Diffstat (limited to 'Documentation/cdrom/ide-cd')
1 files changed, 9 insertions, 9 deletions
diff --git a/Documentation/cdrom/ide-cd b/Documentation/cdrom/ide-cd
index 29721bfcde12..91c0dcc6fa5c 100644
@@ -45,7 +45,7 @@ This driver provides the following features:
0. The ide-cd relies on the ide disk driver. See
- Documentation/ide.txt for up-to-date information on the ide
+ Documentation/ide/ide.txt for up-to-date information on the ide
1. Make sure that the ide and ide-cd drivers are compiled into the
@@ -64,7 +64,7 @@ This driver provides the following features:
Depending on what type of IDE interface you have, you may need to
specify additional configuration options. See
2. You should also ensure that the iso9660 filesystem is either
compiled into the kernel or available as a loadable module. You
@@ -84,7 +84,7 @@ This driver provides the following features:
on the primary IDE interface are called `hda' and `hdb',
respectively. The drives on the secondary interface are called
`hdc' and `hdd'. (Interfaces at other locations get other letters
- in the third position; see Documentation/ide.txt.)
+ in the third position; see Documentation/ide/ide.txt.)
If you want your CDROM drive to be found automatically by the
driver, you should make sure your IDE interface uses either the
@@ -93,7 +93,7 @@ This driver provides the following features:
be jumpered as `master'. (If for some reason you cannot configure
your system in this manner, you can probably still use the driver.
You may have to pass extra configuration information to the kernel
- when you boot, however. See Documentation/ide.txt for more
+ when you boot, however. See Documentation/ide/ide.txt for more
4. Boot the system. If the drive is recognized, you should see a
@@ -201,7 +201,7 @@ TEST
This section discusses some common problems encountered when trying to
use the driver, and some possible solutions. Note that if you are
experiencing problems, you should probably also review
-Documentation/ide.txt for current information about the underlying
+Documentation/ide/ide.txt for current information about the underlying
IDE support code. Some of these items apply only to earlier versions
of the driver, but are mentioned here for completeness.
@@ -211,7 +211,7 @@ from the driver.
a. Drive is not detected during booting.
- Review the configuration instructions above and in
- Documentation/ide.txt, and check how your hardware is
+ Documentation/ide/ide.txt, and check how your hardware is
- If your drive is the only device on an IDE interface, it should
@@ -219,7 +219,7 @@ a. Drive is not detected during booting.
- If your IDE interface is not at the standard addresses of 0x170
or 0x1f0, you'll need to explicitly inform the driver using a
- lilo option. See Documentation/ide.txt. (This feature was
+ lilo option. See Documentation/ide/ide.txt. (This feature was
added around kernel version 1.3.30.)
- If the autoprobing is not finding your drive, you can tell the
@@ -245,7 +245,7 @@ a. Drive is not detected during booting.
Support for some interfaces needing extra initialization is
provided in later 1.3.x kernels. You may need to turn on
additional kernel configuration options to get them to work;
- see Documentation/ide.txt.
+ see Documentation/ide/ide.txt.
Even if support is not available for your interface, you may be
able to get it to work with the following procedure. First boot
@@ -299,7 +299,7 @@ c. System hangups.
be worked around by specifying the `serialize' option when
booting. Recent kernels should be able to detect the need for
this automatically in most cases, but the detection is not
- foolproof. See Documentation/ide.txt for more information
+ foolproof. See Documentation/ide/ide.txt for more information
about the `serialize' option and the CMD640B.
- Note that many MS-DOS CDROM drivers will work with such buggy