diff options
Diffstat (limited to 'Documentation')
44 files changed, 1058 insertions, 121 deletions
diff --git a/Documentation/ABI/stable/sysfs-driver-ib_srp b/Documentation/ABI/stable/sysfs-driver-ib_srp index 5c53d28f775c..b9688de8455b 100644 --- a/Documentation/ABI/stable/sysfs-driver-ib_srp +++ b/Documentation/ABI/stable/sysfs-driver-ib_srp @@ -61,6 +61,12 @@ Description: Interface for making ib_srp connect to a new target. interrupt is handled by a different CPU then the comp_vector parameter can be used to spread the SRP completion workload over multiple CPU's. + * tl_retry_count, a number in the range 2..7 specifying the + IB RC retry count. + * queue_size, the maximum number of commands that the + initiator is allowed to queue per SCSI host. The default + value for this parameter is 62. The lowest supported value + is 2. What: /sys/class/infiniband_srp/srp-<hca>-<port_number>/ibdev Date: January 2, 2006 @@ -153,6 +159,13 @@ Contact: linux-rdma@vger.kernel.org Description: InfiniBand service ID used for establishing communication with the SRP target. +What: /sys/class/scsi_host/host<n>/sgid +Date: February 1, 2014 +KernelVersion: 3.13 +Contact: linux-rdma@vger.kernel.org +Description: InfiniBand GID of the source port used for communication with + the SRP target. + What: /sys/class/scsi_host/host<n>/zero_req_lim Date: September 20, 2006 KernelVersion: 2.6.18 diff --git a/Documentation/ABI/stable/sysfs-transport-srp b/Documentation/ABI/stable/sysfs-transport-srp index b36fb0dc13c8..ec7af69fea0a 100644 --- a/Documentation/ABI/stable/sysfs-transport-srp +++ b/Documentation/ABI/stable/sysfs-transport-srp @@ -5,6 +5,24 @@ Contact: linux-scsi@vger.kernel.org, linux-rdma@vger.kernel.org Description: Instructs an SRP initiator to disconnect from a target and to remove all LUNs imported from that target. +What: /sys/class/srp_remote_ports/port-<h>:<n>/dev_loss_tmo +Date: February 1, 2014 +KernelVersion: 3.13 +Contact: linux-scsi@vger.kernel.org, linux-rdma@vger.kernel.org +Description: Number of seconds the SCSI layer will wait after a transport + layer error has been observed before removing a target port. + Zero means immediate removal. Setting this attribute to "off" + will disable the dev_loss timer. + +What: /sys/class/srp_remote_ports/port-<h>:<n>/fast_io_fail_tmo +Date: February 1, 2014 +KernelVersion: 3.13 +Contact: linux-scsi@vger.kernel.org, linux-rdma@vger.kernel.org +Description: Number of seconds the SCSI layer will wait after a transport + layer error has been observed before failing I/O. Zero means + failing I/O immediately. Setting this attribute to "off" will + disable the fast_io_fail timer. + What: /sys/class/srp_remote_ports/port-<h>:<n>/port_id Date: June 27, 2007 KernelVersion: 2.6.24 @@ -12,8 +30,29 @@ Contact: linux-scsi@vger.kernel.org Description: 16-byte local SRP port identifier in hexadecimal format. An example: 4c:49:4e:55:58:20:56:49:4f:00:00:00:00:00:00:00. +What: /sys/class/srp_remote_ports/port-<h>:<n>/reconnect_delay +Date: February 1, 2014 +KernelVersion: 3.13 +Contact: linux-scsi@vger.kernel.org, linux-rdma@vger.kernel.org +Description: Number of seconds the SCSI layer will wait after a reconnect + attempt failed before retrying. Setting this attribute to + "off" will disable time-based reconnecting. + What: /sys/class/srp_remote_ports/port-<h>:<n>/roles Date: June 27, 2007 KernelVersion: 2.6.24 Contact: linux-scsi@vger.kernel.org Description: Role of the remote port. Either "SRP Initiator" or "SRP Target". + +What: /sys/class/srp_remote_ports/port-<h>:<n>/state +Date: February 1, 2014 +KernelVersion: 3.13 +Contact: linux-scsi@vger.kernel.org, linux-rdma@vger.kernel.org +Description: State of the transport layer used for communication with the + remote port. "running" if the transport layer is operational; + "blocked" if a transport layer error has been encountered but + the fast_io_fail_tmo timer has not yet fired; "fail-fast" + after the fast_io_fail_tmo timer has fired and before the + "dev_loss_tmo" timer has fired; "lost" after the + "dev_loss_tmo" timer has fired and before the port is finally + removed. diff --git a/Documentation/ABI/testing/sysfs-driver-hid-roccat-ryos b/Documentation/ABI/testing/sysfs-driver-hid-roccat-ryos new file mode 100644 index 000000000000..1d6a8cf9dc0a --- /dev/null +++ b/Documentation/ABI/testing/sysfs-driver-hid-roccat-ryos @@ -0,0 +1,178 @@ +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/control +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one select which data from which + profile will be read next. The data has to be 3 bytes long. + This file is writeonly. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/profile +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: The mouse can store 5 profiles which can be switched by the + press of a button. profile holds index of actual profile. + This value is persistent, so its value determines the profile + that's active when the device is powered on next time. + When written, the device activates the set profile immediately. + The data has to be 3 bytes long. + The device will reject invalid data. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/keys_primary +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set the default of all keys for + a specific profile. Profile index is included in written data. + The data has to be 125 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/keys_function +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set the function of the + function keys for a specific profile. Profile index is included + in written data. The data has to be 95 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/keys_macro +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set the function of the macro + keys for a specific profile. Profile index is included in + written data. The data has to be 35 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/keys_thumbster +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set the function of the + thumbster keys for a specific profile. Profile index is included + in written data. The data has to be 23 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/keys_extra +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set the function of the + capslock and function keys for a specific profile. Profile index + is included in written data. The data has to be 8 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/keys_easyzone +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set the function of the + easyzone keys for a specific profile. Profile index is included + in written data. The data has to be 294 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/key_mask +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one deactivate certain keys like + windows and application keys, to prevent accidental presses. + Profile index for which this settings occur is included in + written data. The data has to be 6 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/light +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set the backlight intensity for + a specific profile. Profile index is included in written data. + This attribute is only valid for the glow and pro variant. + The data has to be 16 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/macro +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one store macros with max 480 + keystrokes for a specific button for a specific profile. + Button and profile indexes are included in written data. + The data has to be 2002 bytes long. + Before reading this file, control has to be written to select + which profile and key to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/info +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When read, this file returns general data like firmware version. + The data is 8 bytes long. + This file is readonly. