diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
7 files changed, 74 insertions, 21 deletions
diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt index baadbb11fe98..5083c0b834b2 100644 --- a/Documentation/devicetree/bindings/clock/imx23-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -60,11 +60,6 @@ clks: clkctrl@80040000 { compatible = "fsl,imx23-clkctrl"; reg = <0x80040000 0x2000>; #clock-cells = <1>; - clock-output-names = - ... - "uart", /* 32 */ - ... - "end_of_list"; }; auart0: serial@8006c000 { diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt index c2a3525ecb4e..db4f2f05c4d0 100644 --- a/Documentation/devicetree/bindings/clock/imx25-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -146,10 +146,6 @@ clks: ccm@53f80000 { compatible = "fsl,imx25-ccm"; reg = <0x53f80000 0x4000>; interrupts = <31>; - clock-output-names = ... - "uart_ipg", - "uart_serial", - ...; }; uart1: serial@43f90000 { diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt index 52a49a4a50b3..e6587af62ff0 100644 --- a/Documentation/devicetree/bindings/clock/imx28-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -83,11 +83,6 @@ clks: clkctrl@80040000 { compatible = "fsl,imx28-clkctrl"; reg = <0x80040000 0x2000>; #clock-cells = <1>; - clock-output-names = - ... - "uart", /* 45 */ - ... - "end_of_list"; }; auart0: serial@8006a000 { diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index d77b4e68dc42..f73fdf595568 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -211,10 +211,6 @@ clks: ccm@020c4000 { reg = <0x020c4000 0x4000>; interrupts = <0 87 0x04 0 88 0x04>; #clock-cells = <1>; - clock-output-names = ... - "uart_ipg", - "uart_serial", - ...; }; uart1: serial@02020000 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt index 558cdf3c9abc..d4eab9227ea4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt @@ -1,4 +1,19 @@ -GPIO line that should be set high/low to power off a device +Driver a GPIO line that can be used to turn the power off. + +The driver supports both level triggered and edge triggered power off. +At driver load time, the driver will request the given gpio line and +install a pm_power_off handler. If the optional properties 'input' is +not found, the GPIO line will be driven in the inactive +state. Otherwise its configured as an input. + +When the pm_power_off is called, the gpio is configured as an output, +and drive active, so triggering a level triggered power off +condition. This will also cause an inactive->active edge condition, so +triggering positive edge triggered power off. After a delay of 100ms, +the GPIO is set to inactive, thus causing an active->inactive edge, +triggering negative edge triggered power off. After another 100ms +delay the GPIO is driver active again. If the power is still on and +the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. Required properties: - compatible : should be "gpio-poweroff". @@ -13,10 +28,9 @@ Optional properties: property is not specified, the GPIO is initialized as an output in its inactive state. - Examples: gpio-poweroff { compatible = "gpio-poweroff"; - gpios = <&gpio 4 0>; /* GPIO 4 Active Low */ + gpios = <&gpio 4 0>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt new file mode 100644 index 000000000000..c596a6ad3285 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt @@ -0,0 +1,47 @@ +CSR SiRFprimaII pinmux controller + +Required properties: +- compatible : "sirf,prima2-pinctrl" +- reg : Address range of the pinctrl registers +- interrupts : Interrupts used by every GPIO group +- gpio-controller : Indicates this device is a GPIO controller +- interrupt-controller : Marks the device node as an interrupt controller +Optional properties: +- sirf,pullups : if n-th bit of m-th bank is set, set a pullup on GPIO-n of bank m +- sirf,pulldowns : if n-th bit of m-th bank is set, set a pulldown on GPIO-n of bank m + +Please refer to pinctrl-bindings.txt in this directory for details of the common +pinctrl bindings used by client devices. + +SiRFprimaII's pinmux nodes act as a container for an abitrary number of subnodes. +Each of these subnodes represents some desired configuration for a group of pins. + +Required subnode-properties: +- sirf,pins : An array of strings. Each string contains the name of a group. +- sirf,function: A string containing the name of the function to mux to the + group. + + Valid values for group and function names can be found from looking at the + group and function arrays in driver files: + drivers/pinctrl/pinctrl-sirf.c + +For example, pinctrl might have subnodes like the following: + uart2_pins_a: uart2@0 { + uart { + sirf,pins = "uart2grp"; + sirf,function = "uart2"; + }; + }; + uart2_noflow_pins_a: uart2@1 { + uart { + sirf,pins = "uart2_nostreamctrlgrp"; + sirf,function = "uart2_nostreamctrl"; + }; + }; + +For a specific board, if it wants to use uart2 without hardware flow control, +it can add the following to its board-specific .dts file. +uart2: uart@0xb0070000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_noflow_pins_a>; +} diff --git a/Documentation/devicetree/bindings/watchdog/twl4030-wdt.txt b/Documentation/devicetree/bindings/watchdog/twl4030-wdt.txt new file mode 100644 index 000000000000..80a37193c0b8 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/twl4030-wdt.txt @@ -0,0 +1,10 @@ +Device tree bindings for twl4030-wdt driver (TWL4030 watchdog) + +Required properties: + compatible = "ti,twl4030-wdt"; + +Example: + +watchdog { + compatible = "ti,twl4030-wdt"; +}; |