virtual/kvm/msr.txt index 50317809113d..96b41bd97523 100644 --- a/Documentation/virtual/kvm/msr.txt +++ b/Documentation/virtual/kvm/msr.txt @@ -109,6 +109,10 @@ MSR_KVM_SYSTEM_TIME_NEW: 0x4b564d01 0 | 24 | multiple cpus are guaranteed to | | be monotonic ------------------------------------------------------------- + | | guest vcpu has been paused by + 1 | N/A | the host + | | See 4.70 in api.txt + ------------------------------------------------------------- Availability of this MSR must be checked via bit 3 in 0x4000001 cpuid leaf prior to usage. diff --git a/Documentation/vm/pagemap.txt b/Documentation/vm/pagemap.txt index 4600cbe3d6be..7587493c67f1 100644 --- a/Documentation/vm/pagemap.txt +++ b/Documentation/vm/pagemap.txt @@ -16,7 +16,7 @@ There are three components to pagemap: * Bits 0-4 swap type if swapped * Bits 5-54 swap offset if swapped * Bits 55-60 page shift (page size = 1<<page shift) - * Bit 61 reserved for future use + * Bit 61 page is file-page or shared-anon * Bit 62 page swapped * Bit 63 page present diff --git a/Documentation/vm/transhuge.txt b/Documentation/vm/transhuge.txt index 29bdf62aac09..f734bb2a78dc 100644 --- a/Documentation/vm/transhuge.txt +++ b/Documentation/vm/transhuge.txt @@ -166,6 +166,68 @@ behavior. So to make them effective you need to restart any application that could have been using hugepages. This also applies to the regions registered in khugepaged. +== Monitoring usage == + +The number of transparent huge pages currently used by the system is +available by reading the AnonHugePages field in /proc/meminfo. To +identify what applications are using transparent huge pages, it is +necessary to read /proc/PID/smaps and count the AnonHugePages fields +for each mapping. Note that reading the smaps file is expensive and +reading it frequently will incur overhead. + +There are a number of counters in /proc/vmstat that may be used to +monitor how successfully the system is providing huge pages for use. + +thp_fault_alloc is incremented every time a huge page is successfully + allocated to handle a page fault. This applies to both the + first time a page is faulted and for COW faults. + +thp_collapse_alloc is incremented by khugepaged when it has found + a range of pages to collapse into one huge page and has + successfully allocated a new huge page to store the data. + +thp_fault_fallback is incremented if a page fault fails to allocate + a huge page and instead falls back to using small pages. + +thp_collapse_alloc_failed is incremented if khugepaged found a range + of pages that should be collapsed into one huge page but failed + the allocation. + +thp_split is incremented every time a huge page is split into base + pages. This can happen for a variety of reasons but a common + reason is that a huge page is old and is being reclaimed. + +As the system ages, allocating huge pages may be expensive as the +system uses memory compaction to copy data around memory to free a +huge page for use. There are some counters in /proc/vmstat to help +monitor this overhead. + +compact_stall is incremented every time a process stalls to run + memory compaction so that a huge page is free for use. + +compact_success is incremented if the system compacted memory and + freed a huge page for use. + +compact_fail is incremented if the system tries to compact memory + but failed. + +compact_pages_moved is incremented each time a page is moved. If + this value is increasing rapidly, it implies that the system + is copying a lot of data to satisfy the huge page allocation. + It is possible that the cost of copying exceeds any savings + from reduced TLB misses. + +compact_pagemigrate_failed is incremented when the underlying mechanism + for moving a page failed. + +compact_blocks_moved is incremented each time memory compaction examines + a huge page aligned range of pages. + +It is possible to establish how long the stalls were using the function +tracer to record how long was spent in __alloc_pages_nodemask and +using the mm_page_alloc tracepoint to identify which allocations were +for huge pages. + == get_user_pages and follow_page == get_user_pages and follow_page if run on a hugepage, will return the diff --git a/Documentation/watchdog/watchdog-kernel-api.txt b/Documentation/watchdog/watchdog-kernel-api.txt index 25fe4304f2fc..086638f6c82d 100644 --- a/Documentation/watchdog/watchdog-kernel-api.txt +++ b/Documentation/watchdog/watchdog-kernel-api.txt @@ -1,6 +1,6 @@ The Linux WatchDog Timer Driver Core kernel API. =============================================== -Last reviewed: 16-Mar-2012 +Last reviewed: 22-May-2012 Wim Van Sebroeck <wim@iguana.be> @@ -39,6 +39,10 @@ watchdog_device structure. The watchdog device structure looks like this: struct watchdog_device { + int id; + struct cdev cdev; + struct device *dev; + struct device *parent; const struct watchdog_info *info; const struct watchdog_ops *ops; unsigned int bootstatus; @@ -46,10 +50,20 @@ struct watchdog_device { unsigned int min_timeout; unsigned int max_timeout; void *driver_data; + struct mutex lock; unsigned long status; }; It contains following fields: +* id: set by