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/reset +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one reset the device. + The data has to be 3 bytes long. + This file is writeonly. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/talk +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one trigger easyshift functionality + from the host. + The data has to be 16 bytes long. + This file is writeonly. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/light_control +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one switch between stored and custom + light settings. + This attribute is only valid for the pro variant. + The data has to be 8 bytes long. + This file is writeonly. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/stored_lights +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set per-key lighting for different + layers. + This attribute is only valid for the pro variant. + The data has to be 1382 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/custom_lights +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set the actual per-key lighting. + This attribute is only valid for the pro variant. + The data has to be 20 bytes long. + This file is writeonly. +Users: http://roccat.sourceforge.net + +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/ryos/roccatryos<minor>/light_macro +Date: October 2013 +Contact: Stefan Achatz <erazor_de@users.sourceforge.net> +Description: When written, this file lets one set a light macro that is looped + whenever the device gets in dimness mode. + This attribute is only valid for the pro variant. + The data has to be 2002 bytes long. + Before reading this file, control has to be written to select + which profile to read. +Users: http://roccat.sourceforge.net diff --git a/Documentation/ABI/testing/sysfs-driver-hid-wiimote b/Documentation/ABI/testing/sysfs-driver-hid-wiimote index ed5dd567d397..39dfa5cb1cc5 100644 --- a/Documentation/ABI/testing/sysfs-driver-hid-wiimote +++ b/Documentation/ABI/testing/sysfs-driver-hid-wiimote @@ -57,3 +57,21 @@ Description: This attribute is only provided if the device was detected as a Calibration data is already applied by the kernel to all input values but may be used by user-space to perform other transformations. + +What: /sys/bus/hid/drivers/wiimote/<dev>/pro_calib +Date: October 2013 +KernelVersion: 3.13 +Contact: David Herrmann <dh.herrmann@gmail.com> +Description: This attribute is only provided if the device was detected as a + pro-controller. It provides a single line with 4 calibration + values for all 4 analog sticks. Format is: "x1:y1 x2:y2". Data + is prefixed with a +/-. Each value is a signed 16bit number. + Data is encoded as decimal numbers and specifies the offsets of + the analog sticks of the pro-controller. + Calibration data is already applied by the kernel to all input + values but may be used by user-space to perform other + transformations. + Calibration data is detected by the kernel during device setup. + You can write "scan\n" into this file to re-trigger calibration. + You can also write data directly in the form "x1:y1 x2:y2" to + set the calibration values manually. diff --git a/Documentation/DMA-attributes.txt b/Documentation/DMA-attributes.txt index e59480db9ee0..cc2450d80310 100644 --- a/Documentation/DMA-attributes.txt +++ b/Documentation/DMA-attributes.txt @@ -13,7 +13,7 @@ all pending DMA writes to complete, and thus provides a mechanism to strictly order DMA from a device across all intervening busses and bridges. This barrier is not specific to a particular type of interconnect, it applies to the system as a whole, and so its -implementation must account for the idiosyncracies of the system all +implementation must account for the idiosyncrasies of the system all the way from the DMA device to memory. As an example of a situation where DMA_ATTR_WRITE_BARRIER would be @@ -60,7 +60,7 @@ such mapping is non-trivial task and consumes very limited resources Buffers allocated with this attribute can be only passed to user space by calling dma_mmap_attrs(). By using this API, you are guaranteeing that you won't dereference the pointer returned by dma_alloc_attr(). You -can threat it as a cookie that must be passed to dma_mmap_attrs() and +can treat it as a cookie that must be passed to dma_mmap_attrs() and dma_free_attrs(). Make sure that both of these also get this attribute set on each call. @@ -82,7 +82,7 @@ to 'device' domain, what synchronizes CPU caches for the given region (usually it means that the cache has been flushed or invalidated depending on the dma direction). However, next calls to dma_map_{single,page,sg}() for other devices will perform exactly the -same sychronization operation on the CPU cache. CPU cache sychronization +same synchronization operation on the CPU cache. CPU cache synchronization might be a time consuming operation, especially if the buffers are large, so it is highly recommended to avoid it if possible. DMA_ATTR_SKIP_CPU_SYNC allows platform code to skip synchronization of diff --git a/Documentation/devicetree/bindings/arc/pmu.txt b/Documentation/devicetree/bindings/arc/pmu.txt new file mode 100644 index 000000000000..49d517340de3 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/pmu.txt @@ -0,0 +1,24 @@ +* ARC Performance Monitor Unit + +The ARC 700 can be configured with a pipeline performance monitor for counting +CPU and cache events like cache misses and hits. + +Note that: + * ARC 700 refers to a family of ARC processor cores; + - There is only one type of PMU available for the whole family; + - The PMU may support different sets of events; supported events are probed + at boot time, as required by the reference manual. + + * The ARC 700 PMU does not support interrupts; although HW events may be + counted, the HW events themselves cannot serve as a trigger for a sample. + +Required properties: + +- compatible : should contain + "snps,arc700-pmu" + +Example: + +pmu { + compatible = "snps,arc700-pmu"; +}; diff --git a/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt index f770ac0893d4..049675944b78 100644 --- a/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt +++ b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt @@ -1,7 +1,9 @@ Calxeda DDR memory controller Properties: -- compatible : Should be "calxeda,hb-ddr-ctrl" +- compatible : Should be: + - "calxeda,hb-ddr-ctrl" for ECX-1000 + - "calxeda,ecx-2000-ddr-ctrl" for ECX-2000 - reg : Address and size for DDR controller registers. - interrupts : Interrupt for DDR controller. diff --git a/Documentation/devicetree/bindings/crypto/omap-des.txt b/Documentation/devicetree/bindings/crypto/omap-des.txt new file mode 100644 index 000000000000..e8c63bf2e16d --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/omap-des.txt @@ -0,0 +1,30 @@ +OMAP SoC DES crypto Module + +Required properties: + +- compatible : Should contain "ti,omap4-des" +- ti,hwmods: Name of the hwmod associated with the DES module +- reg : Offset and length of the register set for the module +- interrupts : the interrupt-specifier for the DES module +- clocks : A phandle to the functional clock node of the DES module + corresponding to each entry in clock-names +- clock-names : Name of the functional clock, should be "fck" + +Optional properties: +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt + Each entry corresponds to an entry in dma-names +- dma-names: DMA request names should include "tx" and "rx" if present + +Example: + /* DRA7xx SoC */ + des: des@480a5000 { + compatible = "ti,omap4-des"; + ti,hwmods = "des"; + reg = <0x480a5000 0xa0>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 117>, <&sdma 116>; + dma-names = "tx", "rx"; + clocks = <&l3_iclk_div>; + clock-names = "fck"; + }; diff --git a/Documentation/devicetree/bindings/crypto/omap-sham.txt b/Documentation/devicetree/bindings/crypto/omap-sham.txt index f839acd6f0ee..ad9115569611 100644 --- a/Documentation/devicetree/bindings/crypto/omap-sham.txt +++ b/Documentation/devicetree/bindings/crypto/omap-sham.txt @@ -6,7 +6,7 @@ Required properties: SHAM versions: - "ti,omap2-sham" for OMAP2 & OMAP3. - "ti,omap4-sham" for OMAP4 and AM33XX. - Note that these two versions are incompatible. + - "ti,omap5-sham" for OMAP5, DRA7 and AM43XX. - ti,hwmods: Name of the hwmod associated with the SHAM module - reg : Offset and length of the register set for the module - interrupts : the interrupt-specifier for the SHAM module. diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt index e1f343c7a34b..f69bcf5a6343 100644 --- a/Documentation/devicetree/bindings/dma/atmel-dma.txt +++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt @@ -28,7 +28,7 @@ The three cells in order are: dependent: - bit 7-0: peripheral identifier for the hardware handshaking interface. The identifier can be different for tx and rx. - - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 1 for ASAP. + - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 2 for ASAP. Example: diff --git a/Documentation/devicetree/bindings/hwmon/lm90.txt b/Documentation/devicetree/bindings/hwmon/lm90.txt new file mode 100644 index 000000000000..e8632486b9ef --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/lm90.txt @@ -0,0 +1,44 @@ +* LM90 series thermometer. + +Required node properties: +- compatible: manufacturer and chip name, one of + "adi,adm1032" + "adi,adt7461" + "adi,adt7461a" + "gmt,g781" + "national,lm90" + "national,lm86" + "national,lm89" + "national,lm99" + "dallas,max6646" + "dallas,max6647" + "dallas,max6649" + "dallas,max6657" + "dallas,max6658" + "dallas,max6659" + "dallas,max6680" + "dallas,max6681" + "dallas,max6695" + "dallas,max6696" + "onnn,nct1008" + "winbond,w83l771" + "nxp,sa56004" + +- reg: I2C bus address of the device + +- vcc-supply: vcc regulator for the supply voltage. + +Optional properties: +- interrupts: Contains a single interrupt specifier which describes the + LM90 "-ALERT" pin output. + See interrupt-controller/interrupts.txt for the format. + +Example LM90 node: + +temp-sensor { + compatible = "onnn,nct1008"; + reg = <0x4c>; + vcc-supply = <&palmas_ldo6_reg>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>; +} diff --git a/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt new file mode 100644 index 000000000000..1b87b741fa8e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt @@ -0,0 +1,35 @@ +Broadcom Kona Family I2C +========================= + +This I2C controller is used in the following Broadcom SoCs: + + BCM11130 + BCM11140 + BCM11351 + BCM28145 + BCM28155 + +Required Properties +------------------- +- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c" +- reg: Physical base address and length of controller registers +- interrupts: The interrupt number used by the controller +- clocks: clock specifier for the kona i2c external clock +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Refer to clocks/clock-bindings.txt for generic clock consumer +properties. + +Example: + +i2c@3e016000 { + compatible = "brcm,bcm11351-i2c","brcm,kona-i2c"; + reg = <0x3e016000 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&bsc1_clk>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt new file mode 100644 index 000000000000..056732cfdcee --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt @@ -0,0 +1,44 @@ +* Samsung's High Speed I2C controller + +The Samsung's High Speed I2C controller is used to interface with I2C devices +at various speeds ranging from 100khz to 3.4Mhz. + +Required properties: + - compatible: value should be. + -> "samsung,exynos5-hsi2c", for i2c compatible with exynos5 hsi2c. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - #address-cells: always 1 (for i2c addresses) + - #size-cells: always 0 + + - Pinctrl: + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + +Optional properties: + - clock-frequency: Desired operating frequency in Hz of the bus. + -> If not specified, the bus operates in fast-speed mode at + at 100khz. + -> If specified, the bus operates in high-speed mode only if the + clock-frequency is >= 1Mhz. + +Example: + +hsi2c@12ca0000 { + compatible = "samsung,exynos5-hsi2c"; + reg = <0x12ca0000 0x100>; + interrupts = <56>; + clock-frequency = <100000>; + + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt new file mode 100644 index 000000000000..897cfcd5ce92 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -0,0 +1,23 @@ +I2C for R-Car platforms + +Required properties: +- compatible: Must be one of + "renesas,i2c-rcar" + "renesas,i2c-r8a7778" + "renesas,i2c-r8a7779" + "renesas,i2c-r8a7790" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt specifier. + +Optional properties: +- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this + propoerty indicates the default frequency 100 kHz. + +Examples : + +i2c0: i2c@e6500000 { + compatible = "renesas,i2c-rcar-h2"; + reg = <0 0xe6500000 0 0x428>; + interrupts = <0 174 0x4>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt new file mode 100644 index 000000000000..437e0db3823c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt @@ -0,0 +1,41 @@ +ST SSC binding, for I2C mode operation + +Required properties : +- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- clock-names: Must contain "ssc". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. +- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is + allowed through the deglitch circuit. In units of us. +- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is + allowed through the deglitch circuit. In units of us. +- A pinctrl state named "idle" could be defined to set pins in idle state + when I2C instance is not performing a transfer. +- A pinctrl state named "sleep" could be defined to set pins in sleep state + when driver enters in suspend. + + + +Example : + +i2c0: i2c@fed40000 { + compatible = "st,comms-ssc4-i2c"; + reg = <0xfed40000 0x110>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&CLK_S_ICN_REG_0>; + clock-names = "ssc"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0_default>; + st,i2c-min-scl-pulse-width-us = <0>; + st,i2c-min-sda-pulse-width-us = <5>; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt index 491c97b78384..878549ba814d 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -6,7 +6,7 @@ Required properties: ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen support on the platform. ti,x-plate-resistance: X plate resistance - ti,coordiante-readouts: The sequencer supports a total of 16 + ti,coordinate-readouts: The sequencer supports a total of 16 programmable steps each step is used to read a single coordinate. A single readout is enough but multiple reads can diff --git a/Documentation/devicetree/bindings/media/st-rc.txt b/Documentation/devicetree/bindings/media/st-rc.txt new file mode 100644 index 000000000000..05c432d08bca --- /dev/null +++ b/Documentation/devicetree/bindings/media/st-rc.