3 files changed, 93 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/calxeda-xgmac.txt b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt
new file mode 100644
index 000000000000..411727a3f82d
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt
@@ -0,0 +1,15 @@
+* Calxeda Highbank 10Gb XGMAC Ethernet
+
+Required properties:
+- compatible : Should be "calxeda,hb-xgmac"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt.
+  The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt.
+
+Example:
+
+ethernet@fff50000 {
+        compatible = "calxeda,hb-xgmac";
+        reg = <0xfff50000 0x1000>;
+        interrupts = <0 77 4  0 78 4  0 79 4>;
+};
diff --git a/Documentation/devicetree/bindings/net/can/cc770.txt b/Documentation/devicetree/bindings/net/can/cc770.txt
new file mode 100644
index 000000000000..77027bf6460a
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/cc770.txt
@@ -0,0 +1,53 @@
+Memory mapped Bosch CC770 and Intel AN82527 CAN controller
+
+Note: The CC770 is a CAN controller from Bosch, which is 100%
+compatible with the old AN82527 from Intel, but with "bugs" being fixed.
+
+Required properties:
+
+- compatible : should be "bosch,cc770" for the CC770 and "intc,82527"
+	for the AN82527.
+
+- reg : should specify the chip select, address offset and size required
+	to map the registers of the controller. The size is usually 0x80.
+
+- interrupts : property with a value describing the interrupt source
+	(number and sensitivity) required for the controller.
+
+Optional properties:
+
+- bosch,external-clock-frequency : frequency of the external oscillator
+	clock in Hz. Note that the internal clock frequency used by the
+	controller is half of that value. If not specified, a default
+	value of 16000000 (16 MHz) is used.
+
+- bosch,clock-out-frequency : slock frequency in Hz on the CLKOUT pin.
+	If not specified or if the specified value is 0, the CLKOUT pin
+	will be disabled.
+
+- bosch,slew-rate : slew rate of the CLKOUT signal. If not specified,
+	a resonable value will be calculated.
+
+- bosch,disconnect-rx0-input : see data sheet.
+
+- bosch,disconnect-rx1-input : see data sheet.
+
+- bosch,disconnect-tx1-output : see data sheet.
+
+- bosch,polarity-dominant : see data sheet.
+
+- bosch,divide-memory-clock : see data sheet.
+
+- bosch,iso-low-speed-mux : see data sheet.
+
+For further information, please have a look to the CC770 or AN82527.
+
+Examples:
+
+can@3,100 {
+	compatible = "bosch,cc770";
+	reg = <3 0x100 0x80>;
+	interrupts = <2 0>;
+	interrupt-parent = <&mpic>;
+	bosch,external-clock-frequency = <16000000>;
+};
diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt
new file mode 100644
index 000000000000..44afa0e5057d
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/macb.txt
@@ -0,0 +1,25 @@
+* Cadence MACB/GEM Ethernet controller
+
+Required properties:
+- compatible: Should be "cdns,[<chip>-]{macb|gem}"
+  Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
+  Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
+  Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on
+  the Cadence GEM, or the generic form: "cdns,gem".
+- reg: Address and length of the register set for the device
+- interrupts: Should contain macb interrupt
+- phy-mode: String, operation mode of the PHY interface.
+  Supported values are: "mii", "rmii", "gmii", "rgmii".
+
+Optional properties:
+- local-mac-address: 6 bytes, mac address
+
+Examples:
+
+	macb0: ethernet@fffc4000 {
+		compatible = "cdns,at32ap7000-macb";
+		reg = <0xfffc4000 0x4000>;
+		interrupts = <21>;
+		phy-mode = "rmii";
+		local-mac-address = [3a 0e 03 04 05 06];
+	};