watchdog_register_device, id 0 is special. It has both a + /dev/watchdog0 cdev (dynamic major, minor 0) as well as the old + /dev/watchdog miscdev. The id is set automatically when calling + watchdog_register_device. +* cdev: cdev for the dynamic /dev/watchdog<id> device nodes. This + field is also populated by watchdog_register_device. +* dev: device under the watchdog class (created by watchdog_register_device). +* parent: set this to the parent device (or NULL) before calling + watchdog_register_device. * info: a pointer to a watchdog_info structure. This structure gives some additional information about the watchdog timer itself. (Like it's unique name) * ops: a pointer to the list of watchdog operations that the watchdog supports. @@ -61,6 +75,7 @@ It contains following fields: * driver_data: a pointer to the drivers private data of a watchdog device. This data should only be accessed via the watchdog_set_drvdata and watchdog_get_drvdata routines. +* lock: Mutex for WatchDog Timer Driver Core internal use only. * status: this field contains a number of status bits that give extra information about the status of the device (Like: is the watchdog timer running/active, is the nowayout bit set, is the device opened via @@ -78,6 +93,8 @@ struct watchdog_ops { unsigned int (*status)(struct watchdog_device *); int (*set_timeout)(struct watchdog_device *, unsigned int); unsigned int (*get_timeleft)(struct watchdog_device *); + void (*ref)(struct watchdog_device *); + void (*unref)(struct watchdog_device *); long (*ioctl)(struct watchdog_device *, unsigned int, unsigned long); }; @@ -85,6 +102,21 @@ It is important that you first define the module owner of the watchdog timer driver's operations. This module owner will be used to lock the module when the watchdog is active. (This to avoid a system crash when you unload the module and /dev/watchdog is still open). + +If the watchdog_device struct is dynamically allocated, just locking the module +is not enough and a driver also needs to define the ref and unref operations to +ensure the structure holding the watchdog_device does not go away. + +The simplest (and usually sufficient) implementation of this is to: +1) Add a kref struct to the same structure which is holding the watchdog_device +2) Define a release callback for the kref which frees the struct holding both +3) Call kref_init on this kref *before* calling watchdog_register_device() +4) Define a ref operation calling kref_get on this kref +5) Define a unref operation calling kref_put on this kref +6) When it is time to cleanup: + * Do not kfree() the struct holding both, the last kref_put will do this! + * *After* calling watchdog_unregister_device() call kref_put on the kref + Some operations are mandatory and some are optional. The mandatory operations are: * start: this is a pointer to the routine that starts the watchdog timer @@ -125,6 +157,10 @@ they are supported. These optional routines/operations are: (Note: the WDIOF_SETTIMEOUT needs to be set in the options field of the watchdog's info structure). * get_timeleft: this routines returns the time that's left before a reset. +* ref: the operation that calls kref_get on the kref of a dynamically + allocated watchdog_device struct. +* unref: the operation that calls kref_put on the kref of a dynamically + allocated watchdog_device struct. * ioctl: if this routine is present then it will be called first before we do our own internal ioctl call handling. This routine should return -ENOIOCTLCMD if a command is not supported. The parameters that are passed to the ioctl @@ -144,6 +180,11 @@ bit-operations. The status bits that are defined are: (This bit should only be used by the WatchDog Timer Driver Core). * WDOG_NO_WAY_OUT: this bit stores the nowayout setting for the watchdog. If this bit is set then the watchdog timer will not be able to stop. +* WDOG_UNREGISTERED: this bit gets set by the WatchDog Timer Driver Core + after calling watchdog_unregister_device, and then checked before calling + any watchdog_ops, so that you can be sure that no operations (other then + unref) will get called after unregister, even if userspace still holds a + reference to /dev/watchdog To set the WDOG_NO_WAY_OUT status bit (before registering your watchdog timer device) you can either: diff --git a/Documentation/watchdog/watchdog-parameters.txt b/Documentation/watchdog/watchdog-parameters.txt index 17ddd822b456..04fddbacdbde 100644 --- a/Documentation/watchdog/watchdog-parameters.txt +++ b/Documentation/watchdog/watchdog-parameters.txt @@ -78,6 +78,11 @@ wd0_timeout: Default watchdog0 timeout in 1/10secs wd1_timeout: Default watchdog1 timeout in 1/10secs wd2_timeout: Default watchdog2 timeout in 1/10secs ------------------------------------------------- +da9052wdt: +timeout: Watchdog timeout in seconds. 2<= timeout <=131, default=2.048s +nowayout: Watchdog cannot be stopped once started + (default=kernel config parameter) +------------------------------------------------- davinci_wdt: heartbeat: Watchdog heartbeat period in seconds from 1 to 600, default 60 ------------------------------------------------- |