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for ST IRB IP + +Required properties: + - compatible: Should contain "st,comms-irb". + - reg: Base physical address of the controller and length of memory + mapped region. + - interrupts: interrupt-specifier for the sole interrupt generated by + the device. The interrupt specifier format depends on the interrupt + controller parent. + - rx-mode: can be "infrared" or "uhf". This property specifies the L1 + protocol used for receiving remote control signals. rx-mode should + be present iff the rx pins are wired up. + - tx-mode: should be "infrared". This property specifies the L1 + protocol used for transmitting remote control signals. tx-mode should + be present iff the tx pins are wired up. + +Optional properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure muxing + properly for IRB pins. + - clocks : phandle with clock-specifier pair for IRB. + +Example node: + + rc: rc@fe518000 { + compatible = "st,comms-irb"; + reg = <0xfe518000 0x234>; + interrupts = <0 203 0>; + rx-mode = "infrared"; + }; diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt new file mode 100644 index 000000000000..fc2191ecfd6b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/as3722.txt @@ -0,0 +1,194 @@ +* ams AS3722 Power management IC. + +Required properties: +------------------- +- compatible: Must be "ams,as3722". +- reg: I2C device address. +- interrupt-controller: AS3722 has internal interrupt controller which takes the + interrupt request from internal sub-blocks like RTC, regulators, GPIOs as well + as external input. +- #interrupt-cells: Should be set to 2 for IRQ number and flags. + The first cell is the IRQ number. IRQ numbers for different interrupt source + of AS3722 are defined at dt-bindings/mfd/as3722.h + The second cell is the flags, encoded as the trigger masks from binding document + interrupts.txt, using dt-bindings/irq. + +Optional submodule and their properties: +======================================= + +Pinmux and GPIO: +=============== +Device has 8 GPIO pins which can be configured as GPIO as well as the special IO +functions. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Following are properties which is needed if GPIO and pinmux functionality +is required: + Required properties: + ------------------- + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Number of GPIO cells. Refer to binding document + gpio/gpio.txt + + Optional properties: + -------------------- + Following properties are require if pin control setting is required + at boot. + - pinctrl-names: A pinctrl state named "default" be defined, using the + bindings in pinctrl/pinctrl-binding.txt. + - pinctrl[0...n]: Properties to contain the phandle that refer to + different nodes of pin control settings. These nodes represents + the pin control setting of state 0 to state n. Each of these + nodes contains different subnodes to represents some desired + configuration for a list of pins. This configuration can + include the mux function to select on those pin(s), and + various pin configuration parameters, such as pull-up, + open drain. + + Each subnode have following properties: + Required properties: + - pins: List of pins. Valid values of pins properties are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, + gpio6, gpio7 + + Optional properties: + function, bias-disable, bias-pull-up, bias-pull-down, + bias-high-impedance, drive-open-drain. + + Valid values for function properties are: + gpio, interrupt-out, gpio-in-interrupt, + vsup-vbat-low-undebounce-out, + vsup-vbat-low-debounce-out, + voltage-in-standby, oc-pg-sd0, oc-pg-sd6, + powergood-out, pwm-in, pwm-out, clk32k-out, + watchdog-in, soft-reset-in + +Regulators: +=========== +Device has multiple DCDC and LDOs. The node "regulators" is require if regulator +functionality is needed. + +Following are properties of regulator subnode. + + Optional properties: + ------------------- + The input supply of regulators are the optional properties on the + regulator node. The input supply of these regulators are provided + through following properties: + vsup-sd2-supply: Input supply for SD2. + vsup-sd3-supply: Input supply for SD3. + vsup-sd4-supply: Input supply for SD4. + vsup-sd5-supply: Input supply for SD5. + vin-ldo0-supply: Input supply for LDO0. + vin-ldo1-6-supply: Input supply for LDO1 and LDO6. + vin-ldo2-5-7-supply: Input supply for LDO2, LDO5 and LDO7. + vin-ldo3-4-supply: Input supply for LDO3 and LDO4. + vin-ldo9-10-supply: Input supply for LDO9 and LDO10. + vin-ldo11-supply: Input supply for LDO11. + + Optional sub nodes for regulators: + --------------------------------- + The subnodes name is the name of regulator and it must be one of: + sd[0-6], ldo[0-7], ldo[9-11] + + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a description + of standard properties for these sub-nodes. + Additional optional custom properties are listed below. + ams,ext-control: External control of the rail. The option of + this properties will tell which external input is + controlling this rail. Valid values are 0, 1, 2 ad 3. + 0: There is no external control of this rail. + 1: Rail is controlled by ENABLE1 input pin. + 2: Rail is controlled by ENABLE2 input pin. + 3: Rail is controlled by ENABLE3 input pin. + Missing this property on DT will be assume as no + external control. The external control pin macros + are defined @dt-bindings/mfd/as3722.h + + ams,enable-tracking: Enable tracking with SD1, only supported + by LDO3. + +Example: +-------- +#include <dt-bindings/mfd/as3722.h> +... +ams3722 { + compatible = "ams,as3722"; + reg = <0x48>; + + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <2>; + + gpio-controller; + #gpio-cells = <2>; + + pinctrl-names = "default"; + pinctrl-0 = <&as3722_default>; + + as3722_default: pinmux { + gpio0 { + pins = "gpio0"; + function = "gpio"; + bias-pull-down; + }; + + gpio1_2_4_7 { + pins = "gpio1", "gpio2", "gpio4", "gpio7"; + function = "gpio"; + bias-pull-up; + }; + + gpio5 { + pins = "gpio5"; + function = "clk32k_out"; + }; + } + + regulators { + vsup-sd2-supply = <...>; + ... + + sd0 { + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + ams,ext-control = <2>; + }; + + sd1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + ams,ext-control = <1>; + }; + + sd2 { + regulator-name = "vddio_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + sd4 { + regulator-name = "avdd-hdmi-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + }; + + sd5 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + .... + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index c9332c626021..78a840d7510d 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,10 +1,10 @@ * Samsung S2MPS11 Voltage and Current Regulator -The Samsung S2MP211 is a multi-function device which includes voltage and +The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is -interfaced to the host controller using a I2C interface. Each sub-block is -addressed by the host system using different I2C slave address. +interfaced to the host controller using an I2C interface. Each sub-block is +addressed by the host system using different I2C slave addresses. Required properties: - compatible: Should be "samsung,s2mps11-pmic". @@ -43,7 +43,8 @@ sub-node should be of the format as listed below. BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explictly regulator-ramp-delay = <0> can be used for them to disable ramp delay. - In absence of regulator-ramp-delay property, default ramp delay will be used. + In the absence of the