diff options
Diffstat (limited to 'Documentation/devicetree/bindings/i2c')
4 files changed, 143 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt new file mode 100644 index 000000000000..1b87b741fa8e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt @@ -0,0 +1,35 @@ +Broadcom Kona Family I2C +========================= + +This I2C controller is used in the following Broadcom SoCs: + + BCM11130 + BCM11140 + BCM11351 + BCM28145 + BCM28155 + +Required Properties +------------------- +- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c" +- reg: Physical base address and length of controller registers +- interrupts: The interrupt number used by the controller +- clocks: clock specifier for the kona i2c external clock +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Refer to clocks/clock-bindings.txt for generic clock consumer +properties. + +Example: + +i2c@3e016000 { + compatible = "brcm,bcm11351-i2c","brcm,kona-i2c"; + reg = <0x3e016000 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&bsc1_clk>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt new file mode 100644 index 000000000000..056732cfdcee --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt @@ -0,0 +1,44 @@ +* Samsung's High Speed I2C controller + +The Samsung's High Speed I2C controller is used to interface with I2C devices +at various speeds ranging from 100khz to 3.4Mhz. + +Required properties: + - compatible: value should be. + -> "samsung,exynos5-hsi2c", for i2c compatible with exynos5 hsi2c. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - #address-cells: always 1 (for i2c addresses) + - #size-cells: always 0 + + - Pinctrl: + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + +Optional properties: + - clock-frequency: Desired operating frequency in Hz of the bus. + -> If not specified, the bus operates in fast-speed mode at + at 100khz. + -> If specified, the bus operates in high-speed mode only if the + clock-frequency is >= 1Mhz. + +Example: + +hsi2c@12ca0000 { + compatible = "samsung,exynos5-hsi2c"; + reg = <0x12ca0000 0x100>; + interrupts = <56>; + clock-frequency = <100000>; + + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt new file mode 100644 index 000000000000..897cfcd5ce92 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -0,0 +1,23 @@ +I2C for R-Car platforms + +Required properties: +- compatible: Must be one of + "renesas,i2c-rcar" + "renesas,i2c-r8a7778" + "renesas,i2c-r8a7779" + "renesas,i2c-r8a7790" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt specifier. + +Optional properties: +- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this + propoerty indicates the default frequency 100 kHz. + +Examples : + +i2c0: i2c@e6500000 { + compatible = "renesas,i2c-rcar-h2"; + reg = <0 0xe6500000 0 0x428>; + interrupts = <0 174 0x4>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt new file mode 100644 index 000000000000..437e0db3823c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt @@ -0,0 +1,41 @@ +ST SSC binding, for I2C mode operation + +Required properties : +- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- clock-names: Must contain "ssc". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. +- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is + allowed through the deglitch circuit. In units of us. +- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is + allowed through the deglitch circuit. In units of us. +- A pinctrl state named "idle" could be defined to set pins in idle state + when I2C instance is not performing a transfer. +- A pinctrl state named "sleep" could be defined to set pins in sleep state + when driver enters in suspend. + + + +Example : + +i2c0: i2c@fed40000 { + compatible = "st,comms-ssc4-i2c"; + reg = <0xfed40000 0x110>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&CLK_S_ICN_REG_0>; + clock-names = "ssc"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0_default>; + st,i2c-min-scl-pulse-width-us = <0>; + st,i2c-min-sda-pulse-width-us = <5>; +}; |