regulator-ramp-delay property, the default ramp + delay will be used. NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. @@ -58,10 +59,10 @@ supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number as per the datasheet of s2mps11. - LDOn - - valid values for n are 1 to 28 + - valid values for n are 1 to 38 - Example: LDO0, LD01, LDO28 - BUCKn - - valid values for n are 1 to 9. + - valid values for n are 1 to 10. - Example: BUCK1, BUCK2, BUCK9 Example: diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 1dd622546d06..9046ba06c47a 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -12,6 +12,11 @@ Required properties: Optional properties: - fsl,cd-controller : Indicate to use controller internal card detection - fsl,wp-controller : Indicate to use controller internal write protection +- fsl,delay-line : Specify the number of delay cells for override mode. + This is used to set the clock delay for DLL(Delay Line) on override mode + to select a proper data sampling window in case the clock quality is not good + due to signal path is too long on the board. Please refer to eSDHC/uSDHC + chapter, DLL (Delay Line) section in RM for details. Examples: diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 066a78b034ca..8f3f13315358 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -52,6 +52,9 @@ Optional properties: is specified and the ciu clock is specified then we'll try to set the ciu clock to this at probe time. +* clock-freq-min-max: Minimum and Maximum clock frequency for card output + clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default. + * num-slots: specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the value specified by num-slots. If this property is not specified, the value @@ -66,6 +69,10 @@ Optional properties: * supports-highspeed: Enables support for high speed cards (up to 50MHz) +* caps2-mmc-hs200-1_8v: Supports mmc HS200 SDR 1.8V mode + +* caps2-mmc-hs200-1_2v: Supports mmc HS200 SDR 1.2V mode + * broken-cd: as documented in mmc core bindings. * vmmc-supply: The phandle to the regulator to use for vmmc. If this is @@ -93,8 +100,10 @@ board specific portions as listed below. dwmmc0@12200000 { clock-frequency = <400000000>; + clock-freq-min-max = <400000 200000000>; num-slots = <1>; supports-highspeed; + caps2-mmc-hs200-1_8v; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; diff --git a/Documentation/devicetree/bindings/power/twl-charger.txt b/Documentation/devicetree/bindings/power/twl-charger.txt new file mode 100644 index 000000000000..d5c706216df5 --- /dev/null +++ b/Documentation/devicetree/bindings/power/twl-charger.txt @@ -0,0 +1,20 @@ +TWL BCI (Battery Charger Interface) + +Required properties: +- compatible: + - "ti,twl4030-bci" +- interrupts: two interrupt lines from the TWL SIH (secondary + interrupt handler) - interrupts 9 and 2. + +Optional properties: +- ti,bb-uvolt: microvolts for charging the backup battery. +- ti,bb-uamp: microamps for charging the backup battery. + +Examples: + +bci { + compatible = "ti,twl4030-bci"; + interrupts = <9>, <2>; + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; diff --git a/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt new file mode 100644 index 000000000000..4f6a550184d0 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt @@ -0,0 +1,32 @@ +TI BQ24735 Charge Controller +~~~~~~~~~~ + +Required properties : + - compatible : "ti,bq24735" + +Optional properties : + - interrupts : Specify the interrupt to be used to trigger when the AC + adapter is either plugged in or removed. + - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter + presence. This is a Host GPIO that is configured as an input and + connected to the bq24735. + - ti,charge-current : Used to control and set the charging current. This value + must be between 128mA and 8.128A with a 64mA step resolution. The POR value + is 0x0000h. This number is in mA (e.g. 8192), see spec for more information + about the ChargeCurrent (0x14h) register. + - ti,charge-voltage : Used to control and set the charging voltage. This value + must be between 1.024V and 19.2V with a 16mV step resolution. The POR value + is 0x0000h. This number is in mV (e.g. 19200), see spec for more information + about the ChargeVoltage (0x15h) register. + - ti,input-current : Used to control and set the charger input current. This + value must be between 128mA and 8.064A with a 128mA step resolution. The + POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for + more information about the InputCurrent (0x3fh) register. + +Example: + + bq24735@9 { + compatible = "ti,bq24735"; + reg = <0x9>; + ti,ac-detect-gpios = <&gpio 72 0x1>; + } diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt index 2a4b4bce6110..7fc1b010fa75 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt @@ -1,33 +1,30 @@ -* Freescale 83xx DMA Controller +* Freescale DMA Controllers -Freescale PowerPC 83xx have on chip general purpose DMA controllers. +** Freescale Elo DMA Controller + This is a little-endian 4-channel DMA controller, used in Freescale mpc83xx + series chips such as mpc8315, mpc8349, mpc8379 etc. Required properties: -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8349, mpc8360, etc.) and the second is - "fsl,elo-dma" -- reg : <registers mapping for DMA general status reg> -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. +- compatible : must include "fsl,elo-dma" +- reg : DMA General Status Register, i.e. DGSR which contains + status for all the 4 DMA channels +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller - cell-index : controller index. 0 for controller @ 0x8100 -- interrupts : <interrupt mapping for DMA IRQ> +- interrupts : interrupt specifier for DMA IRQ - interrupt-parent : optional, if needed for interrupt mapping - - DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8349, mpc8350, etc.) and the second is - "fsl,elo-dma-channel". However, see note below. - - reg : <registers mapping for channel> - - cell-index : dma channel index starts at 0. + - compatible : must include "fsl,elo-dma-channel" + However, see note below. + - reg : DMA channel specific registers + - cell-index : DMA channel index starts at 0. Optional properties: - - interrupts : <interrupt mapping for DMA channel IRQ> - (on 83xx this is expected to be identical to - the interrupts property of the parent node) + - interrupts : interrupt specifier for DMA channel IRQ + (on 83xx this is expected to be identical to + the interrupts property of the parent node) - interrupt-parent : optional, if needed for interrupt mapping Example: @@ -70,30 +67,27 @@ Example: }; }; -* Freescale 85xx/86xx DMA Controller - -Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. +** Freescale EloPlus DMA Controller + This is a 4-channel DMA controller with extended addresses and chaining, + mainly used in Freescale mpc85xx/86xx, Pxxx and BSC series chips, such as + mpc8540, mpc8641 p4080, bsc9131 etc. Required properties: -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8540, mpc8540, etc.) and the second is - "fsl,eloplus-dma" -- reg : <registers mapping for DMA general status reg> +- compatible : must include "fsl,eloplus-dma" +- reg : DMA General Status Register, i.e. DGSR which contains + status for all the 4 DMA channels - cell-index : controller index. 0 for controller @ 0x21000, 1 for controller @ 0xc000 -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller - DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8540, mpc8560, etc.) and the second is - "fsl,eloplus-dma-channel". However, see note below. - - cell-index : dma channel index starts at 0. - - reg : <registers mapping for channel> - - interrupts : <interrupt mapping for DMA channel IRQ> + - compatible : must include "fsl,eloplus-dma-channel" + However, see note below. + - cell-index : DMA channel index starts at 0. + - reg : DMA channel specific registers + - interrupts : interrupt specifier for DMA channel IRQ - interrupt-parent : optional, if needed for interrupt mapping Example: @@ -134,6 +128,76 @@ Example: }; }; +** Freescale Elo3 DMA Controller + DMA controller which has same function as EloPlus except that Elo3 has 8 + channels while EloPlus has only 4, it is used in Freescale Txxx and Bxxx + series chips, such as t1040, t4240, b4860. + +Required properties: + +- compatible : must include "fsl,elo3-dma" +- reg : contains two entries for DMA General Status Registers, + i.e. DGSR0 which includes status for channel 1~4, and + DGSR1 for channel 5~8 +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller + +- DMA channel nodes: + - compatible : must include "fsl,eloplus-dma-channel" + - reg : DMA channel specific registers + - interrupts : interrupt specifier for DMA channel IRQ + - interrupt-parent : optional, if needed for interrupt mapping + +Example: +dma@100300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,elo3-dma"; + reg = <0x100300 0x4>, + <0x100600 0x4>; + ranges = <0x0 0x100100 0x500>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + interrupts = <28 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + interrupts = <29 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + interrupts = <30 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + interrupts = <31 2 0 0>; + }; + dma-channel@300 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x300 0x80>; + interrupts = <76 2 0 0>; + }; + dma-channel@380 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x380 0x80>; + interrupts = <77 2 0 0>; + }; + dma-channel@400 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x400 0x80>; + interrupts = <78 2 0 0>; + }; + dma-channel@480 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x480 0x80>; + interrupts = <79 2 0 0>; + }; +}; + Note on DMA channel compatible properties: The compatible property must say "fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA driver (fsldma). Any DMA channel used by fsldma cannot be used by another diff --git a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt index d61fccd40bad..5538de9c2007 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt @@ -15,7 +15,7 @@ Required properties: samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210, Exynos4210 rev0 SoCs samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210, - Exynos4x12 and Exynos5250 SoCs + Exynos4x12, Exynos5250 and Exynos5420 SoCs - reg: base address and size of register area - interrupts: list of timer interrupts (one interrupt per timer, starting at timer 0) diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt index 4c85c4c69584..2ba5f9c023ac 100644 --- a/Documentation/devicetree/bindings/spi/omap-spi.txt +++ b/Documentation/devicetree/bindings/spi/omap-spi.txt @@ -2,8 +2,8 @@ OMAP2+ McSPI device Required properties: - compatible : - - "ti,omap2-spi" for OMAP2 & OMAP3. - - "ti,omap4-spi" for OMAP4+. + - "ti,omap2-mcspi" for OMAP2 & OMAP3. + - "ti,omap4-mcspi" for OMAP4+. - ti,spi-num-cs : Number of chipselect supported by the instance. - ti,hwmods: Name of the hwmod associated to the McSPI - ti,pindir-d0-out-d1-in: Select the D0 pin as output and D1 as diff --git a/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt index 1e4fc727f3b1..764db86d441a 100644 --- a/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt +++ b/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt @@ -10,12 +10,16 @@ Required properties: last value in the array represents a 100% duty cycle (brightest). - default-brightness-level: the default brightness level (index into the array defined by the "brightness-levels" property) + - power-supply: regulator for supply voltage Optional properties: - pwm-names: a list of names for the PWM devices specified in the "pwms" property (see PWM binding[0]) + - enable-gpios: contains a single GPIO specifier for the GPIO which enables + and disables the backlight (see GPIO binding[1]) [0]: Documentation/devicetree/bindings/pwm/pwm.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt Example: @@ -25,4 +29,7 @@ Example: brightness-levels = <0 4 8 16 32 64 128 255>; default-brightness-level = <6>; + + power-supply = <&vdd_bl_reg>; + enable-gpios = <&gpio 58 0>; }; diff --git a/Documentation/devicetree/bindings/watchdog/dw_wdt.txt b/Documentation/devicetree/bindings/watchdog/dw_wdt.txt new file mode 100644 index 000000000000..08e16f684f2d --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/dw_wdt.txt @@ -0,0 +1,21 @@ +Synopsys Designware Watchdog Timer + +Required Properties: + +- compatible : Should contain "snps,dw-wdt" +- reg : Base address and size of the watchdog timer registers. +- clocks : phandle + clock-specifier for the clock that drives the + watchdog timer. + +Optional Properties: + +- interrupts : The interrupt used for the watchdog timeout warning. + +Example: + + watchdog0: wd@ffd02000 { + compatible = "snps,dw-wdt"; + reg = <0xffd02000 0x1000>; + interrupts = <0 171 4>; + clocks = <&per_base_clk>; + }; diff --git a/Documentation/devicetree/bindings/gpio/men-a021-wdt.txt b/Documentation/devicetree/bindings/watchdog/men-a021-wdt.txt index 370dee3226d9..370dee3226d9 100644 --- a/Documentation/devicetree/bindings/gpio/men-a021-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/men-a021-wdt.txt diff --git a/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt b/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt new file mode 100644 index 000000000000..1169857d1d12 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt @@ -0,0 +1,15 @@ +MOXA ART Watchdog timer + +Required properties: + +- compatible : Must be "moxa,moxart-watchdog" +- reg : Should contain registers location and length +- clocks : Should contain phandle for the clock that drives the counter + +Example: + + watchdog: watchdog@98500000 { + compatible = "moxa,moxart-watchdog"; + reg = <0x98500000 0x10>; + clocks = <&coreclk>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt b/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt new file mode 100644 index 000000000000..d7bab3db9d1f --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt @@ -0,0 +1,19 @@ +Ralink Watchdog Timers + +Required properties: +- compatible: must be "ralink,rt2880-wdt" +- reg: physical base address of the controller and length of the register range + +Optional properties: +- interrupt-parent: phandle to the INTC device node +- interrupts: Specify the INTC interrupt number + +Example: + + watchdog@120 { + compatible = "ralink,rt2880-wdt"; + reg = <0x120 0x10>; + + interrupt-parent = <&intc>; + interrupts = <1>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt new file mode 100644 index 000000000000..9cbc76c89b2b --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt @@ -0,0 +1,14 @@ +SiRFSoC Timer and Watchdog Timer(WDT) Controller + +Required properties: +- compatible: "sirf,prima2-tick" +- reg: Address range of tick timer/WDT register set +- interrupts: interrupt number to the cpu + +Example: + +timer@b0020000 { + compatible = "sirf,prima2-tick"; + reg = <0xb0020000 0x1000>; + interrupts = <0>; +}; diff --git a/Documentation/dmatest.txt b/Documentation/dmatest.txt index a2b5663eae26..dd77a81bdb80 100644 --- a/Documentation/dmatest.txt +++ b/Documentation/dmatest.txt @@ -15,39 +15,48 @@ be built as module or inside kernel. Let's consider those cases. Part 2 - When dmatest is built as a module... -After mounting debugfs and loading the module, the /sys/kernel/debug/dmatest -folder with nodes will be created. There are two important files located. First -is the 'run' node that controls run and stop phases of the test, and the second -one, 'results', is used to get the test case results. - -Note that in this case test will not run on load automatically. - Example of usage: + % modprobe dmatest channel=dma0chan0 timeout=2000 iterations=1 run=1 + +...or: + % modprobe dmatest % echo dma0chan0 > /sys/module/dmatest/parameters/channel % echo 2000 > /sys/module/dmatest/parameters/timeout % echo 1 > /sys/module/dmatest/parameters/iterations - % echo 1 > /sys/kernel/debug/dmatest/run + % echo 1 > /sys/module/dmatest/parameters/run + +...or on the kernel command line: + + dmatest.channel=dma0chan0 dmatest.timeout=2000 dmatest.iterations=1 dmatest.run=1 Hint: available channel list could be extracted by running the following command: % ls -1 /sys/class/dma/ -After a while you will start to get messages about current status or error like -in the original code. +Once started a message like "dmatest: Started 1 threads using dma0chan0" is +emitted. After that only test failure messages are reported until the test +stops. Note that running a new test will not stop any in progress test. -The following command should return actual state of the test. - % cat /sys/kernel/debug/dmatest/run - -To wait for test done the user may perform a busy loop that checks the state. - - % while [ $(cat /sys/kernel/debug/dmatest/run) = "Y" ] - > do - > echo -n "." - > sleep 1 - > done - > echo +The following command returns the state of the test. + % cat /sys/module/dmatest/parameters/run + +To wait for test completion userpace can poll 'run' until it is false, or use +the wait parameter. Specifying 'wait=1' when loading the module causes module +initialization to pause until a test run has completed, while reading +/sys/module/dmatest/parameters/wait waits for any running test to complete +before returning. For example, the following scripts wait for 42 tests +to complete before exiting. Note that if 'iterations' is set to 'infinite' then +waiting is disabled. + +Example: + % modprobe dmatest run=1 iterations=42 wait=1 + % modprobe -r dmatest +...or: + % modprobe dmatest run=1 iterations=42 + % cat /sys/module/dmatest/parameters/wait + % modprobe -r dmatest Part 3 - When built-in in the kernel... @@ -62,21 +71,22 @@ case. You always could check them at run-time by running Part 4 - Gathering the test results -The module provides a storage for the test results in the memory. The gathered -data could be used after test is done. +Test results are printed to the kernel log buffer with the format: -The special file 'results' in the debugfs represents gathered data of the in -progress test. The messages collected are printed to the kernel log as well. +"dmatest: result <channel>: <test id>: '<error msg>' with src_off=<val> dst_off=<val> len=<val> (<err code>)" Example of output: - % cat /sys/kernel/debug/dmatest/results - dma0chan0-copy0: #1: No errors with src_off=0x7bf dst_off=0x8ad len=0x3fea (0) + % dmesg | tail -n 1 + dmatest: result dma0chan0-copy0: #1: No errors with src_off=0x7bf dst_off=0x8ad len=0x3fea (0) The message format is unified across the different types of errors. A number in the parens represents additional information, e.g. error code, error counter, -or status. +or status. A test thread also emits a summary line at completion listing the +number of tests executed, number that failed, and a result code. -Comparison between buffers is stored to the dedicated structure. +Example: + % dmesg | tail -n 1 + dmatest: dma0chan0-copy0: summary 1 test, 0 failures 1000 iops 100000 KB/s (0) -Note that the verify result is now accessible only via file 'results' in the -debugfs. +The details of a data miscompare error are also emitted, but do not follow the +above format. diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90 index b466974e142f..ab81013cc390 100644 --- a/Documentation/hwmon/lm90 +++ b/Documentation/hwmon/lm90 @@ -122,6 +122,12 @@ Supported chips: Prefix: 'g781' Addresses scanned: I2C 0x4c, 0x4d Datasheet: Not publicly available from GMT + * Texas Instruments TMP451 + Prefix: 'tmp451' + Addresses scanned: I2C 0x4c + Datasheet: Publicly available at TI website + http://www.ti.com/litv/pdf/sbos686 + Author: Jean Delvare <khali@linux-fr.org> diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 index d29dea0f3232..7b0dcdb57173 100644 --- a/Documentation/i2c/busses/i2c-i801 +++ b/Documentation/i2c/busses/i2c-i801 @@ -25,6 +25,7 @@ Supported adapters: * Intel Avoton (SOC) * Intel Wellsburg (PCH) * Intel Coleto Creek (PCH) + * Intel Wildcat Point-LP (PCH) Datasheets: Publicly available at the Intel website On Intel Patsburg and later chipsets, both the normal host SMBus controller diff --git a/Documentation/input/gamepad.txt b/Documentation/input/gamepad.txt index 8002c894c6b0..31bb6a4029ef 100644 --- a/Documentation/input/gamepad.txt +++ b/Documentation/input/gamepad.txt @@ -122,12 +122,14 @@ D-Pad: BTN_DPAD_* Analog buttons are reported as: ABS_HAT0X and ABS_HAT0Y + (for ABS values negative is left/up, positive is right/down) Analog-Sticks: The left analog-stick is reported as ABS_X, ABS_Y. The right analog stick is reported as ABS_RX, ABS_RY. Zero, one or two sticks may be present. If analog-sticks provide digital buttons, they are mapped accordingly as BTN_THUMBL (first/left) and BTN_THUMBR (second/right). + (for ABS values negative is left/up, positive is right/down) Triggers: Trigger buttons can be available as digital or analog buttons or both. User- @@ -138,6 +140,7 @@ Triggers: ABS_HAT2X (right/ZR) and BTN_TL2 or ABS_HAT2Y (left/ZL). If only one trigger-button combination is present (upper+lower), they are reported as "right" triggers (BTN_TR/ABS_HAT1X). + (ABS trigger values start at 0, pressure is reported as positive values) Menu-Pad: Menu buttons are always digital and are mapped according to their location diff --git a/Documentation/kbuild/kconfig.txt b/Documentation/kbuild/kconfig.txt index 8ef6dbb6a462..bbc99c0c1094 100644 --- a/Documentation/kbuild/kconfig.txt +++ b/Documentation/kbuild/kconfig.txt @@ -20,16 +20,9 @@ symbols have been introduced. To see a list of new config symbols when using "make oldconfig", use cp user/some/old.config .config - yes "" | make oldconfig >conf.new + make listnewconfig -and the config program will list as (NEW) any new symbols that have -unknown values. Of course, the .config file is also updated with -new (default) values, so you can use: - - grep "(NEW)" conf.new - -to see the new config symbols or you can use diffconfig to see the -differences between the previous and new .config files: +and the config program will list any new symbols, one per line. scripts/diffconfig .config.old .config | less diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 8b8a05787641..3c12d9a7ed00 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -577,9 +577,6 @@ tcp_limit_output_bytes - INTEGER typical pfifo_fast qdiscs. tcp_limit_output_bytes limits the number of bytes on qdisc or device to reduce artificial RTT/cwnd and reduce bufferbloat. - Note: For GSO/TSO enabled flows, we try to have at least two - packets in flight. Reducing tcp_limit_output_bytes might also - reduce the size of individual GSO packet (64KB being the max) Default: 131072 tcp_challenge_ack_limit - INTEGER diff --git a/Documentation/power/power_supply_class.txt b/Documentation/power/power_supply_class.txt index 3f10b39b0346..89a8816990ff 100644 --- a/Documentation/power/power_supply_class.txt +++ b/Documentation/power/power_supply_class.txt @@ -135,11 +135,11 @@ CAPACITY_LEVEL - capacity level. This corresponds to POWER_SUPPLY_CAPACITY_LEVEL_*. TEMP - temperature of the power supply. -TEMP_ALERT_MIN - minimum battery temperature alert value in milli centigrade. -TEMP_ALERT_MAX - maximum battery temperature alert value in milli centigrade. +TEMP_ALERT_MIN - minimum battery temperature alert. +TEMP_ALERT_MAX - maximum battery temperature alert. TEMP_AMBIENT - ambient temperature. -TEMP_AMBIENT_ALERT_MIN - minimum ambient temperature alert value in milli centigrade. -TEMP_AMBIENT_ALERT_MAX - maximum ambient temperature alert value in milli centigrade. +TEMP_AMBIENT_ALERT_MIN - minimum ambient temperature alert. +TEMP_AMBIENT_ALERT_MAX - maximum ambient temperature alert. TIME_TO_EMPTY - seconds left for battery to be considered empty (i.e. while battery powers a load) diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt index 0f54333b0ff2..b6ce00b2be9a 100644 --- a/Documentation/power/runtime_pm.txt +++ b/Documentation/power/runtime_pm.txt @@ -547,13 +547,11 @@ helper functions described in Section 4. In that case, pm_runtime_resume() should be used. Of course, for this purpose the device's runtime PM has to be enabled earlier by calling pm_runtime_enable(). -If the device bus type's or driver's ->probe() callback runs -pm_runtime_suspend() or pm_runtime_idle() or their asynchronous counterparts, -they will fail returning -EAGAIN, because the device's usage counter is -incremented by the driver core before executing ->probe(). Still, it may be -desirable to suspend the device as soon as ->probe() has finished, so the driver -core uses pm_runtime_put_sync() to invoke the subsystem-level idle callback for -the device at that time. +It may be desirable to suspend the device once ->probe() has finished. +Therefore the driver core uses the asyncronous pm_request_idle() to submit a +request to execute the subsystem-level idle callback for the device at that +time. A driver that makes use of the runtime autosuspend feature, may want to +update the last busy mark before returning from ->probe(). Moreover, the driver core prevents runtime PM callbacks from racing with the bus notifier callback in __device_release_driver(), which is necessary, because the @@ -656,7 +654,7 @@ out the following operations: __pm_runtime_disable() with 'false' as the second argument for every device right before executing the subsystem-level .suspend_late() callback for it. - * During system resume it calls pm_runtime_enable() and pm_runtime_put_sync() + * During system resume it calls pm_runtime_enable() and pm_runtime_put() for every device right after executing the subsystem-level .resume_early() callback and right after executing the subsystem-level .resume() callback for it, respectively. diff --git a/Documentation/pwm.txt b/Documentation/pwm.txt index 1039b68fe9c6..93cb97974986 100644 --- a/Documentation/pwm.txt +++ b/Documentation/pwm.txt @@ -39,7 +39,7 @@ New users should use the pwm_get() function and pass to it the consumer device or a consumer name. pwm_put() is used to free the PWM device. Managed variants of these functions, devm_pwm_get() and devm_pwm_put(), also exist. -After being requested a PWM has to be configured using: +After being requested, a PWM has to be configured using: int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns); @@ -94,7 +94,7 @@ for new drivers to use the generic PWM framework. A new PWM controller/chip can be added using pwmchip_add() and removed again with pwmchip_remove(). pwmchip_add() takes a filled in struct pwm_chip as argument which provides a description of the PWM chip, the -number of PWM devices provider by the chip and the chip-specific +number of PWM devices provided by the chip and the chip-specific implementation of the supported PWM operations to the framework. Locking diff --git a/Documentation/timers/00-INDEX b/Documentation/timers/00-INDEX index a9248da5cdbc..ef2ccbf77fa2 100644 --- a/Documentation/timers/00-INDEX +++ b/Documentation/timers/00-INDEX @@ -8,5 +8,9 @@ hpet_example.c - sample hpet timer test program hrtimers.txt - subsystem for high-resolution kernel timers +NO_HZ.txt + - Summary of the different methods for the scheduler clock-interrupts management. +timers-howto.txt + - how to insert delays in the kernel the right (tm) way. timer_stats.txt - timer usage statistics diff --git a/Documentation/usb/gadget_configfs.txt b/Documentation/usb/gadget_configfs.txt index 8ec2a67c39b7..4cf53e406613 100644 --- a/Documentation/usb/gadget_configfs.txt +++ b/Documentation/usb/gadget_configfs.txt @@ -26,7 +26,7 @@ Linux provides a number of functions for gadgets to use. Creating a gadget means deciding what configurations there will be and which functions each configuration will provide. -Configfs (please see Documentation/filesystems/configfs/*) lends itslef nicely +Configfs (please see Documentation/filesystems/configfs/*) lends itself nicely for the purpose of telling the kernel about the above mentioned decision. This document is about how to do it. @@ -99,7 +99,7 @@ directories must be created: $ mkdir configs/<name>.<number> where <name> can be any string which is legal in a filesystem and the -<numebr> is the configuration's number, e.g.: +<number> is the configuration's number, e.g.: $ mkdir configs/c.1 @@ -327,7 +327,7 @@ from the buffer to the cs), but it is up to the implementer of the two functions to decide what they actually do. typedef struct configured_structure cs; -typedef struc specific_attribute sa; +typedef struct specific_attribute sa; sa +----------------------------------+ diff --git a/Documentation/vm/00-INDEX b/Documentation/vm/00-INDEX index 5481c8ba3412..a39d06680e1c 100644 --- a/Documentation/vm/00-INDEX +++ b/Documentation/vm/00-INDEX @@ -4,10 +4,12 @@ active_mm.txt - An explanation from Linus about tsk->active_mm vs tsk->mm. balance - various information on memory balancing. -hugepage-mmap.c - - Example app using huge page memory with the mmap system call. -hugepage-shm.c - - Example app using huge page memory with Sys V shared memory system calls. +cleancache.txt + - Intro to cleancache and page-granularity victim cache. +frontswap.txt + - Outline frontswap, part of the transcendent memory frontend. +highmem.txt + - Outline of highmem and common issues. hugetlbpage.txt - a brief summary of hugetlbpage support in the Linux kernel. hwpoison.txt @@ -16,21 +18,23 @@ ksm.txt - how to use the Kernel Samepage Merging feature. locking - info on how locking and synchronization is done in the Linux vm code. -map_hugetlb.c - - an example program that uses the MAP_HUGETLB mmap flag. numa - information about NUMA specific code in the Linux vm. numa_memory_policy.txt - documentation of concepts and APIs of the 2.6 memory policy support. overcommit-accounting - description of the Linux kernels overcommit handling modes. -page-types.c - - Tool for querying page flags page_migration - description of page migration in NUMA systems. pagemap.txt - pagemap, from the userspace perspective slub.txt - a short users guide for SLUB. +soft-dirty.txt + - short explanation for soft-dirty PTEs +transhuge.txt + - Transparent Hugepage Support, alternative way of using hugepages. unevictable-lru.txt - Unevictable LRU infrastructure +zswap.txt + - Intro to compressed cache for swap pages |